Search Documents

By C. L. Klingman

The Bureau of Mines tested eight commercially available, activated charcoals experimentally to compare the following characteristics: capacity for adsorption of nitrogen at 77° K and 170 atmospheres' pressure, surface area, carbon tetrachloride adsorption capacity, hardness, and density. The nitrogen adsorption test was devised to simulate plant conditions occurring in the final step of purification in Bureau helium faciliti.es. The remaining tests were patterned after empirical acceptance tests that are widely used throughout the adsorbent industry. Surface area and carbon tetrachloride adsorption correlated well with nitrogen adsorption. The samples with low density generally had better adsorption qualities than those of higher density. The carbon tetrachloride test appeared to be the most practical for selecting a charcoal to be purchased, but an attrition, or hardness test should also be run to be sure the charcoal will not crumble in use.

Jan 1, 1966

By R. Barany

The heats of formation of seven substances were determined by solution calorimetry. At 298.15° K, the heat of formation of lithium sulfate from lithium, rhombic sulfur, and oxygen was -343.1 ± 0.7 kcal/mole, and the heat of formation of lithium sulfate monohydrate from lithium, rhombic sulfur, oxy-gen, and hydrogen was -414.3 ± 0.7 kcal/mo1e. For the silicates, the heats of formation at 298.15° K from the elements were kaliophilite, -503.8 ± 0.5 kcal/mole; leucite, -721.6 ± 0,8 kcal/mole; eucryptite, -505,2 ± 0.6 kcal/mole; alpha-spodumene, -727.9 ± 0.9 kcal/mole; and beta-spodumene, -721.1 ± 0.9 kcal/mole. The corresponding heats of formation at 298.15° K from the constituent oxides were kaliophilite, -42.7 ± 1.1 kca1/mole; leucite, -42.8 ± 1.1 kcal/mole; eucryptite, -16.1 ± 0.7 kcal/mole; alpha-spodumene, -21.0 ± 0.7 kcal/mo1e; and beta-spodumene, -14.3 ± 0.7 kcal/mo1e.

Jan 1, 1966

By Lawrence F. Rooney

The wide distribution of limestone and dolomite and the decentralization of the depedent industries give the State Geological Survey a major role in the, development of these mineral resources. The amount of geological information necessary for efficient exploration is so large that few companies can afford to do the necessary basic field work or store the data. The state surveys fill these responsibilities and thus might be said to serve as the geological research departments of the limestone and dolomite industry. At the Indiana Geological Survey, the data of most value to limestone producers are in the form of unpublished measured sections, well records, cores, chemical analyses, directories, and geologic maps. Much of this information is published in summary form. The Survey also assists individual members of industry in exploration and evaluation of mineral deposits. In addition, a progressive State Survey provides the geological infor¬mation necessary for the development of new resources which do not appear to justify industry's own preliminary efforts.

Jan 1, 1966

By Thomas B. Dellinger

Since 1950, rotary-drilled, large-diameter holes, "big holes", with depths to over 300 feet and diameters of over 30 inches have become numerous and widespread. Fifty such holes have been drilled for access shafts to LPG mined caverns, Over 70 holes have been drilled for various other commercial activities. Over 150 holes have been drilled by the AEC for atomic testing purposes. These holes have ranged up to 300-inch diameters with 1600-foot depths, 120-inch diameters with 570-foot depths, and 72-inch diameters with 4800-foot depths. Equipment is now available to drill a wide range of ?big holes? for varied requirements. At least a dozen drilling contractors are participating or have participated in the drilling of "big holes". The accompanying tables show pertinent historical, technical and economic data on over 250 holes. The illustrations to be presented concurrently with this paper show the various equipment and accessories now in use. (See Appendix I for captions of illustrations.)

