Search Documents

By R. C. Neavel

One of the most important requirements to be met by any coal producer is delivery of size consists tailored to specific applications. Generally these specifications include a minimum as well as a maximum size limit. The customers of a major Indiana coal producer noticed that some shipments of sized coal contained a large proportion of undersize pieces. Also, in these shipments, the pieces which remained within the specified limits were cracked and, when handled, crumbled readily. The producer, certain that these shipments had been properly sized at the tipple, suspected that degradation had occurred in transit. The Indiana Geological Survey was requested to examine the coal from one of these shipments to attempt to determine the cause of breakage. Two basic facts about coal and coal seams led to the employment of petrographic techniques in this investigation. First, all coal seams consist of accumulations of diverse organic and inorganic constituents; and second, most coal breakage, either desirable or undesirable, can be attributed to the inherent weakness of some of these constituents or to poor adhesion between certain constituents. Analyses of degraded coal Sampling: Samples were secured from 2 stock piles of 2-by 4-inch coal in a dealer's yard. The coal in both piles had received the same treatment from mining to storage, although it had been mined and shipped on two different days. The size consist of one pile, however, appeared smaller than that of the other. The sample from the degraded pile is referred to as the slack sample, and the other is called the unslack sample. Size analyses: In order to determine the actual size consist, the samples were screened, with a minimum of rough handling, on square 2-inch, 1-inch, 1/2-inch, and 12-mesh screens. It is assumed that 100 percent of the 2-by 4-inch coal is retained on a 2-inch round screen at the tipple. Analyses of several loads at the tipple indicate that approximately 26 percent of the 2- by 4-inch coal, 100 percent of which was assumed held on a 2-inch round screen, passed through a 2-inch square screen. Twenty-six percent may be taken as the normal difference between round and square screens. Results of the analyses of stockpile coal are shown in Table 1. Cumulative percent versus size are plotted on a Rosin-Rammler chart as Figure 1. Both samples approximately follow normal size distribution; this indicates that breakage is not size preferential and also that the samples are representative of the stockpiles. Although both samples exhibit the same general size distribution, the median size of the slack sample is considerably smaller than that of the unslack sample. Fifty-five percent of the unslack sample was undersize (29 percent greater than the normal 26 percent difference), and 83 percent of the slack sample was undersize (57 percent greater than the normal 26 percent difference). Both piles contained a greater percentage than normal of undersize coal; this indicates that they were both affected by degradation, but to a different degree. Bedding-plane analyses: Coal, because of its laminated nature, will break preferentially along bedding planes, especially where adjacent constituents are poorly cemented to each other. Subsequent breakage perpendicular to the

Jan 1, 1961

By Marvin L. Whisman

Several parameters controlling the reproducibility of tritium determina¬tion in organic compounds by liquid scintillation counting were evaluated by the Federal Bureau of Mines. These included optimum volume of scintillator solution for maximum counting efficiency, reproducibility of counting a sealed commercial standard and comparison with duplicate counts on laboratory-prepared samples. The error introduced by using microliter pipets, optical differences in counting vials, reproducibility of counting organic samples where quenching is a factor, reproducibility of counting laboratory-prepared samples with an added internal standard, optimum ratio of internal standard activity to sample activity, effect of sample volume upon counting efficiency, count rate at which coincidence losses become apparent, and reproducibility of organic compound radioassay by the standard addition technique are outlined. From the evaluation of these parameters, a technique that can be applied routinely to organic compounds containing tritium has been established, and details are included in this report.

Jan 1, 1961

C. G. Dunn (Generai! Electric Research Laboratory)— The author is to be commended on his attempt to calculate the residual strain energy from information on the dislocation density within the subgrains and a surface energy associated with the subgrains. However, much closer agreement between a calculated critical size of a nucleus and the observed size of grains that did not continue growing can be obtained if a reasonable correction is made in obtaining the energy of the surfaces of the subgrains. For example, since the sample is a single crystal with a cold-rolling reduction of 70 pct in thickness, one needs either an average disorientation for this or an average subgrain boundary energy rather than the 2.5 deg disorientation of a bent crystal, which was used by the author. From either the Laue photographs of the author or the pole density plot of Koh and Dunn 16 for a (113) [332] cold-rolled crystal the

Jan 1, 1961

[NORTH AMERICA UNITED STATES Alabama BIRMINGHAM BURROWS, WILLIAM C. CORD, RICHARD H. COSTON, OTIS D. JR. FAIRHOPE RUFFLES, WILLIAM R. HUNTSVILLE WAGGONER, JERRY B. MOBILE PETROUTSON, PETER C. SELMA JONES, JAMES J. JR. UNIVERSITY CUDWORTH, JAMES R. JONES, WALTER B. RICHARDS, EDWARD F.]

