Search Documents

By David A. Heitman

The Buick Concentrator is a highly automated operation which utilizes a process control system for continuous monitoring and control. The process control system development, installation, and application to the concentrator grinding and flotation circuits are presented in this paper. The design and implementation of analog field sensing instrumentation, a continuous on-stream X-ray analyzer, grinding and classfication circuit controls, and a recent digital process control system utilizing a centralized computer are discussed. Emphasis is placed on the project planning and installation of the digital control system including a presentation of future plans for continuing application of computer control.

Jan 1, 1982

By E. B. Jensen

The results of an extensive one- year test period of a nonelectric explosives detonating system led to the mine-wide adoption of this system at the Henderson Mine in early 1978. Since that time, extensive experience with nonelectric initiation has verified the earlier results which include the following benefits: 1. Increased blasting safety 2. Improved productivity 3. Cost effectiveness 4. High reliability At the present time, while electric blasting caps still experience a limited use restricted to trunkline initiation, all heading rounds as well as the longhole bell, undercut, boundary cutoff and raise blasting are detonated non-electrically. The primary blasting agent used is AN/FO, and primers are typically one of the following products (depending on application): PETN, semi-gelatin dynamites or a nonnitroglycerin water-gel slurry.

Jan 1, 1982

By Ralph B. Stevens

INTRODUCTION Underground fires continue to be one of the most serious hazards to life and property in the mining industry. Although underground mines are analogous to high-rise buildings where persons are isolated from immediate escape or rescue, application of technology to locate and control fire hazards while still in their controllable state is slow to be implemented in underground mines. Even in large surface structures such as hotels, often only fire protection systems which meet minimal laws are implemented due to the high cost of adding extensive extinguishing systems, isolation barriers, alternate ventilation, escape routes and alarm systems. Incomplete and ineffective protection occasionally is evidenced where costs would not seem to be a factor, such as the $211 million MGM Grand Hotel fire November 21, 19801. Paramount in increasing fire safety and decreasing the threat of serious fire is early warning followed by proper decision analysis to perform the correct action. However, very complex fire situations can be produced in structures such as high-rise buildings and underground mines simply because of the distances between the numerous fire-potential locations and fire safe areas. Other complexities arise when normal activities occur that emit products of combustion signaling a fire condition to a sensitive fire/smoke sensor. For example, the operation of diesel equipment or the performance of regular blasting can produce combustion products that reach the sensitive alarm points of many sensors2. Smoke detectors for surface installations provide fire warning when occupants are at a distant location or when sleeping, thus greatly reducing injuries and property damage. However, when installed in the harsh environments of underground mines, fire and smoke detection equipment soon becomes inoperative, unreliable, or requires excessive maintenance. The U.S. Bureau of Mines has performed many studies and tests to improve fire and smoke protection for underground mine workers3. This paper describes several USBM safety programs which included in-mine testing with mine fire and smoke sensors, telemetry and instrumentation to develop recommendations for improving mine fire safety. It is hoped that the technology developed during these programs can be added to other programs to provide the mining industry with the necessary fire safety facts. By recognizing fire potentials and being provided with cost-effective, proven components that will perform reliably under the poor environmental conditions of mining, mine operators can provide protection for their working life and property equal to that which they provide for themselves and their families at home. The basis of this report is two USBM programs for fire protection in metal and nonmetal mines4,5 and one coal program6. The data was collected beginning in May 1974 and continuing through the present with underground tests of a South African fire system installed at Magma Mine in Superior, Arizona, and a computer-assisted, experimental system at Peabody Coal Mine in Pawnee, Illinois. The conduct of each program was as follows: • Define the problem and its magnitude in the industry • Develop concepts to solve or diminish the problem • Review available hardware or systems approaches to fit the concepts • Install and demonstrate the performance of a prototype system through fire tests in an operating mine. MINE FIRE FACTS Whether in coal or metal and nonmetal mines, the potential severity of fire hazard is directly related to location. As shown in Figure 1, fire in intake air at zones A, B, C or D can cause contamined air to route throughout the mine quickly if not detected, isolated or rerouted. Causes and location of former metal and nonmetal fires are represented in Table 1; the cause and location of fatalities and injuries is shown in Table 2. Coal-related fires and their impact on deaths and injuries are graphed in Figure 2; their locations are described in Table 37. Significantly the table shows that the hazard to personnel was three times greater for fires occurring in shaft or slope areas, and the percentage of deaths and injuries was four times that of other areas. Number of Persons Affected A 129-mine sample indicated that from 8 to 479 employees per shift work in underground metal and nonmetal mines, and that deeper mines have larger populations, as shown in Figure 3. Coal mining relates similar employment, and a 16-state sample of 670 mines employing at least 25 persons shows the distribution in Figure 4. Drift mines accounted for 58 percent of the sample but employ only 45 percent of the underground workers.

