Search Documents

By D. S. Barr

The Freeport McMoRan chlorination circuit is comprised of four related processes: ore chlorination, gas scrubbing, chlorine supply and excess hypochlorite removal ("hypo kill"). Each of these processes are described, and related to the pertinent mineralogic components in the carbonaceous ore feed to the plant. The chlorination system in use at Jerritt Canyon to passivate forms of preg-robbing organic carbon has proven to be a cost effective and efficient means to recover gold from low sulfide carbonaceous refractory ores, where gold may not be specifically associated with either the sulfides or the carbon.

Jan 1, 1987

By L. S. Sundae

The Bureau of Mines conducted a series of tests to compare the cutting forces required by radial and point-attack bits when making similar cuts. Three radial and four point-attack bits were tested in two coal mines using the Bureau's in-seam tester to measure coal-cutting forces in situ. Tests were also conducted to investigate the effects of weathering and cleating. The test results show that in each case, at a specific clearance angle, the radial bits required less tangential and much less normal force than the point-attack bits. The resultant of the cutting forces for some types of cut was 50 pct less at mine 1 for radial cuts compared to cuts with the best point-attack bit, and 40 pct less at mine 2. There was some difference between three types of radial bits, but it was not as significant as the difference between each type of point-attack bit. Cutting coal perpendicular to the cleat planes required less cutting and normal force than the same type of cuts parallel to the cleat planes. Test results showed no effect due to weathering on cutting force data. Cutting parallel increased forces only because cuts were made in the rock band.

Jan 1, 1987

By R. M. Yeates

Public concern over possible degradation of groundwater resources has resulted in an array of Federal laws and corresponding state laws to regulate contaminates from solid and hazardous waste. A mine owner must be familiar with environmental regulations which could impact his operation and must know what precautions and corrective actions to take in order to protect his mining operation from potentially expensive remedial actions. The Environmental Protection Agency (EPA), has issued few regulations controlling the management of mining wastes. Federal regulation of mining came primarily under the Surface Mining Control and Reclamation Act (SMCRA) administered by the Office of Surface Mining (OSM). Waste generated from the extraction, benefication and processing of ores and minerals was exempt from regulation under the Resource Conservation and Recovery Act (RCRA), which is EPA's major instrument in controlling surface contaminates. On December 31, 1985, EPA submitted to Congress a report entitled "Wastes from the Extraction and Benefication of Metallic Ores, Phosphate Rock, Asbestos, Overburden from Uranium Mining and Oil Shale", which will be referred to, henceforth, as the Congressional Report. This Congressional Report assessed the possible adverse effects of mine associated wastes. This report is the first step toward developing regulations with which EPA can regulate waste from the extraction, benefication and process of mineral ores.

Jan 1, 1987

By Thomas M. Barczak

This Bureau of Mines report describes research on developing technology to utilize shields as roof load monitors. Three-dimensional equations of static quilibrium are presented for a generic two-legged long-wall shield. The equations are presented in the most general form, assuming a force and moment vector at each reaction by rigid-body analysis of the shield mechanics. The resulting system of equations was found to be indeterminate to a very high degree. A three-dimensional solution to measurement of the resultant reaction on the canopy by the strata activity and shield response required the elimination of several forces or moments that were thought to be nonparticipating or to not significantly affect overall shield mechanics. Required measurements for solution of the equilibrium equations were leg, canopy capsule, and lemniscate link forces. Two-dimensional analysis, which considered forces acting only in the roof-to-floor and face-to-waste plane, was also provided by reduction of the three-dimensional equations~

Jan 1, 1987

By Roger J. Morrell

The Bureau of Mines conducted drag cutting experiments in hard, abrasive rock in an effort to extend the capabilities of an experimental kerf-core mining machine. The basic kerf-core mining machine cannot be used in hard, abrasive rocks because of the high wear experienced by the kerf cutters. These experiments were conducted in an effort to develop a method of preweakening the rock ahead of the kerf cutters in order to reduce the high cutting loads and hence the higher wear rates experienced by the cutters. The two "preweakening" techniques studied were indenting with mechanical wedges and single and double slotting with diamond saws. The best cutter force reduction achieved with mechanical indenting as 70 pct, whereas double slotting achieved force reductions of up to 99 pct. Conceptual designs of preweakening systems that could be retrofitted onto the basic kerfing cutterhead were developed for both the indenting and the slotting techniques. A high-energy impactor with wedge bit was used for the indenting method, and high-pressure water jets were used for the slotting method. A preliminary technical and economic analysis was performed for both of these full-scale systems to illustrate the methodology and to point out the important technical and economic factors that must be considered.

