Search Documents

By X. Nie

A new one-step process was developed to completely eliminate iron and directly obtain pure Ni, Co, and Cu chloride catholyte from nickel rich matte by low temperature (400 0c) chlorination roasting of Ni, Co, and Cu with HCl and leaching with water (PH 7). The effects of roasting temperature, time, oxygen potential and HCI addition and leaching temperature, pH, H2S04 addition and residue sulphur on the recovery of metals and purity of leaching solution were investigated. More than 99 % of Ni and Co and 95 % of Cu in the matte was directly extracted into the solution while 99.995 % of Fe remained in the residue. The iron concentration in the leaching solution was less than 3.6 X 10-5 mol/L.

Jan 1, 1994

By J. W. A. Morris

To investigate the use of centrifugal fields in fused salt electrowinning cells, a high temperature rig has been designed, constructed and commissioned. Initially, the cell has been applied to the fused salt electrowinning of zinc. Current efficiencies of 93% have been obtained for inter electrode gaps as small as 8mm for 70mm diameter electrodes rotating at 100rpm. The construction of a semi-rigorous physical model has shown the potential exists to extend the use of centrifugal fields to the electrowinning of light metals.

Jan 1, 1994

Actual observations of rockburst damage, together with some theoretical considerations, strongly suggest that conventional approaches to the design of tunnel support are inappropriate where there is a significant seismic risk. The present widely used support systems, which are based on stiff, fully grouted re-bars, are inadequate where rock displacement velocities exceed 1 m/s. It is shown by means of a simple conceptual model that yielding of the support elements is essential to ensure their survival when they are subject to the high strain rates typical of severe rockbursts. The model proposes that the total load in the element is an impulsive tensile force imposed and sustained by a single 'tributary' block ejected from the tunnel wall. The stability of the system is determined from a comparison of the kinetic energy developed by the block with the energy of deformation absorbed by a grouted steel tendon. A novel test procedure was developed for the validation of this approach, and for an examination of the energy-absorbing capacity of stiff and yielding tendons. The results of an initial series of tests showed that the recently developed cone-bolt is an effective yielding device. It absorbs twenty times more impulsive-load energy than is consumed by the complete fracture of grouted re-bar of equivalent strength, and it remains totally unscathed. Importantly, the results demonstrate that the ejection model is not merely an explanatory concept, but can be used as a representative and valid design method.

Jan 1, 1994

By L. Xu, R. Bhaskar

The trends in dust exposure levels and longwall production over the last 20 years were examined. The study was conducted for nine major underground coal mining states: Alabama, Colorado, Illinois, Kentucky, Ohio. Pennsylvania, Utah, Virginia and West Virginia. The dust exposure and shift production data were obtained from the Mine Safety and Health Administration (MSHA). Trends were identified and analyzed for the headgate, tailgate, jack setter and shearer operator positions. The relationships between average scam height and dust exposure levels as well as the percentage of dust samples exceeding the dust standard for the four occupations were examined. The concentration to production ratio, a better indicator of the success of dust control measures, was calculated for the 20-Year period. The data show that, in general, dust exposures over the last two decades hare decreased. However, it appears that much of the decrease was in states that had significantly high dust exposure levels (such as Alabama and Utah), while for states such as Virginia, West Virginia and Pennsylvania, the decrease was not as dramatic. Major reductions were made in the period starting in 1982, when a host of longwall dust control techniques was introduced. However, nearly 35% of jack setter and shearer operator dust exposures were still above 2 mg/m3 in 1990, with nearly 20% of tailgate operator exposures and 8% of headgate operator exposures being above the federal standard. The concentration/production ratio has shown a remarkable decrease since 1981. This indicates that long wall operators have been able to meet increased production as well as, to a large extent, control chest production at the face. An analysis of the relationship between average seam height and dust concentration for the years 1984 and 1990 shows that while in 1984, the dust concentration could be correlated to seam height, in 1990 the relationship was less definitive. This indicates that technological factors may be more important than seam height.

