Search Documents

VOLUME I Volume I of this three-volume report is the result of development of a comprehensive, coordinated approach to site data-acquisition activities to produce key plans and reports during the evaluation and development of a surface coal mine. A logic diagram illustrates activities in the planning and decision-making process from exploration through post-mining monitoring. The report briefly discusses major elements, other than the site environment, which influence development of mining and reclamation plans and refers to other readily available literature for details outside the scope of this study. The essence of the rationale is shown to be the 1 employment of necessary skills at the proper time to evaluate specific data ' requirements and integrate them into a cost-effective program to produce initial and major feasibility reports, mining, and reclamation plans, and the environmental impact assessment.

Jan 1, 1976

By R. Blickensderfer

Several thin film absorber stacks with spectrally selective characteristics were developed by the Bureau of Mines. The stacks consisted of a silicon thick film or a zirconium compound thin film on a reflective thin film of silver. The zirconium absorber films, with the general formula ZrCxOyNz, were prepared by reactively sputtering zirconium or zirconium carbide in argon with small amounts of oxygen, nitrogen, or both, or by oxidizing zirconium films in air. A few similar types of films were prepared from titanium. The short-wave absorptance over the solar spectrum, a(s), and thermal emittance at 600 K, e(600 K), of the solar absorber stacks were calculated from room-temperature reflectance data. The values of a(s) ranged from 0.47 to 0.93, e(600 K) from 0.49 to 0.034, and the ratio a(s)/e(600 K) from 1.7 to 34. The specimen with the best combination of properties, a ZrNx-Ag stack, had a solar absorptance a(s) of 0.85 and a ratio, a(s)/e(600 K), of 24. The effect of film thickness and composition on spectral selectivity was determined. An emissometer for measuring normal total emittance up to 800 K and a method for determining a (s), e(T) (hemispherical), and a(s)/e(T) using simulated solar radiation are described. A calorimetric method for measuring a(s) and e(T) (hemispherical) at elevated temperature is also described. Measurements made on several specimens agreed favorably with calculated values.

Jan 1, 1976

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

5. General Escapeway Requirements 5.1 Escape Routes Present escapeway regulations state "Every mine shall have two separate properly maintained escapeways to the surface which are so positioned that damage to one shall not lessen the effectiveness of the other, or a method of refuge shall be provided when only one opening to the surface is possible." "Escape routes shall be a. Inspected at regular intervals and maintained in safe, travellable condition, b. Marked with conspicuous and easily read direction signs that clearly indicate the ways of escape." "Application. "Regular" intervals means at intervals no greater than monthly where conditions are stable and oftener where conditions may change." "Designated escapeways inclined more than 30* from the horizontal shall be equipped with stairways, ladders, cleated walkways, or emergency hoisting facilities." As can be noted in present and proposed regulations there must be two separate properly maintained escapeways. In most operations, the escapeways will consist of one route that is the normal travelway used in day to day operations. The second route is usually a return airway through old work areas. Based on this generally accepted practice, we will designate the two types as primary and secondary.

Jan 1, 1976

By C. H. McGuirk

Computerized Preventive Maintenance is important in maintaining consistent and efficient operation in any industry utilizing sophisticated and expensive equipment on a continuous basis. At today's large bulk materials handling facilities, the problems of continuous operation of complex machines with their thousands of components exposed to abrasion, dirt, dust and the elements, are intensified and multiplied. Effective preventive maintenance can increase profits. Yet, the number of tasks to be performed is so staggering that it is beyond error-free human capacity. The computer must be an essential ele¬ment in any efficient and economical preventive maintenance system. Computerized preventive maintenance techniques have been successfully used in many fields, usually involving highly skilled and specialized personnel working under favorable and controlled conditions. Now, The Pittsburgh & Conneaut Dock Company has developed and is applying a computerized preventive maintenance system that is applicable to the bulk materials handling industry. The "system" has taken many years of intensive effort to develop and has been time-tested and proven during the past years on equipment handling materials with rugged physical characteristics and corrosive and abrasive qualities, under some of the most adverse weather conditions on the Great Lakes.

