Search Documents

By G. R. St. Pierre, S. W. Gilby

The equilibrium vapors established over Fe-Cr-Ni alloys containing up to 50 pct Cr at 1600°C were determined by collecting the effusate from thoria Knud-sen cells. From these data, the activities of iron and nickel in the ternary alloys have been calculated. In a separate set of measurements, a mass spectrometer was used to determine the activities of the three components in a series of Fe-Cr-Ni alloys. In binary Ni-Cr melts, the activity coefficient of chromium referred to pure solid chromium as standard state is less than one at low chromium contents but is greater than one for melts containing more than 30 at. pct Cr. For Ni-Cr melts containing less than 10 at. pct Cr, In ?Cr = 0.15-0.92 N2. Ternary activity diagrams for Fe-Cr-Ni alloys are presented. In iron-rich alloys, the interactions between the three components are negligible; however, in nickel-rich alloys, the three principal interactions have significant positive values. THE activities of components in binary Fe-Ni alloys have been measured both in the solid solution1-3 and liquid solution4-6 temperature ranges. The determination for Fe-Ni melts have been made by three different methods: transpiration,4 Knudsen-cell effusion with analysis of an accumulated condensate,' and Knudsen-cell effusion with direct measurements of relative component intensities by mass spectrometric methods.6 The results obtained by the three different methods in three different laboratories are in excellent agreement and considerable confidence is placed in the activity coefficients for Fe-Ni melts. At 1600°C, the activity coefficients in dilute solution are ?°Ni = 0.66 and ?oFe = 0.40 for the pure liquid components as standard states. Measurements made on solid solution Fe-Cr alloys7-10 indicate that the component activities are slightly greater than ideal. The measured activities in iron-rich Fe-Cr liquid alloy11-16 indicate almost ideal behavior for this system. The recommended activity coefficient of chromium in dilute solution in liquid iron at 1600o C, ?oCr, is 1.18 when referred to pure solid chromium as standard state and 1.04 when referred to pure undercooled liquid chromium as standard state." The conversion factor of 1.14 is based on a melting point of 1857°C and an enthalpy of melting of 4047 cal per g at. for chromium.21,37 The activity coefficient of iron in dilute solution in liquid chromium has not been measured. Activity measurements on solid Ni-Cr alloys have been made by several investigators.17-20 During the review of this manuscript, Fruehan12 published the results of a study on liquid Ni-Cr alloys at 1600°C. He used galvanic cells22 with ZrO2(CaO) as the electrolyte and Cr/Cr2O3 for the reference electrode. His results indicate that ?oCr in nickel at 1600°C is about 1.01 when referred to pure solid chromium and about 0.89 when referred to pure undercooled liquid chromium as standard state. The activity coefficient of nickel in liquid chromium is unknown. The compositions of vapors freely evaporating from some molten Fe-Cr-Ni alloys have been measured by Lyubimov, Granovskaya, and Berenstein.23 Their results, combined with known vapor pressures, indicate strong positive deviation for chromium in iron-rich alloys and strong negative deviation for chromium in nickel-rich alloys. EXPERIMENTAL PROCEDURES This research was undertaken to determine the activities of components in ternary Fe-Cr-Ni melts containing up to 50 at. pct Cr. At the initiation of the research, we decided to use a Knudsen-cell method wherein a portion of the effusing vapor is condensed on a cold plate.' The composition of the equilibrium vapor for each alloy composition is determined in this method by holding the system under constant conditions for a period of time sufficient to collect enough condensate on the cold plate for chemical analysis. The activities of components in ternary alloys can be calculated from such vapor composition determinations by Eq. [1].24

Jan 1, 1970

By E. S. Shedd

Misch metal was electrowon from a treated bastnasite concentrate in a REF3-LiF-BaF2 electrolyte at 950° C. The metal was prepared and tapped from a 1,000-ampere cell, and nearly 100-percent utilization of the rare-earth oxide was achieved. Prolonged operation in a smaller cell (40 amperes) indicated that the composition of the misch metal product was reasonably constant, and no significant increase of impurities, with the exception of carbon, was noted.

