Search Documents

President Zakotnik opened the final session of the Institute at 9:30 a.m. Kenneth R. Herrmann of the Resolutions Committee presented the following resolutions to the group for their approval: RESOLVED: That the members of the Rocky Mountain Coal Mining Institute, in convention assembled, hereby ratify and confirm all official actions of the officers, the executive committee and other committees of the Institute between July 4, 1962, and the present time.

Jan 1, 1963

By Ruth F. Brinkley

Principle activities of the Bureau of Mines Explosives Research Laboratory from July 1, 1960 to June 30, 1961 are reviewed briefly in Part 1. Part 1 also includes data obtained in connection with several minor investigations which are not sufficient to warrant separate publications. Part 2 gives brief abstracts of publications that appeared during fiscal year 1961; in general, the research reported in these publications antedates this period.

Jan 1, 1963

By G. T. Krempasky

This report covers the installation and evaluation of lb reinforced concrete sets, 6 in each of 3 mines in the Goeur d'Alene mining district, Shoshone County, Idaho, and is the second of a series to determine the feasibility of a more permanent type of mine support. Closure measurements, where applicable, were made periodically of the concrete-set installations and were compared to the initial cross section of the sets. A different method of blocking was used at each test site; at one test site the type of blocking was changed several times during the test. Results from each test site are reported separately. No attempt was made to compare the cost of the concrete installations with the cost of other types of support used in the district. Such an evaluation of permanent types of support would require a longer period of time. At this time, tests are not complete enough to determine the applicability of underground concrete supports. However, results to date tend to confirm the general opinion that precast concrete mine supports could be used to advantage in openings that require support and must have long life, especially where decay of timber is an important factor.

Jan 1, 1963

By N. Schapiro, R. J. Gray, G. D. Coe

A petrographic and chemical investigation was conducted to determine the occurrence and distribution of the organic and inorganic forms of sulfur in various size and specific gravity fractions of a high volatile, A-rank, Pittsburgh seam coal. The investigation was conducted to aid in the resolution of the problem of how metallurgical coke of lower sulfur content can be produced from high sulfur coals. The Pittsburgh raw coal contains about 2.4% S in two dominant forms: pyritic and organic. Pyritic sulfur constitutes about 57% of the total sulfur in the raw coal and occurs in macroscopic and microscopic-size particles. A plant cleaning process mechanically separates between 50 and 60% of the pyritic sulfur, mainly the macroscopic particles. The organic sulfur constitutes 41% of the total sulfur in the raw coal and 55% of the sulfur in the washed coal. Thus, organic sulfur is not reduced by physical methods of separation. Organic sulfur occurs in all the coal entities, but in general, increases as the exinoid content of the coal increases. In this study, it was found that carbonizing certain selected low gravity coal fractions containing an average of 0.45% pyritic sulfur and 1.01% organic sulfur produced cokes containing an average of 0.22% pyritic sulfur and 0.91% organic sulfur. However, the organic sulfur in the coke is probably derived in part from the heating of pyrite in the presence of carbon. Thus, the total sulfur in the coal carbonized is the most important factor affecting the sulfur content of the coke produced. Concentration of microscopic pyritic and organic sulfur in the middling-type coal indicates the necessity for rejecting as much of this material as is economically feasible. Most of the sulfur introduced into the blast furnace originates from the coke. Although the sulfur content of the hot metal can be controlled by the addition of flux, the flux used restricts the productivity of the furnace by displacing ore and requires first to be smelted; therefore, low sulfur coke is highly desirable. Since the sulfur content of coke is dependent upon the sulfur content of the coals from which the coke is produced, low sulfur coals are required to produce low sulfur coke. In the western Pennsylvania area, large quantities of good coking coal are available from the Pittsburgh seam, but this coal unfortunately contains relatively large quantities of sulfur. To provide information that might be useful in reducing the sulfur content of this coal in the cleaning process, an investigation was conducted to determine the physical and chemical forms in which this sulfur occurs and with what petrographic components it might be associated. The Pittsburgh seam coal, like most other coals, contains two dominant forms of sulfur: one occurs as the minerals pyrite and/or marcasite and is referred to as pyritic sulfur; the other is combined with the coal substance and is called organic sulfur. Pyritic sulfur is amenable to physical methods of separation, whereas organic sulfur is not. Pyritic sulfur particles must be freed from the surrounding coal if they are to be removed in the washing process. Generally, this requires crushing; the required degree of crushing being a function of the size and distribution of the pyrite. The present investigation was conducted to 1) determine the size, distribution and association of sulfur-bearing minerals in the coal and 2) to determine whether the organic sulfur has a preferential association with specific coal entities. If a preferential association exists, this knowledge may be useful in devising a method for organic sulfur reduction. In addition, a study was made to determine the extent to which pyritic and organic forms of sulfur in the coal contribute to the sulfur in the coke produced from this coal. A representative 3%-ton sample of raw coal was crushed to —3 in. and screened into square-mesh sizes: 3 to 1 in., 1 to % in., % to % in., % in. to 10 mesh, 10 to 35 mesh, and 35 to 200 mesh. Separate samples of the -200-mesh fraction and the all-size composite were also collected. Each size fraction (except the -200 mesh) was fractionated on heavy liquids of the following specific gravities: 1.280, 1.300, 1.325, 1.350, 1.375, 1.400, 1.425, 1.450,

