Search Documents

By J. L. Parks

Designs, installation procedures, and performance characteristics of martensitic cast steel concaves are reviewed. Longer wear life, fewer pieces to install, and eliminating the need to scarf joints are the principal benefits of using martensitic steel to replace austenitic 12% Mn (Hadfield's) steel, the traditional concave material for large gyratory crushers. Installation procedures that reduce the risk of breakage are described. Operating practices that affect concave performance are also discussed.

Jan 1, 1992

By B. J. Arnold

During the past three years, coal samples covering a range of coal rank, ash content, size consist, grindability, and moisture content have been tested for their flow properties using a triaxial shear tester that measures the unconfined yield strength in a compressed sample of coal. The ratio of this unconfined yield strength to the sample bulk density is part of the equation used by handling system manufacturers to calculate the critical arching or critical ratholing diameter needed to ensure that coal will flow from bunkers or bins. This ratio also serves as an index to compare the flow tested. To test the applicability of the index to predicting problems with coal flow, a series of tests were conducted at CO Inc.'s Coal Quality Development Center (CQDC) in Homer City, Pennsylvania. Tests covering ranges in size consist, moisture content, and ash content were conducted by first filling a small two-ton bin with coal and then emptying the bin at a pre-set discharge rate. The actual discharge rate from the bin under the various conditions tested was measured. Samples of the coal discharging from the bin were collected. One sample was analyzed for ash, moisture, and size consist; another sample was sent to the Iowa state University for trivial shear tests (supplying an index measurement). Actual flowability results from the bin were then compared to the measured index to determine the applicability of the handleability index in actually predicting coal flow problems. This paper describes the correlation between handleability index and bin flow and explains the next stages of the project.

Jan 1, 1992

Tennessee is the largest federal program state in the nation, with 62 active surface and underground coal mines. Tennessee's coal resources lie in 22 coal seams in 22 counties. Twelve seams are being mined at this time. Mining in the northern counties is primarily in steep slope areas in the Cumberland Mountains. The relatively flat terrain associated with the Cumberland Plateau makes area-rnining the most common production method in Tennessee's southern counties. The State of Tennessee gained primacy August 10,1982, when its regulatory program was conditionally approved, subject to the correction of certain deficiencies. On May 16,1984, the Tennessee General Assembly repealed most of the Tennessee Coal Surface Mining Law of 1980, effective October 1, 1984. With this action, withdrawal of the state regulatory program was formalized, and on October 1,1984, the Office of Surface Mining's Knoxville Field Office became the regulatory authority. Tennessee is not eligible to receive funds for an abandoned mine reclamation program because it does not have an approved regulatory program. Accordingly, the Tennessee Abandoned Mine Lands Program does not receive federal AML grants. Since 1984, AML projects have been completed under cooperative agreements between OSM and the state; emergency projects are completed by the Office of Surface Mining.

Jan 1, 1992

By Richard M. Levine

Now that the former Soviet Union has divided into 15 countries, it is necessary to analyze separately the industrial mineral position of each of these countries. Industrial mineral data The former USSR was one of the world's largest producers of industrial minerals and had some of the world's largest reserves. Production and reserve figures, however, must be qualified. Even when these figures were reported by the Soviets, it was not clear that the production figures were for products that would be equally marketable in a competitive market economy. The reserve figures are based on the Soviet system of reserve classification, which is not directly equatable with the US Geological Survey and US Bureau of Mines classifications of economic reserves in market economy countries. The Soviets reserve classification system, in terms of which reserve figures will be given, is based on the reliability of the quantity of the material in place. The Soviet system assigns each occurrence to one of seven categories A, B, C1 and C2 are considered reserves; P1, P2, and P3 are considered resources. Mining in the former Soviet Union was authorized on the basis of the reserves in place in categories A, B and C, which had to be in prescribed ratios. However, the categories A, B and C do not necessarily correspond to Western concepts of material economically exploitable under present market prices with existing technologies.