Jan 1, 1994

By Karan S. Keith, Haydn H. Murray

The sorptive and impervious nature of clay materials was recognized long before modem technology allowed us to understand the physiochemistry of clays. In Cyprus, around 5000 BC, sorbent clays were used for fulling woolen cloth. One of the earliest recorded uses of clays as an impervious liner was more than 3200 years ago in the construction of a bitumen-sand-gravel-clay liner built along the embankment of the Tigris River at Assur. Today one of the most common applications for clay minerals in the environmental industry is for use as impermeable barriers to fluid transport. Clay minerals are fine in particle size and thus have large surface areas, which, as a result of intermolecular forces and ionic substitutions, make them excellent materials for both ion exchange and ion sorption. Therefore it was logical to consider certain clay materials for applications in the environmental industry, where they can act as physical and chemical traps for potential contaminants. Certain bentonites have historically been used as sealants for fluids (Grim, 1962), and other clays have been used as sorbents for both water and oil (Haden, Jr., 1972). Prior to the 1980s, disposal of the nation's municipal, commercial, chemical, and nuclear wastes was largely indiscriminate and poorly regulated. This created environmental pollution problems, especially with respect to groundwater contamination. Promulgation of federal regulations like the Resource Conservation and Recovery Act (RCRA) and the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA - commonly known as Superfund) have forced a more careful and costly approach to waste disposal. The US Environmental Protection Agency (EPA) is the government body charged with enforcing and ensuring compliance with federal regulations governing toxic waste production, storage, and disposal. Widespread application of geotechnology to the design and construction of waste containment systems and to pollution remediation has become necessary due to such laws and because of increasing use of the subsurface environment for the disposal of hazardous wastes. In the United States nearly 1.8 kg of trash is disposed of per person per day, which amounts to nearly 181 Mt per year. This amount is more than double the waste produced in 1960, and these numbers are expected to continue to increase. Canada produces approximately 1.68 kg of waste per person per day. The EPA estimates that in the United States 64% of our garbage is landfilled, 18% recycled, and 18% incinerated. Even with continued increases in recycling and incineration efforts, the EPA projects that the United States will still need 82% of today's landfill capacity in the year 2000. Data on the exact number of landfills in the United States and Canada is conflicting in part because of changing definitions of what constitutes a landfill and because of inadequate record- keeping by some states and provinces. An estimate of the number of municipal solid waste (MSW) landfills in the United States in 1990 to 1991 ranged from 4 462 to 10 467 with an average estimate of 6 600. In Canada the number of MSW landfills reported varied from 5 493 in a 1982 survey to 1 766 reported in a 1991 National Solid Wastes Management Association (NSWMA) survey (Repa and Sheets, 1992b). A properly operated MSW landfill on average requires 1 hectare of land per year per 25 000 people (Coates, 198 1). In addition to MSW facilities, there are also waste disposal facilities needed for hazardous waste and low level and high level radioactive waste. In 1983, approximately 266 Mt of hazardous waste was generated in the United States, almost 50% of this by industrial production. About 68% of the hazardous waste generated in the United States and Canada and almost 50% generated in Europe are still landfilled (Egger, 1987). In 1985, approximately 51 000 m3 of commercially produced low level radioactive waste was disposed of in radioactive waste disposal sites across the United States (Jungling and Greeves, 1989). By 1987, the US defense program had produced approximately 10 000 t of high level nuclear waste. In addition, there were approximately 14 000 t of spent fuel assemblies from commercial nuclear power plants in temporary storage; the amount is expected to nearly triple by the year 2000. Presently most commercial spent fuel assemblies are stored in water-filled pools at nuclear power plants. Defense waste is stored on federal reservations in surface and underground steel tanks (Anon., 1987). Under federal law nearly all waste disposal and containment sites are required to have a liner or barrier and a cover system design that meets federal- or state-approved hydraulic conductivity requirements for the type of waste that the site will receive. When approved materials, necessary for constructing the waste containment structure, are not available on site, one of the most economical ways to meet these requirements is through the use of clay, soil/clay, or clay/geotextile materials. In a 1991 survey by NSWMA of its members and other select private sector facilities, 81% of the surveyed landfills had some type of liner system. About 75% of these liners were clay materials (either recompacted or natural). The remaining 30% were using flexible membrane liners as part of a liner system. Clay liner materials are most commonly used in the South, Midwest, West-central, and South-central regions of the United States. About 93% of the landfill facilities had closure plans, and of these 91 % were using clay materials in some way for the final cover material (Repa and Sheets, 1992a). Waste barriers and containment structures take several basic forms, and they are used in a variety of different applications: 1) cutoff walls, 2) soil or soil/clay-admix liners, 3) geosynthetic bentonite-clay/geotextile membranes, 4) radioactive waste containment barriers, and 5) synthetic geomembranes. This chapter will discuss the first four of these categories. The field of synthetic geomembranes, although a related topic, is beyond the scope of