Jan 1, 1963

By W. W. Weller

Low-temperature heat capacity measurements were conducted, and entropies at 298.15° K were evaluated for sodium monomolybdate (Na2Mo04), magnesium monomolybdate (MgMo04), and calcium monomolybdate (CaMo04). The 298.15° K entropy values were sodium monomolybdate, 38.1±0.3 cal/deg mole, magnesium monomolybdate, 28.4±0.2 cal/deg mole, and calcium monomolybdate, 29.3±0.2 cal/deg mole.

Jan 1, 1963

By Robert Charles Alfred

Evolution is continuing in the field of rock drilling, Campbell Limestone Company is experimenting in the higher air pressure phase of drilling, It has been determined that there is a definite relationship between Air Pressure, Penetration Rate, Bit & Tool Wear and Life, In our drilling we have determined that &e higher air pressure gives a better penetration rate with less bit wear per foot. Drilling with 180 to 200 PSI air pressure, instead of 100 PSI for air and/or churn drills, has decreased our primary costs by approximately one half.

Jan 1, 1963

By Galen G. Waddell

The Deep Creek zinc and lead mine afforded an excellent example of a relatively small underground mine operation that approached the low mining costs of large, highly mechanized mines, An open stope mining method incorporating sublevel benches and vertical long holes was used (fig. 1). Detailed descriptions are given on the exploration program, stope development, stoping procedures, and pillar removal. Pressure grouting was used to check the inflow of water and thus prolong the life of the mine. Statistics on mining costs and on electric power consumption, haulage from mine to mill, and milling costs are included.

Jan 1, 1963

By Bunting S. Crocker

This paper reviews the trends in the past two years in autogenous grinding throughout the world. It covers rock grinding in South Africa, Sweden, Canada, the United States, Finland and Germany. To properly orient the discussion on this subject, the paper attempts to define and classify the scope of autogenous comminution. As this is a relatively new subject, there is often considerable confusion regarding the various practices, which sometimes differ widely. By clarifying the types and forms, we hope to help clear up this con-fusion. Autogenous grinding is being carried out, throughout the world, either in mills grinding in water or solution or in dry mills using air classification to remove the finished material. The wet grinding, particularly, can be divided into: (1) (2) (3) Primary autogenous grinding, or "run-of-mine" grinding. Secondary autogenous grinding or semi-autogenous grinding or rock pebble grinding. Combination processes. -This covers plants in which pebbles made in the primary mill are re-moved and used as grinding media for fine grinding in secondary mills.

Jan 1, 1963

By G Zahary

THE most acceptable approacl1 to analyzing rock behaviour, at the present time, is based on the application of principles of mechanics and strength of materials. Analyses have been made in which the criterion of failure is based on maximum stress (1) and on Mohr's rupture theory (2). If such analyses are to be carried out, the mechanical properties of the rock must be known within acceptable limits. Although an adequate correlation of laboratory test results with field conditions has not been established, test results have been published (3) on the basis of their comparative value. That is, test results may be useful for comparing the behaviour of different rocks under similar loading conditions or of a particular rock under different loading conditions. This study aims at establishing some of the mechanical properties of an andesite rock by testing specimens cut _from diamond drill core. Drill core (EX) was provided from run-of-mine drilling by New Dickenson Mines Ltd. and Campbell Red Lake Mines Ltd.