Jan 1, 1992

By E. M. De Souza

"A scientific testing program, sponsored by the Mining Industry Research Organization of Canada (MIROC), was undertaken on the surface and underground facilities of Inca's Crean Hill Mine to investigate the effectiveness of using dry drilling with a dust control system.The surface test work consisted of the monitoring of advance rates and bit life white a series of 165 mm holes, wet and dry, were drilled at both mine air (0.69MPa) and high pressure air (1.72MPa). The results, based on statistical evaluations of field data, indicated that penetration rates can be increased by an average of 24% when drilling dry with high air pressure and by approximately 27.5% when drilling dry with mine air as compared with wet drilling under the same conditions. Dry drilling also has the effect of reducing button wear by approximately 69% using high pressure air. The underground test work employed a dust collection system developed for use with large diameter holes (165 mm) and high pressure drilling. The testing program has indicated that an average increase in penetration rate of 35% can be achieved when dry drilling in rock (waste) and of 49% when dry drilling in ore with high air pressure. Although preliminary dust monitoring did not indicate any appreciable increase in dust concentration during dry drilling, further dust monitoring is still required.A comparative cost analysis has indicated the potential for reduction in drilling costs when dry drilling is utilized. Further testwork is to be conducted to develop a reliable dust collection system for underground production."

Jan 1, 1992

By N. Agron-Olshina

The application of the QEM*SEM image acquisition and analysis system to the measurement of the mineral matter in coal and the materials in fly ash is described. A new sample mounting technique was developed using iodinated epoxy to provide a backscattered electron contrast between the coal, the mounting medium and the mineral matter. Several comprehensive and detailed species identification programs for silicate minerals and materials were developed to analyse the 1000 count x-ray spectra used for the measurements. Case studies are presented to demonstrate the capabilities of the new technique to distinguish different coals and fly ashes by their mineral and material composition rather than by conventional chemical analysis. Applications of the new technique are aimed at demonstrating that composition and size distributions obtained from OEM*SEM measurements can be used: 1. to characterize coal with respect to combustion problems in power stations, 2. to characterize coal for fine coal cleaning, 3. to characterize fly ashes in relation to problems such as erosion in combustion systems and the ease of precipitability in dust collection facilities, 4. to refine the classification systems used in marketing coal for pulverized fuel firing and fly ashes as a component of cement and building materials.

Jan 1, 1992

By C. J. Lewis

This presentation concerns calcium oxide-better known as high calcium quick lime High calcium quicklime is produced by calcining high calcium limestone, mostly in the many rotary kilns located throughout the United States and Canada. This paper presents suggestions on the handling of lime based on field experience. The subjects covered are chemical analyses, transporta¬tion, lime storage, lime slaking to form a water slurry of calcium hydroxide solids, slurry transportation, slurry viscosity, and scaling of lime slurries. It is hoped that the comments on the foregoing areas will be of use to those designing or operating lime systems.

Jan 1, 1992

By Philip E. J. Green

Two of the cornerstones of total quality management, the use of statistical and problem solving tools, and the involvement of employees, are directly applicable to environmental protection. The reduction in variation decreases the chances of violations and mishaps. Involving employees in minimizing environmental impacts is critical. One mistake, even with the best technology, and your plant can be shut down, customers lost and fines and penalties imposed - your reputation and the environment damaged. Proven strategies for involving employees in environmental protection, and over-coming the frequently strong differences of opinions about what constitutes environmental protection, will be discussed.

