Search Documents

By F. W. Osterwald, C. R. Dunrud

A continuously recording seismic network was constructed in 1962 by the U.S. Geological Survey to locate epicenters and record incidence of bumps (bounces, rock bursts) that occur in the bituminous coal mines of the Book Cliffs coal field near Sunny-side, Utah. The coal is mined because of its value as coking coal, although these bumps may be a hazard to life and property. Daily records of tremors caused by bumps for 1 3/4 years indicate that a seasonal pattern, as well as a daily pattern, exists for the number of bumps that occur in a given period. Maxima occur in May and June and November and December. Marked increases at 5-day to 9-day intervals are superimposed on these seasonal maxima. The largest bumps commonly occur during seasonal maxima when the rate of occurrence suddenly decreases and the amplitude of the individual bumps increases. Knowledge of this pattern may lead to prediction of general locations and periods of increased hazard from bumps. Experience to date has shown that prediction of precise times and locations of hazardous bumps is not possible, and may never be; primarily because even a small bump can be a hazard to life and property. Some bumps or bump sequences are actually composites, consisting or two or more discrete bumps a few tenths of a second to a few seconds apart. Violent and spontaneous releases of coal and rock from faces, ribs and roofs of mines (termed bumps or bounces by miners) are a common hazard to life and property in the coal mines located in the Book Cliffs near Sunnyside, Utah (Fig. 1). These bumps

Jan 1, 1965

By K. C. Dean

This report is the first of a series concerned with processes for producing magnesium. These reports will evaluate metallothermic, carbothermic , and electrolytic production methods, and will furnish a cost basis for comparing the processes. Areas deemed most promising for future research will be delineated for each procedure. This report presents briefly the history of the metallothermic process, and describes the operations of the Defense Plant Corp. (DPC) plants that employed the process. A hypothetical plant designed to produce 12,000 tons of magnesium per year, using ferrosilicon as a reductant, is described, and raw materials, energy, and major equipment requirements are estimated. Several process modifications are suggested for future research.

Jan 1, 1965

By B. Ramaswami, U. F. Kocks, B. Chalmers

The latent hardening of silver and an Ag-Au alloy was investigated by lateral compression, overshoot in tension and cormpression, and the stability of multiple-slib orientations. The latent hardening of a secondary slip systenz depends on its relation to the primary slip system. For most secondary slip systems the latent hardening is larger for Ag-10 at. pct Au than for pure silver. The maximum increase in. flow stress on a secondary slip system over that of the primary slip system was 40 pct. The work hardening during the lateral-compression test on the latent system after prestress on the primary system is iuterbreted in terms of the preferential distribution of barriers to dislocation movement with respect to the active slip system in work-lzardened fcc crystals. The work-hardening in fcc crystals is mainly due to the dislocation interactions and the barriers to dislocation movement formed as a result of reactions between dislocations of different slip systems. The operation of sources on the latent system depends on the flow stress of those systems; hence, the increase in flow stress of a latent system due to glide on an active system, which is called latent hardening, is an important element in understanding the phenomenon of work hardening. The problem of latent hardening has attracted the attention of many investigators in the past. For example, a theoretical study of the elastic latent hardening of the latent systems due to glide on an operative system has been made by Haasen' and ~troh. These calculations, however, neglect the stress required for the intersection of forest dislocations by the glide dislocations, a factor which would be important for producing macroscopic strains on the secondary slip systems. The importance of this factor will become evident from the results presented here. Attempts have also been made to determine the latent hardening of different slip systems by experimental means by the methods summarized in Table I.3-9 The experimental methods used have been subject to certain limitations. For instance, in the method used by Hauser,9 frictional constraints between the specimen and the compression platen were not eliminated by proper lubrication (see Hos- ford10). Secondly, with the exception of Kocks,6 Hauser,9 and Rohm and Kochendorfer,11 latent-hardening studies have been made on only one of the slip systems, i.e., on either the conjugate or the coplanar slip system; hence, extensive results are not available on the latent hardening of different slip systems in the same materials, with the exception of aluminum.6 It was therefore decided to study the latent hardening of the conjugate, critical and half-related slip systems in silver. Similar experiments were done in Ag-10 at. pct Au to study the effect of solute (gold) on the latent hardening of silver. Lastly, indirect evidence can be obtained by a study of the orientation stability of crystals of multiple-slip orientations in tension and compression. This method has been used by Kocks6 to supplement his studies of latent hardening in aluminum. Similar studies were made at room temperature in single crystals of silver. EXPERIMENTAL PROCEDURE The single crystals of the desired orientations were grown and the tensile test specimens were prepared as described in Ref. 12. The compression tests were made on 1/4-in.-cube specimens. The specimens were cut from single crystals, in the Servomet spark-erosion machine.13 The two cut surfaces were planed using the lowest available planing rate in the machine to minimize the deformation layer. A brass strip was used as the planing tool. This method of preparation ensured plane parallel faces for the compression tests. The deformed material was removed by prolonged etching in a weak etching solution. A weak etching solution was used to prevent pitting of the surfaces and to ensure uniform etching. About 25 to 50 µ of material were removed from all faces by the etching treatment. The specimens were then annealed for 24 hr at 940°C in oxygen-free helium and cooled in the furnace to room temperature over a period of 7 hr. After annealing, the orientation of the specimens was determined by Laue back-reflection technique to make sure that no recrystallization had occurred on annealing. The compression-test technique and setup are described in Ref. 14. The Laue back-reflection technique was used to study the overshoot in tension, the overshoot in compression, and the stability of the axial orientation in tension and compression. The tests were interrupted after every few percent strain to determine the axial orientation. In investigating the overshoot in compression, the operative system was determined by studying the asterism of the Laue spots.

