Search Documents

By J. E. Lonergan

The in-pit placement of crushing and conveying equipment results in a flattening of the pit slope of a multiple-bench open pit mine. To maximize the economic benefit of lower haulage costs associated with in-pit conveying, one must minimize the cost of the flatter slope which is expressed in terms of additional stripping or tied up ore. A computer program that compares the tonnage aspects of various conveyor layouts will be discussed.

Jan 1, 1985

By C. F. Winquist

The Bureau of Mines is engaged in research to evaluate the effects of cutter bit wear at coal mine faces. This paper addresses one element of conical bit wear, bit rotation. A discussion on mounting configura-tion and bit forces and their effects on rotation is presented. The effects on rotation and bit forces of bit attack angle, cutting depth, and skew are determined for two types of conical bits during linear cutting of sandstone-inclusive rock. The results indicate that a 10° negative skew angle and 35° attack angle produce the maximum rotation of 17.5° for each foot of cutting. Data on bit rotation and bit forces are presented in an appendix.

Jan 1, 1985

By D. Malhotra

Climax byproduct-plant tailing assayed 0.019 percent WO3. Pilot-plant and laboratory tests were performed to investigate the possibility of recovering additional tungsten values from the byproduct-plant tailing. The paper discusses the methodology used in the study and the results of this investigation.

Jan 1, 1985

By J. A. Meech

An analysis of screen design options on the operating efficiency of secondary crushing plants has been conducted using a dynamic computer model. The model allows for the simulation of a wide variety of crushing circuits and can be run on either a microcomputer (IBM PC/XT) or a large time-sharing mainframe computer. Size reduction and separation characteristics of crushers and screens are based on standard manufacturer design and performance data. Input/output routines are available in tabular, alarm or strip chart recorder modes to facilitate operation of the program. A number of alternate circuit designs are compared to show the influence of surge capacity, screen size and area, screen deck location, and closed side crusher settings on the operation of a 10,000 ton per day plant. The program is currently in use at Queen's University to teach plant operations and control. It has potential to be a valuable tool for operator training.

Jan 1, 1985

By Pamela J. Watson

This report presents a Bureau of Mines literature survey that provides a data base useful for current and future studies in the area of chemically enhanced drilling and cutting. Publications describing laboratory testing and field studies of drilling and cutting with chemical additives are reviewed. Significant results are summarized and tabulated by rock or material type and also by chemical additive, with extensive references. Selected studies related to fluid-enhanced processing or material testing are summarized in the appendixes.

