Search Documents

By F J. Kelly

A chemical process, based on laboratory investigations, is proposed for the production of high-purity niobium oxide from a pyrochlore-perovsk1te flotation concentrate produced from ore obtained at the Oka, Quebec property of Columbium Mining Products Limited. The method developed included the decomposition and dissolution of the flotation concentrate with hot, concentrated sulphuric acid. The dissolved niobium was purified and concentrated by a solvent extraction step, using methyl isobutyl ketone as the extractant. The niobium was recovered from the extractant with ammonium fluoride solution from which niobium oxide was precipitated with ammonia. Finally, the filtered and washed precipitate was calcined. Ninety-six per cent of the niobium was recovered in a product analysing 99.9 per cent Nzo.. The reagent cost was in the range of $1.00 to $1.25 per pound of niobium recovered. Introduction OVER the past few years, Columbium Mining Products Limited has been engaged in the development of a niobium-bearing mineral deposit in the vicinity of Oka, Quebec. One phase of this program resulted in a flotation process capable of producing concentrates containing up to 50 per cent Nb205? Flotation pilot-plant

Jan 1, 1965

By John Nagy

Results of initial research by the Bureau of Mines are given on the dust explosion hazard of float coal and on the related factors of occurrence, rate of production, sampling techniques, transport, and deposition of float coal. Tentatively, it is suggested that where float coal deposits prevail, a mini-mum of 80 percent incombustible be maintained in the top 1/8-inch layer to neutralize the explosion hazard of the surficial coal deposit.

Jan 1, 1965

Jan 1, 1965

By G. Rowan, M. W. Clegg

Approximate analytical solutions for non-Darcy radial gas flow are derived for bounded and infinite reservoirs producing at either constant rate or constant pressure. These analytical solutions are compared with published results for non-Darcy flow obtained on digital and analogue computers, and the agreement is show to be very good. Some observations on the interpretation of gas well tests are made. INTRODUCTION The flow of gases in porous media is a problem that has been the subject of much study in recent years [l - 71 , and many methods have been proposed for solving the non-linear equations associated with it. The assumption that the flow satisfies Darcy's Law It has been observed, however, that the linear relationship between the flow rate and pressure gradient is only approximately valid even at low flow rates, and that as the flow rate increases the deviations from linearity also increase. It has been suggested by a number of authors that Darcy's Law should be replaced by a quadratic flow law of the form This form of equation was first suggested by Forchheimer [9] and, later, Katz and Cornell [10], and Irmay [lll, developed a similar equation. Houpeurt [12] derived this form of equation using the concept of an idealised pore system in which each channel consists of sequences of truncated cones giving rise to successive restrictive orifices along the channel. This type of representation leads to a quadratic flow law of type [4], for all fluids, but it is found that the quadratic term is only significant in the case of gas flow. The methods of Houpeurt for solving gas flow problems will be discussed further in another section of this paper. Solutions of the non-linear equation for Darcy gas flow 121 may be classified as either computer (digital and analogue), or approximate analytical ones. The former include the well-known solutions of Bruce et al. [13], and Aronofsky and Jenkins [14] , but the latter solutions, apart from the simple linearisation of equation (2) to yield a diffusion equation in p2 , are not so well-known. Amongst these approximate analytical solutions should be mentioned the work of Barenblatt [IS], who has applied the techniques of dimensional analysis to obtain similarity solution to a large class of non-linear equations; also, a number of Russian authors, including Barenblatt [16] , Kim [17] and others, who have used the method of moments for obtain-

Jan 1, 1965

By Wilbur I. Duvall

A linear array of shot and gage holes 30 feet deep in a granite outcrop was used to compare the size and shape of radial strain pulses produced in the rock when short cylindrical charges of cast composition B were detonated axially or at one end. The axially detonated charges produced radial strain pulses that had shorter rise times and larger peak strain than the strain pulses produced by end detonated charges.

