Search Documents

By Robert J. Timko

Because of leakage through and around permanent stoppings in underground mines, more air must be forced into a mine than would otherwise be required for ventilation. As power costs increase, costs resulting from air leakage add increasingly to the operating costs of mining. The Bureau of Mines evaluated four different stopping construction techniques based on the ideas that (1) airtightness could be enhanced by brushing rather than troweling on mortar sealant and that (2) modified mortars (mortars containing glass fibers and other additives for increased strength and adhesion) would improve sealing performance. Air leakage tests comparing conventional to modified stoppings were done when the stoppings were built, after 6 months, after 1 yr, and following simple maintenance. It was found that stoppings can be built and maintained better if-- The area where a stopping is to be built is properly prepared. Stoppings are constructed using the techniques devised by the Bureau. Stoppings are periodically examined for leaks. Stoppings found to be leaking, especially at the perimeters, are resealed.

Jan 1, 1983

By W. R. Byrnes

This project was initiated on October 1, 1980 and will be completed on December 31, 1983. The project was Initially approved and funded by the Office of Surface Mining and subsequently was moved to the jurisdiction of the Bureau of Mines. It was administered through the Indiana Mining and Mineral Resources Research Institute. The research was done to assess reforestation success and ultimate productivity for areas reclaimed under the Surface Mining Control and Reclamation Act of 1977 (P.L. 95-87). The Permanent Regulatory Program for implementation of P.L. 95-87 Includes provisions for revegetation that require seeding of ground cover plants to control erosion until permanent vegetation such as tree species Is established, and restoration of mined land to its original or better productivity. Much of the land to be surface-mined presently supports forest cover and it is anticipated that reconstructed minesoils will exhibit high productive potential for hardwood tree species. Hence, information was needed on compatibility of ground cover and tree seedlings when established concurrently as well as on revegetation success under postmining versus premining conditions.

Jan 1, 1983

By Michael D. Loy

While the coal industry in general has been slow in accepting automation, the last few years have seen a myriad of products developed by the private sector. These packages run the full gamut from sophisticated geological information systems to line entry discounted cash flow analyses. This paper is an attempt to unravel the confusion that may exist about mining software. Discussions will highlight major differences between software products (such as block vs. grid models, prefeasibility programs vs. Monte Carlo analyses), briefly discuss known vendors, list known package features and touch on hardware requirements. The paper also focuses on the costs of automation (both software and hardware), possible trade-offs, advantages to in-house systems (vs. timesharing), a recommended review/selection process (including suggested RFP format), a test case procedure, when to bring in a consultant, and staffing considerations.

Jan 1, 1983

By Jerry Tien

Mine regulators are normally used for proper air distribution in underground mines. They are deliberately introduced resistance in the regulated airway, and by altering sizes, they can distribute specific air quantities to regulated splits and free splits (4, 5). The enactment of the Federal Coal Mine Health and Safety Act of 1969, the Federal Mine Safety and Health Amendments Act of 1977, and the regulations adopted by the Mining Enforcement and Safety Administration (now called the Mining Safety and Health ministration) prompted greater discussions of optimal mine regulator locations because of the Act's stringent ventilation requirements (2, 3). For example, by requiring the separation of the air used in the belt haulage entries from the intake and return airways, the regulations required the creation of a third type of airway---the neutral airway, as opposed to the intake and return airways, adding to the complexity of a mine's ventilation network. It is the intent of this report to show that panel regulators should be located in intake airways at the neck of a panel for a blowing fan system and in return airways at the neck of a panel for an exhausting fan system in order to achieve optimal air control. A computer simulation model is used to determine optimal mine regulator location.

Jan 1, 1983

By Richard W. Patton

With the advent of the Clean Air Act and the installation of flue gas desulfurization (FGD) equipment (scrubbers) on coal fired power plants, the management of solid wastes has taken on added importance. Aside from the large amounts of fly ash and bottom ash usually generated, large quantities of liquids in the form of scrubber sludge are also produced. These wastes must be disposed of within the constraints of land and water quality regulations. This paper describes the practices adopted by the electric utility industry in denting with this problem, including methods of generation and treatment, quantities and characteristics of the materials, and transportation and disposal practices. The paper also briefly describes final product characteristics and several applications for commercial utilization and land reclamation.

