Search Documents

By David A. Summers

In May 1975 the U. S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a long-wall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting head.1 The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the pillar over onto the conveyor (Figure 1). There were several potential advantages foreseen for the system of which perhaps the most significant were the elimination of coal dust from the working area2 and the ability, with a variation in nozzle geometry, to cut webs of greater depth with a small increase in equipment horsepower. The University initially designed the head, based on experiments carried out in the laboratory, under an earlier Bureau of mines contract. The experiments showed that it was more advantageous to work at a pressure of 10,000 psi with an estimated flow rate of 50 gpm than go to the higher pressures and lower flow rates which have been advocated elsewhere.

Jan 1, 1977

By Richard Klimpel

1. Introduction Laboratory and industrial grinding tests have shown that the process of size reduction can be significantly influenced by chemicals added to the powder or slurry being ground. The terms grinding aid or grinding additive refers to a substance which when mixed into the mill contents causes an increase in the rate of size reduction. The increased rate can be used to grind a higher feed rate to the desired product size or it can be used to produce a finer product size at a fixed feed rate. Whether the use of a grinding aid is justified in any given situation depends on the cost of the substance versus the improvement of output or product quality obtained with its use. Obviously, an expensive chemical must be effective in very small concentrations if it is to be economically justifiable; the cost criteria is calculated on the basis of the cost of the grinding additive per ton of material ground. Although there is direct experimental verification of the advantageous effect of grinding additives, no sound scientific explanation has yet been offered which explains or predicts the general behavior of additives. Rose and Sullivan have summarized most of the work undertaken prior to 1950 and Hartley, Prisbrey, and Wick have recently prepared an updated synopsis of the grinding additive literature. Many of the studies reported consist of subjecting materials with simple geometric shapes to some type of hardness or controlled single fracture test. On the other hand, a number of the studies were carried out on operating industrial scale mills, with little control or precise monitoring of the effect of the additives.

Jan 1, 1977

By L. P. Johnson

Longwall mining has gained acceptance as a safe method of maintaining coal production where conventional systems were unsuccessful or uneconomic due to bad roof conditions (Kuti8). One of the major problems confronting American operators involves the correct choice of equipment which should be selected to suit the local mining and geologic conditions for optimum productivity. To achieve this, factors such as rock strengths, local geology, panel geometry, and panel orientation must be examined to optimize production and minimize down time due to ground control problems. Little quantitative information is available in the literature regarding the effects of geologic conditions on American longwall operations, and past implementations of longwall systems appear to have been based largely on experience. When mining engineers are able to assess the geologic conditions both quantitatively and qualitatively, they can more fully optimize equipment selection and panel design.

Jan 1, 1977

By Kenneth R. Krivanek

In recent years the widespread problems of air and water pollution generated by both population and industrial expansion have become a major public concern. Therefore, many municipalities are striving to achieve more efficient wastewater treatment processes so these wastewater's can be reintroduced into the waterways of our nation with little or no detrimental effects on the future beneficial use of that water. With this, improved treatment comes an ever increasing volume of wastewater sludge which must be disposed of in a manner of minimal impact on the environment. Furthermore, with demand for energy continually accelerating in this nation, our concern over high oil prices and our increasing dependency on foreign oil sources, there has been an ever growing interest in the largest energy source that are nation has, coal. However, surface mining of coal can cause many environmental problems when adequate precautions are not faithfully adhered to. These problems include water pollution from silt and/or clay erosion and acid runoff, produced by oxidation and hydrolysis of pyrite; i.e., FeS2 + 3/02 + H20 + FeSO4 + H2SO4. One method of wastewater sludge disposal which can utilize large volumes of sludge for a beneficial project that may not compound our environmental problems is spray irrigation, to either depleted farmland or to abandoned strip-mined soils. Sludge is characteristically high in organics, as well as having near neutral to alkaline pH properties. With these two qualities it possesses a potential for neutralizing acid strip mine spoils, which would enhance the establishment of a vegetative ground cover. Sludge can accomplish this by lowering the oxidation potential, reducing the solubility of iron and aluminum and by the chelation of metals, thereby

Jan 1, 1977

By R. T. Saxon

Prior to November 1975 there were several failures of front -wheel spindles on large haulage truck s in B.C., attributed to fatigue cracks. Since that time, a non-destructive test program has succeeded in detecting the cracks before catastrophic failure, However, the author regards the failures as just one example of a. general unreliability in large high-strength steel castings and urges the industry to look to forgings for sensitive components of heavy equipment.