Jan 1, 1987

By P. H. Lu, M. J. DeMarco, J. R. Koehler

Beginning in late 1985 and continuing through 1987, US Bureau of Mines personnel investigated longwall chain pillar and entry design in two and three-entry gateroad systems at a deep underground coal mine in central Utah. To evaluate their respective stability characteristics, four chain pillars and two longwall panels within the two separate entry systems were instrumented with Bureau hydraulic borehole pressure cells to continuously monitor vertical and horizontal pillar and panel stresses through adjacent panel retreat. In addition, supplemental entry closure information was obtained from sites located in the vicinity of the instrumented pillars. The findings presented in this report demonstrate the practicality of evaluating mine pillar stability using in situ methods and support three significant conclusions regarding ground control aspects of the investigated two-entry system: (1) Total areal entry loading was considerably less for the two-entry system, as opposed to the three-entry system, (2) a smaller percentage of opened ground in the two-entry system contributed to a marked reduction in rooffalls, and (3) lower areal loading in the two-entry system suggests improved ground conditions when mining the underlying seam.

Jan 1, 1987

By Berger. P.

The accepted definition of the function of an edge protector fails to specify adequately the several tasks which it must perform to be functionally effective: detailed analysis of these tasks leads to the reasoned conclusion that they cannot satisfactorily be fulfilled by the conventional types of "edge-strips". The true cost of edge protector failure is cumulative: renewal costs are dwarfed by the increased operating expenses and production losses which result from but partial or incipient failure of the edge-strip; yet, the several supposedly improved types, for use with starter-blanks, generally were "built down to a price", prolonging the agony, as it were. Clearly, a fresh appraisal of the problem was overdue, and more especially so with the advent of "permanent" cathodes. As a result, new methods of edge .protection have been developed, including the so-called "EDGEWISE" system in which the present author as patentee *) has a vested interest-which he hereby declares. Due mention is made of recent progress in protecting the edges of aluminium "Jumbo" cathodes in zinc electrowinning operations, although the present Paper is more concerned with edge protection of starter-blanks and permanent cathodes in copper ER/EW processes, where most of the "old" problems now may justifiably be claimed to have been overcome, Mention is also made - albeit at this time necessarily only briefly, and confined to edge protection - of "rigidized" metal blanks and permanent cathodes: a most recent development**) which may prove to represent a "breakthrough": time will tell.

Jan 1, 1987

By R. S. Olsen

Intensely altered rock has had a large effect on slope stability as slopes increase in height at Island Copper mine. Traditionally used, fracture-controlled rock slope stability design techniques have been supplemented with analyses of failure modes which include failure along curved surfaces typical of soil materials. A rock mass rating (Pa) system has been developed that addresses the lower end of rock mass strengths. Rock masses are rated in terms of fabric integrity, alteration, fracturing intensity and gouge strength. Rock mass classes have been defined using statistical frequency distributions of rock mass rating values. Strength values have been assigned to the various classes from shear testing, back analyses of failures and engineering judgment.

Jan 1, 1987

By D. R. Forshey

Although the United States has the world's largest coal reserves, most of those reserves will require underground mining. Unless underground injury and fatality rates are reduced, the number of disabling injuries and accidental deaths will grow as coal production increases. The Bureau's Mining Research Program, designed to reduce the exposure of workers to hazards while improving productivity, is described. Major program thrusts are 1) re- moving the hazards or removing miners from the areas in which hazards exist, 2) developing ways to improve management decisions and mining skills so as to reduce the incidence of situations requiring human involvement in hazardous, emergency, or corrective tasks, and 3) improving, or at least maintaining, productivity so that both the tangible (dollar) and intangible (human) costs are reduced. In these ways, projected demands for coal can be met using resources without an increase in human suffering.

