Search Documents

By A. W. Dickerson

Following on from many years of research aimed at improving the effectiveness of truck haulage operations in mines operated by BHP Minerals, BHP Research developed a concept for an Innovative Large Mining Truck, (ILMT) which has the potential to significantly improve the cost effectiveness of rear dump mining trucks. The ILMT concept reduces the empty vehicle weight dramatically, greatly reduces unequal rear tyre loading and improves ride and handling characteristics. The concept has been taken to the "proof of concept" prototype truck stage with the cooperative efforts of BHP Coal, BHP Research, Liebherr Mining Truck, Inc., Liebherr-Australia and Birrana Engineering. Testing of the prototype truck commenced at a coal mine in Queensland, Australia during May 1996. Preliminary results from the testing program are very encouraging. Expectations are being met and in some cases exceeded.

Jan 1, 1997

By Linda C. M. Elliot, Liangxue Liu

"The deposition of tailings under water is considered to be one of the most environmentally promising and potentially cost effective methods to reduce or eliminate acid mine drainage from tailings. One of the concerns of subaqueous deposition has been that metals may leach into the cover waters, thereby increasing aqueous metal concentrations to higher than acceptable limits. This potential was seen to have an even greater possibility for impact when the tailings are deposited under acidic lake water.The following paper summarizes the results of subaqueous tailings pilot column test work conducted to determine the effects of subaqueously deposited tailings on lake water and tailings pore water. Two types of tailings were tested: high sulphide tailings (pyrrhotite concentrate), and low sulphide tailings (end of pipe slime tailings).Data was collected from five columns over a 13 month test period. The results indicated that a stagnant I 000 mm water cover was capable of maintaining the underlying tailings in a reducing condition. The upwards diffusion of pore water resulted in a pH increase in the waters overlying the thickened pyrrhotite tailings and the pyrrhotite tailings with a shallow cover of substrate. A conductivity gradient between the tailings and the water cover caused a diffusion of salts upwards into the overlying water column. Precipitation noted at the tailings water interface may be related to the precipitation of ferric oxyhydroxides, which resulted in a decrease in Fe concentrations noted in the water cover. Other metal concentrations did not exhibit significant increases in the water cover. A sulphate concentration gradient between the tailings and the water cover may have caused the diffusion of SQ4 from the tailings into the water cover."

Jan 1, 1997

By H. Itou, J. M. Toguri, T. Takasu

"Marangoni convection has a large effect on materials processing since it remarkably enhances heat and mass transport near a free interface. To have a better understanding of the behavior of Marangoni convection in molten salts, observation and calculation of the thermal convection in a column held between a pair of Pt disks (2mm in diameter) fixed to hot thermocouples, were carried out.Calculated flow patterns and absolute values of fluid velocity agreed well with the observed results. When the temperatures of both disks were set equal and the height of liquid column was 2.4mm, four vortexes were generated on the longitudinal plane with a typical velocity of 15mm/s . From the calculated isothermal lines, the behavior of the enhanced heat transport was obvious; fluid heated at the disks was conveyed to the free surface and the cooled fluid at the surface was conveyed to the inner region. Increase in the height of column and/or increase in the absolute value of applied temperature difference lead to increase in fluid velocity lineally in this calculation range.IntroductionIn the processing of many materials, fluid flow of melts has a large effect on refining capabilities and on the characteristics of the produced material. Marangoni convection is generated when a spatial gradient of interfacial tension exists on the free interface due to differences in temperature and/or concentration. This promotes heat and mass transfer locally near the interface.For example, Marangoni convection which are created following the dissolution of interfacially active materials, increases the local corrosion rate of refractories (1-3). In absorption and discharge of oxygen and/or nitrogen in a molten metal, the effective reaction rate of the gas components through the gas-liquid interface increases (4-7). Also in crystal growth, the distribution of defects and impurities in the crystal is affected and this can alter its quality (8-11 ). The temperature distribution is also affected and can greatly change the productivity. For these reasons, the effectiveness of Marangoni convection in refining should be quantitatively clarified and its control should be better understood."