Jan 1, 1966

By D. E. Hawk, R. F. Burdyn, F. D. Patchen

Earlier work on a mud separator for barite recovery is extended to the design and construct ion of a rugged field unit. Problems associated with scale-up for field use include the me of dilution water and its effect on capacity, power requirements and pressures developed. Equations for these quantities are derived and applied in maximizing the beneficial effects of dilution and minimizing the power required. Tests on the full-size rotor show that its performance can be predicted by theory. The completed unit is compact and lighter than current decanting types. Its capacity is from 10 to 22 gal/min with corresponding barite recovery efficiencies of 92 to 86 per cent. INTRODUC'TION In an earlier publication a new type of centrifugal device was described for solid-liquid separations.l In that paper an operating equation was derived, and its validity demonstrated in laboratory scale experimentation. Some of the features apparent in this new device seem particularly well suited to the conservation of barite in field drilling-mud systems, hence the development was extended to the design and construction of a field unit. In the present paper the design problems associated with scale-up are considered. A full-scale, rugged self-contained field unit is described, and test results discussed which verify that the performance of the large field unit can be described by a simple operating equation. PRINCIPLE OF OPERATION OF SEPARATOR In principle, the new device is simply a perforated cylinder rotating within a body of fluid which is contained within a stationary case, as in Fig. 1. The frictional drag generated by the rotating cylinder causes part of the fluid to rotate. At the surface of the cylinder, assuming no slip occurs, the angular velocity of fluid and of the cylinder are identical. If there are suspended particles present of greater density than the fluid, the centrifugal force acting on these particles causes them to move radially away from the cylinder at some velocity vp . Where the Stokes settling equation holds, this velocity may be expressed as:2 d2 ?p rw2 If the case is provided with openings at both ends, a suspension can be pumped in at one end at a fixed rate. Part of the suspension can then be removed at a fixed rate at the other end of the case as underflow, and the remainder forced through the perforations and hollow shaft of the rotor to appear as effluent, also at a fixed rate. The radial component of the flow velocity of this stream as it reaches the rotor surface, is simply effluent flow rate divided by cylindrical surface area: Because up is a function of particle size, for some particular particle size, the velocities vp and v, will be equal in magnitude. This is defined as the critical particle size and represents the size above which all particles appear in the underflow and below which all particles appear in the effluent. For this equilibrium condition at the rotor surface, Eqs. 1 and 2 combined give

Jan 1, 1966

By P. Kostuik

"Recent interest in the pipeline transport of solid mate-als has been sparked by the idea that, in an inflationary onomy, pipeline costs are more stable than the costs of any other transport systems. Pipelines have proved over 1e years to be dependable, records indicate that main-•nance and operating costs are comparatively low, and 1eir amenability to automation is of considerable im->rtance.The concept of hydraulic hoisting of solids from under-round, or cross-country hydraulic transportation of con-~ntrates and ores, is currently of prime interest to the ining industry. In general, this paper deals with a preliminary investi-ation of energy losses incurred while transporting a rela-vely heavy, crushed mine product, namely magnetite, oth vertically and horizontally. The basis and validity of everal equations derived by other experimenters to com-ute these losses is discussed. A theoretical analysis of ydraulic hoi:,,ting is made, and, based upon test results, calculation of horsepower requirements for hoisting an re under a given set of conditions is presented. Results indicate that:n vertical transport, the friction head losses are identical to those of clear water, and the total energy requirement for hydraulic hoisting then becomes a function of height of lift, concentration and specific gravity of the solids being hoisted. .-In horizontal transport, friction head losses can be calculated with reasonable accuracy using Bonning-ton's correlation curve. Losses computed utilizing Durand's correlation (K = 85) result in estimates which are too low by 10 to 30 per cent, an<l those calculated using Newitt's correlation (K = 1,100, K = 66) give friction loss values which are too high by 10 to 30 per cent . . -The theoretical horsepower (RMS-hp.) required for hoisting hydraulically is approximately half of that required for conventional double-drum skip hoisting."

Jan 1, 1966

By Harry G. Hedgepeth

Exploration of the Big Island trona beds by Stauffer Chemical Company started early in 1959. During the intervening time, Stauffer Chemical Company of Wyoming has developed a Large trona mine in this southwestern Wyoming area and has increased the over-all production of soda ash from natural sources by nearly one-half million tons per year. The trona, which is a hydrated sodium bicarbonate mineral, lies some 800 feet into the sedimentary rocks of the Green River formation. Present production is approximately 850,000 tons per year being extracted by means of a room-and-pillar mining system. Conventional coal mining equipment is used with some modification to accommodate local conditions. The mined and crushed ore is hoisted to the surface and processed in an on-site refinery. Refined soda ash is shipped to widely separated locations in covered hopper railraod cars. Construction in progress at Stauffer&apos;s plant will double the present capacity.