Jan 1, 1992

By R. A. Metz, William H. Breeding

The remarks that follow are based substantially on experience covering 45 years, 80% of which has been in placer work, rather than on a review of available literature. Most commercial placers have been deposited by the action of water. The richer and more difficult-to-mine placers are those in the headwater areas where gradients are steepest. The most lucrative placers are generally in intermediate areas where volumes are greater, fewer boulders are present, and gradients are from 3% to 1-1/2%. The higher volume, lower grade placers are in the lower reaches of river systems where gradients are lower. Where gold-bearing rivers have discharged into the sea, wave action can concentrate values on beaches, past and present. Most of the rich, readily accessible placers were mined by our forefathers. Current opportunities exist: (1) in remote areas where infrastructure has been absent in the past, or development has been prohibited by adverse ownership - political or commercial; (2) in deposits that could not be mined by equipment available to our forefathers; (3) in deposits unidentified by our forefathers; (4) where the-price-of-product/cost ratio is substantially better than in earlier years; or (5) a combination of those factors. When I entered the placer business in the late 1930s, and subsequently, a prevailing opinion believed that glacial deposits should be avoided as irregular in mineral content and composition, and unrewarding to explore and develop; yet an operator has been mining a fluvio-glacial deposit profitably for the past 17 years. Rich buried placer channels, often called paleo-channels were worked in the last century, generally by hand methods, and under conditions that would be unacceptable today. Exploration and mining equipment now available make some of these channels attractive targets. Well-known examples are in California and Australia. The formation of a commercial placer requires a source of valuable minerals. Above primary deposits, there may be eluvial deposits formed by the erosion of gangue minerals and the concentration "in situ" of valuable minerals. Down slope from these deposits are the hillside or colluvial deposits, and below them are the alluvial deposits of redeposited material. Most of the great placer fields of the world are the result of several generations of erosion and deposition. Well-known examples are in California and Colombia. Gold is a very resistant and malleable material, and gold placers may extend for 64 or 80 km (40 or 50 miles) along a river system. Platinum is less malleable, but is very resistant to disintegration. Diamonds are extremely hard, and (especially gem diamonds) may be found over great lengths of a river system. Cassiterite is less resistant to disintegration, and tin placers seldom extend over two miles without resupply from an additional source or sources of mineralizaton. Tungsten minerals are generally more friable, and within a few hundred yards of the source disintegrate to the point that they are uneconomical to recover. Rutile, ilmenite and zircon placers generally result from the weathering of massive deposits, and may be encountered over extensive areas; most are fine grained and durable. What does a geologist or mining engineer look for in placer exploration? The old adage to look for a mine near an existing mine is still valid. You need a source of valuable mineral. Then you require conditions for concentration, which means a satisfactory gradient and/or other conditions that will permit heavy minerals to settle. Nicely riffled gravel, often called a shingling of the bars, is conducive to placer formation. Coarser gravel is logically associated with coarser gold. Excessive clay and/or high stream velocities in narrow channels can carry gold far downstream and distribute it uncommercially over a large area. When material is extremely fine, in situ weathering and concentration become more important. Placers frequently occur distant from lode mines, and one must remember that in a larger watershed the exceptional floods that occur once in a hundred or a thousand years can move great quantities of material long distances. The carrying power of water is said to vary with the fifth or sixth power of its velocity. I am not ready to disagree with Waldemar Lindgren and accept that many commercial placers are substantially enriched by the chemical deposition of gold from solutions; however, I have seen crystalline gold in clayey material quite distant from known sources of primary gold that is dif-

Jan 1, 1992

While coal occurs beneath about 18 percent of Utah, only 4 percent of the state has minable reserves. Utah's coal fields are mostly bituminous. Current coal production in Utah is largely by underground mining, making Utah unique among the coal-producing states. Most coal seams are more than 8 feet thick. Utah's coal resources are about 6.3 billion tons, 1.3 percent of the national reserve. Most of Utah's coal resources are held by the Federal Government and Indian tribes and are mined under lease. The climate of the Utah coal region is characterized by hot, dry summers and cold, relatively moist winters. Normal precipition varies from 6 inches in the lower valleys to more than 40 inches on some high plateaus. The growing season ranges from 5 months in some valleys to less than 3 months in mountainous regions. These extreme climatic conditions make reclamation difficult. Utah gained primacy when its regulatory program was conditionally approved January 21, 1981. Full program approval was obtained March 7, 1983. The Abandoned Mine Land Program was approved June 3,1983. A Federal Lands Cooperative Agreement was signed in March 1987; Utah performs all enforcement activities and some permitting activities on federal lands.

