Search Documents

By D. J. Bosman

Rapid fouling of condenser tubes in underground refrigeration plants is a frequent occurrence. It leads to low heat transfer efficiencies, with consequent serious reduction in capacity and increase in the horse-power requirement of the units. High pressures develop in the condensers, and frequent cleaning of the tube bundles is required. The cleaning operation takes up to 8 hours and in some cases results in significant loss of production. One of the possible causes of fouling is deposition of scale, but this can be readily overcome by controlling the concentration of the water. When water evaporates, the dissolved solids remain behind; thus evaporation increases the amount of dissolved solids per unit volume. If half the original volume evaporates, the concentration of the dissolved solids is doubled and the water is said to have a 'concentration' of two. Concentration may be controlled by regulating the amount of water allowed to bleed from the system. The actual concentration value required is a function of the chemical analysis of the circulating cooling water. In one instance, where the problem of scale formation had been eliminated, fouling still persisted, and the possibility of excessive quantities of dust in the re-circulating water was investigated. A dispersing reagent was added to the condenser cooling water as a means of preventing sludge deposition in the condenser tubes. As shown by curve A in Fig. 1 the reagent addition did not decrease the rate of fouling.

By J. C. Wilhoit, J. B. Cheatham

Although an oil well is a long cylindrical hole with an irregular bottom, it appears likely that the nature of the stress concentration at the bottom of the hole can be ascertained from an analysis of the stresses around a short cylindrical cavity with rounded comers and smooth bottom. Such a cavity is studied primarily because it leads more readily to a solution to the problem by the use of stress functions. In this paper the stress distribution around a short cylindrical cavity subjected to bit loading, overburden and drilling-fluid pressures is determined by means of an analytical solution which approximately satisfies the boundary conditions of the problem. From this solution the stresses at the corner of the hole are calculated to be about 35 per cent lower than comparable results obtained by photoelastic and relaxation analyses. This difference is apparently due to the large radius of curvature at the corner of the cavity in the present analysis. Since good agreement is obtained between the results of this analysis and the stresses calculated for a similar loading on a semi-infinite elastic solid, it is concluded that the bit action in the region near the center of the hole is not appreciably affected by the presence of the sides of the hole. INTRODUCTION Much has been written concerning drilling "under down-hole conditions" and pertaining to the stress distribution in the rock at the bottom of an oil well.1-5 For example, it is known that identical rocks can be drilled more rapidly at the surface than under subsurface conditions of pressure and stress.6 Information on the behavior of rocks under loading can be obtained from triaxial test data.7-9 From such tests it is found that rocks exhibit brittle failure when the confining pressure and pore pressure are equal, but the mode of failure may change to ductile as the difference between the confining pressure and the pore pressure is increased. Brittle failure implies that there is very little permanent deformation before fracture, whereas ductile failure indicates that permanent deformation takes place before fracture. Some rocks are ductile at differential pressures of 5,000 psi , but other rocks are brittle even at differential pressures of more than 50,000 psi. Cuttings embedded in mud at the bottom of the hole may act as a plastic mass which the bit teeth must penetrate in order to attack the virgin rock below. 10 During drilling, the mud pressure acts as the confing pressure, and in many cases the difference between the mud pressure and the formation pore pressure IS sufficiently low so that the rock most likely falls in a brittle manner. Very little penetratiori by the bit teeth may be required for brittle failure of the rock. For these brittle materials, the elastic stress distribution is of practical interest in determicing the possible effects of a given loading on failure. The penetration of bit teeth into ductile or plastic rock has been analyzed previously ll,12 and will not be considered further in the present work. During actual drilling, many teeth act at various points ovel an irregular hole bottom. In the present analysis a solution is obtained for an idealized problem of determining the elastic stress distribution caused by only one tooth acting alone at the center of a smooth hole bottom. It obviously is not proposed that any driller should put a special one-tooth bit on bottom, but it is hoped that extensions of the simpler problems can eventually lead to a better understanding of more complex actual drilling phenomena. To obtain a solution by the use of stress functions, a short cylindrical cavity with rounded corners and smooth bottom is studied. The solution to this problem should give an insight into the nature of the stress concentration at the bottom of an oil well which is in reality a long cylindrical hole with an irregularr bottom. After selection of the proper curvilinear co-ordinate system, the stress functions are expressed as series of Legendre polynomials. The coefficient of each term in the series is then determined to satisfy the boundary conditions at a finite number of discrete points on the boundary of the cavity with least square error. Results are compared with bottom-hole stresses obtained by photoelastic and relaxation analyses.

