Search Documents

By Donald O. Rausch, Robert H. Merrill

12.1 -1. Introduction. Problems concerning slopes in soils and rock generally arise in connection with road cuts and open pit mines. The angle at which a slope will safely stand is of major economic importance to both the road designer and the open pit operator. Stable slopes in soils and rock are evaluated through two fundamental approaches, namely, soil mechanics and rock mechanics. The approach selected to make this evaluation depends upon the material in the slope. For the purposes of this chapter, only slopes totally in soil or totally in rock are considered. By definition, soils are unconsolidated accumulations of solid materials produced by mechanical and chemical disintegration of rocks or the accumulation of sediments (28); rock is defined as the hard, compact, natural materials composing the crust of the earth (10). The basic factors affecting slopes in soil or rock are similar, although rock strengths are orders of magnitude greater than soil strengths. In general, the strength of large masses of soil depends upon the texture of the soil, the particle size, cohesion, and resistance to tensile and shear stress; the strength of large masses of rock depends upon the strength of the rock and the defects, such as faults, fractures or joints, that intersect the rock. Further, some of the defects in rock are cemented or uncemented, and may be filled with materials that are strong or weak compared to the rock. In slopes of either soils or rock, the stability is presumed to be a function of the slope height, slope angle, the size of the excavation, and the stresses imposed on the soil or rock by tectonic and/or gravity forces, earthquakes, or other static or dynamic forces. In addition, both soil and rock slopes are affected by static and dynamic water pressures in the pores of soils or permeable rocks or in the defects in the rock behind the slope. Visual observations of slope failures also indicate that both soil and rock can deteriorate with time, and this deterioration may be caused primarily by weathering (27).

Jan 1, 1968

By W. A. Backofen, D. Lee

Tlze condition of superplasticity or neck-resistanl flow that results front high strain-rate sensitivity has been observed in isothermal tension tests on several titanium alloys and one of zirconium hi general, il was associated with reasonably fine-grain micro-structures being stvained in the transformation range at rates below i - 10 -3 sec-&apos;. The metallographic mean-free path, L, was measured at room temperature after rapid cooling from the temperature of test-ing. The flow stress of Ti-GAL-4V at 950°C was proportional to La at different constanl <; the value of a decreased with increasing. E but at E< 1.5 x 10-4 sec-1 it varied only from 0.9 to 1.25. The findings were interpreted to mean that viscous boundary shear is the rate-controlling process of deformation at high levels of strain rate sensitivity in these materials. Elongation of over 1000 pet could be obtained, but a1 temperatures so high and rates so low that any practical application of the full effect would probably be difficult. As the transformation range was narrowed, by turning from Ti-6AL-4V to Ti-5Al-2.5sn to nomznally pure titanium, the allowable temperature varialion was correspondingly reduced. Superplasticily was not found in Armco iron, presumably because the transformation range was too narrow to allow the developtnenl of a reasonably stable microstructure for isolhermal lesting. THE work represented by this paper grew out of a recent study of texture hardening in a(hcp) titanium and zirconium-alloy sheet,&apos; of which part has now been published.2 It was found that, with heating, the tensile plastic-anisotropy index, R,* was decreased from well above 1 towards 1 as the temperature range for the a(hcp) -ß(bcc) phase change was entered. The clearest example of that trend is illustrated with previously unpublished data in Fig. 1. It might have been thought that such a development resulted simply from introduction of the cubic and therefore plastically less anisotropic phase. However, the accompanying change in the index of tensile strain-rate sensitivity, m = a log a/a log E, was rapidly upwards, to a high of 0.85 in some cases (also illustrated in Fig. 1). At the same time, the total tensile elongation rose to a maximum and the flow strength dropped away as R (and m) approached 1. Taken together, the observations cannot be understood as resulting from the presence of cubic phase, per se. It has been concluded instead that they reflect the largely noncrystallographic deformation which characterizes superplasticity. As demonstrated in other recent work? a necessary condition for super-plasticity is strain-rate sensitivity of flow stress sufficiently high that m is above a lower limit of -0.3. The origin of large m has been traced, in turn, to grain size so small that a substantial amount of viscous deformation is introduced by such processes as Nabarro-Herring diffusional flow4 and/or grain boundary shear.5,6 Because of problems in the processing of titanium and zirconium alloys—problems of high strength, limited ductility, and excessive springback, originating largely in slip resistance-it was natural to wonder if something useful might be done with superplasticity in those materials. Therefore experiments were made for more closely identifying and generally bounding the phenomenon with temperature and strain-rate limits, before attempting to decide about its exploitation. The results are being reported here. EXPERIMENTAL Materials. The two of primary interest were the titanium alloys of nominal composition (in wt pct) 5A1-2.5Sn and 6A1-4V. Others were a 4A1-1/4O2 titanium alloy, titanium of commercial purity (RC-70), Zircaloy-4. and Armco iron. All were received as annealed 3/16 in. thick sheet, except RC-70 which was & in. thick, and tested in that condition. Details of transformation temperature and grain size are given in Table I. The results of dilatometry for the measurement of transformation temperatures were unsatisfactory. Data were finally obtained by metallographic examination of each specimen after test, to determine from the amount of transformed 4 where the specimen had been heated in relation to the critical temperatures. Results were in reasonable agreement with information from the supplier. Strip tensile specimens were of full sheet thickness and taken along the rolling direction, except for those