Jan 1, 1965

By R. W. Hertzberg, F. D. Lemkey, J. A. Ford

The technique of unidirectional solidification has been applied to the A1-AI3Ni and A1-CuAl2 ezltectic alloy systems; the controlled microstructure of A1-A3Ni consists of parallel A13Ni whiskers emhedded in an aluminum matrix while the Al-CuAl2, system solidifies as parallel alternate lamellae of aluminm and CuAl2. Mechanical tests (tension and flexure) have shown that the particle-matrix interface bond formed during unidirectional solidification allowes for efficient load transfer from the matrix to the reinforcing phase. Strength and fracture characterstics of the alloys were studied as a function of phase orientation; the tensile strength of controlled Al-Al3Ni samples was 43,000 psi (three times greater than that of as-cast specime~s). The strength of the Al-CIA2, cutectic was studied as a function of lamellae-flexure stress-axis orientation using a microbend apparatus. A twofold increase in outer fiber stress was observed as the lamellae were rotated from a position of no reinforcing (perpendicular to the stress axis) to one of maximum reinforcing (parallel to the stress axis), The brittle reinforcing constituent in each alloy (A13Ni and CuAl2) was observed to he the nucleating phase for fracture. It is to be concluded from this investigation that unidirectionally solidified eutectic alloys have a potential use as reinforcing coniposite) materials. In a recent review article, Chadwick1 has described the work of many investigators in the area of controlled solidification of binary eutectic alloys. Thus far, more than twenty eutectic alloys have been unidirectionally solidified to produce structures consisting of two phases in the form of alternating lamellae or as whiskers embedded within a continuous matrix; in either case, the phases are aligned parallel to the growth direction. In particular, Kraft and Albright2 have shown that the Al-CuA1, eutectic alloy exhibits a lamellar microstruc- ture as a result of unidirectional solidification while Lemkey, Hertzberg, and Ford3 have studied the A13Ni whisker-aluminum matrix morphology in the A1-A13Ni system. Whether these alloys could exhibit reinforcing behavior would have to depend upon the strength and volume fraction of the reinforcing phase (AI3Ni and CuA12) and the nature of the bond between the reinforcing phase and the matrix. Hertzberg and Kraft4 have shown that the interface bond between chromium whiskers and a copper matrix in unidirectionally solidified Cu-Cr is particularly good while Lemkey and Kraft5 have reported chromium-whisker tensile strengths in excess of 1,000,000 psi. However, with the chromium volume fraction being less than 2 pct, no reinforcing behavior was displayed by the Cu-Cr alloy.6 In view of the encouraging results concerning the good interfacial bond and high strength of the reinforcing phase in the Cu-Cr system and preliminary mechanical test data reported by Lemkey et al.3 for the A1-A13Ni system, the A1-CuA1, and A1-A13Ni eutectic alloys containing 50 and 10 vol pct, respectively, of the reinforcing phase give promise of possessing mechanical reinforcing behavior. Based on this premise, the objective of the investigation was to study the strength and fracture behavior exhibited by these anisotropic microstructures. EXPERIMENTAL PROCEDURE Controlled Solidification Procedure. An extensive description of the technique of unidirectional solidification has been presented elsewhere.' However, the pertinent details for each eutectic system studied are discussed below. Al-A13Ni System. Several master heats of this alloy were prepared by vacuum-induction melting in an A12O3crucible and casting in SiO2 mold or by induction melting in alumina crucibles under argon. The initial heats were prepared from 99.99 pct A1 and 99.99+ pct Ni, while later heats used 99.999+ pct A1 and 99.99+ pct Ni. Specimens of these master heats were unidirectionally solidified using induction and resistance heating sources and argon atmospheres at growth rates from 1.1 to 28.7 cm per hr. The thermal gradients in the liquid were controlled in the range of 26" to 36°C per cm for these runs. Al-CuA12 System. The master heat and controlled