Jan 1, 1965

By E. L. Dougherty, J. W. Sheldon

Using the numerical techniques shown in this paper it is possible to compute the simultaneous dynamical behavior of multiple fluid-fluid interfaces in two dimensions. Hence, fluid-fluid inter face models of several oil recovery processes can be constructed which allow prediction of the effect of fluid flow in two dimensions on the behavior of these processes while taking into account various physical effects, such as saturation gradients, phase changes and thermal stimulation. Techniques for constructing fluid-fluid interface approximations for several oil recovery processes are reuiewed. The validity of these techniques is established by comparison to experimental results. The availability of a computer program for computing the behavior of multiple fluid-fluid interface problems makes the use of potentiometric models uneconomic. The results indicate the areal sweep efficiencies obtained from potentiometric model studies at high mobility ratios may be somewhat optimistic. The results also indicate that the areal sweep efficiency curves obtained at high viscosity ratios 2—4 using miscible fluids in porous media are misleading and that considerable care must be taken in defining the mobility ratio for a displacement process, especially for miscible fluids. INTRODUCTION Many of the methods used to estimate areal sweep efficiency assume that the oil recovery process can be represented by one or more fluid-fluid interfaces. When the mobilities of the displaced and displacing phases are assumed equal, this quantity can be computed using analytical mathematical methods.l.2 For non-unit mobility ratio, experimental methods based upon the fluid-fluid interface concept include potentiometric and electrolytic blotter models. Scaled models of porous media have also been used to study this problem. Fay and Prats3 and Aronofsky4 used numerical techniques to compute breakthrough sweep efficiency, but neither of these studies were extended beyond breakthrough. Numerical techniques which have been developed for solving a general fluid-fluid interface problem are presented in a companion paper.5 These techniques have been incorporated into a program for a large-scale digital computer which can treat simultaneously the dynamical behavior of as many as six fluid-fluid interfaces. Thus it is possible to simulate the behavior of several oil recovery processes taking into account such effects as saturation gradients. Techniques for representing several oil recovery processes by fluid-fluid interfaces are presented. Processes considered are conventional water flooding with and without a mobile gas phase, hot water flooding, miscible flooding and enriched gas drive. Other processes, whose effects could be studied by this technique, but are not considered in detail here, are underground combustion and steam injection processes and various slug processes such as gas-water injection and alcohol-solvent processes. Theoretical results obtained with single interfaces for mobility ratios of 0.25, 1, 2, 4, 8, 16, 32 and 64 in a repeated five-spot are compared to experimental results for this geometrical configuration obtained using miscible fluids and conductive analogs. Predicted recovery curves for water flooding in a repeated five-spot are compared to experimental results reported in the literature. Example calculations are shown for a conventional water flood in the presence of a free gas phase and for a hot-water flood. MATHEMATICAL PRELIMINARIES We assume that the rock matrix is homogeneous with constant thickness, absolute permeability and porosity. The fluids are incompressible. We also neglect the effects of gravity.

Jan 1, 1965

By J. P. Neumann, L. Raymond

At temperatures near 1000°C, only the (112) (111) slip systems are operatire in tungsten. Therefore, the substructure introduced into the billet upon rleforming a single crystal by rolling at 1000 "C can be controlled by proper selection 01. processing ral'iubles. Using a reduction of 10 pct pel- pass, the (001)[110] and the (110)[001] crystals will deform by duplex slip rip to a 50 pet reduction in thickuess. These rolled single-crystal sheels are characlerized by anisotropic hardening, retention of ductility with warm working, lattice bending which is related to the conlacl (angle, and macroscopic dimensional changecs in the length bid not the width of the billet. When several slip systems become operative, a greater degree of work hardening is itztvoducetl into the crystal. This rolling- condition is characlerized by isotropic hardening, loss of ductilily with warm working, complex lattice distortions, and macro-scopic dimensional changes in both the length rind Width of the billel. IN tungsten, the {1 10}(111) slip systems are operative below room temperature,' while above 700°C only the {112{ (111) slip systems are observed.2,3 In the transition region, i.e., room temperature. both systems appear. It is the purpose of this investigation to show that tungsten single crystals deformed by rolling at a temperature where only one slip system is operative generate dislocation substructure which depends on the crystal orientation. For a specific crystal orientation. the resulting dislocation substructure can be further influenced by modifying the rolling procedure. Crystals oriented for multiple slip display less substructural sensi- tivity to modifications in processing techniques than do single crystals oriented for duplex slip. Under simple slip modes of deformation, very little work hardening is introduced into a rolled single-crystal sheet. Mechanical properties such as room-temperature strength. ductility, and hardness are used to confirm the existence of the different work-hardened conditions generated within the crystal by modified warm-rolling techniques. EXPERIMENTAL PROCEDURE Material. Single-crystal billets of four different crystal orientations. grown by the Arc-Verneuil technique. were ground to a size of 0.25 by 0.375 by 3 in. In terms of their rolling plane and rolling direction, the billets had the following orientations: (1101 [001 ] (110) [110] (001) [110] (001) [100] The actual orientation of all crystals was within 5 deg of the ideal orientations. The typical impurity content of the crystals is given in Table I. Polishing and Etching. Polishing was done elec-trolytically in a 20 g per liter aqueous solution of NaOH at approximately 10 v. It was established by the Laue back-reflection X-ray technique that the surface damage due to grinding and cutting operations with a diamond wheel did not exceed 0.001 in. Therefore after each cutting or grinding operation at least 0.002 in. was removed electrolytically from the surface in order to eliminate surface effects. By lowering the voltage to 3 v, subgrain boundaries and individual dislocations are identified in agreement with Berlec 4 where the etch-pit traces on a cubic plane form a square. The etching time was about 5 sec at room temperature. Rolling. Rolling was carried out on a Loma 2-high mill (Model 600). The peripheral velocity of the 6-in.-diameter rolls was 500 in. per min, with the surface temperature of the rolls about 400° to 450° C The billets were heated before each pass for 30 min in argon to 1000 C. Oxidation of the crystals during rolling in air resulted in a thin layer of greenish-yellow WO 3 This oxide was removed after each pass by immersing the crystals for a few minutes in a boiling NaOH solution. Prior to the initial rolling pass, a surface layer of 0.001 in. was removed by polishing. The crystals were then annealed in vacuum (10-4 torr) at 2400 C for 30 min. All crystals were rolled in the same direction; i.e., the same end was always introduced into the rolls. The rolling program was conducted in

