Search Documents

By Ulrich Langosch

In the 1990s the German mining industry introduced a new generation of shield supports. The new design of support has a maximum load capacity of 10,000 kN, making these units as strong as the shields used in Australia and in the USA. DMT took more than 3,100 underground observations in order to verify the roof fall frequency by statistical analysis. The results of this work have led to practical recommendations for roof control and the required shield support system on longwall faces. The underground observations have been correlated to Rock Mass Classification, to stress calculations and to the angle between the direction of the fissures and the direction of longwall mining_ The analysis work yielded the following two sets of results: 1. There is a critical distance between the canopy tip and the coal face (Tip to Face TF,n,). The TF,n, is predictable and relates to: the thickness of the first roof layer and its uniaxial compressive strength. The face support should have a TF that is less than the TFcrtt in every underground longwall situation. Exceeding the TF crit call immediately result in a roof fall. 2. Using the obtained regression equation DMT is able to calculate the probability of the roof fall frequency (FF), which describes the roof fall sensitivity. When TFcr;, is exceeded the predicted roof fall FF relates to: the measured support resistance (MSR) of the shield support the calculated vertical stress (p?) the fissure-direction index (DI = angle between main fissure direction and direction of mining) and the distance by which TFcrit is exceeded (ATF). Armed with these results DMT is now able to predict the critical distance between the tip of the canopy and the coal face (TFcrit), as well as the roof fall frequency, for all shield designs. By applying the new calculation method it is now possible to compare alternative longwall layouts and different shield support types under pre-set geological conditions. Mining engineers on site are therefore in a position to make the necessary roof control preparations required to run the longwall operation to maximum efficiency. The results provide a useful basis for making practical recommendations and for selecting the most effective design of shield support. The paper uses practical examples to demonstrate the R&D results and present the various methods now available for calculation and prediction in longwall roof control.

Jan 1, 2003

By Fred N. Kissell

This handbook describes effective methods for the control of mineral dusts in mines and tunnels. It assumes the reader is familiar with mining. The first chapter deals solely with dust control methods, regardless of the application. It is a brief tutorial on mining dust control and will be of help to the reader whose dust control problem does not conveniently fit any of the mining equipment niches described in later chapters. The subsequent chapters describe dust control methods for different kinds of mines and mining equipment. This includes underground coal and hard-rock mines, as well as surface mines, stone mines, and hard-rock tunnels. Because dust sampling has so many pitfalls, a chapter on methods used to sample dust is included. For those occasions when there is no practical engineering control, a chapter on respirators is also included. Except for those listed as ?future possibilities? in the longwall chapter, the dust control methods described are practical and cost-effective for most mine operators. If controlling dust were a simple matter, dust problems in tunnels and mines would have been eradicated years ago. Unfortunately, most underground dust control methods yield only 25% to 50% reductions in respirable-sized dust. Often, 25% to 50% reductions are not enough to achieve compliance with dust standards. Thus, mine operators must use several methods simultaneously, usually without knowing for sure how well any individual method is working. In fact, given a 25% error in dust sampling and day-to-day variations in dust generation of 50% or more, certainty about which control methods are most effective can be wanting. Nevertheless, over the years, some consensus has emerged on the best dust control practices. This handbook summarizes those practices.

Jan 1, 2003

The inherent weakness of the Zincor and similar iron removal processes is the relatively high undissolved zinc loss associated with the iron residue. High soluble zinc losses also occur due to poor filterability of the iron residue even though it may be limited to intermittent events. This work focussed on defining the optimum operating window for the Zincor iron removal process where iron is mainly removed in the form of amorphous, intermediate iron phases such as schwertmannite and ferrihydrite. In terms of the main operating conditions, optimum filterability was achieved under the following conditions: pH of 3.0, temperature as high as practically possible (70C), at least 25 kg/m3 seeding, and a retention time of at least 4 hours. When increasing the temperature from 60C to 70C, the required residence time decreased by almost 50%. Undissolved zinc loss was also reduced from 8% to between 2% and 3% by using a basic zinc sulphate/zinc oxide mixture as neutralising agent to effect iron removal.