Jan 1, 1977

By R. D. Lord

The search for the best practical means of storing sulfide bearing tailings, where there is no residual excess of carbonate material is discussed in this paper• Usually the sulfide content decomposes, with the aid of bacterial action, and the resulting sulfuric acid escapes, along with any heavy-metal solutes, through embankments that are usually porous to some degree• The problem is typified in the tailings of the uranium operations of Elliot Lake, Ont., where mining started some 20 years ago• The approach to tailings disposal paralleled the practice for other hydrometallurgical plants treating gold and base-metal ores• Impoundment areas were designed to retain solids, and a clear and neutral overflow was considered satisfactory practice• Now experience has shown that these areas, some of which have been idle for over a dozen years, release acids in seepage and overflows to an unacceptable degree• To protect natural water courses, neutralizing plants are operated wherever required• Lime slurry is fed continuously into the tailings outflows in a quantity sufficient to raise the pH to 8•5 and precipitate heavy metals that may be in solution• The objection to this procedure is that the plants will require servicing indefinitely, unless a better remedy is found• The problem differs only slightly from that common to base-metal concentrators in that here the ore has been leached with sulfuric acid for the recovery of uranium• Any native content of calcareous material has been digested, and only that added for final neutralization is available to maintain a pH unfavorable to bacterial activity• Chemical oxidation slowly lowers the pH and when this reaches a level of 4•5 or less, bacteria become active and greatly accelerate the formation of acid. The bacterial process is probably at least ten times as fast as the chemical oxidation• Location and Processing The operations referred to, uranium and one copper mine, are located at approximately 46°N and 82°W longitude• This is typical Canadian Shield country, a land of lakes, deeply glaciated and rocky, with sparse soil which supports mixed forest cover• Drainage is to Lake Huron, 25 miles to the south• Average temperature is 45°F, ranging from -40° to +95°F• Annual precipitation is 38 in•, about half of which is snow• The ore is Precambrian, quartz-pebble conglomerate, with mineralization in the matrix• From 5 to 10% pyrite is present• All known means of pre-concentration have been tested, but a bulk sulfuric acid leach has proved the most efficient. Tailings have from the outset been neutralized before release• Current practice is to add ground limestone to bring the pH to 4•5, and then lime to raise the value to 10•5• Environmental regulations have recently been increased and the foregoing meets the new standards• Separate measures are taken to precipitate radium• Remedial Measures Since the outstanding environmental problem is the oxidation of pyrite by bacterial action, the solution is to contain the products, or arrest the process• Given the ambient temperature, favorable half of the time, four items are essential to the activity• 1) Pyrite• 2) Moisture pH < 4•5. 3) Oxygen• 4) Bacteria• Removing any one of these out of the range of tolerance will bring the reactions under control• A variety of proposals considered, and a number tested for the arrest of the process, are: (a) render embankments impermeable, (b) provide an impermeable cover, (c) cover with an oxygen absorbing layer, (d) provide a vegetative cover, (e) flood the site, (f) remove pyrite from current tailings, (g) add excess limestone to current tailings, (h) poison the bacteria• Bank Seal-On existing impoundment areas, where the embankments are several thousand yards in length, it is believed that any program of injecting sealants can have small chance of success• However, a moisture barrier is an indicated specification for future construction, and this can be highly expensive• Surface Seal-Depending on the configuration of the deposit, the downward travel of water should be prevented, and oxygen excluded• Burying a plastic membrane just below the surface has been considered, as has the application of a liquid sealant that would penetrate the surface. The objection to these remedies is the excessive cost of dealing with large areas and the expectation of only temporary benefit as a result• Frost penetration is over 4 ft, and frost action breaks up asphalt paving and all but heavy concrete in a few years• Organic Layer-An oxygen-absorbing layer, such as bark fines from paper mills has been proposed as a surface treatment• Cultivated into the tailings such material might be expected to arrest subsurface oxidation for some years• Estimates are 100 tons per acre of bark fines, or 35 tons per acre of sawdust, and these enormous quantities do not so far give assurance of providing a long-term remedy• Vegatative Cover-Several obvious benefits would result from a good growth of grass or other vegetation on abandoned tailings• While restoring the natural green of the tract the growth would prevent wind-blown dust and reduce erosion• Subsurface oxidation should be reduced, as well as the upward movement of ground moisture as occurs in dry weather. To this end, considerable research and field testing has been carried out to arrive at a formula - a prescription which will provide a self-sustaining growth on the tailings surface, or at least one that would survive with reasonable maintenance attention. Many test plots have been run with different combinations of surface treatment and seed mixtures. Generally, by addition and close cultivation of limestone, lime, and fertilizers, technical success has been demonstrated• Plants with a high tolerance for acid soil seem the more hardy, and a pH above 3 is indicated so that nutrients can be absorbed• Recommendations are for 12 to 15 tons of

