Search Documents

The organisers of this function have suggested that this presentation should accomplish the following broad goals:set the technical tone for the conference to follow, implying some discussion of the æstate-of-the-artÆ of reserve estimation; and raise some current and common problems or deficiencies in our art in order to be thought provoking. As an engineer it is always easier to raise problems than to solve them with state-of-the-art. Consequently, I have had to limit the extensive list of problems that could have been discussed within this presentation. In regard to the state-of-the-art, this presentation will not be an esoteric discussion of the latest statistical estimation processes, although I intend to challenge those with skills in that area to address some of the thought provoking issues later on. The subtitle of the paper was established after reading an excerpt from æLife on the MississippiÆ by the American humorist Mark Twain in which Twain observed that the Mississippi River had become shorter during his working period on the River due to natural cut-offs and man made channels. Projecting into the future, he calculated that by now, Cairo, Missouri and New Orleans, Louisiana would become a single city with one mayor (the two cities are still separated by some 500 air miles). As a moral to this story Mark Twain observed that one can obtain: æwholesale returns of conjecture out of such a trifling investment of factÆ.

Jan 1, 2000

By Yasuhiro Konishi, Yoshiyuki Noda

"This paper describes a new processing of rare-earth oxide precursor, in which rare-earth carbonate powders are precipitated directly from emulsions of rare-earth loaded carboxylate solutions, using CO2 gas and water. This synthetic route of rare earth carbonate is a combined process of the stripping and precipitation stages in a conventional solvent extraction. Using this technique, lanthanum carbonate and yttrium carbonate were prepared at temperatures of 10 to 80°C and CO2 pressures of 0.1 to 3.0 MPa for 120 min. The rates of carbonate precipitation in a batch autoclave were sensitive to processing parameters such as CO2 pressure, temperature, and organic-phase composition. The particle size distributions of the carbonate powders were markedly dependent on temperature and C02 pressure.IntroductionSolvent extraction is the most appropriate commercial technology for separation and purification of rare earths. In typical commercial processes, the rare earths are stripped from loaded solvent extractants using aqueous solutions of mineral acid. After adjusting the pH of the aqueous strip solution, the rare earths are precipitated as insoluble powders of oxalates or carbonates, from which oxides can be produced by calcination. Such conventional processing can be simplified when the stripping and precipitation stages are combined by emulsifying rare-earth loaded solvent extractant with aqueous oxalic acid solution. It is likely that the single-stage precipitation stripping results in a marked decline in the consumed amounts of precipitating and neutralizing agents, thereby saving on both running and capital costs.Yoon and Doyle1) first demonstrated that oxalate powders of lanthanum and yttrium are directly precipitated from rare-earth loaded carboxylic acid solvent extractant when contacted with aqueous oxalic acid solution at ambient temperature and atmospheric pressure. Yttrium oxalate pow4ers were also prepared by precipitation stripping of di-(2 ethylhexyl) phosphoric acid. (D2EHPA) extractant using oxalic acid-hydrochloric acid solutions. 2) Moreover, neodymium oxalates were directly precipitated from organic solutions of tertiary aliphatic monocarboxylic acid and 2-ethylhexyl phosphonic acid mono-2- ethylhexyl ester using aqueous oxalic acid solutions, and powder characteristics of the resulting oxalates were compared with those of powders by the conventional solvent extraction routes. 3 • 4) Recently, attention has been directed towards the influence of processing parameters on the particle size distributions of yttrium oxalate precipitates. 5)"