Jan 1, 1965

By H. R. Thresh

An oscillational vis cometer has been constructed to measure the viscosity of liquid metals and alloys to 800°C. An enclosed cylindrical interface surrounds the molten sample avoiding the free surface condition found in many previous measurements. Standardization of the apparatus with mercury has verified the use of Roscoe's formula in the calculation of the viscosity. Operation of the apparatus at higher temperatures was also checked using molten lead. Extensive measurements on five different samples of zinc, of not less than 99.99 pct purity, indicate i) impurities at this level do not influence the viscosity and ii) the apparatus is capable of giving reproducible data. The variation of the viscosity ? with absolute temperature T is adequately expressed by Andrade's exponential relationship ?V1/3 = AeC/VT , where A and C are constants and V is the specific volume of the liquid. The values of A and C are given as 2.485 x 10-3 and 20.78, 2.444 x 10-3 and 88.79, and 2.169 x 10-3 and 239.8, respectively, for mercury, lead, and zinc. The error of measurement is assessed to be about 1 pct. Prefreezing phenomena in the vicinity of the freezing point of the zinc samples were found to be absent. AS part of an over-all program of research on various phases of melting and casting nonferrous alloys, a systematic study of some physical properties of liquid metals and their alloys was undertaken in the laboratories of the Physical Metallurgy Division.1,2,3 The most recent phase of this work, on zinc and some zinc-base alloys, was carried out in cooperation with the Canadian Zinc and Lead Research Committee and the International Lead-Zinc Research Organization. One of the properties investigated was viscosity and the present paper gives results on pure zinc; the second part, on the viscosity of some zinc alloys, will be reported separately. Experimental interest in the viscosity of liquid metals has virtually been confined to the past 40 years. The capillary technique was already established as the primary method for the viscosity of fluids in the vicinity of room temperature; all relevant experimental corrections were known and an absolute accuracy of 1 to 2 pct was possible. Ap- plication of the capillary method to liquid metals creates a number of exacting requirements to manipulate a smooth flow of highly reactive liquid through a fine-bore tube. Consequently, the degree of precision usually achieved in the high-temperature field rarely compares with measurements on aqueous fluids near room temperature. However, the full potential of the capillary method has yet to be explored using modern experimental techniques. As an alternative, many investigators in this field have preferred to select the oscillational method. Unfortunately, the practical advantages are somewhat offset by the inability of the hydrodynamic theory to realize a rational working formula for the calculation of the viscosity. In attempting to overcome this restriction many investigators have employed calibrational procedures, even to the extent of selecting an arbitrary formula for use with a given shaped interface. However, where calibration cannot be founded on well-established techniques, the contribution of such experiments to the general field of viscometry is questionable. A critical appraisal of the viscosity data existing for pure liquid metals reveals a somewhat discordant situation where considerable effort is still required to establish reproducible and reliable values for the low-melting point metals. The means of rectifying this situation have gradually evolved in recent years. Here, the theory of the oscillational method has undergone major advances for both the spherical and cylindrical interfaces. The basic concepts of verschaffelt4 governing the oscillation of a solid sphere in an infinite liquid have been adequately expressed by Andrade and his coworkers.5,6 Employing a hollow spherical container and a formula, which had been extensively verified by experiments on water, absolute measurements on the liquid alkali metals were obtained. The extension of this approach to the more common liquid metals has been demonstrated by culpin7 and Rothwel18 where much ingenuity was used to surmount the problem of loading the sample into the delicate sphere. Because of the elegant technique required to construct a hollow sphere, the cylindrical interface holds recognition as virtually the ideal shape. On the other hand, loss of symmetry in one plane increases the complexity of deriving a calculation of the viscosity. The contributions of Hopkins and Toye9 and Roscoe10 have markedly improved the potential use of the cylindrical interface in liquid-metal viscometry. The relatively simple experi-