Jan 1, 1970

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By Foster Fraas

Under a very high vacuum of 10-8 torr the transfer of terrestrial mineral beneficiation methods to the vacuum ambient of extraterrestrial locations such as the lunar surface was investigated. In the size range for the electro-static and magnetic separation of ores (minus 35 plus 150 mesh) there is no adhesion of particles produced by crushing and grinding due to the limited contact area, and for repeated contacts area size has a frequency of occurrence in accordance to the normal law. The photoelectric effect which is successful in separating a few minerals in an air ambient has a wider application in a vacuum, while the lack of air viscosity and sound transmission provides for high feed velocities and the adaptation of particle vibration to dispersion and grinding. Contact electrification is reversible upon return to atmosphere.

Jan 1, 1970

By D. F. Scott

"DEFINITION OF THE REGION AND ITS BOUNDARIESTHE REGION of Western Canada covered by this re-port lies between the Precambrian rocks of the Canadian Shield and the structurally deformed rocks of the eastern Cordillera, extending northward from the international border to the 60th parallel. It is some 487,000 square miles in area, with a total sedimentary fill of about 535,000 cubic miles0>. It includes parts of the prairie provinces of Manitoba, Saskatchewan and Alberta and the northeast corner of British Columbia and forms part of the geological region known as the Interior Platform, commonly referred to as the Western Canada Sedimentary Basin. The bedrock comprises carbonates and evaporites of Paleozoic age that lie on Precambrian crystalline rocks and are over-lain by a relatively thick blanket of Mesozoic and Tertiary elastic rocks. The nearly flat-lying bedrock, covered by a thick mantle of glacial drift, forms the Interior Plains physiographic province."

Jan 1, 1970

By G. J. W. Kor, F. D. Richardson

The sulfide capacities a1 1500°C of slags in the systern CaO + CaF, +Al2O3 have been measured by bringing samples into equilibrium with gas mixtures made from CO + CO2 + SO, + N2. The capacities are negligzble both JOY CaF, and CaF, + Al2O3 melts but when lime is present even at 20 wt pct capacilies as high as 30 x lom3 can be obtained. The results have yielded information concerning the liquidus at 1500°C and fluoride-oxide melts in general. The slags used in electroslag refining contain substantial amounts of calcium fluoride. Robinson and Grainger' report that good results can be obtained by using slags of the approximate composition 70 wt pct CaF2 + 30 pct Al2O3. It has also been reported2 that a mixture of 50 pct CaF2 + 30 pct A12O3 + 20 pct CaO makes a good slag for general use. In view of the fact that very low sulfur contents are claimed for ingots produced by the electroslag process. studies have been made of the sulfide capacities [c, = wt pct S (PO2/Ps2)1/2 at 1500°C. of slags consisting of pure calcium fluoride, and of its mixtures with lime and/or alumina. These studies have also provided information on the phase diagrams. The slags were brought into equilibrium with gas mixtures prepared from NZ + CO + CO2 + SO2. Because CaFz is volatile and also easily hydrolyzed. measurements were made of its loss in weight in various flowing gas mixtures. EXPERIMENTAL Procedure. The apparatus and procedure were the same as described previously. Both platinum and iridium crucibles were used (height and inner diameter about 1 cm), but those made from iridium were stronger and able to withstand a greater number of experiments. In each experiment two crucibles were set in an alumina support and 1 g of slag mixture was divided between them. The materials from each crucible were analyzed separately after being brought to equilibrium with the gas, and then quenched in the water-cooled end of the reaction tube. Materials. Alumina and lime were prepared as de-scribed previously.4 Calcium fluoride was obtained by igniting Analar calcium fluoride in a platinum boat at about 800°C in a stream of pure dry nitrogen: the product was cooled in a desiccator. The slags were produced from mixtures of the powdered constituents, these being melted together in the course of each equilibrium experiment. The sulfur analyses and the X-ray diffraction meas- urements on the solidified slags were made as described previously.4 From the latter it appears that the CaF2 contained less than 0.5 mol pct CaO. RESULTS Values of (ps2/po2) for the Gas Mixtures. The re-sults have been represented in terms of (ps, /Po,)"? for the various gas mixtures used. The va1;es of this function at 1500°C are listed in Table I: they were calculated from the data cited previously for calculations at 1350°C 4 Weight Losses with CaF, and CaF, + CaO. The re-sults of the weight loss measurements* at 1500°C for