Jan 1, 1968

By Emerson F. Heald

A systematic study was made of new and old data on chemical activities in Fe-Pt alloys at elevated ternperatuves. Experimental results may be expressed in terms of the excess free energy using Least-squares analysis of the data gave the following values for the constants: for the temperature range 1130° to 1350°C, and tentatively to 155O°C, B = -3.326564 and C = 0.221051; for the temperature range 650" to 850°C, B = -2.555690, C = 1.762735, and D =0.097196. In the study of iron-containing silicate systems, it is sometimes desirable to have a direct experimental measure of the activity of iron in the system. The well-known solubility of iron in platinum, often a headache in experimental work on iron compounds under reducing conditions, can be used to advantage in this respect. If the activity of iron in an Fe-Pt alloy in equilibrium with the silicate is known as a function of the composition of the alloy, chemical analysis of the alloy will give a knowledge of the activity of iron in all of the phases in the system. The present study was undertaken in order to elucidate the characteristics of Fe-Pt alloys as iron activity indicators. This work is intended to tie together some previous work, which may be summarized as follows. Larson and Chipman1 determined the activity of iron in Fe-Pt alloys at 1550°C by equilibrating platinum metal with calcium oxide-iron oxide-silica melts of known iron activity. Compositions of the resulting alloys were determined by chemical analysis. A similar study was carried out by Taylor and ~uan,&apos; who worked at 1300°C. They brought the Fe-Pt alloys into equilibrium with iron oxide under conditions of known partial pressure of oxygen, and thus, from the work of Darken and ~urr~,~ conditions of known iron activity. Compositions were determined indirectly, by following the change in weight of the sample. Sundaresen et el* used the electromotive force of cells in which the alloy formed one electrode in order to measure the activity of iron in the alloy at 650" and 850°C. These temperatures were chosen to be above and below the first-order phase transition which takes place upon the ordering of Fe3Pt and the second-order transition which occurs upon the ordering of FePt3. EXPERIMENTAL 1) High Temperatures. The starting materials used were thin platinum foil, about 0.002 mm thick, and Fisher Certified reagent ferric oxide, Fez03, which had been heated for 24 hr at 1000°C. An intimate mixture of 80-mesh Fez03 and platinum platelets was placed in a thin platinum foil envelope. The latter was suspended from thin platinum wires in the hot zone of a vertical-tube, platinum-wound furnace of the type described by Muan and ~sborn.~ A capillary gas mixer similar to that used by Darken and Gurry3 was used to prepare a precisely known mixture of carbon dioxide and hydrogen, which was allowed to flow upward through the furnace tube. The partial pressure of oxygen in contact with the sample was thereby fixed at a value which was calculated from the charts prepared by porter? Temperatures were measured with a Pt-10 pct Rh-in-platinum thermocouple, which was calibrated using the melting points of gold (1062 .@C) and diopside, CaMgSizOB (1391.5"C). Temperature control was maintained to within i3"C with a Geophysical Laboratory proportional controller, using the furnace resistance as the sensing element. Samples were quenched by passing a small current through the platinum suspension wires, allowing the sample to drop into a bath of dibutyl phthalate at the bottom of the furnace tube. Prior to chemical analysis the samples were washed with acetone and dried. 2) Chemical Analysis. It proved possible, in almost all cases, to separate the Pt-Fe platelets physically from particles of iron oxide. The platelets were dissolved in a small volume of aqua regia, evaporated to dryness, and redissolved to 0.1 M HC1. In order to determine iron in the platinum alloy potentiometrically, it is necessary first to remove the platinum. A 10-cm column of Amberlite IR-120 cation exchange resin in the hydrogen form provided separation quickly and quantitatively: The mixture of iron and platinum in 0.1 M HC1 was added to the top of the column, and washed with about 100 ml of 0.1 M HC1. Under these conditions, the iron, principally in the form of cations such as FeC1" and FeCl;, is held quantitatively in the uppermost centimeter of the column. The platinum, in the form of anions such as PtC&- , is washed through without being adsorbed. After a qualitative test with stannous chloride indicated all of the platinum was removed, the iron was

