Search Documents

By R. K. Clifford

The formation of elemental sulfur on the surface of sphalerite in aqueous systems was investigated. Hallimond tube flotation tests showed that unoxidized sphalerite did not float well without a collector. Flotation recoveries of greater than 95 percent were obtained without the use of a collector or frother after the sphalerite had been reacted with oxygen under pressure and water at pH 2.8 at room temperature. High flotation recoveries also resulted when sphalerite was reacted in acidic solutions in the presence of platinum sponge, titanium sponge, 316 stainless steel, copper turnings, or [10-5M++]. Conditions which produced high flotation recoveries of sphalerite yielded contact angles of 37° to 40° and also produced elemental sulfur. The increase in elemental sulfur on the surface of sphalerite was detected by elemental sulfur extraction with petroleum ether, electron spectroscopy for chemical analysis (ESCA), and the electron beam microprobe. The quantity of elemental sulfur formed was insufficient to be detected by infrared or Raman spectroscopy, or by the optical microscope or by the scanning electron microscope. An electrochemical type reaction for the production of elemental sulfur in acidic solutions was proposed. The cathodic reduction of oxygen was the slow step which needed to be catalyzed. A chemical type reaction which produced H2S rather than elemental sulfur was evident in non-oxidizing conditions.

Jan 1, 1974

By Hagan T. N

Quite apart from economic considerations, the following performance parameters must be considered when selecting an explosive for a particular blasting operation. 1. total energy yield/kg, and more particularly, strain energy/kg and bubble energy/kg of charge 2. charge weight/m of blasthole 3. sensitivity of the charge 4. water resistance of the charge The effective division of an explosive's total energy into strain energy (SE) and bubble energy (BE) is explained as is the influence of each energy component on blast results. Because some rocks require a high strain energy for effective breakage, while others are most satisfactorily fragmented by bubble energy, values of SE and BE are more meaningful than those of total energy. Unfortunately, our extensive knowledge of the effects of certain variables on total energy has not yet been completely supplanted by the influence of these variables on SE and BE values. Relative SE/kg and BE/kg values are presented for a range of explosives. The 'charge density of ammonium nitrate/ fuel oil (ANFO)-type explosives is essentially constant throughout the length of the charge; because of their compressibility, slurry

Jan 1, 1974

By Kenneth R. Maser

This report describes the development of a system which modifies an existing fly ash-foam remote mine sealing technique to make it capable of impounding water in a fire zone. The modification involves blending equal quantities of fly ash and bentonite to form the bulk of the seal, and blending a thin layer of fly ash and Huron Regulated Set Portland Cement (RSPC) as a coating. The modification replaces the pure fly ash approach, but continues to use a froth foam topping to complete the seal. The modified material system is implemented with minimal complexity by adapting a "Y" connector to the existing delivery system. Each bulk hauler (fly ash and bentonite, or RSPC) will pump into one leg of the 'Y'; and the blending will be controlled by two pinch valves. The development effort has involved an evaluation of potential material systems by using small sample, quarter scale, and full head tests. The small sample tests measured the basic properties of a large number of selected material combinations. Property measurements included capillarity, permeability, shrinkage, and shear strength. As a result of these tests, particular combinations of fly ash-bentonite and fly ash-cement were selected for scale model testing in a 1 /4 scale test facility. These tests simulated, in a scaled manner, the water rise and total head which would be experienced by a seal. The tests indicated that shrinkage in the fly ash-cement combination would always result in leakage; whereas, fly ash-bentonite mixes were impervious to water.

Jan 1, 1974

By T. D. Ralston

This Bureau of Mines report presents a mathematical model for heterogeneously catalyzed chemical reactors operating under turbulent conditions. The model includes reaction kinetics on the catalyst surface as well as diffusion of the reacting components within the reactor. Three applications of the model to tube-wall methanation reactors are discussed. The first application is a computation of catalyst activity from measured reactor data. This result is then used in a reactor sizing problem and a problem of reactor simulation with recycle. In addition to the reactor model, a novel approach to solving the recycled reactor problem is given.