Jan 1, 1985

By W. S. Cavender

The Round Mountain mining district, Nye County, Ne- vada, was discovered in 1906 on claims owned by Lewis D. Gordon. Initial mining operations uncovered gold veins of spectacular richness, and within a few days of discovery, Gordon sold his controlling interest for some $87,000. From this sale emerged the Round Mountain Mining Co., predecessor of Nevada Porphyry Gold Mines, Inc., the latter destined to become the major property owner in the area. Vein mining in the district continued sporadically into the early 1930s, yielding 9.3 Mg (330,000 oz) of gold plus substantial silver credits from approximately 626 kt (690,000 st) of ore. In addition to the lode deposits, the early miners recognized the placer potential in the alluvial fan material accumulated around the west and north sides of Round Mountain itself. Intermittent placer operations were carried out for a number of years, and in the 1940s and 1950s, Round Mountain Gold Dredging Co. worked the placers under a lease from Nevada Porphyry Gold Mines. The last placer operation terminated in 1959 when it, like some of its predecessors, proved uneconomic. Total placer production for the district is estimated at 3657 km (4 million yd) of gravel containing 59 Mg (210,000 oz) of gold and possibly 2.0 to 2.3 Mg (70,000 to 80,000 oz) of silver. Round Mountain is a small hill situated on the east flank of the Toquima Range in central Nevada. The hill is com- posed of relatively flat-lying Tertiary rhyolitic ash flow tuffs, which overlie Paleozoic metasediments and Cretaceous granites. Throughout the surrounding Round Mountain mining district, most of the known gold ores occur in the tuffs, although the metasediments and granites are also mineralized. Mineralization is structurally controlled, principally by a series of northwest-trending shears and shattered zones. Vein, stockwork, and disseminated ores occur, usually containing simple quartz-pyrite-gold mineral assemblages. The gold itself is electrum, having a silver content of 30% to 40%. In September, 1967, Elwood Dietrich, a prospector and mine promoter, obtained a purchase option on the 4452 ha (1 1,000 acres) of mineral rights held at Round Mountain by Nevada Porphyry Gold Mines. The original option had a buy-out price of $1 million and was established through Dietrich's friendship with officers of Nevada Porphyry. In April, 1968, Dietrich conveyed his option to Ordrich Gold Reserves Co., a partnership created by a group of west coast investors, mostly employees of the airline industry. There- after, Ordrich invested considerable funds in trying to test and develop the property, but soon recognized the need to seek financial and technical support from the mining industry. In December, 1968, Dietrich contacted Wayne Cavender, then Regional Geologist, Southwest, for Copper Range Exploration Company (CRX) in Tucson, Arizona, and made a data presentation. Shortly thereafter, Cavender was appointed Manager of Exploration and Chief Geologist for Copper Range Co. (parent company of CRX), New York City, and he asked C. Phillips Purdy, CRX Regional Geologist, Northwest, to make an initial property examination. Purdy's one-week field study took place in March, 1969, and resulted in a recommendation that CRX pursue its investigation of the property. The presence of low-grade gold mineralization in both the alluvial gravels and in the bedrock was verifiable, but the placer was deemed to have the greater immediate economic mining potential. At that time, gold was in the $1.41/g ($40 per oz) price range. Working from Purdy's information, Cavender decided to attempt acquisition of the property, and the first in a long series of negotiations was initiated with Ordrich. Basically, CRX felt that the placer had a promising potential for several reasons, including (I) past operators had recovered free gold but not the gold contained in the pebble fraction of the gravels; (2) past operations appeared to have been ineffectively designed or managed and not costefficient; and (3) the price of gold appeared to be poised for an upward move. Negotiations with Ordrich were prolonged and difficult, with CRX competing against several ma* mining companies, but finally an agreement was reached, effective June I, 1970. Gold was then back to $35. It is believed that, in

Jan 1, 1985

By Cal D. Iles

Decreasing ore grades and increasing labor and material costs have seriously eroded the economic vitality of many mining operations. Coupled with global economic stagnation and recession in the early 1980's, these conditions have forced reevaluation of operating strategies and methodologies with the objective of remaining competitive in a world marketplace. A concept offering large potential benefits is hardrock portable crushing and conveying. Implementation of this system at Duval Corporation's Sierrita open pit copper-molybdenum mine (Figure 1) has significantly reduced mining costs, becoming a major part of Sierrita's cost reduction strategy. Located 48 km south of Tucson, Arizona, the 209 000 t/d property has one portable 60x89 gyratory ore-crusher in operation with tentative plans for two additional units.

Jan 1, 1985

By R. G. Lundquist

The idea that fragmentation for mineral processing results from some tradeoff between increased drilling and blasting and increased load on the primary crusher is well known. In a previous paper (Lundquist and Konya, 1963) the authors reported on the results of a laboratory scale study which attempted to quantify this tradeoff in energy terms. If we look only at the production of new surface area, blasting is 1700 times as energy efficient as crushing. On an energy cost basis, crushing is 57 times as expensive per unit surface produced as blasting with dynamite and more than 700 times as expensive as blasting with ANFO. The comminution process at an open pit operation starts with the drilling of blast holes and ends after the material has gone through the fine grind circuit. Operators usually break the process into several separate operations and do their cost analysis based on this approach. Often drilling and blasting is considered as one system and crushing and grinding are considered as one or two separate and independent systems. Operators will independently optimize each system. The cost for the drilling and blasting system is obvious in operations which use contract drillers to do the drilling and either contract the blasting to a distributor or do the blasting themselves. The cost of rock breaking in this manner is readily available since the contract driller will supply a monthly drilling cost to the operation and either the distributor who is contracting the blasting or the distributor who is supplying the powder to the blasting operation will also supply a monthly billing. In either case, the costs can easily be seen on a monthly or per ton basis. They are not difficult to compute even when drilling and blasting are done entirely in-house.