Jan 1, 1963

By R. A. L. Black, J. E. Jennings

The problems of slope stability in open cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the orebody. This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ. A company embarking on open cast mining is faced with two basic questions: 1) will the venture be profitable and 2) can it be carried out with safety? The two questions are obviously interrelated because both depend upon the slope angles adopted for the pit. The cost of open cast mining depends largely upon the stripping ratio, defined as the volume of overburden that must be removed to the volume of ore recovered. The steeper the slope angles, the more favorable the stripping ratio, but the stability of the slopes, and therefore the safety of men and materials in the pit, require that the angles be made relatively flat. Consequently, the design depends upon a compromise: the slopes must be steep enough to result in economical mining and flat enough to ensure safety. Today there is a world trend towards deeper mining by open cast methods. This is mainly due to the higher cost of underground mining and the lower cost of open excavation resulting from the introduction of large modern earth and rock-moving machinery. Deeper open cast mining has led to a very great increase in the volumes of wasted overburden, and much thought is being given to the considerable economic benefits which would result if pit slopes could be made steeper by even one or two degrees. The result has been an increasing interest in research into slope stability problems in the expectation that the application of scientific principles will provide solutions leading both to economies and to more predictable operation of the mines. In at least four places, the U.S., Australia, Western Germany and Southern Africa, comprehensive investigations are at present in progress, and it is the object of this paper to review some of the more important aspects of these programs. RELATION BETWEEN ECONOMY OF OPERATION AND SLOPE ANGLES The main object of any industrial enterprise in a free economy is to make a profit. In mining, where profits must be made from a wasting capital asset, a further definition of the profit motive is imposed, namely that the economic aim should be to maximize the total possible profit. But since profits deferred for a number of years are not as valuable as profits that are immediately available, it is usual to discount deferred profits at some rate of interest which reflects their current or present value in the hands of the investor. Thus, in mining the logical aim can be defined more closely still: to maximize the present value of the total future profits. In commercial terms the present value represents the market value of the operation as a going concern. Many factors enter into the forecast of current and future profits. They include the volume of production, the price of the salable product and the cost of production. Current profits can be estimated with reasonable accuracy by the operating engineers; but it is the task of economists and management to assess future trends in the mineral markets and in the economy as a whole, and together with the engineers, they can then estimate the future cost and profitability of the mining operations. In open cast mining, the rate of ore production once decided on remains a virtually constant factor unless a major change in the capital structure of the mine is made. But one factor over which the operator has a considerable measure of control is the ratio of the volume of ore mined to the volume of waste over-

Jan 1, 1963

By J G. Brady

This paper discusses the ceramic products used in the construction industry in Canada, as well as the main raw materials used in their manufacture. The products include the! following: (1) clay prorlucts -such as facing brick (glazed and unglazed), common brick, facing tile (glazed and un-glazed), terra cotta, load-bearing tile, non-load-bearing tile, structural clay floor tile, quarry tile, drain tile, sew-er pipe, conduits .and flue liners -which are made mainly from domes-tic common clays and shales and from domestic or imported stoneware clays and low-grade fire clays; (2) floor and wall tiles of the whiteware type, which are produced from ingredients such as kaolin, ball clay, feldspar, nepheline syenite, talc, pvro-phyllite and wollastonite; (3) glass products -the major ones being sheet glass, plate glass and mineral wool (glass wool, and rock or slag wool) -which are made from such materials as silica sand, soda ash, salt cake, feldsspar, nepheline syenite, dolomitic limestone, high-calcium limestone. borax and (for rock and slag wool) various rocks or slags;