Jan 1, 2003

By Chetan P. Malhotra

This paper describes an online control system and simulation environment for reheating furnaces. The system can be configured for implementing manual control as well as automatic control using either look-up tables or online model predictions. The simulator is also used for offline generation of optimized normal operation and delay setpoints for look-up tables and generating ideal heating curves for model-based control. Finally, it is employed to compare the performance of the above control strategies over a typical period of operation of a pusher-type reheating furnace. Keywords: Reheating furnace, control strategy, model-based control

Jan 1, 2003

By Chang-Young Choi

Korea Zinc commenced zinc production in 1978 with a capacity of 50,000 tpa. Since then, continuous investments have been made and resulted in Korea Zinc now being the biggest zinc and lead producer in the world. In the course of increasing zinc production capacity, the company management realized that the company needed a lead smelter to prevent the solid waste disposal problems by treating the lead containing solid waste. This paper begins by briefly stating the objectives and the roles of the lead smelter at Onsan. It describes the QSL process and the TSL process, and further extends the description of the TSL process, through which harmless inert solid waste could be produced for secure final disposal. It is also mentioned that the TSL process plays an important role in the integration of zinc and lead production. Throughout the paper, a positive attitude in handling the environmental issues in the non-ferrous smelting industry is emphasized. Finally, a solution for the solid waste disposal problem in the zinc and lead industry is proposed, with which the environmental issues can be an opportunity rather than a crisis. The current operation at Onsan suggests the future direction of the non-ferrous smelting technology that all of the zinc and lead producers should pursue.

Jan 1, 2003

By I Doye

Acid mine drainage is a serious environmental problem caused by the oxidation of sulfide minerals responsible for highly acidic, sulfate and metals-rich drainage. Several methods of mine waste management have been developed that reduce liabilities on environment. Layered co-mingling of waste rock with compacted tailings, covers with capillary barriers effect, and co-disposal of waste rock and tailings are these new methods which are used to reduce the formation of acid mine drainage. These methods shield waste rock dumps from oxygen. These techniques could prevent oxidation reaction. In this study, alkaline industrial wastes are used with acid generating tailings to inhibit acid mine drainage. The alkaline wastes selected are cement kiln dust (CKD) and red mud bauxite (RMB). These alkaline materials are used to keep neutral conditions in the fine material layer and to inhibit the metabolic activity of Thiobacillus ferroxidans which catalyses the oxidation of sulfide minerals. A series of timed static leaching tests were performed by reacting samples of mine tailings with two, five and ten per cent alkaline material in order to characterise geochemical balance between liquid and solid phases. Column tests have been set up with oxidised tailings, waste rock, CKD, and RMB. Column tests have been carried out to simulate layered co-mingling, covers, liners, and co-disposal of waste rock and tailings. Column leach tests were conducted in order to investigate the long-term neutralisation potential of alkaline materials and the drainage water quality. Bacteria counting were performed on each sample after testing. The results obtained show that the addition of alkaline materials permit the retention of near neutral conditions in the fine material layer, thus increasing water quality and preventing bacteria development. In fact, the pH results show that the use of five per cent, ten per cent CKD or ten per cent of a mixture of CKD and RMB permit the retention of neutral pH conditions in the reactive layer. At these percent rates, the concentrations of Al, Fe, Cu, Zn, and SO4 in solution are significantly reduced compared to those obtained with the tailings only. In presence of waste rock, the relative position of the fine material layer is important. When the fine material layer overlaying reactive waste rock is composted of reactive tailings with ten per cent CKD and ten per cent (CKD:RMB), a delay was observed before achievement of near neutral pH. The neutral pH conditions remain stable over time. The mixture of CKD and RMB provides a better short-term neutralisation than the use of CKD alone. The use of alkaline materials is beneficial in order to reduce the concentrations of Fe and other metals such as Cu and Zn as well as the number of viable bacteria. The use of ten per cent RMB alone does not involve the neutralisation of reactive tailings. In the cases where the fine-grained layer are below or mixed with the waste rocks, the near neutral pH values are directly reached with ten per cent CKD. However, the pH values decrease rapidly and the number of viable bacteria increases.

