Search Documents

By Rejean Gagnon, Fernand Rochefort

"Haulage costs, in most operations, represent a large portion of total cost. Quebec Cartier Mining Company came to the conclusion t hat an electric trolley assist providing more horsepower than available from dieselgenerator sets presented the best oppor tunity for improvement. Accordingly, a testing and development program was carried out which resulted in the design, installat ion and application of a practical system. This paper describes the development of the system, the equipment used as well as the actual operation. A projection is also made to indicate further improvement in productivity. A comparison is made of truck operating data before and after activation of the trolley assist system in order to determine its economic impact."

Jan 1, 1972

By Phillip Philbin, Frank E. Senftle

A field neutron activation analysis technique suitable for determining uranium in ores has been tested. The method is based on the measurement of the 74.7 keV gamma ray from 'U. When the thorium/uranium ratio is greater than one or the vanadium is greater than 1%, a low uranium analysis is obtained. No satisfactory correction for thorium has been found, but a correction for vanadium can be deter¬mined. For ore containing greater than 0.01% uranium, the uranium can be deter¬mined with an accuracy of about 10% which is quite adequate for a field exploration technique.

Jan 1, 1972

To determine the relative permeability of the soil a series of percolation tests were performed at the three locations of interest at Lanse, i.e., 3C, 03A and strip bank, and KA and KB at Kato. Soil cores were removed to 2, 8, 16, 24 and 32 inch depths with the thin wall sampler tube, each core separated from the next by about fifteen feet. Then two-foot-long thin-wall tubes were inserted into the 2, 8, and 16 inch deep holes and three-foot long tubes were inserted into the 24 and 36 inch deep holes. Each tube was tamped down about one inch further to assure a bottom seal; the tubes were filled with water and the rate of fall was measured. The test is similar to those done for septic tank percolation studies 6; but is not quantitatively related to Darcy's coefficient of hydraulic conductivity because the water can flow in three dimensions from the bottom of the tube. The measurements are dependent on the length of test, since the rate of fall is a function of the head. Therefore, it should be noted that the 24 and 32 inch deep tubes should give faster percolation rates because of the one foot greater head. At locations 03A and 3C the data show a sharp decrease in percolation at increasing depth, Table XV. However, the percolation at 03A and 32 inch depth is much higher than at 3C (0.2 vs. 0.01 inches/hour); the fragipan layer must be deeper at the 3C location since this area does experience a perched water table. On the strip bank the rates of falling head are randomly variable, appearing to be as much dependent on the particular location of insertion as on depth of placement. For example, water drained from the 16 inch tube as fast as it was added, probably into a sub-surface cavity or crevice. At Kato the tubes were more difficult to place because of interference of tree roots. For this reason 2 inch deep tubes were not inserted. These short tests at Kato were inconclusive, varying extensively when the tubes were moved. Field permeability tests were also performed in two (previously described) eight-inch diameter permeater tubes at Lanse and one at Kato. Because the soil is confined inside the tube, hydraulic conductivity can be calculated according to Darcy's flow equation. The high values reported in Table XVI experienced when the tubes were rewetted from a dry surface condition, enable us to conclude that infiltration is faster than the saturated permeability of the soil. In contrast to the falling head percolation tests, these permeability results do not show a high variation between locations.

Jan 1, 1972

By R. J. Bielicki

A sorption apparatus for measuring the equilibrium sorption isotherm and the rate of diffusion of methane from fine-sized coal was designed and constructed. Preliminary work that used Pittsburgh and Pocahontas No. 3 coal shows that the diffusion coefficient varies with pressure and that the fracture spacing in these two coals is substantially different.