Jan 1, 1968

By R. B. Adair, J. S. Browning

The Bureau of Mines conducted laboratory research to determine the applicability of heavy liquid separation to the evaluation of certain mica ores and plant products. After careful standardization of the particular mica ores and associated gangue, accurate analysis of muscovite content could be obtained from results of heavy liquid separation. Where applicable, the method should be particularly suited to the analysis of ores and control of plant operations wherein savings in time would be of considerable advantage. Specifically, there are many instances where a quick plant control method should enable the production of a more uniform grade of mica concentrate. The laboratory use of various heavy liquids for separating minerals of different specific gravities has been recognized for many years.1-8 Sink-float procedures have proven their utility as a rapid and moderately accurate means for determining the mineral content of ores, test products, and plant products in certain nonmetallic concentrating operations. A standard method of analysis for mica in ore samples has not been published or generally accepted by the mica industry. Recently, the U.S. Bureau of Mines investigated methods for analyzing mica by heavy liquid separation. This report has been prepared to make the methods available to others who may need simple, relatively rapid methods of determining the mica content of ores and plant products. The heavy liquid method of mica determination has recently been adopted by one of the major mica producers for evaluating exploration and mill control samples. DESCRIPTION OF THE ORES AND HEAVY LlQLllD The weathered mica pegmatite ores used in the investigation were obtained from commercial mica op erations in Alabama, Georgia, and North Carolina. The major mineral constituents of the ores were muscovite, quartz, kaolin, and minerals of the feldspar group. The ores also contained minor quantities of biotite, limonite, and tourmaline. A comparison of the specific gravities of the major constituents of the ores (muscovite 2.76 +, quartz 2.65, kaolin 2.61, and feldspar 2.57), indicates that an effective separation of muscovite from the other minerals can be made in heavy liquids at a specific

Jan 1, 1968

By Kenneth K. Humphreys, Joseph W. Leonard, Robert L. Llewellyn, William C. McCulloch

INTRODUCTION The particular field of application of machines utilizing air currents as the primary separating medium is in the cleaning of the fine sizes of bituminous coal. Approximately 25,400,000 tons of bituminous coal were cleaned by air machines during 1965. They have not found any application for cleaning anthracite. Since the development and introduction of the first successful commercial pneumatic oscillating machine for cleaning bituminous coal in 19 16, by the Sutton, Steele and Steele Co, Dallas, Texas, and the American Coal Cleaning Corporation, formerly of Welch, W. Va., seven other successful pneumatic coal-cleaning machines have been developed and introduced to the American coal-mining industry: 1. Peale Davis: "Pneumo-Gravity" machine. 2. Arms "Concentrator," oscillating table. 3. Hey1 and Patterson oscillating table. 4. "Stump Air-Flow," pulsating air jig. 5. "Super Airflow," pulsating air jig. 6. Ridge air jig. 7. Phillip air jig. While not all coals can be beneficiated by air washing, the air washing of coals that are easy to clean can be readily proved advantageous. Of all the preparation methods, pneumatic cleaning is the most acceptable from the standpoint of delivered Btu cost. This is based on the premise that a percent of moisture is just as detrimental as a percent of ash. The principle of dry concentration has never been determined with scientific accuracy. To the present time the study has been more of an art than a science. It is possible to forecast the results of wet concentration from a study of the washability characteristics of the raw coal but only after applying rule-of-thumb methods of interpretation to the specific gravity and size distribution can it be ascertained that the raw coal is amenable to dry concentration. Air as a separating medium dates back to biblical times as exemplified in the winnowing of chaff from the grain. However, the same application of air to coal serves merely to blow the dust away and size the remaining particles. Pulsating air was the solution to the problem and largely eliminated the necessity for close screen sizing which was required on early separators. Because of the low density of air, a medium of sufficient density has to be built with the material itself. Hence there must be some device to impart to the bed the necessary mobility for proper classification. Also, the