Jan 1, 1974

By James J. Brady

The basic story at Bear Swamp was how to excavate an underground chamber 79 feet wide by 227 feet long and 150 feet high, along with the related access, tarbrace, leads, power tunnels and shafts, do it under cost and ahead of schedule and still have just about everybody love you. The isometric sketch of the overall project follows. I won't go into any of the details of the physical scope at this point. Instead, we'll bring out the sizes, grades, particular problems of the different areas as we cover them. First of all, let's establish that Bear Swamp was a Target Estimate - Fee with Incentives type of contract. Gates and Fox's contract was with the project's general contractor, J. A. Jones. We were one of three contractors who submitted proposals and estimates to Jones. After much negotiation and many submittals, Gates and Fox was notified we had been selected to do the underground excavation on April 12, 1971. We had our first people back on site in two days, set up a temporary office, made our first steel order for jumbo erection, pacing our jumbo construction to meet the date when J. A. Jones would have the access portal ready for us. The shops, yards, dry house, compressor building were all erected as sites were designated for our use. At last, on Thursday, June 3, we trimmed the face and moved our 9-machine Euclid jumbo up a hastily constructed haul road and started our portal preparation of the access tunnel.

Jan 1, 1974

By Joseph G. Selmeczi

Lime and limestone-based SO2 scrubbing processes have demonstrated reasonably good success in removing low concentrations of SO2 from flue gases. While most of the operating problems experienced in the early days of scrubbing have been worked out, problems usually increase and removal efficiency drops with increased amounts of SO2 present in the gas stream. In order to overcome these difficulties, yet still taking advantage of lime and limestone as the lowest cost neutralizing agents, a host of so-called double- alkali systems were developed. These processes take advantage of cations such as Na+ and NH4+ capable of forming highly water soluble bases or basic salts, such as hydroxide, carbonate or sulfite, which having been neutralized or acidified by the absorbed SO2 can be regenerated with a lower cost base such as lime.

Jan 1, 1974

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars arc characteristically of the 'fire door" type that is frequently encountered on outside exit doors of many public, and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes arc added to the face equipment machinery for which they arty required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. I. Judy (our consultant), etc:

Jan 1, 1974

By Gregory E. Klosterman

American Aggregates Corporation is one of the leading producers of mineral aggregates in the nation. Production is from deposits of glacial sand and gravel and limestone and dolomite bedrock. Annual production from 33 plants is 25,000,000 tons. Land consumption is at the rate of 300 to 400 acres annually. This annual rate of consumption presents a continuing challenge to the exploration and mining personnel to meet the requirements of reserve replacement, mining and land rehabilitation.

Jan 1, 1974

By Leonard Bronitsky

The construction mineral aggregates industry--the largest industry on a tonnage basis--is threatened with large shortages in the near future. Ironically, these common minerals which include sand, gravel, and stone are among the most plentiful in the earth's crust. However, as these minerals are low in value and used in large volumes, they are extremely sensitive to transport cost, e.g., a haul of 20 miles doubled the delivered cost of mineral aggregates. Consequently, these minerals must be located close to points of demand to have economic usefulness. But the development of new deposits is virtually impossible near many urban areas for legal, sociological and economic reasons. The spector of unfinished urban transport systems, curtailed residential construction, and a general deterioration of the physical urban plant, looms as a direct consequent of future mineral aggregate shortages in the U. S. metropolitan areas. The shortages of mineral aggregates in the Greater New York Metropolitan Area (G.N.Y.M.A.) are prototypical of the shortages faced by the U. S. Metropolitan areas. This paper presents an economic analysis of the consequences of not considering the broad aspects of conservation economics as a major component of resource management. The needless annual cost for the G.N.Y.M.A. is shown to be $30 million.

Jan 1, 1974

By Hoke M. Garrett

The domestic cement industry demands about 550 trillion Btu annually, at a time when reduced fuel use has become a necessity due to the energy shortage. In terms of the overall power picture, that 550 trillion Btu, which includes both fossil and electrical energy, means about 0. 870 of all energy consumed in the U. S. The various factors influencing reduction of this energy consumption are the subject of this paper. Nationally, the energy shortage is being tackled on two fronts--increasing supply and reducing demand. Making cement consumes energy; therefore, the industry cannot join the effort to increase the energy supply except indirectly as noted later. Demand can also be attacked on two fronts--by reducing cement consumption or by reducing the amount of energy required to make cement. The following discussions on reducing cement industry energy consumption center briefly on the prospect of reducing cement consumption followed by a broad evaluation of the potentials for improving cement-making thermal efficiency.