Jan 1, 1982

By James H. Fletcher

Much data and experience has been accumulated, especially in the last 5 or 6 years, to show that modern roof trusses, both of the Birmingham type and the bolt-and-channel type, perform well to support certain kinds of coal mine roof. For some time now, roof trusses of the Birmingham type have been effective in controlling thick shale roof, which tends to sag and fall over a period of about eight weeks. These falls leave dame-shaped cavities which are reminiscent of the pressure arch theory of roof failure. Lately there has also been significant interest in supporting some longwall panel entries with channel and-bolt systems. These systems utilize two vertical center bolts and two 45 degree end bolts through a heavy gage channel. Both types of truss systems have long bolts, which require 8 to 9 Foot holes on a 45 degree angle, and point anchor resin bolts, which utilize a 2 or 3 foot rebar grouted in a thin annulus of polyester resin. Consequently, many coal mining people have been impressed with the very good anchorage characteristics and tensionability features of these systems. However, the same people have been proportionately dismayed to find that very often the most difficult part of introducing a trussing program to a mine is deciding on the machine specifications which determine the truss installation rate. The purpose of this paper is to indicate aspects of truss bolter design and use which are not shared by roofbolter design and its vertical pattern of bolts. Of the two types of drill units conventionally accepted, arm feed units and mast units, only one 15 judged suitable. While the arm feed unit offers low collapsed height with a long drill feed length, a great attribute for low seam use, it has not lent itself to being rolled over to a 45 degree angle. One reason for this inability is that many items which are conventionally mounted on the arm feed unit cannot be allowed to rotate with the unit. These items include drilling controls, tool Cray, lights, canopy or safety post, panic bar, and stab jack(s). If these items were independent of the arm feed drilling unit, they would have to be out of the way of the boom arms, links, and feed cylinder as the unit moves. To ease this problem, the arm feed unit can be made very short and even mounted across the machine. However, the resulting short feed length is undesirable. Several short drill steel extensions are required to drill a relatively long hole, making this procedure time-consuming as well as increasing the likelihood of drilling a crooked hole. Another reason for abandonment of the arm feed unit is that a very stiff drill guide (or "centralizer") is required to start the hole. Using the mast tilt control, the roof bolter operator will force the bit against the roof and will rotate the bit without feeding to cut sideways into the roof to form a hole face. Omission of this step often results in the skidding of the bit toward the rib. To date, no such sturdy drill guide has been designed for an arm feed drill unit. The mast style unit has been the most successful design for angle drilling. It is easily rolled over to a 45 degree angle or to 90 degrees and, on single head models, often has been made to roll through 180 degrees. The mast style is compact, in plain view and is easily fitted with heavy duty manual or hydraulically operated drill guides. It can be mounted directly on a machine chassis, or onto a swinging boom, or onto a slider arrangement in a broad variety of configurations which will accommodate controls, tool trays, stab and roof support jacks, lights, canopies, and panic bars. The only significant difficulty with mast drilling units occurs in lower mining heights when desirable low mast height is accompanied by undesirable short feed length. While the lead extension in the drill string can be as large as the mining height will allow, a short feed length will permit only the use of shorter middle extensions and drivers, and perhaps will. require the use of two different length wrenches. The associated problem is the relatively short distance from the drillhead to the drillguide. This distance is further shortened when raising the drillhead to get the bit to the roof. One might keep longer lead extensions on the machine; drill a vertical pocket for the bit, starting the angle hole at this pocket; or modify the mast. If the mast is made so that the distance from the drillhead to the drillguide remains constant while the mast extends, after which the drillhead travels up the mast, the shorter mast can be made to start the hole more easily. However, short teed length will still result in longer drilling time. It is obvious from these points that a proper choice of mast is simply the highest one which will be moved easily in the given mining height. This, of course, goes against the grain of most experienced coal mining people who realize that a relatively small decrease in mining height can create a problem correctable only with the purchase and installation of shorter masts. If the mining

