Search Documents

By G. L. Liu

"Deformation Banding ( DB ) in cold rolled mild steel has been experimentally established by microstructure investigation. Deformation banding model includes such deformation mode when it is applied to rolling texture simulation. The cause for the occurrence of deformation banding is the reduction of the total work for plastic deformation through a relaxation of the deformation constraints. In the first DB model, all grains are assumed to band from the first deformation step. Such an unrealistic assumption has been eliminated in the new model by the introduction of a banding criterion based on an energy minimizing approach. The prediction is closer to the measured texture by applying banding criterion and setting critical resolved shear stresses (CRSS) ratio for { 110 } and { 112 } slip modes to 0.85.IntroductionBased on the continuum theory of plastic flow and deformation mechanism of crystallographic dislocation slip, Taylor's FC ( Full Constrain ) theory [1] has been widely used in texture modeling. As the process of cold rolling of sheet materials produces a microstructure consisting of elongated or equiaxed flat grain or cell, the ""lath"" and ""pancake"" relaxed constraints ( RC ) models [2, 3] were introduced as the successful improvements over the classical FC model. It has been also recognized that crystals may split into different orientations during deformation and the term deformation banding is used to describe such deformation processes [4, 5]. Lee et al. [6, 7] pointed out that the success of the RC theory in predicting textures depends on the physical processes of deformation banding. They developed so called Deformation Banding ( DB ) model by considering DB in the longitudinal plane to be accounted for by the RC method and allowing DB in the rolling plane. DB model was applied to simulate the texture development in bee case [8], the predicted bee rolling textures are in reasonable agreement with the measured textures. In the first DB model, however, all grains are assumed to band right upon the first deformation step. A banding criterion was formulated [7] which states that DB will occur if the work used in DB model is less than that in RC model. Such criterion has been incorporated into the original DB model for texture simulation and is referred to as DBC ( Deformation Banding Criterion ) model."

Jan 1, 1998

By Glenn C. Miller

Cyanide is the most common lixiviant for extraction of precious metals, and its efficient use in open pit mines has contributed to the increase in world production of gold during the previous two decades. With this expansion of precious metals mining using cyanide, public concerns have developed in response to the inherent public perception of cyanide as a tox-in as well as a series of environmental problems that are directly or indirectly related to cyanide use in open pit mining. Some of these have technical or regulatory solutions, while others will require additional investigation before they can be resolved. The following discussion will summarize some of the public concerns regarding the use of cyanide in precious metals mining. The issue of cyanide use in large scale precious mining is controversial, and recent banning of cyanide use in open pit mines in Montana, or complete banning of cyanide in Hungary has reflected those international concerns. The underlying basis for some of the bans (e.g. Montana) reflect a general concern of the environmental impacts of mining, rather than specific issues related to risk of cyanide use. The human safety record for cyanide use, particularly in the developed countries is good, and cyanide is clearly the most efficient lixiviant for precious metals. Indeed, the relatively short lifetime for cyanide in the environment renders it one of the less problematic chemicals used for extraction of gold from ore. Mercury amalgamation or use of bromide as a lixiviant are certainly much more problematic. What, then, is the basis f~r the international concern about precious metals mines that use cyanide. Ifuse of cyanide for gold recovery is to continue, what additional infom1ation needs to be developed that will allow a better management of the risks of cyanide? Which of the concerns are directly related to cyanide, and which are indirect concerns that more related to effects of open pit mining. Under what conditions should use of cyanide be discouraged? DUl::ing June of 2000 the United Nations Environmental Program conducted a two-day workshop on cyanide use in mining that was attended by persons from the mining industry, regulators and environmental community. Support and attendance at this workshop reflected concerns by all three groups on further restrictions for cyanide use and the emerging potential for guidelines for better management of the catastrophic release of cyanide-containing mining waste. The following discussion is meant to focus-on those risks and explore the basis for an often negative reaction to precious metals mining using cyanide. It is presented in the format of a statement, followed by a discussion. While admittedly provocative, the statements are meant to express the concerns? of the public regarding cyanide and the mining industry.

Jan 1, 1998

By Tim J. A. Smith

Fundicion Refimet S.A. has operated a custom copper smelter at La Negra, near Antofagasta in northern Chile since 1993. From an initial operation based on Reverb smelting and Peirce-Smith, converting, the plant was expanded from 90 000 t/y to 160 000 t/y copper production in early 1997, by conversion to oxy-fuel smelting and use of concentrate injection on Converters. As part of this expansion a novel reverb gas cooling and cleaning system was developed and designed by Kilborn SNC-Lavalin Europe, the London, UK-based mining and metals; Office of Canada's SNC-Lavalin group. The reverb gas cooler needed to satisfy several very specific requirements including low cost, flexibility, robustness and simplicity of operation. Of particular importance was the requirement to cool and clean the ,oxy-fuel reverb gases and render them suitable for subsequent treatment in a conventional sulphuric acid plant. It was also important to avoid accretion or dust handling problems. This paper describes the key design features and subsequent successful installation, commissioning and operation of the unit.

