Search Documents

By Frame Ritzert, Dennis Keller, Vijay Vasudevan, David Arenas

"An investigation was conducted to describe topologically close packed (TCP) phase instability as' a function of composition in the advanced ·Ni-base superalloy Rene N6. TCP phases are detrimental to overfill high-temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements. Thirty-four variations of polycrystalline .Rene N6 determined from a design-of-experiments approach were cast and homogenized at 13 l5°C for 80 hours followed by exposure at 1093°C for 400 hours to promote TCP formation. The alloys had the following composition ranges in atomic percent: cobalt 10.61 to 16.73, Mo 0.32 to 1.34%, W 1.85 to 2.52%, Re 1.80 to 2.11%, Ta 2.36 to 3.02%, Al 11.90 to 14.75%, and Cr 3.57 to 6.23%. Physical and chemical characteristics of all microstructures obtained were described using various analytical techniques. From these observations, a mathematical description of TCP occurrence (s and P phase) was generated for polycrystalline Rene N6.IntroductionNi-base superalloy single crystals represent the state-of-the-art for turbine engine airfoil application as they offer the best balance of properties to allow for the high operating temperatures required: for efficient engine operation.1 Current trends in alloy design take advantage of improved creep rupture strength with the addition .of higher levels of refractory elements. 2 In .particular, the addition of significantly higher levels of Re in third generation superalloys is key for both microstructural stability and creep rupture strength. 3 While the presence of the refractories is thought to provide strength benefits from solid solution hardening, a tendency for alloy instability in the form of topologically-close-packed (TCP) phases or secondary reaction· zone (SRZ) ·phenomena accompanies the high refractory content. 3 The formation of these phases in sufficient amount is detrimental to the overall high temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements.4 The tendency for a particular composition to form TCP may not be immediately known since the precipitation of TCP phases in Ni-base superalloys is nucleation controlled, thereby requiring long times at elevated temperatures to precipitate. 5 They preferentially nucleate along the octahedral planes of the Ni-base superalloys, usually in areas of refractory metal enrichment at grain boundaries or inside dendrites.5-6 In Rene N6, two closely related TCP phases, a and P, have been observed.2"

Jan 1, 1998

The Mt Lyell Mine at Queenstown, Tasmania was re-opened in 1995 by Copper Mines of Tasmania Pty Ltd, a wholly owned subsidiary of Mt Lyell Mining Co Ltd. The re-opening followed over 100 years of copper and gold mining at Mt Lyell. Major changes in practice were implemented across the site. Preventing further damage to an already disturbed environment was a major priority. Sublevel caving, at a lower cut-off grade, replaced open stoping for the deep underground mining. Development and later stoping are handled by a contractor, National Mine Management Pty Ltd, in the largest underground contract awarded at the time. Large scale sublevel caving was new to Mt Lyell and not widely practised in Australia, requiring studies and systematic development of the method, particularly in drilling and blasting. Rehabilitation and upgrading of mine infrastructure have been and will continue to be a challenge. The mine has, since 1995, returned to being a stable producer with potential for growth.

Jan 1, 1998

By Malcolm J. A. Swallow

In June 1997, Mount Polley Mining Corp., a division of Imperial Metals Corp., completed an 18-kt/d (20,000 stpd) gold-copper mine in central British Columbia. Fast-track construction and extensive off-site construction were combined with an aggressive project schedule to build the mine in one year. This was three months ahead of schedule and 7% below the original budgeted cost of C$123.5 million (US$86 million). The Mount Polley Mine was the first of a crop of new open-pit mines in British Columbia. The Mount Polley deposit has been explored since the mid-1960s when it was known as the Cariboo Bell property. From 1988, Imperial Metals completed drilling and metallurgical testing on the deposit. This led to a positive feasibility study and the issuing of a Mine Development Certificate in 1991. The project was later shelved due to falling metals prices and the strength of the Canadian dollar. In late 1994, Imperial merged with Bethlehem Resources Corp., bringing a strong project team to the company. The deposit was then re-evaluated, ore reserves revised and additional metallurgical testing was performed. The result was a revised project plan. It indi¬cated that a financially feasible gold-copper mining op¬eration could be constructed at Mount Polley operat¬ing at 18 kt/d (20,000 stpd). In May 1996, an agreement was reached with Sumitomo to jointly fund and develop the project. By early 1996, final plans and permits were being prepared for construction, scheduled to begin in June 1.996. On-site work commenced on May 28th, 1996 following lifting of the road restrictions. Mount Polley Mining acted as its own project manager. Construction was completed in June 1997. Plant runup took place in July and full production began in August. Through the use of off-site construction and the careful selection of contractors who cooperated to complete some 12 major contracts, it was possible to reduce the mine and mill construction time from 16 to 13 months. Off-site construction for all possible aspects of the work and the use of used milling equipment allowed significant savings in overall capital costs of construction. Total costs for the mine, mill and tailings dam equated to C$6,100/t/d of throughput. The mill design incorporates several innovative features that will aid maintenance and allow flexibility of operation. The operation is designed as a closed system and meets the latest environmental standards. Concentrate is shipped by truck to the port of Vancouver. Revenues for the mine come from the mine's production of about 3.1 t/a (100,000 oz/year) of gold and 10.8 kt/a (24 million lbs/year) of copper during the first four years of the 12-year mine life.

