Search Documents

By Bryan Ulrich

On March 20, 2014, the ?Roundtable Discussion on Innovations in Heap Leaching and Mine Waste Management? was hosted by Knight Piésold and Co. at the Red Lion Hotel in Elko, NV. This topic is timely, and formed something of a lead into the inaugural ?Workshop on Innovations in Waste Rock, Tails and Heap Leach Management.? That workshop, which grew from the 2013 Elko Roundtable, was held on the University of Nevada, Reno (UNR) campus on May 19, 2014. The workshop was hosted by UNR and the University of British Columbia. Knight Piésold?s local representatives, Bryan Ulrich and Logan Jensen, were joined by Tom Kerr, president of Knight Piésold?s, U.S. practice; Rick Frechette, senior vice president, environmental services and Jeff Coffin, geotechnical engineer, from the Denver, CO office for the roundtable event. The event played host to about two dozen attendees from several western states.

By Thomas M. Barczak

The era of the shield-supported longwall face began in the United States a little over 25 years ago. The most fundamental development of the shield in the past 25 years has been an increase in size and capacity and a progression toward two-legged designs in favor over four-legged shields. Is the “bigger-the-better” design philosophy justified? The advantage of the two-legged design is largely attributed to its active horizontal force caused by the forward orientation of the leg cylinders. How do we know this? You might be surprised to learn that shield loading data may suggest otherwise. In addition, what about setting pressures? Should they be set as high as possible? Some people have advocated that setting pressures should equal the yield pressure. Does this make any sense? Is yielding a good or bad thing? These are some questions still worthy of investigation that are addressed in this paper. The first major change in gateroad support was the use of cable bolts to replace conventional wood cribbing particularly in Western mines. Standing support changed very little until the mid-1990s, when Strata Products1 introduced the Hercules and Propsetter supports in Eastern mines and Burrell Mining Products introduced the Can support in Western mines. Since then, there has been a dramatic increase in new roof support technologies for longwall gateroad support. Historically, standing support, including shield supports, have been designed based on a simplistic model requiring the support to have sufficient capacity to support the gravity loading of a perceived detached rock mass. This approach ignores the stiffness of the support and the resulting ground deformation that is known to be critical to roof stability. Recently, a new approach based on the ground reaction concept has been promoted by the National Institute for Occupational Safety and Health (NIOSH) to account for the interaction of the support with the rock mass behavior in achieving ground stability. In addition to gateroad support design, this concept has ramifications for shield capacities, setting pressures, and recovery room support design that challenge current practices in these areas. Although longwall mining has matured into the safest and most productive underground mining method used today, traditional concepts of roof support design and practice should still be evaluated and challenged. Ultimately, advancements in the science of ground control are made by recognizing deficiencies in current theories and thinking outside the box.

By Dr. T. L. F. Muller

INTRODUCTION During the past decade a wealth of knowledge has been acquired about the mechanisms and reactions responsible for the physical properties of metals. In the field of steels, in particular, research of a fundamental nature has enabled us to interpret mechanical properties such as hardness, brittleness, creep strength, etc., in terms of atomic interactions. So rapid has been the development of physical metallurgy in some fields that publications are often outdated by the time they appear in print. The development of new steel products has been rather empirical by nature in the past and only during the past few years have new products been "designed" in terms of known physico-metallurgical phenomena. However, although this is a great stride forward it should be added that the development of a commercially successful product is a far more complicated process. In addition to the physico-metallurgical background this requires consideration of factors such as low production cost, market research and probably most valuable of all, an interested end user to co-operate in the development. This paper deals rather briefly with three of the most recent developments in steels in Britain with which the author has had some association. The main purpose of this is to demonstrate how the improved properties of the new product are based upon established physico-metallurgical phenomena. Generally speaking a commercially successful product of the type described here offers similar properties to that of an existing product at lower cost or has improved properties or features such as greater ease of cold forming, at similar cost. ULTRA-FINE GRAIN STRUCTURAL STEELS The development of higher yield strength structural steels dates back over a considerable number of years and has led to a variety of types. The one described below contains niobium as a grain refiner in an otherwise conventional mild steel matrix. By controlled rolling in a strip mill considerably increased yield strengths are obtained. In Fig. 1 are shown somewhat diagrammatically the relative hardening effects of carbon and manganese on ferrite. It will be seen that strength is enhanced by the solid solution hardening effect of manganese and the pearlite content. An obvious limitation of high pearlite content is a lack of cold workability and weldability. Manganese has to be restricted to low levels for the same reasons. The two other mechanisms which are known to impart higher strength are precipitation hardening and grain refinement. Precipitation hardening is impractical in most cases for structural steels and it is therefore clear that only grain refinement remains as a potentially useful strengthening mechanism.