Jan 1, 1961

By J. R. Lucas, R. L. Frantz

Mine sealing programs for the alleviation of acid mine drainage were begun by the Federal Government in the '30's. As part of an acid mine research project to The Ohio State University, a field test was undertaken to determine the effectiveness of mine seals for reducing mine acid. Details of the tests made at the McDaniels mine show the feasibility of air-sealing and flooding an acid-producing drift coal mine. Work by the University continues. The Federal Government undertook in the early thirties an extensive mine sealing program for the alleviation of acid mine drainage. In the states of West Virginia, Ohio, and Pennsylvania many general summaries have been made on this program but no critical evaluation with supporting data has been found on the effectiveness of mine seals for reducing mine acid. Because of this it was decided to undertake a field testing program as part of an acid mine research project of the Engineering Experiment Station, The Ohio State University. The objective of this phase of the project was to develop and install a field research laboratory for acid mine drainage studies. Specifications for such a mine laboratory were developed and resulted from the following considerations: 1) Size and preservation—the test mine shou1d be of limited size to permit frequent and detailed examinations; it should be in a reasonably sound condition to permit safe entry. 2) Isolation—the mine should be physically separated from all other mines. 3) Openings—a minimum number would be desirable to reduce the sealing problem. 4) Structure—the mine especially near the openings should be structurally sound. 5) Acid production—the mine should be producing significant quantities of acid. After considerable searching, the McDaniels mine was selected in the Hocking coal field in Vinton County just above Lake Hope State Park in southeastern Ohio. The small drift mine in the middle Kittaning coal consisted of two small rooms with one mine opening about 6 ft above a seasonal stream bed. Before it was finally decided to seal the mine, a short study was made of the acid drainage over several months. Fig. 1 shows a plot of acidity (milligrams per liter), flow (gallons per minute), and acid production (pounds per day) vs time over the sampling period. Because the coal was overlain with a porous sandstone, the mine drainage was consistent the year around even though the mine was

Jan 1, 1961

By F. H. Buchella, J. F. Buchanan

The San Manuel copper deposit is located about 45 miles northeast of Tucson. The concentrator, smelter, administration building, and other plant facilities are located about seven miles southeast of the ,nine area at the new town of Sari Manuel as shown on Figure 1 (Sketch).

Jan 1, 1961

By W. C. Thurber, C. J. McHargue

THE deformation textures of metals have been extensively studied because of both the practical implications in metal fabrication and the fundamental insight into the behavior of the metal during deformation. Most studies have been concerned with pure metals or solid-solution alloys and relatively little attention has been directed toward more complex alloy systems. Barrett' and Brick2 have summarized work on multiphase systems in terms of the relative ease of deformation of the phases. Thus, if the phases are deformed about equally, each develops its usual texture for the particular fabrication process. This behavior has been reported for Ag-Cu and Cd-Zn alloys3 and 62-38 brass.4 A dispersion of hard particles in a softer matrix interferes with the normal reorientation of the matrix lattice during deformation, thus distorting the texture or in some cases preventing its development. Increasing the amount of carbon in steel has been observed to increase the randomness of the ferrite5 and almost random textures have been reported for A1-12 pct Si eutectic alloy wires.6 It has also been noted that if the second phase is platelike, deformation causes the platelets to line up in a common direction. The present work concerns a quantitative study of the deformation textures in aluminum-uranium alloys containing 5 or 13 wt pct U. Alloys in this composition range are characterized by a pure aluminum matrix in which the intermetallic compound UA14, is dispersed. From a fundamental standpoint, this system affords the opportunity for studying the effects of a dispersed phase on texture development in an essentially pure metal matrix. Further, these alloys are commonly used as fuels for nuclear research and testing reactors, and a knowledge of the preferred orientation may be useful in evaluating physical and mechanical properties as well as response to fabrication. The deformation textures in sheets of aluminum (99.996 pct), Al-5 pct U alloy, and Al-13 pct U alloy were determined for reductions in thickness of 90 pct by cold rolling. The texture in an alloy rod of the latter composition which had been extruded at 455°C was also determined. It can be readily ascertained from the aluminum-uranium phase diagram that the 5 pct U alloy is hypoeutectic and contains 7.3 wt pct (3.4 vol. pct) UAl4. The 13 pct U alloy has the eutectic composition and contains 18.9 wt pct (9.4 vol. pct) UAl,; however, because of nonequilibrium solidification conditions, the typical eutectic microstructure was not developed. The alloys were prepared by open-air melting in graphite crucibles. The slab castings were cropped and cold reduced 90 pct in thickness on a two-high mill. The slabs were reversed after each pass. Although the uranium-bearing alloys exhibited edge cracking, they could be cold rolled to the desired thickness. Small coupons 1.5 by 0.75 by 0.1 in. thick were sheared from the center of the rolled plate with a major axis parallel to the rolling direction. To obtain a specimen of sufficient thickness for machining of the X-ray diffraction specimen, three coupons were laminated into a single three-ply sandwich with a suitable adhesive. Adhesives which could be cured at room temperatures were selected in order to prevent recrystallization during bonding. Bondmaster M-648 (Rubber and Asbestos Corp.) was used for the pure aluminum laminate and Armstrong A-6 (Armstrong Products Co.) was used for the alloys. The alloy for extrusion was cast in a cylindrical graphite mold! cropped and machined into a 3-in. diam by 4-in. long billet. This billet was preheated to 455°C, upset to 3.125 in. diam, and extruded on a 700-ton hydraulic press at a speed of 6 fpm through a flat-face, 1-in. diam die. The rod was quenched with a water spray as it emerged from the die. Pole-distribution data were obtained using the diffractometric method described by Jetter and Borie.7 A spherical X-ray diffraction specimen of