Jan 1, 1976

At the end of August, U.S. producer posting of 99.5 percent unalloyed aluminum had been established at 48¢ per pound. At that time, dealer-quoted unalloyed ingot was reportedly at 44¢-47¢. CADMIUM: By late August, most U.S. producers had raised cadmium selling prices by 25¢ to $3 per pound. As a consequence, dealer quoting of cadmium ranged from $2.95 to $3.05 per pound. COAL: The wildcat strike, which began in southern West Virginia on July 19 and eventually spread to nine other States before ending on August 13, at its peak, idled approximately 115,000 miners and accounted for daily coal losses of an estimated 1.5 million tons at the height of the work stoppage. Concerned about the effects of the production cutbacks, the Bureau of Mines, early in the strike period, initiated its coal strike monitoring system which it had developed during the prolonged coal strike in the fall of 1974.

Jan 1, 1976

By W. W. Wen

The objective of this investigation was to study the electrokinetic behavior of oxidized coals to indicate the feasibility of separating oxidized coals from ash materials and pyrite by an mine flotation process. The effects of soluble inorganic electrolyte products from coal oxidation were also examined. The electrokinetic behavior of coals of different rank and degree of oxidation were studied by an electrophoreses technique. Generally, increasing the oxidation increases the negative value of the zeta-potential and decreases the isoelectric point (IEP). Flotation results indicate that the flotation recovery increases with decreasing pH values, and that with ferrous sulfate at pH 6.5 the flotation recovery is optimum while the pyrite was depressed. Comparing the flotation results with the electrokinetic results verified that in the presence of ferrous sulfate, the maximum hydrophobicity of oxidized coal with dodecylamine and frother is near its IEP which is around pH 6.5 to 7.0.

Jan 1, 1976

By Earl R. White

In 1950 Kaiser Steel Corporation acquired control of the Utah Fuel Company, a pioneer Utah coal concern owning large reserves of high volatile coking coal near Sunnyside, Utah. The mines at Sunnyside have been producing high quality coking coal since the late 1890's. Kaiser Steel acquired the coal deposits at Sunnyside in order to supply the necessary coke for its steel plant at Fontana, California. The Sunnyside coal deposits are made up of two mineable beds, the upper and lower Sunnyside seams. Both seams outcrop along the southward facing escarpment of the Book Cliffs. The coal seams dip under the massive sandstones of the Book Cliffs to the northeast at 5 to 22 pct., with the steepest-part being near the outcrop. Mining at Sunnyside up to 1961 had been carried on with room and pillar methods. The deep cover and rotten roof conditions, along with the need of increased tonnage, required a change of mining technique. Numerous ideas were presented, discussed, and economically analyzed. Several people involved in these discussions, with the aid of W.W. II, had been introduced to the European methods of coal mining, namely the longwall technique. The European mines had long been plagued with near similar conditions as those at Sunnyside, particularly the deep cover problem. The longwall method seemed to be working very well under these conditions, and with the extensive studies given longwalling by the Kaiser Steel mining officials, it was decided to give longwalling a try.

Jan 1, 1976

By M. K. McCarter

In 1963, a major expansion program at Kennecott's Bingham Canyon mine converted rail operation in the upper portion of the pit to truck haulage. Since that time truck-haulage capacity has increased to about 272 000 Mg (300,000 tons) per day. The majority of this production is waste material which is deposited in monolithic dumps located on the eastern slopes of the Oquirrh Mountains. The largest of these dumps, referred to as Copper Notch and Keystone, measures approximately 1830 m (6000 ft) in length, from 180 to 300 m (600 to 1000 ft) in height, and contains some 430 Tg (470 mil lion tons) of waste. The height, structure, rapid rate of growth, and anticipated leaching suggested the possibility of dump failure. In order to evaluate this possibility, an outside consulting firm was retained in 1966 to investigate the stability of the growing dumps. Their investigation indicated that, other than superficial movement, the waste dumps would be stable under static loading, and that soil distribution was not continuous enough to sustain massive foundation failure. Since this investigation, however, several failure processes have been observed. Crest settlement occurs frequently in response to compaction and over-steepening in the upper portion of the dump surface. Over-steepening results from accumulation of fines near the crest caused by natural segregation. Normally, coarse material, near the base of the dump, exhibits an angle of repose near 0.65 rad (37"). The fine material, however, stands as steep as 0.75 rad (40"). Periodic equilibrium adjustments cause stepwise settlement (Figure 1) of the dump surface and occasional sloughing of the protective berm. Routine surface preparation by dozers and graders and frequent inspections by supervisory personnel have proven adequate in preventing problems associated with this form of crest instability.

