Search Documents

By T. M. Barton, M. Gauna, A. A. Campoli

Coal mine bumps, the violent failures of overstressed coal, present a safety hazard to miners when longwall mining is conducted in deep, bump-prone coal mines. Two different longwall gate entry systems were evaluated in a southern Appalachian coal mine located in the Pocahontas No. 3 coalbed under approximately 610 m (2000 ft) of overburden that included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design used a 24.4-m (80 ft) square abutment pillar, while the new design employed a 36.6-m x 54.9-m (120 ft x 180 ft) abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worst-case conditions increased effective bearing area 62%, with only a 9% increase in gate entry system width, and eliminated face bumps that were experienced with the original gate entry design.

Jan 1, 1993

By Chaves AP

This paper describes an investigation on the surface properties and mechanisms involved in the agglomeration of iron ore. For this purpose, an organic binder (carboxyl-methyl-cellulose (CMC)) was used in substitution of bentonite, the classic binder in iron ore concentrate agglomeration. Recently, a renewed interest of the iron ore producers in Brazil to replace bentonite for an organic binder, because of the economy that can be achieved in the, blast furnace operation. These savings are mainly due to the lower aluminum silicate addition which decreases slag volume and the improved pellet metallurgical properties which have the potential for lowering hot-metal production costs. Also organic binders are effective at lower addition levels, which results in lower storage and transportation costs. It is very important in Brazil because of the vast geographical area since transportation is made mainly by truck. Another advantage of organic binders is that they have low ash contents, and therefore most of the binders bum. off during the pellet firing operation. Previous studies have demonstrated the possibilities of the use of CIVIC, but in addition to its high cost, the pellets presented improper behavior at high temperatures or when prepared with high moisture levels. In the investigation here described, these problems have been solved through the addition of other reagents to CMC.

Jan 1, 1993

By D. C. Lynch

While a sizable amount of data exist as to the activity and distribution of minor elements between matte and metal, there has been no unifying theory presented delineating the form of dissolution of these elements in molten sulfides. In order to alleviate that deficiency the literature concerning the behavior of As, Sb, Bi and Pb in mattes is reviewed. Models present in the literature, regarding the thermochemical behavior of minor elements, are tested, and new models are presented and evaluated using thermodynamic theory. The results of those analyses are used to predict optimum conditions for the volatilization of minor elements. The dearth of data on the behavior of minor elements in nickel mattes requires that this review focus on copper- iron mattes. An effort is made, however, to utilize basic knowledge regarding nickel sulfides and the interaction of nickel with the minor elements to predict the behavior of those elements in nickel-copper and nickel-iron mattes.

Jan 1, 1993

By W. E. Lindquist

Roasting of refractory gold ores has the primary goal of oxidizing sulfides and organics to improve gold recoveries prior to leaching. Commercial installations currently utilize bubbling and circulating fluidized beds. The principle of flash roasting is aimed at a more cost effective method of whole ore roasting for large throughput applications. Results of pilot plant testing and scale up to commercial design will be discussed in further detail in this paper.

Jan 1, 1993

By R. McCulloch

Exploration activity in metallic minerals continued to decline in Montana in 1992 as companies either reduced budgets or left the state. The number of active projects dropped another 50% from 1991. Expenditures were 3% to 6% of 1989's 28.6 million. Many of the major mining companies closed offices in Montana. Although depressed commodity prices have hurried the exodus, continuous changes in environmental regulations, as well as the Mining Law of 1872, without regard to economic effect have had the most serious impact. Many companies indicate that Third World countries present a more stable business environment than the United States. Grassroots projects are nearly non-existent, while late-stage programs continue cautiously. Exploration activity continued at the following projects: Garnet, Pegasus Gold; Southern Cross, Asarco; Elkhorn, Goldfields; 7-Up-Pete, Phelps Dodge and Canyon Resources; Miller Mountain, Pegasus Gold; Sheep Creek, Cominco American Resources; Checkerboard, Kennecott and BHP Utah International; Emigrant Creek, Pegasus Gold; and Crevise, American Copper and Nickel. All mineral activity, whether on private, state or federal land, is regulated by the Montana Department of State Lands under three classes of permits - Small Miner Exclusion Statements (SMES), Exploration Licenses and Operating Permits. A total of 230 Exploration Licenses are active in the state with 26 of those being new. However, there are only 433 projects current in Montana, with many of those in the reclaiming stage. The majority of exploration projects consist of individuals expending time rather than money on properties. The number of mines functioning under operating plans declined by one when W.R. Grace closed its Zonolite operation.