Jan 1, 1992

By J. S. Kirkaldy

A theoretical procedure is demonstrated for calculating two-dimensional binary cellular single-valued interfaces and extended to triple-valued (remelt) shapes. The numerical calculations for the single-valued local equilibrium problem which yield unique shapes as functions of the supersaturation parameter a and the partition coefficient k are reviewed. The cell amplitude L and wavelength A scale identically as the inverse velocity to the 112 power and the aspect ratio r is a constant equal to 312, independently of a and k for a < 0.5.. For 0.5 < a < m, L, A and r decrease asymptotically to zero indicating the finite amplitude nature of the instability at a = 1 and the existence of sub-marginal states which converge to a flat interface at a- m (Glv- m). Scaling comparisons between equilibrium single-valued and triple-valued and deep-rooted non- equilibrium cells are made.

Jan 1, 1992

By K. A. Foo

Minproc Resources Inc. is developing a tailings retreatment project in Bolivia at the Colquiri zinc-tin-silver mine, in the Bolivian Andes. Mining at Colquiri has been continuous since 1940 and COMIBOL, the Bolivian state mining company, has owned and operated the underground mine since 1964. There are 10 million tonnes of tailings at Colquiri containing 0.51% Sn, 4.21% Zn and 50 g/t Ag. Minproc plans to mine and concentrate the tailings at 1.15 million tonnes per year to produce feed for pyrometallurgical upgrading. The tailings are moderately complex, with cassiterite grain size ranging from 200 to 5 pm. The marmatite (ZnFeS) in the tailings is relatively easily recovered, with zinc recovery of 80% to a 40%-45% Zn concentrate. The major problem with the zinc metallurgy is that the marmatite is complexed with iron, which results in iron contents of 14%-17% Fe in concentrate. This makes the product very difficult to sell because of the low Zn:Fe ratio. Most zinc smelters require a Zn:Fe ratio of 6:1 or 7:1, whereas this concentrate has a 3:1 ratio. Concentrate sale terms are therefore unfavorable, and the high cost of transportation from Bolivia to the smelters is an additional burden.

Jan 1, 1992

By J. C. Monette

Stripping of gold and silver from carbon is effected by means of two main processes (AARL and ZADRA ). The main rate-enhancing parameter in the stripping of gold and silver is temperature. A secondary rate-enhancing parameter is ionic strength. (1) Stripping is usually conducted within a solution containing sodium cyanide (0.1 -0.5% ) and caustic ( 1 -3%). The development of a chemistry that increases the rate of gold and silver stripping from carbon in a manner proportional to its concentration is described. Its use in atmospheric and pressure strips is also outlined.

Jan 1, 1992

By Louis W. Cope

Placer material, regardless of the value of gold, tin, titanium, diamonds or other value mineral it contains, remains worthless until the valuable constituent is separated from the bulk of the material. This separation is no mean task when considering that a gold placer containing 0.01 to 0.03 oz/yd3 of gold, which is the range of grade of typical placer deposits; yes, 1:3,000,000! It is a miracle that gold placer mining has ever been profitable. Added to the situation of minute quantities of gold are several other problems, such as the gold often being very finely divided, the association of boulders and clay, and running and/or ground water. As each placer deposit is individual and distinctive, many factors have to be considered in planning the method for gold recovery from the alluvial deposit. Previous chapters have shown that in the exploration and sampling stage, some knowledge of the amount of each size of coarse and fine material which occurs in the deposit as well as the size distribution of the discrete gold particles is determined. Unless informed to the contrary, as a general rule of thumb, plant designers will consider that 40 percent of the material will pass through a 5/8-inch screen or punched plate hole. Also that there may be an occasional nugget and normally considerable amounts of fine gold. The designer must