Jan 1, 1976

By L. Alan Weakly

The purpose of this paper is to present a viable method of reinforcing rock pillars by utilizing fully grouted reinforcing steel and a cement - fly ash mortar. Although the fully bonded bolt concept is not new as exemplified .by the present widespread use of resin bolts within United States mines and by the use of cement grouted reinforcing used as back pins in the Kiruna Iron Ore Mine in northern Sweden, (1)(2) the method of stabilizing mine pillars with fully bonded reinforcing is new. This method, called the "grout-rebar system", was first incorporated at St. Joe Minerals Corporation's Fletcher Mine in December of 1972. The system was used on an emergency basis before extensive research on the mechanics of the system could be completed. Since December of 1972, however, approximately 206 pillars have been reinforced at Fletcher and the system is currently being used on a regular basis at two other St. Joe mines and at two competitor mines in the area. Basically, this paper is a case study of the efforts, research and results of utilizing the grout-rebar system, on a selective basis, at the Fletcher Mine. In addition to information about the system, this paper will explain in detail the three rock mechanics instruments developed by St. Joe and used to measure and monitor rock movement to validate the grout-rebar system.

Jan 1, 1976

After World War I the character of my mining life changed completely. Before then adventure had been almost continuous but after the war there was lots of staying in one place, almost routine, between adventures. This was fortunate, as the life of a mining engineer is a wandering one at best, and it makes being married and raising a family a dubious enterprise. It would have been quite out of the question with the life I led before I got married at the end of the war The new sort of life made the "beaconing of adventure" intermittent. There were often long stays at home between wanderings which was fortunate as it changed the continuity of these memories. I must briefly summarize accounts of the more or less routine periods and concentrate on the occasional exciting episodes between. After a long visit with friends in Berkeley, Dorothy and I left for Arizona and three days at the Grand Canyon that were nearly too much for both of us. One beautiful day we started a short walk down the Bright Angel Trail. It was such a lovely bracing day that we kept on walking and enjoying the views until, just after noon, we reached the Colorado River. We were the only ones in sight so to enjoy the sunshine to the full we both had a good swim in the swiftly flowing river. So far, everything was wonderful. But when we started to climb back up the trail, rising nearly 6000 ft in ten miles we soon found that we had counted too much on our youth and endurance. We had to rest every few hundred feet and it seemed as though we would never reach the top. It was eight o'clock in the evening when we finally staggered into our room and collapsed. On the way to the Canyon I had seen John Greenway and Dr. Ricketts in Santa Barbara and they had little idea what would happen to them or to me. Before resuming his position as general manager of Calumet and Arizona and New Cornelia, Greenway must recover from the effects of the gas he had suffered in the war. Dr. Ricketts

Jan 1, 1976

By Robert G. Lundquist

This report summarizes all relevant findings and conclusions regarding capabillty of high-energy projectile impact to operate effectively in an open pit mining environment and to successfully handle secondary breakage and bench scaling problems. A silenced, aimable, mobile projectile launcher was designed and fabricated, utilizing a Government-furnished smooth-bore, 90 mm cannon. The silenced launcher was tested at the contractor's test site prior to shipment to ANAMAX Mining Company's Twin Buttes Mine near Tucson, Arizona. Demonstration tests were conducted at an inactive waste dump in the mine on 39 oversize boulders to determine the relationship between boulder size and projectile energy required for secondary breakage. The high energy projectile impact method (known by the acronym REAM -Rapid Excavation and Mining) was tested on an additional 23 boulders in the working mine and on 31 areas of potentially loose rock high on the pit walls. Most of the secondary breakage tests were successful and acceptable for open-pit mining purposes without producing large amounts of fly rock. Five of the 31 scaling tests were successful with one shot, but most of the remainder required two or more shots, and a few could not be dislodged because they were not as loose as they appeared to be, based on visual examination from a distance. Cost comparisons between the REAM method and conventional methods of secondary breakage and bench scaling are discussed. A film documentary, REAM--Mining Applications of High Energy Projectile Impact, has been produced by the contractor depicting the applications of the silenced cannon.