Jan 1, 2000

By Hani Henein, J. Barry Wiskel

"The easy accessibility and power of the PC, as well as the education of our engineering students in the use of these tools, are compelling reasons for developing computer aided instructional (CAI) tools. There are a wide range of areas in the engineering curriculum where students must learn the steps and the process of applying judgement in problem solving. In the typical course instruction, · an instructor introduces theory to students; the application of the theory to solving problems is often demonstrated in the abstract. Students therefore spend a significant amount of time learning how to apply the theory to problem solving. Additional time and effort must then be spent to get students to the point of learning concepts and integrating this knowledge. A number of computer aided packages have therefore been developed for use in several courses in the materials science and engineering curriculum that encompass both calculational and instructional capabilities. This paper presents an overview of some of these packages which include the solution of a non-linear equation, the instruction of binary diffusion couples, an introduction of crystallography, an introduction to heat transfer and the solution of thermodynamic stability diagrams. The context in which these CAI Tutorials were developed and are being used will be discussed. The pitfalls in the development of these packages will also be discussed. The use of the tutorials has important implications on the expectations from an engineering education of both instructor and student.IntroductionTraditionally, it is quite routine to teach engineering students how to use a computer (the PC today for undergraduates) as a tool in performing engineering calculations or in simulating a process or a unit operation. This often takes the form of one course in computer programming, whether it is Fortran, Visual basic or a spreadsheet, and another course in numerical computation. However, the materials and electronic revolution have brought about considerable advances in computer power and speed, and accessibility. Today, the manipulation of digital images, movies, and speech are commonplace on a desktop PC.' Many mathematical models that were executed only on workstations can now be readily handled on a PC. Concurrently, more of our students own a PC even if their curriculum does not require them to purchase one. Today, virtually every university student has been introduced to the PC in either their elementary or high school education. Hence, the increased capabilities and accessibility of the PC and the familiarity of students with this tool make it compelling to explore its use as an educational tool for our engineering students. This is not a traditional role of a computer in our engineering curriculum."

Jan 1, 2000

By K. R. Robilliard

The Peru based tin mining company, Minsur S.A., commissioned Ausmelt Limited to design, supervise construction and commission a tin smelter and refinery for production of refined tin metal. The plant is located 240km south of Lima, near Pisco, Peru and is operated by Funsur S.A., the wholly owned subsidiary of Minsur S.A.. Selection of the Ausmelt Technology followed a series of crucible scale test work and pilot plant trials conducted at Ausmelt's facility in Dandenong, Australia and two feasibility studies undertaken by Ausmelt in 1991 and 1993. Ausrnelt began the plant design in 1994 with the construction phase following in 1995. Commissioning of the plant commenced early in 1996 with a target throughput of 30,000 tonnes per annum of concentrates. In mid 1998 oxygen enrichment of the Ausmelt lance air was introduced to expand the capacity to the throughput of 40,000 tonnes per annum of concentrates. The process route involves the use of an Ausmelt furnace for primary concentrate smelting, followed by a conventional tin pyro-refining circuit to produce high grade tin suitable for sale. Further work continues between Ausmelt and Funsur to investigate the use of an alternative, more economical, fuel source and the installation of a second Ausmelt furnace. The paper reviews the project to date with details of ongoing operations and developments at the Minsur Tin Smelter.

Jan 1, 2000

By E. A. Werner, A. Pichler, A. Spalek, G. Reisner, P. Stiaszny

"Interstitial free (IF) sheet steels are used for complex shaped parts because of their excellent formability. If a deep drawn part is subjected· to a impact deformation at low temperature brittle fracture of the part may occur. This phenomenon\ is called secondary work embrittlement (SWE). One possibility to characterize this material/structural behavior is the drop-weight test. The result of .this .test is a temperature at and below which a crack can initiated in a deep drawn part under the investigated set of parameters. This paper addresses the influence of the preforming process on the sus- . . ceptibili.ty of IF steels to SWE.IntroductionInterstiiial:free (IF-) steels are frequently used in the automotive industry for complex· shaped p·arts because of their excellent deep drawability. The microstructure of the steel consists of a highly ductile ferritic matrix with embedded precipitates of nitrides and/or carbides. Brittle fracture can occur in deep drawn parts, if they are subjected to a high speed deformation at lo""w temperature. This phenomenon is called ~econdary Work gmbrittlement (SWE) [1-11]. Up to now there are no standardized testing procedures available to quantify the sensibility of IF-sheet steel to SWE. Neveitheless, a reasonable testing procedure which allows to quantify the tendency of a predeformed part to SWE is necessary for further material development. A commonly used test method is the drop-weight test performed at low temperatures. In such ·tests a cone-like drop weight expands a deep drawn cylindrical cup [l-3, 6, 8, 9, 11]. From this expansion experiment the temperature is determined at and below which a brittle crack can be initiated in the deep drawn cup under the investigated impact test parameters. The highest measured temperature at which a deep drawn cup fails by brittle fracture is called frack appearances !emperature (CAPT). The lower the value of the CAPT the lower is the sensibility of a deep drawn part of IF-sheet steel to SWE. This paper aims to clarify the role of the preforming process on the impact behavior of an IF steel. For this purpose a numerical analysis of the deep drawing process and cup expansion tests are conducted."