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2013 draws upon information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities performed by the mineral industry. Three sources of information are reported and analyzed in this annual review of international exploration for the year 2013: 1) budgetary statistics expressed in U.S. nominal dollars provided by SNL Metals & Mining (SNL) of Halifax, NS, Canada (formerly Metals Economics Group (MEG); 2) regional and site-specific exploration activities that took place in 2013 as compiled by the USGS; and 3) regional events that affected exploration activities, including economic, social and political conditions, that were derived from published sources and unpublished discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources are used to develop commodity and regional compilations, reported statistics may vary depending on the source and type of data that are being reported. The SNL data summarize planned company budgets for worldwide exploration activities in 2013 for 20 nonfuel mineral commodities based on surveys returned by companies primarily focused on precious metals (gold, platinum-group metals and silver), base metals (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (coal, iron ore, phosphate and potash), and specialty commodities (diamond, lithium, niobium, rare-earth elements, tantalum and uranium). Information on uranium exploration activities was included in the MEG overview for the first time in 2007. MEG included data on the commodities lithium, niobium, phosphate, potash, rare-earth elements and tantalum for the first time in 2010 because of the increased topical significance of these commodities. Since 1999, companies with exploration budgets of $100,000 and greater were included in the MEG and SNL compilations. SNL budget estimates exclude aluminum, coal, and oil and gas. Budget estimates for iron ore have been compiled since 2011 but reported separately. The post-1999 budget surveys by MEG and SNL cover at least 90 percent of world?s reported nonferrous, nonfuel mineral exploration budgets; the 2013 survey is reported by SNL to cover an estimated 95 percent of these budgets. The 5 percent that is not covered is accounted for by companies that chose not to participate in the SNL survey, private companies that do not publish their budget data, and government-funded exploration activities.

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.

By I. M. Ahmed, R. S. Hassan, M. I. Aly

Extraction and separation of La, Sm and Dy ions from acidic sulfate-phosphate solutions was investigated using a cation exchange extractant, bis(2,4,4-trimethylpentyl) phosphinic acid, CYANEX 272, in kerosene. The influence of shaking time, equilibrium pH, extractant, sulfate and phosphate ion concentrations, diluent type and temperature was studied. The extraction was found to be pH-dependent, and increasing the phosphate ion concentration inhibited the extraction which was found to be endothermic. The stoichiometry of the extracted metal species was found to be MOH.H2OHSO4H2A.A2. Aliphatic diluents were found to enhance the extraction compared to aromatic diluents. The results showed that there was a separation mode between the metal ions when varying the hydrogen ion and sulfate ion concentrations, under the used experimental conditions. The investigated process was used for the recovery of La, Sm and Dy from the acid solution resulting from the leaching of low-grade monazite.