Jan 1, 1976

By R. R. Johnson

The Hama Mining Company owns and operates The Groveland Mine near Iron Mountain, in the Upper Peninsula of Michigan. The orebody is part of the Menominee Range of the Lake Superior District. The ore (generally known as Jasper taconite) contains an average of 35% iron ranging from 28% to 39% with an overall split of 60% magnetite and 40% hematite. The variations encountered throughout the orebody require a certain amount of blending to reduce feed changes to the mill. One of the variables which affects the crushers, as well as the mill, is the range of hardness which has a low of 7.9 and a high of 24.6 as measured by the Bond Twin pendulum impact and crushing technique. Reference is made to hardness only to point out its effect on crushing and wear rate variations. Over a period of time, these variables do, of course, average out. Mining of the low grade ore started in 1959 and has operated continuously to date. Preparation of the feed for conventional rod and ball mill grinding is accomplished by three stages of crushing. Reduction of crude ore is first passed through a 54 inch gyratory crusher; then through a secondary crusher; followed by two or three tertiary crushers in closed circuit with screens as production quotas require (Figure 1). Current demand to the crushers is about 5,200,000 tons of crude ore per year.

Jan 1, 1976

By Douglas M. Dwosh

INLAND STEEL COAL COMPANY'S experience with a gypsum cement, with and without fiber glass filler, indicates that the concept of utilizing standard rock dust equipment to dry handle and apply gypsum cement as a mine sealant is feasible, simple and economical. Prior to 1975, Inland had casually experimented with a few sealants and had discussed the advantages and shortcomings of other sealants with various users. Hower in mid-1975, Inland foresaw the need to seriously acquire a practical sealant system. There were nearly a dozen sealant materials on the market at that time: silicate-based materials, Portland cements, vermiculite cements, gypsum cements, and magnesium-oxysulfate cements, each with their own fillers and additives. The applicating equipment ranged from simple to complex: wet mix or slurry machines operating on either a batch or continuous basis, high viscosity pumps, and pneumatic, dry conveying machines with water nozzles. Compounding the selection process, two or more products could often be used with the same machine, or a given material could be successfully applied with more than one type of machine.

Jan 1, 1976

In 1955 the annual production of steel at Australian Iron and Steel Pty. Ltd., Port Kembla was 1.2 million tonne and over the following two decades this had progressively increased to the present capacity of 5.4 million tonne per annum. This increase in productivity has also been accompanied by important developments in steelmaking technology and these are explained in the chronological order in which they have taken place. Reference is made to the use of oxygen in open hearth furnaces, the B.O.S. process, the Argon-Oxygen decarburisation process for stainless steel, vacuum degassing and continuous casting. When the vacuum degassing and continuous casting units are commissioned, the Port Kembla Works will have achieved a standard of steelmaking technology equal to any in the world.

Jan 1, 1976

By Fred N. Kissell

A self-sealing brattice intended for use during coal mine rescue and recovery operations has been designed and tested by the Bureau of Mines. The major design difference between self-sealing and conventional brattice is that the fabric is cut and sewn BS a hemisphere instead of as a flat sheet. This new type of brattice offers reduced weight, leakage, and installation time. Preliminary testing indicates that the concept is worthwhile, but that further developmental research is required.

Jan 1, 1976

By Charles S. Robinson

The Henderson ore body is east of the Continental Divide in the Front Range of the Colorado Rocky Mountains about 50 miles west of Denver. The ore body is being developed for mining by workings that extend more than 3500 feet below the topographic surface. During construction of the mine workings, ground water in fractures in crystalline rocks has been encountered. From 1969 to 1973, Charles S. Robinson & Associates, Inc., in cooperation with the engineering and geologic staffs of the Climax Molybdenum Company, a division of Amax Inc., studied the ground water geology of the Henderson mine development area. Detailed geologic records of the Henderson mine were available as a result of the exploration, evaluation and development of the mine. Records of the flow, chemical composition and temperature of the ground water at and near the surface, from the entire mine, from portions of the mine, and from exploration holes drilled in the mine, were kept as the mine was developed. Where possible, ground water pressures in drill holes and changes in pressure with time, were recorded. The geologic, hydrologic and chemical data were correlated. The following conclusions were drawn from the correlations: The ground water in the Henderson mine occurs in fractures in Precambrian igneous and metasedimentary rocks and in a series of Tertiary intrusive rocks. Two zones of ground water were recognized; an active zone, in which the fracture systems are recharged and discharged annually into the surface water system, and a passive zone, in which the fractures were filled with water in the geologic past. Discharge from the passive zone is through mine workings that intersect the fracture systems. Discharge from a fracture or fracture system is initially high but decreased with tire!. The rate of decrease in flow (or pressure) is exponential. By measuring the change in flow with time, it is possible to calculate the amount of flow at some given period of time in the future. Based on changes in rate of flow and pressure, and the geology, and assuming rates of mining of the ore, it will be possible to predict the volumes of water that will have to be handled during the life of the mine and the area around the mine that will be drained by the mining operation.