Jan 1, 1961

By A. Boltax

Precipitation processes occurring during both furnace cooling and aging of copper-iron albys were studied by means of electrical and magnetic measurements. On furnace cooling, two distinct stages in the precipitation process were detected; one occurring above and the other below 850° C. The kinetics of precipitation from quenched alloys were studied between 200° and 700°C. The reaction appears to be consistent with the concept of tmcleation of precipitate particles at dislocation loops formed by the clustering of quenched-in vacancies. A study Of in copper-iron alloys is particularly interesting because the combination of magnetic and electrical properties in these allovs provides a quantitative means of following the course of the precipitation reaction. (The details of precip-

Jan 1, 1961

By D. R. Cook

This paper is a case history of an exploration venture for base metals, begun by the Rocky Mountain District of Bear Creek Mining Company in 1952 and completed in 1954. The project was based on the idea of W. S. Burbank, U. S. Geological Survey, that commercial deposits of base metals might occur in Paleozoic sediments beneath hydrothermally altered volcanic rocks in the Southern Bonanza mining district, Colorado. Here, an area of andesitic rocks, four square miles in extent, has been argillized, pyritized, chloritized and silicified. Geological, geophysical and geochemical studies were followed by the diamond drilling of three holes totalling 6,220 feet. Further alteration ang geochemical studies were made on the cores from these holes. A brief review of the alteration and geologic mapping, colored aerial photograph interpretation, geochemical soil and rock sampling, magnetic, gravity and radio-metric surveys are presented together with some conclusions regarding this work. This paper is a case history of an exploration venture for base metals, begun by the Rocky Mountain District of Bear Creek Mining Company in 1952 and completed in 1954. Important contributions were made to the project by personnel of the Rocky Mountain District and the Geophysics Division. Individual acknowledgements to these people are made at the end of the paper. BASIS FOR THE PROJECT The project was based on the idea of W. S. Burbank (1947, p. 444) that commercial deposits of base metals might occur in Paleozoic sediments beneath hydrothermally altered volcanic rocks in the Southern Bonanza mining district, Colorado. Paleozoic sedimentary rocks, including the favorable Leadville limestone, are exposed three miles south of the altered area, and reason exists to believe that they might underlie it within a reasonable depth. Alteration of pre-mineral volcanic rocks has been used successfully as a guide to concealed orebodies in the Main Tintic and East Tin tic mining districts, Utah (Bill-ingsley, 1933, p. 120-122; Lovering et al, 1949; Howd, 1957, p. 124-134; Cook, 1957, p. 73) and could be a useful guide here. GENERAL GEOLOGY AND STRUCTURE The Northern and Southern Bonanza mining districts are northwest of the San Luis Valley in southern Colorado, just within the northeastern edge of the San Juan volcanic province. The districts are1ocated on the southern extension of the Sawatch uplift, a prorninent northwest-trending structural high. The highly productive mining camp. of Leadville, Gilman and Aspen are on the northeastern and northwestern flanks of this uplift where Paleozoic limestones have

Jan 1, 1961

Recent literature is reviewed with emphasis on the design and scale up of mixers. Most important aspects of mixing have resulted from the study of Newtonian fluids and only a minor attempt has been made to extend the work to non-Newtonian materials.The rheology of non-Newtonian materials is outlined and the typical behaviour of mineral slurries is indicated.The importance of flow velocity, flow pattern, and fluid turbulence is discussed with relation to suspension of solids and rate of reaction.Data on experimental leaching of ore from Mary Kathleen, Queensland, show the effect of different mixing impellers.In conclusion, factors involved in the selection of a mixer are presented with emphasis on economic appraisal after pilot experimentation.INTRODUCTIONThe subject of mixing has attracted considerable attention during recent years, but relatively little work has been undertaken for the study of non-Newtonian materials. Most work has been restricted to Newtonian fluids because there are less inconsistencies in such study.Mixing, by definition, implies blending or combining, and ranges from gentle mixing which blends the contents of a large tank in 24 hours to violent mixing which completely homogenises the contents of a tank within seconds. Metzner and Otto (1957) have pointed out the present lack of knowledge on the degree (or quality) of mixing. Apart from this fact the design of mixers for Newtonian materials would seem to be reasonably certain.Both capital and operating costs rise rapidly with increasing mixer size. Therefore the design, or selection, of a mixer is a matter for economic consideration in the overall aspect of plant design and operation.