Jan 1, 1965

By D. S. Tomalin, D. F. Stein

The effect of reducing oxygen to low concentrations on the fracture of high-purity iron single crystals has been examined at 78° and 20°K. It is found that iron single crystals grown by the strain-anneal method usually contain a few occluded grain boundaries which may become embittled in the presence of oxygen, thereby nucleating cleavage fractures. High purity with respect to interstitial elements was found to inhibit twinning and evidence is presented for an orientation dependence of the resolved yield stress. Deformation occurred by slip rather than twinning at both temperatures of testing with elongations of as much as 9 pct at 20°K. THE fracture properties of iron single crystals have been observedl-3 to be a function of temperature, orientation, and purity. Allen, Hopkins, and McLennan1 demonstrated that at 78°K iron single crystals became increasingly brittle as the tensile axis approached the (001) pole of the stereographic unit triangle. Iron crystals with the tension axis near a (001) pole were completely brittle and orientations near the (011)-(111) boundary were very ductile, achieving a 100 pct reduction in area prior to fracture. Later work of Biggs and pratt2 and of Edmondson3 demonstrated that by reducing the carbon content of the single crystals the transition between brittle and ductile failure at 78°K could be shifted to orientations nearer the (001) pole. Ed-mondson went further and pointed out that any mechanism which tended to increase the yield strength of the iron (i.e., carbon addition, pre-strain) also increased the tendency for brittle behavior at 78°K. Thus by a reduction of carbon content Biggs and Pratt were able to obtain ductile behavior to within 20 deg of the (001) pole, and Ed-mondson was able to obtain ductile behavior to within 26 deg of the (001) pole. Edmondson's material had a total interstitial content (carbon, oxygen, and nitrogen) of approximately 60 ppm and, although Biggs and Pratt reported no analysis, indications were that their iron contained comparable impurities. Stein, Low, and seybolt4 purified iron single crystals to a total carbon, oxygen, and nitrogen content of approximately 20 ppm. They observed a lowering of the yield stress with this increased purity, and thus one might have expected an observation of increased ductility. Although they tested specimens of orientations which the previous workers had indicated should be ductile, the crystals failed at a 78°K in a brittle manner with little elongation. Stein noted,' however, that about 90 pet of the failures could be traced in origin to occluded grains. Allen et al.1 and Edmondson3 do not report examination of their cleavage surfaces, but Biggs and pratt2 reported that microscopic examination of the cleavage surfaces of many of their specimens revealed the presence of small occluded grains. Honda and cohen6 and Keh7 have also observed the initiation of fracture at occluded grains in iron single crystals. Therefore, the additional complication of occluded grains must be considered in studying the properties of iron single crystals and the origin of fractures determined if the ductility exhibited by the crystals is to be considered meaningful. Various investigators8-12 have studied the effects of impurities on grain boundaries in high-purity polycrystalline iron. Rees and Hopkins10 showed that the addition of oxygen to low-carbon (0.002 pet) iron weakened the grain boundaries, causing a shift from transcrystalline to intercrystalline fracture and a progressive decrease on the brittle-fracture stress with increasing oxygen content. In addition, it has been shown by Low and Feustel11 that the addition of carbon to polycrystalline iron containing oxygen eliminated grain boundary brittleness. Thus, oxygen can embrittle grain boundaries in high-purity polycrystalline iron, but the addition of an appropriate amount of carbon can eliminate the oxygen-induced brittleness. The oxygen content (19 ppm) of the iron "single crystals" employed by Stein el al. was large enough to suspect impurity effects at the occluded grain boundaries. Allen et al.1 Biggs and pratt,2 and Edmondson3 may have masked any occluded grain problem in their specimens considering the relatively high carbon levels they employed. stein13 demonstrated that the addition of as little as 0.9 ppm C to previously purified (less than 5 x 10-3 ppm C) "single crystals" would increase the elongation from a few percent to more than 20 pet at 78°K and the fracture was not associated with grade boundary initiation.

Jan 1, 1965

By A. T. Harris

Ground quartzite, known in the industry as amorphous silica, is produced from a quartzite deposit near Honey Brook, Pa., by George F. Pettinos, Inc., of Bala-Cynwyd, Pa. The quartzite is mined by the open pit method and processed in a mill at the mine. The operation regularly produces five standard grades of sand and one grade of crushed stone; however, the company accepts special orders and will produce material to meet the customer's specifications. Beneficiation (chiefly crushing and screening) is controlled by laboratory screen tests on samples taken during preparation of the sand. The chief uses of the sand are for foundry operations, furnace lining, concrete aggregate, and Other specialized uses. The quartzite in this deposit is of uniform composition and does not require control by chemical analysis. However, for special purposes, analysis will be furnished.