Jan 1, 2000

By V. V. Satya Prasad, A. Sambasiva Rao

Electroslag melting technologies have recently been developed for recycling light scrap of valuable metals and alloys such as superalloys and oxygen free high conductivity (OFHC) copper at Defence Metallurgical Research Laboratory (DMRL), Hyderabad. Conventionally, electroslag melting processes use consumable electrodes. Because of the difficulty in compaction of scrap into a consumable electrode of satisfactory quality, non-consumable electrodes such as graphite and water-cooled copper have been designed. Electroslag remelting using a water-cooled non-consumable electrode was developed to melt scrap of a nickel base superalloy. Sound ingots with smooth surface finish and properties comparable to vacuum melted superalloys could. be obtained from scrap using this process. A modified electroslag crucible melting process using graphite crucible and graphite electrode was developed for recycling OFHC copper scrap. Copper ingots with less than 10 ppm oxygen and electrical conductivity"" 100% IACS could be produced. The same process was also utilized to produce copper-based alloys such as copper-chromium and copper-titanium starting from copper scrap.

Jan 1, 2000

By M Gao

Six new IsaMills were installed for the George Fisher flowsheet in the Lead/Zinc Concentrator of Mount Isa Mines to produce a product P80 as fine as seven microns. The objective was better liberation of galena and sphalerite. The IsaMill commissioning was completed by the end of 1999. The six new IsaMills were running to the metallurgical specifications almost immediately after start-up. This paper reports the performance of the George Fisher IsaMills in the zinc circuits and some of the latest development in the IsaMill designs and maintenance during George Fisher commissioning.

Jan 1, 2000

By M Scamardella

The CSA Mine is located at Cobar, New South Wales, where it was in continuous operation from 1966 to the time it went into receivership on 29 January 1998. When it closed it was under the ownership of Golden Shamrock. Glencore International, in conjunction with Mt Lyell Mining, undertook a due diligence study to determine the feasibility to re-open the mine. This envisaged operating CSA Mine as a low-cost, copper concentrate producer under the direction of Cobar Management Pty Ltd (CMPL). The new workforce would consist of contractor trades people in operating functions under the co-ordination of CMPL staff, both on the surface and underground. This was the key to establishing the new culture in the workforce. The orebodies at CSA Mine are steeply dipping with copper-lead-zinc mineralisation in zones of strong alterations in a fine-grained siltstone host sequence. The predominant economic minerals are chalcopyrite, sphalerite and galena. The major gauge minerals are pyrrhotite, pyrite, chlorite, sericite and quartz. Ore for the project is being developed and mined from two high grade copper lenses within the QTS North system. Chalcopyrite occurs in two forms. The first consists of coarse chalcopyrite grains in association with pyrrhotite or pyrite. The second form consists of chalcopyrite grains intergrown with pyrrhotite grains. This form of chalcopyrite is quite rare. It allows electrochemical interactions between grains, resulting in rapid oxidation of the chalcopyrite surface. Physically this ore looks like, and has been mistaken for æpeacock oreÆ, ie bornite, but is infact oxidised chalcopyrite.

Jan 1, 2000

By A. Z. Toper

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM An extensive research programme to address the issue of rockburst control has been undertaken over a number of years. This paper discusses the development of preconditioning techniques to control face bursts, for safer mining in seismically hazardous areas. Preconditioning involves regularly setting off carefully tailored blasts in the fractured rock immediately ahead of a mining face, so as to encourage slip on pre-existing fractures, in order not to allow the accumulation of high strain energy density in the rock mass. Two different preconditioning techniques have been developed, namely face-perpendicular preconditioning and face-parallel preconditioning. Both have prevented face bursting in areas to which they have been applied, even though several large seismic events have occurred close to the faces in some areas. In addition, minimal overall damage was observed in the preconditioned panels following these events, compared to similarly exposed unpreconditioned panels. Preconditioning has also provided some protection to the face area from distant events, through the capacity of the preconditioned ground to absorb energy. An improvement in hangingwall stability and productivity has also been noted in preconditioned areas. In order to determine the optimum blast parameters for achieving the most effective preconditioning, an extensive optimization study was carried out for the face-perpendicular preconditioning technique. While optimum values for parameters such as hole length, diameter and spacing were determined, it was ultimately concluded that the differences in results obtained by varying the preconditioning parameters were less significant than the clear positive differences observed when comparing preconditioned areas with non-preconditioned areas.