Jan 1, 1977

By H. W. Wevers

Fatigue failure and accompanying brittle failure occurs frequently in heavy mining equipment. This paper discusses how fracture mechanics can be applied as a tool for crack control and crack management. Information is provided to determine if particular components are prone to brittle failure. By using existing fracture mechanics formulae, an estimation of the critical crack size can then be made. It is explained that for a successful application of fracture mechanics, both the actual engineering stress in the component and the mechanical properties of the applied material must be known. The importance of toughness at low temperatures is quantitatively illustrated by calculating critical crack sizes at room temperature and at below-zero temperatures. Understanding the possibilities of fracture mechanics will also produce a climate in which the purchaser of equipment can more precisely analyze the relative quality of components with respect to crack tolerance and failure prevention. In this manner, communication between the user and manufacturer of equipment may also become more precise and effective, leading to improved design.

Jan 1, 1977

By Nick Hasenack

In the pelletizing plant of Hoogovens, Estel BV, a varying mixture of hematites and magnetites is used for the production of acid and (occasionally) fluxed pellets. Optimum results regarding productivity, quality and process control are obtained with mixtures containing 30-40 % magnetites. A decrease of the magnetite ratio or an increase of the basicity has a great influence on both productivity and heat and power consumption. Tests have been carried out to find the extent to which magnetite can be replaced by b.f. dust, mill-scale and coke breeze. Pilot plant tests show that about 80-100 % of the production loss due to a decrease in magnetite content or to the increase in basicity can be regained without damage to the quality by adding coke breeze. The amount of coke breeze should be limited tot 1,5 %; if this percen¬tage is chosen higher, the quality of the pellets deteriorates rapidly. The amount of coke breeze to be added should be about 30 % above the theoretical value, based on heat balance considerations. The results achieved by incorporating b.f. dust and mill-scale into the pelletmix were also encouraging, but as some types of mill-scale are very difficult to grind and the supply of b.f. dust is limited, the research has not been carried out extensively in this field. The pilot plant tests on replacement of magnetite by coke breeze have been followed by industrial tests, during which the breeze was added to the ore feed before the dry-grinding system.

Jan 1, 1977

By G. J. S. Govett

World mineral production is dominated by six countries - the U.S., the U.S.S.R , Canada, South Africa, Australia and China - which also hold most of the reserves of the world?s minerals. For the developed and centrally planned countries, there is a strong positive correlation between the mineral production of a country and its land area: there is no correlation between mineral production and land area for the less developed countries. These facts imply that, after taking due account of geological controlling factors, a country may expect to produce minerals in approximate proportion to its land are a provided that political, economic, and historical factors are conducive to mineral exploration and mining. Contrary to popular political belief in many parts of the world, the developed countries are the major source of mineral imports for the industrialized countries. Moreover, exports of ores and minerals account for a relatively small par t of world trade, and are an important factor in the export picture of only a few of the less-developed countries. The looming resource confrontation between the developed and the less-developed countries is based largely on the false premise that the industrialized countries of the world are minerals-poor and owe their wealth to cheap minerals from the less-developed countries. The data presented refute this. Geological controls are relatively minor in the present distribution of world mineral production; political and economic factors are dominant. It is argued that an expansion of world trade in minerals - based on increased exploration and new forms of finance for mining ventures - rather than cartels, price-fixing and trade restrictions is by far the preferable solution to the problem of redressing the legitimate grievances of the poor countries of the world.