Jan 1, 2003

By Karl J. C. Harries

"11.1. INTRODUCTIONA royalty is the most common form of interest retained by an owner who is disposing of his property or by a joint venturer who ceases, voluntarily or otherwise, to participate in the joint venture.1 Rarely does a non-participating party have a direct interest in the property and/or assets of a project, except during the period when a non-participating joint venturer may be having his interest diluted.2 In fact, it is most unwise to permit a non-participating party to have such an interest. It may give rise to significant problems that could prevent or substantially delay the development of an orebody and require a considerable amount of time, effort, and money to correct.3In negotiating a royalty, it is important to be aware that there is no law or convention that says, “You just don’t do that in a royalty agreement.” As with any agreement, inventiveness and flexibility on the part of the negotiator are not just assets, but virtual necessities. It is also for this reason that it is essential to read the royalty provisions, particularly the definitions, fully and carefully, especially if you are the recipient. On the other hand, if your inventiveness and flexibility cause your accountant to question the advisability of one of your ideas, pay close attention to him.4 He will, no doubt, have had experience with many royalties, and no competent professional adviser disparages a client’s ideas without good reason. Besides, he will probably be the person who will be determining the royalty or certifying the determination of it. At the very least, he will be auditing your general financial statements, which must, of course, reflect the royalty determination. Heeding his advice not only may make the determination easier but also will probably save you money in professional fees later on. Nevertheless, do not simply accept his comments or recommendations without understanding what they mean, why they have been made with respect to your royalty agreement (sometimes professionals have comments that they make as a matter of course and, even though they may be valid, you should require them to be justified to you), and how they will affect your royalty determination.It is surprising how many corporate payors insist that their standard royalty provisions5 be used as a matter of policy, thereby effectively tying the negotiator’s hands. It is even more surprising, and to professional advisers frightening, how many of the senior employees who insist that such a policy be adhered to, virtually without variation, do not know what is in the standard provisions and would be hard-pressed to explain them to a property owner. If standard provisions are appropriate, by all means use them, but do allow experienced and sensible negotiators some flexibility and make sure that everyone within the corporation who may have to use such provisions – negotiator and supervisor alike – knows what they contain and why they are as they are. For example, there are often good and convincing reasons to describe a deduction in a certain way or to include a certain specific type of deduction. On the other hand, quite often the answer to the question “why?” is that “it has always been there”; this is, or should be, an unacceptable answer. In any event, if you, as the negotiator, appear to know what you are talking about, are familiar and comfortable with your royalty provisions, and are backed up by your boss with the same words or reasoning, a property owner cannot help but be satisfied that you are knowledgeable, even if he still does not agree with your provisions. Finally, if you do use standard provisions, make sure that they are reviewed and updated regularly."

Jan 1, 2003

By Ashton M. Swartbooi, Robert van Hille, Alison E. Lewis

"Nickel production by precipitation using hydrogen reduction generates an ammonium sulphate solution containing approximately 2g/L of nickel, and 1g/L of cobalt as an impurity of the process. Sulphide precipitation is an effective method for heavy metal removal, especially when compared to hydroxide processes: metals can be removed from solution at relatively low pH levels, small quantities of sludge are formed, and due to the high reactivity of sulphides the reactor retention time is reduced. However, the low solubility of sulphide species can lead to spontaneous nucleation of fines (due to higher supersaturation levels which are difficult to separate from solution, leading to reduced process efficiency. Using a fluidised bed reactor, fines formation can be minimised as the pellets provide a large surface area and promote heterogeneous nucleation.A synthetic nickel-cobalt ammonium sulphate solution was reacted with two forms of sulphide reagent: (a) a liquid sulphide solution and (b) gaseous hydrogen sulphide. A range of factors (including pH, reagent concentrations, metal to sulphide molar ratio, flow rates and recirculation rates) influencing the efficiency of the precipitation reaction have been studied. The efficiency of the precipitation reaction was measured using both metal recovery and fines formation as indicators.Figure 1 shows the effect of decreasing the metal:sulphide ratio (at constant SS = 2.725e+17), on the metal removal for liquid sulphide. By decreasing the metal:sulphide ratio, up to 99% removal of both nickel and cobalt could be achieved.These results also indicate that the precipitates that formed were polysulphides, since no sulphide was present in solution after the experiment. This would also indicate that a lower metal:sulphide ratio would be more favourable. However, decreasing this ratio (at constant metal concentrations) would lead to an increase in the fines concentration, because of increased supersaturation levels induced by the higher sulphide concentrations. To decrease the supersaturation, dilute solutions of either reagent would be employed."

Jan 1, 2003

By Yoshihiko Maeda

It is said that the 21st century will be an era of the remedy of the global environment. In order to reserve natural resources for the future and to avoid the dispersion of heavy metals after usage and to avoid pollution problems, it is extremely important to recycle heavy metals as much as possible by reasonable recovery procedures. The nonferrous metal industry is expected to play a important role in the recycling of heavy metals that are originally their products. From the depressed metal price experienced in Japan in 1980'h due to the sudden change in current exchange rate between US dollar and Japanese yen, one of major nonferrous metal company, Dowa Mining, has diversified its business area not only to the so-called down stream, but also to the environmental business including metal recycling, industrial waste treatment and soil remediation by utilizing technologis and facilities once used or still used for mining and smelting of copper, zinc, lead and precious metals. In this paper some of these applications will be presented.