Jan 1, 1974

By P. T. Brown

Denison Mines Limited, Canada's largest uranium producer located in Northern Ontario recently embarked upon an extensive development program that would allow them to substantially increase production and also meet the more stringent air quality standards established by the ministry of Natural Resources. To proceed with this program it was essential that the fresh air supply be greatly increased to the underground workings. A major portion of the mining area is located under Quirke Lake on the north limb of a syncline termed the Quirke Lake trough. The Denison engineers determined the most practical size and location for a proposed new fresh air shaft, eventually deciding to drive a 25 foot diameter shaft, 490 square feet in section for 1,800 feet long vertically. The shaft collar would be located on Roman Island, an island in Quirke Lake. A test hole was drilled from Roman Island to determine the ground through which the ventilation shaft would pass. This drill hole confirmed the location of the Quirke Lake over-thrust fault, a highly fractured water bearing zone 165 feet thick, approximately 800 feet below surface. Plans were made by Denison Mines Limited to seal and consolidate this ground when it was encountered by the shaft.

Jan 1, 1974

By Motohisa Kanda

The time and amplitude statistics necessary to adequately describe electromagnetic (FM) noise in mines are illustrated through computer software techniques. They are 1) Allan Variance Analyses (AVA), 2) Interpulse Spacing Distributions (ISD), 3) Pulse Duration Distributions (PDD), 4) Average Crossing Rates (ACR), and S) Amplitude Probability Distributions (APD). These statistics are illustrated using data taken from a rather large store of raw analog data recorded in operational mines. The curves generated for the illustrations characterize the noise environment in the mines from which the corresponding data were taken, and should aid in the design of reliable communication systems for such mines.

Jan 1, 1974

By Raymond E. Zimmerman

The cleaning of coal by the use of jigs is one of the oldest methods of separating coal from its impurities. Although in many situations jigs have been replaced by other methods, by far the largest percentage of coal today is still being cleaned by some form of jigs. Some piston- or plunger-type jigs are still in use throughout the world; however, the greater number are air pulsated, generally called the Baum jig, named after the original inventor, Fritz Baum of Germany. This standard jig, with slight modifications, has been in use for over 75 years. Up until recently, however, it has had certain limitations in obtaining the high performance and efficiencies required in modern coal preparation practice. TO improve its performance, some radical modifications have been made in its design and operation SO that there is now a Baum-type jig giving much higher performance in terms of capacity, efficiency and sharpness of separation- This new jig is called the Batac, and the purpose of this paper is to describe its characteristics and present data giving its performance in treating coarse and fine sizes of coal.

Jan 1, 1974

By Bruce H. Mason

The exploration for a commercially acceptable deposit of limestone is consid¬ered by many to be a relatively easy task; however, trying to locate a zone of high calcium limestone of economic thickness within a formation, which outcrops only in a narrow band varying in width from a quarter mile to ten miles, adds considerably to the normal problems experienced during an exploration program. The existence of varying glacial and karst features in the outcrop area intensified the problems encountered and complicated the interpretation of the economic value of the deposit. This paper highlights a recently completed five year exploration program during which approximately 3,900 acres of ground in seven civil townships were evaluated as potential sources of high-calcium limestone. Details are given with respect to the final site chosen and the methods used in determining the suitability of the site. This site exhibited many karat features and several methods were utilized to determine the effect of these features on the gross characteristics of the deposit. Aerial photography for both mapping and interpretation were utilized. Black and white panchromatic photography, black and white infrared and color infrared photography were flown. Resistivity, diamond core drilling and close-interval angering were used to supplement the information obtained from the aerial photography.

Jan 1, 1974

Physical model testing at Bergbauforschung is done in two rigs, a roadway rig and a longwall rig. The loading of such models, in scale relation to the con- ditions in the collieries provides valuable guidance to the probability and nature of failures, and thus to support requirements, in structural, roofbolts and self- auvancing supports. The success of such modelling when related to subsequent underground designs put to use suggests that such methods of investigation could be extended to pillar extraction problems also.

Jan 1, 1974

By Wilhelm J. Kogelmann

The quest for U.S. energy independence will result in a major increase in underground mining operations. It will necessitate the rapid excavation of development drifts, entries and slopes to exploit underground deposits of energy resources such as coal, uranium and oil shale. Most of this development work will be done in soft and medium hard rock up to an unconfined compressive strength of approximately 20, 000 psi. OBSTACLES TO RAPID TUNNEL EXCAVATION Labor In the U. S. coal mining industry, the underground productivity in tons per man-day declined from 15. 61 in 1969 to 11. 00 in 1973 which is a startling 30% decline. While productivity declines, the cost of labor and supplies continues to rise. Ralph E. Bailey of Consolidation Coal Company recently stated four reasons for the decline of productivity: A shortage of experienced miners, enactment of the Federal Coal Mine Health and Safety Act effective April 1970, major changes in union work rules in 1968, and a deterioration in the attitude of the work force (1). Because there is already a great shortage of skilled miners, the situation will get worse when large new mines for oil shale, coal and uranium open in sparsely populated areas in the Western United States. Only the large scale use of easy to operate tunneling machines can increase productivity and lower the cost of excavation.