Jan 1, 1966

By Lippe D. Sadwin

A high-speed streak camera method for making equation of state measurements (shock and particle velocities) on samples of rock under dynamic load conditions is described. Experimental data are given for tests on 12 samples representing 5 rock types. Analysis of these data shows that the method is practical and that good reproducibility of results can be obtained. The pressure range covered in the tests was from 1 to 50 kilobars.

Jan 1, 1966

By James E. Brewer

Procedure for approval by the U. S. Army Corps of Engineers of a new source of aggregate is in three phases. Phase 1 consists of an investigation of a quarry or proposed quarry by district geologist and laboratory geologist and/or petrographer. The quarry face or suitable outcrop is logged in detail or, if exposures are poor, cores may be taken to determine whether further investigations are warranted. Phase 2 consists of thorough laboratory testing. Cores and crushed material are subjected to a number of acceptance and quality tests for soundness, absorption, abrasion, reactivity, and other properties. Petrographic analysis is also made. Phase 3 is a physical and economic study of the site and involves determining quantity of stone avail- available, amount-and character of overburden, condition of haul roads and distance to rail shipping point, plant flow sheets and capacity, aggregate sizes produced, and approximate price of material at plant.

Jan 1, 1966

By D. J. Bauer

The Bureau of Mines demonstrated the feasibility of fractionating lanthanide nitrates with a tertiary amine on lanthanum-cerium and thulium-ytterbium pairs. Optimum values were determined for pH, phase concentration, and percent chelation of metal ions in the aqueous phase. Percent extraction is markedly dependent on the concentration of lithium nitrate in the aqueous phase. Selective masking of the heavier element in each extraction system with DTPA or EDTA aqueous-phase chelating agents resulted in lanthanum-cerium separation factors of 8.5 and thulium-ytterbium separation factors of 3.4.

Jan 1, 1966

By James S. Browning

The Bureau of Mines conducted laboratory and small--scale continuous tests of weathered mica pegmatite ores from Hart County, Ga., to determine the technical feasibility of recovering commercial-grade mica concentrates by flotation. Two modifications of the Bureau-developed anionic-cationic method were used. In one method, sodium carbonate and calcium lignin sulfonate were used for pH control and quartz depression; this method yielded mica concentrates containing 98.5 percent mica with a recovery of 91.4 percent. In the other modification, lime and sodium silicate were used with the calcium lignin sulfonate; concentrates containing 98.9 percent mica with a recovery of 86 percent were obtained.

Jan 1, 1966

By Jones S. C

The problem of sealing a fluid serieite zone at a hole depth of 4000 ft was overcome by using a composite non-return valve plug and rod assembly which enabled cement to be forced under pressure into the zoneà

Jan 1, 1966

By F. E. Walker

The Bureau of Mines determined total sulfur and sulfur forms for coal in 283 counties in 29 States and 2 fields of the State of Alaska. Specifically, organic, pyritic, and sulfate sulfur were measured of approximately 2,900 samples, and they include most of the coalbeds in the United States.

