Search Documents

By Raphael D. Schilz, Michael F. Dunn, Edward D. Thimons, Francis S. Kendorski

During a mine fire or other emergency, it may be desirable to reverse the air flow in order to provide an escapeway or to control a fire. Also, in colder areas, the air flow may be reversed to prevent ice build-ups. When reversing main mine fans, the operator usually does not know what operating characteristics of flow and pressure to expect. Laboratory testing of vane axial main mine fans has been completed in order to establish forward and reverse performance characteristics under controlled conditions, with the results presented here. Preliminary tests under field conditions have also been conducted. The data obtained suggest that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. There is also evidence that reverse performance can he predicted for a family of blade angles in a given hub to tip ratio. In general, the air quantity delivered by the fan is 30% to 60% less in reverse than when operating in the normal forward mode.

Jan 1, 1982

By D. J. Lachel, Douglas E. Hansen, Bruce Kennedy

The very high cost of exploration and development for new mines requires that a carefully planned, complete, and technically competent geotechnical evaluation be applied to the ore body and the surrounding rock. The ground conditions must be predetermined sufficiently so that, during the development and exploitation stages, unexpected conditions will be of minor consequence. Ground conditions are a major factor affecting the cost of excavated items such as shafts and inclines. For example, shafts cost less to sink in tight dry ground than in highly pervious ground below the water table, with all other factors being equal. The proper mining methods also is dependent upon the ground conditions. Bad ground for room-and-pillar mining may be ideal for caving methods; whereas, ideal ground for room-and-pillar mining would be extremely difficult for a caving operation. To do a proper engineering design, the parameters of strength, deformability, and permeability must be determined, in addition to the loads that will be applied as a result of the mining activity. The required degree of accuracy for each parameter depends upon the individual case. For example, the strength of massive rock in which openings of small cross-sectional area are to be driven at shallow depths needs to be resolved only within several thousand kilopascals (pounds per square inch). Under such conditions, the rock strength is not likely to be of great economic importance unless the rock is very weak. Large openings at great depths require a much more accurate appraisal of rock strength and deformation characteristics. Ground water conditions are important at any depth. Today, a number of techniques exist for evaluating conditions before opening up the ground for development. These techniques and their applications are described in more detail later in this text. The evaluation of ore body ground conditions should start at an early stage, as soon as the deposit has been proven viable for a mine. Economic geology investigations mainly serve to define the value and limits of the ore deposit. To do this properly, the geology of the site is determined in at least as much detail as is necessary to define the "controls" for the ore body. The ground-condition evaluation must determine the engineering properties of the ore body and the surrounding material. This includes the structural geology as it relates to rock strength; i.e., the frequency, extent, and orientation of discontinuities such as faults, joints, bedding, etc. Ground water conditions also must be determined. It is important that the detailed geology of the site be determined at an early date. Reasonable geotechnical parameters must be established during this time period, so they can be used in mining model studies that include both physical and mathematical models. The ultimate goal bf-the geotechnical evaluation is to predict the ground behavior as the excavations are made and how the ground behavior will affect the safety and economic well-being of the mine. The formulation of a ground-condition evaluation program should be planned carefully to determine the particular geotechnical parameters only in as great a detail as will have a bearing on the mine design. For instance, it is not necessary to make numerous triaxial tests in strong rock when the mining will be conducted within a few meters (feet) of the surface in a regime of gravity loading and an absence of tectonic stresses. Similarly, it is not necessary to invest large amounts of time and effort in the determination of joint strengths if the orientations of the joints are such that the failure could not occur along them. Generally, the determination of ore body ground conditions can be divided into four main steps: 1) The general and structural geology of the site must be determined; this is determined primarily during the economic evaluation. 2) The material behavior characteristics of the deposit and the vicinity must be determined. 3) The ground water hydrology of the deposit and the vicinity must be determined. 4) Miscellaneous ground support considerations must be established. Gross features are defined first, followed by a series of increasingly detailed investigations. Specifically, the geology study should start by utilizing techniques such as remote sensing, topographic map interpretation, geologic mapping, etc. After the gross features, such as major faults, have been delineated, the studies are directed toward defining the more detailed elements of jointing, rock strength, ground water hydrology, and other characteristics. This information is used to formulate an assessment of the strength of the ore body and the surrounding rock. Finally, all of the gathered information is integrated to make an assessment of the rock behavior in relation to the types of openings, the excavation methods, the support requirements, etc., that should be used for the rock conditions that are present. The mine design and the geotechnical assessment should be an iterative process. General conclusions about the rock conditions will dictate a type of mine plan. The specific mine plan then should be modified by specific geotechnical considerations. For example, an initial assessment may conclude that the ore body is strong and that a strong rock unit is present over the ore body. Thus, one definite possibility is to mine the deposit by room-and-pillar methods. However, subsequent investigations may reveal faults through the deposit, requiring relocation of the mine openings so that pillars and other structures are in sound rock. In other words, the final mine plan should be compatible with the geotechnical aspects of the ore body.