Jan 1, 1965

By R. L. Stegman, M. R. Achter

R. L. Stegman and M. R. Achter (U.S. Naval Research Laboratory)—In a study of the surface structures developed in the fatigue of nickel at low strains as a function of temperature, we have obtained similar results.3 As our apparatus permits fatigue tests to be conducted in vacuo, there was no masking of the surface at high temperatures by oxidation so that the structures there could be observed directly. The relatively few broad slip bands observed at room temperature gave way at 300°C to a large number of uniformly distributed and narrower slip bands. At 550°C deformation began to concentrate around the grain boundaries and progressively increased up to 800°C. In addition fatigue strength was observed initially to increase with increasing temperature up to about 600°C due to the effectively increased ductility caused by the dispersal of fatigue damage. The fatigue strength then decreased at higher temperatures as grain boundary cracking dominates. Maria Ronay, W. H. Reimann, and W. A. Wood (authors' reply)— The authors are pleased to note that R. L. Stegman and M. R. Achter reach similar conclusions from their study of surface slip on nickel. However, they would emphasize that their own conclusions are based on what is shown by study of specimens that have been sectioned and that this study also shows that surface slip is not necessarily representative of what happens below the surface.

Jan 1, 1965

By R. E. Pray, M. C. Fuerstenau, J. D. Miller, B. F. Perinne

Quartz cannot be floated with potassium amyl xanthate as collector at any pH. Complete flotation is achieved with certain minimal additions of amyl xanthate and Pb from pH 5.8 to 8.5 and with amyl xanthate and Zn from pH 7.5 to 8.1. The active species of these metal ions responsible for activation are shown to be PbOH and ZnOH No flotation was effected when Cu and Mg were added as activators. Previous work1,2,3,4,5,6,7 has shown that quartz may be floated in the presence of sulfonate or soap when the following two criteria are met: 1) some portion of the added metal ion has hydro-lyzed to its first hydroxy complex, and 2) a precipitate of the metal-collector has formed. Since sulfonate and soap, two substantially different anionic collectors, conform to these criteria, this phenomenon may well be expected to be of a general nature. In this view then, it would appear that any anionic collector, including xanthates, should also float quartz when these two criteria are met. The object of this paper is to demonstrate the conditions under which quartz will respond to flotation in the presence of potassium amyl xanthate. EXPERIMENTAL MATERIALS AND TECHNIQUES Quartz was prepared by leaching the sized sample (48 x 150 mesh) with HC1 until no iron could be detected in the leach liquor. Conductivity water, made by passing distilled water through an ion exchange column, was used in the investigation. Potassium amyl xanthate was selected as collector. Purification of this reagent was effected with the following method: 1) a laboratory sample of potassium amyl xanthate was dissolved to saturation in hot ethyl alcohol and filtered several times while still hot, 2) the filtrate was cooled, during which time potassium amyl xanthate crystallized out of solution; the xanthate was then separated from the solution by filtration, 3) the amyl xanthate was dissolved in fresh hot ethyl alcohol and filtered, 4) step (2) was repeated, 5) the crystalline potassium amyl xanthate was washed with ethyl ether five times, and 6) the xanthate was dried for 24 hours under continuous vacuum. Inorganic impurities are insoluble in hot ethyl alcohol whereas dixanthogen is soluble in ethyl ether. Five-gram charges of 48x150 mesh quartz were conditioned for 3 min in 125 cc of solution containing the reagents and were floated with the small-scale cell and procedure described in previous papers.478 Reagent grade HCl and NaOH were used for pH adjustment, while reagent n-amyl alcohol was added as frother. Frother addition is necessary with this technique, but it should be mentioned that data, similar to those shown in Fig. 2 for 1 x10-4 mole per liter Pb++ and 1 X 10-4 mole per liter AX-, were also obtained with a Hallimond cell in the absence of frother. EXPERIMENTAL RESULTS Clean quartz could not be floated with amyl xanthate at any pH. Flotation was achieved under certain conditions, however, when various metal ions were added to the system. The activating ions used were lead, zinc, copper and magnesium, added as reagent grade chloride salts. Lead as Activator: The effect of Pb++ as activator was examined at five different additions of amyl xanthate (Fig. 1, 2 and 3). When 1x 10-5 mole per liter xanthate was added in the presence of 1 x 10"4 mole per liter Pb ++, no flotation was obtained at pH 6.5 or below, while a recovery of about 60% was effected at pH 7. When the pH was increased to 7.8, no flotation was again obtained, Complete depression was noted from pH 7.8 to about 10, at which point a recovery of about 30% was achieved. At about pH 11, the precipitate of lead amyl xanthate which was present below this pH dissolved and complete depression occurred. When 2.5x 10-5 mole per liter xanthate was added with the same lead addition, no flotation was obtained at pH 5.8 and below, whereas a recovery of