Jan 1, 1972

By E. G. Davis

The Bureau of Mines investigated gaseous direct reduction of low-grade iron ore concentrates in a continuous fluid-bed reactor. These studies were made in a 4-inch diameter fluid-bed reactor using hydrogen alone, and oxygen-or air-reformed natural gas as the reductants. The percent reduction is directly dependent on the mole ratio of hydrogen in the reducing gas to the oxygen associated with the iron oxide in the ore. Two-and three-stage fluid bed tests were simulated by repeated continuous tests. The results showed that percent reduction of the final product was dependent on the mole ratio of the quantity of hydrogen in the gas of each stage to oxygen in the iron oxide of the initial ore feed. Reduction as high as 87 percent in the single stages and as high as 94 percent in the multistages was obtained when either hydrogen or reformed natural gas was used as the reducing gas. Magnetic separation and concentration of the highly reduced fluid-bed product yielded a high metallic iron concentrate analyzing 85 percent total iron and 80 percent metallic iron with total iron recovery as great as 90 percent. Agglomeration of the high-grade metallized concentrate produced hard pellets analyzing 85 percent total iron and 78 percent metallic iron. Green pellets, with good strength, were made without any binder in a drum pelletizer. Direct melting of the high-metallic fluid-bed product in a basic lined arc furnace produced a nearly pure iron which contained 0.09 C and 0.01 P with 95 percent recovery of the metallic iron in the metal.

Jan 1, 1972

By J. D. Vincent

The Henderson mine site is located at Red Mountain on the eastern slope of the Rocky Mountains, approximately 50 miles west of Denver, Colorado. The mill site is on the west slope of the Rockies and mine and mill will be connected by an underground railroad. All designs were for a 30,000 ton per day molybdenite processing plant with provisions for future expansion up to 50,000 ton per day if required. This plan did not just happen, but slowly evolved over the course of about three and one-half years. Many plants cannot afford such a delay, but the Henderson project will take about 10 years from the time it was first discovered until production starts, and these 3 !1 years were well spent in determining the best possible plant site and flowsheet. This paper describes some of the problems and the decisions made in arriving at the final location and flowsheet. The paper does not go into the specific details of how protection of the environment went hand-in-hand with all other project considerations. This particular aspect of the planning has been well-reported on other occasions and considerable information on it is readily available.

Jan 1, 1972

By R. H. Smith

The total energy demand in the United States increased about 4 per cent annually during the 1960's 1 and is expected to increase at the same rate during this decade. Z Fuel oil growth in the 1960's was only Z per cent per year until 1968, but it increased to 8 per cent in 1969 and 11 per cent in 1970. Fuel oil demand is expected to grow at a 6 per cent rate through the 1970's. Part of this rapid increase in demand has been caused by restrictions placed on the sulfur content of fuels. High sulfur coal can no longer be burned in many parts of the country and has been replaced by low sulfur fuel oil. An insufficient supply of natural gas has also contributed to fuel oil demand. Air pollution regulations have not only caused an increase in fuel oil consumption, but they have also caused a reduction of sulfur content in residual fuel oils. Current regulations call for 1 per cent maximum sulfur content fuels over much of the country. Sulfur contents of fuels are limited to 0. 3 per cent in certain areas on the east and west coasts. Sulfur in residual fuel oils from high sulfur imported crude oil is reduced to 1 per cent currently. However, sulfur reduction to 0. 3 per cent is difficult and expensive.4 As a result, refiners may be hard pressed to supply the market for low sulfur fuel oil. The oil shale deposits in Colorado and Wyoming potentially are a huge source of low sulfur fuel oil. It will be shown that the low sulfur content and more importantly the sulfur

Jan 1, 1972

By T. W. White

One of the objectives of today's mine superintendent is to increase his equipment availability. To this end we have seen improved scheduling procedures, preventive maintenance programs and extensive drive training and operating procedures. However, until recently, one area that has changed little in the past twenty years is the method of refueling and servicing mine equipment. In looking at mines across the country continually one encounters the hazardous oil soaked ground, the hand held fuel nozzle and the maze of hoses of the "traditional" fuel stop. By adapting technology developed in the construction and aircraft industry, current fueling and servicing practices can be easily improved. The result will be less nonproductive time, less downtime from engine failures and increased security from major refueling fires. The time saved almost amounts to having another truck in the fleet! One feature of the improved servicing practice is the implementation of high flow fueling. For trucks now on the market, a flow rate between 120 and 150 gam is feasible, about 90 gam greater than current practice. This flow rate could be increased even further as larger trucks come into use. A second idea borrowed from the aircraft industry is the use of positive lock type connection nozzles that automatically shut off when flow stops. These may be used for fuel, water, oil and hydraulic systems to eliminate spillage and assure that clean fuel, oils, and water are delivered to the vehicles. The reduction of fuel spillage lessens the threat of major fires resulting: in equipment damage and loss. Eliminating fire hazards will become even more important as the turbine engine with its lighter, more volatile fuels come into common use.