Jan 1, 1992

By Charles L. Kimbell

In 1988, the aggregate value of total world international export trade in mineral commodities was estimated at nearly $542 billion in current (1988) dollars, which was about 8.6% above the 1987 level, but still 23.7% below the record high set in 1980. Comparable comprehensive data for 1989 were not available in time for inclusion in this chapter, but 1989 returns for developed market economy countries only were 1 1.8% above those for 1988. These countries accounted for about 50% of the total mineral commodity export trade in 1988. It would be unsound to utilize the overall 11.8% growth rate for mineral commodity export trade for these countries to extrapolate the growth in total world mineral commodity trade because these developed market economy countries account for substantially different shares of the five major mineral commodity groups listed in table 2. Specifically, developed market economy countries in 1988 accounted for 56% of world export of ore, concentrate, and scrap, 74.7% of world exports of iron and steel, 71.7% of world exports of nonferrous metals, and 57.8% of all exports of crude nonmetals, but only 26.6% of world exports of mineral fuels. Moreover, even within each of these groups, the actual product mix included in developed market economy country aggregates differ from that in developing market economy country aggregates and in centrally planned economy country aggregates. Nonetheless, an increase of 9% to 12% in the value of world mineral commodity export trade seems indicated by available returns.

Jan 1, 1992

By Pedro D. Lasota

Chile leads the world in copper production with an annual capacity nearing 2 Mt (2.2 million st). Most of the country’s copper production, about 74%, is mined by open-pit mining methods. Open-pit mining also accounts for a major portion of Chile’s production of other commodities, including iron, gold, silver and coal (Table 1). Chile’s mining boom began 10 years ago and is expected to continue through the end of the decade. From 1980 to 1990, copper production in Chile increased 48.7%. During the same period, gold production increased 303%, silver production increased 119% and coal and iron ore production increased 163.7% and 6.6%, respectively (Table 2). It is estimated that copper production will be in the order of 2.3 Mt (2.5 million st) by 1996, when new projects now under construction come onstream. Gold production could reach 35 t (1.1 million oz) and coal production could increase another 1 Mt/a (1.1 million stpy). Open-pit mining has played a significant role in Chile’s minerals production growth. The expected increases in mine operations will come about mainly through new open pits or expansions of existing surface operations (Table 3). However, the number of open-pit copper mines will decrease from 74% to 66% of the total number of Chilean mines. Gold mines will increase from 63% to 69% of the total, while coal mines will go from 41% to 59%. Most all of the present iron ore production is from surface mines and will continue that way.