Jan 1, 1982

By William Lyman

GENERAL DESCRIPTION Shrinkage or shrinkage stoping refers to any mining method in which broken ore is temporarily retained in the stope to provide a working platform and/or to offer temporary support to the stope walls during active mining. Since ore "swells" when broken, it is necessary to shrink the muck pile a corresponding amount by draw¬ing some of the broken ore out as the stope is advanced-hence the name. Broken ore retained during stoping is drawn out after the stope has reached its limits. The stope may be left empty or may be filled with waste contemporaneous with, or subsequent to, the final draw. Traditionally the method implies conventional overhand stoping methods with miners working between the muck pile and the stope back, in a space which advances updip with mining and is maintained by balanc¬ing "swell" with "shrink." The shrinkage classification is also applicable to so-called "semishrinkage" methods in open pillar-supported stopes where broken ore is temporarily retained as a working platform but offers no wall support; and to various blasthole shrinkage methods which utilize broken ore temporarily retained in the stope for wall support, but which do not require miners to work from muck pile in the stope. The method is generally applied to steeply dipping veins of strong ore between strong walls. APPLICATION Geometry The geometry of a shrinkable vein is described in terms of dip, width, and regularity along dip. Overall strike and dip dimensions and irregularities along the strike generally impose no restrictions on the method. Dip is ideally 1.2 to 1.5 rad (70 to 90°). As dip falls below 1.2 rad (70°), the shrinkage draw begins to strongly favor the hanging wall side, thus leaving a poor working platform for conventional overhand work. This is particularly true in relatively wide stopes. The sup¬port afforded to the hanging wall also diminishes with decreasing dip, reaching nil as the dip approaches the repose angle of broken ore. Dips below 0.78 to 0.87 rad (45 to 50°) are not generally shrinkable except by open stope "seinishrinkage" methods. Minimum mining width is fixed by working space requirements in the stope-generally about 1 m. Shrink¬age in narrower veins requires that waste rock from one or both walls be broken with the ore and the attendant dilution accepted to achieve the minimum width. Nar¬row stopes are less suitable, encouraging hang-ups and bridging of broken ore, with the attendant problems of erratic draw and incomplete recovery of broken ore. Maximum practical width may be 3 m or less to over 30 m, depending upon the competency of the ore and its ability to stand unsupported across the stope back. This is a vital safety consideration in conventional over¬hand stopes, but is much less of a factor in blasthole shrinkage methods. Very wide veins and massive ore bodies have been mined by transverse vertical shrinkage panels separated by transverse vertical pillars which are either abandoned or recovered later by other methods. Regularity along the dip is a prerequisite of shrink¬age as there must be no serious obstruction to the flow of broken ore downward through the stope to the sill level. Gentle rolls along the dip are acceptable if the local footwall dip everywhere exceeds 0.78 to 0.87 rad (45 to 50°). Off-dip hanging wall and/or footwall splits can generally be mined selectively from a conventional shrink stope as they are encountered without ad¬versely affecting subsequent continuation of shrinkage mining updip on the main vein. Vertical offsets or major rolls along the dip which cannot be "smoothed over" generally require that a sublevel be established with new draw control development. Blasthole shrinkage methods are much less flexible (and thus less selective) in their ability to accommodate any of these irregularities. Ground Conditions The wall rock must be strong enough to stand with the minimal support afforded by the dynamic mass of broken ore in the stope. During active mining, local sloughing from the walls is restrained, but the broken ore affords little, if any, useful resistance to closure of the stope walls. Such squeezing, if present, may bind up the stope and cause the loss of much ore. Pillars left between and/or within stopes are effective in preventing closure but reduce overall recovery. Walls may be re¬inforced by bolting after each stope cut in conventional shrinkage but not in blasthole shrinkage. Ore in place must be strong enough to stand with no natural support across the stope width, although tem¬porary artificial support or reinforcement may be used locally in conventional stopes. Some spalling or sloughing is permissible in blasthole shrinkage as men are never present in the stope. Physical and/or mineralogical characteristics of the broken ore may impose restrictions on stope design and/or operational plan¬ning, and may even preclude the use of shrinkage al¬together. Examples include: ores which, when broken, are cohesive or which tend to pack or cement together under the influence of ground water, wall pressure, and/ or chemical reaction. Such conditions precipitate er¬ratic draw during mining and often result in difficult and/or incomplete final draw; pyritic ores which oxidize very rapidly in the stopes and may generate heat, imposing a fire hazard by spontaneous combustion; sulfide ores which oxidize sufficiently in the stopes to adversely affect mill recovery by flotation; and ores (es¬pecially those containing uranium minerals) which ex¬ude radon gas and thereby impose ventilation constraints on stope design. In most cases these problems can be minimized by limiting the size of stopes, by minimizing the duration of mining activity in each stope, and by promptly drawing each stope empty following comple¬tion of mining.