Jan 1, 1994

By A. D. Davis

The disposal of spent ore from cyanide heap-leach processing facilities is of concern to the mining industry, regulatory agencies, and the public. Disposal of several hundred million tons of additional spent ore is planned in the western United States during the next decade, with increased amounts likely if gold prices rise. In the past decade, more than fifteen million tons of spent ore have been disposed of in the Black Hills. South Dakota's off-loading criterion for cyanide has been set by the state's Department of Environment and Natural Resources at 0.5 parts per million (ppm) as weak acid dissociable (WAD) cyanide. Nitrate off-loading limits vary for each mine in the state, depending on ore type and other factors. Nitrate concentrations in leachate from spent ore depositories could be caused by conversion from other nitrogen-containing species. One likely source of nitrate is residual explosives from blasting of ore. Previous work on the combustion products of nitrogen explosives has shown incomplete 3xidation (Johansson and Persson, 1970). Another likely nitrate source is degradation of cyanide to ammonia, followed by oxidation to nitrite and nitrate.

Jan 1, 1994

By L. F. Delgado

Environmental and cost pressures sparked renewed interest in gravity separation. Industrial sands in Mexico are generally processed by screening, desliming, and flotation. Gravity separation with spirals was evaluated as an alternative to flotation in order to lower operating costs and decrease water pollution. Outstanding operating results are obtained in glass and foundry sand operations, plus a more competitive position for Mexican producers due to lower operating costs. Coal fines, generally recovered by flotation, have the same cost and environmental advantages when processed with spirals.

Jan 1, 1994

By Andre Vien, D. H. Hendriks, D. Willet, B. C. Flintoff

"For many years the training of mill operators was an informal process which involved senior operators training junior operators on an as-needed basis. Recognizing the needs and benefits of better training some companies, and even some provinces through legislation, have moved to ensure that a formalized training program exists in the plants. These programs tend to focus on basic safety and operations. Much remains to be done. With the more rapid incorporation of new processing and information technologies, and the goal to keep labour costs to a minimum by doing more with less, operator training has become a critical issue. This paper briefly examines the evolution of training programs, provides some measure of their effectiveness, and explores some recent developments which could have a very significant impact on the industry.PreambleOne can draw an analogy between operator training and the mechanical support of production equipment. When we buy a piece of process equipment it is critical that the mechanical installation be done properly to ensure that the device will operate at peak performance on start-up. Once the equipment is running, some form of preventive maintenance is required to ensure continued efficient operation. The operators and the equipment are both elements of the processing system, yet the former do not seem to get the same ""start-up"" or ""operating"" support. Are they not seen as critical to efficient operation? Why is this so? What impact does it have? How can we improve?These are all very logical and important questions, although the answers are not nearly so obvious. In the mineral processing industry, progress in operator training over the past thirty years has been limited and quite variable. To address the perceived need for a more coherent and consistent approach, some provinces have moved to incorporate basic training requirements in their legislation. Some plants have gone a few steps further by building integrated training programs into their operating culture. One conclusion which can be easily reached is that there are no standards, and that the range of training activity is great. In other words, a flotation operator is not a flotation operator is not a flotation operator. Their knowledge and skills are very much a function of training and experience, which are clearly corporate and site specific."