Jan 1, 1970

By W. R. Wilcox

The camphor-anthracene system was chosen as a transparent low-melting analog of the zirconium carbide -graphite system. Camphor and zirconium car -bide both grow nonfaceted, while casting of mixtures yields platelets of both anthracene and graphite. Zone melting of thin layers of organic was observed under the microscope. Irregular lamellar structures were produced at high values of the ratio of the temperature gradient G to the zoning rate V. The anthracene invariably led the camphor, indicating lower kinetic undercooling for the anthracene. The lamellar spacing was an order of magnitude greater than typical spacings for metal eutectic systems. Exact behavior depended on orientation of the anthracene. Oriented dendritic structures were produced at low values of G/V. Transient and oscillatory behavior were also observed—much of it unexpected. A.RC-CAST refractory carbide-graphite mixtures are promising thermal-shock resistant materials. Oriented structures of these materials would be superior to arc-cast materials for many applications. Mollard and Flemings1 and Cline2 have shown that aligned structures can be obtained for a wide range of Pb-Sn alloys. However, these metals both solidify in a nonfaceted manner while graphite yields platelets or flakes. In addition only small diameter samples of Pb-Sn alloys were produced because it was necessary to avoid free convection and to have high temperature gradients. The purpose of the present work was twofold: 1) To observe the solidification of a transparent low-melting analog of carbide-graphite systems and 2) to see if larger diameter samples can be produced. EXPERIMENTAL PROCEDURE When zirconium carbide-graphite mixtures are cast, the resulting structure naturally depends on composition. Carbide-rich mixtures yield metal-like nonfaceted carbide dendrites in a eutectic matrix. Graphite-rich alloys have graphite platelets in a eutectic matrix. Empirically it was found that camphor-anthracene mixtures produce similar structures with camphor being nonfaceted and anthracene forming plates. The organic eutectic melted at 116°C and was composed of 78 wt pet camphor.3 The camphor used was U.S.P. grade from Fisher Scientific Company; the anthracene was 98+ pet fro Aldrich Chemical Co. The impurity content is judged to be on the order of 1 pet. Mixtures ranging from 50 to 88 wt pet camphor were employed for the experiments. All but one of the experiments were performed on the microscope-stage zone melting apparatus described in detail elsewhere.4 The organic mixtures were contained in horizontal cells made of microscope slides or cover glasses. In most of the cells the organic was present as a very thin layer, thus giving almost two-dimensional growth behavior. The cells were moved slowly under a heated wire, which caused a molten zone to move through the solid at rates ranging from 0.01 to 5.4 cm per hr. The temperature gradient was estimated before moving the zone by measuring the distance between the line where all solid was melted (freezing point) and that where solid first began to melt (eutectic temperature). The temperature gradient was found to be 465°C per cm in the thinnest cells used, which were made by pressing together two microscope cover slips in the organic melt and then rapidly withdrawing them. RESULTS The experimental results are described in four parts: simultaneous growth, dendritic growth, irregular growth, and transients and erratic phenomena. Steady state data are summarized in Fig. 1. Except where noted all comments are for the cells containing a thin layer of organic. A) Simultaneous Growth. Simultaneous and roughly parallel growth of anthracene and camphor was obtained over the full range of compositions investi-