Jan 1, 1997

By M. Boher, J. Lehmann, M. C. Kaerlé

"In the production of high quality steel, the understanding of the interactions between liquid steel and refractories and of their effect on steel purity and cleanness are becoming more and more important.An experimental study has been per-formed in order to estimate the importance of the reaction between a MgO-based tundish refractory and an Al-killed steel. The results show a pollution of the liquid steel:•the silicon content of the liquid steel increases due to the reduction of the silica of the refractory by the aluminum contained in the steel; and•a reoxidation of the steel occurs and the formation of an oxide layer on the refracto-ry, mainly composed of spinel crystals and of Ca-aluminates is observed.The transfer mechanisms of the various elements are analyzed."

Jan 1, 1997

Resource rent tax is a form of taxation or royalty, which only become effective at such a time as a pre-determined rate of return has been achieved by an operation. The offshore petroleum industry in Australia is already subject to RRT as is the Roxby Downs (Olympic Dam) Mine in South Australia. Both the mining and petroleum taxation regimes in Papua New Guinea include a resource rent tax component called Additional Profits Tax (APT). The implications of the current form of Additional Profits Tax for shareholder cash returns are that the tax burden on the operation may suddenly increase at some stage in the life of the mine, if and when the threshold level of profitability for the tax to be triggered is exceeded. From that point in time onwards the cash return to the shareholders on the capital invested is greatly diminished. For mining companies in Papua New Guinea, the effective tax rate increases from 35% to 57.75% as a result of the onset of Additional Profits Tax. This tax rate penalty is so severe that there appears to be merit in considering the concept of managing profitability through time rather than purely maximising annual pre-tax profits as is currently the case in most mining operations. This would have the benefit of deferring or perhaps preventing altogether the onset of the tax. One possible method for the effective management of profitability is through the control of average mining grade by cutoff grade manipulation. Traditional cutoff grade theory has usually considered taxation as a direct cost at a fixed or variable percentage of annual profits. As a result of this most analyses are conducted on a pre-tax basis. If tax is included in analyses it is usually present as a time independent function of gross profit. Additional Profits Tax is both time and rate of return dependent and therefore not adequately accommodated by currently accepted cutoff grade theory. A review has been made of the effects of resource rent taxes on both the investment decision-making process as well as possible development and mining strategies which may be employed by mining companies faced with Additional Profits Tax. The review includes examples based on the structure of Additional Profits Tax which is levied in Papua New Guinea.

Jan 1, 1997

By S. L. Ducummon

Inactive underground mines now provide essential habitat for more than half of North America's 44 bat species, including some of the largest remaining populations. Thousands of abandoned mines have already been closed or are slated for safety closures, and many are destroyed during renewed mining in historic districts. The available evidence suggests that millions of bats have already been lost due to these closures. Bats are primary predators of night-flying insects that cost American farmers and foresters billions of dollars annually, therefore, threats to bat survival are cause for serious concern. Fortunately, mine closure methods exist that protect both bats and humans. Bat Conservation International (BCI) and the USDI-Bureau of Land Management founded the North American Bats and Mines Project to provide national leadership and coordination to minimize the loss of mine-roosting bats. This partnership has involved federal and state mine-land and wildlife managers and the mining industry. BCI has trained hundreds of mine-land and wildlife managers nationwide in mine assessment techniques for bats and bat-compatible closure methods, published technical information on bats and mine-land management, presented papers on bats and mines at national mining and wildlife conferences, and collaborated with numerous federal, state, and private partners to protect some of the most important mine-roosting bat populations. Our new mining industry initiative, Mining for Habitat, is designed to develop bat habitat conservation and enhancement plans for active mining operations. It includes the creation of cost-effective artificial underground bat roosts using surplus mining materials such as old mine-truck tires and culverts buried beneath waste rock.

Jan 1, 1997

By Jay S. Gunasekera

Metal parts are traditionally processed by either filly-liquid (e.g., casting) or filly-solid (e.g., forging) state. Semi-solid metal forming incorporates elements of both casting and forging. In 1991, Gunasekera(5) developed a model illustrating the influence of flow stress by the liquid fraction. The result fits Kiuchi's (1979)(7) experimental data quite well. This model assumed the liquid part is surrounded by solid as small pockets inside the material, which is opposite to the real practical situation. Since the melting usually first happens at the grain boundary, it is better to treat the semi-solid material as small metal crystal surrounded by liquid.