Jan 1, 1985

By R. P. Vinson

The Bureau of Mines conducted a series of tests to determine how well the Bendix BDX 60, the Gilian HFS 113U, the MSA Fixt-Flo, and the Spectrex PAS-3000 dust sampling pumps control the flow rate at 2 L/min. These tests were performed because users need to know the performance characteristics of sampling pumps to select the pump that best satisfies their sampling requirements. Long-term (6- to 8-h) flow stability at various backpressures was examined in relation to the flow control tolerance of ±5% of the flow, the level imposed by Federal regulations; four of the five Bendix pumps did not meet the criterion for this test, which was passed by all other pumps tested. Flow control recovery times were measured at transient backpressures; all pumps evaluated met the criterion for this test. The low-flow indicators of the sampling pumps were tested; only two Bendix pumps and one Gilian pump met the criterion of indicating a flow change greater than ±5%. In the pulsation flow measurement test all of the pumps passed, with pulsating flows greater than 20 Hz. The Bureau also evaluated the manuals accompanying the sampling pumps. All were judged adequate except the Spectrex manual, which was judged poor.

Jan 1, 1985

By M. Hayashi

The Bureau of Mines conducted laboratory studies on low-grade vanadiferous silicates from the Pumpkin Buttes and Nine Mile Lake deposits of Wyoming to examine techniques for extracting vanadium and uranium. Recovery from low-grade sources such as these could contribute to future vanadium production and reduce reliance on vanadium imports. The Pumpkin Buttes samples contained 0.03 to 0.04 pct V205 and 0.06 to 0.12 pct U308; the Nine Mile Lake samples contained 0.02 to 1.0 pct V205 and 0.06 to 0.19 pct U308" Leaching the Pumpkin Buttes samples for 18 h at 800 C with addition of 200 lb/ton H2S04 resulted in recoverey of 80 pct of the vanadium contained in the samples. The Nine Mile Lake samples were readily leached, yielding 78 to 94 pct of the vanadium after 3 h at 800 C with addition of 100 lb/ton H2S04, A solvent extraction procedure was used to selectively recover urani-um from Pumpkin Buttes and Nine Mile Lake leach solutions and to recover vanadium from the raffinates. In batch shakeout tests, Alamine 336 recovered over 95 pct of the uranium from leach solution adjusted to pH 1. Di-2-ethylhexyl phosphoric acid and Cyanex 272 recovered vanadium from the uranium raffinate after reduction and adjustment to pH 2; vanadium extractions of up to 96 pet and 92 pct, respectively, were achieved.

Jan 1, 1985

By G. A. Smyres

The Bureau of Mines investigated a HCI-02 leaching procedure to recover Cu, Ni, and Co from a low-grade bulk sulfide flotation concentrate prepared from the Duluth gabbro complex. Since the Duluth gabbro complex is the largest known and unexploited Ni resource in the United States, the development of options for extracting the metal values from the flotation concentrate of this domestic resource is necessary. Conditions were determined for producing a pregnant solution low in Fe to facilitate recovery of the metal values. Leaching experiments were conducted at 15 pct solids, 1000 to 1200 C, 0.2 to 0.3 g HCI per gram concentrate in a 50-gal reactor pressurized to 50 pSig with 02. Base metal extractions from the concentrate were, in percent, 90 to 92 Cu, 99 Ni, 97 to 99 Co, and 0.1 .Fe. Precious metals extractions were erratic and unpredictable; at best their extractions were, in percent, 55 Au, 90 Ag, 40 Pt, and 45 Pd. The reaction time at 1200 C was 0.5 h. The use of compressed air instead of 02 as the oxidant was also investigated. Solvent extraction using LIX 622 was used to remove Cu from the pregnant solution. Cementation on Cu was tested for precious metals recovery, while sulfide precipitation was used to produce a Ni-Co product. A conceptual flowsheet for treating the Duluth gabbro concentrate is proposed.