Jan 1, 1968

By R. H. Tien

This paper presents an analytical solution of the problem of freezing of a semi-infinite slab with constant surface temperature; in this analysis accoz~nt is taken of the heat evolution during the solid-state transformations in the frozen skin. The regions where transformations occur are treated as plane isothermal heat sources; i.e., the rates of transformations are assumed to be infinite. In the model considered, three plane heat sources are assumed to be present in the frozen solid. The solution yields the temperature distribution in the solid, the rates of movement of the heat sources , and the rate of movement of the solidification front. It is shown that, although the sum of the heats of transformations in the solid is about 20 or 43 pct of the heat of fusion of iron or manganese, respectively, the effect of the heat evolution in solid-state transformations on the rate of solidification is insignzficant. IN several recent mathematical studies of solidification of liquid metals&apos;-3 no account was taken of the heat evolution accompanying the solid-state transformations. In the case of, for example, steel, there are several phase transformations 6 -y, y -a, and the magnetic transformation. Whether or not a significant error is introduced into the mathematical simulation of solidification processes by the omission of the heat effects associated with these phase transformations is not known. The purpose of the present study is to investigate the effect of these phase transformations on the temperature distribution and the rate of solidification based solely on the heat transfer point of view. That is, for the sake of simplicity, freezing of a pure metal with solid-state transformations will be considered. The mathematical model which represents the present problem includes four moving heat sources representing freezing and phase transformations, 6— y — a — ferromagnetic. The thermal properties such as conductivity and specific heat, and so forth, are different from one phase to the other. But they are considered to be uniform over any particular phase. The usual Fourier heat flow law is employed. The concept of conservation of energy is applied at every heat source in order to estimate their rate of movement. The temperature distribution in the solid and the positions where transformations occur are expressed analytically in terms of error function solutions and four coefficients which are determined from four nonlinear algebraic equations. These coefficients can be calculated either by trial and error or by any numerical method. MATHEMATICAL ANALYSIS Fig. 1 is a schematic diagram showing the zones of different phases 1, 2, 3, and 4 in the solidified portion of a semi-infinite pure liquid metal. The heat is subtracted from the system at x = 0 which is maintained

Jan 1, 1968

By B. A. Cheadle, K. P. Steward

Axial tensile, ring tensile, closed end burst, and free end burst tests were done at room tempe.vature and 300°C on three batches of Zircaloy-2 sheathing zuith different textures. Knoop hardness tests were also done on all batches. The mechanical properties of the tubes were largely dependent on the percentages of cold work, but were also markedly affected by the textures, particularly with respect to deformation behavio&apos;r. The deformation behavior observed confirmed Picklesimer&apos;s predictions, zuhereas Knoop hardness results could be correlated with texture and yield strength anisotropy after the ,method of Wheeler and Ireland. From the mechanical properties, and from efjectiue strain values deterrlzined at the fractures using a photoqid technique, it zuas concluded that tubing witlz a single preferred orientation of radial basal poles best combines strength and ductility for any given deqee of cold work. THE mechanical properties required in collapsible Zircaloy-2 fuel sheathing for water-cooled power reactors are strength to resist wrinkling deformation by coolant pressure and ductility to accommodate a small amount of deformation in service without rupturing. Zircaloy-2 tubing during fabrication develops pre- ferred orientations of the a Zr grains due to aniso-tropic deformation behavior, and these textures markedly affect mechanical properties. Picklesimer&apos; had predicted the deformation behavior of tubes with various textures, but the texture required to provide the optimum strength and ductility for a given degree of cold work has not been reported. To investigate this problem, tests at three transverse to axial stress ratios were done at room temperature and 300°C on three batches of Zircaloy-2 tubing covering a wide range of textures and percentages of residual cold work. Knoop hardness values were also measured to correlate with preferred orientation and yield strength anisotropy after the method of Wheeler and relland.&apos; 1) MATERIAL For this investigation, three batches of tube-reduced tubing were chosen from the Zircaloy-2 sheathing produced for the Douglas Point Reactor. Individual tubes were 191/2 in. long, 0.600 in. OD, and 0.0165 in. nominal wall thickness. The identities of the batches, together with their textures, are shown in Table I. The tubes had the normal Zircaloy-2 composition3 of 1.5 wt pct Sn, 0.3 wt pct Fe, Ni, Cr combined with the following oxygen concentrations: Batch VII 1140 to 1390 ppm 0 Batch VIII 1400 to 1750 ppm 0 Batch IX 880 to 1320 ppm 0

