Search Documents

By Ira Sohn

This article revisits global projections made in 1981of eight metallic and fertilizer minerals for the year 2000. The objectives here are to quantify the differences between the projected and observed levels of consumption for the year 2000 for eight of the 26 nonfuel minerals covered in the earlier study. An attempt is then made to attribute these (often) large differences to the major determinants of minerals demand — income, technological, regulatory and other policy changes, and changes in the recycling rates of the metallic minerals. The eight minerals covered are aluminum, copper, iron, mercury, nickel, phosphate rock, potash and tin. This summary article presents the actual population, gross domestic product (GDP) and per capita GDP changes from 1970 to 2000, compared with the projected rates for these important determinants of mineral use, along with the observed growth rates of minerals consumption for the eight nonfuel minerals included in this study. When the projections are compared with the observed global consumption levels for the year 2000, the differences range from +43 percent for nickel to +229 percent for potash.

Jan 1, 2005

Stellite-6 coatings were formulated on two Ni-base superalloys, namely Superni 75 and Superni 600, by a shrouded plasma-spray process, and the oxidation behaviour of these coatings has been investigated in air and in an aggressive environment of Na2SO4- 60%V2O5. Accelerated oxidation tests were conducted in a silicon-carbide tube furnace under cyclic conditions at an elevated temperature of 900°C for 50 cycles. Each cycle consisted of 1 h heating and 20 min cooling in air. A thermogravimetric technique was used to approximate the oxidation kinetics. The corrosion scales were characterised by XRD, SEM/EDAX and EPMA analysis. It has been observed that the coatings nearly followed the parabolic rate law of oxidation. Overall weight gain conceived in air was just 51% of that in the aggressive environment in the case of coated Superni 75, whereas in case of coated Superni 600, the cumulative weight gain in air was found to be one-third of that in the Na2SO4-60% V2O5 atmosphere. Furthermore, the coating showed very good adherence to both of the substrates during the course of air oxidation, whereas some superficial cracks were observed near the edges of the specimens during the molten salt induced oxidation. XRD analysis revealed the presence of phase-like CoO, CoCr2O4 and Cr2O3 in the oxide scales, which are reported be protective against high-temperature oxidation. The XRD results were further supported by SEM/EDAX and EPMA.

Jan 1, 2005

By William G. Szymczak

A set of experiments were conducted at the Aberdeen Proving Grounds [1] in which explosive charges were buried in saturated sand beneath a suspended rigid platform. The goal of these experiments was to measure the dependence of the impulse transmitted to the platform on the standoff distance and the charge burial depth. Simulations of these experiments were performed using the BUB2D axi-symmetric code using a frictional-cohesive visco-plastic model to describe the response of the saturated sand. This code solves a constrained set of conservation laws in which the liquid region (in this case saturated sand) is assumed incompressible. The explosion is initialized as a high pressure gas bubble (void) within the fluid. Comparisons of the simulations to the experiments are presented together with a study of the physical phenomenology associated with the loading process. In particular, it is shown that the force imparted to the platform is a combination of the impact of the sand on top of the explosion gas bubble and the pressure of the bubble as it expands before venting into the atmosphere. Under certain conditions, when the platform standoff is sufficiently small and the platform is sufficiently large, the bubble can over-expand before venting and pull the platform downward. This phenomenon was studied further through carefully measured and photographed small-scale experiments performed at the University of Maryland [2]. The small-scale experiments provide additional important validation benchmarks for our model.

Jan 1, 2005

By D. Berkley

Off-gas systems often become the limiting factor in production increase and environmental projects. Any upgrade or new off-gas project needs to address control instability issues, instabilities that can result in safety hazards, significant loss of system capacity and/or emissions to the environment [1]. In addition, the design engineer must optimize system configuration and equipment size for the new operating conditions, to have a technically feasible and economically viable project. Dynamic simulations can be used for addressing both the control stability and the design optimization issues. This paper illustrates how the dynamic simulation of transient processes and of their control system can be used in "real life" situations for these purposes, presenting the example of an electric furnace off-gas system design.

Jan 1, 2005

Times are changing for the mining industry. Civil society is demanding that miners pay more attention to the ways they impact on, and engage with, communities around their mines. Miners, in turn, are being forced to adapt and learn new social skills for which they were not originally trained. They are doing so in the middle of a broad resources boom, which is adding short-term operating challenges at the same time as miners need to be developing thoughtful solutions to longer term community issues. This paper examines a number of the issues that now loom on the horizon of mining companies. These include: human resources challenges and the crisis in minerals education; continuing community and social expectations of the resources industry and the impacts they will have, for example, on product stewardship, greenhouse gas emissions and the use of increasingly precious water resources; and current impediments to mineral exploration spending.It is concluded that the greatest challenge for the minerals industry is to develop a stronger cadre of local leaders and for the larger global miners to empower their local management to take on stronger public leadership responsibilities. There is a need for executive leadership to remember both the longer term and shorter term cyclical nature of the mining industry in developing solutions to community problems. Above all there is a compelling case for mining industry leaders to be more actively engaged with the wider community in the resolution of these issues.