Jan 1, 1993

By Trent A. Tempel

In 1989 Newmont Gold company initiated a project to develop a treatment process for higher grade refractory gold ores to be mined from deposits along the Carlin Trend in Nevada. Extensive laboratory and pilot testing have identified a unique whole ore roasting process for oxidizing these ores prior to gold recovery by conventional cyanidation techniques. Subsequent detailed engineering studies by Fluor Daniel evaluated three different dry grinding flowsheets for feed preparation to this roasting circuit. The selected flowsheet will incorporate a two compartment ball mill with an attached drying chamber that is driven by a 11.2 MW (15,000 hp) wrap-around motor.

Jan 1, 1993

By Xia Guangxiang, R. Y. Wan, Yang Hanlin, M. C. Fuerstenau

The mechanism and kinetics of pretreatment on pyritic gold concentrate with the catalytic oxidation acid leach (COAL) process were studied in the temperature range of 80-100°C and oxygen pressure range of 230-1013 kPa, with sodium lignosulfonate (SL) and mixed medium of sulfuric acid (11 g/[ ]) and nitric acid (5.5 g/ [ ]). The results show that nitric acid acts as a catalyst, the surfactant changes the hydro-phobicity of resulting elemental sulfur to favor the oxidation of pyrite, and the oxidation-determining step would be the chemical reaction between nitric acid and pyrite. When about 80% of pyrite contained in the concentrate is oxidized, the gold cyanidation extraction exceeds 95 % . The nitric acid in solution can be recycled and used again.

Jan 1, 1993

By Y. S. Roditis

Traditionally, open pit optimization has been used to produce a single outline which can guide the pit design. This paper describes how a series of optimum nested pits are utilized to: a. produce different mining sequences and to help in mine planning and phase design; b. evaluate different metallurgical processes, production scenarios and equipment size; c. investigate the sensitivity of a project to prices, recoveries, production rates, costs, ultimate pit slopes etc.

Jan 1, 1993

Segregation roasting tests were carried out on Zaire cobalt oxide ores assaying about 2% Co and 3.5 to 6.5% Cu. The major parameters tested during the laboratory investigations were temperature, dosage and type of reducing agent, dosage and type of chloridizing agent, and particle size. Results showed that standard conditions suited to the segregation of copper ores, i.e. low temperature and low dosages of reducing and chloridizing agents, resulted in the segregation of copper only, while conditions suited to the segregation of lateritic nickel, i.e. higher temperature and increased dosages of reducing and chloridizing agents, led to a successful segregation of both copper and cobalt. Under the best conditions, 88% of the cobalt and 98% of the copper could be recovered in a concentrate assaying 32.5% Cu and 8.5% Co. Alternatives to process such a concentrate are briefly reviewed.

Jan 1, 1993

By J. Sharp, R. Arnold, P. Rusin, T. Young, N. A. Sinclair

Many oxide silver and molybdenum deposits remain undeveloped because chemical extraction yields poor recoveries or is environmentally unacceptable. Bioreductive leaching of such ore samples at MBX resulted in high extractions of silver and molybdenum. When baseline, three-day, cyanide bottle-roll tests were conducted on manganiferous-oxide silver ore, 13.7% of the silver was extracted. In contrast, 86% of the silver was microbially solubilized into the organic growth medium by bioreduction with 99.8% dissolution of manganese. A followup cyanide bottle-roll test yielded an additional 8.5 % silver dissolution, for a total extraction of 94.5%. Baseline, three-day, acid bottle-roll tests of the iron-oxide molybdenum ore Yielded 1.8% molybdenum. However, bioreduction solubilized 93.3% of the molybdenum into the growth medium. An additional 0.3% molybdenum was solubilized during the followup acid bottle-roll test. Microbial treatment of refractory oxide ores with bioreductive bacteria resulted in higher extractions of silver and molybdenum than conventional chemical leaching. The bioleaching process occurred at a near-neutral pH at ambient temperatures. The bacterial solubilization of silver and molybdenum was achieved without the use of cyanide or sulfuric acid.