Jan 1, 1982

By J. P. Van Dillen

Continuing interest in processes that will effect separations in the fine particle size range has prompted intense interest in the use of high gradient magnetic separation (HGMS) for beneficiation of uranium ores. Some of the uranium minerals are paramagnetic and hence are amenable to concentration by HGMS. This paper presents a brief review of the problems associated with uranium ores beneficiation, a description of the HGNS process, and the effects of the parameters--pulp velocity, field strength, matrix loading and magnetic field gradient on product recovery and grade. Unsatisfactory separation of uranium minerals by HGHS is related to ore specific properties such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix and interference of micron sized slimes. Experimental techniques to identify and resolve some of these problems are outlined.

Jan 1, 1982

By Richard Klimpel

The laboratory ball mill grinding of coal/water slurries is described for three coals. Emphasis is placed on the measurement of specific rates of breakage for various operating conditions. Corresponding rheological information is also presented based on data collected using a rotational viscometer. A rheological explanation of the influence of various slurry fluidity conditions on the specific rates of breakage is presented. This rheological approach has proved useful In both the identification of suitable chemicals for increasing breakage rates in coal/mineral slurry grinding and in the plant scale implementation of dense slurry grinding systems.

Jan 1, 1982

By Jalal Vakili

In designing very large excavated slopes which are becoming increasingly common in both mining and civil engineering projects, the most important decision of the engineer is the selection of a slope angle. The purpose of the geotechnical study of the slope is to ensure reasonable stability of the slope in the most economical way. Because the rock mass composing each slope is unique, there are no standard solutions for slope stability analysis. A practical solution is formulated from the basic geologic data, engineering properties of the rock, geometry of the slope, and ground water observations. Stability analysis consists of analyzing the forces causing and resisting slope failure. There are several methods of slope stability analysis. The limit equilibrium method evaluates the overall stability of the sliding mass just on the verge of slip, using some or all of the three equations of static equilibrium of a plane problem. The stress-strain relationships of the rock mass are not considered. Method of analysis include the assumption of the shape of the slip surface. Peterson (10) introduced the Swedish method of analysis in 1916, which is based on cylindrical sliding surfaces. Fellenius (4) in 1926 extended this method and introduced the method of slices. This method was refined by Bishop (I) in 1955 and later used by Morgenstern and Price (8) in 1965. In many cases layers of extremely soft strata or strata weakened by neutral stress cause failure to take place by translation along plane of weakness instead of by rotation on a circular surface. In this paper, a slope with a horizontal layer of weak meterial is selected for analysis. This is a usual case for open pit lignite mines where lignite seam may be non-cohesive and 'weaker than the overburden rock or a soft clay layer underlies the seam. It is also a common case of rock fill dams supported on a foundation stratum of clay where the strength of the clay layer is less than that of the rock fill. It is shown that utilizing this method, the location of potential failure surface and the value of the minimum factor of safety can be calculated directly and the trial computations of factors of safety for a number of assumed failure surfaces are not necessary.