Jan 1, 1982

By A. E. Raddatz

The U.S. Department of the Interior, Bureau of Mines, is investigating methods for recovering tungsten from domestic resources. A calcine-quench-leach (CQL) technique was developed for the extraction of tungsten from the Golconda, Nevada, hot springs ores. The deposit contains disseminated tungsten, which cannot be beneficiated by conventional techniques and must be treated by hydrometallurgical methods. The CQL procedure consists of calcining the ore at 900° C for 3 hr, quenching in a solution containing 1.5 parts of NazCO3 and 1.5 parts of NaOH per part of WO3 in the ore and at a solution- to-ore ratio of 3 to 1, leaching at 200° C and at 250 psig for 3 hr, and filtering and washing the residue. A series of closed-circuit batch tests showed that 92 pct of the tungsten was extracted from a sample containing 2.32 pct WO3. The pregnant solution contained 11 q of W03/1.

Jan 1, 1982

By R. M. Schuster

This study attempts to compare the costs of transporting coarse coal by pipeline, versus the more conventional use of belt conveyors. Hydraulic conveying of crushed (not pulverized) coal has not had widespread commercial acceptance. However, there is little doubt that the technology is available, so that, should this method be proven economical for a given application, implementation of this technology will become more acceptable. Hydraulic transport by pipeline between the mine stockpile and the coal preparation plant, for distances normally considered practical for an overland belt conveyor, should be an ideal application. In this application there is no need for dewatering facilities at the receiving end of the pipeline, because, the receiving screens at the plant serve this purpose. Further, clarified water from the preparation plant can be recirculated back to the mine, a plus for water resource and environmental considerations.

Jan 1, 1982

By E. A. Devuyst

Metallurgical processes involving the use of cyanide such as gold cyanidation, metal plating and flotation, generate effluents containing cyanide and cyanide in complex combinations with heavy metals in quantities exceeding those regarded as being safe for discharge into streams. A new process for destruction of free and complexed cyanide and related-species in wastewaters has been developed at the Inco research laboratories using sulfur dioxide, air and lime. High reaction rates are obtained in the presence of a small amount of copper which acts as a catalyst. Cyanide species can be reduced to as low as 0.1 mg/L in a very short treatment time. Examples of treatment of gold mill effluents and barren slurries, plating rinse waters and flotation liquors or tailing slurries are given.

Jan 1, 1982

By Tsutomu Yanagase

Non-ferrous smelting industry in Japan often had the severe problems about the over production of sulfuric acid. There has been such a closed relation between amount of sulfuric acid from non-ferrous smelting industry and the products of copper, zinc and lead metals that the production of one ton of copper accompanies three tons of H2S04. When the proper balance exists in both markets this situation certainly brings bigger profits. In Xining and Metallurgical Institute of Japan the research commitee concerned with the fixation process of sulfur in non-ferrous smelting industry was established in 1977 and continued the activity for four years untill 1981. This paper will introduce some of the activities involved in the report published by the committee.

Jan 1, 1982

By Kevin J. Ashley

Coal is deposited at a mine site in several thin seams which outcrop in rolling hills and dip at about 8° to the northeast. The deposit is located in the northeast area of the State of New Mexico in the Southwest of the United States. A drilling program was undertaken and was quite irregular. Not all of the seams appear in all of the drill holes. Some of the holes did not go deep enough, while others were drilled below the outcrop of some seams. Occasionally a seam would pinch out and not be seen in a drill hole. Also, the outcrops of the seams are buried in many places by several feet of alluvium. All of these factors make correlation of the seams between drill holes difficult. The drawing of cross sections in three directions and at many locations across the mining area have been necessary to assure the accuracy of the input data.

Jan 1, 1982

By Nicholas T. Esposito

An advanced coal preparation plant has been built at Homer City, Pennsylvania, by Pennsylvania Electric Company, a subsidiary of General Public Utilities Corporation, and New York State Electric and Gas Corporation, as an alternative to utilizing flue gas desulfurization technology to meet the Federal Environmental Protection Agency and the Pennsylvania Department of Environmental Resources air quality emission regulations of 4.0 lb S02/106BTU for the two (2) existing coal-fired generating station Units No. 1 and No. 2, and a 1.2 lb S02/106BTU for the new Unit No. 3. The coal preparation plant is designed to process 5,200,000 tons of run of the mine coal annually and has a design capability to process 1,200 tons per hour via two (2) equal capacity 600 tons per hour preparation circuits.- The plant is designed to produce multi-product coal streams consisting of a middling product of medium ash and medium sulphur content, which is environmentally compatible to support operation of the two (2) existing generating Units I and 2, and a deep cleaned, low ash, low sulphur coal product capable of environmentally supporting the ambient air quality requirements of the new Unit 3 generating facility. The waste product from the process consists of high ash, high sulphur reject material. The process has the acronym MCCS (Multi-Stream Coal Cleaning System).