Jan 1, 2003

By Knut L. Sandvik, Erik Larsen

Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. The future silicon feedstock is most likely not reject from the production of electronic-grade silicon. There will probably be a more direct solar-grade silicon route, excluding the electronic-grade silicon "detour". Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this. Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain.

Jan 1, 2003

By E. Berrezueta

Automatic digital phase imaging should yield unbiased and representative characterizations of gold ores. However, this is not a simple tusk due to low gold grade, fine grain size, possible complex mineralogy, nugget effect, etc. Using the same sections of a gold-rich ore, a critical test was performed using an optical microscope (OM) and an electron microscope (EM). In general, the two methods are consistent and useful for ore processing. There are some minor differences, such as the detection of very fine gold grains is enhanced by EM. Key words: Digital imaging, Gold ores, Mineralogy, Electron microscopy, Optical microscopy

Jan 1, 2003

The torsion test is considered as the best test used when the part is subjected to static or dynamic torque. Many published papers have investigated the torsion of non-heat treated metals. However, very few published papers dealt with the torsion behaviour of heat treated metals. The aim of this work was to study the effect of heat treatment on the torsion behaviour of steel alloy (AISI 01), which can be used for manufacturing small and medium drills, taps and reamers. The diameter of specimens used was 15 mm. The metal used was heat treated under different conditions, then torsionally tested. The results of torsion test were divided into two groups: results obtained during elastic limit from which the shear stress, shear strain and modulus of rigidity were calculated, while from the results obtained during plastic limit the plastic depth was calculated by applying derived equation when the angle of twist was more than yield value. The results obtained indicated that the value of hardness alone is not sufficient to establish heat treatment conditions. Rather, it was found that the determination of plastic depth together with hardness can help in the establishing of the optimum condition which was hardening temperature of 820¦C, hardening time 20 minutes and tempering temperature 220¦C. This condition produces hardness of 60 HRc and plastic depth of 2.5 mm.

Jan 1, 2003

By M. N. Brodie

"The ability to adjust the speed of a SAG mill offers benefits to the process and to equipment maintenance. It can be provided with some slight effect on availability ranging from somewhat enhanced to somewhat reduced, depending on the particular equipment that is used. Several techniques have been developed for monitoring the magnitude of the contained charge, and several algorithms have been used to control mill feed rate and mill speed. The various benefits and the means by which they can be realized are examined and compared. Reasons for Variable SpeedProcess RequirementsThe recovery of minerals from ore is dependent on particle size and residence time in process. Separation in a given plant is most efficient at a particular rate and a particular size (e.g., 80% minus 200 mesh). If the particle size increases, less mineral will be liberated. If the particle size is significantly reduced, the process of choice may not be able to effect separation, and power, media, and maintenance costs would be increased.If a SAG mill-ball mill combination delivers the desired throughput at the correct size for efficient separation when processing ore of the design hardness, some adjustment must be made to maintain this condition when the ore changes. The processing of ore softer than design will result in overgrinding, unless:• the throughput is increased inversely to the change in hardness which lowers recovery by overloading the separation facilities;• or the SAG mill feed rate remains constant, but the speed is reduced to feed coarser material to the ball mill for finish grinding to the desired size.There is also the effect of changing milldiameter to consider. A nominal 36 ft diameter SAG mill will have an effective diameter of 35 ft with new liners and 35 ft 6 in. with worn liners. A mill designed to operate at 0.76 p.u. (per unit) of critical speed with new liners (9.84 rpm) will be changed to 0.765 p.u. with worn liners. If 0.76 p.u. is the desired value, the mill speed should be reduced to 9.77 rpm."

Jan 1, 2003

By J. A. Organiscak

This paper examines methods for limiting occupational silica exposures for roof-bolting personnel in underground coal mining. A canopy air curtain and an air tube were evaluated as means to provide filtered air over the breathing zone of these personnel. Laboratory testing showed that dust reductions beneath the air curtain and air tube approached 60% and 40%, respectively, with low interference air velocities. The data also showed that dust reductions were highest for positions closest to the device and that these levels decreased with distance. This paper also evaluates a metal rake, a flexible insert and a rigid insert for cleaning the roof-bolter dust collector box. Less dust was produced when using the rigid insert. Surprisingly, the flexible insert was sometimes no better than scraping or raking the dust onto the mine floor. However, little dust got on the workers coveralls when using either of the inserts.