Jan 1, 1983

By N. Lecuyer

"During early 1980, pre-production work commenced at the ""Les Mines Gallen"" project, north of Noranda, Quebec. As a result of the acid mine water associated with this property, a major pre-production phase included the installation of a water treatment plant to render the water environmentally suitable.This paper emphasizes the planning, installation and operational factors of the treatment plant necessary to the success of the mining operations and the maintaining of a clean environment.Introduction,T he Gallen Project is a zinc, gold and silver open-pit mining operation approximately 10 kilometres north of Noranda, Quebec. This property has a long history, with initial diamond drilling done in the early 1930s and underground mining taking place between 1953 and 1962. This property was reactivated in 1980, with production scheduled a t a rate of 45,000 ton s per month.Included in the reactivation plans for the property was the installation of a water treatment plant to treat the acidic mine water.Plant DesignThe requirements for the Gallen water treatment plant were two-fold. Firstly, it was necessary to neutralize the acid water and secondly to produce a sludge containing metal hydroxides and sulphates which would be stable when stored, and a clarified overflow meeting governmental regulations to be discharged to the environment.The flow sheet (Fig. I) will explain the process in treatment of the acid water.Acid mine drainage is treated with lime to increase the pH to 9.50. Metals in solution are precipitated as metal hydroxides and the 504 as calcium sulphate. The precipitate slurry is then aerated to convert ferrous iron to ferric iron, which is more stable for storage and disposal.The precipitate is next flocculated with a polymer flocculant and settled in the thickener to produce a sulphate/Hydroxide sludge and a final effluent discharged to the environment."

Jan 1, 1983

By J. C. Agarwal

Do large-scale projects in mining and smelting start up and achieve expected capacity on schedule? In most cases not. Regardless of worldwide location, company know-how, or financial backing, unforeseen delays occur. A comprehensive CRA study for the World Bank shows that delays are the rule, not the exception, in most mining and smelting projects. When delays are not factored into analysis and planning, financial projections are, literally, not to be believed. Returns on investment will seldom achieve their targeted level because of startup delays. This paper reviews the results of our analysis of startup of new mines, mills, and smelters; provides a detailed discussion of why delays occur in the smelters and refineries; presents the cash flow implications of startup delays; and discusses preventive measures that should be taken to avoid financial shortfalls,

Jan 1, 1983

By G. J. Gersbach

The Robe River Iron Ore Project began in 1962 when Cliffs International acquired mining leases in Western Australia's Pilbara Region. Initial reserves were proven and bulk ore samples sent to the U.S.A. for pilot plant testwork. Cliffs Western Australian Mining Company Pty. Limited (30%) manages the project in joint venture with Mitsui Iron Ore Development Pty. Limited (30%), Robe River Limited (35%) and Cape Lambert Iron Associates (5%).

Jan 1, 1983

By Richard E. Barrett

The relationship between coal characteristics and power plant performance has become a matter of increasing interest to utilities. This relationship can affect the value of coals, decisions as to coal washing, setting penalties for delivery of coal that fails to meet specifications, and justifying buying better coals (at higher costs) before public utility commissions. The study described in this paper was directed to identifying how coal characteristics impact on boilers and related coal and gas handling systems. TVA data for the period 1962-1980 was the basis for the study. Models were developed for boiler efficiency, boiler availability, and maintenance costs as a function of such coal characteristics as ash, sulfur, and moisture content and boiler age. Boiler load and maintenance efforts were considered as variables in some of the models, but were found not to be statistically significant. Although the results of this study are strictly applicable to only the TVA system, they can serve as guides or first approximations for other utilities.

Jan 1, 1983

By Frank E. Chase

Kettlebottoms are columnar masses of rock--the preserved casts of ancient tree stumps--embedded in coal mine roof strata (of which they are a part). Because unsupported kettlebottoms can detach from a mine roof without warning, they are a hazard to miners. The primary objectives of this investigation were (1) to better define and describe kettlebottoms and (2) to evaluate kettlebottom support techniques in terms of safety and effectiveness. A telephone survey of mine operators, interviews with Mine Safety and Health Administration (MSHA) personnel, and underground mine visits were conducted in Pennsylvania, West Virginia, and Kentucky. Information gathered during this investigation indicates that the size and frequency of kettlebottoms in mine roof are dependent upon past geologic events and biological processes active during the deposition of roof sediments. To ensure the safety of mine personnel, all undermined kettlebottoms should be supported. The roof should be bolted next to kettlebottoms less than 3 ft in diameter, close enough to allow a portion of a wood or steel header to be extended beneath each kettlebottom for support. Two bolts and a wood plank or steel strap should be employed to support kettlebottoms over 3 ft in diameter.