Jan 1, 1985

By M. G. Hester

The ore reserve modeling of stratiform uranium deposits to be mined by selective underground mining methods must be done with consideration of the erratic nature of the ore forming processes that produced the mineralization. Estimation methods that model the uranium grade as a smooth transition between high grade and low grade drillhole intercepts tend to greatly overestimate the ore tonnage. Care must be taken to first establish realistic ore pod geometries and then estimate the grade of the reserve units within the pods.

Jan 1, 1985

By Cesar A. Busnardo

The carbonatite orebody in Jacupiranga is situated some 230km (140-mi) southwest of Sao Paulo and is mined by Serrana S/A de Mineragao, producing an apatite concentrate for fertilizer production and a calcite tailing for cement manufacture (see Figure 1). The orebody (Table 1) is mined by open pit and the total production is 4.5 million mt/year of carbonatite ore with a further 2.2 million mt/year of overburden. The carbonatite low-grade ore (Table 2) is fed to the concentration plant at 460 mt/h , comprising of four parallel lines of grinding, by rod mills 2.7m x 4.5m (9 x 15-ft), operating in closed circuit with hydrocyclones. The grinding circuit product is deslimed in four stages using hydrocyclones and the deslimed product is conditioned with corn starch and subsequently floated, using fatty acids as collector to, recover the apatite.

Jan 1, 1985

By John Lovering

The Afton property is located 180 air miles East-Northeast of Vancouver and nine miles West of Kamloops, a city of 60,000 people, in South Central British Columbia, Canada. The mine is adjacent to the Trans-Canada Highway at an elevation of 2,200 feet above sea level. The orebody is a porphyry, copper deposit that has undergone supergene alteration. The-major economic minerals in the supergene zone are native copper and chalcocite with chalcopyrite and bornite in the hypergene areas. The grade is one percent with an overall copper distribution: 70% native, 25% chalcocite and 5% chalcopyrite with bornite and covellite. The ore also contains important, but variable amounts of gold and silver.

Jan 1, 1985

By K. K. Feng

"Spontaneous combustion has always been a problem in coal mines and is identified mainly with the mining of low-rank coals. The liability of coals to spontaneous heating is only one of the factors in determining whether spontaneous combustion will occur. However, knowledge of the relative oxidizability of the coal is a useful factor to take into consideration when selecting new coal seams and mining methods for future mine development.Four methods (static isothermal, ignitability, adiabatic and dynamic) have been used to compare the relative liability of Canadian coal to spontaneous combustion and to investigate the mechanism of spontaneous combustion of these coals. Among these f our methods, the static isothermal method is considered to be the best indicator of the susceptibility of various coals to spontaneous combustion. Western mountain coal adsorbs more oxygen and has a higher tendency to undergo spontaneous combustion than the Harbour seam coal of Nova Scotia. It has also been observed that a higher methane content in coal will indicate a lower liability to spontaneous heating."

Jan 1, 1985

By Dennis Arthur Fenton

The hydrodynamic bearing was first described by, Reynolds in 1886, and has since been widely applied in motors, engines, compressors, hydroelectric turbines, and other machinery. For various reasons, the hydrostatic bearing currently predominates in the large, horizontal rotating machinery field (e.g. grinding mills). However, the current industry trend towards increasing size and energy efficiency has resulted in renewed interest in the advantages of hydrodynamic bearings. These advantages include structural improvements, reduced bearing friction, improved bearing life, improved transient characteristics, and reduced lubricant pump size and power requirements. In particular, the higher energy efficiency results in substantial savings on large machines. This paper describes some aspects of the design of large hydrodynamic bearings based on thirty years, of experience in the design of such bearings on grinding mills ranging in journal size from 2.1 m to 6.4 m, see Table 1.

Jan 1, 1985

This treatise presents the application of the vertical furnace in a carbon regeneration system. Comparison is made to a rotary kiln. The construction, operation and control of the vertical furnace and system components are discussed. Advantages include high efficiency, fuel economy, minimal mechanical apparatus and maintenance, atmospheric and temperature control, ease of operation and reliability.