By C. Vipulanandan

With the aging infrastructure, there is a need to maintain and extend the service life of steel structures in general and steel piles in particular. Steel piles support not only vertical loads but also dynamic horizontal loads in onshore and offshore applications. In order to select the appropriate methods to repair corroded steel piles used in onshore and offshore application, corrosion mechanisms were investigated with the rate of corrosion in various environments. The corrosion rate of steel in soil, water and soil-water interface varied from 2 to 500 µm/year. Based on literature review and analyses, the repair methods can be broadly characterized as protective coating, electro-chemical methods, wrapping and encasement and partial replacement of steel. Also, methods to evaluate the repair materials and the repair configuration have been documented.

By Chunlin Chen

Nickel-sulfide minerals are normally associated with copper and iron sulfides and often contain a minor amount of valuable metals such as cobalt and detrimental impurities such as arsenic. Metal losses in slag vary from process to process during the pyrometallurgical production of nickel and, depend on the feed composition, slag chemistry and operating conditions. Maximiz the metal recovery is one of major considerations to optimize operating condition for nickel smelting/ converting processes. At the same time, the deportment of minor elements between various phases during nickel smelting is of great importance by smelter operators. The Multi-Phase Equilibrium (MPE) is a thermodynamic package developed by CSIRO for simulating reactions between phases in multi-component and multi-phase systems [1]. Over the years the capability of the MPE model has been extended to cover the behavior of a large number of elements in high temperature systems. The sulfide smelting module of the MPE, which covers the minor elements such as As, Bi, Sb, Pb, Se, Te, Sn, Co and Zn, is capable of modeling the deportment of major and minor elements between various phases during nickel smelting. In this article the application of the MPE model in modelling the nickel smelting process is presented. The modelling results on the majors and minors are compared with the plant data. The deportment behaviour of arsenic in nickel smelting was analysed and the impact of slag chemistry on slag properties was modelled. These results can assist process metallurgists in exploring the optimum fluxing strategy for smooth operation and the potential practices for improving arsenic removal.

By S. J. Page, W. R. Reed, J. A. Organiscak

NIOSH continues to conduct respirable dust control research for surface mine blasthole drilling operations. Research areas have included testing variables (shroud leakage area, drill deck cross-sectional area, shroud height, collector-to-bailing airflow ratio, etc.) that have the most impact on respirable dust control, development of a dust collector inlet hood, development of a dust collector dump point shroud, and testing of a small diameter water separating sub. This paper summarizes the results of the aforementioned research that has been completed. Additionally, past dust control research for drilling operations of both underground and surface mines completed by the U.S. Bureau of Mines, created in 1910 and incorporated into NIOSH in 1997, is reviewed.

By Stephen C. Tadolini, Thomas M. Barczak

A critical safety component for all underground mining is intrinsic and standing support systems. Specifically, tabular hardrock mining exploits a wide variety of deposits that require various methodologies to safely mine the ore material. Several new support systems have been developed in recent years for hard rock applications which have been modified or applied in a variety of ground control applications. These include prestressing devices, improved cribs, and free standing supports. Various standing support and prop-type systems have been designed for hardrock applications with seismic loading conditions to accept prestressing. The prestressing, using water-filled cells, creates an active load upon installation and is considered essential to maintain support during and after the blasting of the mine faces. Heavy seismic activity is also present in these mines and the prestressing units can provide some energy absorption capability to help preserve the integrity of the support. This paper presents an overview of these innovations in support technology.