Jan 1, 1994

By John J. J. Chen, Barry J. Welch

"As in many industrial processes, the detailed mechanisms involved must first be understood before being able to redesign, or to carry out improvements or optimisation of the process and equipment performance. In a great majority of metallurgical processes, visual observation and actual measurement of process variables are either very difficult or near impossible. Often, the cost and effort involved are prohibitive. Consequently, physical modelling is often used to provide some understanding of the process and for the validation of computer numerical models. In this paper, we summarise some of the work carried out at The University of Auckland on the modelling of the Hall-Héroult electrolytic cell, the in-line melt treatment process, and the steel casting tundish. IntroductionIn any industrial process, it is essential to understand the underlying mechanisms before any optimization or process improvement can be carried out. In many metallurgical operations, the processes are conducted at elevated temperature and under rather hostile environments. Consequently, it is often difficult, and sometimes impossible, to observe the actual processes occurring, or conduct measurements which are pertinent. In some situations, it is possible to formulate mathematical equations purported to describe the process, and obtain the solutions numerically. However, in this latter case, the validity of the simplifying assumptions made are often uncertain. Physical modelling may provide the necessary information for the validation of such numerical models. Furthermore, through an application of the principle of similitude, it is possible to apply data obtained from physical modelling to actual metallurgical processes. This paper will summarise some the work carried out at The University of Auckland on the physical modelling of gas-induced flow in the Hall-Héroult electrolytic cell, an in-line melt treatment unit, and the flow in a steel casting tundish.Gas-Induced Flows in a Hall-Héroult CellIn an aluminium cell, the effects due to electro-magnetic forces have been addressed and various design modifications such as magnetic shielding and the positioning of risers have been carried out to control or lninimise the effects of magnetic fields'. Consequently, the effects of gas-induced flows are now becoming significant providing the impetus for the study of the gas behaviour in the bath. Furthermore, the shape and size, and the rate of evacuation of the anodically generated gases affect the cell voltage affecting the energy efficiency; at the same time, the back-reaction between the anode gas and the metal produced is the predominant cause of the loss of current efficiency. Figure 1 shows a cross-section of a conventional cell in which the gas evolution occurs directly under the anodes, and the gas induced flow is confined mainly to the region occupied by the bath"

Jan 1, 1994

By C. L. Kusik

Environmental issues are having a significant impact on how automobiles are designed and ultimately disposed of at the end of their lives. On one hand, increasing concerns about landfill disposal have resulted in greater attention being focused on recycling materials and components from old junk autos. On the other hand, corporate average fuel economy (CAFE) requirements have led to downsizing, use of coatings, materials substitution and other measures that often make recycling more difficult. Automobile makers have responded to Corporate Average Fuel Economy (CAFE) Standards in a variety of ways such as: Downsizing; Designing of more fuel efficient engines; Reducing aerodynamic drag by sleeker body designs; Redesigning by using thinner gauges of coated steels; and Substituting material such as lightweight plastic or aluminum parts for steel. Other driving forces affecting production techniques, choice of materials and recycling issues include the Clean Air Act and its amendments, RCRA. and other environmental legislation. The variety of materials used in automobiles makes the recycling issue extremely complex. Not only does one have different materials used in different automobiles for making similar parts, but changing designs, evolving environmental issues, landfill closures affecting solid waste disposal, and increasing raw material quality standards have created a complex set of dependencies related to materials use and recycling.