By A. B. Cook

Gas cycling is generally considered a much less efficient oil recovery mechanism than water flooding. HOWever, recoveries from some fields have been exceptionally high as a result of gas cycling. Recovery from the Pick-ton field, for example, was calculated to be 73.5 perceni of the stock-tank oil originally in place. In evaluating pressure maintenance projects, determining how much of the recovery is due to displacement by gas and determining how much is due to vaporization of the imrnohile oil in the flow path of the cycled gas is very difficrilt. Even though most of the oil is recovered by displacetr~ent, the success of a project may depend on the amount of oil vaporized. A limited number of experiments have heen performed with a rotating model oil reservoir that simulates gas cycling operations and allows a separation of the oil from, tile free gas flowing into the laboratory wellbore at reservoir conditions, thus revealing which is displaced oil and which is vaporized oil. It Iras been determined that the amount of varporizatio'n is .significant if proper conditions exist These experiments show that oil vaporization depends on pressure, temperature, volatility of the oil and amount of gas cycled. Increases in each of these conditions increase the volume of oil vaporized. Data from six experiments affecting vaporization are presented to illustrate reservoir condition that range from favorable to unfavorable. 111 these eaperitnenis recovery by vaporization ranged from 73.6 to 15.3 percent of /he immobile oil (oil not produced by gas displacerrlt). INTRODUCTION Between 1930 and 1950, gas cycling was a popular. oil recovery practice. especially for the deeper reservoirs. Later, with many case history-type studies published for both gas cycling and waterflooding, it was generally believed that waterflooding was far superior to gas cycling, even when gas cycling was conducted as a primary production procedure by complete pressure maintenance. A good example illustrating the advantage of water-flooding over gas cycling is given in a paper by Matthews' on the South Burbank unit where gas injection was followed by waterflooding. The author concluded in part that "Early application of water injection, without the intervening period of gas injection, would have recovered as much total oil as ultimately will be recovered by waterflooding following the gas injection, and total operating life would have been shortened". This appears to be a logical conclusion. However, it should not be applied to all fields. Pressure maintenance with gas in the Pickton field, as reported by McGraw and Lohec;' will result in a much larger percentage of oil recovery than was obtained in the South Burbank unit. The great success in the Pickton field resulted partly from vaporization of the immobile oil in the flow path of the cycled gas. The amount of vaporization is related to the following conditions: volatility of the oil as reflected by the APT gravity of the stock-tank oil; reservoir temperature; reservoir pressure during gas cycling; and the amount of gas cycled. Therefore, the U. S. Bureau of Mines is investigating these effects on vaporization in a research project using a model oil reservoir. Three different stock-tank oils having 22, 35 and 45" API gravities are being used as base stock to synthesize reservoir oils. Experiments are being performcd to determine vaporization at 100, 175 and 250F and at 1,100, 2,600 and 4,100 psia. This is a progress report showing the results from six experiments. Other Bureau of Mines reports"- concerning vaporization are listed. LABORATORY EQUIPMENT AND PROCEDURES The equipment ' consists of an internally chromium-plated steel tube packed with finely sifted Wilcox sand. The tube is approximately 44 in. long and has an ID of 13/4 in. The sand section contains approximately 570 ml of voids, has a porosity of 32 percent, and a permeability to air of 4.3 darcies. A unique feature of the laboratory reservoir (Fig. 1) permits the tube part to rotate at 1 rpm while the outlet and inlet heads are held stationary. The outlet end contains diametrically opposed windows to permit observatlon of the flowing fluids, and two valves, one on the top and the other at the bottom. Oil and free gas. when being produced simultaneously, can be separated by manipulating the two valves to keep a gas-oil interface in view through the windows. Thus, only gas is produced through the top valve and only oil flows through the bottom valve. The laboratory equipment was designed to study vaporization. Therefore, a uniform reservoir was made using dry sifted sand as opposcd to using a consolidated sand core with interstitial water. Furthermore. the reservoir was tilted to minimize fingering of gas. This tilting also in-

By Feng Liu

A thermal upgrading process by which nickel value can be concentrated in a ferronickel alloy is a possible alternative to treat Sudbury pyrrhotite (Po) tailings with nickel content of 0.5–1.5 wt%. The basis of this process is precipitation of Ni from Po at high temperature once Fe/S ratio in the iron-deficient Po is shifted towards stoichiometric or near stoichiometric FeS (troilite) either by the addition of iron and/or the removal of sulfur. For the iron addition route, the reaction between elemental iron and nickeliferous pyrrhotite to produce ferronickel alloy and Ni-depleted iron sulfide phase plays a critical rule. In this paper, the formation mechanism of ferronickel alloy was investigated using the diffusion couple technique to better understand the nickel diffusion behavior in the iron and sulfide phases.

By Zhi-yong Liu

A novel process, which includes hydrochloric acid leaching, iron powder cementation, sulphide precipitation and spray pyrolysis, was proposed to treat iron concentrate recovered from zinc kiln slag for comprehensive utilization. Treated by two-stage hydrochloric acid leaching, the leaching extents of Ag, Pb, Cu, Fe and Zn are 96.78%, 95.14%, 97.72%, 94.51% and 87.74%, respectively. More than 99% Cu and Ag are recovered from the leach liquor when iron powder is 25% higher than the stoichiometric requirement. More than 96% Pb and Zn is removed with three times of theoretical consumption of FeS, and the concentration of impurities of the final solution is less than 500 mg/L. Fe2O3 powder, which is spherical with a mean size of 12 μm and purity of 99%, is prepared with final solution at 700 °C. In this process, not only the metal values can be recovered effectively, but also the iron resources of zinc kiln slag can be converted into high purity Fe2O3, thus, the comprehensive utilization of iron concentrate recovered from zinc kiln slag can be realized.