Jan 1, 1997

By Andy Schroeder

Located in Hamilton, Ontario Canada, Berminghammer Foundation Equipment, is a manufacturer of advanced foundation equipment with 30 years of experience. The company is represented in more than 20 countries world wide, maintains an extensive Research and Development team, and has earned a reputation for finding the most practical solutions to the most challenging projects. The vertical travel lead, referred to as "VTL" system, was first developed and patented by C.W. Bermingham in the 1970's. This lead system was developed in response to the fundamental limitations of either a fixed lead or hanging lead system. The fixed lead system is well suited to level job sites with few obstructions and has the advantage of faster positioning of the lead, the hanging lead is very adaptable to different elevations and batter piles but takes much longer to position. Therefore the Vertical Travel Lead was developed to combine the advantages of fixed leads, fast and accurate positioning, with the ability to adjust the height of the lead base up or down. The VTL lead is connected to the boom by a sliding connection which allows the lead to be elevated or lowered below grade. The advantages of the VTL system were recognized by many foundation specialists and they have become the Industry standard in Canada , US Railway Construction , and many parts of the USA.

Jan 1, 1997

By A. G. Jackson, Mark D. Benedict, Steven R. LeClair, Yang Cao, David M. Conrad

"Electronic Prototyping (EP) represents a new and powerful medium that many in science and technology view as the research paradigm of the future. Actually, EP has many handles, sometimes referred to as simulation-based design involving more long term objectives such as virtual reality, but regardless of the 'spin', the direction of EP is an enhanced visual paradigm to enable a new set of tools for engineers and scientists alike. Tools to not only automate, visualize and compute otherwise intractable problems but to enable augmentations of our ability to perceive that which is interesting and new -""a virtual version of a process"" [1] prodding us on the pathways of materials and process discovery.IntroductionActually there are many reasons to apply sensors to materials, such as smart or adaptive materials/structures, and new materials synthesis/processing [1], only some of which are motivated by improved product quality and/or productivity. Although U.S. Air Force applications of sensors to materials processing represent but one of many perspectives, hopefully it is a perspective which will engender new ideas and insights in addressing future challenges in materials research. To provide context and establish need for future sensor applications in materials processing, we will utilize on one of several Air Force vistas or '21st-Century' objectives."

Jan 1, 1997

By K. Fuenkajorn

Geomechanics and geohydrological considerations for the seal design for mine openings are presented. Design guidelines derived from laboratory and in-situ experiments are proposed. The results suggest that seal design, specifications and material selection should be site-specific. Performance requirements for a specific seal location should be identified. Evaluation of sealing effectiveness should be made on the entire seal system, i.e. seal, seal-rock interface, excavation-induced damage zone and the surrounding rock.

Jan 1, 1997

By George P. Schivley

When drilling blast holes, with roller cone bits, a phenomenon known as drilling vibration can occur. It is characterized by either axial or lateral modes of periodic motion of the drill pipe; superimposed on the time-average angular motion of the drill pipe provided by the drill rig rotary head and the vertical motion associated with the penetration rate of the tricone bit into the rock being drilled. This periodic motion can be very severe and, if appropriate action is not initiated by the drill rig operator, could lead to structural damage to the drill rig. Ultimately, the occurrence of drilling vibration limits the productivity potential of a rotary drill.