Jan 1, 1972

By William G., Pariseau

There are important phenomena in rock and soil mechanics that cannot be explained in terms of theories of homogeneous, isotropic materials. Subsidence of strata about mine openings is an example. In-situ stress measurements in nonisotropic sedimentary, and metamorphic rocks is another. Patterns of joints, faults, fractures, and similar geologic features impart directional mechanical properties to rock masses that are locally isotropic or anisotropic. On the geologic scale, the non-homogeneity of composite rock masses may, in certain instances, be dealt with as homogeneous anisotropy. The mechanics of large rock masses can, therefore, be expected to involve considerations of anisotropy. The source of the anisotropy is not relevant. Once the scale of observation is selected and the material is defined accordingly, the analysis of stress and deformation proceeds without regard to the numerical values of the material constants. There are also important phenomena in rock and soil mechanics that cannot be explained in terms of linear elasticity, theory. For the mechanical description of anisotropic geologic materials capable of de- forming beyond the limit of purely elastic strains, a plasticity theory is required.

Jan 1, 1972

By S. F. Willey

The difficulties encountered in justifying replacements for over-age mobile mine equipment at the Gay Mine are common to most mining operations. More critical management reviews, resulting from ever rising capital expenses, increased such difficulties. These increased difficulties are especially apparent to those who are primarily operators and are not statisticians, mathematicians, or computer oriented. The Gay Mine is located 17 miles east of the town of Fort Hall in southern Idaho. This open pit operation annually supplies the J. R. Simplot Company and the FMC Corporation with 1.5 MM - 2.0 MM tons of phosphate ore. Stripping ratios average approximately three bank cubic yards of waste per ton of ore mined. The mobile mine equipment fleet consists of ten 24 yard scrapers; twenty-one 30-50 ton end dump trucks; four 32 42 yard shovels; fifteen dozers in the D-8 and D-9 classes; and three road patrols. Equipment replacement is based on the results of evaluations made on individual units. Authorization of capital expenditures for equipment replacement is dependent upon a favorable profitability index (true rate of return on investment) plus a favorable payout time. The system is based on cash flows and requires the determination of (1) the net cash outflows in the form of capital expenses plus (2) the expected cash inflows resulting from reduced expenses and depreciation tax credits. After adjustments for taxes and the time value of money, the net amounts are used to calculate the required indices. The basic elements for the system related to the replacement of mobile mine equipment include: (1) the determination of dollar penalties to be expected from the continued use of aging equipment; (2) the selection of equipment that will provide the greatest return on the investment dollars; (3) the quantification of the expected savings; and (4) the calculations of the prescribed indices. Inadequacies inherent in previous evaluating methods led to the search for more

Jan 1, 1972

By Samuel A. Goldberg

The Federal Coal Mine Health and Safety Act of 1969 delegated to the Bureau of Mines a yearly program of health inspections. Respirable coal mine dust concentrations are measured by Bureau inspectors. Samples of respirable coal mine dust are weighed to determine dust concentration and then analyzed for ash and quartz content. This paper describes the laboratory procedure for determining the percent quartz in the respirable coal mine dust samples.

Jan 1, 1972

By W. E. Lamont

Flotation studies of phosphate-bearing waste pond materials, low-grade washer products, and raw ores, all from the Tennessee brown phosphate district, showed that these types of materials could be treated without des liming to recover high-grade phosphate concentrates. The investigation showed that fine grinding before flotation was a requisite for increased recovery of the phosphate values and that the optimum pH conditions were in the range of 10.0 to 10.5 when using anionic collectors. Multiple-cleaning of the rougher phosphate concentrate was required to produce high-grade concentrates. Phosphate recoveries ranged from 60 to 82 percent and were inversely related to the grade of concentrate produced.