By Eckley B. Coxe

IN the anthracite coal regions of Pennsylvania the custom has been to sight either at an open light (generally a mine-lamp), or at the string of a plumb-bob. If the station was intended to he a permanent one, a spud, as it is called, that is, a nail resembling a horseshoe nail with a hole in the head, is driven into the timbers over the station, or, if there be no timber, a hole is drilled in the coal or rock roof, into which a wooden plug is driven, which serves to hold the spud. The first operation in making a survey is to lay out the stations, that is, to mark the place where the holes are to be drilled for the plugs or the points on the timbers where the spuds are to be driven in. This should be done before any instrumental work is begun, as much labor can generally be spared, and the use of very short sights can often be avoided, by carefully laying out the stations beforehand. When the stations were laid out, a plumb-bob was hung from the innermost spud, which I will call No. 1, the instrument was put in position at No. 2, by plumbing down and putting a centre-pin under the spud, and then setting up over the centre-pin, and another plumb-bob was suspended from No. 3. If great accuracy was not required, a mine-lamp was set up under the plumbbobs, at No. 1 and No. 3, and the engineer sighted at them. If great accuracy was required, a lamp or some white sbface was held by an assistant behind the strings of the plumb-bobs. To work with any speed by the latter method (i. e., the accurate one), it was necessary for the engineer to have three assistants on whom he could rely even when the chaining was done afterwards; viz. : one to hold the light behind the string at No. 1, one at No. 3, and an assistant at the instrument to hold the light while levelling, reading the in

By H. Cui

Rapid technological development has caused an increase in the demand for rare earths. Ancylite, a strontium rare earth carbonate, is a potentially significant source of rare earths. In this research paper, essential aspects of the magnetic separation and flotation processes for Bear Lodge ore are presented. A flowsheet is proposed based on an optimization of the variables and flotation simulation. The economic feasibility of the proposed processing operation is analyzed.

By Robert F. Chaken

The National Institute of Occupational Safety and Health (NIOSH) is dedicated to achieving "safety and health at work for all people -- through research and prevention." An important procedure in pursuing this goal is the NIOSH surveillance studies where the number of injuries are monitored according to demographic, employment, and injury characteristics. These numeric data are then used to identify injury risk factors, develop safety programs, and monitor implemented remediation methods. In essence, ongoing surveillance data form the bases for directing the resources of NIOSH in setting of research and prevention priorities, and in evaluating safety procedures. This surveillance techmque, which is based on the Public Health Service approach to identification and control of disease (1, 2, has been used quite successfully in dealing with relatively high number injuries such as hearing loss, musculoskeletal disorder, respiratory disorder, falls, etc. (2). However a problem arises when extending this paradigm to lower frequency traumatic events; particularly those often referred to as disasters (i.e., high impact events like mine explosions, airplane crashes, etc.). One can ask the question - there hasn't been a coal mine fire fatality in the U.S. for over ten years, to what extent should we be concerned with mine fire safety (resource-wise)? - The National Traumatic Occupational Fatalities (NTOF) system (4J which NIOSH uses to survey occupational fatalities annually, would suggest that underground mine fires would not be a high priority item in occupational safety. Yet, miners' (i.e., the exposed workers) do consider mine fires and explosions to be major safety concerns. I believe that we need to rethink our evaluation of work place disasters, what is worker exposure, and what are the underlying assumptions (both explicit and implicit) as to the impact that economic, societal and degree of hazard factors make on risk evaluation. The answers to all these problems, will require much broader considerations than those in current surveillance safety and health models. This paper discusses some facets of those considerations.

By Stéphane Bourg

The SCRREEN project gathers more than 50 European initiatives, associations, organisations or independent experts working on Critical Raw Materials (CRM) into a long-lasting network including stakeholders, public authorities, and civil society representatives. SCRREEN contributes to improve the CRM strategy in Europe by (i) mapping primary and secondary resources and substitutes of CRMs, (ii) estimating the expected demand of various CRMs in the future and identifying major trends, (iii) providing policy and technology recommendations for actions improving the production and the potential substitution of CRM, (iv) addressing specific waste electrical and electronic equipment (WEEE) and other End-of-Life (EoL) product issues related to their mapping and treatment standardization, and (vi) identifying the knowledge gathered over previous years and making the data accessible to those beyond the project. As a first step, SCRREEN worked at providing stakeholders with a comprehensive analysis of the current use of the CRM, the mapping of potential primary and secondary resources, and identification of the key technologies used in their production. Substitution profiles, analysis of European business and policy issues pertinent to CRMs, and an identification of the standards, policies, and regulatory frameworks concerning these CRM was also completed. In a second step, to be conducted between mid-2018 and mid-2019, SCRREEN will provide guidance for improving the CRM market in Europe by identifying opportunities from research, development, and innovation (R&D&I) that could reduce the supply and/or economic risks around the most relevant CRM for Europe.