Jan 1, 1998

The old Trekelano mining area is situated in the Cloncurry Gold and Mineral Field 14 km east-south-east of Duchess. It connected with the main Cloncurry-Dajarra railway line by a private line from Juenburra, a distance of 10 km. The distance by rail from Townsville is 561 km. The area was first mentioned circa 1902 - 1903 when a very short report said, that a Tony Allis had taken a parcel of copper ore out of a mine which, he called æThe InheritedÆ. After that report, nothing further was printed until about 1906, when traces of copper were noticed on a wagon track going to Kiama Well. The Trekelano deposit did not outcrop, with the cap covered by about two metres of soil. The deposit was named after an early pastoral holding. The early prospectors were however disappointed by TrekelanoÆs low copper grades, approximately five per cent Cu. This is understandable when, in those days, about 25 per cent was the cut-off grade for mines in the district. Meanwhile, The Hampden Mining and Smelting Company were constructing a smelter to treat their sulphide ores at Kuradala that was replacing their high grade oxides ore. By about 1910, the Hampden Mining and Smelting Company was experiencing smelting problems, and needed suitable oxidised copper ore to blend with the Kuradala pyritic ore. Someone must have remembered the Trekelano low-grade oxides, resulting in agreement to mine and cart the ore to Duchess, from where it was railed to Hampden, as Kuradala was known at that time.

Jan 1, 1998

By M Grossi, G Baiden

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and onsite applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no dewatering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

By William J. Miles

The inhalation of dust has been a problem in the mining industry since antiquity. Crystalline silica is now known to be the cause of silicosis, a form of pneumoconiosis that is associated with excessive exposure to respirable particles in some mining and industrial environments. Crystalline silica was reviewed by the International Agency for Research on Cancer (IARC) in 1986 and classified as a Group 2A, Probably Carcinogenic to Humans in Volume 42 and Supplement 7 of the IARC Monographs (1987). In 1996, IARC reviewed additional literature and studies published in the intervening decade and recommended that quartz and cristobalite, two polymorphs of crystalline silica, be listed as Group 1, Carcinogenic to Humans. Their recommendations and reclassification were published in 1997 in IARC Monographs 68.[2] In both Monographs, IARC classified amorphous silicas as Group 3, Inadequate Evidence for Carcinogenicity to Humans.

Jan 1, 1998

By K. J. Shoop

Coal-fired power plants in the U. S. produce approximately 20 million metric tons of Hue-gas desulfurization sludge every year. The sludge mainly consists of calcium sulfite and calcium sulfate. This can be converted to synthetic gypsum, which in principle could be a marketable commodity. However, many Hue-gas scrubbers produce sludges that do not meet the quality requirements of the gypsum industry, and so their sludges must be landfilled as a waste. If a suitable method can be developed for removing certain objectionable impurities from the sludge, it will then be possible to market the material instead of landfilling it. A sludge from a natural-oxidation scrubber was characterized, and the main contaminant was found to be calcium carbonate from unreacted limestone. Based on the particle size and the characteristics of the material, froth flotation was considered as a method for purifying the material. Since no flotation studies have ever been carried out to separate calcium carbonate particles from calcium sulfite or calcium sulfate particles, it was first necessary to select a suitable collecting reagent. Based on Zeta-potential studies, the most suitable reagent was found to be an octadecylamine-octadecylguanidine complex. Results are presented for flotation of calcium carbonate from scrubber sludge using this reagent, in a reverse-flotation process. The best results were obtained when the sludge was first pre-cleaned using a water-only cyclone to remove unfloatable coarse limestone, followed by froth flotation to remove fine limestone.

Jan 1, 1998

By L. Piga, G. Belardi, V. Alesse, N. Shehu, J. Freund

The physico-chemical interactions among minerals such as olivine, chromite and serpentine; the most commonly present ions in solution such as Ca and Mg; and flotation reagents such as EDTA and oleic acid were investigated. The study was conducted via release tests, electrophoretic measurements and microflotation of selected minerals coming from the Kukes deposit in Albania. The results were confirmed in beneficiation tests on two ores, one from the Kukes (Kalimash) deposit and the other from the Rizo deposit in Greece. It was demonstrated that, when Na-oleate is used as collector, chromite, olivine and serpentine can be separated at pH 2.5 and/or pH 5.5 when employing ethylenediamine tetraacetate (EDTA) on previously deslimed material. This approach ensures flotation concentrates with a Cr203 content better than 50% with a recovery of more than 75%.

