Search Documents

By D. K. Panda

The behavior of single drops with gas evolution at the interface is of interest because this is one of the important reactions that occur in oxygen steelmaking vessels, where a large amount of iron-carbon drops are dispersed in an oxidizing slag. The carbon dissolved in these drops, reacts with the slag to form CO, which is evolved as a gaseous phase. A room- temperature model was used to study the nature of this type of reaction including the effect of various factors such as viscosity and the presence of surface active impurities. Experiments were done for reacting drops over a wide size range to observe various regimes of behavior. Large single drops were levitated in a counter current flow to produce a sufficiently long residence time to allow the study of the various stages in the reaction. The emphasis of this work was to obtain photographic evidence of a high quality to describe all possible modes of behavior, and so a lot of effort was given to developing and perfecting experimental techniques.

Jan 1, 1994

By W. C. Lacy

It is the responsibility of educators to look ahead and prepare young engineers and scientists to cope with industrial and social problems of the future. We are faced with a review of history as well as prophesy of the future. The mining industry exists in a "bubble" with little interaction or communication with the outside. This isolation must be broken down if the industry is to survive in the U.S. and Canada. The ability to communicate with the general public and public officials is essential. Many changes are occurring that will require readjustments in technology and staffing. Aging population will result in raising retirement and increasing available workforce. This may force shorter working weeks to supply additional jobs. Environmental concerns will likely direct more attention not only to these concerns during mining, but to planning for post-mining land usage. Retraining and up-dating educational programs are required to cope with these changes.

Jan 1, 1994

R F Johnston 1 ABSTRACT The possibilities for bacterial leaching of refractory gold ores found in the Central Victorian region of Australia are examined. The behaviour of bacteria, especially 77iobacillus ferroaridans is outlined and the effects of these when they are exposed to pyrite, arsenopyrite and stibnite are examined. The factors which are particular to Central Victoria are outlined and the possibility of adapting a bacterial culture to suit the conditions is discussed. It is concluded that a bacterial leaching system is a feasible proposition and that it could enhance leaching rates and yields.

Jan 1, 1994

Provide a low-cost, low-maintenance method for im¬proving mine water quality on abandoned mine land (AML) sites. Approach A model (figure 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of AML. The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions. Water should be analyzed for pH, dissolved iron (Fe), alkalinity, and hot acidity (using the H2O2 method).

Jan 1, 1994

By L. M. Pruett

The Arizona Legislature is currently in the process of considering mined land reclamation legislation in the 1994 legislative session. A bipartisan legislative study committee has drafted proposed mined land legislation. The committee has attempted to craft legislation that is appropriate for the unique conditions in Arizona. Existing Arizona and federal laws and regulations extensively regulate the environmental performance of mines in the state to protect public health, safety and the environment. The proposed mined land reclamation legislation does not replace or duplicate these statutory provisions relating to environmental protection. Instead, the purpose of the proposed legislation is to provide for the reclamation of land that is being mined and to fill the gap in existing laws by requiring the reclamation of land that currently is being mined or that has been mined since 1986 to provide for future land use. The legislation would require an operator to submit a reclamation plan describing the exploration operations, mining operations, post-mining land use and the proposed reclamation measures for review by a state agency. Financial assurance also would be required in an amount such that a third party could complete the approved reclamation measures. Arizona's mined land reclamation legislation would recognize Arizona's leading role in hard rock mining and emphasize the mining industry's economic importance to Arizona and the nation. Because mining operations necessarily require disturbing the surface of the earth to extract valuable minerals, reclamation requirements would be adapted to different conditions and would vary depending on site-specific conditions and on the commodity being mined. The current proposal does not identify the state agency that will administer the mined land reclamation program and approve reclamation plans, substantial changes to plans, and transfers of reclamation plans to other operators.

Jan 1, 1994

By Jose Luis Lopez Mendez

In May 1992, MEXICANA DE CANANEA, S.A. DE C.V. finalized the life of its Reverberatory Furnace which lasted 16 years. This created the need to prepare the Smelter for the next campaign.