Jan 1, 1997

By S. J. Bluhm

INTRODUCTION Lesotho is a mountainous area of southern Africa from which water is to be exported in an extensive tunnel system, to industrial regions inland. The related tunnelling project has involved a num- ber of drives using tunnel boring machines [TBMs] to excavate about 100 km of 5 m diameter water tunnels [von Glehn and Bluhm, 1995). This paper describes the ventilation and cooling of some of the tunnel drives from both the operational and design points-of-view with a particular focus on heat generation. There were many common features in all of the drives but this paper is focused mainly on the Hlotse drive which was 18,4 km long. The drives were ventilated using forced ventilation systems to provide appropriate air flow throughout the tunnels and face zones. In addition, the Hlotse drive required refrigeration equip- ment which provided chilled water to the tunnel. While the sec- ondary ventilation systems play an important role in gas and dust handling, the paper concentrates on the primary ventilation and cooling issues. The ventilation of these tunnels was an exacting exercise be- cause: • Rock temperatures and geothermal heat flow were high. • TBMs with relatively high power ratings were used. • Diesel locomotives were used. • Drives were relatively long. • High altitude meant a low air density. An important feature was the simulation and monitoring of the ventilation and heat flow components and the project was characterised by analysis, monitoring and ongoing tactical decision-making throughout the progress. The thermodynamics of the systems were complex because there were many interactive effects and analyses were carried out using special computer pro- grams. The monitoring confirmed the accuracy of the models, and in this manner it was possible to confidently ensure healthy and safe working conditions and still minimise costs. Local ambient climate conditions range from temperatures higher than 35 "C in summer to below -10 OC in winter. Based on available statistical data and the thermal storage/damping effects in the system, design summer ambient conditions were taken as 15 OC/25 "C wet-bulb/dry-bulb. The barometric pressure was 80 kPa and due to the altitude, the ambient air density was only 0,9 kg/m3. The local Authority specified a maximum in-tunnel wet- bulb temperature [at any point] of 32,O OC and a mean wet-bulb temperature [from all locations] of 27,5 OC maximum. The maxi- mum height of ground cover above the tunnel was 1 200 m and the maximum virgin rock temperature was 41 OC; see Figure 1. Diesel dilution criteria specified by the local Authority was a minimum of 0.1 m3/s per rated kW of diesel engine. Other requirements related to gases such as CO, CO2, NOx and CH4 [and the need for intrinsically safe equipment] but these are not of direct relevance to this paper. The actual average face advance was about 30 m/d with good days achieving 60 m/d and good months achieving 1 000 m [23 working days]. The original design tunnelling rate was 50 m/d. DESCRIPTION OF HLOTSE DRIVE VENTILATION AND COOLING SYSTEM The ventilation requirements in the tunnels were dictated by heat and diesel dilution needs. The best ventilation and cooling policy is generally a balance between using increased quantities of fresh air or refrigeration [or both]. In this particular scenario it turned out that, since the diesel emission criteria required large quantities of air, the refrigeration needs were modest. The drive was ventilated using a ducted, forced ventilation system from fans located at the portal. The maximum ventilation requirement was 51 m3/s when the drive was at 18.4 km. From a heat flow point of view, the worst scenario was a heat load of 3.5 MW when the drive was at 7 km. This was cooled by the ventilation air and a supply of chilled water to the tunnel. Refrigeration and chilled water system In the design phase, a detailed comparison was carried out between two general alternatives for providing refrigeration. First, was a system in which refrigeration sets and air coolers are installed on the TBM train; the refrigeration sets are cooled by condenser water piped to and from cooling towers at the portal. Second, was a system in which refrigeration water chillers are in- stalled at the portal and chilled water is piped into the tunnel. The detailed comparison indicated that the capital and running costs of the second system were at least 60 % lower than the in-tunnel plant. There were also many obvious practical benefits for favouring the portal system. The refrigeration plant supplied 23 11s of cold water at a temperature of 10 OC. After providing the cooling effect in the drive, the water returned to the portal where it was initially cooled in open-circuit evaporative pre-cooling towers, chilled in the refrigeration plant and then returned to the tunnel. The cold water flowed into the tunnel in an insulated supply pipe and returned in an uninsulated pipe; the water was simply circulated to the end of the pipe and returned. The cooling effect in the tunnel was achieved entirely through heat transfer from the pipe [long linear heat exchanger] and no air coils or other heat exchangers were required. The cooling requirements were satisfied by the heat transfer to the returns chilled water steel pipe [200 mm]. The pipes were eventually installed to a maximum distance of 10,8 km in what was considered a very practical and cost effective solution.