Jan 1, 2005

By M. Drozd, A. Ibrado, P. Butcher

While effective in treating refractory sulfide ores, pressure oxidation leaves carbonaceous matter unscathed and able to adsorb gold from cyanide solutions. Barrick Goldstrike's strategy to mitigate this problem is to minimize contact between dissolved gold and native carbon in advance of the carbon-in-leach (CIL) process. Measures currently in use include limiting carbonaceous matter in the plant feed by meticulous blending of ore, controlling the degree of oxidation in the autoclaves and blinding native carbon surfaces with lauryl sulfate. The presence of residual cyanide and thiocyanate in the process water remains to be a cause of premature gold dissolution and loss of gold by adsorption on carbonaceous matter. This cyanide is introduced by water that is recycled from the tailing pond. Of several treatment options considered, oxidation by peroxymonosulfuric acid, also known as Caro's acid, is deemed to be the most effective. Laboratory and pilot plant tests show that Caro's acid can oxidize free cyanide, weak¬acid-dissociable (WAD) cyanide and thiocyanate, resulting in significant improvements in gold recovery downstream. The process requires Caro's acid at 125 % of the stoichiometric requirement and pH in the range of 9.5 to 10 to accomplish the desired destruction in about twenty minutes. A cyanide destruction plant is currently being designed and construction should be completed by the end of 2005.

Jan 1, 2005

By Sudip Basack

"The topic of pile foundation subjected to lateral cyclic load is an age-old problem confronted by Geotechnical Engineers. The environment prevalent in ocean and shorelines necessitates the piles supporting offshore and onshore structures to be designed accounting for the lateral cyclic loading resulting from the effects of sea waves. The quasi-static nature of this type of loading induces remarkable deterioration in the interactive performance of the soil-pile system. This can be manifested as progressive loss in pile capacity associated with increased pile head deflection. The work reported herein is aimed towards conducting rigorous theoretical analysis using finite difference technique so as to analyze the lateral cyclic loading response of a single, vertical pile embedded in cohesionless soil. The theoretical results are compared with the experimental results and reasonably good agreement is noted. This paper presents a brief description of the theoretical analysis carried out with some typical results and the relevant conclusions drawn therefrom. 1. INTRODUCTIONOffshore structures, namely, quay & harbour structures, jetties, tension leg platforms, oil drilling platforms, etc. are largely supported on pile foundations. Apart from usual loads from superstructures, these piles are subjected to continuous action of wave loading. This type of lateral loading is quasi-static cyclic in nature which results in considerable degradation in the interactive performance of the pile-soil system initiating progressive reduction in pile capacity associated with increased pile-soil stiffness. This may ultimately lead to disastrous consequences.Amongst limited research works in this field, the major contributions are made by Matlock (1970), Idriss et al (1978), Poulos (1982), Vucetic et al (1988), Long & Venneste (1994) and Basack (1999). A brief review of these works indicates that the degradation of the pile-soil system under lateral cyclic loading mainly depends upon the following parameters: number of cycles, frequency (cycles per unit time), cyclic load level (ratio of cyclic load amplitude to the lateral static ultimate pile capacity, in case of loadcontrolled mode) and cyclic displacement level (ratio of cyclic displacement amplitude applied at the pile head to the external pile diameter, in case of displacement-controlled mode). As pointed out by Poulos (1981 & 1982), the degradation is mainly due to: 1) partial to zero dissipation of excess pore water pressure generated during cyclic loading in progress, 2) destruction of interparticle bond with particle realignment and 3) rearrangement and gradual accumulation of permanent plastic deformation around pile"

Jan 1, 2005

By Petrus Christiaan Pistorius, Makunga Daudet Seke

The flotation response of a Pb-Zn sulphide ore from the Rosh Pinah Mine (Namibia) was studied in the presence of inorganic depressants such as sodium cyanide and zinc sulphate. Poor flotation selective was observed in the rougher concentrate of the galena circuit despite the use of excessive amount of sodium cyanide. Batch flotation tests have shown that the use of cyanide alone is not efficient for the depression of sphalerite from the Rosh Pinah ore when milling is carried out according to the current plant particle size distribution. The use of both cyanide and zinc sulphate improved the selectivity between galena and sphalerite much better than cyanide alone. Flotation selectivity is limited by the mineralogical texture of the Rosh Pinah ore sample. Microscopic analysis has shown that the presence of sphalerite in the galena concentrate is also due to poor liberation between galena and sphalerite, especially in the middlings. Hence selectivity could be improved by regrinding the rougher concentrate prior to the cleaning stage. Keywords- Sulphide ores, Flotation, Flotation depressant, Mineralogy.