Jan 1, 1961

By J. C. Humbert, J. F. Elliott

The solubility of nitrogen in liquid pure Fe, Cr, and Ni, in liquid Fe-Ni, Fe-Cr, and Ni-Cr alloys and Fe-Cr-Ni alloys, has been measured by the Sieverts' type apparatus between 1500° and 1800°C. Tabulations and graphs of the solubility data and activity coefficients are shown. Heats of solution are reported. Interaction coefficients of the several elements in Fe. Cr, and Ni ave also reported. THE solubility of a gas in a liquid metal is usually measured by either the quenching technique or the so-called Sieverts' method. In the quenching method, 1-3 the melt is equilibrated at the desired temperature and pressure with the gas phase having a known fugacity of the gas being studied. The melt is sampled and the sample is quenched and analyzed chemically for its gas content. In Sieverts' method the melt is contained in a closed chamber. The apparent volume of this chamber, i.e. the "hot volume," is usually determined by introducing a known quantity of an inert gas having very closely the same physical characteristics as does the experimental gas. Alternatively, the experimental gas is used with an inert specimen having the same general physical characteristics as does the experimental melt. Subsequently, the experimental melt is equilibrated with the experimental gas by introducing a known quantity of the gas into the calibrated chamber. The solubility of the gas is obtained from P-V-T relationships. The quenching method suffers from' the limitation that some gas may be gained (as in the case of Cr-Fe alloys) or lost (as in the case of Fe-Ni alloys) during solidification and cooling of the sample. With Sieverts' method sampling and analysis are unnecessary. However, errors can result from the difficulty of determining accurately the "hot volume,"

Jan 1, 1961

By E. G. King

In continuation of the study of thermodynamic properties of the common interoxidic compounds of ferroalloy elements, this report gives the results of low-termperature heat-capacity measurements and entropy evaluations of the monotungstates of sodium, magnesium, and calcium. Previous reports4 5/ of this laboratory dealt with low-temperature heat capacities, entropies, and heats of formation of the sodium vanadates. Heat-capacity measurements of the monotungstates of sodium, magnesium, and calcium (Na2W04, MgW04, and CaW04) were conducted throughout the temperature range 51° to 298° K. The entropies at 298° K. were evaluated and then combined with entropy data for the elements and oxides to obtain entropies of formation. This information is an essential part of the data needed for thermodynamic appraisals of chemical reactions of these substances. No similar data for any tungstate are to be found in the literature.