Jan 1, 1982

By Thys B. Johnson

This paper presents a new algorithm for solving the Controlled Flow Mine Ventilation Problem in an optimal manner - minimum power consumption. The use of booster fans and restrictions on the locations of ventilation regulators are dealt with in a straightforward manner. This new approach is based on a common Operations Research algorithm for which there are many fast computer programs available.

Jan 1, 1982

By Richard L. Bullock

At the beginning of the previous chapter, variation in the types of room-and-pillar stopes were briefly identified so that the reader could begin to understand the extensive application of this mining system. These same variations will be reviewed and elaborated upon in this chapter while discussing the methods by which the material is extracted. FULL-FACE SLICING BY DRILLING AND BLASTING When the entire mineralized thickness is taken in one pass of mining, it is known as full-face slicing. There is no mineral of economic value intentionally left either in the floor or the back. Theoretically, there is no limit as to how high the face could be in a single pass. But there are practical limitations to equipment size, pillar stability, and control of local loose slabs on the face, roof, and pillars that dictate current practices. The range of face height of the 15 typical room- and-pillar mines covered in Table 8 (Sec. 1, Subsec. 7) from the Dravo report, 1974 was 1.7 m (5.5 ft) to 9.8 m (32.1 ft), the average being 5.2 m (17.1 ft). In the Gaspe copper mine, Murduchville, Que., the drill jumbos were constructed with an extendable tower for full-face mining up to 15.2 m (49.9 ft) if necessary. However, a more common practice at that mine is to take the ore in multiple slices (Hall, 1959). In many metal mines the normal practice when starting stoping is to drive a single development drift into the ore zone a distance that will allow at least four or five rooms to be opened on each side of the initial drift. Since this opening will probably serve as the main haulage drift, it should be kept as straight and as level as possible. As to the other criteria for the stope developments, it might be well at this point for the mine planner to review the remarks presented earlier (Sec. 1, Subsec. 7) on drifts, entries, and crosscuts for production. After the initial drift is driven, it should be slabbed to the full room width if it is not that wide already. Next, the future pillars should be marked on the ribs and the rooms driven between them. If the ore extends beyond the length of the initial drift and is to be mined in the normal sequence of mining, care should be taken in a random room-and-pillar system to see that the extension of the initial roadway remains straight. If pillar "spotting" is left to the shift foreman or to the miners, they probably will not realize the importance of maintaining a uniform pillar line next to the roadway, and of keeping the line straight. Invariably, a pillar will end up in the middle of the future drift extension resulting in a "dogleg" in a possible main haul- age road. While this error is not catastrophic, too much weaving in and out of pillars will certainly slow down future production haulage and needlessly increase costs. Face or Breast Drilling and Blasting Practices To drill and blast the initial advances into the rock, usually some form of cut pattern must be used. In room-and-pillar mining, when a pattern is drilled in a face and that face is the only exposed surface to which all of the rock must be broken, the pattern is known as a "face round" or "swing." The face to which the rock must be broken is referred to as a "free face." Thus the most common way to advance a room into virgin rock with only one free face is by drilling swings. If, after breaking around a pillar, taking down back, or taking up bottom, there is a second (or third) face exposed, a group of holes drilled nearly parallel to a free face and breaking to it is known as a "slab round" or "slabbing." In some mining districts it is also known as "slashing." Obviously, because two faces exposed offer less resistance to fragmentation than a single face, slabbing requires less drilling and fewer explosives than required to break the same tonnage with the same degree of fragmentation with swings. Therefore, it behooves the driller (or supervisor) to plan the combination of