Jan 1, 1966

By H. J. Ramey

The wellbore acts as a storage tank during drawdown and build-up testing and causes the sand-face flow rate to approach the constant surface flow rate as a function of time. This effect is compounded if non-Darcy flow (turbulent flow) exists near a gas wellbore. Non-Darcy flow can be interpreted as a flow-rate dependent skin effect. A method for determining the non-Darcy flow constant using this concept and the usual skin effect equation is described. Field tests of this method have identified several cases where non-Darcy flow was severe enough that gas wells in a fractured region appeared to be moderately damaged. The combination of wellbore storage and non-Darcy flow can result in erroneous estimates of formation flow capacity for short-time gas well tests. Fortunately, the presence of the wellbore storage eflect permits a new analysis which can provide a reasonable estimate of formation flow capacity and the non-Darcy flow constant from a single short-time test. The basis of the Gladfelter, Tracy and Wilsey correction for wellbore storage in pressure build-up was investigated. Results led to extension of the method to drawdown testing. If non-Darcy flow is not important, the method can be used to correct short-time gas well drawdown or build-up data. A method for estimation of the duration of wellbore storage effects was developed. INTRODUCTION In 1953, van Everdingen and Hurst generalized results published in their previous paper3 concerning wellbore storage effects to include a "skin effect", or a region of altered permeability adjacent to the wellbore. Later, Gladfelter. Tracy and Wilsey4 presented a method for correcting observed oilwell pressure build-up data for wellbore storage in the presence of a skin effect. The method depended upon measuring the change in the fluid storage in the wellbore by measuring the rise in liquid level. To the author&apos;s knowledge, application of the Gladfelter, Tracy and Wilsey storage correction to gas-well build-up has not been discussed in the literature. It is, however, a rather obvious application. Gas storage in the wellbore is a conlpressibility effect and can be estimated easily from the measured wellbore pressure as a function of time. Several approaches to the wellbore storage problem have been suggested. As summarized by Matthews, it is possible to minimize annulus storage volume by using a packer, and to obtain a near sand-face shut-in by use of down-hole tubing plug devices. Matthews and Perrine have suggested criteiia for determining the time when storage effects become negligible. In 1962, Swift and Kiel&apos; presented a method for determination of the effect of non-Darcy flow (often called turbulent flow) upon gas-well behavior. This paper provided a theoretical basis for peculiar gas-well behavior described previously by Smith. Recently, Carter, Miller and Riley observed disagreement among flow capacity k,,h data determined from gas-well drawdown tests conducted at different flow rates for short periods of time (less than six hours flowing time). In the original preprint of their paper, Carter et al. proposed that the discrepancy in flow capacity was possibly a result of wellbore storage effects. Results of an analytical study of unloading of the wellbore and non-Darcy flow were recorded by carter.14 In the final text of their paper, Carter et al.!&apos; stated that they no longer believed wellbore storage was the reason for discrepancy in their kgh estimates. In view of the preceding, this study was performed to establish the importance of non-Darcy flow and well-bore storage for gas-well testing. In the course of the study. a reinspection of the previous work by van Everdingen&apos; and Hurst&apos; was made, and the basis for the Gladfelter, Tracy and Wilsey&apos; wellbore storage correction was investigated and extended to flow testing. WELLBORE STORAGE THEORY As has been shown by Aronofsky and Jenkins,11-12 Matthews," and others, flow of gas can often be approximated by an equivalent liquid flow system. The following developnlent will use liquid flow nomenclature to simplify the presentation. Application to gas-well cases will be illustrated later. First, we will use the van Everdingen-HursP treatment of wellbore storage in transient flow to establish (1) the duration of wellbore storage effects, and (2) a method to correct flow data for wellbore storage. DURATION OF WELLHORE STORAGE EFFECTS When an oil well is opened to flow. the bottom-hole pressure drops and causes a resulting drop in the liquid level in the annulus. If V. represents the annular volume in cu ft/ft of depth, and p represents the average density of the fluid in the wellbore, the volume of fluid at reservoir conditions produced from the annulus per unit bottom-hole pressure drop is approximately: res bbl-- (V, cu ft/ft) (144 sqin./sq ft) psi -(5.615 cu ft/bbl)(pIb/cuft) ........(I)

Jan 1, 1966

By Joseph A. DeCarlo

Coal is one of our basic sources of energy (heat, power, light) and an essential raw material for most metallurgical processing. More than two-thirds of the electricity currently produced by thermal powerplants in the United States is generated by coal, and it is expected that coal will continue to be the major fuel used for this application at least through the 1970&apos;s. Coke produced from bituminous coking coal is the principal fuel of iron blast furnaces, and unless ironmaking methods change greatly, coal will continue to maintain a dominant role in iron-ore processing and steel manufacturing for many years. Export markets are expected to increase also, adding to the overall increased demand for coal. Accompanying the increased total requirement, however, will be an ever-increasing demand for higher quality coals, specifically, coals of low sulfur content. Except for special-purpose coals such as those used for the production if coke and ceramics where impurities in the fuel contaminate the end product, the amount of sulfur in coal has been only a minor consideration in the selection of a particular coal for fuel. Major considerations, particularly for the coals used to generate electric power, have been availability and cost. An increased national concern for control of air pollution, however, particularly that resulting from the emission of sulfur oxides in stack gases to the atmosphere, has led to more rigid specifications on coal quality, and the sulfur content of coals will become increasingly more important in the future.