Jan 1, 1965

By W. F. Hosford

A series of aluminum single crystals was subjected to axially symmetric flow by drawing through dies. The orientation dependence of the drawing stress, which indicates the resistance to this type of flow, compares reasonably with predictions of Taylor and of Bishop and Hill. Measured lattice rotations likewise are generally consistent with theory. The most successful analyses of the plastic behavior of polycrystalline metal and its relationship to single crystal behavior are those of Taylor1-3 and of Bishop and Hill.4-6 The purpose of this paper is to provide a critical test of some of the basic assumptions involved in these theories. Both treatments apply to fcc metals and assume the shape change of each grain in a polycrystal to be the same as that of the polycrystal as a whole. Thus for a randomly oriented polycrystal extended under uni-axial tension each grain is assumed to undergo axially symmetric flow. dey = dez = -1/2dex, deyZ = dezx = dexy = 0 [l] where x, y, and z are a set of orthogonal axes, x being the tensile axis. Although [011.] oriented grains in bcc and fcc metals may depart markedly from this ideal behavior,7,8 the assumption is probably quite reasonable for most grains. Under a uniaxial tensile stress, ox, the work dW per unit volume expended in producing an increment of axial strain dex is, dW=oxdex [21 Since this work is expended in slip, dw =STi dyi 131 where Ti and yi are the shear stress and shear strain on the active slip systems. In both analyses Ti is taken to be the same on all slip systems, and dependent only on the total prior shear strain on all systems, so dw = Tdy [41 where t is the shear stress required for slip and y is the sum of the shear strain yi on all slip systems. Combining 121 and [4] and defining M = oX/T The ratio M is a generalized Schmid factor. It relates the tensile stress required for axially symmetric flow, ox, to the basic shear stress, 7, and it also expresses the ratio of crystallographic strain, y, to the tensile strain, Ex It depends only on the orientation of the crystal. Taylor evaluated M for various orientations by finding the least value of dy/dEx which could satisfy the shape change. Bishop and Hill, on the other hand, found M by considering the relative work (1/T)dW/dEx expended by stress states which could activate enough slip systems to produce the shape changes. The results of both methods appear to be equivalent, although certain omissions were made in Taylor's original work. The orientation dependence of M, calculated by the second method,9 is shown in Fig. 1. Taylor used the average 2= 3.06 for all possible orientations to predict the tensile stress-strain curve (oxvs Ex) for a random polycrystal from the shear stress-strain curve (t vs y) of a single crystal. Changes in M from lattice rotation were neglected so points on the ox vs ex curve were simply taken at ox = 3.06t and e = y/3.06 from corresponding points on the t vs y curve. Recent extension of the analyses of Taylor and of Bishop and Hill to crystallographically textured metals has been used to relate plastic anisotropy to textures, and to predict the potential texture hardening that could result from texture control.9 Unfortunately there have been relatively few experimental tests of the underlying theory. Taylor found that the tensile stress-strain curve of polycrystalline aluminum did agree reasonably well with that predicted from a single-crystal T-y curve. Had the single crystal undergone easy glide, how-

Jan 1, 1965

By B. A. Wilcox, A. H. Clauer

DURING the course of an investigation on the high-temperature creep behavior of TD Nickel* (Ni + 2) vol pct ThO2), it was observed that the creep fractures were similar in appearance to low-temperature ductile fibrous fractures and creep ruptures by cavitation. Microfractographs of fibrous ruptures are typically characterized by a dimpled appearance, with second-phase particles frequently found near the bottom of the dimples.'-4 These somewhat resemble creep ruptures by cavitation, in that fracture occurs by void formation, with the subsequent growth and final merging of the voids to form a complete fracture.' It is the purpose of this communication to describe the creep fracture of TD nickel and suggest a mechanism for the rupturing process. The discussion is relevant to material crept to fracture in vacuo at a constant stress of 18,000 psi, over the temperature range 900" to ll00°C. The material used in this investigation was 1/2-in.-diam bar stock supplied by Du Pont, contain- ing 2.3 vol pct Tho2. The final fabrication treatment consisted of -95 pct reduction by swaging followed by a 1-hr anneal at 1000°C. Transmission and replica electron microscopy revealed that the material had a fibered structure with a transverse grain size of -1 µ and a longitudinal grain size of 10 to 15 µ. Selected-area diffraction indicated that the fiber axis was parallel to (00l), in agreement with the results of Inman et a1.6 The thoria particle size varied from 80 to 1000Å, with an average size of 400Å, and the mean particle spacing was about 1200Å. The remarkable structural stability7 was confirmed by annealing for 6 hr at 1300°C (about ' 0.9 the absolute melting point). Transmission electron microscopy revealed that the only structural change was a slight decrease in dislocation density. Furthermore, recrystallization or grain growth during creep has not been observed. All specimens were annealed in vacuo at 1300°C for 3 hr prior to creep testing. The following times to rupture were obtained for vacuum creep tests at a constant stress of 18,000 psi: 900°C, 854 hr; 930°C,