Jan 1, 1982

By T. Hayashi

A sophisticated process of extracting ultrafine sulfide mineral particles of under 1µm size suspended in clay slurry has been developed through studies of electrochemical properties of particle surface. Experimental procedure and data of the process applied to some clay ores containing sphalerite and pyrite, and molybdenite and other sulfide minerals are reported. Discussions concentrated on the function of process reagents, particularly on various modifying reagents, and on the effect of dispersed or flocculated state of ultrafine particles in slurry which affect significantly the performance of the process.

Jan 1, 1982

By D. W. Evans

Mine subsidence problems due to coal extraction have occurred in a number of areas throughout the United States. Depending on the local geology, the depth of the mined seam, the type of mining method employed for extraction, and other related factors, subsidence can result in anywhere from slight displacements to a total loss of ground. These conditions can have serious consequences on the health and safety of the people living above the mined areas. A number of methods exist to provide support for the ground overlying mines. All of these methods employ some mechanism for providing additional support to either the roof of the mine or the sides of the pillars. Since failure usually occurs due to overburden stresses which are transmitted to the roof and pillars, these methods employ techniques to counteract stresses induced due to the coal extraction. The applicability of any particular method will depend on the availability of backfill material, the areal extent of the affected area, and of course, the cost. The primary use of coal ash for subsidence control has been as a backfill material for the stabilization of large areas. Large scale backfilling projects for subsidence control have been performed in Rock Springs, Wyoming, Wilkes-Barre and Scranton, Pennsylvania, and in Fairmont, West Virginia. Some of these projects have utilized sand, as well as, coal ash as backfill material. Much of the backfilling work performed in the United States has been done in an effort to control mine subsidence in abandoned mines. South Africa, on the other hand, has used backfilling extensively both for ash disposal and to increase extraction in active mines. The utilization of repetitive fill and mine techniques has resulted in extraction increases of as much as eight percent in shallow mines and as much as twelve percent in deep mines.(1) The coal ash injection system which can be used for backfilling depends largely upon whether the mine voids are dry or submerged. For dry mines, hydraulic or pneumatic conveyance systems can be used, while submerged mines are limited to backfilling by hydraulic methods. The use of coal ash as a backfill material has a number of advantages, such as: 1. Coal ash is available in areas throughout the United States and in many instances is conveniently located near areas requiring backfilling. 2. Coal ash is available in significant quantities since many coals when burned will result in about 15 to 30 percent ash by weight. 3. Coal ash as backfill is, in many instances, the most economical alternative fill material. Due to the costs associated with above ground disposal, power companies will often times give the material away to lower their overall operating expenses. 4. Coal ash is usually pozzolanic in nature, that is, this material results in cementitious bonding within the backfilled matrix of material.

Jan 1, 1982

By Neil D. Policow

Dewatering of the fine clean coal fraction, - 28 mesh (595 microns) represents one of the most difficult and costly separations in typical plant circuits. Since 1969, the Screen Bowl Centrifuge has offered an economical alternative to filtration/thermal dryer combinations. The performance of Screen Bowl Centrifuges has been continuously modified and improved to dewater not only coarser coals, but also today's variety of ultrafine material. Actual test comparisons with alternative methods show the Screen Bowl Centrifuge to be most cost effective and efficient when all factors are considered.

Jan 1, 1982

By David C. Grant

During in situ uranium mining using ammonium bicarbonate lixiviant, the ammonium exchanges with cations on the ore's clay. Mter mining is complete, the ammonium may desorb into post-leach ground water. For the particular ore studied, other chemicals (i.e., uranium and selenium) which are mobilized during the leach process, have also been found in the post-leach ground water. Laboratory column tests, used to simulate the leaching process, have shown that aluminum chloride can rapidly remove ammonium from the ore and thus greatly reduce the subsequent ammonium leakage level into ground water. The aluminum chloride has also been found to reduce the leakage levels of uranium and selenium. In addition, the aluminum chloride treatment produces a rapid improvement in permeability.