Jan 1, 2005

By E N. Sparg, O D. A Deuchar, F Needham

Decline shafts are an attractive option to both new and existing mining operations where there is a need to access an inclined orebody deposit via on-reef development so as to generate a return in the shortest possible time. There are many different technologies that are available to transport men, material and rock in incline shafts. This paper focuses on the applicability of two hoisting technologies for decline shafts, namely endless and direct rope systems. The pros and cons of each system are reviewed. A common concern with direct rope haulage systems is the possibility of generating slack rope during deceleration. This paper illustrates the issues involved in designing a system so as to avoid the possibility of slack rope. In conclusion, the key factors relevant to the selection of endless or direct rope haulages for a particular decline application are reviewed. The paper is a joint submission by FFE Minerals-Vecor and Qualter Hall UK.

Jan 1, 2005

By D. Mu

A method is presented for evaluating the effective gas diffusion coefficient of porous media. A series of random-distributed porous solids with different porosity are generated, a solution of the gas diffusion equations inside the porous media is obtained using the finite element method (FEM), and then the effective gas diffusivities are computed. The results show that there is a percolation threshold sp, and this percolation threshold decreases with an increase in the connectivity of the pore network; the relationship between the effective diffusivity and the porosity is strongly nonlinear when the porosity £ is less than about 0.2; and is quasi linear for higher porosities. The threshold decreases with increasing the connectivity of the pore network. A formula relating the effective diffusion coefficient with porosity is proposed.

Jan 1, 2005

By E Mielczarski

Determination of the adsorbed layer composition and structure at molecular and atomic levels and understanding adsorption mechanisms and dynamics are vitally important for the preparation of surface layers with specific functions. Direct information, at a molecular level, about mineral surface composition, its structure and surface distribution is crucial to perform an efficient separation process for mineral beneficiation. This information is equally important for modifying surface properties of industrial minerals for specific applications such as: fillers, composites, weathering resistance, etc. An understanding of the mechanisms and kinetics of the interaction of first adsorbed organic molecules with mineral surfaces is a fundamental requirement for the prediction and control of the macroscopic surface properties governing the efficiency of separation technologies or new material formulations. The developed infrared external reflection technique has a unique ability to study interface phenomena, at a molecular level, on heterogeneous substrates. The variety, precision and reliability of information about the interface phenomena delivered by this technique is superior to any other single technique. The experiments are fast and non-destructive. High sensitivity (starting from 20 per cent of the monolayer) in situ collected information in a multiphase system, even in the region of strong absorption of the substrate, makes this technique a very valuable experimental tool. The complexity of the recorded reflection spectra, their sensitivity to variations of the optical properties of all bulk and surface components and their spatial distribution in the system under investigation, are in fact the major strengths of this technique. A few examples of the application of this multi-diagnostic technique, for monitoring surface modifications of semi-soluble minerals for selective flotation, will be discussed in detail in this paper.

Jan 1, 2005

By F. Barriga-Ordonez, J. A. Finch, L. Calzado, S. R. (Ram) Rao

Sludge, formed by lime treatment of acidic drainage and stored in tailing ponds of the Sudbury region, contains 5-7% Ni, mostly in a mix of hydroxides with Fe (~ 10%), Mg (~ 10%) and Cu (-0.5%), and Ca (-3.5%) as sulphate. Investigations were conducted to recover nickel by a 2-stage process. In the first stage, the sludge was leached with sulphuric acid at pH 3.2. About 90% of the nickel was extracted, producing a solution, which contained mainly nickel (2 g/L) and magnesium (3.7 g/L). In the second stage, nickel was separated by treating with ozone which recovered 99% of the nickel in the Ni(III) oxidation state as -85% pure nickel oxide-hydroxide (NiOOH) precipitate. The oxide settled and filtered readily. A potential use of the product in battery making is suggested. The leach residue contained 0.5% Ni making it less toxic for disposal. Some physical properties of nickel oxy-hydroxide and process parameters including ozone consumption will be discussed.