Jan 1, 1961

By R. E. Hudrlik, G. W. Preckshot

The diffusion coefficients of silver from solid silver in molten lead were measured to within ± 0.8 pet in a columnar type diffusion cell ower, the temperature range of 326° to 530°C. Fick's law describes the process up to 530°C where the laminar mechanism appareltly breaks down. These is negligible resistance at the interface as shown by mathematical analyses. The diffusion coefficients are found concentration independent. IT would seem that diffusion in liquid metals would be free of such effects as molecular structure, dissociation. polarization. and compound formation. This view was taken by Gorman and preckshot in their study of diffusion of copper from solid copper into molten lead. They reported diffusion coefficients which were independent of the concentration over the range of 478° to 750°C. They found that the Stokes-Einstein equation with constant radius of the diffusing specie represented the diffusion data better than Eyring's rate theory equation and Sheibel's correlation. The radius of diffusion was found to be that of the doubly charged copper. There appeared to be no resistance across the solid-liquid boundary. In the present work the diffusion coefficients for silver in liquid lead were measured over a range of temperatures of 350° to 505°C. The solubility of silver in lead over the range of 303° to 630°C was also obtained. These results are compared with calculated or correlated values or with data in the literature. EXPERIMENTAL Procedure—The experimental equipment techniques and procedures were those reported in detail by Gorman and preckshot9 and will not be repeated here. Measured values of WT, Co, A. L were obtained for various diffusion times and the diffusion coefficient was computed for the case of no resistance at the interface9, 11 by: WT/CoAL = 1- 8/p2 n=1 1/(2n - 1)2 exp[-(2n - 1)2p2 Dt/4L2] [1] or where there was resistance at the interface by: WT = 1- ?n=1 2h2/ap2L [sxp [-Dan2t]/[(h2 + an2) L + h] The roots an are those of the transcendental equation3 tan (an L) = Iz/cun. The diffusion coefficient is that defined by Hartley and Crank.7 The total silver in the lead cylinder and equilibrium slug was determined by a cupellation technique' with proper correction for losses. Analysis of known samples showed that this method is surprisingly accurate. The amount of silver in the lead adhering to the silver cylinder was obtained in the same fashion as shown by Gorman and preckshot.9 The small errors involved in this determination are not critical since the silver in this adhering lead layer is only 3 to 15 pet of the total diffused. Materials—Electrolytic silver containing 99.9+ pet Ag obtained from General Refineries of Minneapolis, Minn. was used for all but runs 7 and 8. For the balance of the runs this silver was reduced with hydrogen at 1100°C and its oxygen content was found to be about 0.017 pet. For the runs. 7 and 8, phosphorous-reduced silver of the same purity was obtained from Handy and Harman Co. of Chicago, Ill. The densities of the phosphorus-reduced silver and the hydrogen-reduced electrolytic silver were 10.484 and 10.487 g per cm3, respectively. These values agree with those reported for pure silver. Silver which was reduced at 900 C had an average density of 9.998 g per cm3, indicating porosity. This silver was used for a number of runs which were not tabulated in Table I. These are indicated by crosses on Fig. 2. The 99.999 pet Pb was obtained from the National Lead Co. Research Laboratory of Brooklyn, New York. DISCUSSION OF RESULTS The diffusion and solubility results are reported in Table I for eleven runs using either phosphorus-reduced electrolytic silver or hydrogen-reduced silver at 1100° C. The solubility data shown in Fig. 1 show the excellent agreement with that reported by Heycock and Neville.8 The data of Friedrichs5 apparently are in error. The experimental solubility data of this work are reported to 0.3 pet. The experimental diffusion coefficients computed from Eq. [1] are reported within 1.2 pet of the mean and are plotted in Fig. 2. These are expressed within +0.8 pet of the experimental values over the entire temperature range by: D= 8.26 x 10 -5 e-1925/RT . [3] There appears to be little difference due to the

Jan 1, 1961

By R. M. Porter

PILLAR extraction at the Sullivan Mine bas been in progress for over twenty-five years and bas .involved progressively larger pillars. The largest pillar blasted to date exceeds one million tons and is described in this paper. This blast is believed to be one of the largest to take place entirely under-ground. The Sullivan Mine, owned by The Consolidated Mining and Smelting Company of Canada Limited, is located in the southeastern corner of British Columbia on the east flank of the Purcell range overlooking the twenty-mile wide Rocky Mountain Trench (Figure 1). The orebody is a bedded replacement deposit in argillites, varying in thickness up to 300 feet, but averaging about 80 feet. Above the 3900 Level, the dip varies from nearly horizontal to 40 degrees; be-low the 3900 Level it varies from 45 to 20 degrees (Figure 2). Pillar extraction follows a plan of retreating outward from caved areas. The size of each blast is determined by the effect which the removal of support