By T. M. Williams

DURING the year just ended we have had three great fires in the mines in the Wilkes-Barre district. One at the Empire Colliery, one at the Prospect shaft, and the other at the Baltimore old mine. It is proposed in this paper to give a brief history of the fire at the Empire Colliery, and the methods employed in extinguishing it. The fire was first discovered breaking out in the air-stack, alongside what is known as the " Kidder Plane," about one o'clock on the morning of December 31st, 1873. Subsequently it was ascertained that the fire originated in the return airway somewhere near the steam boiler, located inside the mine, near the head of No. 5 slope. The coal from this slope was hoisted to the shaft gangway, at a point nearly four thousand feet distant from the foot of the shaft. As there were from four to five hundred mine cars hoisted per day from this slope the steam boilers were located at this place. The mines being of considerable extent required a large volume of pure air for ventilation, and no fan having been erected at this slope at the time, the heat from the boiler was made use of to assist ventilation, by conveying the return air from No. 5 slope into the large airway made from these boilers to the surface through the old "Kidder slope" to the stack where the fire was first discovered. The length of this slope or airway was about one thousand feet, with a sectional area of about sixty feet. The quantity of air passing through it must have been over sixty thousand cubic feet per minute

During the past Two years in reef gold mining, "indicators" have received great attention at the hands at the Victorian gold seekers. Many years ago, what was caned the" indicator lode," was struck in Ballarat East, on the course of which extremely rich deposits of gold were discovered but as to its being a .qeneral experience in reefs or leaders no one ever dreamed. Now, however, we find that these "indicators" are frequently to be met with, though they differ very much in different localities, making it, therefore, a difficult matter for other than a careful minel' to follow them. The necessity of following "indicators" for the purpose of developing gold is now recognized, and the policy of following them up has been attended with much success in this field. In the case of Messrs Shaw and Sons, at Wedderburn, those gentlemen began to work on an "indicator" here five years ago, and immediately thereafter more by accident than anything else they being at that time inexperienced as regards "indicators " came upon gold bearing quartz, which continued payable so long as the" indicator" aud the stone were in conjunction with each other, but as soon as they parted company the stone ceasedto be of any value then, by following the" indicator," as the latter intersected fresh bodies of stone they proved again more or less payable, until a fortnight or so ago the Messrs. Shaw turned out 4 tons of stone, which yielded £1,825, with also profitable workingup to the present moment. Where they are now working is a mile north of their original find thus proving that "indicators" travel considerable distances and have something to do with the gold deposits found in reefs. On the direct course of Shaw's "indicator," as high as hundreds of ozs to the ton was obtained from the stone but, just a few inches from either side in the same" leader," not a colour could be got. Whatever the cause-whether by electricity or some unknown force in nature-the gold is found on the course of these" indicators" and nowhere else, and-as each of the Victorian Government Geologists admit-their value to the gold-seeker as a means of leading to' gold cannot be over-estimated.