Jan 1, 2005

By A Nisbett

The largest single operating loss in many hydrometallurgical plants is the poor recovery of leached product in the solids sent to tailings. Any reduction in the concentration of the valuable species in this stream will improve the project economics. Conventional design, to reduce the soluble loss, is to increase the number of wash stages or the wash/water ratio. This approach is limited in effectiveness as it can only reduce the soluble loss to that dictated by the concentration in the returning solution. For copper plants this concentration is set by the recovery in the solvent extraction (SX) plant. When using a single grade of SX feed a single grade of SX raffinate is produced generally with five to seven per cent of the copper still remaining in solution. An alternative approach has been developed by Cognis Corporation and implemented on a number of recent projects using engineering input from Miller Metallurgical Services. The SX plant feed is æsplitÆ into two different streams: a high-grade stream containing up to 75 per cent of the copper and a low-grade stream with the remaining copper. This Split-CircuitÖ concept has significant benefits in terms of both copper recovery and reduction in acid costs. The high-grade stream has the bulk of the copper removed and the raffinate sent directly back to the leach; to fully re-use the acid that has been generated during extraction in the SX process. The recycling of this higher concentrated acid stream considerably reduces the acid in the raffinate sent to washing steps. It represents a significant saving in acid consumed via the tails stream. The low-grade stream has a significantly lower SX feed grade and hence produces a lower raffinate acid and copper concentration. This lowers the economic species in the wash solution and hence reduces the soluble loss accordingly. Other operating improvements are realised with lower neutralisation costs (with the lower acid in the wash stream) and from a decreased need for in-circuit neutralisation to improve SX performance. The SX plant itself is also split into a high-grade extraction and a low-grade extraction stream to enable the low-grade raffinate to be produced. A number of circuit alternatives have been utilised that have provided a range of benefits. The circuit concept has been included into both new and existing plant operation. As a result of this experience other methods of incorporating the concept into a circuit have been developed.

Jan 1, 2005

By Paulo Roberto Pereira

This paper is motivated by the belief that increasing drilling and blasting costs will not necessarily bring about better digging or crushing productivity. As a matter of fact it can be counter productive as the ensuing discussion will show. In the two case studies presented herein when powder factor increased, productivity at a rope shovel and at a primary crusher decreased. Experience has shown that equipment (shovel and primary crusher) productivity increases as the powder factor increases and concurrently operating costs decrease. This is illustrated by Figure 1where the graph shows (assuming drilling costs constant) that for increases in powder factor initially operating costs might fall till a certain point and then they start to go up again. By the same token we need to understand what is the behavior of the operation’s productivity. It seems intuitive productivity goes up for increases in powder factor but when an operation reaches the point of minimum operating cost one could say that productivity reached its maximum. For continuing increases in powder factor can productivity still go up or does it go down? This paper presents two examples where the productivities of a surface coal mine and of a quarry are reduced for increases in powder factor. This indicates that these two operations could be operating to the right of their minimum operating costs and maximum productivity and therefore wasting precious drilling and blasting dollars and resources. Moreover, their productivity is following the red dotted line in Figure 1 and the question becomes can they follow the blue dotted line for increased drilling and blasting costs? The industry owes to itself to determine this minimum operating cost point and what can be done in case that the productivity goes down afterwards despite an increase in drilling and blasting costs. In other words, utilize your drilling and blasting resources correctly. In the two examples that follow single explosive loading strategies make powder factor a valid means of comparing the results of productivity as a function of powder factor. Also, external factors such as equipment operator influence are eliminated due to the long time span considered in the analysis

Jan 1, 2005

By G. P. Gu

The in-service 90/10 cupro-nickel tubes in a water-chiller system suffered from severe corrosion damage during their relatively short service life causing unexpected down time. In addition to downtime, the environmental risk associated with losing refrigerant was also a concern that initiated this investigation, Microstructural investigation using SEM and electron microprobe indicated that pitting corrosion had resulted in local nickel depletion, During the corrosion process, copper appeared to have re-deposited around the corrosion pits accelerating the local corrosion.

Jan 1, 2005

Material sampling theory is well established in mineral process monitoring, improvement and control. It has been much enhanced by fundamental contributions due to Gy. When GyÆs sampling theory is applied to sampling inspection and monitoring, it provides estimates of average quality or extent of contamination. It also provides estimates of uncertainty, but these often ignore uncertainty in estimated variograms or other measures of variability. Risk assessment is often an implied task in sampling inspection and quality monitoring. A valid technique of risk assessment needs to take into account the uncertainty in the variational measures themselves. Standard statistical tolerance limit calculations which do take such uncertainty into account can be adapted to develop a technique for handling uncertainty in variational measures such as the variogram. Data from a published example is used to illustrate the technique.