Jan 1, 1970

By Giovanni Barla, Stefan H. Boshkov

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The technique of calibrating gelatin mixtures proposed by Richards and Mark in 1966 is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example with the view to describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving. The prediction of the displacement, stress field and mode of fracture associated with a given rock structure, its initial stress field, and its physical properties is essential to rock mechanics and ground control. The basic approach is to assume the rock mass to behave as a continuous, homogeneous, and isotropic medium. The classical theory of elasticity is the simplest theory based on such a concept. Specification of the elastic constants, the initial state of stress in the ground, and the boundary conditions on stress and displacement allows one to predict stress and displacement within the body. Subsequently, provided that a criterion which governs rock fracture under various stress conditions has been established, a stability analysis of the rock structure can be performed. A natural extension of the present knowledge consists of removing some of the simplifying assumptions which characterize the analytical solutions based on the classical theory of elasticity. Complex geometry, the significance of tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space are some of the important factors which are neglected in the classical approach. A better insight into the real problem can be attained with either the finite element method of stress analysis or an experimental technique. The former has already been applied with success on several occasion 1-4 and is destined to render great service in the field of rock mechanics and ground control. The latter, which will be considered in this paper, has been used extensively in applications too numerous to be enumerated. Experimental technique involves either prototype testing, if the area to be studied is accessible, or model testing. Two- and three-dimensional photo-elastic analyses are very convenient means of obtaining the stress distribution in models of complex geometry. In general, such analyses are confined to studies of stress fields around openings which are sufficiently far removed from the surface boundary so that the stresses in their neighborhood are practically equal to those produced by an initial uniform stress field; i.e., so that gravitational effects are negligible. There are, however, many rock structures where these effects must be taken into account to attain a more realistic representation of the problem. Surface and near surface rock structures, systems of openings interacting with one another, and structural components loaded only by their own weight are some of the obvious examples. This paper was written to show how factors neglected in the usual analysis based on the classical theory of elasticity, can be taken into account when gelatin mixture models are used inconjunction with photoelastic methods. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with a view to describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving. The birefringence of gelatin mixtures has been known for some time. A series of experiments were carried out by Rossi in 1910,5 but after that very

Jan 1, 1970

By Douglas A. Sloan

"Shutdowns and breakdowns that halt the process-flow of mine production are costly. Skilled maintenance tradesmen are scarce and expensive. The cost of maintenance or of production Joss from Jack of maintenance is significant and warrants considerable managerial attention.The most appropriate maintenance policy is dependent on an economic calculation. At one end of the spectrum is the policy of avoiding all breakdowns by replacement and preventive routines before failure, such as the airlines policy. At the other end of the spectrum is the policy of minimal routines and the acceptance of a breakdown as a prelude to a repair.The complexity and cost of maintenance warrants the appointment of a maintenance manager of senior status. Within the origination, there are a number of activities that can be specialized to improve effectiveness. Among these are the inspectors' activity, the establishment of improvement routines, the planning of repair tasks, maintenance engineering research and value analysis.The maintenance system is the mechanical aid to assist the staff in the implementation of the policy. It is designed to facilitate planning to make the best use of the resources. It provides information to identify areas where managerial action is required to make improvements. The job ticket is the basis of most systems."

Jan 1, 1970

By John P. Hansen

Batches of red or brown iron ore concentrates, weighing 100 or 200 grams, were reduced with gaseous reductants in a laboratory-sized fluidized-bed reactor. Using a loss of weight technique, the rates of reduction were measured and the effects of temperature, gas consumption, and gas flow rates were determined. Below about 725° C the rate of reduction was controlled by the chemical reaction at the reduction interface having an activation energy of about 10 kcal/g mole. Above about 725° C the rate of reduction appeared to be controlled by the flow of the gaseous reductant and therefore to be directly proportional to the flow rate. Above 725° C, hydrogen reduced the iron ore much faster than carbon monoxide. In gas mixtures, carbon monoxide or nitrogen reduced the hydrogen partial pressure and lowered the reaction rate proportionally. When present in large concentrations, carbon monoxide had a serious inhibiting effect on the reduction rate, probably owing to carburization and sintering of the reduced iron.

Jan 1, 1970

This Bureau of Mines report reviews the development of the world potash industry. The trends leading to the present market situation of oversupply arid low prices, which threaten; the domestic potash industry, are presented and analyzed. Because the major threat to the domestic industry comes from Canadian imports, the report focuses on the comparative economics of United States and Canadian production. The study resulted in these major conclusions: 1. Balance of world supply and demand is foreseeable in 1975, but it could be delayed by planned expansion. 2. Balance of U.S. supply and demand could occur as early as 1974-75 or as late as 1981. 3. Nearly all U. S. production capacity vis-a-vis Canadian competition is now uneconomic. Prices cover out-of -pocket costs for only 30 percent of U.S. production. 4. U.S. producers will be undersold by Canadians in 60 to 90 percent of the U.S. market. Canadians also will have the edge over United States and European producers in export markets. 5. U.S. firms have invested in 60 percent of the planned 1971 Canadian production, and they have large holdings in Saskatchewan. 6. The decline in the U.S. potash industry probably reduced personal income in Carlsbad, Eddy County, N. Mex, the chief potash-producing area in the United States, about $21.5 million between 1966 and 1969.