Jan 1, 1965

By P. M. Kelly

TWO analytical methods for calculating the positions of matrix and twin reflections on electron-diffraction patterns of a twinned cubic crystal have recently been published.1,2 Meieran and Richman1 considered the case of twinning on (1 12) in a bcc structure, while a more general treatment, capable of analyzing twinning on any plane in a cubic crystal, was developed by Johari and Thomas.2 The latter authors applied their general rotation matrix to both (111) twinning in face-centered crystals and {112} twinning in body-centered crystals and they derived separate expressions for these two cases. This separate treatment masks the fact that in a holosymmetric cubic crystal a (111) twin is crys-tallographically equivalent to a {112} twin.3 This is analogous to the crystallographic equivalence of rotation and reflection twins in centrosymmetric crys tals. A particularly simple example of this equivalence occurs when the two twin planes are perpendicular to each other—for example (111) and (112). Then, if twinning on (111) moves a point P to a new position P1, and twinning on (112) moves P to P2, P1 and P2 will be related to each other by a 180-deg rotation about [110]— the direction normal to both (111) and (112). Since there are diad axis axis along (110) direction in a holosymmetric cubic crys tal the two positions P1 and P2 must be crystallo-graphically equivalent. In other words if a particular pole (hk l) is in a position P1 after twinning on (Ill), then after twinning on (112) a pole of the type {hkl}—but not the particular pole (hk1)—will also be in the position P1. As a result, when only the general (as opposed to the particular) indices of poles after twinning are required, twinning on (111) gives the same results as twinning on (112). To convert the results for a (111) twin to those applicable to a (112) twin, when the particular (as opposed to the general) indices of poles after twinning are required, all that is necessary is to multiply the indices of the twin poles by the matrix for 180-deg rotation about [lie], i.e., The analytical methods suffer the disadvantage that a new set of calculations must be performed for each different diffraction pattern or, as is done in the Meieran and Richman treatment,1 a lengthy list of the location of the twin spots in reciprocal space must be prepared. All the tedious computation involved in these analytical approaches can be avoided by simply plotting, on tracing paper, a stereographic projection of a crystal twinned on say (112). By superimposing this twin stereogram on a standard (001) projection (preferably with the points and indices in a different color from those on the twin stereogram) the relative positions of both matrix and twin reflections can be determined by inspection. Alternatively, a composite projection can be

Jan 1, 1965

By James A. Deane

Strip mine reclamation Fs the process of restoring the land affected by the mining process to its most productive use. This can be timber production, pasture, crop land, wildlife and/or recreational use. The mining companies must determine, through the advice of their technicians, what the most advantageous use of the land will be. If the Company does not own the surface, the owner or owners must be contacted to determine their desires as to how the land should be reclaimed. Many times, in making the plans to restore an area with vegetative cover, the watershed and the quality of the water in the area is overlooked. The water itself must be an integral part of the reclamation plan. Many lakes and/or pits can be created with proper planning. In areas in the Midwest, where lakes are a scarcity, these strip mine lakes can become storage reservoirs for large amounts of water, They can help control runoff and low flow augmentation. The strip mining operation will affect the watershed regardless of whether a reclamation plan in made or not. It is up to the reclamation technician to see that the plan benefits the watershed instead of affecting it adversely. This can be done during the operation by intercepting the water before Pt enters the active pit. Diversion ditches above the highwall will handle the runoff water from the watershed. Water that does gain entry into the pit should be removed as quickly as possible. If the rules and regulations adopted by the Ohio River Valley Sanitation Commission in Resolution 5-60 are followed, water encountered during the operation can be handled with little or no adverse effect to the receiving watershed.

Jan 1, 1965

By D. J. Sellmyer

In order to orient single crystals by the back-reflection method it is necessary to know the angles between the various crystallographic planes. These angles have already been published for the hexagonal close-packed metals magnesium, zinc, and cadmium.'

Jan 1, 1965

By Donald E. Grimes

In conjunction with Inland Steel&apos;s development of lead-bearing steels possessing improved machin-ability because of tellurium and/or selenium additions, it was decided to determine liquidus and solidus temperatures in the Pb-PbTe-PbSe sub-ternary system. With the exception of alloys in the PbTe-PbSe system, it is believed that no previous study of this subternary has been performed. Thermal analysis was employed in a general survey of the subternary. In addition to PbTe, PbSe, and pure lead, ten ternary compositions were selected at intervals of ten at. pct. Sixty-gram alloys were prepared by sealing an appropriate mixture of the elements in quartz crucibles with a central thermocouple-well under a vacuum of less than 10 p. All three elements were 99.999+ pct pure with only trace impurities detected by spectroscopic examination. After the alloys had been heated at least 20°C above the liquidus in a Kanthal furnace, cooling and heating curves were obtained. Two or more cooling curves were employed both for the determination of each alloy liquidus and for the solidus of those al- loys containing greater than 50 at. pct Pb. Cooling rates were 0.5° to 3.5°C per min during the 5 min immediately prior to the start or end of solidification. For those ternary alloys containing 50 at. pct Pb, the solidus was determined from heating curves. Temperatures were measured with a Pt/Pt-10 pct Rh thermocouple which was calibrated in the same apparatus against the freezing points of zinc (A. D. MacKay—99.999 pct), antimony (A. D. MacKay-99.999 pct), and copper (ASARCO—99.999+ pct) both before and after the experimentation. The only interruptions in the continuous strip-chart recording of the temperature occurred for brief periods at significant points of interest when direct readings were made with a Rubicon Type B potentiometer sensitive to * 1 µv. The average liquidus and solidus temperatures obtained in this investigation are listed in Table I together with probable errors based on the accuracy of the thermocouple calibration and the reproduci-bility of the data. No chemical analyses of the alloys were performed because the synthetic or as-charged compositions were felt to be reliable. The melting points obtained for PbTe (924.7° ± 0.7°C) and PbSe (1084.0° ± 0.6°C) compare favorably with recent findings of other investigators.&apos;-&apos; As indicated in Table I, both the liquidus and solidus temperatures increase as selenium replaces tellurium for a constant atomic percent lead. As a result, the ternary liquidus and solidus temperatures for a given percent lead lie between the corresponding binary temperatures published in the literature. It should be noted that those ternary alloys containing 50 at. pct Pb exhibit a relatively narrow liquid-plus-solid region (<80°C) when compared with alloys containing greater than 50 at. pct Pb. Alloys with 60, 70, or 80 at. pct Pb not only have a much wider liquid-plus-solid region (>500°C) but also exhibit considerably lower and approximately constant solidus temperatures which thus form a virtually isothermal solidus "plane" slightly below the melting point of pure lead (327.3°C). For these alloys