Jan 1, 1982

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

By Jan Wolski

Today's rapidly shrinking world requires a common language of measurements, a consistent system which could be used by everyone. The S.I. system of units is generally accepted as such and is already in use by a great majority of nations in the world. The change to S.I. units is also slowly taking place in U.S. engineering practice. The transition period is difficult and long because it takes time to get familiar with the new system, to start "feeling" values in new units. Instruments, formulas, computer programs, survey grids, etc. have to be converted or exchanged. The transition period should be used not only for substitution of units, but also for rationalization of presently used calculation methods. This paper examines the major parameters of mine ventilation from the above point of view and discusses a system which is much simpler and more consistent than the American Unit System still in use in the United States. In October 1979, the Society of Mining Engineers of AIME decided to introduce the S.I. unit system in all its publications including the periodical "Mining Engineering", and since February 1980 the system has been used consistently, not only in SME publications but in all conferences and meetings organized by this Society. The authors have no intention of explaining the details of the S.I. system in general. Any reader can find this information in many available publications and conversion tables, and in particular in the ASTM Standard for Metric Practice, E380-79. A comparison is made between various units used in mine ventilation from the past and those presently in use. This will allow an easy translation from one system to another, important when reading publications from abroad. S.I. and customary U.S. formulae are shown side by side for easier visualization of similarities and differences. Recommendations for the necessary steps in order to switch from American to S.I. units conclude the paper.

Jan 1, 1982

By Shawn T. Sorrell

Phillips Coal Company (PCC) submitted the first surface mine permit application under the Office of Surface &lining approved regulatory program of the State of Louisiana. This application for the Oxbow Lignite Surface Mine which is located approximately 64 kilometers (40 miles) southeast of Shreveport, Louisiana was submitted in March 1981. The State of Louisiana Office of Conservation, Surface Mining Division, assigned this application number LSM-1, indicating it is the first one submitted in Louisiana history. The permit area for the Oxbow Mine encompasses 6,251 hectares (15,627 acres). Of this total permit area, 5,862 hectares (14,656 acres) were classified by soil type as prime farmland by the U.S. Soil Conservation Service (SCS). Prime farmland acreage in the permit area became a major central issue in our early planning stages and throughout the permitting process of the Oxbow Mine, due to the magnitude of acreage involved.

Jan 1, 1982

By N. B. Strydom, H. H. E. Schroder, A. van der Linde

This paper describes a study of the destination of the mercury that is present in the ore during the recovery of gold. It was found that over 96 per cent of the mercury passed through the process untouched. A small amount finds its way into cyanide solution, and is concentrated with gold in Zinc dust as Merrill precipitate. When the precipitate is calcined, the mercury is driven off and finds its way into the atmosphere. However, dilution of the stack gas in the atmosphere appears to be sufficient to prevent hazardous concentrations arising at ground level. No other significant concentrations of mercury were found at any stage of the process. The amount of mercury lost to the atmosphere by this mechanism appears to be less than 200 kg per year throughout the gold-mining industry in South Africa. Virtually no mercury vapour could be detected in the air in the smelt-house. Slight increases in mercury concentrations above background level were observed in soils around the reduction plants and in the discharge or return waters, but no environmental stress is anticipated from these increases.

Jan 1, 1982

By R. L. Rickel

The Bureau of Mines, as part of its minerals environmental technology research, conducted a study of mine waste tailings disposal. Part of the investigation evaluated the sand bed dewatering technique for disposal of alumina mini plant tailings as a means to increase consolidation rates and contain effluents. The technique employs a bed of sand resting on an impervious bottom. The tailings slurry is impounded over the sand layer and is dewatered through bottom drain piping. The study employed a single 10-ft-high, 6-in-diam, clear polyvinyl-chloride (PVC) column, and thickener wastes from the acid leaching of calcined kaolin clay. Results showed a consolidation rate of 41 in in 186 days for a total volume reduction of 37 pct. Sand bed dewatering was an efficient technique for solid consolidation and effluent containment when compared with data obtained from other dewatering studies.

Jan 1, 1982

By E. L. Smith

The development of larger size flotation machines, which started in the 1950's and 19601s, is still proceeding. The largest mechanical flotation machines available today have unit volumes in the range of 38 to 42 m3 (1,350 to 1,500 cft). In fact, the motivating forces of increasing capital and energy costs and decreasing ore grades, which created the need for large flotation cells, not only still exist, but are becoming more critical. This paper reports the development of an improved mechanism for these large flotation machines. The starting point in the development of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1982