Jan 1, 1961

By R. E. Boehler, N. C. Ludwig

At Buffington Station, Gary, Ind., Universal Atlas Cement operates fourteen 8 x 101/2 x 155-ft cement kilns in mill 6 and two 11 x 360-ft kilns in the Harbor plant. The No. 11 and 12 kilns in mill 6 are equipped with Manitowac recuperator sections. This report describes studies in measuring exterior shell temperatures on several of these kilns and the development of a traveling radiation pyrometer with certain novel features. Preliminary Work: At first various temperature-sensing devices were placed on the steel shell: 1) crayons with calibrated melting points, 2) colored paints with temperature-calibrated pigments, 3) aluminum paints with temperature-calibrated binders, and 4) metal-stem dial thermometers. The colored paints and aluminum paints failed to indicate the temperatures correctly. The crayons and thermometers did indicate fairly correct temperatures, but it proved impossible to apply enough of these on the shell to detect all the potential areas where hot spots might develop. Furthermore, considerable labor was required to apply these sensors and read the temperatures. Consequently no further work was done with these devices. Formation of Hot Spots: In the burning or clinker-ing zone of a cement kiln, the thickness of the protective coating and thickness of the brick govern the amount of heat transmitted to the steel kiln shell. Usually the protective coating consists of 4 to 8 in. of fused cement clinker. The formation of a hot spot is usually caused by loss of coating? that is, localized areas of the coating become thin or fall away from the refractory. This is generally caused by excessive temperature in the burning zone over a fairly long period of time. It may also be caused by a sudden thermal change in the burning zone. Variations in raw feed composition and in feed rate require changes in the fuel and air rates, and when these are not appropriately altered, conditions may develop in the kiln that will result in loss of coating. Luminescence on the kiln shell indicates that a hot spot has developed to a point that usually alters the refractory's thermal conductivity properties. When this thermal weakness zone occurs in the burning zone of the kiln, constant vigilance is required to protect it by maintaining proper coating. Even so, it has been the writers' experience that within a period of several days to about four weeks the hot spot usually recurs with greater severity. This necessitates shutting down the kiln and re-bricking the affected area. One of the prerequisites of a good burnerman is the ability to maintain a protective coating despite the many variables in operation. When he knows that it is getting thin or that an area has dropped off, he reduces the firing rate and kiln speed and brings feed into the affected area in an effort to rebuild the coating. But when powdered fuel is burned, the atmosphere of the kiln may prevent the burnerman's observing the condition of the coating closely at all times without taking off the fire. It is not considered good practice to do this frequently, as it imposes a thermal shock on the coating and upsets operation of the kiln. To help the burnerman scan the shell of the kiln along the burning zone, therefore, a radiation pyrometer, connected to a potentiometric recorder, was mounted on a slowly moving steel cable. The theory of operation, construction details, and adaptability of the radiation pyrometer are included in an excellent monograph' and also in a textbook.' Shell temperatures of the Atlas Cement kilns were measured with a Brown Instruments Div. low intermediate range Radiamatic unit, of range 200" to 1200°F, and a circular chart Electronik potentio-metric recorder, of range 500" to 1000°F. In Bulletin 59095M the supplier publishes standard calibration data (millivolts vs degrees Fahrenheit) for this radiation pyrometer, These data, however, apply only to flat surfaces having emissivities of unity. Calibration of Radiation Pyrometer for Use on Curved Surfaces: When applied to surface temperature measurements, the radiation pyrometer reading depends on the nature of the surface, the material of which it is composed, and also to some extent on the temperature of the surroundings. Although the present radiation pyrometer is designed to give a calibrated response under ideal (black body) conditions when used commercially, it must be calibrated empirically. The calibration procedure, given below, follows that described by Dike (Ref. 1, pp. 38-39). Calibration tests on plane and curved surfaces showed that the response of the radiation pyrometer was very

Jan 1, 1961

By T. M. Kegley, J. H. Frye, D. L. McElroy, M. L. Picklesimer, E. E. Stansbury

Measurements of rate of growth, thermodymmic quantities, and partitioning of Mn are reported for high-purity eutectoid Fe-C and Fe-C-Mn steels for the auistenite-pearlite reaction. Evaluztion of the cotnstants of a derived-rate equation with these data indicate that Mn additions cause the decrease observed by increasivg the activation energy and apparent activation entropy or the movenment of complexes at the interface. A diffusion-controlled mechanism is not required. Appreciable partitioning of Mn to cementite occurs entirely behind the austenite-pearlite interface for more than 30°C of subcooling. ThE growth of pearlite from austenite has been extensively studied over a period of years. but the rate-controlling step in the process is not known nor is the mechanisrn of the effect of alloying elements understood. A comprehensive review of the subject has been given by Mehl and Hagel. The present study has been concerned with further considerations of the effects of alloying elements on the rate of growth of pearlite. Analytical relatioriships for the rate of growth of pearlite have been considered by Zener.2 Turnbull,3 Machlin,4 Cahn.5 Frye,6 and Frye et a1.7 The derived expressions in each case involve the free energy of the transformation. the interlamellar spacing. and some rate term of the nature of the diffusion coefficient. mobility or frequency of occurrence of some rate-determining step. The treatments. of course. differ in detail. Further consideration is given in the present paper to the equation of Frye, Stansbury. and McElroy which was derived from modified absolute rate theory without in any way specifying the mechanism of the reaction. This equation is r=c ? T ? F exp -?E*/RT [1] where r = rate of growth in mm/sec c = a constant AT = equilibrium transformation temperature minus actual transformation temperature "C ?F = free energy per mol of austenite minus that of pearlite ?E* = activation energy R= gas constant ?F in Eq. [1] is computed from the following: ?F=?H?T/To - ?T' dT' ?T' ?CdT"/T" [2] To To where AH is the enthalpy per mol of austenite minus that of pearlite at the equilibrium temperature, To, and AC is the difference in specific heat between austenite and pearlite per mol. Subsequently, Darken, Fisher, and Galligan8 have reported that a layer of ferrite separates pearlite from austenite at the growing interface (i,e., the advancing face of Fe3C is in contact with ferrite, not austenite) and the ratio of the thickness of this layer to the spacing of the pearlite has not been found to vary with alloy content or transformation temperature. This observation does not require any alteration in the above equation: however, it may require that a different significance be attached to the factor, AT. The AT term appears in Eq. [I] as a consequence of a factor for the amount of growth per complex transformed at the interface.* It is based *This is not the sole reason for expecting such a relationship. See Ref. 7._______________________________________________________ on a l/2 ?T dependence of the interlamellar spacing. Zener2 has developed a theory which leads to Soa 1/?V where So = the pearlite interlamellar spacing. This relation is as consistent with the data on interlamellar spacing as other relationships, although, as pointed out by Mehl and Hagel,1 the data are not sufficiently precise to consider the relationship as confirmed. The work of Darken, Fisher, and Galligan8 requires that the above be written where f = the thickness of ferrite layer between austenite and pearlite. The present paper is concerned with iron-carbon-manganese eutectoid alloys and reports experimental measurements of the following kinds: 1) the effect of