Jan 1, 1965

By Matthew Blecha

The Tribag copper deposit is one of the rare examples of mineralized breccias in the Canadian Shield. The breccia is a pipe-like body, and consists of granitic, diabasic and volcanic fragments embedded in a vuggy, quartz-carbonate matrix. The mineralization is essentially chalcopyrite and pyrite, with minor molybdenite, sphalerite, galena and other sulphides. The main ore zone is saddle-like in shape, and is enveloped in a zone of chloritization, sericitization and clay-mineral alteration. It is suggested that the breccia is of the diatreme type. Introduction T HIS paper is based on eighteen months of field work, including surface and underground geological mapping and core logging, and on the survey of relevant literature. No significant amount of laboratory work has been done as yet. Location and Access The Tribag Batchawana property is located 40 miles north of Sault Ste. Marie, Ontario, about 10 miles east of Lake Superior. A 17-mile, all-weather road connects the property to the Trans-Canada highway to the south, and 4 miles of a 12-mile road remain to be completed to link it to the Algoma Central Railway to the northeast.

Jan 1, 1965

By R. W. Lai, I. Iwasaki

Some physical as well as chemical aspects of the methods of dispersion of various corn starches and their derivatives are investigated and their effects as depressants in anionic silica flotation of iron ores ascertained. The adsorption behavior of starches on hematite and quartz is strongly affected by their molecular sizes as inferred from viscosity measurements. The implication of this behavior on flotation and flocculation is discussed. Mechanical treatment of causticized starch solutions is shown to reduce the starch requirements in flotation appreciably. Starches and starch products have been used as depressants for iron oxides both in amine flotation of siliceous gangue and in soap flotation of activated silica from iron ores. Cooke and his associates1,2,3,4 extensively studied the effects of certain starches and their derivatives in the amine flotation of iron ores at near-neutral pH and found that although most starches were good flocculants for hematite and de- pressed that mineral more or less selectively1,3 they did not flocculate quartz suspensions. Further, that replacement of active groups in corn starch modified its behavior as a flocculant for hematite or quartz suspensions1 and as an iron oxide depressant. Schulz and cooke2 showed that many starches and their derivatives, except aminoethyl starch, were abstracted more effectively by Brazilian hematite than by quartz and that the adsorption of a starch product was strongly dependent on pH and on the presence of calcium ion. In soap flotation of calcium-activated quartz, certain starches and their products have been used to depress iron oxides.5'6 The behavior of these substances in flotation appears at times to be at variance with those previously reported and especially with results obtained in the Mines Experiment Station laboratories. This is attributed, at least in part, to differences in flotation procedure and flowsheets and in the method of preparing the depressant. Most of the investigators referred to above, solubilized the starch products by autoclaving at 120°C. Others have used acid,7 alkali8 or oxidizing agents.9 In view of the limited knowledge of the depressing action of starches and their derivatives in iron ore flotation, particularly in soap flotation of calcium-activated silica at high alkalinity, an extensive study

Jan 1, 1965

By A. C. Losekamp, R. M. Fincel, J. B. Conway

TANTALUM like several other metals exhibits a great affinity for or reactivity with certain gases. Tested in atmospheres which are not completely pure this metal becomes contaminated by certain impurities (notably nitrogen, oxygen, and hydrogen) with a resultant change in various properties. Well-known are the drastic changes in hardness, ductility, and electrical resistivity. Also previously recorded are the distortions of the lattice1,2 accompanying the increased content of oxygen and nitrogen in tantalum. This pronounced affinity for certain gases along with the significant property variations thereby produced makes it necessary to observe additional experimental precautions in making various property determinations with tantalum. Some recent measurements of the linear thermal-expansion characteristics of tantalum have made this point quite emphatically. Failure to observe the greatest precautions in reducing the contaminating influence has led to some extremely distorted results. Not only does such operation lead to different heating and cooling curves during the thermal-expansion measurements, but upon cooling to room temperature the sample is found to have suffered a permanent (actually semipermanent since the specimen can be returned to its original length by a 3-hr degassing treatment in vacuum at 2300°C) elongation. In addition, subsequent heatings will not follow the initial heating curve unless the expansion measurements are based on the actual specimen length at the beginning of the heating cycle. These thermal-expansion measurements were made by positioning the specimen horizontally at the longitudinal midpoint of a 20-in.-long, 4-in.-diam resistively heated tungsten tube furnace. The specimens were in the form of 20-mil sheet formed into a sharp U-shape about 0.3 in. in width and 0.3 in. in depth. Fiducial marks in the form of 0.010-in. holes drilled at either end of the 2.5-in.-long sheet specimens were viewed by a paired filar micrometer telescope system mounted on an Invar bar on the top of the furnace. Tests were made in helium with temperatures measured by a Pt/Pt-lORh thermocouple to 1000°C; above 1000°C temperature was measured by means of an optical pyrometer sighted into a black-body hole drilled into the specimen-holding fixture in the vicinity of the specimen. Previous tests with black-body holes drilled in a 0.25-in.-diam rod specimen had confirmed the temperature uniformity between specimens and specimen-holding fixture in this furnace. A typical thermal-expansion curve for arc-cast tantalum in helium is shown in Fig. 1 for the case where no attempt is made to remove all the impurities from the cover-gas atmosphere. The initial heating curve appears smooth and has a shape characteristic of all metals. However, it is known that the sample begins absorbing impurities at temperatures above 1000°C which are sufficient to distort the lattice and lead to specimen lengths which are somewhat larger than would be obtained in the absence of contamination. During the cooling cycle the expansion curve is seen to be significantly different from the heating curve. This is due to the impurity content causing a semipermanent (i.e., permanent until the impurities are removed by vacuum degassing) deformation which will not allow the speci-