Jan 1, 1998

By J. T. YIi-Penttiia

Dust formation and reaction mechanisms of copper matte particles were investigated in simulated flash oxidation conditions. The granulated and ground matte consisted of 72 wt% Cu, 4 wt% Fe and 21 wt% S. Experiments were conducted by using a laminar-flow furnace with a reaction gas composition ranging from 20 vol% to 75 vol% O2 in nitrogen. The particle feeding was carried out by the single-particle method and samples were quenched after a specified reaction time (approximately 0.05-004 s) in a cold water film. Experimental temperatures were between 800 and 1300°C. Chemical analysis was used to determine oxidation degree, and an optical and scanning electron microscope combined with energy dispersive analysis was used for characterization of the reacted particles.

Jan 1, 1998

By B. K. Slone

The depth at which it becomes more economical to use slope access as opposed to box-cut access for near-surface coal reserves, termed "transition depth," can be established for a given coal property by considering cost estimates for those parameters that determine respective access method. Fourteen parameters that influence access cost were identified and ranges determined. A Transition Depth Formula was developed to permit determination of the better method of accessing a reserve, given such information as highwall slope, road width, total bench width, pit dimensions, road grade, belt component costs, pumping costs, and cost of overburden removal and reclamation. In most cases, in Appalachia, studies indicate that the transition depth ranges between 20 and 30 m.

Jan 1, 1998

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modifying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (K. McDaniel, et al., 1997) to: identify and quantify operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project will be completed in early 1998.

Jan 1, 1998

By T. W. Mattioli

Restrictions on fugitive emissions and crushing operations continue to get tighter. Although fugitive dust control in the gold mining industry has historically been difficult, there are now several options that can make dust control both effective and efficient. Using new technology, mine operators can now design and maintain a dust control program that can reduce product losses, decrease equipment failure, cut cleaning costs, and meet air quality compliance standards as well as provide a better working environment. This paper discusses the sources of fugitive emissions related to the gold mining and crushing operations and describes effective new control methods.

Jan 1, 1998

By Thomas J. DeMull

Heap leaching was introduced to the precious metals mining industry approximately two decades ago as a simple, low cost method for recovering gold and silver from ores. Since that time, operational experience has contributed to knowledge and understanding of the process, making it a reliable alternative to conventional milling processes for low grade ores. At time of this writing, dozens of heap leach operations are active producing hundreds of thousands of ounces of gold and millions of ounces of silver annually. These successes have caused the popular press to acclaim heap leaching "high-tech" gold mining, but, despite the hype, the process remains a simple one. An example of simplicity in heap leaching is the operation established in 1986 at Amax Gold's Sleeper Mine. Starting with a simple goal, namely to produce gold from sub-mill grade ore at low cost, heap leaching was rapidly implemented at Sleeper; only five months after testwork started, leaching commenced on the first commercial scale, 50,000 ton heap of low grade ore. Sized at 600,000 tons per year to produce 10,500 oz gold per year, the low grade heap operation has performed beyond expectations. During the first year of production, 881,800 tons have been leached producing 15,665 oz of gold and 35,528 oz of silver. Operating ·costs for the first year have averaged $112 per oz gold produced ( or $95 per oz if silver credit is included). Successful implementation of heap leaching at Sleeper has had a dramatic impact on ore reserves and future operations.

Jan 1, 1998

By R. L. Zick

The High Density Sludge Process was originally developed by Bethlehem Steel Corporation for use on acid mine drainage and diluted waste pickle liquor discharges requiring continuous chemical treatment systems. This work began in the early 1970s and was first put into practical use around 1973. To date there are approximately 15 operating systems which have been installed on mine drainage in the United States, and another 10 systems worldwide. Dense Sludge is an innovative and improved method for treating acidic metal bearing streams in a manner which minimizes the volumetric generation of sludge for disposal. The technology utilizes a sludge recycle process which forms particles that have a low affinity for water, unlike conventional metal hydroxide solids which contain tightly bound interstitial waters. Typical acid mine drainage streams contain high sulfate concentrations which combine with calcium ions in lime based treatment systems to form gypsum crystals. The physical form of this gypsum is radically altered when the Dense Sludge process is utilized compared to the form generated in conventional lime treatment systems. The characteristics of the metals particles are also changed in this process, as the metal hydroxides are converted to metal oxides. Slides No. 1 and No.2 show scanning electron micrographs of conventional and densified sludges illustrating these differences. The magnification used was 300X. The dense sludge particles settle faster, dewater more readily, are more easily pumped, and hold much less water than conventional precipitates. In some cases, because the metal content of the sludge is more concentrated, it can be economically recovered.