Jan 1, 1993

By David R. Wilburn

The U.S. Bureau of Mines investigated the resources, costs, capacities, market relationships, and short-and long-term supply of bauxite, alumina, and aluminum. The 45 evaluated mines and deposits in 14 market economy countries (MEC's) have a demonstrated resource of 8.4 billion mt of bauxite and an aluminum content of approximately 2.1 billion mt. Developed world bauxite resources and existing primary aluminum smelting and refining capacity are sufficient to satisfy demand through at least 1995, when additional properties (with higher cost levels) would need to be developed to satisfy future demand levels. It is anticipated that new alumina or aluminum production most likely would occur in developing regions with large bauxite potential, low-cost energy sources, and a close proximity to refining and/or smelting capacity. An increase in aluminum recycling capacity would help meet future demand increases. A series of network model supply analyses was performed for the period 1988 through 2000. Based on announced future production levels and assuming demand grows at the level outlined in the analyses, model results indicate there is sufficient material available to meet demand until 1998, where-upon an aluminum shortfall is projected. Additional analyses investigated the effect of a reduced growth rate of demand and regional production variations in Venezuela on the international aluminum industry.

Jan 1, 1993

By Christopher J. Bise

Volume II of this collection of research reports, entitled "Model Training Program," provides the framework and details for developing a tailored training program for a specific mine based upon documented human-performance deficiencies. To do this, several steps must be followed prior to program implementation: 1) background information must be gathered (database analysis), 2) direct observation of indicated problem areas should be conducted (safety sampling), and 3) separation of those deficiencies to be addressed through training from those which would be better addressed by workplace or equipment redesign (trainability assessment). Once training is determined to be the appropriate strategy for addressing the noted deficiencies, several approaches can be taken, depending upon whether the problem is related to repetitive work procedures in a predictable, a variable, or a dynamic workplace with a substantial amount of interaction between workers, equipment, and the environment. Although this volume and the subsequent seven volumes provide examples of how the training information was field tested using various strategies (for example, loss control, task training, etc.) and techniques (for example, microcomputer-based exercises, lectures, etc.), the ultimate selection of the delivery method is based on cost/benefit analysis. Therefore, the Model Training Program has incorporated a Training Cost Model as a desirable component.

Jan 1, 1993

By Alan R. Buehler

The Bureau of Mines conducted a mineral investigation of the 177,000-acre Secesh study area; most of the area had been proposed as wilderness. Bureau personnel mapped and sampled several hundred mine and prospect workings; 1,715 rock, soil, and placer samples were taken during the investigation. The study area is centered about 25 mi east-northeast of McCall, Idaho, in the Payette National Forest. Five mining districts extend into or are adjacent to the study area. There have been more than 3,000 mining claims located inside the study area, 884 are current. In excess of $17 million (historical value) in placer and lode gold has reportedly been produced from the Warren district alone. The study area contains gold, silver, copper, lead, zinc, tungsten, and antimony. At least six properties that would be in the proposed wilderness contain gold resources; more than 18 million tons averaging 0.038 oz/ton gold have been identified. Additional resources may be located at 4 other localities. The 4th of July mine is currently producing gold/silver/lead ore. Similar resources may be located on at least 3 other properties. Placer samples from the study area contained up to 0.34 oz gold/yd3 ($120/yd3). The samples are representative of relatively small occurrences and do not constitute resources; small quantities of gold may be recovered by recreational placer miners.

Jan 1, 1993

Jan 1, 1993

By Peter A. Bevan

"In massive and semi-massive deposits, it is essential to take samples continuously for specific gravity determination as well as for assays of the various metals of interest. Failure to use specific gravity in mixed deposits of high density contrast will result in incorrect determinations of the average grade.Graphs and linear equations of specific gravity against the grade of one metal are not considered accurate enough in a multi-mineral deposit, but appear to be very satisfactory in a theoretical one-sulphide/gangue mix. Specific gravities based on base-metal values only in massive sulphide deposits will result in underestimating the effect of low grade areas on the average grade and also cause a reduction in the calculated tonnage.IntroductionBy definition, a base-metal assay is the percentage of metal by weight contained in a sample, whether it be a soil or silt sample, a grab, chip or channel sample, or a section of diamond drill core.In those cases where there is a series of contiguous samples, say in diamond-drill core, the average grade may be required of the various assays that are above a desired or required cutoff grade.Internal low grade or waste can be included if the assays one side or the other are used to ""carry"" the lower grade material and the resulting average grade is above the cut-off grade. To determine the average grade, the individual assays are ""weighted"" by multiplying these values by their respective lengths, adding up the cumulative assay times length and dividing by the total length. This method is essentially a weighting by volume, because the core diameter is constant and is common to all the samples being considered for estimating the average grade . If some of the core samples have much higher specific gravities than others, and the specific gravities are not used in the weighting process, the resultant average grade will be over-estimated or underestimated, depending on the grade of the heavier sections. When core assays of approximately the same specific gravity or weight are averaged by length, the error in the weighted estimation of the average grade is negligible."