Jan 1, 1974

Exploration requires a lot of skill, technical knowhow, and money; the money is usually less painfully available when provided by a profitable cash flow of an existing organisation that has income against which exploration cost is deductible. Planning the financing for development of a proven resource should begin at the earliest stages even while the mining plan is being formed up. The character of the participants has a bearing on the nature of the financing "package" and the structure that is to be selected for the venture. The security for borrowers in a remote mining resource is no better than the capacity of the participants to bring that resource to profitability in line with the findings of a thorough feasibility study. Taxation considerations related to the structure selected and the timing of the cash flow are of vital importance. Sales contracts have generally been a basic requirement of institutions financing mineral mining projects. Clauses relating to price, price escalation, and currency var- iations, are key factors in those contracts. Initial contracts have generally been required to cover initial overall costs.

Jan 1, 1974

By M. Shabbir

A study was made to determine the optimum conditions for precipitation of uranium from mill solutions using hydrogen peroxide. Precipitation tests were made on both synthetic and actual mill solutions. Parameters studied included amount of hydrogen peroxide, initial pH, reaction pH, time, and temperature. Also investigated was the effect of varied amounts of vanadium, molybdenum, and sulfate in the test solution on uranium precipitation and product quality. The optimum conditions for complete precipitation and high product quality were (1) the use of 150 percent of the stoichiometric requirement of hydrogen peroxide, (2) initial pH of 1.0, (3) reaction pH between 3.4 and 5.0, (4) 4 hours reaction time, and (5) ambient reaction temperature. The excess hydrogen peroxide requirement is partially dependent on the amount of impurities present in the feed solution. The hydrogen peroxide process appeared applicable to treatment of the several mill eluate and strip solutions tested. The experimental studies also indicated that the hydrogen peroxide technique gives substantially better product quality than that produced by ammonia precipitation.

Jan 1, 1974

Before commencing design of a coal prepar ation plant, it is essential to have detailed information of the raw coal to be treated to- gether with a clear understanding of the products required. Prediction of raw coal size distribution, particularly the amount of fine material, is difficult and the methods employed should be large scale pilot plant studies or techniques to simulate coal degradation and shale breakdown in water. A detailed knowledge of well proven coal preparation processes and new developments allows processes and process combinations to be compared to'obtain the maximum economic recovery when using lower cost, less efficient processes within acceptable limits. Equipment should be selected bearing in mind its precise application and the location where it is installed. Plant layout should be carefully studied to minimise equipment requirements and to simplify construction. Measurement, control and automation should be an integral part of plant design in order to obtain the optimum performance of the processing equipment.

Jan 1, 1974

By Francis Crowley

Elementary concepts of seismic wave properties are reviewed to establish a framework for discussing seismic noise and its suppression. A liberal number of references is included for those who wish to pursue the topic in detail. A base motion noise level is established for a single surface seismometer. It is argued that simple array processing and seismometer burial should regularly permit us to approach this base noise level which is found in areas free of conspicuous man-made seismic noise sources. The sensitivity of the base seismic level to a number of common disturbances is presented. Solutions that promise to hold the "effective" seismic noise at a site near the base level are given for acoustic, meteorological and fixed local surface sources. Guidelines are suggested for controlling other local man-made sources, e.g. vehicular traffic, by keeping them at sufficiently large distances away from the seismometers to keep noise at permissible levels. These guidelines are speculative and conservative. They should be the subject of future study. The ability to process against general local activity, drilling, and intra- mine sources is limited. Certainly no dramatic gain is to be expected. When strong man-made and/or intramine noise sources are not controllable, detection may well be impossible to achieve, unless the seismometer can be moved close enough to the suspected miner position, i.e. via very deep holes, to compensate for the likely vast differences in strength of the miner signal and the uncontrollable man-made noise sources. However, many intramine sources, e.g., falling water, rock bursts, explosions, etc., may well preclude the existence of a hale miner in their vicinity, and therefore any need to attempt detection of a miner at such locations. The following recommendations are made to enhance the detection and location of a miner signaling seismically. They are: 1. Seismometer burial in slim holes. 2. Narrow band detection, using multiple narrow band filters to cover the likely signal band. 3. Broadband recording and analysis for time-of-arrival estimation.

Jan 1, 1974