Jan 1, 1983

By C. Duke

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983

By W. W. Simpson

The Bureau of Mines conducted research to determine the effects of potassium trithiocarbonate (KTTC), a degradation product of potassium ethylxanthate (KEX), on flotation of chalcopyrite and molybdenite. Small amounts of KTTC were identified in fresh and aged solutions of KEX using thin-layer chromotography. Hallimond tube flotation tests on pure minerals showed that KTTC acts as a weak collector for chalcopyrite. Both KEX and KTTC tend to depress molybdenite, but the depression effect is easily overcome by addition of a small quantity of fuel oil. The results of the Hallimond tube tests were confirmed in batch flotation tests using a porphyry copper ore.

Jan 1, 1983

By Dave D. Ferris

Today the coal industry is beginning to use some very fundamental economic evaluations to determine the most economical circuit to produce a specified saleable product. The fundamental economic methods used are standard return on investment and net present value calculations. By utilizing these economical evaluations, one can justify a larger capital expenditure and realize more return for an investment over the life of a coal property.

Jan 1, 1983

By J. B. W. Bailey

The Noranda Horne smelter in Quebec, Canada has change considerably during the last two decades to accommodate varying custom concentrate receipts, closure of the Horne mine, better working conditions, environmental programmes, new technology and increased energy and labour costs. This paper highlights the reasons for changing the smelter from two calcine charged and one wet charge reverberatory furnaces fired by coal to a smelter using. tonnage oxygen oil, natural gas and coal in a single wet charged reverberatory furnace and a Noranda Process continuous Reactor. The current operation 1 described, including three major topics; the use of oxygen/fuel burners on the charge banks of the reverberatory furnace which has increase the smelting rate from 680 to 1100 tonnes of concentrate per day; the oxygen enrichment of the Noranda Process converting air to achieve smelting rates of over 1800 tonnes of concentrate per day; the converting of the mixture of 73 percent copper matte produced from the Noranda Process and the 33 percent copper matte produced from the reverberatory furnace.

Jan 1, 1983

By Keith T. Griffiths

INTRODUCTION The Empress Nickel Mine is situated forty-eight kilometres west of Kadoma in the Zhombe Communal Land of Zimbabwe. The mine came into operation in late 1968 based on a proved and probable ore reserve of twenty million tonnes. The initial production rate was 55 000 tonnes per month from underground. This was boosted to 85 000 tonnes per month in mid 1970 when the opencast operation came into production. The mining method at Empress is sub-level open stoping with main haulages mined at ninety metre intervals and sub-levels at eighteen metres. The extremely wide ore body of up to one hundred metres in width has necessitated leaving extremely large rib pillars and sill pillars in position to maintain mine stability and to act as regional support of the hanging wall. In early 1976 the opencast operation had reached its final economic depth and it was then necessary to increase underground production to 85 000 tonnes per month. Since a large portion of the ore reserve remained in both rib and sill pillars, it was necessary to embark on a positive pillar recovery programme. For this reason it was decided to introduce a sandfilling programme for the mined-out stopes and a modified system of sub-level open stoping with post filling of the lower stopes. ORE BODY GEOLOGY AND GEOMETRY The Empress orebody outcrop has a strike length of nine hundred and fifty metres on a north west - south east axis. It is a steeply dipping (65' - 75') tabular orebody of gabbroic rock which has been extensively altered. The north west - south east strike length of nine hundred and fifty metres on surface reduces to some two hundred

Jan 1, 1983

By V. Rajaram

Rock reinforcement systems are used in open pit and underground mines to stabilize the rock mass in-situ and provide safe working conditions. Significant progress has been made to date in the design and implementation of rock reinforcement systems to accommodate bad rock conditions and larger excavations. However, the rationale for the design of rock reinforcement systems remains essentially the same and can be categorized into three groups, namely 1. to create a beam of competent rock in stratified formations, 2. to resist sliding motion in jointed rock, 3. to passively support the superincumbent loads in highly stressed ground. Case histories of the rock reinforcement sys¬tems that illustrate these design approaches will be presented in this paper.