Jan 1, 1968

By J. A. Elias, A. J. Heckler

A simplified method is described for the prepauatior~ of comnposite samples for determination of one quadrant of an X-ray pole figure of a sheet material by the Schulz reflection method. Other special conzposite sampling methods were used to investigate specific areas of the pole figures. Plotting nets for these sampling plans were drawn by a computer. Step-scanning techniques were used to obtain detailed information about specific regions of a pole figure. Satisfactory pole figures were obtained for large-grained (0.5 to 1 in. diam) sheet materials. COMPOSITE sampling techniques for preparing one quadrant of an X-ray pole figure have been reported by a number of authors.&apos;-5 All of these methods are similar in that they use a composite sample prepared by stacking and holding together coupons cut from a sheet material. The schulze reflection technique is applicable to the composite sample so that only minor corrections are needed for defocusing and absorption effects. Also, a relatively large area of a sheet is sampled through the use of multiple cross sectional pieces. In general, sampling methods necessary to obtain a composite-type specimen have been formidable enough to discourage their use in routine pole figure determinations. This paper presents a versatile sampling technique which is simpler than those previously described along with an accurate method for obtaining stereographic plotting nets for any orientation of a composite specimen surface. A step-scanning technique is used to obtain more quantitative determinations of specific regions in pole figures, and the composite technique is satisfactorily applied to determine pole figures of very large grained sheet materials. REVIEW OF PREVIOUS TECHNIQUES Mueller and ~nott&apos; first proposed a technique for obtaining one complete quadrant of an X-ray pole figure by using a sheet sample and six different composite samples in which the individual coupons were aligned and held together by two types of jigs. Data from the seven different samples were overlapped to obtain a single quadrant. ~eieran~ and Lopata and ~ula~ obtained a complete quadrant of a pole figure from a single sample prepared by forming a cube from coupons cut from a sheet. These coupons were bonded together using an epoxy cement, and a cut was made at 54.7 deg to the normal, transverse, and rolling directions of the sheet, Fig. I. The normal direction of the cut face projects into one quadrant of a stereographic projection at equal angles to the three principal orthogonal reference directions mentioned above. X-ray reflection data obtained along a spiral path in physical space could then be plotted on a stereographic net offset 54.7 deg from the normal, as shown in Fig. 2. A rotation about an axis representing the surface normal is designated as a, and a rotation about an axis lying in the plane of the surface is 4. From Fig. 2 it is apparent that a tilting angle of no more than 55 deg @ is necessary to obtain the complete quadrant. ~eber~ devised an improved sampling technique by cutting coupons 45 deg to the rolling direction of a sheet, stacking and bonding these with an epoxy cement at an angle of 54.7 deg to a reference plane, and finally grinding and lapping a flat specimen surface parallel to this plane. An important consideration of this technique and that of Lopata and ~ula~ is variation in the diffracting power of the specimen surface due to the bonding medium. While any composite-type sample will have some such variation due to boundaries between coupons, the problem can be minimized by elimination of the bonding medium and by avoiding prolonged etching times which could lead to significant inter lame llar attack of the coupon faces. EXPERIMENTAL TECHNIQUE We were working concurrently though independently on a technique similar to ~eber&apos;s,&apos; but which does not

Jan 1, 1968

By D. P. Caplice

On behalf of the Ontario Water Resources Commission, I would like to express my sincere appreciation to your Institute for presenting us with this opportunity to outline the regulatory control programme as it relates to the mining industry in the Province of Ontario. In Canada, and particularly in Ontario, we are blessed with an abundance of natural resources. Fresh water in the form of lakes and rivers covers nearly 17 per cent of the area of the Province. (Total area of the Province of Ontario is 412,582 square miles.) The mining industry, which had its beginning in the early 1800&apos;s with a small iron ore plant, has progressed with the major discoveries of nickel and copper in 1883, silver in 1903, gold in 1908, iron in 1939 and uranium in 1953, to the point where, in 1966, almost one billion dollars in mineral wealth was mined in Ontario. Water, in spite of its great abundance and with due respects that it may become a natural resource worthy of export in the foreseeable future, has become increasingly precious in Ontario, particularly in the more urban areas in the southern part of the Province.

Jan 1, 1968

By John Ward Smith

Oil-yield data are presented for core samples from Colorado Corehole No.1, drilled by the Bureau of Mines and the Atomic Energy Commission in a previously untested oil-shale area near the northern edge of Colorado&apos;s Piceance Creek Basin. Continuous oil shale 2068 feet thick, averaging 18.41 gallons of oil per ton of shale and representing 1.8 billion barrels of oil per square mile, occurs at the core site.