Jan 1, 1998

By S. Mason

Many organizations are realizing that continual improvement in health and safety relies on addressing the potential for various forms of human error. Of these, violations are often the most frequent form associated with accidents. These occur when an individual, or individuals, deliberately contravenes established and known safety rules. They have been associated with up to 90% of accidents and incidents in some industries and yet rarely receive the systematic attention they deserve in the promotion of safety. This paper presents underlying motives which cause violations. These can vary significantly from mine to mine and from job to job. Managers need some measure of attitudes to determine the underlying motives behind violations if they are to determine effective strategies for promoting safe behaviour. Questionnaires form the starting point to address attitudes and the motives behind rule violations. The choice of the most suitable questionnaire, however, will vary from organization to organization. Guidelines on the choice of questionnaire are offered.

Jan 1, 1998

Drilling and blasting operations have historically been viewed as a necessary 'evil' part of mining, whose costs should be minimised by whatever means possible. In the past, when operations depended primarily on crushing and milling for ore re

Jan 1, 1998

By Kiyoshi Shibata

A new assessment model has been proposed for metal production and its recycling system. The model consists of three processes, smelting of ore, cascading and upgrading of metal scrap. The present approach is to assess the total energy consumption of the system, by introducing two equations for describing the relationships between critical impurity content and the mass of production or scrap recycling. The total energy consumption in the system can be described as a function of recycling rate and performance of the upgrading process. The present model suggests that the impurity removal efficiency and yield in the upgrading process are essential to reduce the energy consumption in the systems. Especially, such points should be explicitly controlled in recycling of aluminum. The potential capability of this model was also discussed by obtaining several quantitative information required for the process design and the operational control of beneficial recycling of metals.

Jan 1, 1998

By J. Gao, H. O. Gekonde, S. V. Subramanian

"The functional role of inclusions at low cutting speeds is to promote ductile fracture in chip formation process, whereas the role of inclusions at high cutting speeds is to prevent tool crater wear by suppressing the tribological phenomenon of seizure at the tool-chip interface. Glassy oxide inclusions are engineered into the workpiece to form a viscous layer in-situ at the tool-chip interface at high cutting speeds. The viscous layer lubricates the tool-chip interface to prevent the seizure. In comparison with the large volume fraction of inclusions needed for promoting ductile fracture at low cutting speeds, the amount of inclusions required for lubricating the toolchip interface at high cutting speeds is very small and is in the range that is typical of clean steels. The chip fracture process at high cutting speeds is aided by strain rate hardening of the matrix, which facilitates chip disposal of relatively clean steel.Inclusion engineering for high speed machining involves the control of the rheology and composition of inclusions to meet target viscosity at the tool-chip interface. The application of thermodynamic models in controlled production of inclusions in steels designed for high speed machining is discussed."

Jan 1, 1998

By H. H. Murray

Industrial usage of clays for current and new applications will continue to grow into the next century. The rate of growth will be highest in the less developed areas of the world. Transportation costs are a significant part of the delivered price, so the location of reserves and processing facilities for kaolin, bentonite, and palygorskite (attapulgite) are reviewed relative to serving these emerging markets. New value added applications will increase in the more developed areas which will require high quality raw materials, more sophisticated processing, and rigorous quality control.