Jan 1, 1970

By S. Y. Mostowy, P. W. M. Shibley

"When Texas Gulf Sulphur Company discovered the Kidd Creek ore body in 1964, a crash program began almost immediately for the design and construction of a modern concentrator. It was necessary to mill two distinct ore types; one containing copper and zinc, the other lead, silver and zinc minerals. The final concentrator design was to handle 9,000 tons of ore daily in three circuits. One circuit was to treat copper-zinc and another lead-zinc ore exclusively on a permanent basis. A central circuit was designed with adequate flexibility to treat either of the above ore types in accordance with planned mining schedules. Ecstall Mining Limited, a wholly owned subsidiary, now operates the mine and concentrator complexes for Texas Gulf. The mine is located 15 miles north of Timmins and the concentrator 15 miles to the north-east along Highway 101. The ore is hauled from the mine to the concentrator over a 17-mile railroad. Initial milling operations began in November, 1966.1 - ABSTRACTThis paper deals with bulk reagent handling at the Kidd Creek concentrator. The reagent section at Kidd Creek has operated excellently since milling began in 1966. The bulk handling techniques are satisfactory. They have contributed substantially to good working conditions, economical practices and metallurgical efficiencies. The bulk handling features described should be considered in existing and proposed concentrators."

Jan 1, 1970

By W. C. Clarke

An empirical study of the nature of the embrittle-ment which occurs in martensitic and semiaustenitic precipitation hardening stainless steels upon exposure at temperatures of from about 550" to 875°F has been undertaken. This work was aimed at determining cazusation and means of controlling this phenomenon. A commercial copper bearing precipitation hardening alloy was used as a basic material for study. The effect of heat treatment variables was studied as was the effect of variations in analysis. It is concluded from the evidence that martensitic and semiaustenitic precipitation hardening stainless steels are subject to 885°F ernbrittlement similar to that observed in the straight chromium stainless steels. A characteristic of precipitation hardening stainless steels which has limited their use in certain applications is that they embrittle when held at temperatures in the range of from about 550" to 900°F. This is true to a more or less degree in all currently available alloys, either the basically martensitic type or the semiaustenitic type. The rate of embrittlement varies markedly with exposure temperature, being low at 550" to 600°F and in-creasing as the temperature increases. In spite of this embrittlement, these alloys with their unique combination of high mechanical strength, reasonable toughness, and good corrosion resistance are used in many hundreds of applications. Nevertheless, there are potential applications where the embrittle-ment described is a limiting factor. The purpose of this investigation was to study the embrittlement of these alloys and to find a way to control or eliminate it. GUIDELINES USED IN PRESENT WORK The work reported in this paper is based on a study of 17-4 PH*, a very widely used alloy. It has been used *Trademark of Armco Steel Corp., licensor. in pressurized water and boiling water atomic reactors operating at about 550°F for a number of years. As the life of such equipment is extended or operating temperatures are raised, the possibility of embrit-tlement becomes of increasing concern to materials engineers. Much investigation work was done with respect to the use of 17-4 PH at 550°F. K. C. Antony' states "Such estimation" (of an activation energy for the diffusion of chromium in iron) "would indicate W. C. CLARKE, Jr. is Senior Research Engineer, Advanced Materials Division, Armco Steel Corp., Baltimore. Md. This manuscript is based on a talk presented at the symposium on New Developments in Stainless Steel, sponsored by the IMD Corrosion Resistant Metals Committee, Detroit, Mich., October 14-15, 1968. significant secondary aging is improbable at temperatures less than 700°F within normal component service life". This statement is modified however by the recognition of the accelerating tendencies of applied stress and internal stress as well as the possible effect of irradiation. In this investigation of 17-4 PH, the H 1100 (1900°F-1 hr oil quench or air cool + 1100°F-4 hr-air cool) condition was used, partly because this condition is normally used in atomic reactors. As shown later, the precipitation hardening temperature has no real bearing on the rate of embrittlement. An exposure temperature of 800°F was selected since embrittlement at 800°F is rapid, permitting development of relative data in time periods of 400 to 500 hr. For those not familiar, a nominal present day analysis of 17-4 PH is: C Mn P S SiCrNiCuCbN 0.04 0.30 0.015 0.015 0.60 16.00 4.30 3.25 0.23 0.030 TYPICAL BEHAVIOR OF 17-4 PH Figs. 1 and 2 show the behavior of a commercial heat of 17-4 PH under the conditions defined. Characteristically, 800°F exposure causes a rapid drop in Charpy V-notch impact strength. Tensile and yield strengths gradually increase and a gradual loss of elongation and reduction of area occur, accompanied by an increase in hardness. Notched tensile strength increases to 125 hr exposure and then sharply decreases after exposure for 500 hr. The notched vs un-notched tensile ratio remains virtually constant to exposure for 125 hr (1.67 to 1.56) but drops to 1.15 after 500 hr. Tensile ductility is not alarmingly affected even after much longer exposure times than these. For example, samples aged at 1100°F for 1 hr exposed at 800°F for 4000 hr showed a drop in elonga-tion of from 13 to 11 pct and in reduction of area of from 58 to 37 pct. Notched impact is the property SmIgth KSI 3JJ[/__________^UTS-Nrteh 260 ;/- 240 —^ 200 UTS-Smooth________._, o ioo mo Sob" m Too Hours Exposure Fig. 1—Effect of exposure at 800°F for various times on notched tensile strength and smooth tensile and 0.2 pct yield strength of 17-4 PH in the H 1100 condition.