Jan 1, 1965

By T. R. Ingraham

The thermal decomposition of cupric sulfate and of cupric oxysulfate has been examined by deter-mining the equilibrium gas pressure generated over each pure compound. The equilibrium data have been used to calculate the thermodynamic properties of both compounds, and the results have been combined with previously published data to establish a predominance-volume diagram for the Cu-S-O system over the normal range of roasting temperature and gas composition used in the treatment of copper minerals. Copper oxysulfate recrystal-lizes at 1100°K with an apparently irreversible en-dothermic heat requirement of 2.9 * 0.3 kcal per mole. WHEN mixed sulfide minerals containing copper are roasted, either of two procedures may be followed, depending on the nature of the other metals. In the first procedure, the roasting is controlled to produce a maximum amount of water-soluble copper sulfate which may be removed selectively from the water-insoluble compounds of the other metals. In the second, control is directed toward the production of water-soluble sulfates of the other metals and an insoluble salt of copper. Effective control of either of these processes would be enhanced by knowledge of the thermal stability of cupric sulfate and of cupric oxysulfate. In this paper, established data for the thermal stability of cuprous and cupric sulfide and of cuprous and cupric oxide will be combined with new data for the therma1 stability of cupric sulfate and cupric oxysulfate, to designate the volumes of stability of the significant compounds in the Cu-S-O system in the temperature range 750° to 950°K. EXPERIMENTAL Materials, Apparatus, and Procedure. The copper source material used in all experiments was Fisher Certified Reagent Grade "anhydrous" cupric sulfate, for which the following analysis was supplied by the manufacturer: chloride, 0.002 pct; alkalies and earths, 0.2 pct; insoluble, 0.002 pct; iron, 0.020 pct. Cupric oxysulfate was prepared from the normal sulfate by two procedures. In the first, equimolar quantities of cupric oxide (prepared by decomposition of the sulfate) and cupric sulfate were ground together and heated under vacuum in a sealed silica vessel at 800°C. This procedure was subject to failure because of explosion of the silica vessels due to the pressure of the final traces of water released from the sulfate on the initiation of its decomposition. The second procedure involved roasting the cupric sulfate, with frequent rabbling, in a muffle furnace at 725°C for a period of 48 hr. This produced an excellent product, which was confirmed as copper oxysulfate by X-ray and chemical analyses. The experimental technique used was that of measuring the total pressure exerted by the sulfur trioxide, sulfur dioxide, and oxygen produced by the following reactions: 2 CuS04 = cuo • CuSO4 + SO3 [1] cuo . CuSO4 = 2 cuo + SO3 [2] SO3= SO2 + 1/2 O2 [3] The apparatus used in the experiments has been described previously.1-3 Its main feature of a U-tube mercury manometer in which the mercury is protected from corrosion by enclosure in a flexible Pyrex bellows. Before beginning a run, the interior of the apparatus, including the bellows-manometer and all connecting tubing, was thoroughly washed with hydrochloric acid and distilled water to remove any

Jan 1, 1965

By A. Gene Collins

This report discusses some of the chemistry and geochemistry of cesium and rubidium. Knowledge of the cesium and rubidium content of oilfield waters aids in resolving the origin of waters and petroleum, exploring for petroleum and other valuable minerals, discovering water pollution sources, and augmenting the knowledge of geologic formations. The methods described in this report permit the detection of less than 0.01 mg/l of cesium and/or rubidium in a complex oilfield brine or water. Solvents possessing high-dielectric constants were evaluated for their ability to extract cesium and rubidium tetraphenylboron from oilfield waters and for their flame emission characteristics. Nitroethane was selected and used for the extraction and flame spectrophotometric determinations because it gave the highest sensitivity. Cesium 137 and rubidium 86 were used to determine the extraction efficiencies, which were about 87 percent and 58 percent respectively using a single 10 ml nitroethane extraction from a distilled water matrix. The standard deviation of the determination was 0.0008 mg for cesium and 0.0007 mg for rubidium in the 0.01 mg range.