Jan 1, 1977

By J. R. Cooper

Since man began beneficiating ores, a limited number of factors influenced the type of treatment. The ore itself has always been a factor. The first form of concentration was probably hand sorting, and the grade of concentrate and recovery had to be considered from the start. The cost of labor as a factor in mill design did not attain importance until the period following World War I. Power was one of the cheapest commodities available, and consequently power consumption was ignored. That no longer holds true. The present work does nothing to simplify the work of the metallurgist, or designer. On the contrary it adds another element to the design considerations. And while this report concentrates on power consumption, the mill designer must take the other factors into account as well. This study is based on a compilation of data supplied by a number of Western United States copper operations, as well as information from equipment manufacturers. Although its conclusiones apply to other minerals and geographic areas, the information is more precise, when applied to similar ores. The discussion has been divided into sections covering crushing, grinding, and flotation as these are the principal power consuming functions.

Jan 1, 1977

By W. G. Dallas

The social and environmental problems presented by the location of a large zinc/ lead ore body within one mile of a thriving town are described. The development problems are social, involving the education of the in habitants , and environmental, requiring the development of a planning strategy and the evolution of a baseline and post -operational monitoring system. The necessity for an environmental-impact assessment and a thorough baseline study is emphasized. The continuing psycho-social consideration of community reaction is advocated.

Jan 1, 1977

By G Luxbacher

Computer simulation of mine ventilation systems is rapidly becoming an essential tool in mine planning and design. This paper examines the utilization of ventilation simulation techniques to evaluate the number, shape, size and layout of mine entries in a typical coal mining system. Since the mains and sub-mains serve mainly for transportation and ventilation and the ventilation system is critically important to the health and safety of the workers, there exists a great need for optimal designs in this area. Evaluation criteria, could include, among others, minimization of power costs, shaft requirements and leakage. Constraints of this optimization problem include health and safety regulations and production and mine infrastructure requirements.

Jan 1, 1977

By Douglas J. Kramm

This paper discusses the history and development of the Rotary Kiln in improved fuel economy. It discusses latest technology to optimize fuel economy in a long Rotary Kiln. It discusses the limestone preheater, the SF process for cement manufacture, and the flash calciner with suspension preheat and. suspension deheat for fine limestone.

Jan 1, 1977

By W. J. Campbell

This report by the Federal Bureau of Mines Particulate Mineralogy Unit recommends mineralogical definitions and identification-characterization concepts for selected silicate minerals and their asbestiform varieties. Precise definitions acceptable to mineral analysts, regulatory personnel, and medical scientists are essential because of the present lack of conformity in terminology concerned with measuring and controlling asbestiform particulates and their related health effects. Because of the complexity and variability of crystal morphology in different mineral groups, the descriptive terms are generally explained by illustration rather than by numerical values. Applications and limitations of several analytical techniques for particulate identification and characterization are discussed.

Jan 1, 1977

By Jerome A. Westphal

The Middle Mississippi River extends from the mouth of the Ohio River to the mouth of the Missouri River, a distance of about 310 kilometers (km) measured along the river. From its founding in 1764 to the first steamboat arrival in 1817, the City of St. Louis was little more than a trading post. However, with the advent of the shallow-draft steamboat, the Middle Mississippi River rapidly became a major thoroughfare of commerce. In this regard, its importance has been reflected by the development of port facilities at St. Louis and by Federal activity relating to channel maintenance and improvement. First Federal work on the Middle Mississippi River was autho¬rized by Congress in 1824. This work was for snag removal and bank clearing and was directed at reducing the hazards to steamboat traffic, particularly during low-flow periods. During the 1820&apos;s and early 1830&apos;s, the main channel threatened to move toward the Illinois shore and abandon the St. Louis port facilities. In 1836 and 1837, Congress authorized construction of permanent improvements to keep-the river next to St. Louis (Missouri shore). By 1880, it was recognized that bank clearing activities had resulted in a wider and shallower river which exacerbated navigation

Jan 1, 1977

By John R. Bitler

A computerized napping system was developed by the Bureau of Mines to provides procedures for the rapid and inexpensive display of coal reserve data. Mapping system output consists of two types of maps, point distribution and contour (isopleth), which can be produced for data (coal analyses) associated with a point location (outcrop, drill core, or mine samples). These locations can be in the form of latitude and longitude or Universal Transverse Mercator (UTM) grid coordinates. The mapping area can range in extent from as small as a single county to as large as a multistate region. The mapping system utilizes programs developed at Harvard University, in addition to several modifications developed by the authors. The primary advantage of this system is that it enables the display of a rapidly changing data base and computerized map generation without the intermediate steps of digitizing and overlaying to produce base maps. The mapping system is applicable to any regional mineral reserve or resource study for which point location data are available. Included are example maps of the distribution of data points and contouring for sulfur content of the Upper Freeport coalbed in this western Pennsylvania demonstration area.