Jan 1, 1998

By Laurel E. Burns

Alaska is in competition with the rest of the world for exploration dollars. Providing a "seed package" of airborne geophysical data for the state's numerous mining districts encourages companies to begin more detailed exploration in more areas than they could have afforded on their own. When data are already available, the initial risk decreases for people involved in exploration. Airborne magnetic and electromagnetic data help ge¬ologists and geophysicists determine what rocks and structures are present under overburden and vegetation. These data form a fundamental package that exploration companies want before intensively exploring most regions. Individual mining companies have conducted their own geophysical surveys during the past several decades. However, these data are not available to other companies. The companies able to afford geophysical surveys have less money for ground exploration after purchasing expensive, private geophysical data. Therefore, they are not able to explore as many places as they might. Additionally, since data are not shared with other exploration companies, the proprietary surveys do not foster intercompany competition to move projects forward. Individual prospectors and small companies can not afford their own geophysical surveys. "It is more often than not the grassroots exploration efforts of the smaller operator that leads to significant discoveries," said Klaus M. Zeitler, senior vice president for development and exploration at Teck Exploration. Acquiring and releasing the geophysical data to the public produces several benefits. The increased explo- [ ]

Jan 1, 1998

MIM Holdings Limited (MIM) committed to a long-term future in copper in the Carpentaria Mineral Province in 1996 with the development of the Enterprise and Ernest Henry mines, and an upgrade of MIMsÆ copper smelter in Mount Isa, and copper refinery in Townsville. The upgrade of the copper smelter will enable the smelter to produce 250 000 tpa of copper with a single primary smelting unit, the copper Isasmelt furnace installed in 1992. The copper Isasmelt furnace currently smelts concentrate containing 145 000 tpa copper. To reduce the risk associated with the copper smelter upgrade, and shorten the ramp up time of the upgraded smelter, two high-rate trials were undertaken in 1997 to demonstrate that the copper Isasmelt furnace could, with an additional 525 tpd of tonnage oxygen, treat concentrates containing 250 000 tpa copper. During the trials the concentrate feed rate to the Isasmelt furnace was increased from its average rate of 100 tph of concentrate to 150 tph of concentrate. The increase in the capacity of the furnace was achieved by: supplementing the installed tonnage oxygen capacity of 595 tpd with an additional 300 tpd supply; reducing variability in the furnace feed rate from ¦25 per cent to less than ¦5 per cent; and reducing tramp air. The Isasmelt furnace smelted concentrate at a rate of 140 to 150 tph for four hours 25 minutes during Trial 1, and at a rate of 150 tph of concentrate for five hours and 30 minutes during Trial 2. The oxygen utilisation was 100 per cent during the trials with the process remaining under control. As a result of the development work for the trials the average treatment rate of the furnace under normal conditions increased by ten per cent.

Jan 1, 1998

By Terry Mandziak

Typical leach mine operations recover gold values through the application of a dilute cyanide solution onto ore within an engineered facility. Key to the success of mining operations is the, containment and management of the cyanide solutions within the facility. Properly engineered' facilities will have containment systems that are both protective of the environment while enhancing solution recovery. This paper not only discusses general containment standards, but identifies state-of-the-art containment and monitoring practices;

Jan 1, 1998

By Larry M. Southwick

Steel mill electric arc furnace dust is a RCRA listed hazardous waste and its treatment and/or disposal are regulated by a complex set of rules. These regulations were originally established to encourage recovery and recycling of valuable components. For EAF dust, the more valuable constituents include zinc, lead, cadmium and iron. In fact, current trends are in the opposite direction, as the regulations have complicated the ability to commercialize new treatment technologies and created substantial roadblocks and liabilities for processors. As a result, almost half of the EAF dust generated in 1997 will be landfilled. The problems are compounded by difficult processing requirements, less than sterling examples of technology development and mechanical and operating problems. This paper explores some options to simplify the processing requirements and thereby easing difficulties in commercializing new technologies and expediting the recycling of recovered metals. Dust processing usually includes a simple step followed by two complicated steps. The simple step is fuming of heavy metals away from iron and other residues. The complex steps are (1) separating and purifying the heavy metals and (2) upgrading the iron residue. The first complex step can be simplified by producing an intermediate product that is amenable to processing by zinc refiners. This route benefits from the currently underutilized (by dust processors) resource offered by refiners, who have experience in and existing processes for separation and purification of zinc-based heavy metals. Various processes and their associated product options are reviewed and compared. Future directions for dust processing developments are suggested.