Jan 1, 1987

By J. Allen Hennessy

INTRODUCTION The increasing price of gold and silver over the past 10 years has caused increasing activity in the exploration, evaluation and development of precious metals projects. Many of these deposits are relatively low grade and short lived which makes them economically sensitive to the major project variables such as metal price, capital cost, operating cost and of course, tonnage and grade. These deposits often have a high variability (a coefficient of variation -- o/u -- of 2 to 5) and an intermixing of ore and waste, making ac- curate ore reserve estimation difficult, especially when using traditional estimation techniques. Often, the estimation errors are not the 10-20% that we see in base metal deposits, but the errors in grade and tonnage can be as high as 50%, which can obviously have a very substantial impact on project Recent developments in geostatistics when coupled with a sound geologic under- standing of the deposit can significantly improve reserve estimates of these variable precious metals deposits. Examples will be given of actual deposits where the traditional estimates were significantly different from the mining reality. An attempt will be made to explain the applicable geostatistical tools with a minimum of geostatistical jargon and without complicated formulas. The key to improving the reserve estimates is a clear understanding of the deposit geology and especially the structural controls, the use of local estimation techniques that recognize the intermixing of ore and waste and the effect of selective mining on recoverable reserves, and the use of a global reserve estimation technique to check the results of local estimation. Geologic Controls The vast majority of gold and silver deposits being mined or developed in the western United States would be classified as epithermal deposits. These are formed by hydrothermal fluids (hot water) flowing upward through the rocks and depositing the precious metals as the fluids cool or reach areas of lower pressure or favorable chemical sites. These environments are similar to present day hot springs-type environments with some deposits being clearly associated with surface hot springs such as the Homestake McLaughlin deposit in northern California. These hydrothermal deposits can occur in sedimentary rocks resulting in deposits such as those of the Carlin district or the Jerritt Canyon deposit or the hydrothermal systems can occur in volcanic rocks forming deposits such as Round Mountain, Manhattan or Paradise Peak. The mechanisms of formation were similar in either case with the solution flow controlled by geologic structure and precious metals deposited when the conditions of temperataure, pressure and chemical environment were favorable. The gold and silver hearing solutions travel through permeable faults and fracture systems depositing the metals along these channels. The grades are often highest in the central parts of these conduits (veins) with lower grades in the surrounding rocks. An understanding of the nature, distribution and orientation of these plumbing systems is important to a realistic reserve estimate. The point to be emphasized here is that, good, sound geology in the form of geologic mapping, logging of rotary chip samples and a few carefully logged core holes can signifi- cantly improve an ore reserve estimate.

Jan 1, 1987

By B. Arvidson

Computer-controlled machine sorting may, if properly applied, have a dramatic effect on overall economics of a mine operation. Radiometric and photometric sorters have been used for many years and new developments will be reported, such as a sorter for fine particles and a conductivity/magnetic sorter. Application examples with emphasis on precious metals will be given. Economics for some of the projects will be reviewed and discussed. Sorting underground is shown to be particularly attractive, but machine sorting would be profitable in most cases based on savings in transportation and milling/beneficiation costs only.

Jan 1, 1987

Provide an inexpensive, simple means of supporting highly yielding ground In underground mines. Approach The Bureau of Mines developed a high capacity support post made from standard steel pipe which, when using a 60-inch post configuration, has a 45-ton capacity and a yield length of 24 inches. How It Works The post mechanism is a three-piece unit consisting of a top and bottom leg (made from standard steel pipe) and a separate foot bracket. During installation in the mine, the bottom leg is placed on a relatively flat surface on the mine floor and the top leg is placed over it until its flared end contacts an expansion ring attached to the bottom leg. As the roof and floor converge, the flared end of the top leg is forced into the expansion ring, causing the walls of the top leg to be deformed radially and along the axis. The mechanism will yield until the unit bottoms out after about 24 inches of yield.

Jan 1, 1987

By D. Farnell

Large semi-autogenous (SAG) or autogenous grinding mills have become the work-horse of the modern high volume concentrator. They typify the economy of scale - fewer, larger machines doing more work, more economically. With fewer machines, equipment reliability becomes of paramount importance. Realizing this, companies installing new or modernizing existing facilities have placed extraordinary emphasis on purchasing a reliable mill. This, in turn, has had a significant impact on mill design. Kennecott And Codelco - Two Different Approaches Last year, two of the world's largest copper producers, Codelco and Kennecott, undertook the modernization of their main grinding facilities at Chuquicamata and the Utah Copper Division (UCD) respectively. Both selected semi-autogenous milling and both, recognized the importance of the reliability of the primary mills. Each, however, decided on a different approach to optimizing reliability. Codelco placed the emphasis on technical innovation in design and opted for a gearless driven mill. Kennecott chose the more conservative approach of active participation and exceptional quality assurance in mill design and manufacture.