Jan 1, 1982

By J. Wong

We report a successful use of x-ray absorption spectroscopy to probe the chemical and structural environment of trace elements in coal. When applied to vanadium in coal, it was found that vanadium exists in at least two environments: a trivalent site 6-fold coordinated by oxygens at ca. 2.0~ and a tetravalent site 5-or 6-fold coordinated also by oxygens, one of which forms a short V=O bond at ca. 1.6a. No evidence of nitrogen (porphyrin)1'or sulfide environment was found. It was also found that the vanadium environ-ments in the raw coal did not survive unchanged in a liquefaction process. These findings have implications for coal cleaning processes and for trace element release into liquefaction process streams.

Jan 1, 1982

By Christian F. Baiz

Industrial minerals can have similar financing requirements to those needs of metaliferrous and coal mining projects. Although, one may see many similarities in the fundamentals of the various risks that must be evaluated in lending to any specific project, one of the outstanding differences is the understanding of the many different markets that these industrial minerals represent. There are in excess of 30 principal industrial minerals ranging in terms of annual production from the largest quantity such as sand and gravel, to possibly the smallest quantity of production of a legitimate industrial mineral which may be defined as industrial and rough gem diamond. If we assume that it is necessary to finance independent projects of ore bodies of industrial minerals for development, the financing techniques are similar to the fundamentals that we would use for financing coal projects or metaliferrous deposits. Therefore, let's begin by redefining project financing in the traditional banking or private sector area, and then in the later development of this paper, we will apply these techniques to industrial minerals in general and cite it with several specific examples.

Jan 1, 1982

By Robert L. Grayson

An application of goal programming (GP) in evaluation of proposed purchases of major mining machinery is presented. It incorporates historical operating data compiled on mechanical delays to production time. The goal programming technique, which is an extension of integer programming, is used to maximize an objective function. The objective function combines the capital budgeting evaluation methods of net present value, payback period, profitability index, and total net earnings as goals weighted according to a management preference. The GP method gives an optimal solution to a multiple-goal problem. A sensitivity analysis is performed to determine the effect of an increased production forecast or a tightened budget on proposal selection.

Jan 1, 1982

By H. J. Sutherland

This paper reviews the results of the subsidence research prop ram at Sandia National Laboratories. The manuscript highlights the following: the application of empirical methods (profile functions) to the subsidence above longwall panels in the U.S.; the use of the "rubble model" to describe the behavior of broken strata as it distends when it falls to the Mine floor (or top of the rubble pile) and then is subsequently compacted as it is loaded by overlying elements of strata; and, the application of physical modeling techniques (centrifuge simulations) and numerical techniques to study the failure mechanisms in highly structured stratigraphy. The capabilities of the latter two are illustrated ')y comparing their predictions to the results of a field case that has complicated stratigraphy.

Jan 1, 1982

By Roddick F

From its mining lease at the northern end of Cohens Reef at Walhalla in the North Gipps- land mountains, the Long Tunnel Extended Gold Mining Company produced 13,695kg of gold, which at 1982 prices represents a value of about $140 million. In the period 1885 to 1908 the mine was one of Australia's principal reef gold producers, being top Victorian producer in six of these twenty-four years. Prior and subse- quent occupants of the lease produced an addit- ional 160kg of gold. The Extended and the other mines on Cohens Reef whilst contributing importantly to the financial resource of Victoria, were the sole important support for the substantial town of Walhalla that had grown up around them. When the mines closed, Walhalla gradually reduced from a bustling developed town to the present attractive mountain village so favoured by tourists.