Jan 1, 1997

By K. J. Shoop

This study investigates the use of a horizontally-baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Jan 1, 1997

By J. S. Hayden

It is becoming increasingly difficult to secure local aggregate resources that meet quality standards and local restrictions without conflicts with other land uses and environmental regulations. The successful integration of natural-resource information into land-use decisions is becoming increasingly important as the needs for both land and resources become more numerous, complex and urgent. Well-reasoned decisions about land-use are crucial to the Nation if infrastructure resources are to remain economically available. Provisions for uninterrupted future supplies of aggregate should be made using proper long-range planning that incorporate a multiple land-use program. That program would include identification and protection of natural resources, strategies that will permit development of resources according to future market needs and environmental considerations, and the beneficial reclamation of mined-out areas.

Jan 1, 1997

By R. L. Grayson

Using powerful database management software, nested-field analysis and microanalysis of narratives have been made of West Virginia accident data, resulting in a new approach for targeting and prioritizing safety interventions by county, mine size, specific mine, job title, type injury, etc. and combinations of these parameters. The analyses have been useful in focusing training and discussion sessions on specific work problems, trends, conditions, and situations for targeted groups of miners. Application of the technique will be presented in this paper, along with comparisons of various mine performance measures.

Jan 1, 1997

By Thomas R

The successful `marriage' between a company seeking to raise funds to develop a project and their financiers calls for a strong mutual understanding of each other's needs. For a company attempting to raise funding, the alternative methods are ever expanding. The optimum method will vary depending on the financial position, risk/reward outlook of the company and the strength of the project for which development capital is being sought. It is likely that small mining companies will need to raise equity funds for advancing projects to the development stage. At that time, they will probably still require a reasonable level of shareholder equity to meet the requirements of banks and other parties to cover potential cost over-runs on the project and feasibility costs. Larger companies, however, are likely to find it much easier and cheaper to raise debt from banks. When evaluating companies and projects for funding, banks will pay particular attention to the quality and experience of management in developing similar projects and it may be necessary for some companies to retain the services of outside consultants. Before a project needs funding, companies should meet with potential financiers to develop relationships to select and ensure a smooth transaction to funding in the future.

Jan 1, 1997

By Lee W. Saperstein

The SME Research Council assists SME and its constituencies in establishing research directions that will benefit the mining industry and its professions. It also provides information about these directions to its membership, to government and to related industrial societies. The 1995 Research Forum, organized and chaired by George Luxbacher, was the second in a series of meetings organized to develop these directions. A copy of the full proceedings is available from SME for $12 plus postage and handling. The first research forum (Saperstein, L., 1993, "Technology for the Future, MINING ENGINEERING, Vol. 45, No 11, November, pp. 1382-85) invited mining industry representatives to discuss the unsolved technical problems that were keeping the industry from greater economic and environmental efficiency. The second forum asked academic researchers to discuss the same general topics from their perspective. It came as no surprise that, in general, the two sets of presenters tackled the same problems. There was no surprise when the academics spoke of the need for fundamental long-term research. What may have been surprising was the number of university people who spoke for near-term research that leads to measurable economic returns or savings. The closure of the US Bureau of Mines (USBM) has changed the objectives and attitudes of the SME Research Council. From being a point of liaison between SME and USBM - a conduit of items from each party to the other the council is now much more on its own. This isolation presents opportunities and hazards. The opportunities are exciting because the council could be the focus for mineral industry research policy if it were properly structured. The hazard is obvious - if there is no bureau, it could be argued, why maintain the council? Many people believe that SME should take the first course and become the beacon for research policy. More than ever, money is being spent on minerals industry research by the federal and state governments - particularly at the mineral-oriented land-grant universities - by industry and by consortia among these groups. SME could be at the hub of these programs. There is a general concern that industry is less able to maintain an economic edge by means of geologic discovery. According to Titley, there will be fewer major, new world-class discoveries except, possibly, at the continental and tectonic-plate margins. Consequently, economic advantage will go to those companies and nations that stay ahead technologically. Given the inevitable diffusion of technology, it can be concluded that technology development, underpinned by research, must be continuous to maintain profits. This is a change from earlier years when change would occur in relatively rare major steps that were interspersed with extended periods of technological equilibrium. Over the fiscal years 1994 to 1997, there has been a 24% cut in research spending by the Department of the Interior (figures from the American Association for the Advancement of Science). This is the largest budgeted percentage cut in research funding of any federal department. Even so, there is still a substantial amount of federal research funding expended in the mineral and extractive-energy industries. The US Geological Survey, Environmental Protection Agency, Departments of Defense and Energy and others expend substantial funds on minerals industry research. Industry - producers and manufacturers - is also spending large sums on research and research-like activities. This activity argues that there is a role for SME's Research Council. Providing focus Consortia. The closure of USBM has resulted in the migration of expertise to consulting firms and to other entreprenrutisl research entities. Many of these groups are creating ad hoc consortia among themselves, nearby universities and industrial partners. The Research Council is well placed to provide an open forum for these con¬sortia. Presentations of research results, as went on in the annual meetings of the Generic Mineral Technology Centers, can help to establish an. archive of results and an avoidance of duplication of research. A continuing sense of research directions can evolve. National Science Foundation. No discussion of consortia would be complete without mention. of the National Science Foundation's (NSF) programs for Industry/University Cooperative Research Centers (IUCRC) and Grant Opportunities for Academic Liaison with Industry (GOALI). NSF is aware of the gap in federal support of science and technology caused by USBM's closure.