Jan 1, 1987

By E. R. Cole

One objective of Bureau of Mines recycling research is to devise technology that enables recovery of metals and minerals from wastes. From October 1982 through September 1985, researchers at the Bureau and at the University of Missouri Rolla (contract H0222002) investigated the use of nonferrous flue dust with varying Zn contents (11 to 66 pct) as a source of Zn for electrogalvanizing steel wire. The waste dusts used were from a secondary Cu smelter, a brass smelter, a Pb smelter, and a water treatment plant. The dusts were leached in H2S04, and the leach solutions were treated to make electrolyte for electrogalvanizing steel wire using soluble Zn anodes. Cyclic voltammetry was used in an inno-vative method to evaluate the quality of the electrolytes used for elec-rogalvanizing. After electrogalvanizing, the wire was drawn on a labo-ratory draw bench to simulate industrial practice. Corrosion resistance was measured by a number of electrochemical techniques and by the stan-dard ASTM salt-spray tests. After successful bench-scale tests, the process was demonstrated in an industrial pilot plant. Results indicate that nonferrous flue dusts can be used as a source of Zn for electro-galvanizing if certain impurities are either partially or completely removed from the starting electrolyte.

Jan 1, 1987

By R. England

"This paper describes the objectives and design parameters for the operation of a computerized In-The-Hole (I. T.H.) Drill. The principal objective is to add computer control to an Inco 00-60 I. T.H. (CMS-CD-90) drill in order to drill holes with greater accuracy. The computer provides control of the angle of the hole by maintaining the orientation of the drill head, and optimizes the straightness of the hole by maintaining a constant force on the drill bit.The second objective is to provide the greatest degree of operational automation, so the objective outlined above can be accomplished with a minimum of operator intervention.In order to provide full operational automation it was necessary to also provide the capability for the computer to add and remove drill rods. To accomplish this, a rod-handling mechanism consisting of a rod storage rack and rod manipulator arms was used.IntroductionMining machinery that lacks automatic control has been found to show a high degree of variation in work output and performance quality when operated by different personnel. Differences in operator attitude, judgment, and skill are reflected directly by production statistics. The addition of automated control has the potential for considerable improvement in machine life and performance. Even with a more acceptable mine environment and much safer conditions than ever before, situations still exist where it is preferable to remove personnel for reasons of safety as well as productivity. Typical advantages of such situations are automated skip loading and hoisting, and the use of remote control load-haul-dump units exposed to open stopes.Other cases arise where heavy work is required under conditions where lighting is poor, floors are slippery, noise levels are high and dust and oil mist exist in the atmosphere. I.T.H. drilling is carried out under such conditions and is one operation where automation can easily be justified."

Jan 1, 1987

By A. M. Krzanowski, T. S. Golosinski

"This paper presents results of a study undertaken to determinethe feasibility of mining plains overburdens with bucket wheel excavators. Based on extensive geotechnical testing of overburdens under study, the relations between material geotechnical properties and its cuttability were defined. The properties with the highest correlations to the cuttability werethen used to develop the material diggability classification. This classification may be used for identification of overburdens and coals mineable by bucket wheel excavators.IntroductionLow cost of mining and high productivity can be achieved when mining unconsolidated soils and soft rocks with bucket wheel excavators. As a result this mining equipment will likely be introduced into plains coal mines. At present there are plans to use a bucketwheel excavator (BWE) in at least one mine by the end of this decade. Unfortunately, the performance of a BWE deteriorates rapidly with the increasing strength of mined material. To avoid costly misapplication, material diggability must be defined in advance of an application (i.e. the force required at the cutting edges of BWE buckets must be quantified). Correct definition of material diggability permits reliable selection of a BWE, or may indicate unsuitability of this equipment for a particular application.The reported studyu i was undertaken to investigate the diggability of typical prairie overburdens and thus provide a guidance for likely future applications of bucketwheel equipment. Investigations concentrated on the parts of overburden most likely to create problems for a BWE mining. These are defined in Table 1. At present, thin layers of the two investigated materials (samples K and L) are mined by a BWE in an oil sand mine, after being loosened by blasting."