Jan 1, 1965

By F. W. Jessen, R. W. Durie

The dissolution of salt in the development of salt cavities is controlled by free-convection boundary layer flow along the salt surfaces. It is the purpose of this paper to expand upon results published previously, and primarily to illustrate the influence of surface features on the boundary layer and hence the dissolution process in the development of underground salt cavities. General dissolution equations are presented that apply to a surface inclined to the vertical. A salt surface inclined so as to be overlain by water is dissolved by boundary layer flow, while an inverted surface is dissolved by a combination of boundary layer and cellular flow. Detailed investigation of the boundary layer was limited to laminar free-convection flow. Truly laminar free-convection boundary layer flow may be encountered only in laboratory solution cavities, but the boundary layer will control dissolution even where cavity dimensions are such that free-convection turbulence will occur. The factors found to significantly affect the laminar boundary layer will affect dissolution with a turbulent boundary layer. INTRODUCTION Underground salt cavities have been used extensively for the storage of LPG products, and the use of these cavities is expanding each year. The increasing requirements for such cavities suggest the need for a better understanding of the mechanisms involved, for the purpose of the control of cavity geometry and the most effective use of the injected water. A previous paper outlined a quantitative approach to the determination of salt dissolution rates in the laminar free-convection dissolution of salt. It is the purpose of this paper to expand upon the results previously published and to point out significant factors in the application of these results to the dissolution of field cavities. The dissolution of salt in laboratory scale cavities is controlled by the free-convection boundary layer, which is the region of flow along the salt surface caused by the difference in buoyancy forces resulting from the salt dissolution. The transfer of salt into solution at the salt face causes an increase in salinity, and hence a greater density, in the water at the salt surface. The region of higher density tends to fall through the lighter, less saline water and a flowing boundary layer is the result. The water remains stationary at the contact with the salt surface,l so the resulting velocity profile is such that the influence of gravity is opposed by a viscous shear force at the salt surface. For salt to be transferred into solution from a solid surface to a boundary layer of fluid, it must diffuse through a stationary film of water at the salt contact. According to Fick&apos;s first law, the rate of mass transfer by diffusion is the product of the diffusion coefficient and the concentration gradient, with diffusion transfer in the direction of decreasing salinity. Once the salt has passed into the boundary layer, it will be transferred by a combination of molecular diffusion and convection. The convection transfer will in turn affect the rate of dissolution by influencing the gradient of the salt concentration at the surface. In the previous investigation by the authors to determine the basic mechanism of the salt dissolution process, an equation was developed that agreed very well with the experimental rates of free-convection salt dissolution from a smooth vertical surface. The technique was taken from the work of Eckert2 in the analogous heat transfer system and will be referred to as the integral method. The rate of salt transfer from a vertical section of height H was found to be:

Jan 1, 1965

By J S. Kermeen

This paper deals with drilling and blasting techniques at the Phoenix mine, near Grand F1nks, B.C., which is now operated by The Granby Mining Company Ltd. The difficulties of open-pit mining through former underground workings are unique to this operation. Rock types are related to drilling conditions, and the methods used, or contemplated, to overcome the several difficulties are outlined. The equipment used is also mentioned. Finally, blasting techniques and costs are reviewed. Introduction T HE Granby Mining Company operates on open-pit copper mine and concentrator at the site of the original Phoenix mine, near Grand Forks in south-central British Columbia. The pit is a side-hill cut measuring approximately 1,000 by 2,000 ft., and covering a vertical range of from 4,550 to 4,950 feet above sea level. The mill is currently operating at 1,900 tons per day. A 4.5 to 1.0 waste to ore ratio necessitates the removal of some 15,000 tons of ore and waste per working day. Mining conditions at Phoenix are extraordinary in that all the ore zones currently being