Jan 1, 1983

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of lead and zinc from 104 domestic mines and deposits. Fourteen primary lead and fifty-three primary zinc operations with in situ demonstrated resources containing 27.3 million metric tons (t) of lead and 53 million t of zinc were subsequently evaluated. Potentially 17.5 million t of lead and 2.4 million t of byproduct zinc could be recovered from 14 primary lead operations. Economic evaluations performed in constant January 1982 dollars determined a long-run total cost per pound of recoverable commodity. Including a 15-pct discounted-cash-flow rate of return (DCFROR), 59 pct of primary lead was potentially available at or below $0.32 per pound of lead. Potentially 40 million t of zinc and 5.6 million t of byproduct lead could be recovered from 53 primary zinc operations. Ninety percent of the recoverable zinc is potentially available from currently nonproducing mines and deposits, and a weighted average of their long-run total costs was determined at $0.98 per pound of zinc. At a breakeven (0-pct) DCFROR, these non producing operations had a weighted average long-run total cost of $0.58 per pound of zinc. Sensitivity analyses illustrated that operations that recover byproducts were most sensitive to fluctuating metal prices, producing operations were more sensitive to increased smelter treatment charges, and nonproducing operations were impacted most by the DCFROR.

Jan 1, 1983

By Floyd L. Prestridge

A test of a solvent extraction (SX) pilot plant featuring electrostatic coalescence has been performed by C-E Natco at the United Nuclear uranium mill in Church Rock, New Mexico. Operating in parallel with the United Nuclear SX system, the C-E Natco electrostatic SX pilot plant exhibited comparable extraction efficiency to the United Nuclear system which utilizes conventional mixer-settlers. The C-E Natco pilot, however, operated at much higher liquid loading rates and exhibited less communication between the aqueous phases of the extraction and stripping circuits.

Jan 1, 1983

By Roy E. Peterson

The Bureau of Mines conducted bench-scale research to evaluate materials which showed potential as low-cost reductants for use in the ironmaking industry. These materials were lignite, subbituminous coal, coal char, tree trimmings, refuse--derived paperboard, used crankcase oil, and peat. To compare their effectiveness, the materials were tested in the reduction roasting of nonmagnetic taconite and, except for oil and peat, in the reduction of iron oxide pellets to metallized pellets. Reduction was conducted in a 18-cm-diameter, rotary drum, which was externally heated in an electric furnace. Over 92 pct of the iron was magnetically recovered from a nonmagnetic taconite after roasting with any of the reductants, but greater quantities of reductant were required to achieve this when the waste materials were used. The fossil fuels were also more effective for metallizing pellets, although metallizations above 90 pct were also obtained with tree trimmings and refuse paperboard. However, refuse paperboard had to be frequently recharged to the furnace because it depleted rapidly.

Jan 1, 1983

By D. K. Steele

An 18-in-diam column water elutriator was designed, tested, and operated by the Bureau of Mines for recovering nonferrous mixed metals from automobile shredder rejects. The waver elutriator separated metals from nonmetals contained in shredded nonmagnetic rejects. The unit was constructed and integrated into a local automobile shredding operation. Nonmagnetic rejects from the automobile shredder were fed onto the surface of a column of rising water. Dense materials fell through the rising water and were collected as a sink product at the bottom of the column; medium-density materials were removed as an intermediate product in a water flow through a discharge port located between the overflow and sink; and light materials were immediately carried out in the overflowing water at the top of the column as a float product. Nearly 99 pct of the mixed metals were recovered from the nonmagnetic rejects as a 70-pct-metal concentrate. Other operating conditions yielded a 93.7-pct-pure-metal product resulting in a 93.1-pct metal recovery. Float rejects are combustibles, light plastics, foam rubber, and minimal amounts of coated and uncoated copper wire. The middling discharge contained mainly medium-density rubber, plastics, glass, rock, coated and uncoated copper wire, and frequently some thin-sheet stainless steel and wrought aluminum. Maximum metal recovery in the operating program was achieved using a water velocity of 52 fpm (650 gpm). Maximum purity was obtained with a velocity of 88 fpm (1,100 gpm). .Water was recycled through a 12,000-gal baffled clarifying tank. Entrainment water losses with the float and middling rejects averaged 50 gpt of reject feed. Records maintained by the shredder operator show a 34-pct increase in nonmagnetic metals recovery during a 1-yr operation of the water elutriator as compared to recoveries from a previously used air classification system.

Jan 1, 1983