Jan 1, 1994

By Mukesh K. Agarwala

Alloy composite parts were made from powders by Selective Laser Sintering (SLS). SLS is a rapid prototyping process that uses data from CADICAMICAE systems to guide a laser beam and rapidly form 3-D prototype parts from powders without any part specific tooling. In this study, Bronze-Nickel parts made by SLS were studied for their mechanical properties. To make the parts structurally sound, SLS parts were further processed by conventional isothermal sintering, without loss of shape. The resultant densification and mechanical properties were studied and related to microstructures and P/M densification models. These results were then correlated to the SLS processing parameters.

Jan 1, 1994

By T. P. Meloy

Like our wives, the comminution of brittle solids is easy to recognize but difficult to describe. However, describing it we must. Describing the fracture mechanism of brittle solids permits the eventual mathematical quantification of the results, process optimization and control strategies. This paper presents a physical model of brittle solid comminution that explains why the slope of the log-log size distribution curves have a slope of one or less in the smaller particle sizes. To develop the hypothesis, modifications of the Gaudin Meloy physical model are made. In brittle solids, comminution takes place by cracks propagating through the material. These cracks may bifurcate as they move. Cracks may terminate either on the original surface of the material, or on a secondary crack within the material formed earlier in the comminution process.

Jan 1, 1994

The initiation of a panel cave is an extremely important and infrequent event in the life of a large underground caving operation. A new cave was initiated at the Henderson Mine in 1991, 15 years after its first cave had been developed in 1976. The original cave was started after a half billion dollars had been invested in the development of the mine, mill and 23 km haulage system. Many things had changed since 1976, the most significant of these being much lower realizations for molybdenum. In 1976 the high demand for molybdenum and uncertainty of caving characteristics, formed the basis for a very conservative cave initiation sequence with miles of boundary weakening and inspection drifting. In 1991 the highly competitive molybdenum market in conjunction with 15 years of caving experience made for a very different mining climate.

Jan 1, 1994

By Michael K. Watkeys, Charlesworth. E. GUY, Jacobus E. Potgieter, Anhaeusser. Carl R., Roger L. Gibson, Alexander F. M. Kisters

Abstract - Intrusive features of cupriferous noritoids from the deeply eroded Proterozoic granite-gneiss terrane of the Okiep Copper District in South Africa illustrate the emplacement of basic magmas into a mid- to lower-crustal environment. The small, easterly trending intermediate to basic intrusions of the so-called Koperberg Suite display a wide variety of geometries, occurrence and emplacement modes, including dike-, sill- and plug-like bodies. Coeval granulite-facies metamorphism, partial melting and ductile deformation of country rock gneisses during intrusion of the basic magmas led to emplacement and dilation processes of the intrusions which differ significantly from those described for dikes and sills at shallow crustal levels. Regional tectonic stresses are largely negligible due to very low differential stress (?1 - ?3) during deformation and intrusion, which permits emplacement at high angles to the principal compressive stress and which follows favorably inclined structural anisotropies. Dilation of the basic intrusions is largely determined by compositional differences of host rocks and occurs by thermal erosion, i.e., assimilation of wall rock gneisses. Low length-to-width ratios of basic to ultrabasic dikes and predominantly diaper -like outlines of mesocratic bodies are indicative of low viscosity contrasts between the mafic magmas and high-grade metamorphic host-rock gneisses. Buoyancy-controlled ascent of the basic to intermediate intrusions is expressed by a broad compositional zoning of basic bodies with respect to the granite-gneiss stratigraphy. Various intrusion modes within the stratigraphic column of the granite-gneiss sequence reflect a lithological and structural stratification of the seemingly homogeneous granite-gneiss terrane.

Jan 1, 1994

By Charles H. Rawlins

Reported is work done on processing of steel mill effluents in the areas of dewatering and separation. Much of the waste from these operations is in the form of sludges from scrubbers, in which the primary constituent is iron oxide. Recycling of the sludge&apos;s magnetic fraction has become economically attractive in order to reduce the overall volume placed in landfills. The objective of this research is to determine the effectiveness of combining magnetic and cyclonic forces, to recover iron oxide particles from waste water stream, while decreasing the volume to be disposed. Three different size hydrocyclones, operating within the field of a quadripole magnet, were tested using varying feed pulp densities of magnetite, magnetite/dolomite, blast furnace (BF), and basic oxygen furnace (BOF) slurries. In the first three cases, the percentage of magnetics recovered increased to greater than 95%. The limiting operational factors are; high pulp density for small cyclones, which can cause flow blockage within the magnet field, and extremely fine particle sizes (<2 microns), which cannot be recovered. The results indicate this technique can remove virtually all the magnetic particles from some steel effluents to a 40-50% weight percent solids pulp, on an in line continuous basis.