Jan 1, 1985

By C. P. Mishra

The Bureau of Mines investigated the availability of mercury from 22 deposits in market economy countries. The 15 significant deposits evaluated have demonstrated resources of approximately 25 million metric tons of ore containing 5.3 million flasks of mercury and account for more than 85 pct of the demonstrated resources for market economy countries. Using data gathered as part of its Minerals Availability Program, the Bureau determined the mercury production potential of each deposit. At a January 1984 mercury market price of $300 per flask, the deposits evaluated could economically produce an estimated 2.5 million flasks of mercury from six mines operating at the time of this study; no mercury is available at this price from nonproducing operations. At $600 per flask, approximately 4.5 million flasks of mercury are available. For production costs up to $300 per flask, operating mines could supply mercury at the current production rate of 114,000 flasks per year until 1988, when the amount of mercury available from these deposits would decrease. This decline could be offset by the development of resources currently reported at the identified level (17 million flasks) at much higher production costs.

Jan 1, 1985

By William F. Stowasser

The United States has traditionally been the world's largest producer and net exporter of phosphate rock and related fertilizer products with the exception of rock exports from Morocco. In recent years, however, U.S. producers have faced increasing competition from operations in foreign countries, leaving the future position of the U.S. phosphate .industry as a leader in the world markets somewhat less certain. This paper will review the U.S. phosphate rock industry in relation to its known demonstrated reserves, its historical and present production and export levels, and its future mining potential. The paper will include an analysis of the availability of phosphate rock in the United States represented by cost-tonnage relationships. The U.S. phosphate rock industry has for decades provided raw materials at reasonable costs to the phosphate fertilizer industry, and the fertilizer products have been made available to both domestic and international markets. Natural soils normally contain low quantities of phosphorus, and cultivation exhausts the available phosphorus through the removal of harvested products. Yields diminish, and it becomes necessary to apply phosphorus to the soil in an amount at least sufficient to compensate for removal. Raising the level of phosphorus also permits nitrogen and potash fertilizer nutrients to be effective and sustain the high crop yields necessary to support increasing food demands. In only a few areas of the world are soils, climate, rainfall, and low-cost phosphate fertilizer available to assure high agricultural yields in successive years. One of these areas is the central United States and south central Canada. By contrast, in the Soviet Union, the weather conditions in farming areas frequently cause crops to either bake or drown in the field. To attempt to counter the effect of weather on production, the U.S.S.R. has increased use of fertilizer and equipment in recent years. The effect of fertilizer on various crops has been documented, and in all cases, improvements in yield and plant development were noted, as was the ability of fertilizer to mitigate the effects of unfavorable climatic conditions. Phosphate resources can be classified as either identified or undiscovered. In the identified classification, we are principally concerned with demonstrated phosphate resources, or those that have been measured or indicated. In the southeastern United States, the phosphate mining areas of Florida and the Carolinas have been explored and drilled extensively in attempts to locate new deposits. The exploration programs indicate that another Florida Bone Valley Formation or North Carolina Pamlico River Deposit is unlikely to be discovered in the southeastern U.S. coastal plain. Phosphate rock deposits of commercial interest in the western United States are located in Montana, western Wyoming, northern Utah, and southeastern Idaho. The deposits are in the Permian Phosphoria Formation with most of the mining activity occurring in Idaho. Although substantial demonstrated resources have been identified, recovery costs and the field's isolation from markets have restricted growth of the industry in the west. The phosphate rock deposits in Tennessee are well known, and it is estimated that about 29 million metric tons1 are potentially recoverable. Undiscovered deposits of brown rock in Tennessee would likely be quite small.

Jan 1, 1985

By R. L. Atwood

This paper discusses the metallurgical and Manufacturing input to Merrill-Crowe plants. Topics treated are pregnant solution chemistry, clarification, degassing, zinc addition, product filtration, accounting, and costs.

Jan 1, 1985