Jan 1, 2000

By Nobuo Kikumoto

Recently, the treatment of industrial waste materials has been a serious social problem here in Japan. Filling them in ponds is now strictly prohibited due to a limited land area and incineration method is also regulated as not to generate DXN. In these conditions, Onahama Smelter has begun to treat shredder dusts (SD) of car at reverberatory furnaces to recover various metals such as copper, gold, silver and palladium without generation of DXN. The total volume of these dusts is expected more than 1 million metric tonnes a year in Japan. Onahama Smelter is now planning to treat about 20% of them in the near future by using tonnage oxygen. In this paper, the heat balance, control method of DXN and treatment of these dusts in reverberatory furnaces are described. DXN : Dioxin (The generic term of PCDD and PCDF)

Jan 1, 2000

By Dale Preece, Stephen Chung, D. Scott Scovira

The DMC_BLAST (Distinct Motion Code) has been developed to model rock motion and displacement during the gas expansion phase after the detonation of an explosive in a borehole. Recently, a designated delay firing order algorithm was written into the DMC_BLAST code. The model can now be used to analyze rock mass displacement for a V-cut, center opening, or sinking cut initiation sequences. This new feature allows the investigation of the effects of delay firing order on rock displacement when blasting complex inter-bedded and ore-waste structures. The model provides important ground movement and mixing indicators for dilution control in surface gold mining relative to the initiation sequences employed. Echelon blasts as compared to center opening type blasts show differences in their internal muckpile displacement. These displacement differences can be important to operations that mine narrow strike driven ore bodies. The model also has applications to through coal seam blasting and demonstrates that down-dip blasting is a better alternative than up-dip blasting. There is less disturbance to the dipping coal seam and less mixing of the rock and the coal.

Jan 1, 2000

By M Titley, M NoppT

A study on the feasibility of mining the recently discovered Wallaby gold deposit is due for completion by mid-2000. Open pit mining is the favoured method. Determination of the impact of mining bench height on the recovery of ore, including the estimation of dilution and ore loss, is critical to the economics of the operation. Conditional simulation was used to derive a number of gold estimation scenarios within a typical volume of the deposit. These scenarios were interrogated for a selection of mining bench heights and ore block dimensions. The results were reported as a range of grade tonnage relationships and compared to the kriged resource model. This allowed the resource model to be calibrated to a specific mining bench height and ore block size. Once calibrated, more realistic dilution and ore loss values for a number of mining bench heights were calculated from the resource model. These values were then used to determine the economic sensitivity of particular mining methods. The spread of results from the simulations also provided an indication of the confidence in the kriged grade estimates for the different zones of mineralisation within the deposit and highlighted areas of any significant uncertainty.

Jan 1, 2000

By B. Cavender

Investments in new technology are often intended to improve the production or cost performance of existing operations. The economics used to justify these projects can be flawed, however, if they do not adequately consider the potential benefits of the alternative: the fully optimized use of the facility's present equipment and personnel. While new technology can be effective, dramatic improvements in production performance can also be achieved through the rigorous application of standard industrial engineering and operations management practices. An intermediate approach may also be effective: many basic improvements in the mine or plant necessary to support new technology will be equally effective when implemented for the facility's present operators. Firms that optimize their present operations are able to save the capital and avoid the risk associated with new technology. These firms will also be able to capitalize more quickly on new technology when it is implemented.

Jan 1, 2000

By D M. Weedon

This paper introduces a novel roll crusher design, which incorporates non-cylindrical crushing rolls. The use of non-cylindrical rolls enables the crusher to achieve a greater reduction ratio than is possible with conventional roll crushers. Referred to as the NCRC (non-cylindrical roll crusher), the new crusher incorporates two rolls comprised of an alternating arrangement of plane and convex or concave surfaces. The two rolls are complementary and arranged so that when they rotate the convex and concave surfaces of each roll are substantially opposed. With the rolls rotating in opposite directions at the same speed, this arrangement produces a gap between the rolls that remains approximately constant. Discontinuities on the roll surfaces provide improved angles of nip, which increase the probability of larger particles being drawn into the crusher. Initial tests on a scale prototype of the NCRC have indicated that reduction ratios exceeding 10:1 are achievable.