The May General Meeting of the Institute was held in Kelvin House, Johannesburg, on 21st May, 1969, at 4.30 p.m. Mr J. K. E. Douglas (Vice-President) was in the Chair. There were also present twenty-two Members, including Messrs F. P. Bath, M. Bareza, A. R. C. Fowler, D. M. Jamieson, C. M. Mavrocordatos, D. G. Maxwell and J. A. Nixon (Council Members), Messrs T. Davidson, G. L. Diering, E. T. Dunstan, D. E. H. French, K. Hodgson, O. A. E. Jackson, A. F. Lee, A. Louw, D. L. Starkey, R. K. Wheeler and M. Youngworth. Four Associate Members including Messrs D. Blair Hook and G. R. Still. One Student Mr N. A. Barcza. Thirteen Visitors, including Messrs S. H. Ash, D. L. G. Bayne, E. Bayne, S. Bell, W. S. Garrett, L. S. Gibbs, R. C. Hamilton, M. Maguire, D. Rose and J. D. van Niekerk. Total Present: Fourty-one. OBITUARY The Vice-President: "It is my sad duty to announce the death of the following member of the Institute: Thomas Spence Haldane, Member, who joined the Institute in 1924 and passed away on 21st December, 1968. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, those present stood and observed silence for a few moments. MINUTES The Vice-President requested that confirmation of the minutes of the previous meeting be held over as they would only be appearing in the Journal of the following month. He also requested that confirmation of the minutes of the 75th Anniversary Meeting be held over. MEMBERSHIP The Vice-President: "I have much pleasure in announcing that the names of the under-mentioned candidates have been published in accordance with By-Law 5.2.2, and Council has elected them to membership of the Institute in the following grades: Members: Gideon Jacob Haumann, Peter John Cumming, Ian Stanley Dudman, Roderick Goldston Murchison. Associate Members: Francois Alwyn Beyers Fouche, Alan Marsh, Johannes Petrus van der Westhuysen, Waldo Edmund Stumpf, Ian Nicholas Ridley. Affiliates: Lutgerus Kolver Jooste, Roger Ainsley Ralph Kebble, Edward John Wainwright, Lewis William Davies. Graduate: Clive Graham Knobbs. MEMBER TRANSFERED TO A HIGHER GRADE From Student to Associate Member: Diethard OUo Eduard Fahrbach. I welcome the newly elected members to the Institute and congratulate the member who has been transferred to a higher grade." (Applause).

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global plate-tectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20° in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed.

By Kymberley Worrell

The Cripple Creek and Victor Gold Mine was acquired by Newmont in August 2015. The high grade flotation mill project was commissioned in February 2014. The mill to date has been throughput limited due to mechanical and design issues. In order to create the most value from a throughput limited plant a campaign to provide timely ore characterization was undertaken. A diagnostic leach methodology was developed to determine gold associations by ore type. The resulting associations were then used to characterize feed blend; gold losses and optimize gold production. The diagnostic methodology is presented along with discussion on flotation implications.

By Edward L. McHugh

Digital camera and computer technologies can be used to monitor mine slopes and provide real-time warning of rock falls. NIOSH researchers assembled a surveillance system using low-cost video cameras and computer software from the security industry to test its effectiveness. The system is designed to signal an alarm when motion is detected and to record images of the scene. Masking can restrict motion detection to specific areas within the camera view; sensitivity is adjustable. The time-stamped images provide a record that can help reconstruct and quantify an event. Video motion detection can augment standard monitoring methods to increase safety in surface mines.

By W. F. Lorch

Growing use of deionised water in surface coating techniques by w. F. LORCH Production engineers in the metal plating, paint, plastics-coating and printed circuit industries are increasingly aware of the cost of sub-standard or blemished items which have been poorly processed. An area where quality control can quickly produce higher efficiencies is in the choice of suitably purified water for making up solutions, for rinse baths and 'drag-out' baths, for cleansing lines and electrophoresis tasks, for maintaining electrolyte density and hence consistency, and for facilitating the recovery of valuable minerals. The author of this article examines the general problems of using nonpurified water, and shows how purified water has become accepted by the principal surface coating industries to improve processes and effect economies.