Jan 1, 1992

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

5.1 INTRODUCTION There are several types of surface ground disturbances, each of which is immediately transmitted to surface structures and causes damage of various forms, depending on the location of the structures in the subsidence basin. Many criteria have also been proposed for defining the potential structural damage. All of these topics will be discussed in this chapter. 5.2 TYPES OF GROUND DAMAGES There are two types of ground damage, continuous and dis¬continuous, that could inflict damages to surface structures. Dis¬continuous ground damage is open fractures of various degrees. Four types of fractures are commonly seen (Brauner, 1973b): 1. Fissures or cracks. Cracks are the most common form of ground damage and range from completely closed to several feet wide. Surface cracks are most prominent when the ratio of mining depth to mining height is smaller than 30 to 50 times mining height. Cracks initiate parallel to, but ahead of the moving long¬wall face at some intervals when the depth-to-mining height ratio is less than 25 to 30. As the face continues to move, they open up and then close gradually, and in most cases eventually close up completely when the face moves farther away. Sometimes when the depth-to-mining height ratio is larger, cracks may initiate be¬hind the face and go through the same cycle. Cracks are also more likely to occur in the hill when the face is moving in the uphill direction. Cracks also occur at or near both sides of the panel edges. Those cracks tend to remain open permanently. When the surface is covered with grass or other vegetation, cracks of less than 1 to 2 in. wide usually do not penetrate it and become invisible on the surface. 2. Steps. A step may occur when the longwall face stops abruptly if the mining depth-to-mining height ratio is less than 20. Steps may also occur along the panel edges. Steps also range from a few inches to a few feet in width and depth. If planes of weakness are oriented favorably, ground will slide along these planes and form steps on the surface. 3. Cave-in pits. These result from local collapse of the ground from the mine level to the surface when the mining depth is less than 150 ft and occur mostly above abandoned mined lands. They may be as large as 40 ft wide and deep. 4. Bumps (compression ridges). Bumps result from ground compression and occur mostly near panel center some time after mining. Bumps of up to 4 ft, but mostly 1 to 2 ft, have been identified. Continuous ground damage refers to the formation of the sub¬sidence basin where continuous nondestructive ground deforma¬tions occur. As mentioned earlier, continuous ground deforma¬tions associated with a subsidence basin include subsidence, slope, curvature, displacement, horizontal strain, twisting, and shearing. 5.3 TYPES OF SURFACE STRUCTURAL DAMAGES Both continuous and discontinuous ground disturbance cause damage to surface structures. A. Structural Damages Due to Discontinuous Ground Disturbance 1. Fissures or cracks. Open cracks can cause dislocation of surface structure if the gaps are sufficiently large so that the struc¬tural elements cannot resist but fail. On the other hand, minor cracks affect only the appearance, and not the structural integrity. 2. Steps. When a surface structure is located on a step, some portions of the structure lose support and become overhung. In the case of a residential house, there will likely be many open frac¬tures in the overhung portions, followed in severe cases by sepa¬ration of the superstructure at the edge of the step. 3. Cave-in pits. If the caved-in pit is larger than the surface structure, the structure will drop into the pit and become unstable. If the caved-in pit is smaller than the surface structure, the struc¬ture may either become overhung or lose support in some portions. In either case, it is unsafe for use. 4. Bumps (compression ridges). Bumps will disrupt roadways or house floor. If located under supporting members of the struc¬tures, it may cause damages. B. Structural Damage Due to Continuous Ground Disturbances 1. Subsidence. Pure subsidence or uniform subsidence over an area does not cause any structural damage. However, if it becomes a topographical low area, it may be flooded with water and make the surface structures unusable. It must be noted that the flat bottom area at the center of the final supercritical subsidence basin does not reach that position suddenly. Rather, as shown in Fig. 3.1, it is subjected to the dynamic surface deformation asso¬ciated with the traveling subsidence basin before it is left behind to be part of the flat-bottom area. Therefore any structure located at the center of the final supercritical subsidence basin must be able to resist the dynamic surface deformation in order not to be dam¬aged. 2. Slope. Ground slope will induce tilting of the structure. Tall structures with small base areas, such as water towers, chimneys, and power transmission towers are most sensitive to ground slope. If the ground slope is such that if after tilting the center of the gravity of the tilted structure falls outside the base area, it will topple, but this seldom occurs. Ground slope will change the designed slope of a buried trans¬portation pipeline, either increasing or decreasing the original slope depending on whether the ground slope coincides with or opposes the original slope. There are maximum allowable final slopes for various types of transporting materials. Ground slope also affects highways and railways. There is a maximum allowable final slope for a railway because tractive effort increases 1/1000 of its weight for every increase of 1/1000 in grade. 3. Curvature. There are positive (convex) and negative (con¬cave) curvatures. When a surface structure is located on a positive curvature, both ends become unsupported, followed by bending upward at the midportion. The top portion is subjected to more severe stretching than the lower one. As a result, vertical cracks with a wider gap at the top occur at the window, door frames, on the walls, and at -the wall joints. V-shaped cracks appear at the