Jan 1, 1977

By George Delorme

"AbstractThe basic intention of this paper is to present, from a practical viewpoint, a thorough outline of all the sound and accepted principles connected with attaining satisfactory rope performance from multi-rope friction winders.In order to emphasize the importance of some aspects of rope maintenance, a limited amount of hoist rope theory has been included, a s it is felt that without this, some of the more critical, but nevertheless practical, aspects would perhaps pass without full appreciation of their individual merit.It is very much appreciated that many of the maintenance topics and practices discussed herein are already being observed with a high degree of skill among those already involved in modern friction winding. The hope is expressed, however, that the paper will be of additional assistance, and of particular help in introducing sound maintenance principles to those who are moving into this field of operation for the first time.Hoist RopesWITH a multi-rope friction winder system, structural upset within the hoist rope's cross section can occur if the ropes slip in the drum treads. This upset will usually appear at either end of the rope at the tangent point of the drum or deflection sheave with the respective conveyance in the normal uppermost position. This slipping action on the drum causes the outer cover of a Full Locked Coil or the strands of a stranded rope to shift, leading to structural upset. The result very often means that the ropes have to be withdrawn from service before completing their maximum service potential.The cause of any rope slipping in its tread can be associated with a discrepancy in tension of that rope between one side of the drum and the other."

Jan 1, 1977

By Walter D. Holland

This document is one of a series of instruction guides developed to help instructors present health and safety training courses to workers in the metal and nonmetal mining industry. This course is intended to provide above ground metal and nonmetal mining employees with training which will assist them in performing their work safely and healthfully. A document entitled, "Airborne Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas," is used as a manual for the students during the course. The unique features of the teaching guide are thumb rules for recognizing hazardous situations, candidate contamin¬ants for each work area and descriptions of control devices and work procedures.

Jan 1, 1977

By Charles R. Harrison

The purpose of this study and resulting development of the training program, "Safety--Let&apos;s Make It Happen" was to determine the relation of concepts to the development of desired Health and Safety behavior. After extensive pre-contract study, it was hypothesized that improved acceptance and understanding of the Federal Coal Mine Health and Safety Act of 1969 could possibly contribute to the reduction of accidents. Second, in order for an individual to accept and understand the Act, he or she must have a working knowledge of its purposes and application. Third, acceptance and understanding of the Act, necessary to protect the individual from negligence, was imperative. Fourth, an actual operating company could provide the base in which to test these hypotheses in a meaningful manner and develop this type of training program. Six assumptions were agreed upon before embarking on this study and training program development. (1) In the cognitive process, a concept introduction into an individual&apos;s personality may result in a behavior quite different than if he or she had been exposed to a different concept.

Jan 1, 1977

By M. T. Abasov

Among a host of challenges dictated by the explosively developing scientific and technical revolution, the improvement of control and management is one of the most essential problems. This problem is also of far-reaching importance for the oil and gas industries. An oil and gas extracting complex is an involved multilink system characterized by a great number of elements and by intricate interconnections between these elements. Of paramount importance for these systems is the quality of control. Any deviation of the control from the optimum reduces the effectiveness of the system and deteriorates its basic technical and economic factors. In case of large systems, even a relatively small deviation from the optimum may result in considerable material and power losses. Optimization of control of large production systems is therefore one of the basic means to enhance their effectiveness. The present paper discusses a development control problem for a multilayer gas deposit using the method of simultaneous exploitation of several strata by means of a single well. The optimum control is achieved by determining the dynamics of changes in the number of producing wells in a reservoir with regard to the depth of occurrence of these reservoirs as well as the difference in the time of introduction of the wells from drilling and their transfer to another reservoir. A mathematical model was constructed for the problem under consideration and a method was given to solve this problem. The problem was dealt with under the assumption that either each of the reservoirs or a part of them have vertically overlying areas and that there is no hydrodynamic interference between the horizons. It was

Jan 1, 1977