By D. H. Henley, F. F. Craig, W. W. Owens

The oil recovery performance of systems producing entirely by bottom-water encroachment has been experimentally determined in a series of scaled laboratory-model tests. The effects of well spacing, fluid mobilities, rate of production, capillary and gravity forces, well penetration and well completion techniques on the oil recovery performance have been investigated. The laboratory tests were performed using two uniform, un-consolidated sand-pack models. The models have ratios of the interwell distance to the formation thickness of 12 and 2, respectively. Tests at constant total fluid production rate were performed simulating a range of uniform reservoir characteristics and operating conditions encountered in field operations. The performance was determined by material balance and by observation of the encroachment of dyed fluids into the models. The results of the model tests agreed with those obtained mathematically when the conditions previously considered in theoretical studies were simulated, that is, when the oil and water are of equal density and no capillary forces exist. The model study of bottom-water drive indicated that certain variables can aoect the oil recovery performance to a greater degree than can be predicted by present analytical methods. In one comparison, the oil recovery at a water-oil ratio of 20 (obtained at a wide well spacing) varied as much as threefold, depending upon the system's properties and the production rate. Lesser effect of mobility ratio and no eflect of capillary forces over the range studied were observed. The test 'results also showed that the deeper the well penetration into the oil column, the greater the total water production to a producing WOR of 20. However, the ultimate sweep efficiency, and so the oil recovery to this level of WOR, did not vary significantly with well penetration. Horizontal fractures at the top of the formation did not significantly change the sweep characteristics of the reservoir models when values of radius and fracture capacity encountered in actual reservoirs were used. Impermeable pancakes at the bottom of the well moderately increased the oil recovery efficiency both at water breakthrough and at high water-oil ratios. A method is outlined by which the oil recovery performance of other uniform bottom-water drive systems can be estimated from the information obtained in these model tests. INTRODUCTION When oil is produced from a well which partially penetrates an oil zone completely underlain by water, the water rises directly beneath the well in a symmetrical cone when the system is uniform. Two different flow mechanisms can cause the water cone to form—coning and bottom-water drive. In coning, the aquifer is relatively inactive and the cone is formed beneath the well by the pressure gradients associated with the oil flow to the well. The oil can be produced by a solution-gas drive, an edge-water drive or other driving forces in the interwell area. In a bottom-water drive, the driving force for oil production comes from an upward encroachment of the underlying active aquifer. Two papers have analyzed the theoretical performance characteristics of bottom-water drive reservoirs. In the initial mathematical investigation, Muskat' established the equations which determine the pressure distribution in this type of reservoir and solved these equations for certain conditions. Specifically, it was assumed that the water and oil had equal mobilities and equal densities, there were no capillary forces, the pressure throughout the oil zone remained above the bubble-point pressure, a constant pressure existed at the initial water-oil contact and the oil was completely displaced by the encroaching water. These assumptions were used in obtaining analytical solutions. In general, Muskat found that the sweep efficiency to initial water breakthrough to the well was larger for the thicker oil zones, the closer well spacings, the lower ratios of vertical to horizontal permeabilities, the smaller the penetration of the well into the oil zone and the smaller the bore size of the well. The production history after water breakthrough was expressed as a volumetric sweep efficiency at a given producing water-oil ratio. The results indicated that cumulative oil production at producing water-oil ratios of 10 is less affected by the well spacing than is the water-free production history. Muskat studied well spacing which today would be regarded as close. The maximum value of his dimensionless well spacing (ratio of interwell distance to formation thickness) was 4.3. This would require the development of a 50-ft-thick oil sand on less than 10-acre spacing if the vertical and horizontal permeabilities were equal, with

By D. R. Dolinar, A. T. Iannacchione

Limestone formations in the United States can be subject to relatively high horizontal stresses owing to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rock fall hazard. Rock falls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings has an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orienting the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and off-setting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

By Michael Johnston

Nautilus Minerals is exploring for high-grade gold, silver, copper, and zinc-rich submarine massive sulphide deposits (SMS) within the territorial waters of the sovereign state of Papua New Guinea. Work to date has shown that these systems contain spectacularly high metal grades. To date a total of 88 surface sulphide grab samples have been collected from Nautilus’ Solwara 1 Prospect within EL 1196 in the Manus Basin, returning average grades of 15.5 g/t gold, 191g/t silver, 10.8% copper, and 4.7% Zn. Drilling in January/February 2006 confirmed the presence of this high grade system, with sulphide intersections up to 19m below the sea floor, with a best intersection of 11.6m at 9.1 g/t Au and 13.1% Cu.