Jan 1, 1972

A method is proposed for the determination of antimony in ores. Antimony is volatilized as antimony iodide by heating with ammonium iodide at a controlled temperature.The fusion mixture is extracted with hydrochloric acid and the antimony content is measured by atomic absorption spectrophotometry using an air/ acetylene flame. The time taken for analysis when comparedwith existing fusion and separation procedures is considerably reduced. Cations and anions likely to be present in antimony ores were also studied for possible interference effects but were not found to interfere.

Jan 1, 1972

By R. C. Diehl

Coal, fly ash, and flue gas samples were analyzed for mercury (Hg) by double gold amalgamation-flameless atomic absorption spectrophotometry. The purpose of the study was to elucidate the fate of the trace mercury in the coal when the coal is burned. Samples were collected from a bench-scale 100-g/hr combustor, a 500-lb/hr combustor, and three coal-burning powerplants. In all cases mercury was found in the fly ash. The amounts ranged from about 9 to about 70 percent of the mercury in the coal that was burned.

Jan 1, 1972

By R. H. Snow

Although industrial size reduction methods have an energy efficiency of only about 1 percent, methods of size reduction have not changed much for many years. One reason for slow progress has been the oversimple viewpoint that a single law should exist to relate size reduction to energy input. Modern simulation methods decompose the grinding process into a grinding rate function (selection function) and a breakage function. The breakage function is difficult to measure, and it usually requires tracers if it is determined from milling experiments. Prediction of breakage functions from basic principles is one objective of this paper. In this study we focus attention not on the gross energy input to the experiment, but on the spatial distribution of stress energy within the particle. We are led to this viewpoint by experimental observations of a few previous investigators (Bergstrom2, Rumpf3, Axelson4) and our own observations. Oka and Hiramatsu recently used their calculations of stress within particles for prediction of breakage, but again they tried to correlate the size of the fragments with the total stress energy, rather than the approach we propose. We assume that the stress energy is stored in the interior of the particle as the load is increased, until the particle breaks. We assume that each element of the particle breaks into fragments of a mean size that depends on the locally-stored stress energy. The size distribution of fragments is the computed from maps of the stress-

Jan 1, 1972

By Bruce A. McFarlane

"I WOULD LIKE TO SAY how honoured I am that I have been invited to participate in this panel discussion. I have taken the liberty of narrowing my topic somewhat so that instead of speaking on the Sociology of Professions as a whole I will speak on one aspect of it, that is, on Manpower Problems in the Minerals industry of Canada, with some reference to a new social role for the professionals engaged in this industry. This probably means that I will be encroaching on areas covered or to be covered by other speakers, but I hope that when I do so I will do so from a slightly different vantage point. That is, from a sociological perspective rather than from a historical, industrial, business or professional perspective. I plan to divide my discussion into three areas, namely: (i) problems of ownership and control; (ii) environmental problems; and (iii) manpower and recruitment problems. I do not plan nor am I able to provide clear-cut solutions to the various problems I raise under these three headings. Rather, I hope that my discussion of the problems may form the basis for an extended discussion here and elsewhere. Because of the limitations of time, I will only briefly discuss the first two problem areas noted above – (i) ownership and control and (ii) environmental problems - and I plan to concentrate on the manpower issue."

Jan 1, 1972

The economic significance of a fundamental understanding of the mineral pyrrhotite is dis- cussed. Particular emphasis is placed on the relationship of other sulphide minerals to the pyrrhotite when it is the major sulphide mineral present in an ore body. Studies of the Kambalda nickel deposit are used to give a better under- standing of (a) the genesis and other character- istics of a particular ore body (b) the textural relationships between pyrrhotite and other sul- phide minerals (c) magnetic properties of natural pyrrhotite, and (e) the oxidation and supergene processes that take place in a sulphide ore body.