Jan 1, 1965

By B. B. L. Seth, H. U. Ross

A generalized rate equation for the reduction of iron oxide was derived from which two particular equations were obtained: one for rate controlled by the transportation of gas, the other for rate controlled by the phase-boundary reaction. Pellets of pure ferric oxide having diameters of 8.5 to 17.5 mm and a density of 4.8 g per cm3 were prepared and reduced by hydrogen at 750° to 900°C. From the analysis of data obtairzed, it was observed that neither the phase-houndarv reaction nor the transportation of gas controlled entirely the rate of redziction. Rather, the mechanism of reduction can he divided into three stages. In the beginning, the process seems to depend predominantly on the surJrce reaction, hut after a layer of iron is formed the diffusion of gas becomes the controlling factor. Towards the end, however, the rate falls sharply due to a decrease in porosity. The times predicted by the generalized equation for a certain degree of reduction showed an excellent agreement with those obtained experinmentally for pellets of varying sizes. WIDE interest in iron oxide reduction has resulted in many valuable studies pertaining to thermody-namical properties, equilibrium diagrams, and chemical kinetics. Although the thermodynamical properties and equilibrium diagrams are now known with a fair degree of accuracy, the mechanism and rate-controlling step in the reduction of iron oxides presents a problem to research workers which is still unsolved. This is because the field of chemical kinetics is so highly complex. Besides the chemical reaction between oxide and reducing gas, several other processes are occurring simultaneously such as solid-state diffusion of iron through intermediate oxides (FeO and Fe3O4), the diffusion of reducing gas inwards and of product gas outwards, and the sintering of iron if reduction is carried out above the sintering temperature of iron. Furthermore, there is a large number of variables, including the nature and flow rate of the reducing gas, the chemical composition and physical properties of the ore, the temperature of reaction, particle size, and so forth, all of which can affect both the mechanism and the kinetics of reduction. Despite the controversy and diversity of opinion about the mechanism of iron oxide reduction, three main schools of thought have emerged. According to the first, the rate is controlled by the diffusion of gas through the boundary layer of stagnant gas; the second claims that the rate is proportional to the area of the metal-oxide interface, while the third believes the transportation of reducing gas from the main stream to the metal-oxide interface and of product gas from the metal-oxide interface to the main stream to be the rate-controlling step. 1) The boundary-layer theory is true mainly for packed beds where the flow of gas through the bed is important. For a single particle, the boundary layer may be prevented from being the rate-controlling step if a gas flow rate of reducing gas above the critical flow rate is used. 2) Several workers have reported a linear advance of the Fe/FeO interface which provides excellent support for the belief that reduction is controlled by the surface area. McKewanl has given formal shape to this concept with mathematical derivation and has shown it to be valid for reduction of several iron ores, hematite, and magnetite, both by H2 and H2, H2O, N2 mixtures. Some other investigators, however, do not find this theory to be entirely valid. Deviations have been observed2 and further confirmedS3 Hansen4 also agrees that deviations do occur, at least in the latter stages of reduction, while from the data of several investigators summarized by Themelis and Gauvin,5 it is clear that the theory is not always applicable and further that, when it is applicable, it does not hold in the final stages of reduction. 3) Among those who claim the transportation of gas to be the rate-controlling step are Udy and Lorig,6 Bogdandy and Janke,7 and Kawasaki el a1.8 The validity of the theory has also been acknowledged indirectly by other research workers who show that the sintering and recrystallization of iron cause a decrease in reduction rate, for it is only if the transportation of gas is important that this sintering has any bearing. However, the theory has been rejected by some because they have failed to obtain

Jan 1, 1965

By Fred T. Towne

There are a number of air classifiers manufactured throughout the United States and the rest of the world. The classifiers manufactured by Alpine, A. G. of Augsburg, Germany, are unique in their abilities. It is this uniqueness that I wish to delve into and in this respect we will limit this discussion primarily to the classifiers as manufactured by Alpine. It has been reported in the past that these classifiers were introduced into the. United States in the late 50&apos;s. Until the introduction of the Alpine Classifiers, air classification seldom produced a satisfactory fractionation of a product below 45 microns (325 mesh) or above approximately 22 mesh. It has been a common practice to classify fine materials which used water as a carrier medium The use of centrifuges are today producing thousands of tons of finely partitive powders in the very small particle size range. The use of centrifuges in connection with wet grinding mills has increased the rates of production of these mills considerably.

Jan 1, 1965

By T. D. Tiemann

The purpose of this writing is to make available additional data, not previously published, on the extraction of silica from certain iron ores of Wisconsin and Minnesota and to discuss a possible method of processing. Results of investigations on the extraction of silica from low grade iron ores have been previously presented and discussed in detail in AIME Transactions.1,2 All of the ores investigated are essentially nonmagnetic and consist mainly of hematite, goethite and quartz. Much of the quartz is microcrystalline, particularly in the taconites. The ore from the Cuyuna range contains in addition manganese oxides. Briefly, the method consists in digesting a sample of the ore under pressure in a solution of sodium hy-

Jan 1, 1965

By Tilman M. M.

The effects of substituting cobalt for nickel on the acid corrosion resistance of two types of austenitic stainless steel were determined. Cobalt substitutions to a maximum 2.2 weight-percent were made in types 302 and 309 stainless steels. Total immersion corrosion tests were made in 10 volume-percent hydrochloric acid, and boiling-acid tests were conducted in 65 weight-percent nitric acid and in undiluted glacial acetic acid. For modified type 309 in acetic acid, corrosion rates decreased for additions greater than 0.57 weight-percent cobalt. Corrosion rates increased as cobalt was increased up to about 1 weight percent for modified type 302 in nitric and hydrochloric acids and for modified type 309 in nitric acid, but these rates decreased with a further increase in cobalt content. A gradual increase in corrosion rates with increasing cobalt content was shown for type 302 in acetic acid and for type 309 in hydrochloric acid. Cobalt substitutions in larger amounts (above a ratio of 8 Ni to 1 Co) may increase the corrosion resistance of the austenitic stainless steels.