Jan 1, 1994

By Michael W. Oakland

Deer Island is the site of the Massachusetts Water Resources Authority (MWRA) wastewater treatment plant which, when completed in 1999, will serve 43 cities and towns in central eastern Massachusetts. Deer Island is located in the Boston Harbor, as shown on Figure 1. The existing wastewater treatment plant on Deer Island is being upgraded to include secondary treatment to comply with Federal require­ments. The new treatment facilities will process an average of 455 million gallons of sewage per day; total capacity will be about one billion gallons per day. The new treatment facilities will cover virtually the entire island. [ ]

Jan 1, 1994

By Gross A. E, Neville P. C

Over the last decade heap leaching with a cement binder has allowed the economical leaching of low grade gold ores of less than 2 grams/tonne. Despite the continued use of cement as an agglomeration aid, numerous leaching operations continue to experience channelling and blinding problems. This paper describes the development of polymeric agglomeration aids, Extract Ore 9760 and 9960, which when used as a partial cement or lime replacement can result in a higher rate of and/or a higher total gold recovery in plant evaluations. Extract Ore in combination with cement acts to produce a stronger agglomerate which results in reduced fines migration during leaching and helps prevent blinding of the heap. Both of these changes will give a more even flow of cyanide solution throughout the heap and improve solution contact efficiency within the ore. Polymeric agglomeration aid programs are now being used by heap leaching operations in three different countries. A summary of benefits identified at some of these operations are presented in this paper.

Jan 1, 1994

By Tom Medak, Don H. Cranney, G Paul McKay, R Douglas Reid

Explosive initiated afterblast dust explosions can occur in high sulfide ore mines when the flame generated by the detonating explosives ignites the sulfide dust produced from the blast, from previous blasting, or from other mining activities. The dust explosion can be a devastating, self-propagating fireball that will damage or consume any flammable object in its path. Damage to ventilation tubing is a frequent occurrence. These explosions also produce large quantities of sulfur dioxide and other noxious gases that can take several hours to clear from the mine. Thus, these occurrences can result in substantial losses in productivity to the mine.

Jan 1, 1994

By William D. Monaghan

The U.S. Bureau of Mines evaluated a teleoperated continuous mining machine for deep mining in thin-seam applications as low as 1 m. Teleoperation increases the safety of mining machine operators because it removes the operator from the face, an area of immediate hazards to safer outby locations. By using teleoperation, the miner can avoid many including unexpected roof falls that can maim or kill miners instantly, methane and coal dust explosions that can be ignited with just a small spark or flame, adverse health effects from miners breathing coal and silica dust, adverse long-term inner ear damage from loud noise pollution, and other hazards related to heavy mining equipment moving about in confined underground roadways. This report presents the surface evaluation results of a teleoperated control system.

Jan 1, 1994

By R. Singhal

Canada&apos;s coal production is approximately 65.4 million tonnes of which 95 % is produced by surface mining methods mostly from the three Western provinces (British Columbia, Alberta and Saskatchewan). The mines are highly mechanized; productivity gains during the past few years have ranged from 60 -80%. Truck/Shovel methods are common although Saskatchewan lignite is almost exclusively mined by draglines. This paper provides an overview of Canadian Coal mining industry vis a vis surface mining. Emphasis is on application and utilization of mining equipment and associated mining methods.