Jan 1, 2000

By P Bartlett, K Naidoo

Premier Diamond Mine is planning a new, mechanised, block cave, with a production level approximately 1000 m below surface. A high degree of tunnel damage is expected, due to stress and the relatively low in situ strength of kimberlite. An evaluation of the timing of tunnel excavation, tunnel size and spacing has been carried out to define critical parameters for planning layouts and development schedules. Extensive use has been made of three-dimensional FLAC3D numerical models, calibrated against known rock mass behaviour at 650 m depth, to examine the influence of undercut advance on production level excavations. These were able to represent the effect of stress rotation on tunnels during undercut advance and the effect of an inclined undercut. The analysis has provided guidelines that are possibly applicable to any deep block cave layout. The choice of drawpoint layout is of considerably less significance than the proportion of ground extracted on the production level elevation prior to advancing the undercut. The analysis shows that damage to production development will be potentially severe if it is all excavated prior to advancing the undercut, or is mined directly beneath the undercut face. The development of the main production tunnels alone ahead of the undercut may be feasible, but no breakaways should be put in as they appear to trigger a rapid increase in the severity of damage. The optimal sequence is when all production tunnels are developed at least 10 m in plan behind the undercut, where the induced peak field stress is less than 20 MPa and a maximum support pressure of 100 to 500 kN/m2 is require to contain movement. The assessment showed that the conditions are not significantly improved by increasing drawpoint spacing from 15 m to 18 m. The vertical spacing between the undercut and production level beneath is investigated. Provided production level development is carried out beneath the undercut, there would appear to be little benefit in increasing the vertical spacing between the undercut and production level beyond the current 15 m to 18 m.

Jan 1, 2000

By M Mee, R L. Gwyther

Accurate measurement of rock mass response during the mining of massive underground orebodies is essential, as mines become larger and deeper. These measurements enable: provision of quantitative data for optimal pit slope design and engineering; monitoring of the stability of deep pit slopes, the long-term integrity of shafts and large-scale underground infrastructure, and long-term measurements of deformation or rock mass creep following the mining process for environmental management. Strainmeters traditionally used for deformation measurement have neither the long-term stability nor the high sensitivity to perform measurements in these applications. This paper describes a new precision borehole strain monitoring system (GTS) currently deployed by CSIRO Exploration and Mining, which has the potential to solve these new issues in rock mass deformation monitoring. This technology was originally developed for use in hard rock mines (Gladwin, 1977) and refined considerably for earthquake research (Gladwin et al, 1994; Gwyther et al, 1992). A case study of the use of the GTS in monitoring longwall coal mining over the period 1993 - 1998 is presented.

Jan 1, 2000

By T. R. Rehak

Blasting operations are an essential element in the recovery of our Nation?s mineral resources. The mining industry uses billions of pounds of explosives annually. The majority of blasting occurs in surface mining operations. Blasting results in the fragmentation and often the projection of rocks. Frequently, the rocks are thrown beyond the expected limits. Flyrock and failure to secure the blasting area dominate blasting-related accidents in mining, especially in surface mining. Blasting accidents in the mining industry tend to result in critical injuries or fatalities. Accident reports and information collected from the Mine Safety and Health Administration (MSHA) and other government agencies provide supporting evidence. According to the data collected, blasting-related accidents (in mining) were 11 times more severe than all other types of mining accidents. Blasting accidents are not unique to mining operations - the same situation exists in the construction field. In this paper the authors have compiled a list of the primary causes of flyrock and the failure to secure the blast area. In the next phase of this project, typical blasting scenarios will be reviewed which will highlight the main reasons flyrock and/or lack of blast area security occur. This will alert miners and construction workers to the current problems/hazards associated with blasting and to identify other safety measures to protect personnel.