Jan 1, 1961

By H. P. Leighly, F. C. Perkins

THERE have been several statements in the literature about the difficulty of producing single crystals of high-purity (99.99pct) by the strain-anneal method. Consequently, investigators tend to employ low-purity aluminum for their single-crystal experiments, or else resort to the Bridgman or other techniques which depend on solidification for the production of single crystals. The following paragraphs describe a solid-state method for the manufacture of single crystals of high-purity aluminum which should provide crystals with greater perfection than those formed by solidification. The starting material for this method of producing single crystals was secured from the Aluminum Corp. of America and has a purity of 99.99 pct, the balance being trace amounts of impurities. Specimens approximately 1 by 4 in. are sheared from sheet having a nominal 0.050 in. thickness. The specimens are given a preliminary anneal at 640°C for approximately 3 hr in order to remove fabrication strains and to produce an average grain size of about 1/4-in. diam. The specimens are then etched in Tucker's etchant (45 pct HC1, 15 pct HNO3, 15 pct HF and 25 pct H2O) to remove the oxide film. Critical strain is applied by wrapping each specimen about a 1 3/4 in. round and subsequently straightening it against a flat surface. The high-purity aluminum sheet is sufficiently soft that this operation can be accomplished by ordinary finger pressure. The specimens are immediately annealed again at 640°C for 3 hr and reetched for examination. Ordinarily, considerable growth of certain of the grains will have occurred, and occasionally a single crystal will be produced on the first attempt. The procedure of alternately straining, annealing and etching is repeated until the majority of a batch of specimens contains usable crystal sizes. Typical examples are illustrated in Fig. 1. The greatest changes in crystal sizes are produced in the initial treatments. As the average crystal sizes get coarser in the later treatments, the sever- ity of the strain must be increased in order to produce grain boundary- migration. This increase in severity is effected by decreasing the diameter of the round used for straining (to 1 1/2 in., for example) and/or wrapping the specimens about the round twice, with opposite faces in contact with the round, before flattening. Usually the strain treatments described are not severe enough to produce nucleation in coarse grain high-purity aluminum. The growth of grains occurs by strain-induced grain-boundary migration. It has been observed that the grain boundaries move most readily during the first hour or so of each annealing treatment and that the rate of movement decreases with extended holding times at temperature. Prolonged annealing treatments are therefore not usually beneficial. Similarly, the rate of growth of each crystal appears to depend upon the orientation of the crystal with relation to those of its neighbors. Frequently island grains are formed after the initial heat treatment as the result of slow grain-boundary migration. These sometime become stationary during later heat treatments. Twin orientation interfaces are frequently developed during annealing. These imperfections can usually be removed by increasing the severity of strain to produce actual nucleation of new grains of more favorable orientation at the imperfection interfaces. The largest single crystals produced in our laboratory by the above method measured 4 by 1 by 0.050 in. Examination of Laue back-reflection patterns from a limited area of the specimens, gave no evidence of polygonization. Probably there is some indication of polygonization in the original grain area provided a more sensitive technique is used for detection. Experiments to produce wider specimens were less successful, possibly because wider sheets increase the complexity of the strains induced by deformation and promote widespread nucleation. Grain boundary migration occurs preferentially in a direction parallel to the longitudinal axis of the specimen. The choice of specimen geometry with respect to the rolling direction of the sheet appears to be immaterial in regard to the production of single crystals.

Jan 1, 1961

[59H1-Water Law and Its Significance to the Mining Industry by Wells A Hutchins 59H2-Relation of Land Subsidence to Groundwater Withdrawals in the Upper Gulf Coast Region, Texas by Leonard A Wood and A G Winslow 59F3-Hydraulic Mining of Gilsonite and Its Application to Coal Mining by J H Baker 59H4-Recovery of Phosphates by In Situ Fluid Mining by Sylvain J Pirson 59F5-Coal Cleaning Plant Design for Minimum Operating Labor by Wm M Bertholf and John D Price 59F6-Coke Combustibility A Neglected Characteristic by J D Price 59B7-Union Carbide's Uranium Operation at Maybell, Colorado by K W Lentz and F T Temple 59H8-A Rapid Method for Estimating Alumina in Feldspathic Sands by Hugh H Bein 59H9-Water Laws as Related to Dredging in Idaho by Robert A Lothrop, Richard B Porter, and Robert P Porter 58B19-Separation and Washing of Alumina Process Residue by Morton Handelman 59B11-Feed Preparation and Froth Modification for Fatty Acid Flotation by Carl C Martin and Burt C Mariacher 59B12-Design Requirements for Tailing Disposal in the Southwest by E Vern Given 59B13-Semi-Dome Shaped Buildings for Bulk Storage by Edward E Ives and William L Payne]