Jan 1, 1993

By Y. K. Yen, J. D. Miller, C. L. Lin

A PC image-based, on-line coarse particle size analysis system is being developed for the control of crushing and grinding circuits. Initial results had indicated that the system is accurate when tested with irregularly shaped particles which are stationary and do not overlap with each other. Now the system has been successfully tested in the dynamic mode with a moving belt conveyor. On-line size analysis for actual plant operations is discussed and includes: (1) the video system with respect to lighting and data acquisition requirements for a rapidly moving belt and, (2) image sampling, specifically the number of observations needed for accurate sampling and the total time required to perform the calculations for a representative data set.

Jan 1, 1993

By G. Heinrich

Size by size recoveries and pentlandite liberation data from image analysis were used to evaluate plant tests of pentlandite flotation and pentlandite/pyrrhotite middlings flotation from pyrrhotite in a circuit treating low grade magnetic intermediates at the Strathcona Mill. Raising the pH with lime gave improved selectivity for liberated pentlandite but there were major losses of middlings unless the circuit was pulled hard indicating the need for finer regrinding. However, size by size recoveries at the normal regrind showed that, while the pentlandite recovery improved in the finer ranges, the pyrrhotite recovery also increased leading to little selectivity in any size range. A much finer regrind gave greatly improved selectivity in all size classes suggesting that 'surface polishing' as well as liberation effects were being seen. Using liberation data from image analysis of the products, surface polishing accounted for over 99 % of the improvement in selectivity. Unreasonable recoveries of more highly liberated particles were observed for liberation analysis by volume fraction but showed the expected trend in recovery when the analysis was based on surface liberation. The surface liberation data showed that the improved pentlandite recoveries after finer regrinding were to more than 90 % caused by improved liberation with the remainder contributed by surface polishing effects. The practical implications of this work are that i) the comparison of particle grades with product grades allows to estimate the effect of regrinding on co-flotation/entrainment, ii) surface liberation models should be used for evaluating recoverabilities by flotation and iii) regrind circuits may be set up to ensure that all particles go through the mill or that only the coarse fraction is reground depending on the surface scrubbing found to be required.