Jan 1, 1965

By J. L. Lytton

The flow-stress recovery of high-purity aluminurn following a 10 pct tensile prestrain was studied in terms of a fractional flow-stress recovery parameter fr. The flow-stress recovery behavior was related to the dislocation arrangements using transmissiort electron rnicvoscopy. During recovery at 120° and 160°C, nearly stable strength levels were attained, the strength level for 120°C recovery being greater than that for 160°C. This stabilization of flow stress was related to the formation of meta-stable dislocation networks bounding nearly perfect cells. Both network formation and the annealing of dislocation loops were found to be recovery mechanisms, and the stronger metastable strength level joy 120°C recovery was related to a smaller average cell size. Analysis of the networks was consistent with the reaction of sets of dislocations with a/2 (110) Burgers vector to give product Burgers DURING isothermal annealing of cold-worked metals, a degree of softening occurs without re-crystallization, and the processes responsible for this change are termed recovery processes. During recovery annealing, the dislocations generated during cold work become rearranged into low-energy configurations, and as much as 50 pct of the stored energy is released."&apos; The relationship between this rearrangement of dislocations and mechanical behavior is of considerable importance, since the dislocation substructures formed during recovery provide a significant degree of low-temperature strength3j4 and can favorably alter the course of primary creep at high temperatures.4 The purpose of the present study was to relate the flow-stress recovery behavior of high-purity aluminum to the substructural modifications that occur. Electron transmission microscopy was therefore employed for direct observation of dislocation substructures at various stages of recovery following 10 pct prestrain. Several investigators5-&apos; have proposed that dislocations can become rearranged or lost during the preparation of thin foils. It was found early in the present study that the dislocation structures in the thicker regions of the foils changed in a systematic way during the course of recovery. Therefore, it is unlikely that substantial losses or rearrangements occurred during thinning. This point will be discussed in more detail later. The results of various investigators indicate that recovery processes in fcc metals can result in release of 50 pct or more of the total energy stored in the as-prestrained metal, this percentage decreasing with increasing prestrain.&apos; Alloying elements or impurities tend to increase this percentage. The release of stored energy of fcc metals during recovery appears to occur by 1) annealing of point defects if the deformation occurred at sufficiently low temperaturesg and 2) rearrangement of dislocations into low-energy Configurations.1,2In bcc metals, the annealing of dislocation loops has also been observed during recovery after prestrain,10-12 and it has been proposed that this is a recovery mechanism for unidirectionally strained fcc metals.&apos; The density of dislocations in bcc metals has not been observed to decrease appreciably during recovery,10 although the formation of regular dislocation networks has been observed. has shown that the formation of such networks can result in elimination of long-range stresses and can lead to significant release of stored energy without dislocation annihilation. It might thus be expected that network formation is a significant recovery mechanism in fcc metals, although extensive network formation has apparently not been reported in controlled recovery experiments. The formation of sub-boundaries in aluminum has been observed by various investigators13&apos;17 during recovery studies of aluminum, but the structure of these boundaries was not resolved. In this regard, it is significant to note that Bailey and Hirsch,&apos; using transmission electron microscopy, detected no network or sub-boundary formation during recovery of 99.99 pct Ag. Furthermore, Clarebrough et al.2 found no such rearrangements during recovery of copper. EXPERIMENTAL PROCEDURE The high-purity aluminum used in this investigation was obtained in the form of 0.125-in.-thick sheet. Spectrographic analysis revealed that the sheet was 99.995 pct A1 with the following weight-percent impurities: 0.001 Cu, 0.002 Fe, 0.001 Si, and 0.0004 Mg. The as-received sheet was in the heavily cold-rolled condition. The as-received sheet was cold-rolled at room temperature to 0.040-in.-thick sheet in the longitudinal direction, which was the original rolling