Jan 1, 1982

By G. J. C. Young

The paper describes the replacement of a conventional filtration, clarification and zinc precipitation plant by a carbon in pulp (CIP) electrowinning plant, with the objective of improving the recovery of gold from cyanide leached, acid plant calcines. The discussion covers the early laboratory studies to the design and erection of the full scale plant. Particular emphasis is placed on the problems encountered with commissioning and the strategies which were employed to solve them.

Jan 1, 1982

By Z. C. Song

[THIS PAPER WAS TRANSLATED FROM CHINESE TO ENGLISH BY S. S. PENG, WEST VIRGINIA UNIVERSITY] Immediately after coal extraction, the pressure that causes the movement of the surrounding strata is called mine pressure. Through the strata movement, certain features such as supports taking load arise. This is called "manifestation of mine pressure". The existence of mine pressure is ab¬solute whereas its manifestation is relative and conditional. The visible movement of the surrounding strata occurs only when the applied pressure exceeds the plastic breaking strength. Me support begins to take load only when it offers resistance to the strata movement. The key to investigating mine pressure and its control hinges on understanding the rules and conditions for the manifestation of mine pressure. Since the face moves continuously, the mine pressure and its manifestations are also constantly changing. 'Therefore, it should not only emphasize to obtain its instantaneous magnitude, but more importantly the rules of development changes and their relations to the movement of overlying strata. Once this is resolved, one can estimate the movement of the overlying strata through mani¬festation of mine pressure and predict the time and magnitude of incoming roof weighting. Consequently the location and timing of rib excavation can be correctly selected and thus solve several major problems in the design of mining operation.

Jan 1, 1982

By Herbert R. Babitzke

The Minerals Availability System (MAS) was formally established by the Bureau of Mines in May 1975 to provide current appraisals of the engineering and economic availability of nonfuel minerals for consideration in the formulation of both domestic and foreign minerals policy, Domes- tic mineral property reports are developed by the Bureau's four Field Operations Centers, and foreign data are obtained under contract. This site-specific information is subsequently subjected to engineering verification and economic evaluation, and the results are analyzed and published as Minerals Availability System Appraisals. The deposit-specific data are also entered into the computerized MAS data base, where a subset of this information, the Mineral Industry Location System (MILS), is available to the public in the form of computer graphics and listings. Other MAS products are also described. The Bureau's MAS personnel are frequently involved in special engineering and mineral economic projects for other Federal and State agencies. MAS personnel also work closely with the private sector, both in the area of mining and processing cost estimation, and as a source of nonproprietary mineral deposit information.

Jan 1, 1982

By J. D. Miller

The effects of operating variables on water transport to the over- flow, classification of hydrophilic particles and the recovery of copper and molybdenum from a low-grade porphyry ore are presented. Recoveries of copper and molybdenum exceeding 90 percent at a grade of 8 percent Cu and 0.2 percent Mo were realized for minus 100 mesh (1 49 µm) material at retention times of less than 500 milliseconds. The rapid rate of flotation and the effective separation of fine particles for an air sparged hydrocyclone appear to be due to directed interaction of particles in a high force field with numerous freshly formed small bubbles. This interaction occurs in the swirl flow developed by the system and is analyzed in terms of collision and induction time phenomena.

Jan 1, 1982

By N. Arbiter, C. C. Harris

The economic advantages of large diameter ball mills can be compromised by unexpected capacity limiting conditions. These arise because media rotational flow to ore axial flow ratios, and the number of mill revolutions that ore is subjected to during residence, are both inversely proportional to mill diameter. Because of this, mixing efficiency and grinding kinetics may decrease and become capacity limiting when mill diameters reach a critical range. There are two possible scale-up problems involved in the design and use of mineral processing machinery: • Selecting the size and operating conditions for available larger equipment, to insure that operating results will match those obtained with smaller units; or •Extending the size ranges of equipment beyond existing limits. Previous research at Columbia University into flotation machine hydrodynamics has demonstrated the importance in scale-up of internal flow relationships; these perform a similar role in grinding (Arbiter and Harris, 1980).