Jan 1, 1998

By Scott D. Long

"Abstract-Grass roots exploration has an emphasis on good precision at low (sub-economic) concentrations of an element, in order to identify "anomalies" which may lead to drilling targets. Although it is wise to have well-defined quality controls in place during early stage sampling, the control procedures at this stage tend to be rudimentary. When a deposit warrants detailed delineation, the need for accurate geological characterization and assaying of ore-grade rock must be supported by appropriate quality control procedures.As a project returns more promising results, and the likelihood of the project warranting a prefeasibility study increases, it is time to tighten quality assurance requirements and quality control protocols. Delays in instituting adequate quality control and verification procedures may lead to costly remedial actions that can also delay completion of the prefeasibility or feasibility study. Sometimes, as a project matures, the quality control and quality assurance aspects fail to keep pace with the changing nature of the work: an increasing emphasis on precise and accurate assaying of oregrade rock.A resource model is like a house of cards. The foundation of the house is the geological observations, the sampling methods and the geological interpretations performed upon those samples. Upon the sampling, which includes all the sub-sampling steps of sample preparation, rest the assay results. The quality of the assays can be no better than the quality of the sampling. Good assaying technique will preserve all biases and imprecisions introduced during sampling and sample preparation; it cannot remove them. If the sub-samples and/or assays are bad and must be redone, all the succeeding levels of the house of cards must also be rebuilt, or at least patched up.From geological observations, a geological interpretation is built, the quality of which is critical to the construction of an acceptable resource model. Geological elements are difficult to assess, and are not discussed here; they are dependent upon the expertise of the geologists involved. Geological knowledge contributes essential quality control elements to resource/reserve determinations (Sinclair and Postolski, 1999; Postolski and Sinclair, 1999).This paper consists of five sections: (1) overview of quality control protocols, (2) maintaining quality control of databases, (3) quality control of drill sampling, (4) optimizing crushing and grinding requirements, and (5) quality control of assay data acquisition."

Jan 1, 1998

By Shunli Zhang

Metals recovery from electronic scrap by physical separation may provide an alternative to the current recycling approach, through which halogenated flame retardants can result in hazardous dibenzo-p-dioxins and dibenzo-furans. On the basis of a complete sink-float analysis of personal computer and printed circuit board scrap, and in view of the advantages of dry processes for electronic scrap recycling by mechanical separation, air table separation is prioritized in an attempt to separate metals from plastics and glass involved. In the present paper, theoretical and practical considerations of air table separation have been detailed. It has been shown that air table separation is effective for recovering copper and precious metals from this specific waste stream. With the feed rate of 60 kg per hour, the combined grade and recovery of copper, gold, and silver attainable for the two heavy products produced by the air table used in the present study was shown in the following table:

Jan 1, 1998

By R D. Morri, D J. Alexander

The design and optimisation of mineral flotation circuits is currently performed using a combination of laboratory, pilot plant and full scale testing. Owing to the variable nature of flotation circuits and the complex nature of the flotation process, it is difficult to interpret the data collected from flotation testwork. JKSimFloat is a computer modelling package which is being developed to interpret flotation testwork data collected at the various stages of the mining cycle. The parameters derived from the program can be used to assess potential circuit configurations in both the design of new flotation circuits and in the refinement of existing operations. The aim of this paper is to outline the modelling methodology used in JKSimFloat and to outline how it can be used effectively to model data collected from either the laboratory, the pilot plant or the existing flotation circuit. The use of flotation model parameters in circuit evaluation will be demonstrated via the use of a case study based on data collected from ComincoÆs Red Dog lead flotation circuit.

Jan 1, 1998

By M Hood, X S. L, W J. T Daniel, H Gurgenci

It is believed that disc cutter shape affects rock fracture and therefore cutter performance and cutter life. However, the current generation of disc cutters is made of hardened steel and these cutters wear rapidly and consequently they are unable to maintain their original shape in strong and abrasive rock. This wear problem could be reduced if the cutter was made from a harder material. Unfortunately as material hardness increases so does the propensity for brittle failure. In this study the optimum cutter shapes were identified by studying the mechanics of rock/tool interaction. The results showed that bevel and wedge cutters are better than cutters with dome and flat edges. A new cutter was designed, based on this result, using a harder material to increase the life by a factor of 20.