Jan 1, 2005

With the theme of û æUnderground Ore Handling SystemÆ, Kopanang Mine completed an extensive project on a specific system with technologies for the handling of ore from a dedicated drawpoint to the shaft system. The intended rail haulage tramming system had to be capable of handling the shaft design and Life of Mine (LOM) requirements. Kopanang is an AngloGold Ashanti gold mine situated in the province of the Free State in South Africa. In the Sotho language the name æKopanangÆ means to come together as a team. ItÆs an appropriate name given that 25 companies worked on this project. The future focus at Kopanang is to establish four mining levels between 3 to 4 km south-west of the shaft and two mining levels to the west. The mine has an expected life of almost 20 years and capital was approved in order to access this reserve to establish the infrastructure to handle the ore, hence this exclusive rail haulage tramming system of close to R40 million (SA rands), which took three years to construct. Apart from the fact that this system had to be capable of handling 6500 t per shift at a depth of over 2 km over a length of 3.2 km, some of the major considering factors were: safety, economic factors with improved labour productivity, efficiency and reliability, risk termination, and ergonomics. The system comprises two 20 t locomotives operating in a double header configuration from a dedicated draw point to a dedicated tip area for the reef and waste ore. With the objective of handling high speed and high capacity, this 200 t payload train is capable of running at 35 km/h powered from a 500 volt ac overhead line. Each loco consists of two 90 kW dc motors with ac/dc power conversion on the locomotive. For the system to operate at this speed, the rail system is constructed with Class 1 rails over the entire hauling distance. The tipping mechanism is unique and the span of 11 hoppers each with a load of close to 20 t is capable of tipping the pay load of 200 t in about 20 seconds hands free.

Jan 1, 2005

By Allison

During the 1980’s, laboratories opened throughout the United States to serve the analysis needs of a rapidly growing asbestos abatement industry. The samples analyzed were either collected during the abatement of known asbestos-containing materials or were suspect asbestos-containing construction materials. Many asbestos analysts received minimal training and used analytical protocols that were industry specific. False positives (reporting a sample as containing asbestos when none is present) went unnoticed or had minor repercussions. The mindset of the industry was to err on the conservative side – it would be better to identify a non-asbestos fiber as asbestos than visa versa. With growing public awareness of the health hazards of asbestos, other materials began to be tested for asbestos content. Rock and ores began to be tested for naturally occurring asbestos by these laboratories using the same protocols or an in-house protocol. Analysts were given no additional training and accreditation, in most cases, it was not required. With no consistency in sample collection, testing protocol or expertise in analysis, significant discrepancies in final results can be expected. If we further complicate this scenario with misidentification of naturally occurring look-a-likes for asbestos, expensive false positives are likely. To avoid the repercussions of misidentification of naturally occurring chrysotile asbestos from look-a-like fibers in rock and ores, correct sampling and analysis protocols with more stringent scientific diagnostic criteria are needed.

Jan 1, 2005

By E. Dernedde

Industrial plants located in the province of Quebec, Canada, are subjected to large variations of the ambient air temperature, Building ventilation systems of these plants must have some flexibility in order to meet industrial hygiene standards (TLV for chemical substances, heat stress and cold stress) at any time of the year, The building ventilation of a bath treatment plant of an aluminium smelter in Quebec was examined under summer and winter conditions, Part of the plant has periodic emissions of hydrogen fluoride gas and heat from hot anode butts, CFD modeling was used to optimise the building ventilation of the bath treatment plant, The present study proposes a modified building ventilation system, which improves the internal environment, complies with industrial hygiene standards and also reduces heating costs by 20 % during winter.

Jan 1, 2005

By I Jabouri

There are many physical factors that can affect the self-heating rate of coal. The presence of seam gas has often been referred to as inhibiting coal self-heating due to the limited access of oxidation sites created by the presence of the gas adsorbed on the coal pores. Similarly, the presence of bed moisture in the coal also acts as an inhibitor of oxidation by blocking access of air into the pores. Gas drainage of a coal seam prior to mining removes both gas and moisture from the seam. Bulk coal self-heating tests in a two-metre column on both gassy, as-mined and gas-drained, dried high volatile bituminous coal show that removal of gas and moisture from the coal accelerates the rate of self-heating to thermal runaway from 8.5 days to 4.25 days, from a start temperature of 30¦C, with an airflow of 0.25 L/min. The corresponding gas evolution pattern for each of these situations is different. Therefore, it is necessary to take this change in coal condition into consideration when developing a spontaneous combustion management plan.

Jan 1, 2005