Jan 1, 1992

By L. M. Cenegy

Introduction The formation of scale is common in gold ore processing plants. A working definition of such scale is: "A hard, tightly adhering deposit formed in place by the precipitation of calcium-bearing mineral compounds from water." The most common scale found in gold processing plants is calcium carbonate (CaCO3) although calcium sulfate (CaSO4) is occasionally a problem. The problem of scale in carbon strip circuits Carbon strip circuits present a particularly challenging scale inhibition problem. Many of the factors that tend to promote scaling are present in these systems. For example, carbon strip circuits are run at high temperatures and high pH levels and require long batch cycle times. Tortuous paths are encountered by the strip solution circulating through heat exchangers, pipes and elbows, causing transient pressure drops throughout the system. Severe conditions such as these cause the water to possess a high scaling potential and may lead to the breakdown of some of common types of scale inhibitors. Formation of scale Natural waters contain dissolved minerals and gases that promote scaling. One of the contained gases, carbon dioxide (CO2), is an important factor in scale deposition. Carbon dioxide dissolves in water to yield carbonic acid according to the following reaction: [CO2 + H2O - H2CO3 (carbonic acid)] Carbonic acid rapidly dissociates to yield bicarbonate and carbonate ions depending on the pH of the system: [H2CO3 -s H+ + HCO-3 (pH range 6-10) HCO3 -a H+ + COO (pH range > 9)] In gold cyanidation processes, lime is added to raise the pH of the mill solution to 10 or above to promote cyanidation of the gold and to eliminate the possibility of hydrogen cyanide (HCN) formation. Lime contributes both hydroxyl ions (OH--) and calcium ions (Ca++) to the solution. The normal scale forming reactions in mill water systems were described by Beasley (1973) as: [HCO-3 + OH -s C03 + H2O Ca++ + C03 -a CaCO3] Factor affecting scale deposition According to Linke&apos;s (1958) solubility tables, the solubility of calcium carbonate in carbon-dioxide free water is only 13 mg/dm3 (13 mg/L) at 25° C (77° F). Scale deposition occurs when the concentration of calcium and carbonate ions in the solution exceeds the solubility of calcium carbonate. This occurs, in most cases, when the water has undergone some chemical or physical change. Some typical changes that might occur that lead to scale deposition are discussed below. Temperature An increase in temperature can greatly increase the tendency to form calcium carbonate scale. Studies by Miller (1952) have indicated that calcium carbonate is less soluble at higher temperatures. Hence, high temperatures promote scaling. For this reason, scale is often noticed on heat exchangers, autoclaves and other high temperature surfaces. Pressure A decrease in pressure may lead to an increase in the tendency to form calcium carbonate scale. Fulford&apos;s (1967) work has shown that scale is more soluble at high pressures. Hence, scale is likely to be prevalent in pump suction lines, elbows, baffles and other areas that produce turbulence and subsequent pressure drops. Change in pH Calcium carbonate scale is pH dependent and tends to form more readily at high pH. Any event that causes an increase in pH, such as the introduction of lime or caustic, would tend to initiate scale formation. Since most gold recovery operations are run at a pH above 10, the tendency to form calcium carbonate scale is always great. The use of scale inhibitors to prevent calcium carbonate scale Many products are commercially available to inhibit the formation of calcium carbonate scale. Some of the more effective types include phosphonates, as well as acrylate and maleate-based polymers and copolymers. Many of these products function by means of threshold

Jan 1, 1992

By D. W. Park

Longwall mining is popular in underground coal production in the United States due to higher production rates and safety concerns. Because of the extreme complexity, it is necessary to plan an adequate design to achieve a safe and efficient working place. The proper sizes of yield and abutment pillars and panels can be determined by simulation using numerical modeling techniques. By means of three-dimensional modeling, stresses to be imposed on the pillars, panels, gob, and powered supports can be analyzed. In this study, an initial three-dimensional finite element model was developed and then modified into four different models. Using these models, the numerical outputs of distributed stresses on three different sizes of yield pillars, three different sizes of panels, and two different sizes of abutment pillars were compared and analyzed to determine the most adequate pillar and panel sizes. Progressive failure theory based on the Hoek and Brown failure criterion was used to determine redistribution of stresses in the yielded and failed areas in the longwall mine.

Jan 1, 1992

By Rufus Flinchum

Two of the most critical concerns a blaster faces today are airblast and flyrock. Airblast, sometimes called noise or overpressure, can cause damage to neighboring structures, especially windows. It also is the cause for many vibration complaints. The human sense of hearing is often more acute to identifying source than the sense of touch. When a blast occurs, the airblast is what identifies the event. The vibration that may be felt is then associated with the airblast. Vibrations of greater magnitude, such as passing trucks or construction work on the house, go unnoticed because their sounds are familiar or expected. Flyrock is the number one killer and cause of damage. Elasting laws provide limits for these two concerns. Failure to comply may result in fines, closing of the operation, and even prison. Airblast and flyrock originate from two distinct areas, the open face and the bench surface. Each of these areas is addressed in the detailed proven procedures that follow, and if used by the blaster in conjunction with his own blasting knowledge, a sound blasting plan can be developed to minimize the occurrence of airblast and flyrock.

Jan 1, 1992