Jan 1, 1970

By Sanders GJ

Coals from the Southern Coalfield of New South Wales treated in the Port Kembla coal preparation plants of Australian Iron and Steel Pty Ltd differ substantially in their characteristics. Knowledge of, performance not only enables comparison and promotes better control, but also provides the means for predicting results. Evaluation of performance of cleaning equipment has been made in terms of probable error (Ep.) Results for Baum jigs, a Chance cone, heavy medium cyclones and water washing cyclones are examined. The efficiency factors derived from the probable error are applied to the float and sink analysis, mathematically simulating operating conditions. This method is applied to the Balgownie seam. The Balgownie seam lies between the Bulli and Wongawilli seams in the Coal measures of the South Coast and mining on a large scale began recently in the Bulli area. It is known locally as the Four Foot seam and exhibits er difficult washability characteristics, due to a comparatively high middlings content. These properties and the tively high inherent ash make careful selection of cleaning equipment essential for optimum recovery. The prediction technique is used to determine the possible results when this coal is cleaned in the Port Kembla plants. Predicted values are compared with results from full scale trial washings demonstrating the validity and accuracy of the technique. Applications of result forecasting are listed.

Jan 1, 1970

By Marcel Vallee, Fernand Dubuc

"The St-Honoré carbonatite complex, located 8 miles north of Chicoutimi, Quebec, was discovered in September 1967 as abnormal radioactivity was detected in the course of SOQUEM's aerial surveys. The complex, covered by a shallow layer of Trenton limestone, has been explored by aeromagnetic, ground gravimetric and magnetic surveys, and 12,013 feet of diamond drilling. Its age, from potassium-argon dating, is 650 million years. The carbonatite is approximately kidney-shaped and has a surface area of 6 square miles, 20 per cent of which is explored. It shows a central core of coarse-grained massive dolomitic carbonatite and an outer ring of foliated dolomitic carbonatite.The exploration work to date has resulted in the discovery, in the foliated carbonatite, of an incompletely drilled niobium (columbium) zone of pyrochlore-bearing carbonatite, at least 1,000 by 800 feet in size. This zone contains 5,000 tons per vertical foot grading 0.86 per cent Nb205 or at least 15,000 tons per vertical foot grading 0.66 per cent Nb205 or 45,000 tons grading 0.48 per cent Nb20s. The pyrochlore contains an average of 64 per cent Nb,Os. The central core contains a zone of rare-earth-bearing carbonatite (as monazite), grading up to 4.5 per cent rare-earth oxide, 3,500 ppm zinc and 290 ppm molybdenum. Stocks of nepheline syenite and magnetite diorite accompany the carbonatite. The total analysis and trace-element contents of typical rocks are presented."