Jan 1, 1994

By S. Banisi, J. A. Finch, A. R. Laplante

"A technique for on-line simultaneous estimation of gas and solids holdup (volume fraction), based on a combination of conductivity and pressure difference measurements, is proposed and tested in a laboratory flotation column (10cm in diameter and 447cm in height). Fundamental concepts underlying this technique and the effect of relevant parameters are discussed. In the studied range, 3-30 %v/v gas holdup and 2-18 % v/v solids holdup, experimental results showed good agreement between the estimated and actual holdup values (as determined by an isolating technique). The relative accuracy of the solids holdup estimation increased when solids density or solids concentration increased. Frequent re-calibration of pressure transducers was found necessary for accurate phase holdup estimation.IntroductionGas holdup is a key parameter in controlling the performance of flotation columns. For example, flotation rate is affected by bubble size and gas rate both of which, in turn, affect gas holdup. Moreover, gas holdup also determines the slurry residence time which indicates a direct influence of gas holdup on recovery.Gas holdup determination has been the focus of many studies (e.g., Castillejos, 1986; Marchese et al., 1992). Some of the techniques which have been used are given in Table 1."

Jan 1, 1994

By W. K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating the electrochemistry of mineral flotation. A significant need in this area is greater reliability of sensors. The USBM is testing electrolytic methods to clean and condition redox-sensing electrodes to improve the reliability and extend the service life of these instruments in the harsh physical and chemical environment of mineral processing slurries. A novel method for removing scale from fouled electrodes has been developed that includes anodic polarization to 1.2 V versus the Ag/AgCl reference potential, followed by brief potentiodynamic conditioning. Laboratory results show that this technique removes calcarious deposits from gold sensing electrodes and returns the electrode to useful service within approximately 10 min. Mechanical abrasion to remove the scale is thereby avoided.

Jan 1, 1994

By C. L. Schneider

The problem of predicting the liberation spectra produced by a closed continuous grinding circuit is of fundamental importance for the design, optimization and control of most operations in an ore dressing plant. The only known approach through which such a calculation can be performed is the population balance model equation. The latest and certainly most significant progress made in this area is the solution proposed by King (1990), which requires one textural parameter that can be measured directly from the ore being studied. The main advantage of King's solution is that it does not require the estimation of hundreds of arbitrary parameters that cannot be independently measured, as required by the existing conventional solutions. However, King's solution relies heavily on a knowledge of the detailed internal structure of the Andrews-Milm diagram (Andrews and Mika, 1975). This has never been measured for any ore. The characterization of the internal structure of the Andrews-Mika diagram requires the measurement of the liberation spectra at several progeny sizes produced by the breakage of monosize, monograde particles at several different grades. In this paper, a procedure based on magnetic fluid fractionation for generating seven narrow-size, narrow-grade samples is presented. Each of these samples was then broken into six progeny size classes in an ultrasonic mill. The one-dimensional liberation spectra of each of the 42 progeny and seven parent particle samples were then measured by image analysis. The measured linear-grade distributions are presented in this paper. The calculation of the correspondent volumetric-grade distributions is discussed.

Jan 1, 1994

By A. Burkert, A. E. Hajj

"An information system has been developed for the use of companies considering developing a new mine which may be liable to secondary sulphide ignitions or by existing operations. The system uses the Comdale X expert system to analyze information about a particular mine. The system will indicate whether the mine is likely to experience ignitions and what precautions can be taken to reduce or prevent their occurrence. The advantage of an information system using expert system and artificial intelligence principles is that it can recommend action when there is an incomplete knowledge of all the system parameters. By interrogation of the user it can determine the state of knowledge and react accordingly. It is considered that such systems could be of significant use in mine planning for new and existing properties, especially where operators have limited expertise regarding secondary sulphide ignitions. IntroductionSulphide ignitions occur in the underground mines of several countries, including Australia, Canada, Finland, South Africa and the United States of America (1·3) and there has been a significant increase in their number and severity over the last decade(2.4). The basic causes of such ignitions are not well understood and man incidents are not reported or documented.Sulphide ignitions can pose a serious threat to the health and safety of mine workers and to the cost and efficiency of the mining operation (1-5). Byberg(6) described the three major problems associated with sulphide ignitions as:1. the force of the initial explosion can endanger workers and equipment;2. the intense heat of the ignition's flame front can endanger workers and equipment and may also ignite combustible material resulting in mine fires; and3. the sulphur dioxide produced by the ignition may be of such quantity and concentration to endanger workers, as was tragically demonstrated at Geco. In this incident in October 1985, a worker was killed at a position 2400 metres from the ignition point of a sulphide ignition at Manitouwadge, Ontario."