Jan 1, 1965

By J. J. Hauser, H. C. Theuerer

A cathode sputtering technique is described which elin7inates the need for ultrahigh vacuum in preparing thin films of materials sensitive to gaseous impurities. This technique uses a fraction of the atoms sputtering within an anode container to getter actice gases, such as HzO, Oz, and Nz. The gases alzd gettering metal are deposited on the container walls, thus shielding the coating zone of the system from contamination. The use of the method for preparing superconducting-normal metal couples such as Ph-Cu and Ph-Pt is described, and the properties of the individual and composite films are given and discussed. GETTER sputtering is a method which greatly simplifies the preparation of thin films in cases where composition control is critical. A major difficulty with conventional sputtering and other vacuum-deposition techniques is the contamination of the forming film caused by residual gases, such as H20, CO, Oz, and Nz, in the coating equipment. The difficulty arises from the fact that even when the residual pressure in the system is as low as 1 x 10"6 Torr, with a deposition rate of 10A per sec, there are as many contaminating gas collisions with the substrate as there are with film-forming metallic atoms. It is not surprising, therefore, that with reactive metals, such as tantalum and niobium or with semiconductors, such as silicon and germanium, films with properties far different from the starting materials are obtained. In the case of niobium and tantalum, deposited either by sputtering or vacuum evaporation in systems with reactive gases at pressures of the order of 1 x l0-' Torr, the loss of superconductivity is traceable to interstial oxygen or nitrogen. On the other hand, working in vacuum of the order of 1 x l0-" Torr, Marchand and enema' have shown that superconducting films of tantalum with properties approaching those of bulk material are possible. At this level of gaseous impurities -lo6 metallic atoms arrive at the substrate before a contaminating collision occurs again assuming a deposition rate of 10A per sec. It is evident from the above that any successful vacuum technique requires the elimination of reactive gases from the region of the system where coating is occurring. Getter sputtering accomplishes this using conventional vacuum equipment with residual pressures in the 106 Torr range. In fact? vacuum systems with residual pressures of lo-" Torr are adequate for most purposes. With this method, sputtering is confined within an anode can and, by geometric design, sputtering itself is used to purify the argon at the lower and upper parts of the system by the gettering action of the reactive metal. In consequence, the central region of the system where coating occurs is shielded from gaseous contamination. Getter sputtering is particularly useful for the preparation of alloy and compound films. With this method, if a cathode of homogeneous composition is bombarded with high-energy argon ions, transfer of material to the substrate having the same composition as the cathode will occur. This is true after an initial equilibration time, even though the constituents of the cathode may have different sputtering rates. During equilibration, the surface of the cathode changes composition due to differences in sputtering rate, but mass conservation demands a steady-state condition such that the atoms sputtered from the surface have the same composition as the cathode material from which the surface is generated. GETTER-SPUTTERING APPARATUS The original form2 of the getter-sputtering apparatus is shown in Fig. 1. It consists of a closed nickel or stainless-steel can 4 in. tall and 2-3/8 in. in diameter. Mounted symmetrically from each end

Jan 1, 1965

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By W. S. Landers

This report presents a detailed study of low temperature, entrained-bed carbonization of an Australian coking coal. The coal studied was high-volatile B bituminous from the Foybrook mine, an open-cut operation in the Liddell seam, New South Wales, Australia. Carbonization was conducted in an 8-inch diameter, continuous vertical reactor at several temperatures from 960° to 1,300° F. It was demonstrated that this bituminous coal can be carbonized within this temperature range to produce tar and a nonagglomerated char, without prior oxidation or char recirculation. Carbonization rates from 138 to 287 lb/hr (as-carbonized basis) were investigated. It was found that the carbonization temperature and the air-to-coal ratio must exceed minimum values to insure continuous operation. At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coa1 ratios, part of the heat for carbonization was supplied externally. On the moisture-and ash-free basis, the yield of tar plus light oil ranged from about 26 to 44 gallons per ton, and the char yield ranged from approximately 1,160 to 1,370 pounds per ton. The heat in the gas ranged from about 900 to 3,000 Btu/lb of moisture-and ash-free coal. Carbonization product yields correlated well with air-to-coal ratio and carbonization temperatures. The volatile matter in the char was found to be temperature dependent. At 1,300° F carbonization, the volatile matter in the char was 8.7 percent (dry basis), whereas at 9600 F carbonization, the residual volatile matter was about 16 to 18 percent (dry basis).

Jan 1, 1965