Jan 1, 1976

By P. Blazy

A hydrometallurgical procedure for the recovery of metal from ore, particularly of copper from sulphide materials is described. In the course of this procedure, the raw material is first of all submitted to the action of an appropriate reducing system and then treated with a ferric salt solution which brings about the selective solubilisation of the elements to be recovered with respect to those constituting the pyritic phase. This procedure is investigated using two ore samples proceeding from massive sulphide deposits, presenting different chemical and mine- ralogical characteristics. The results of this investigation are compared with those obtained by a classical process employing a ferric salt solution. It appears that one solubilisation of copper takes place under particularly advantageous conditions when our procedure is used. The principal parameters affecting leaching of zinc, lead and copper are examined. The selectivity of this treatment is evaluated by following the change during the treatment in the pyritic phase.

Jan 1, 1976

By Carlo Grandori

Foreword In loose ground and soft rock formations, mechanical tunnel boring is necessarily dependent on the adoption of shield machines and the application of adequate support or lining structures. These structures are erected either within or immediately behind the rear portion of the shield and provide the required reaction to the forward thrust. In competent rock formations where systematic support is not a requirement, hard rock tunnel boring machines generally advance by thrusting from a structure gripped against the tunnel walls. These machines may feature a more or less extended cutterhead shield or roof support, but when in weathered, fractured or otherwise weakened ground, or in fault zones filled with soft gouge, the gripper mechanism often cannot provide enough thrust reaction to advance the cutterhead. Under these conditions, early support of the arch and walls is generally required in the form of rock bolts, steel rings and laggings and some times of a primary concrete lining placed in the short section between cutterhead and grippers. Such tunnel support measures generally fail to produce an adequate increase in thrust reaction capacity, but

Jan 1, 1976

By R. S. Jones

"Fording Coal Ltd. is now in its fifth year of a 15-year contract to supply 3 million long tons of clean coal per annum to its Japanese steel-making customers. The mine employs both conventional truck-shovel and unconventional ""walking"" dragline coal mining techniques in multiple-seam pits. This paper describes the present and future application of the 60-cu.-yd dragline and truck-shovel pre-stripping fleet in 1•ecovering 5- to 40-footthick coal seams in mountainous terrain. Deep blastholes, coal flow demands, spring ""run-off"", seam and inter-seam thrust faulting, limited seam outcrop data and regional faulting are a few of the problems encountered in this application. The author discusses these problems and their solutions as applied at Fording Coal Ltd."

Jan 1, 1976

By Dean E. Albon

In the late 1940's and early 50's in southern Illinois, the usual open pit blasting in the coal field consisted of one or two rows of churn drilled vertical holes being shot with instant electric blasting caps. The entire shot detonated at one rime. In southern Indiana and Ohio most mines were drilling horizontal holes and they too were primed with instant EB caps. During the ten years from 1355 through 1965 many changes occurred in drilling and blasting methods. The churn drill in southern Illinois and the horizontal drill in Indiana and Ohio were replaced by the rotary vertical drill. The ammonia dynamites and liquid oxygen explosives were replaced by ANFO. The elctric blasting cap in the hole was replaced by a detonating cord down line and detonating cord trunk lines made the connections between holes and rows of holes. Host open pit mining was in areas far enough from town that the noise and vibration from blasting was, if not ignored, at least tolerated. During the 1960's open pit mining expanded to account for nearly 50% of the coal produced. Mines came closer to town and towns expanded along the highways with suburban homes and mobile homes. The mines began receiving complaints about the noise and vibrations from blasting operations.

Jan 1, 1976