Jan 1, 1998

By M. A. S. Martins, H. Medeiros, B. Y. B. Dos Santos

This paper contains the geometallurgical studies, performed for Mineração Rio do Norte bauxites, applied to a selected area belonging to Plateau Saracá III, referring to an exploitation period of one year and three months, approximately. It is worth mentioning that Mineração Rio do Norte has the biggest bauxite operation in Brazil producing 8,500,000 tons of concentrate per year. The studies included wide investigations directed to the final objective of establishing a precise mining and production planning, based on the different behavior of the distinct bauxite ores, when submitted to industrial processes. Geometallurgy can be defined as the study of the regionalization (space distribution) of the metallurgical variables of a mineral deposit. This study involves and integrates all process engineering, geology, geostatistics and mining planning, among others. The development and application of the geometallugical studies to Mineração Rio do Norte were motivated by several reasons and necessities, among them: 1. Improving the forecast of the amount of concentrate (metallurgical mass yield) produced; 2. Improving the equipment operational efficiency, providing a more homogeneous feed; 3. Conducting a more precise material balance that permits a better daily, monthly and yearly production control; 4. Improving the forecasts for the final products generated by each ore type; 5. Obtaining better knowledge of the behavior of several ore types, submitted to the different process unit operations; 6. Promoting adequate ore blending, producing an homogeneous feed during mining operation.

Jan 1, 1998

By Michel Boisvert

Noranda Metallurgy is presently completing construction of the new Noranda Converter (NCV) at its Home Smelter in Rouyn-Noranda. This capital investment of CDN$56M is the continuation of the Emissions and SO2 Reduction Program that was initiated in the late 1980s with the acid plant for Reactor off-gas treatment. The Patented Noranda Converter was developed and pilot tested at the Home Smelter in the early 1990s. The project will replace the Peirce-Smith Converters and enable sulphur fixation to be 'increased from 70% to over 90% by 2002 with an accompanying reduction of dust emissions to the atmosphere. The construction site is an extension of the present Noranda Reactor area. A number of existing facilities including the acid plant and process air supply were used to minimize the capital cost of the project. This paper provides a brief history of the Noranda converting process, the Home Smelter Emissions and SO2 Reduction Program, ,project implementation and construction, a description of the different facilities, and preparation of human resources for start-up.

Jan 1, 1998

By Garth James

Bacterial consortia capable of degrading cyanide and metal-cyanide complexes were obtained from gold mine process waters using enrichment cultures. The cultures contained either cyanide, tetracyanonickelate, or ferrocyanide as a sole nitrogen source. Several bacteria were isolated from the consortia, but none of these organisms were capable of degrading cyanide or cyanide-metal complexes at rates equivalent to those of the intact consortia. The consortium from the cyanide enrichment was capable of completely degrading cyanide from an initial concentration of over 100 ppm in less than one day, when cultured using a fed-batch method. Tetracyanonickelate and ferrocyanide were degraded more slowly. Overall, these results demonstrate that bacteria capable of degrading cyanide and cyanide-metal complexes can be isolated from mine process solutions and are capable of significantly reducing cyanide concentrations under appropriate conditions.

Jan 1, 1998

By D. W. Ginsberg, D. Cieplinski

"The lifetime cost of a material handling system, or any mine system, can be reduced through the application of quality engineering. Dynamic simulation is a powerful tool that can be used to enhance the experience and ingenuity of the design team. It cannot only de-bottleneck the system to improve system productivity, but also define critical design criteria to eliminate over-design and reduce capital cost. Eliminating over-design also reduces operating costs by lowering component replacement costs and by ensuring all parts of the system operate at a higher utilization and efficiency. IntroductionA mine owner’s profitability is improved when a mine is developed at the lowest lifetime cost. This cost relates not only to capital and operating costs, but also, to a great extent, on the efficiency and reliability of the operation. These factors are tied directly to the quality of the engineering which depends on the experience of the engineers involved, and their ability to apply known system information in a rational and constructive manner.It is becoming apparent that it is increasingly more difficult to deliver the quality of engineering expected and needed to provide attractive lifetime costs using traditional design methods. Historically, system information has been evaluated based on a limited amount of information to which global rules-of-thumb and the engineer’s personal experience were applied to develop design criteria. However, market forces are dictating that more system parameters be defined and that they be defined more accurately so that the most economical system can be developed. This increase in the volume of information and the need for more accurate predictions is straining, if not already exceeding, the ability of engineers to apply simple global rules of- thumb and to combine all the information in a rational, comprehensive and representative set of design criteria. Furthermore, as proposed system production rates increase beyond established industry practice, the extrapolation of the engineer’s experience becomes more difficult and increases the risk in the proposed design."

Jan 1, 1998