Jan 1, 1987

By Joyce Lappin-Randolph

In 1977, Vertical Crater Retreat (VCR) Mining was developed at the Homestake Mine and by 1983 had become a fully integrated mining method contributing 60% to total underground production. VCR has proven successful for continuous ore blocks exceeding 55,100 tons (50,000 st) with dips greater than 60" and provides a productivity average of 39 tons (35 st) per man shift (tpms) which is 92% greater than Open Cut-and-Fill. Discontinuous ore bodies, small pods, or flat structures not amenable to bulk systems are mined with Mechanized Cut-and-Fill (MCF) and have been able to achieve a 32 tpms (29 st) average productivity. Small, low grade, remnant ore bodies were not economically viable with large scale bulk techniques and couldn't support the development required for a MCF system. As a result, Homestake began researching modified bulk mining methods to increase production rates and maintain safety, while lowering costs. A modified version of VCR with significantly diminished development was prototyped in an effort to reduce initial capital investment and expedite the production phase. This modified method is called Small Block Vertical Crater Retreat (S. B. VCR). Geology The Homestake Gold Mine is located in the northern Black Hills of South Dakota at Lead. Having been active since 1876, it now extends from the surface to the 2,440 m (8000 ft) level underground.

Jan 1, 1987

By R. Jin

The hydrophobicity of six coals ranked from lignite to anthracite is studied through contact-angle measurements, bubble attachment-time measurements, FTIR spectroscopy, and Hallimond-tube flotation. The preliminary study shows that the hydrophobicity of coals can be told by the bubble attachment times of coals (a kinetic criterion) or by the contact angles (an - equilibrium criterion). A general agreement between flotation response of coals and measured bubble attachment times or contact angles is observed in the present study. However, the study also shows that the hydrophobicity of coals can be predicted by FTIR spectroscopy work with proper manipulation of the spectra. Both hydroxyl and carboxyl groups in the coals are proven by FTIR work to be responsible for the change of coal hydrophobicity. A new criterion for the hydrophilicity index of coals from FTIR spectra is introduced through the study.

Jan 1, 1987

By Robert A. Jankowski, Charles A. Babbitt, Natesa I. Jayaraman

The U. S. Bureau of Mines, through a contract research program with Foster-Miller, Inc., has identified guidelines for the selection of the most effective water spray system and water flow rates for use on continuous mining machines. Specifically, these parameters were modified to obtain maximum dust control with regard to quartz dust exposure and more stringent respirable dust standards due to quartz. A novel water spray system, consisting of flat fan spray nozzles, mounted across the top of the mining machine, along with high flow, flat fan and higher pressure hollow cone nozzles mounted under the boom has been identified and tested. The anti-rollback/underboom spray system minimizes dust rollback while increasing dust knockdown by its unique positioning of spray manifolds and orientation of spray nozzles. Respirable dust suppression characteristics of the system acted in three ways: - by wetting the surface of the broken coal material to prevent dust from becoming airborne; - by controlling the airflow pattern at and near the face to minimize dust rollback to the operator Is control location; and - by dust knockdown, i.e., airborne capture, or scrubbing of airborne dust from the air. During underground trials, the anti-rollback/ underboom spray system reduced dust levels at the operator's position and in the immediate return by 55 and 15 pct, respectively, when compared to a conventional spray system. Quartz dust levels at the operator '8 position were essentially eliminated, while quartz dust levels in the immediate return were reduced by 57 pct. Applying the concepts of this technique throughout the mining industry should reduce the health hazard associated with excessive exposure to respirable quartz dust, as well as allow coal mine operators to comply with the associated, more stringent, respirable dust standards.

Jan 1, 1987

By D. R. Dance

The Resonant, or as it has more commonly come to be known the 'Sonic' Pile Driver, dates back to the early 1960's, when prototypes were produced by Charlie Guild, of Providence, Rhode Island, and A1 Bodine of Los Angeles, California, these were later to be developed into the unit known as the BRD 1000. Based on this initial work, the Shell Oil Companies of Sonico and The Resonant Pile Corporation, produced and operated 30 of these BRD 1000 machines, which were used throughout the U.S.A. and Canada on a wide range of foundation projects. Subsequent to this, Raymond International and G K N, of England, operated units on programs; the G K N units being of slightly modified configuration. In 1973 Hawker Siddeley Canada Ltd., acquired the license for the Pile Driver and related systems with the intent of promoting the use of the machines to install support pilings on the Alyaska Pipeline Project, but this did not materialize due to problems with the oscillator. After radical redesign and field testing of the oscillator system the unit was employed on a number of test projects principally in Northern Canada and Alaska.

Jan 1, 1987