Jan 1, 1963

By D. J. Rose, W. M. Armstrong, A. C. D. Chaklader

The wetiability of single crystals of MgO by specimens of vacuum-cast iron was studied using the sessile drop technique in vacuo at 1550ºC. Formation of FeO at the liquid-vapor interface caused the contact angle (6) to decrease from 117 to 65 deg during the first minute. After cooling, all specimens possessed a peculiar annular interfacial deposit of Fe,O,. Within the annulus the interface showed no sign of chemical attack. Chemical reaction occurred where the iron was alloyed with Ti, V, Cr, Nb(Cb), Ta, cmd Zr. Vnriation of 6 with alloy concentration was studied. Although vanadium md chromium improved the wettability of MgO by iron, the effect of Zr, Ti, Nb, and Ta was indeterminable because the 8 derived from sessile drop considerations was that of the metal against a restrictive peripheral volume of liquid oxide wetting the substrate. INTEREST in the nature of metal-ceramic interactions has been stimulated by progressive development of metal-ceramic combinations. One of the more valuable methods used for bond investigation is the sessile drop technique. Recent attempts to improve wettability through solute additions to the drop have revealed that the solute may a) react with the oxide creating new compounds at the solid-liquid interface, b) adsorb at the interface in a monolayer formation, or c) distribute throughout the drop uniformly causing no wettability variation. This work, part m in a series1,2 of investigations of interface reactions between metals and ceramics, embraces a study of the Fe-MgO system. MgO possesses a large negative free energy of formation (-173 kcal per g mole 0, at 1550ºC) compared to FeO at this temperature (-73 kcal per g mole 02). Hence the electronegativity difference between the drop and substrate allows selection from an extensive group of metal solutes with intermediate electronegativity differences that would, in the absence of chemical reactions, be expected to adsorb pre- ferentially at the solid-liquid interface. However, the high oxygen pressure of MgO in vacuo creates an oxidation environment which influences the solute behavior. Recent studies of the Fe-MgO systemJ74 have been restricted by chemical reactions that obscured observations. In view of the current interest in liquid-phase sintering of metal-ceramic combinations under partial oxidizing conditions,5 a more comprehensive study of the Fe-MgO system seemed beneficial. EXPERIMENTAL PROCEDURE 1) Specimen Preparation. Optical-grade MgO single crystals and Ferrovac vacuum-cast iron were used in all experiments. A spectrographic analysis of the iron indicated 0.008 C, 0.05 V, 0.005 Mo, 0.01 Ti, 0.002 S, 0.01 Cr, 0.001 Mg, 0.01 Si, 0.003 A1 (wt pct). The MgO crystals were cleaved along (100) planes into plates approximately 20 by 20 by 1 mm. Following annealing in vactto at 1100°C for 3 hr, surface irregularities were removed by a chemical etch in phosphoric acid at 100°C. The iron rod was machined into small cylinders approximately 0.250 in. in diam and length and these were carefully cleaned in organic and acidic solutions to remove surface impurities. All specimens were weighed to the nearest 0.1 mg. 2) Apparatus. The apparatus described in detail by previous authors1,2 was modified for this work. A Polaroid Land Camera was incorporated into the optical system so that drop measurements at ten-second intervals after melting were possible with ultra-high-speed self-develop ing film. 3) Procedure. The iron cylinders were placed upright on the MgO plates and positioned in the molybdenum susceptor. After furnace assembly the system was pumped down to a vacuum of 1 µ and flushed with H2 at 800°C. The system was again evacuated to 5 x 10-5 mm of mercury and the temperature raised to 1550°C within 2 min. The molten drops were photographed at appropriate time intervals. TWO min after melting the iron vapor pressure caused gas discharge, or corona, within the tube. The specimens were then slowly cooled to room temperature, sectioned and examined metallographi-cally. X-ray identification of interfacial reaction products was attempted by the powder diffraction technique. Alloying elements (Ti, V, Cr, Zr, Ta, Nb) were added to the iron in various concentrations up

Jan 1, 1963

Jan 1, 1963

By W. L. O?Connell

[Patent Issue No. Date Issued To Subject 386,504 July 24, G. Sweanor The separation of quartz from a 1588 metal with a liquid such as CS2 or CHC13 under water by introducing mixture into water layer. Quartz will stay in water layer while metal sinks through organic.]