Jan 1, 1994

By Jiuhua Xu, Shuiku Jia, Weiren Sun

"Abstract -The Jinqingding gold deposit, situated in the east Jiaodong Peninsula of Shandong province, is typical of the pyrite-quartz vein gold deposits in the Muping-Rushan gold belt of China . The gold deposit is controlled by a great NNE fracture zone and is composed of several lenticular orebodies within the fracture zone occurring in the Kunyushan granite massif. The Kunyushan granite massif was formed by the replacement of the Archean Jiaodong group.The main minerals associated with gold are pyrite, chalcopyrite, galena and sphalerite; the gangue minerals are dominated by quartz, sericite, microcline and calcite. The mineralizing event can be divided into four stages: (1) pyrite-quartz; (2) quartz-pyrite; (3) siderite-polymetallic sulfides; and (4) calcite-quartz. Gold occurs mainly as native gold and electrum in stage 1 and stage II. There are some evident differences between pyrite from major stages of gold mineralization and that from minor stages; these include differences in crystal forms, size and composition of fluid inclusions.Wallrock alterations consist of sericitization, silicification, pyritization and potash-feldspar alteration. Five alteration zones can be distinguished from unaltered granite (zone 0) to vein lodes (zone IV). Au and Ag increase rapidly from zone 0 to zone IV, Cu increases continuously, while Pb and Zn increase slowly. R-type geological factor analysis indicates that the Au, Ag, Cu, Pb and Zn bear a close relationship to wallrock alteration."

Jan 1, 1994

By Keith E. Forrester

This paper presents results of laboratory and field optimization of a proprietary processes developed by FESI for the stabilization of heavy metal bearing wastes. The specific waste studies presented within the paper include foundry ash, aluminum sweat furnace ash and a heavy metal contaminated soil. The FESI process chemistry and engineered processes were found to be the most cost efficient demonstrated and available method of stabilizing heavy metals and highly successful in passing regulatory limits.

Jan 1, 1994

By R. Ratnagiri, B. Minaie

"In order to expeditiously produce defect-free metallic components in materials processing applications, the relationship between the process parameters and the product properties needs to be well understood while minimizing the production engineering iterations. To achieve this goal, a realistic mathematical formulation of the process should be carried out and an appropriate numerical modeling of various phenomena occurring in such process should be implemented. The materials processing of transforming the molten material into a finished metallic component involves fluid flow and solidification/melting. In the present paper, a finite element based analysis of the fluid flow ·and solidification/melting phenomena in cavities is presented and the various issues in modeling these phenomena are discussed. These transport phenomena play an important role in determining the final characteristics and material properties of the part by affecting the formation of defects and microstructure. A realistic numerical modeling of these phenomena can significantly reduce the rejection rates during the process and can increase the quality of the final product.IntroductionDuring the intelligent materials processing of various metallic components, it is often required to have a thorough knowledge of the behavior of the transport phenomena involved in this process. This is due in large to the coupling that exists between the transport phenomena and the final material properties of the components produced during materials processing. This interrelationship demands that the pertinent transport phenomena in the form of fluid flow and solidification/melting be studied and predicted accurately. In many materials processing applications, the fluid flow is in the form of either a forced convection free surface flow intended to fill a cavity or a natural convection flow resulting from the gravity when the cavity is filled. In either case, the phase change in the form of solidification/melting is also involved in order to complete the process. However, the thermal history during this phase change has a direct impact on the material properties of the final part and the possible defect formation that may be involved. This thermal history itself is dependent on the nature of the fluid flow during the earlier stages of the process. As such, there is a coupling between the fluid flow, phase change, microstructure, and defect formation in the resulting component. It is therefore necessary to analyze these phenomena in order to find optimum methods to produce good quality parts by minimizing the defects that may be generated. Such an analysis can result in the development of appropriate numerical models for the process that can facilitate the economical and timely manufacturing of various components with high consistency. The present paper discusses the issues related to the transport phenomena encountered during materials processing of components engineered largely by using various combination of convective fluid flow and solidification/melting in cavities."