Jan 1, 1965

By Nicholas J. Grant, Yoichi Ishida, Arthur W. Mullendore

An inert particle -marker technique was developed to provide a direct measurement of grain boundary sliding during creep in tile interior of aluminum specimens. Groin boundary sliding in the interior as measured by this technique was found to be nearly the same or slightly lower than that measured on the surface. These data disagree with those obtained by the grain-counting technique developed by W. A. Rachinger. In tests where both techniques were used, the grain-counting technique gave large and variable values of grain boundary sliding. It is shown that the grain-counting technique gines erroneozcs results because of a preferred direction of grain growth during creep. A question which has long plagued those who study grain boundary creep is whether or not surface measurements yield a true representation of the deformation in the interior of a specimen. The first attempt to measure grain boundary sliding in the interior of a creep specimen was made by Rachinger.1 His technique is based on the measurement of average grain diameters, both parallel and perpendicular to the tension axis, followed by a calculation of the grain elongation from these measurements. The difference between total elongation, Et, and the calculated grain elongation, Eg, is considered to be the result of grain boundary sliding, Egb. Surprisingly large values of Egb/ Et (90 pct) came out of creep tests of pure aluminum at temperatures above 250°C (480°F), utilizing the Rachinger technique. This value is very much larger than the values of 8 to 15 pct measured by numerous investigators on the surface of a specimen. Values obtained on the surface by Rachinger, however, were consistent with those measured by the displacement of reference scratches. Chaudhuri and Grant2 repeated the Rachinger method for A1-10 pct Zn, and found the same large values of Egb/Et inside the specimen. However, from purely geometrical considerations, grain boundaries cannot slide without grain deformation; therefore, they questioned the validity of Rachinger&apos;s grain-counting method. Several authors2,3 have suggested that grain boundary migration during high-temperature deforma- tion may tend to restore the equiaxed grain shape in order to minimize interfacial energy. Rachinger4 tested this hypothesis and found that it did not hold. Grains elongated by rapid extension retained their elongated shape during a subsequent slow creep test. It appears that some other factor was responsible for the abnormally high values of .Egb/El. McLean and Gifkins5 made a survey of the effect of grain size on the ratio Egb/ Et, and proposed that the high values were the consequence of a small grain size. They failed to explain the low value of Egb/Et which Rachinger observed on the surface of the small grain size specimens, and suggested that the surface effect on the value of Egb/Et does not always occur. Many of the disagreements arising from Rachinger&apos; s work stem from the fact that there was only one method of estimating grain boundary sliding in the interior of a specimen, and that method was of an indirect nature. If a marker line of some sort could be introduced inside of the specimen, one could make measurements just as clearly as on the surface. In the present investigation, the technique utilizes a layer of finely dispersed oxide particles inside the specimen introduced by hot press-bonding of two pieces of aluminum. Rachinger attempted a similar technique but with the oxide distribution he obtained there was so much interference with grain boundary motion that quantitative measurements were not attempted. MATERIALS AND EXPERIMENTAL PROCEDURE A) Materials Preparation. Two pure aluminum rods (impurity content in percent: Si, 0.002; Cu, 0.004; Fe, 0.002; Mg, 0.000: Zn, 0.000; V. 0.001) 1 in. diameter by 2 in. high were jacketed end to end in a 4-in.-diam cylinder of commercial-purity aluminum, 4 in, high, which had a l-in.-diam hole. The l-in.-diam mating surfaces of the two pure aluminum rods had been electropolished initially. This interface provided the oxide-film internal -marker plane after the hot press-bonding process, see Fig. 2. The composite was annealed for 1 hr at 900 F and hot upset more than 50 pct reduction in height in one step. The resulting slab was then rolled to 1/2 in. thickness; the pure aluminum test material was cut out and annealed at 900°F for 1 hr and cold cross-rolled to 1/8 in. thickness. The sheet was machined into specimens with a 1/8-in.-square cross section and a 1/2-in. gage length. The following heat treatment was given the specimens: Specimen 5A series: annealed at 1000°F for 5 min for grain-size control and then cooled to 700°F and held for 15 hr for stabilization.

Jan 1, 1965

By K. M. Rolls, R. M. Rose, H. B. Shukovsky

Studies of the phase structure, critical current density, and resistive critical magnetic field of a 45 pct Nb-55 pct Zr superconducting alloy after final-size heat treatments are reported in this paper. A combination of optical metallography, X-ray diffraction, and electrical-resistivity measurements were used to determine the phase structure. Superconductivity measurements, made with heat-treated wires, are correlated with microstructure. Although no quantitative relationship between microstructure and critical current density is found, it is shown that SINCE Kunzler1 as well as Berlincourt, Hake, and Leslie2 first described the high-field, high-current-density superconductivity of Nb-Zr alloys, it has be- the critical current density is highest when the microstructure is finely divided by fibering, coring, precipitation, or fine-scale phase dispersions. The resistive critical field is very sensitive to the compositions of the phases present. Since the alloy investigated here is near the maximum resistive critical field for the Nb-Zr system, any phase decomposition results in a lower H,. Elimination of the effects of cold work lowers H, also. A possible interpretation of the latter in terms of internal surface superconductivity is suggested. come apparent that the resistive critical field and the current-carrying capacity of such alloys are, in large measure, dependent on composition and processing. The resistive critical magnetic field (Hr) for low current densities has been found to increase progressively with zirconium content until a flat maximum is reached between 50 and 65 pet Zr.3 For any single composition, a characteristic maximum value of H, is attained by heavily cold-drawn wire.4 critical current density (J,) depends not only upon cold work but also, apparently, upon microstructure. Heat treatments of cold-worked wires generally

Jan 1, 1965

By P. Shahinian, M. R. Achter

P. Shahinian and M. R. Achter (U.S. Naval Research Laboratory)—We should like to point out another instance where concentration of impurities in grain boundaries led to an embrittlement. In this case an impure nickel (99.8 pct) developed many more in-tergranular cracks during creep in a nitrogen atmosphere than in vacuum.5 In comparison high-purity nickel (99.99 pct) exhibited a much smaller atmosphere effect. We concluded that the interartion of the nitrogen with nitride-forming impurities concentrated at grain boundaries promoted inter-granular cracking.

Jan 1, 1965