Jan 1, 1997

By Jamal Rostami

With the recent technological advances; Tunnel Boring Machines (TBM) have become a viable economic alternative to drill and blast in hard rock excavation. These machines are finding increasing use in underground mine development due to the potential benefits they offer. The successful application of TBM technology to mining depends on the selection of the most suitable equipment and cutting tools for the rock and ground conditions to be encountered. In addition to required testing and geotechnical investigations, cutterhead design optimization is an integral part of the machine selection to assure a successful application of the machines in a specific project. This paper presents and discusses the back-ground of TBM application in a mining environment and the lessons learned, the process of conducting site investigation and the necessary laboratory testing together with machine selection and performance estimation for TBM use III mine development.

Jan 1, 1997

By Jun Yuan

Kaolin clays from five different commercial deposits in Georgia were studied to understand the variations of zeta potential and related fundamental properties. The results suggest that higher negative zeta potential is related to exchangeable or soluble calcium ions in the clays.

Jan 1, 1997

By R. Winand, M. Degrez, C. Temmerman

"The influence of the copper electro crystallization inhibitors (mainly thiourea, gelatin and chloride ions) is studied in a new fully automatic pilot plan. This paper describes the conception and the building of this plan. The new approach is to reproduce the experimental conditions observed in the industry with the three additives present simultaneously in the electrolyte and secondly to study the influence of a slight modification of the concentration of one inhibitor, the others being present in the electrolyte with their industrial nominalconcentrations.1. INTRODUCTIONDespite the fact that gelatine, thiourea and chloride ions have been used in copper electrorefining for a long time, precise knowledge concerning their influence on the cathode deposit, metallographic structure and associated properties is still lacking.Many authors studied the influence of each additive separately, or of two added at a time. Only a few authors studied the combined influence of the three additives added simultaneously. The general conclusion that can be drawn is that the combined influence is far from that forseen from the influence of each additive separately, or even from two additives used at a time. Moreover most of the experiments described in the literature were performed by adding all additives at once initially. It is however, well known that gelatine looses a great part of its activity during the first half hour due to degradation by sulfuric acid (as shown by the cathode overpotential drop). Thiourea is rapidly replaced by a number of degradation mole,cules and complex ions including cations from the solution, changing even the equilibrium between Cu, Cu(I) and Cu(II).Chloride ions are consumed by precipitation.A number of successive research projects [1-9] led pregressively to the concept that, in order to obtain reproducible results representative of industrial cathodes, it was necessary to simulate as far as possible industrial conditions. It was essential that all additives were added continuously during the electrolysis, with, as consequence, a continuous bleed.The purpose of this paper is to describe the concept of a new fully automatic pilot plan for copper electrorefining and to present the first results."

Jan 1, 1997