Jan 1, 1982

By John E. O’Rourke, Kevin M. O’Connor, Pamela H. Rey

INTRODUCTION The resurgence of coal mining activity in the United States, brought on by the spiraling costs of fossil fw1 energy in the Seventies, has come at a time of intense public concern for the quality of the environment. Notwithstanding pressure on our economy to develop alternate sources of fue1 energy to the import of oil, the legislatures of several states have reacted to public concern over the environment by passing strict regulations aimed at con- trolling the subsidence effect s of underground mining. Agencies of the federal government charged with assistance to the mining industry, including the Department of Energy and the Bureau of Mines, have sponsored a number of instrumentation and field measurement projects aimed at the development of subsidence prediction models that can aid the mine operator's task of subsidence control. There are good empirical models developed in Europe for subsidence prediction, but they were made possible by a large body of mining-induced subsidence data collected there over a long period of time. No com- parable subsidence data base exists in the United States, and consequently empirical modeling of subsidence is not a realistic approach for our near term needs. Moreover, the geologic and topographic diversity of the several coal regions in the United States is expected to necessitate the development of several empirical models, each one expected to be relevant to its own region. Because of the time and costs that are likely to be involved in an empirical modeling approach, it is considered more expedient and cost effective to develop a general, mechanistic model for subsidence prediction purposes. In order to develop such a model, it is necessary to investigate and quantify the mechanics of the subsidence process from the mine level up to the ground surface. The series of projects discussed in this paper are designed to achieve this objective and include the following work: (1) the identification of geotechnical instrumentation that will pro- vide mine level overburden and surface subsidence data. (2) a field demonstration of selected instruments, and (3) documentation of case histories for complete subsidence mechanics, using the demonstrated and preferred instruments. An identification of feasible instrumentation and monitoring techniques was completed by Woodward-Clyde Consultants (WCC) in 1977 (O'Rourke and others). This paper discusses a demonstration of those instruments at a mine in Utah, and at two subsequent projects, currently underway at longwall mines in Colorado and West Virginia. 'he latter two projects when complete will provide documented case histories of subsidence mechanics. The process of optimizing subsidence instrumentation and monitoring techniques to the conditions encountered during installation and monitoring for these underground mines is shown to be an evolving one, and one which has had some notable successes to date. INITIAL DEMONSTRATION The initial design and demonstration of selected monitoring systems was carried out at the SUFCO No. 1 mine, near Salina, Utah. The instrumented panel was approximately 152 m wide. 640 m long. and was 290 m to 320 m deep. The mined height of coal. seam averaged 2.4 m. The mining method was room and pillar using continuous mining machines. This method allowed some monitoring of the supported condition during development, and eventually allowed monitoring of a caved system when both chain pillars and room pillars were extracted on retreat. The two instrument systems shown on Table 1 were selected from the earlier feasibility report for demonstration at SUFCO No. 1. Collectively, the two systems, one for a fully-supported mining method and the other for a fully-caved method, incorporate most of the instrumentation to be found within all five systems listed in the earlier feasibility report. The instrumentation includes surface, subsurface and mine monitoring installations. All of the SUFCO instruments selected to meet the specifications of the general instrument types listed on Table 1 were manually operated. That is, data from the installed system could only be obtained while a person was there to physically observe or operate the system readout. Automatic data recording equipment was available for some installations, but the objectives were to keep the systems as simple as possible for the demonstration project. A complete description of the surface, sub- surface and mine level instruments, and the demonstration project results are given in WCC (1982), and selected features are discussed in this paper.

Jan 1, 1982

Preliminary petrographic investigations of eight Upper Permian coal seams of the Muja sub-basin, Collie Coalfield, reveal that the coal is high in inertinite and relatively low in vitrinite and exinite contents. The exinite content of Collie coal is relatively high when compared to other Australian coal of similar age. In addition the mineral matter content of the coal is very much lower than comparable Permian coal of Eastern Australia. The higher exinite content could be attributed to the type of Glossopteris flora, and the lower mineral matter content to the environment of deposition postulated for the Collie Coal Measures.

Jan 1, 1982