Jan 1, 1966

By J. D. Vincent

The Mission By-Products Plant at the Mission Concentrator of the American Smelting and Refining Company, some 20 miles south of Tucson, Arizona in the Twin Buttes mining area, has been in operation slightly over a year. The plant produces a molybdenite concentrate a copper concentrate and, at times, a zinc concentrate. An intensive test program of over three years was conducted at Mission to make the recovery of molybdenum economic. Briefly it was found necessary to make a scavenger concentrate in the copper mill before it was possible to recover economic quantities of molybdenite. By so doing there were resulting additional recoveries of copper, silver and zinc. This program resulted in the design and construction of the existing plant. A paper by the authors discussing the test work and the design was presented at the, October 1965 meeting of the American Mining Congress in Las Vegas, Nevada, by Mr. Wayne Bossard.

Jan 1, 1966

By Rogers F. Davis

The Bureau of Mines developed a new method for the determination of oxides of nitrogen in diesel exhaust gas. The procedure, a modification of the Saltzman method, uses a NO2 absorbent for the diesel exhaust gas; the colorless absorbent becomes purple on contact with N~. When used properly this procedure gives satisfactory results in 2 hours, whereas the standard phenoldisulfonic acid method required approximately 8 hours. The new method is not satisfactory for determination of oxides of nitrogen in the overrich fuel to air ratio range.

Jan 1, 1966

By Leo A. Schrider

This report analyzes the successful low-pressure gas drive in the Keener sand of the Bonds Creek oilfield, Pleasants and Ritchie Counties, W. Va.) and predicts its future performance. Core analysis from two wells and electrical and radioactivity logs were used to evaluate the reservoir characteristics. Production records over a 37-year period indicate that over 240,000 barrels of oil have been produced from the Keener sand by low-pressure gas injection. Decline-curve analysis shows that 165,000 additional barrels should be recovered from 108 acres of productive sand by continuing this secondary-recovery method.

Jan 1, 1966

By J. D. Allen

The Concord Mine Coal Preparation Plant of United States Steel Corporation, located near Bessemer, Alabama, began operations in June, 1950. The basic cleaning circuit consisted of a Chance Cone for cleaning the 2-inch x 3/8-inch fraction and concentrating tables for cleaning the minus 3/8-inch coal fraction. Dewatering of the final product was accomplished with 35-mesh vibrating screens. However, because Concord coal is very friable (Figure 1), 85 per cent passing three mesh and 25 per cent passing 28 mesh, there was a considerable amount of fines passing through the dewatering screens. To recover these fines, the dewatering screen effluent was sent to two 70-foot diameter hydro-separators with the underflow returning to the dewatering screens and the overflow going to a 175-foot diameter thickener for water clarification, (Figure 2). As might be expected, there was a considerable amount of recirculation of the minus 35-mesh coal in this system. This degraded the coal and led to higher moistures. It also resulted in a fines bleed-off of plant water and thickener underflow to a fine-coal settling pond. In 1961, vacuum filters were installed to supplement the screens and to recover the fine coal lost in the bleed-off. The above system resulted in a product moisture of about 20 per cent. Further reduction to approximately 11 per cent was accomplished by drainage from railroad cars during transit to the coke plant. Control of the moisture at unloading was poor because of variations in operating levels and railroad car availability, but since the Concord coal constituted a smaller percentage of the coal previously used at the coke plant, the high moisture and fluctuations did not seriously hamper coking operations.

Jan 1, 1966

By Charles M. Mason

The Bureau of Mines evaluated equipment and procedures for drop-weight testing of explosive liquids as prescribed by Test 4) a widely used method. It was demonstrated that partial ignitions, originally designated as negative results, should be designated positives; it was also shown that wear or erosion of the sample cups and the type of mount used for the apparatus had important effects on the results. Relative sensitivity as measured by Test 4 was found to vary slightly with temperature. The Bureau also designed a fixed 2-kg weight and associated electromagnetic release, which subsequently were incorporated as standard in a revision of Test 4. The original concept that the test involves only adiabatic compression was found to be an oversimplification; an alternate mechanism for the initiation process is proposed in which due consideration is given to the effects of cavitation and microjets.

Jan 1, 1966