Jan 1, 2003

By R. Weyhe, B. Friedrich, H. Heegn

"Nickel-metal hydride batteries (Ni-MH) are storers of electrochemical energy, which have a higher specific storage capacity than lead or nickel-cadmium batteries. The demand for Nickel-metal hydride batteries is increasing rapidly since their market launch in the early 1990's. In 1999 the output of cells exceeded 80,000 tons per year (1 billion cells per year). Today there is no suitable and sustainable recycling process to recover nickel, cobalt and rare-earth metals. The discarded batteries are used in the steel industry as alloy material because they contain nickel. Cobalt and rare-earth metals are lost; they are non-recycleable.In a German governmental funded research project, IME Aachen, ACCUREC Mühlheim and UVR-FIA Freiberg are cooperating in processing as well as in creating a feasibility study. The target of this project is the development of a new recycling process for metal recovery from Ni-MH-batteries. The proposed process consists of a combination of mechanical, pyrometallurgical and hydrometallurgical processing steps.After shredding the steel shell, the various fractions of battery materials are carefully separated by mechanical processing. A hammer mill with one rotor with a perforated discharge grid of 20 mm opening, was found to be suitable for crushing the batteries to release the active mass of electrodes for metallurgical processing. The ground material is wet screened at a mesh size of 0.5 mm; thus a fine fraction is obtained with valuable components such as Ni, Co, and RE and an oversized fraction consisting of a mix of iron chips, electrodes grids, plastic chips, paper, and flocculent material of separators. The organic components are avoidable when there is a thermal step at the beginning of processing batteries.The separated fine fraction is smelted in an electric arc furnace. Any pyrometallurgical process relies on a suitable slag system. In this specific case, the process has to allow separation of nickel and cobalt as metal from the rare-earths almost quantitatively, collecting the rare-earths as well as impurities e.g. as oxides. The products are a nickel-cobalt alloy and a slag phase enriched with rare-earth oxides for further treatment to ‘mischmetal’."

Jan 1, 2003

By Chang-Young Choi

Korea Zinc commenced zinc production in 1978 with a capacity of 50,000 tpa. Since then, continuous investments have been made and resulted in Korea Zinc now being the biggest zinc and lead producer in the world. In the course of increasing zinc production capacity, the company management realized that the company needed a lead smelter to prevent the solid waste disposal problems by treating the lead containing solid waste. This paper begins by briefly stating the objectives and the roles of the lead smelter at Onsan. It describes the QSL process and the TSL process, and further extends the description of the TSL process, through which harmless inert solid waste could be produced for secure final disposal. It is also mentioned that the TSL process plays an important role in the integration of zinc and lead production. Throughout the paper, a positive attitude in handling the environmental issues in the non-ferrous smelting industry is emphasized. Finally, a solution for the solid waste disposal problem in the zinc and lead industry is proposed, with which the environmental issues can be an opportunity rather than a crisis. The current operation at Ousan suggests the future direction of the non-ferrous smelting technology that all of the zinc and lead producers should pursue.

Jan 1, 2003

By Y A. Stepanyants, J Crawford

A practical field method for determining the maximum value of the intrinsic oxidation rate, Smax , of sulfidic materials in waste rock dumps is proposed. Knowledge of the intrinsic oxidation rate of sulfidic materials distributed in a dump is necessary for predictive modelling of oxidation and pollutant generation over time. The suggested method uses the fact that drilling waste rock dumps to install probes for monitoring temperature and oxygen concentration causes large volumes of air to be injected into a dump by the drill rig. By measuring the rate of decrease of oxygen concentration along the length of a borehole immediately after installation, it is proposed that Smax can be calculated at different depths. The aims of this work were: to derive a simple, practical formula for the estimation of Smax from the oxygen concentrations measured over time, based on some simplifying assumptions; to use a two-dimensional numerical model that incorporates all the necessary physical processes to model the behaviour of an aerated dump over time for a reasonable range of dump and material parameters; and to compare the results of the two approaches to assess the validity of the simple formula as a method for estimating Smax. It has been found that the technique can provide reliable estimates of Smax when the value is of the order of 10-7 kg(O2) m-3 s-1 or greater. At the lower end of the range however the radius of the zone aerated during drilling becomes an important parameter and further work has been recommended to investigate this aspect of the method.