Jan 1, 2000

By T Blyth, D Holden, N Archibald, S Huffadi

The Morning Star mine is owned by Hill 50 Gold NL. Gold is hosted in quartz-carbonate ¦stibnite ¦molybdenite veins that occur in a series of deformed, altered and metamorphosed mafic volcanics with subordinate sediments and felsic intrusive rocks. The irregular gold distribution and its relationship to structure and alteration intensity makes the definition of stoping limits difficult. Understanding the structural evolution of the orebodies and the contemporaneous and later structures that affect the orebodies has been very useful in this context. This paper reports on a detailed mapping exercise (as part of a more extensive and on-going investigation) and the integration of this mapping with other geological and grade control data in a 3D modelling environment to provide an expanded basis for stope design. Three types of mineralised zones can be discriminated based on the morphology of the veins within. They are:those associated with strongly folded, thick veins (approximately 1 m thick eg 05 orebody); those comprising planar, boudinaged and some folded veins which consolidate to form tabular, steeply dipping bodies (eg 010 orebody); and zones containing the above vein types and thin, highly deformed veins within zones of intensely foliated country rock that result in localised, irregularly distributed high-grade gold zones (eg 02 orebody). The mineralised zones associated with thick folded veins are typically predictable over many tens of vertical metres. The second and third types of ore zone is generally less predictable. Detailed mapping and structural kinematic studies indicate all ore zone types are affected by progressive deformation involving strong strain partitioning. It is interpreted that high strain zones, recognisable by intense foliation development and highly deformed veins, are the latest stage of a progressive deformation which approximates bulk flattening. Structural controls on mineralisation can be defined at two different scales.Regional scale folding has deformed a sequence of mafic volcanics with interlayered sediments and felsic intrusives. Initial geometry of felsic bodies relative to orientation of the primary lithological layering and the bulk shortening direction is interpreted to be critical for initiation and development of strongly dilatant zones within this package of rocks, and Local scale dilation is evidenced by development of several vein sets whose range in orientations and opposed vergence relationships suggest a pre-folding origin comprising both extensional and hybrid shear-extensional types. Continued deformation resulted in folding of these veins with strong strain partitioning. Major vein packages are closely spatially associated with the felsic/mafic contact and an interpreted early structure which appears to have partitioned early dilation. This structure is now obscured by strong deformation but is currently represented by a zone of planar veins.

Jan 1, 2000

Determining the controls of high-grade mineralisation at Vera Nancy requires careful data collection and assessment on a global and specific deposit basis. The techniques developed over 60 years ago to analyse structure, grade and width data are just as applicable today and can be enhanced using modern geological modelling software. High ore grades at Vera Nancy are controlled by both the primary geometry of the mineralised structure and the intersections of the main mineralised veins with subordinate splay veins. The main mineralised structure dilated as a consequence of extensional tectonics while the splays acted as conduits bringing oxidising surficial fluids into mixing zones precipitating high gold grades. Near-mine exploration is focussed on identifying zones of vein flexure and splay interaction to locate the relatively small high-grade shoots. Data modelling in a 3D environment is an essential process for understanding the geometry of the system being explored.

Jan 1, 2000

By C. Rodgers, E. (Ted) Warren

"LocationThe Key Lake operation of Cameco Corporation is located at latitude 57°N in northern Saskatchewan, within the southem boundary of the Athabasca formation. The nearest city is LaRonge, located 240 km to the south. Access to the mine is by all-weather road and by private airstrip.Description of OperationThe mill was designed to produce twelve million pounds of uranium oxide (U3O8) a year from a feed grade of 2.4% U3O8. Current production is fourteen million pounds from 2.0% feed.Following grinding, the uranium is leached using sulphuric acid and oxygen in autoclaves. An eight thickener counter current decantation (CCD) circuit is used to separate the uranium-bearing solution from the solid waste residue. The uranium in solution is further purified in a solvent extraction circuit. The purified uranium is then precipitated using ammonia, calcined at 840°C, and packaged in drums for shipping to refineries. There is a crystallization circuit to recover excess ammonium sulphate produced in the process, and a waste treatment circuit.HistoryUranerz Exploration and Mining discovered the Gaertner and Deilmann orebodies in 1975 and 1976, respectively. Between 1975 and 1977, Uranerz conducted laboratory studies and delineated a process for the Key Lake ore known as the ""Bonn process."" In 1977, Sherritt Gordon Mines Ltd. was retained to conduct further studies in cooperation with U ranerz. The technical feasibility of the Bonn process was generally confirmed. Howeve1~ alternative processing methods also appeared feasible, and over the period 1978-1979, a detailed research and development program was conducted to finalize the processes to be used and to provide data for design of the plant."

Jan 1, 2000