Jan 1, 1994

By I. F. Walder

Mill tailings from skarn-type base metal deposits were studied in order to ascertain potential element mobility in response to weathering. Hypogene ore minerals are sphalerite, galena, and chalcopyrite, showing minor supergene oxidation to smithsonite, cerussite, and covellite. Gangue minerals are pyrite, pyrrhotite, magnetite, hematite, andradite and grossular gamet, hedenbergite, calcite, ankerite, and quartz. Foremost of the eleven tailing piles studied, the hypogene sulfide minerals show no or only incipient post-mining oxidation. Iron oxides and hydroxides form the main oxidation products in the tailings and are enriched in heavy metals. A distinction between pre-and post-mining oxide phases may be obtained based on petrographic observations which distinguish whole-grain versus partial grain replacement. Zn and Cd do not appear to be enriched in the weathering derived oxidation minerals and will be more easily leached from the tailings than other metals.

Jan 1, 1994

By T. P. Meloy

The packed column flotation cell is an awesome separation device. Virtually unknown and untested, the packed column flotation cell is one of the ten most important developments in mineral processing of the 21st century. Though experimental and industrial data is limited, it is clear that the packed column flotation cell is two to three orders of magnitude better than the conventional flotation cell and one to one and a half orders of magnitude better than the open column flotation cell. With the modern packing taking up less than one percent of the packed column, column blocking does not occur. For a packed column operating 24 hours a day, 365 days a year, the estimated mean time between failures (MTBF) is one hundred thousand hours or roughly twelve years. With no moving parts, lower maintenance costs, lower power consumption and inherent operating stability, the packed column is a powerful separating machine. Because there is little meaningful data for comparing the packed column to the conventional flotation cell and the open column flotation cell, much of the material presented in this paper are guesstimates. They are disinterested guesstimate made by the authors after extensive theoretical work and reviewing the known facts. In the authors' opinion, no available data contradicts the guesstimate. The authors expect that there may be errors as large as three hundred percent. Even three hundred percent errors will not change the conclusions of this paper. The packed column flotation cell is a formidable separating device. To understand the problems of comparing the three types of flotation cells, consider the fact that the three cells may have different modes of separation. One of the authors, Meloy, believes that in the conventional cell, the primary particle separation takes place in the liquor with secondary separation taking place in the froth, while for open column flotation, all the separation takes place in the froth. However, he believes that in the packed column a large part of the separation may take place on the walls of the packing. If this is true, not only is the method of modeling each type of cell different, but the method of particle selection in the cell is different. This means that one type of cell may be better at differentiating between two different types of particles. There is a growing body of literature on open and packed column flotation. Suggested reading: (Clarke et al; Hucko et al; Li; Smith & Warren; and Yang).

Jan 1, 1994

By A. A. Hejja

The effect of composition on electrical conductivity, viscosity and liquidus temperature of the slags was investigated in the temperature range of 1300" to 1450°C. The synthetic slags containing CaO, MgO, SiO,, A1,0, and FeO were similar to those employed in the electric furnace smelting of sulphide Cu-Ni concentrates containing PGM (Platinum Group Metals) from the Merensky Reef of South Africa. FeO and SiO, were found to affect the viscosity and conductivity the most while liquidus temperature depended on MgO content in addition to these. The activation energy for electrical conduction was found to vary from 67 to 159 kJ/mol and that for viscosity from 125 to 209 kJ/mol. Optimization of the slag composition was attempted on the basis of opposite trend of the viscosity-electrical conductivity relationship with slag composition.

Jan 1, 1994