Jan 1, 2003

By A Ruotsalainen

Mining industry sees a comprehensive future in optimisation and process control. High resource utilisation is a starting platform when lower operational costs with higher rate of return are the target. Simulation is quickly penetrating the mining industry as a planning tool. A discrete event simulation helps to visualise the reality of a mine and the various mining processes, which typically include a fair degree of complexity. What-if scenarios can help to determine the impact of occurring changes to production. Understanding of critical points in the layout and resource allocation at an early stage can help to optimise the material flow. The obtained information may then be used as proposal or confirmation of the system applicability and economy. Simulation is a way to fine-tune and optimise the resources within. It helps to predict system sensitivity to various aspects. Although simulation today is used typically in a feasibility stage, there is an opportunity to continue using simulation for further process enhancement. In the future simulation will without doubt be used increasingly as a dynamic simulation and continuous improvement tool. This paper discusses the use of OptimineÖ simulation tool in resource optimisation. Some examples describe the way the tool operates and how it helps to view the technology, mine layout and operational data.

Jan 1, 2003

By J C. de Vries

When times are tough in the mineral industry û as they have been for some time û typical responses by mining companies are to cut costs and/ or increase production. The latter is seen to spread fixed costs, thereby also reducing unit costs per tonne mined. However, most mineral deposits respond to increased production rates by lowering ore grades, so the reduction in cost per tonne of ore does not necessarily result in a reduced cost per unit of metal produced. The authorsÆ experience is that this process often leads to a mine plan that is a long way from optimal. Producing to the point where marginal cost equals marginal revenue may work well in a manufacturing operation, but it is not necessarily the best strategy for a mining company with a depleting resource. Variations in tonnage and grade with depth, ore reserve optimism and a variety of other factors conspire to produce variations in production rates and grade that often result in suboptimal outcomes and potential mine failure. Added to this is the focus of industry analysts and senior corporate management on such measures as unit costs and ounces in reserves. This is perceived to have the perverse effect of driving the share price down when strategies are adopted that actually improve the value of the mining operation, and vice versa! Many mine failures can be prevented by a close examination of the tonnage grade curve and an understanding of how margins, net cash flows and resulting business risk change with cut-off grades and rates of production. A few relatively simple analyses early in the evaluation of a project can demonstrate the tradeoffs between the main decision parameters, leading to right-sizing of the operation. Once major commitments to major capital items have been made, and reserves have been publicly reported, optimisation of the operation becomes much more difficult than if it had been done earlier. Such investigations can also identify the upside potential and downside risks associated with factors outside the companyÆs control. Many strategies that may enhance value in the good times significantly increase the downside risk in the bad times. What is often called risk analysis typically looks at superficial issues, and does not evaluate the major factors leading to the potential for financial disaster. This paper illustrates some of these major risks, and demonstrates how they may be fully evaluated so that corporate decision makers can make fully informed decisions that take account of the real risks.

Jan 1, 2003

By E. C. Grunsky, B. W. Smee

"The development of low-cost, rapid multielement analytical techniques has generated large geochemical databases in many exploration programs. When a sampling program consists of several thousand samples, the resulting data matrix is enormous and effective interpretation using all of the elements individually becomes burdensome. However, the application of multivariate statistical techniques can extract geochemical patterns related to the underlying geology, weathering, alteration and mineralization. Imaging the results over topography enhances the interpretation of these patterns. Examples of this approach are shown from mineral exploration programs in Canada and Mexico. IntroductionThere has been a dramatic change in the effectiveness of using geochemical survey data in the past ten years. This is mostly due to:• lower cost of geochemical analysis;• lower detection limits;• new methods of multi-element analysis;• a marked decrease in the turnaround time;and• the intelligent use of computers in presenting geochemical data.Geochemical surveys commonly have two objectives: locating abnormal concentrations of ore-forming or pathfinder elements and characterizing the underlying host lithologies. Geochemical surveys often employ a wide range of sample media that may typically include whole rock lithogeochemistry, various soil horizons, till and basal till sampling, stream sediments, lake sediments, and various forms of weathered regolith. Each of these sample media will exhibit a unique element distribution that must be factored in the interpretation phase of a geochemical survey study. This can become a cumbersome process if univariate data handling methods are employed."

Jan 1, 2003