Jan 1, 1968

By R. G. Peluso

Methods and results of studies to determine friction and shock losses encountered in auxiliary face ventilation systems utilizing flexible, spiral-reinforced ventilation tubing are presented. The results, tabulated in graphic form, simplify fan selection and enable mine operators to design adequate auxiliary ventilation systems. Problem illustrates the use of graphs.

Jan 1, 1968

By J. H. Anderson, G. A. Parks, B. K. Jindal, H. Leslie Bullock

H. Leslie Bullock (Engineering Consultant, Oak Park, 111.) — In reading over the paper, I find that I have no quarrel with the thoroughness of investigation of the points studied, but I am forced to question the selection of oxides from oxides as the subject of the investigation, the inclusion of silica gel as an example, and to question the validity of some of the conclusions. Separation of oxides from oxide, in minerals where the liberation of values is possible by grinding, are comparatively rare. Most oxides are only slightly soluble and the action of carbon dioxide or other acid forming ingredient in the air must be added to humidity to produce surface action. Silica gel is a very special synthetic substance in which the adsorption is determined by total surface, pore dimensions and temperature. Quartz is our most prevalent oxide and its action in electrostatic separation is far more sensitive to its three thermal transition points than to humidity.

Jan 1, 1968

By Steve H. Carpenter, Henry E. Otto

The explosive welding of metals is dependent upon the production of a jetting action caused by the collapsing of one metal plate against another. Successful welds are generally accomplished if the yield strength of the metals is in the range of 10,000 to 90,000 psi and the sonic velocity of the metal is greater than the detonation velocity of the explosive if direct contact explosive is being used.&apos; Should the detonation velocity exceed the velocity of sound in the metal it may still be possible to obtain the jetting action and a good weld. However, in most cases where a high detonation velocity is used complications arise because of reflected shock waves which tear the bond apart as fast as it is put together.&apos; Explosive welding of lead presents several problems since its yield strength and sound velocity are very low. Various values have been published3-5 for the velocity of sound in lead ranging from 2000~ to 23004 m per sec. Most of the high-order explosives have detonation velocities on the order of 6000 to 8000 m per sec, which precludes their use. The dynamites have a lower detonation velocity of around 2800 m per sec which is still somewhat too high. Lower-order explosives such as ammonium nitrate (1070 m per sec) must be used to weld lead in the as-received condition if the explosives are used in direct contact. Rather than use low-order explo&apos;sives it was decided to alter the sonic velocity of the lead. The sonic velocity is directly related to the modulus of the material according to the following expression: Fig 1—Interface of explosive weld of lead to steel. Lead is on top As-polished Magnification 75 times as well as the yield strength. Bolling et al. 6 show that the shear modulus of lead single crystals increases from about 0.72 X1011 dynes per sq cm at 300°K to about 0.98 X1011 dynes per sq cm at 0°K, an increase of approximately 3 5 pct. This gives an increase in the sonic velocity of around 700 m per sec. Hence, the sonic velocity of lead at cryogenic temperatures is approximately equivalent to the detonation velocity of the low-order dynamites. We have obtained high-quality lead to steel explosive welds using a 40 pct dynamite in direct contact with the lead. Prior to detonation the lead was chilled with liquid nitrogen (78°K) to increase the strength and sonic velocity. Welds were made while the lead was cold. Specimen sizes were 3 by 6 in. A preset angle of 5 deg with a 0.10-in. standoff at the base was the geometrical setup used. The amount of explosive used for optimum welding of an 1/8 -in. -thick lead sheet to a steel plate was found to be 7 g per sq in. A PETN sheet explosive line wave generator was used to insure a linear detonation front through the dynamite. A photomicrograph of a lead-steel weld is shown in Fig. 1. The typical wave effect that constitutes a good explosive weld is present. When tested in shear, the weld failed in the lead, indicating that the bond is stronger than the lead base metal. Higher-order explosives were also tried without success. We believe this indicates the importance of matching the detonation velocity and the sonic velocity for successful explosive welding. Note Added in Proof. High quality explosive welds of lead to steel have recently been obtained at ambient temperature using a low velocity (1000 M per sec) free running dynamite. The weld interface obtained is comparable to Fig. 1. &apos;S. H. Carpenter, R. H. Wittman, and R. J. Carlson: Proceedings of the First International Conference of the Center for High Energy Forming, Syracuse University Press, syracu.se, N. Y., in press. &apos;A. HI Holtzman and G. R. Cowan: Welding Risearch. Council Bull., No. 104, April, 1965. &apos;Metals Handbook, 8 ed., p. 1062, Metals Park, Ohlo. &apos;J. M. Walsh, M. H. Rice, R. G. McQueen, and F. L. Yarger: Phys. Rev., 1957, vol. 108, pp. 196-216; &apos;L. V. Al&apos;tshuler, K. K. Krupnikov, B. N. Ledener, V. I. Zuchikhin,