Jan 1, 1963

By J. C. Agarwal

A significant portion of the, coal mined by U. S. Steel is beneficiated to upgrade the quality of the resultant coke to meet blast-furnace requirements. Primarily because of degradation from modern mechanized mining methods, a considerable quantity of the coal to be beneficiated is in the 1/4-inch by 100-mesh size range. In the cleaning plants, this coal is usually cleaned on concentrating tables and then mechanically dewatered in solid-bowl centrifuges to 9 to 14 percent water. At some plants, to further decrease the amount of water shipped with coal, and to improve the coking characteristics of the coal at its destination, mechanical dewatering is followed by thermal drying. At U. S. Steel's-Alpheus preparation plant at Gary, West Virginia, approximately 50 percent of the total coal produced is in this fine size range, and two fluidized-bed dryers are used for the thermal drying step. The two fluidized-bed dryers are 14 feet in diameter and were designed by the Dorr-Oliver Company. Although the original design called for a rate of drying equivalent to 37 tons, of moisture per hour, presently they are removing twice that amount. This paper describes, the major problems encountered' in operating these dryers at the present, high capacities and how they were overcome.

Jan 1, 1963

By W. B. Dancy, A. Adams

Laboratory test work on heavy liquid separation of sylvite from halite is reported. Numerous tests were run on sylvite ore sized in the ranges of 4x20 mesh, 10x65 mesh, 8x100 mesh, -8 mesh and -10 mesh with heavy liquids in the range of 2.05 to 2.15 sp gr. From the test results, it was concluded that, with the type of ore under study and a size in the range of -8 mesh, a recovery as high as 90% could be achieved with a product grade of 70% KCl. However, a final product at an acceptable recovery cannot be made with one pass, and the float must either be further processed with heavy liquids or dried and sent to a conventional froth flotation circuit. Potash ores occurring in this country consist essentially of sylvite and halite plus minor amounts of magnesium sulfate salts and montmoril-lonite-type clays. Recovery of potash minerals from evaporite ores in the North American potash fields is accomplished almost exclusively by use of amine flotation. European practice involves froth flotation as well as solution-crystallization processes. Laboratory and pilot plant test work has been reported in Europe and the U. S. on the application of heavy media separation to potash ore beneficiation. Work was probably discontinued because of lack of ore with the required very coarse liberation characteristics (1/8 to 1/2 in. liberation size). Sylvite, with a gravity of 1.99, and halite, with a gravity of 2.17, appear to be ideal for separation by heavy liquids, which are now available in gravities from 1.59 to 2.95. This paper reviews preliminary results obtained from laboratory test work on heavy liquid separation of sylvite from halite. TEST WORK The heavy liquids used in the tests under discussion were chlorobromethane, with a specific gravity of 1.923, and dibromethane, with a gravity of 2.490. These liquids, completely miscible, were combined in the proportions needed to give a mixture having the desired specific gravity. Feed for the laboratory tests was mine-run ore screened to the desired mesh sizes. In conducting the tests, the sample was fed at a constant rate into a stream of heavy liquid and the mixture directed into a small separatory vessel. The float overflowed into a collecting pan while the sink collected in the bottom of the separatory vessel and was removed at the end of the test. Approximately 500 g of feed constituted a charge. Pulp density of the feed was kept low to prevent particle to particle interference in separation. With feed in the range of 8x100 mesh, a pulp density of under 10% solids by weight was found advisable. With coarser feed the pulp density could be carried as high as 15% solids. Time of separation was very rapid. In the case of 4x20-mesh material, separation was effected in 15 to 30 sec; with -10-mesh feed, separation required about 1 to 2 min. SPECIAL EQUIPMENT Since heavy liquids are toxic to varying degrees, all separatory work was carried out in a standard laboratory fume hood. It was noted that complete removal of fumes was not being effected; therefore the hood construction was modified, resulting in a completely satisfactory arrangement for heavy liquid test work. In the interest of safety, details of this fume hood are reported here. Unlike most fumes, heavy liquid fumes tend to settle and flow like water, rather than to rise like a gas. Working on this assumption, a standard water drain was installed in the hood. Across the front of the hood a 1-in. barrier was constructed. In the rear of the hood a false back was installed, with an adjustable sliding door on both the bottom and top of this panel. As shown in Fig. 1, the exhaust fan pulled a vacuum behind the barrier, sucking the heavy fumes from the bottom of the hood. Another addition was the drying box, shown to the right of the hood. This is simply a box covered on top with hardware cloth and connected by a 6-in. inlet to the hood. Sample trays made of fine mesh wire filter screens were found ideal for drying samples. With this arrangement, air flowed completely through the sample and all fumes were drawn into the hood. In use, it was found effective to cover with a