Jan 1, 1993

By J. M. Mutmansky

Introduction Since the Hardy Cross numerical algorithm was applied to the solution of mine ventilation networks, numerous developments have taken place in ventilation network analysis procedures. The Newton-Raphson method, the linear theory method and the second-order approximation method are three of the additional approaches that have been applied. The efficiency of a ventilation network analysis procedure depends not only on the method of solving the system of equations derived from ventilation networks but also on the method of deriving the equations through selection of the meshes. This paper investigates the impacts of three mesh selection methods on the efficiencies of four ventilation network procedures. The minimum-resistance spanning tree method is the most popular procedure for selecting meshes. The shortest-path method was suggested by Epp and Fowler (1970) for improvement of the Newton-Raphson method. The minimum-resistance-path method is suggested here as the third method of selecting meshes. The effects of these three methods on the Hardy Cross method, the Newton-Raphson method, the linear theory method and the second-order approximation method are analyzed in this paper. These network analysis methods have been summarized in the paper by Kim and Mutmansky (1991). Mesh selection methods A procedure for mine ventilation network solution based on mesh equations typically consists of two steps: • the mesh selection step and • the network solution step. The mesh selection step establishes a set of independent equations to solve the network. The resulting equations are nonlinear. One method of solving nonlinear equations is to linearize the equations and iteratively solve these linear equations. The four analysis methods previously discussed in this paper use this approach. The linear equations required for solution can be written in matrix form as: P•dQ = dF (1) where P is the pseudo-resistance matrix, Q is the quantity matrix, and F is the Jacobian matrix (Kim and Mutmansky, 1991). The efficiency of the solution method depends on the characteristics of the P matrix, which in turn depend on the method of selecting meshes. To understand the impacts of the mesh selection methods on the efficiency of the ventilation network analysis procedures, the characteristics of the P matrix must be understood first. The diagonal elements of the P matrix, m in number, are the sums of the pseudo-resistances of the branches contained in the m meshes necessary for solution. The off-diagonal elements are the sums of the pseudo-resistances of the branches shared by two meshes. For example, P12 (first row, second column element of the P matrix) is the sum of the pseudo-resistances of the branches common to mesh 1 and mesh 2. When solving the system of equations expressed in Eq. (1), three of the iterative procedures (the Newton-Raphson, the linear theory and the second-order approximation methods) use the direct factorization method (Burden and Faires, 1985) on the P matrix. When the direct factorization method is used, the computational efficiency is enhanced by larger diagonal elements and a sparser P matrix. Generally, the sparsity of the P matrix is more important than the size of the diagonal elements. There is no known mathematical method of predicting the efficiency of these procedures, but heuristic methods can be used to study the efficiency. The Hardy Cross algorithm applies the Gauss-Seidel method of splitting the P matrix and applies the Newton-Raphson procedure. The efficiency of the Hardy Cross method depends on the spectral radius of the matrix[[D-L]-1U], where D is the diagonal, L is the lower triangle and U is the upper triangle of the P matrix for the Newton-Raphson method (Ortega, 1972). The smaller the value of the spectral radius, the faster the convergence. As with the other three methods, larger diagonal elements and a sparser matrix aid in faster convergence. With the Hardy Cross method, however, the size of the diagonal elements is more important than the sparsity of the matrix. Remembering that each of the diagonal elements of the P matrix is the sum of the pseudo-resistances of the branches in a mesh and that each off-diagonal element is the sum of the pseudo-resistances of the branches shared by two different meshes, the following strategies can be used: • Avoid having branches with larger resistance values shared by multiple meshes. This increases the size of the diagonal elements and reduces the chance of off-diagonal elements being large.

Jan 1, 1993

By Y. Topkaya, R. E. Johnson, D. Buttinelli, B. R. Palmer, A. Geveci, L. Stoppa, C. Lupi, F. Pochetti

Representative samples of a composite mixture of three typical Cu/Zn complex sulphide ores, namely Black-, Yellow- and Altered-ore, from the Cayeli deposit in Turkey, were used for leaching tests in 2.2 M FeCl3, or 1 M CuC12-2 M NaCl solution in the temperature range from 313 K to 363 K (40O to 90O C), with and without the presence of an organic solvent for elemental sulphur, such as CCl4. The leaching rates of copper and zinc were quite high, as expected, in FeCl3 solution and complete recovery of both metals was obtained at the highest temperature when the solvent was present. However in CuC1, solution, extraction yields of the order of 95% only for Cu and Zn were achieved and the positive effect of the solvent was not clearly shown. The kinetics curves of Cu leaching by FeCl3 indicated a model of reaction rate depending on the particle surface, as in a chemically controlled reaction, in tests with the presence of CCl4. Without the solvent, or in CuCl2 media, the model of the diffusion controlled reaction seemed to prevail. Values of apparent activation energy, in both of the leaching processes, were determined and compared with those reported in literature.

Jan 1, 1993

By K. L. Wiley

In-situ leaching, initiated in 1986 at San manual, was economically developed in 1989. The primary reason for this lag time between startup and viable production was the time required for technical development. The technical development pursued comprised detailed design, development, and implementation of in-situ well construction methods, formulation of suitable well pattern arrays, and the development of extensive hydrogeologic and geochemical knowledge of the mineral deposit. Since 1989, the in-situ leaching program has become a viable and cost effective method to extract copper from the supergene mineralized zone of the San Manuel deposit. The in-situ leaching methods that are currently utilized have been progressively expanded and continually developed and will became the cornerstone of copper production from the San Manuel oxide mineral deposit. This paper presents an overview of the supergene hydrogeology, current design techniques, drilling methods and well completion, pump determination and setting, solution management, and future plans for the increased extraction of copper by in-situ leaching methods at the San Manuel mine.

Jan 1, 1993