Jan 1, 1970

By Norman Yarborough

Much has been written about the energy fuels including their standing with respect to reserves, their delivered Btu costs, their potential in the electrical generating market and their capabilities to meet a burgeoning demand. Yet, when all factors are placed in their proper perspective, the spiraling electrical energy market alone should guarantee each fuel a better than average market for the foreseeable future. In fact, a study made by the U.S. Federal Power Commission on the spare capacity utilities have on hand indicated that 39 of the 181 major utility systems had less than 10% reserves on hand at the end of 1969. Fuel supplies are critically low in some areas, especially in the Southeast, South Central and Midwest areas of the U.S. In other systems equipment shortages resulting from faulty equipment or delays in getting new equipment deliveries causes power failures during peak loads. In addition, lack of labor curtails the erection of some new facilities and prevents many other facilities from operating at capacity.

Jan 1, 1970

By L. C. Headley

A series of exploratory tests was conducted to determine the effects of steady electric fields on fluid flow and streaming potential in narrow passages and porous media, the effects of steady electric fields on fluid interfaces, and the influence of internal voltages on fluid flow in a porous porcelain sample. Voltages greater than about 5 kilovolts were found to influence liquid droplets emanating from a capillary tube. Solutions of polyethylene oxide and polyacrylamide in water exhibited widely different behavior than that of other liquids tested. Liquid-liquid displacement tests in porous samples to determine the influence of high voltage applied to the displacing liquid on flow rates and recovery gave no significant differences. No consistently measurable effects were noted, either on flow rate or streaming potential, when an electric field was applied transverse to the direction of flow in porous media and in narrow rectangular or cylindrical channels. Experimental values of formation factor and streaming potential for a porous porcelain sample agreed qualitatively with those calculated from electrokinetic theory for ultrafine capillaries. However, the agreement for the electroviscous effect was not good.

Jan 1, 1970

By J. J. Barakso, C. Tarnocai

This paper outlines a method of testing for the mercury content of rocks, soils and plants. Techniques of sample collecting are described and the analytical procedures outlined. Examples are given of mercury determinations in two known mineralized areas in British Columbia - Copper Mountain Mines and Pacific Nickel Mines.

Jan 1, 1970

By I. D. Shah

The Bureau of Mines investigated the sequence of principal chemical reactions taking place during the roasting of covellite (CuS). Practically all covellite is converted to digenite (Cul.SS) before oxidation to Cu20 begins. Part of the Cu2O is then converted to CuO, which in turn forms CuS04 through CuO?CuS04 as an intermediary. CuS04 and CuO'CuS04 decompose at 600° to 700° C to yield CuO and S03 (g) as final products. An overall mechanism is proposed for chemical reactions occurring at different interfaces of partially oxidized CuS pellets.

Jan 1, 1970

By M. M. Fine

Chalcocite flotation concentrates (26-34 percent Cu and 6-7 percent S) were roasted in air to determine sulfur elimination as a function of temperature, airflow rate, and residence time. Fluosolids roasting was evaluated batchwise and continuously in a 4-inch fluid-bed reactor. Kiln roasting tests were carried out in a 4-inch ID by 6-inch-long rotary drum. Pelletizing the very fine concentrates prior to roasting was essential to minimize dust losses and accretions. Concentrate pellets, sized minus 10 plus 20 mesh and bonded with 2 percent bentonite, were excellent feed for fluosol¬ids roasting and limited dust losses to 10 percent or less. One-fourth-inch pellets were best suited to kiln roasting. Both techniques were capable of producing copper calcines analyzing well under 1 percent residual sulfur when operated at 900° C with average retention times of 3 to 4 hours. Calcined pellets were strong, porous, and readily reducible.

Jan 1, 1970