Jan 1, 1994

By T. F. Tomb

on&apos; January 6, ,1992, the Mine Safety and Health Administration (MSHA) issued an Advanced Notice of Proposed Rule Making (ANPRM) for diesel particulate (DP). The ANPRM identified five areas where the Agency was seeking additional information to assist in the rule making process. These areas were exposure &apos;limits, risk assessment, consideration of other information, sampling and monitoring methods, and feasibility. The period for submitting information relative to the ANPRM closed July 10, 1992. Prior to issuance of the ANPRM, the agency was involved in conducting studies to evaluate sampling and control technologies and to gather information with respect to occupational exposures to diesel particulate in underground mining operations employing diesel-powered equipment. Since issuance of the notice, additional studies have been conducted to provide supplementary information in these specific areas. Results of these additional studies indicate that average DP levels in coal mines not using aftertreatment range from 0.9 to 2.1 mg/m3. Aftertreatment devices can reduce these levels by approximately 50 to 90 percent. Studies conducted in metal and nonmetal mines showed average DP levels ranging from 0.3 to 1.6 mg/m3.

Jan 1, 1994

The absence of coal face particle management practices heavily penalizes coal transportation from initial loading to final consumption. Penalties include dust problems, significantly reduced mine loading cycle productivity, mine belt spillage, excessively high coal preparation costs and chute and dangerous pulverizer blockages at the final point of utilization. The common environmental and economic enemy is fines. Everyone knows that fines cause safety and environmental dust problems, but few understand that fines also swell broken coal to a point where 5 to 15 percent more time and capacity must be used to deliver the same tonnage. In this paper, methods and rewards for reducing and/or managing fines at the mine face are discussed. Computer-based loading cycle model productivity estimates, viewed from a new perspective, are made on the basis of material volume rather than on the long established and frequently misleading basis of tonnage. After all, it is typically the volume of broken material being transported that defines the capacity of a given transportation system, while the corresponding tonnages are merely a reflection of the specific material densities. Published evidence suggests that the swelling of broken coal can be decreased very significantly using small quantities of certain non-frothing chemicals added to mine face spray water and/or by employing improved mine face breakage practices. In a future paper, the effects on transportation productivity beyond the coal mine will be discussed.

Jan 1, 1994

By R. Gong, R. Bhaskar

[Full-scale laboratory experiments were performed to evaluate the effect of ventilation and water spray pressure on the potential dust capture efficiency of a ventilation system comprised of blowing ventilation and an underboon scrubber. The tests were performed for a 1.52-m (5-ft) roof height and 2.36 m-3/s (5000 cfm) blowing ventilation volume, and a 2.44-m (8-ft) roof height and 4.72 m3/s (10.000 cfm) blowing ventilation volume at three face positions of the miner. The scrubber suction rate was varied for the tests to study the effect of scrubber flow rate on capture efficiency. The airflow patterns and scrubber efficiency were determined by performing tracer gas tests. Tracer gas was released through a manifold placed in front of the rotating miner drum. The gas was sampled in a grid fashion using a real-time multi-point gas sampling system. The capture efficiency of the scrubber was evaluated based an the peak gas concentration of the gas laden air drawn through the scrubber and the amount of gas passing, through the scrubber as a fraction of the gas released at the face. The data were analyzed to yield scrubber peak concentrations, potential exposures at various operator locations and the gas removal percentage (GRP). The underboom scrubber appears to work best in the end sump position, relative to the start sump and start slab positions. The capture efficiency scrubber was higher for 2.44-m (8-ft) roof heights compared to 1.52-m (5-ft) roof heights. The data also showed that the scrubber air discharged behind the mining machine may be drawn into the face area by the action of the blowing ventilation system, resulting in recirculation.]

Jan 1, 1994

By A. W. Wensel

The adsorption behavior of sodium oleate on brucite, Mg (OH)2, has been studied by Fourier transform infrared spectroscopy. Both internal reflection and diffuse reflection (DRIFT) methods were used to characterize the adsorbed oleate on brucite. DRIFT measurements were shown to be quantitative, and an equilibrium adsorption isotherm was obtained. The conformational behavior of the adsorbed oleate was investigated as a function of adsorption density. It was found that at sub-monolayer coverage the alkyl chains of the adsorbed oleate had more ?gauche? character than at multi-layer coverages. Also, DRIFT spectra revealed that the adsorbed species were magnesium dioleate. For internal reflection measurements single crystals of MgO were hydrolyzed to form a thin Mg (OH)2 layer.

Jan 1, 1994