Jan 1, 1998

Since it was first introduced, the Coal Mine Roof Rating (CMRR) has been widely accepted as a tool for geologic characterization and mine planning. This paper discusses the application of the CMRR to another practical ground control problem. Extended cuts (cuts greater than 6 m (20 ft) in length) are commonly used with remote control continuous miners. Extended cuts can greatly increase productivity, but they have been associated with a number of fatal roof fall accidents. When extended cuts are attempted in weak roof, the roof may collapse before it can be bolted, causing hazardous conditions. Until now, it has not been possible to predict where conditions may not be suitable for extended cuts. In this study, data on the CMRR and extended cut experience were collected at 36 mines in 7 states. It was found that when the CMRR was greater than 55, deep cuts were routine in nearly every case. When the CMRR was less than 37, extended cuts were almost never taken. Between 38 and 55, extended cuts were feasible sometimes but not others. The data also shows that extended cuts are less likely to be stable if either the entry span or the depth of cover increases.

Jan 1, 1998

Jan 1, 1998

By Chappell B

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to he placed in a tailings darn. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electro- osmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

By E. A. Metz

Silicon dioxide, silica, is the most common oxide in the earth' s crust. The health effects of silicon dioxide dust have been known since Biblical times. Agricola's book, published in the mid 1500's on occupational medicine, described a lung disease that afflicted miners. He observed a disease in miners that caused shortness of breath, coughing and wasting. Add fever, chest pains and fatigue and we have the current symptom complex of silicosis. As we approached the 21stcentury, the Labor Department began an aggressive campaign to combat silicosis-a preventable disease. Unfortunately, many publications do not clearly differentiate the polymorphs of silica known to mineralogists. Crystalline silica, i.e., alpha quartz, tridymite and cristobalite need to be considered differently from the amorphous forms of silica. Freshly fractured surfaces of the silica and host specific responses will be examined. Recent research focuses on the biologic interactions of free radicals generated by mineral particles. This results in cell injury and DNA damage, in turn leading to fibrogenesis and possibly carcinogenesis. In addition to particle-cell interactions, emphasis is given to lung defense mechanisms.

Jan 1, 1998

By P. G. Kovalchik

Recent research conducted by NIOSH, Pittsburgh Research Laboratory showed that electrical current levels permitted under present regulations may not limit cable temperatures to less than 90°C in reeled trailing cables. Reeled cables, tightly wrapped with many turns, all carrying current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften and become easily damaged. The damaged insulation reduces the life of the cable and can lead to shock, electrocution, and mine fires. This paper describes a method of measuring the conductor temperature of mine trailing cables during normal operation. The temperature is measured using a 50/125 micrometer Graded Index Multimode Optical Fiber located in the center of the metallic conductors. Distributed temperature measurements are made using an Optical Time Domain Reflectometer (OTDR). This system is capable of measuring temperature with an accuracy of plus or minus one degree centigrade over a length of 4 km at 1-m intervals. With this unique way of measuring temperature, tests can be conducted simulating actual mine conditions and provide important data to allow MSHA's Approval and Certification Center to develop approval criteria for cyclically rated reeled machines.

Jan 1, 1998

By B. J. Vorster

AngloGold South Africa region currently consists of 12 Gold Plants. These plants use a combined total of $20 million of cyanide per annum. Of this, the .major portion (60%) is consumed at two Ergo dump retreatment plants. Historically the primary motivation for cyanide control at Ergo has been one of leachlcost optimisation. However, more recently, with the increased public awareness of cyanide in the environment, a secondary but increasingly important motivation for control has been to ensure that only the minimum amount of cyanide is added to the process whilst not compromising leach performance. Following a brief overview of the Ergo process, the methodology in detennining the amount of cyanide to be added is described. The paper then traces the developments in cyanide control from very basic? manual systems to the current automated control system. In line with the increasingly sophisticated control systems, developments also took place in regards to the method of cyanide analysis. The development of these analysers is also discussed. Whilst cyanide is one of the major drivers, if not the major driver of gold dissolution, it cannot be viewed in. isolation particularly with respect to the relationship between cyanide and oxygen as ascertained from the Elsner's well known equation. Consequently, in order to control cyanide addition, knowledge of the relative cyanide/oxygen profiles is necessary. Various means investigated at Ergo for pulp oxygenation have therefore been included for the sake of completeness. Finally a comparison is made of the control achieved from the current system compared to the? original manual system. The knowledge and experience gained at Ergo is now being used to draw up guidelines for the installation and optimisation work at the other AngloGold plants. The net effect of this will be reduced cyanide consumption for the region, which also, apart from the obvious economic benefit, translates into a reduced environmental; risk.

Jan 1, 1998