Jan 1, 1961

By D. W. Lillie

Property changes produced by irradiation of Al-0.4 wt pet Li alloys at 270°C to a burnup of 0.155 pct of all atoms are described. Metallographic evidence of the formation of internal pores and the concentration of gases at grain boundaries is shown. Some conclusions are drawn concerning desirable property characteristics for resistance to radiation swelling. RADIATION induced gases are of great practical significance in nuclear engineering since they affect the behavior of fissionable fuels and control rod materials. In fuels the gases xenon and krypton are the major offenders, producing serious em-brittlement at low irradiation temperatures and gross swelling at high irradiation temperatures. In control rod materials containing boron, the production of helium from the B 10 (n, 0) Li7 reaction produces similar reactions. Since the trend in reactor design is for operation at increasingly high temperatures, the phenomenon of high-temperature swelling by these induced gases has been the subject of considerable recent study. The objectives of such work have been to obtain engineering information and quantitative data on the effects in specific fuels and control rods and to obtain further understanding of the mechanism of gas damage so that more intelligent corrective steps can be made. Analogue systems are often useful for the latter objective and in this case alloys containing Li are suitable in view of the reaction Li6 + n - He4 + He 4. Both products are gases and no serious radiation problem is produced to complicate post irradiation handling. Considerable caution is, of course, necessary in any operations in which tritium release is possible. The present program was initiated to provide a detailed study of the effects of He + H3 generated by irradiation in Li-bearing alloys. The results on Mg-Li solid solution alloys have been reported elsewhere.' This paper presents information on irradiation of an A1-0.4 pct Li alloy in which the lithium was present as highly enriched Li6 in order to maximize the radiation burnup. PROCEDURE The original intent in the selection of the alloy content was to have Li in solid solution at all temperatures. It became apparent, however, that the solubility of Li in A1 was substantially lower than that reported in the original reference consulted.' This was substantiated by the work of Nowak3 who reported solubility of less than 0.01 pct Li at 100°C. The alloy used (0.4 pct Li) was therefore two phase at room temperature. The irradiation temperature was estimated to be about 270° C, and at that temperature all or almost all of the Li would be soluble under equilibrium conditions. The precise state of the alloy under irradiation is not known. Aluminum used was 99.996 pct purity (max. impurities Si 0.002 pct, Mg 0.001 pct, Fe 0.0005 pct, and Cu 0.0005 pct). The lithium was obtained from Oak Ridge National Laboratory; 96.1 + 0.1 pct of the lithium was ~i~, but chemical impurities were 0.25 pct Ca, 0.05 pct Fe, 0.02 pct Na, 0.02 pct Cu, 0.01 pct Sr, and 0.01 pct Ba. The two metals were melted in an alumina crucible in a resistance heated furnace in an atmosphere of helium. A l-in. ingot was cast in an iron mold, machined to %-in. round, hot swaged (350°C) to 0.080-in. round, cold swaged to 0.060-in. round, and finally cold drawn to 0.040-in. round. Four-inch wire lengths were then cut and annealed at 250°C for 4 hr in helium. Irradiations were carried out in a VT hole in the Argonne CP-5 reactor. The wires were held in an aluminum jig, sixteen wires per capsule, and were maintained in a helium atmosphere for maximum heat transfer. Eight wires of pure aluminum and eight of Al-Li alloy were placed in each capsule. Argome Laboratory statements were accepted as establishing flux and exposure levels. These were based on previous experience and flux map-

Jan 1, 1961

By M. H. Cullender

THE determination of the flow characteristics of gas wells depends upon the analysis of pressure data obtained under shut-in conditions and under one or more known flow conditions. These data are commonly referred to as back-pres-sure test data, and I know you are all familiar with the back-pressure equation where, Q rate of flow, Mcfd @ standard conditions C coefficient of the back-pres-sure curve P 1 formation pressure, psia P • sand face flowing pressure, psia P2 (psia)2/1000 n exponent of the back-pres-sure curve Figure 1 is a graphical presentation of the back-pressure equation; the coefficient is the rate of flow at a difference in squared pressures of 1, in this case 2250 Mcfd, and the exponent defines the manner in which the rate of flow changes with a change in the difference in squared pressures. In Figure 1, the exponent of the back-pressure curve is 0.554 which means that for a 10-fold change in the difference in squared pressures, there will be a 3.58-fold (10 raised to the 0.554 power) change in the rate of flow.

Jan 1, 1961