By John W. Pack

At present the manufacture of metallic zinc, or spelter, in Missouri, is carried on only at the establishments located at Carondelet, or South St. Louis. Although the development of the industry has not yet reached that fulness which it has attained elsewhere in the United States, still the commanding advantages of position of these establishments are so evident that the prospective importance and magnitude of spelter manufacture in this State, and especially at this locality, can hardly be doubted. A study of the chemical and technical aspects of the business of these points cannot be without interest to the metallurgist as well as to the capitalist. I have endeavored to investigate, as far as was practicable, within the limits of a paper of this character, some of the problems connected with this industry, at the same time making a few comparisons of the results attained at some of the Carondelet works with those of other establishments with regard to which information could be obtained. In the prosecution of these studies I have been kindly aided by the managers of Carondelet establishments, and by Prof. Charles P. Williams, Director of Rolla School of Mines. To the latter I am especially indebted for assistance in regard to methods of analysis. To all these gentlemen I return my thanks for their valuable aid. Other sources of information will be duly credited in their proper places.

By J. H. Henderson, R. J. Wygal, J. Naar

Experimental work is reported which shows that consolidated rocks and unconsolidated porous media exhibit different imbibition flow behavior. At a given saturation the imbibition nonwetting permeabilities for a rock are smaller than the drainage permeabilities. The contrary happens for unconsolidated aggregates — imbibition nonwetting permeabilities are larger than drainage ones. A similar difference is observed for the wetting phase. Imbibition permeabilities are larger than drainage ones for a consolidated rock but smaller than drainage permeabilities for an unconsolidated medium. The results of these differences are examined for two cases. 1. Flooding Efficiency — Craig's1 scheme for the computation of production history of a five-spot water flood is shown to agree extremely well with experimental results obtained when using a system packed with glass spheres if imbibition relative permeability curves are used. 2. Alcohol-Slug Displacement — Published theory 2 on oil displacement by alcohol slugs has been questioned despite the apparent agreement between predicted and observed results. The present work suggests that, if imbibition relative permeability curves characteristic of the unconsolidated media used in the early experiments had been available to make the predictions, the inadequacy of the theory would have been immediately evident. The experimental work shows that poorly consolidated formations tend to behave like unconsolidated media. Finally, it is shown that the difference in imbibition behavior is directly related to pore-size distribution and cementation. PART 1 — THE FLOW BEHAVIOR OF UNCONSOLIDATED AGGREGATES Experiments on scaled models of field reservoirs are useful for studying new displacement processes which are incompletely understood. Even when a mathematical description is possible, the solution might be difficult and complex. An answer obtained from a scaled model is extremely valuable in such cases. A great amount of work$-5 therefore, has been devoted to the derivation of scaling laws. Similarity groups have been defined which assume (1) that the relative Permeability curves of the prototype and the model are the same whether the displacement is an imbibition or a drainage process and (2) that there is a linear relationship between the capillary pressure of the model and the prototype. For practical reasons (simplicity in the preparation of models, duration of the experiments, etc.), the porous media of laboratory models are usually unconsolidated packs of sand or glass particles. Hence, unless the capillary and flow characteristics of unconsolidated and consolidated systems are identical, the model data are applicable only to unconsolidated formations. The usefulness of scaled-model studies may then be seriouslyrestricted since most oil-bearing sands are consolidated. Perkins and Collins6 suggested the use of model and prototype curves normalized with respect to both relative permeability and saturation to improve compliance with scaling criteria. Even this technique does not give a satisfactory model-prototype match. This paper reports an observation of two-phase flow in unconsolidated sands which shows that, for most displacements, "scaling" in the strict sense of the word is not even qualitatively feasible with a sand model. It provides, however, a firm foundation for testing a theory by matching it with observed performance of laboratory-size models. EXPERIMENTAL AS a part of a basic study of packed aggregates, the relative permeability of glass-spheres and sand-grain packs was measured with capillary control. The fluids were oil and air' The spheres were packed in plastic cylinders 1-in. in diameter;

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry and seal manufacturers, conducted a series of full-scale experiments within the underground experimental mine at PRL's Lake Lynn Laboratory. The purpose of the experiments was to evaluate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in less than 12 hours and are capable of withstanding explosion overpressures in excess of 140 kPa (20psi). These novel seal designs use available mine materials, do not require conventional rib hitching and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.