Jan 1, 1972

By A. M. Gaudin

At the 1971 Annual Meeting we presented a paper on the results s obtained by wet magnetic separation on very fine, slightly magnetic material . Considerable interest was shown in a corollary subject, namely; on the type of magnetic con¬struction of the Magnetic Engineering Associates (MEA) high-intensity magnetic separator (HIMS). it is the purpose of this paper to describe the principles of this separator and to give answers to many of the questions directed at us both in session and privately since the March 1971 meeting of the AIME. It is well-known that passage of a direct electric current through a wire shaped in the form of a loop results in a magnetic field being created in the volume enclosed within the loop. The magnetic field is proportional to the amperes of electric current passing through the wire. If the wire is in the form of a solenoid consisting of 11 turns, the magnetic field is n times larger. Hence the expression ampere-turns commonly associated with magnetic separators. If a particle, free to rotate and of higher magnetic susceptibility than the medium, is placed in a magnetic field, it will orient itself within that field, and it will move within the field in such a way as to go into a more intense part of the field. The traction on the particle is proportional to its inherent magnetic property which depends on its magnetic susceptibility and its volume, to the mag¬nitude of the field at the spot where the particle is situated, and to the magnitude of the field gradient at that spot. Of the three factors that control traction on a particle in a magnetic field, the magnet designer can effectively control two, the magnetic field and the field gradient. In a wet magnetic separator such as the HIMS magnetic separator, there is another force exerting traction on the particle, and that is the force of the fluid (liquid) on the particle. It is, therefore, essential to examine the relationship of the fluid to the magnetic field. First, assume the water in which magnetic and non-magnetic particles are suspended to be stagnant. In the absence of magnetic field, the only forces acting on the particles are those due to gravitation on the particles and on the fluid displaced. This is the subject, so important in gravity concentration, discussed in elementary texts of mineral engineering'.

Jan 1, 1972

By Leo R. Love

A comprehensive study of the environmental conditions of the area affected by the Colfax and Cheswick Power Stations is of extreme importance to Duquesne Light Company. The residents in the valley where the two plants are located have complained for many years about the emissions from the Colfax Plant which is of the 1920 to 1930 vintage and which has a capability of generating approxi¬mately 200 Mw. They were extremely happy to hear that the Company had plans for shutting it down, however, they were extremely unhappy to hear that we were planning to build another even larger one to take its place in the same vicinity, namely the Cheswick Plant with a capability of 570 Mw. They had visions of a plant twice the size of the Colfax Plant and belching out twice as much smoke. A few of the citizens from that area were most vehement at the public hearings that were held by the Allegheny County Air Pollution Bureau for obtaining an installation permit. With two power plants already existing in that area (Duquesne Light Company's Colfax Plant and West Penn Power's Springdale Plant), the primary concern of the Allegheny County Air Pollution Control Bureau was that the Cheswick Station might increase air pollution levels beyond what they considered to be dangerous limits. It became very evident that the Allegheny County Air Pollution Control Bureau would be extremely reluctant to grant installation and operating permits unless they were satisfied that the new plant would not increase local pollution levels and that we were taking sufficient steps to monitor the emissions from our plants and also the ambient air in the general area. We concluded that an extensive air pollution monitoring program must be conducted in the area to determine the effects of the operation of our plants. The program was conceived with our consultants, NUS Corporation of Rockville, Maryland, and was begun in June, 1968. It was designed to accomplish several things: 1. Determine the effect on the ambient air of the operation of each of

Jan 1, 1972

By D. A. Sloan

"THE FIRST COMMENTATOR that I will call on is Mr. W. G. (Bill) Brissenden, Vice-President, Mines, Noranda Mines Ltd. Bill, would you care to comment.W. G. BRISSENDEN ...Mr. Chairman, Ladies and Gentlemen, I spent some time reading the four papers that were presented here, yesterday evening, and decided that the four to six minutes that I had been allotted for this afternoon were going to be pretty tough to meet. It's a very big subject and I just hope that I will be able to stay within my time limit. As has been so aptly demonstrated by the members of our panel here this afternoon young men in growing numbers continue to be attracted to careers in the mineral industry, especially to careers in mining engineering. Now from 80 the point of view that the profession may have regained its status this is indeed welcome news. However, perhaps all of the members seem to have the suspicion that the number of mining engineers that the industry can absorb is a much lower figure than previously forecast. It is said that technical school graduates are now occupying some of the jobs once considered the private preserve of the mining engineer and also that mining engineering undergraduates are having trouble locating summer employment. If these interpretations of mine are correct then we are now confronted not only with our old dilemma - whither the mining engineer - but also with an urgent need to solve it. We cannot allow our profession to become once again an undesirable one in the eyes of our youth because if we permit such a thing to happen a second time the profession may never recover."

Jan 1, 1972