Jan 1, 1968

By Edwin M. Murphy

Methods are described for filling underground cavities remotely with dry material pneumatically injected through a borehole to seal openings, prevent air movement, and reduce subsidence; this often brings underground fires under control by limiting the access of air. Large-scale tests were made in the Bureau of Mines Experimental Coal Mine, Bruceton, Pa., in an operating mine, and in an abandoned Pennsylvania mine. Supplemental trials were made aboveground in galleries and in the laboratory. The parameters studied include horizontal and inclined passageways, obstructions in the entry, water leakage into the borehole, dry material, and grout and slurry mixes. The materials studied were fly ash, crushed and pulverized limestone, and sand. Best results were obtained with dry fly ash, though satisfactory seals were obtained with the other materials. When a borehole is dry and ends at an open void, casing is not necessary. If more than 5 gpm of water flows in the borehole, if the void contains loose debris, or if coarse material is injected, a material feedpipe should be inserted through the borehole. Fly ash was most suitable for remote filling because of its low angle of repose (8°) and its good flow characteristics. The depth of borehole through which the fly ash is injected has no appreciable effect on the filling operation.

Jan 1, 1968

By J. S. Redpath, W. R. Dengler

"A description of the equipment used and the electrical-mechanical problems encountered in sinking a deep shaft is given. This shaft is currently being sunk to a depth of 7,115 feet. Some of the features of the sinking plant are a 6,500-hp double-drum hoist, a Blair stage hoist, special high-capacity mucking gear, a Galloway stage, high-tensile stage suspension ropes and 12-ton sinking buckets.INTRODUCTIONIN THE EARLY FALL OF 1965, a contract was let, by The International Nickel Company of Canada, Limited, to Shaft Sinkers (Canada) Limited -J. S. Redpath Limited -Joint Venture, • to sink and equip the Creighton No. 9 shaft at their Creighton Mine proper-ty in Ontario. This paper describes the electrical and mechanical equipment used by the contractor on this project, and details various problems that were en-countered.The shaft itself is circular in section and is lined with monolithic concrete. Upon completion, it will feature twin skip compartments, a cage compartment, counterweight compartment, manway and pipe compartment. The finished diameter of this opening will be 21 feet and the shaft will bottom 7,115 feet below the collar. The present depth of the shaft (April, 1968) is 5,400 feet. The opening is concrete lined as excavation takes place and the steel will be placed in the shaft upon completion of sinking. Hoisting is done on rope guides which are part of the stage suspension system."

Jan 1, 1968

By Everett D. Jackson

The largest deposits of chromite in the United States occur in tabular layers in the lower part of the Stillwater Complex, Montana. Nearly 900,000 long tons of chromite concentrates have been produced from mines and mills in this area, and reserves equivalent to more than 2,500,000 long tons of Cr2O3 remain in the ground. Layered concentrations of chromite (known as chromitite zones) occur only within olivine-rich layers of the Peridotite member of the Ultramafic zone of the Stillwater. As many as thirteen chromitite zones, lying conformably one above another, have been found, but only five of them are thick enough to be of any conceivable economic interest, and only two of them have been mined to date. Individual chromitite zones can be recognized by their distinctive internal character and by their stratigraphic position in the Peridotite member. The chemical composition of chromite varies consistently between and within the different chromitite zones. The zones range in thickness from about an inch to more than 12 feet, and the Cr2O3, content of their chromite ranges from 36.6 to 49.2 weight per cent. In any given area, the G chromitite zone is the thickest, but the chromite of the H chromitite zone has the highest grade. Laterally, the thickness of the chromitite zones is related to the thickness of the Peridotite member; in general all are thicker in the eastern part of the Stillwater than in the western part.