Jan 1, 1963

By F. Taylor Ostrander

Some countries are infinitely poorer than others in mineral resources-despite the perfect equality of their political leaders ambitions. Compare the mineral poverty of Kenya and Tanganyika with the riches of Katanga Province and Northern Rhodesia. Compare Paraguay with Chile, There never has been any equality in the distribution of nature's wealth. Minerals cannot play any role at all in economic development where they don't exist, and there are bound to be differential rates of economic development where there are basic differences in the wealth of mineral resources available. Africa is my principal area of interest and I know that there is an unfortunate but widespread misconception about Africa's "vast mineral resources, "its "untapped mineral wealth." Why is it untapped? Why is it undeveloped?

Jan 1, 1963

By G M. Young

IT IS most appropriate that this first Memorial Lecture should be given in the Province of Quebec, near the site of the first metallurgical industry in Canada. At La Forge, about seven miles north of Three Rivers, iron was produced in 1783. We are told that the early settlers obtained most of their iron-ware -stoves, kettles, axes and ploughshares -from this smelter, with its foundry and forge. The Canadian copper industry also had its beginnings in Quebec when, nearly 100 years later, in the 1880's, several small copper smelters were erected in the Eastern Townships. Later, in 1899, Canada's first aluminum smelter was built at Shawinigan. From these small beginnings has grown a vast metals industry, the export value of its products being only exceeded by that of our forest products -newsprint, pulp-wood and lumber. As we are not a large country in terms of population, our domestic capacity to consume is often small in relation to our developed capacity to produce.

Jan 1, 1963

By M. L. Pearce

A comparison of the isotope-dilution, vacuum-fusion, and chemical methods of analysis for nitrogen in Si-Fe is made with particular emphasis on the effect of sample history. The superiority of the isotope-dilution method from the point of view of 1 HE analytical techniques used to determine nitrogen in Si-Fe have been subjected to close scrutiny in recent years primarily because of the marked influence of the element on the properties of the alloy. These investigations have led to a diversity of opin- both precision and accuracy is demonstrated. The solubility of nitrogen in 3.06 pct Si-Fe is investigated and the effect of silicon content on the activity coefficient of nitrogen is derived. ion regarding the reliability of the vacuum-fusion and chemical methods of nitrogen analysis when applied to si- Fe.'-' A majority of workers appear to favor the vacuum-fusion method over chemical methods particularly in those cases where part of the nitrogen may exist as silicon nitride or the total nitrogen content is very low. Contrary views have been expressed, however,' and it has been demonstrated that for some Si-Fe alloys both methods yield results which are significantly lower than those

Jan 1, 1963

By George H. Holmes

This report describes the results of a reconnaissance survey of areas in California and Nevada considered favorable to beryllium mineralization. Pegmatite dikes, veins, intrusive sills, contact. metamorphic, and disseminated deposits as well as tactite deposits in the former major tungsten-producing districts were investigated. A general geographic pattern of beryllium mineralization was found to be concentrated along a wide belt in eastern Nevada extending from the Ruby Mountains, Elko County, south through the Fish Creek Range, Eureka County, the Snake Range, White Pine County to the Virgin Mountains in Clark County, Nev., and Mohave County, Ariz. Sporadic occurrences of beryllium are in central and southern Nevada, and in the pegmatite dikes of San Bernardino, Riverside, and San Diego Counties, Calif., and the granite masses of the southern Inyo Mountains, Inyo County, Calif. Principal company activities are centered in the Snake Range, Fish Creek Range, and the Virgin Mountains, Nev., and the Inyo Mountains, Calif. Other areas in California and Nevada have been superficially explored with results indicating either limited or widespread, but submarginal, mineralization. Although beryllium was found to occur, to some extent, in many of the deposits, mining has been hindered by the lack of a market for beryllium ores and concentrates other than standard-grade beryl and also by the erratic pattern of mineralization and the high exploration and beneficiation costs required to produce a marketable product.

Jan 1, 1963