Jan 1, 1968

By D. R. Derry

"IT WOULD TAKE a braver man than I to try to forecast the future of mining exploration far into Canada's second century. Even to look ahead ten or twenty-five years we must review the figures of the fairly recent past -and I have found this quite a time-consuming but interesting job -in order to find trends and project them into future years. The trends to which I will refer are: firstly, the annual expenditure on exploration and its relation to value of output; secondly, the discovery rate and its relation to production initiations; and thirdly, the methods by which discoveries have been, and will be, made. Exploration Expenditures Figures on the annual expenditure on mining exploration in Canada have been collected and published for some years by the Do-minion Bureau of Statistics. These have some unavoidable limitations; e.g., in the varying definition between one company and another of what comprises ""Exploration"" and in the difficulty of getting complete returns. However, although the actual figure for a given year may be subject to question, I believe that the relative figures from one year to another are reasonably reliable. There is also a lapse of time between the collection of data and publication -the last published figures are for the year 1963. In bringing the figures up to date to 1966 I have canvassed eight of the larger mining and exploration companies and obtained their figures for 1963 to 1966 inclusive, and then averaged these for each year and applied the progression to the 1963 figures."

Jan 1, 1968

By R. L. de Beauchamp

A preliminary investigation was made of the extraction of chromium from ferrochromium by low-temperature chlorination in the 3400 to 5250 C range. The objective was to devise a method for separating chromium from iron in high-carbon ferrochromium produced from domestic chromite concentrates. The majority of iron was removed as a volatile chloride; chromium was contained in the residue as a nonvolatile chloride, which was separated from carbon and unattacked ferrochromium by dissolution. A small rotary chlorination apparatus was designed, built, and used for the chlorination tests, and samples of commercial-grade high-and low-carbon ferrochromiums were chlorinated for comparison of chlorination characteristics. Low-temperature chlorination of three types of ferrochromium resulted in the removal of 81.9 to 91.6 percent of the iron content as sublimed FeC13. Recovery of chromium in a leach solution of the reactor product varied from 82.4 to 93.1 percent.

Jan 1, 1968

By R. Taggart, R. H. Ericksen, D. H. Polonis

MarTENSITIC a has been observed to form spontaneously from the retained ß phase during the preparation of thin foil specimens of metastable Ti-Cr alloys containing from 6.9 to 20 wt pet Cr. Similar spontaneous martensite reactions have been reported in thin foils of 0 brass&apos; and other alloys.2 4 The absence of retained austenite in iron-based alloys has also been attributed to spontaneous decomposition during thinning.5 The present work indicates that a unique situation occurs during which the spontaneous transformation takes place when the transitional ? phase is present in the as-quenched or partially aged ß phase. Alloys containing 6.9, 7.0, 8.0, 12.0, and 20.0 wt pet Cr were prepared by the levitation melting of "io-chrome" chromium and iodide titanium. The 0.5-in.-diam ingots were vacuum-annealed at 1000oC, and wafers 0.020 in. thick were then cut from the ingots. These wafers were wrapped in molybdenum foil, encapsulated in Vycor under a reduced pressure of purified helium, and then held for 30 min at 1000°C. The specimens were quenched in water to retain the metastable high-temperature ß phase. The quenched alloys were thinned by mechanical grinding to about 0.005 in. thick, then electropolished in a solution of 300 ml methyl alcohol, 175 ml n-butyl alcohol, and 30 ml perchloric acid at a temperature of -40°C. Needle specimens 0.005 to 0.010 in. diam were taken from each ingot and heat-treated with the foil specimens. X-ray diffraction patterns indicated the structure of the 6.9, 7.0, and 8 wt pet alloys to be a

Jan 1, 1968

By D. J. Bauer

Oxidation of mixed lanthanide solutions with ozone at pH 4.5 and at ambient temperature resulted in precipitation of 98 percent of the original cerium present. Corresponding cerium purity was increased from 50 to 98 percent. A second ozone oxidation-precipitation step produced cerium of 99.9 percent purity in high yield from the 98-percent-pure material. Alternately, ozonation at pH 6.5 and 85° C differentially precipitated cerium and rare-earth elements heavier than cerium and left 89 percent of the original lanthanum in solution at a purity of 95 percent. Subsequent recovery of cerium from the heavier rare-earth elements in the precipitate was accomplished by dissolving the precipitate in dilute mineral acid and reoxidizing the cerium with ozone at pH 4.5 and at ambient temperature. The filtrate contained an enriched praseodymium-neodymium-samarium-europium mixture that is amenable to separation by ion exchange or solvent extraction.

Jan 1, 1968