The May General Meeting of the Institute was held in Kelvin House, Johannesburg on 20th May, at 4.30 p.m. Mr V. C. Robinson (Vice-President) was in the Chair in the absence, overseas, of the President, Mr J. K. E. Douglas. There were also present 16 Fellows: Messrs J. A. Adamson, R. S. J. du Toit, J. A. Drummond, D. F. A. Grave, T. L. Gibbs, G. H. Grange, D. V. Howat, P. H. Kitto, Dr P. J. LIoyd, Messrs B. H. L. Leach, J. de V. Lambrechts, Dr J. T. McIntyre, Messrs C. S. MacPhail, P. W. van Rensburg, S. G. Taussig, W. S. Rapson. Six Members: Messrs E. L. Atkinson, R. Hemp, Dr J. Martinson, Messrs A. H. Munro, G. J. van Jaarsveld and J. H. Qwilliam. Two Associate Members: Messrs B. H. van Rensburg and H. Triiter. Four Visitors: Prof J. E. Kerrich, Dr G. K. Sluis-Cremer, Messrs D. Kisbey-Green and L. W. Isserow. For Secretariat: Mrs S. de Gersigny. Total present: 27. OBITUARY The Vice-President: "It is my sad duty to announce the death of Stephen Ring, a member who joined the Institute in ]961, and passed away on the 31st of December, 1969. I would ask you all to rise and observe a moment's silence. Thank you." MINUTES The Vice-President: "May we confirm the minutes of the Special General Meeting and Monthly General Meeting, held on 20th February, 1970, as published in the April issue of the Journal?" MEMBERSHIP The Vice-President: "I have much pleasure in announcing that the names of the undermentioned candidates, having been published in accordance with By-Law 5 2.2, Council has elected them to membership of the Institute in the following grades: Fellows: Denis Ian Field, Arthur Cecil Waiter Comyn, John Hall, Leon VercueiI. Members: Jan McLellan Vosloo, Jan van Velze. Graduates: Richard Darnley Beck, John Edward Andrews, Roderick Nowell Randell. Associates: Alexander Duncan Ross, Ian James Terrill. Students: Hendrik Jacobus Oostenwald Prins Smith, Graham Peter Gooding, Rudannes Raath Homan. "I welcome the newly, elected members to the Institute." GENERAL BUSINESS The Vice-President: "Are there any matters which you wish to raise under 'General'? There being no matters to raise under 'General', we will proceed to the next item on the Agenda." PAPER FOR PRESENTATION The Vice-President: "It is my pleasant duty to call on Dr du Toit to deliver his paper, entitled, 'The functional relationship between dust hazard and the rate of collecting funds to pay compensation for pneumoconiosis'." After the presentation of the paper (published in the March Journal) the Vice-President said: "This paper is a very important addition to the considerable volume of work applications on this subject of pneumoconiosis. The disease, in all its various forms, has received attention from many, many great men, both in the medical world, and engineers. The fact that there is this big volume of publications of literature on it still doesn't mean that we can get anywhere beyond the old, simple injunction, that the prevention of pneumoconiosis does not depend on compensation, levies or anything else. It simply depends on allaying dust as quickly as possible. "This paper, however, is another scientific landmark and I think, in a cold and dispassionate way, it sets out some important points in this whole subject of the relationship of the levy - the money of compensation to the dust which causes it. "I have, personally, very little to criticise in this paper but when I listened to Dr du Toit's final conclusions, I wondered whether the words, 'Within the data available', aren't the key to this whole situation. I agree that he has demonstrated a workable relationship between the current industries for levy and dustiness, but among the factors which he lists as being important, I know that there is one which is missing. This is extremely difficult to evaluate. It's a factor which has destroyed, on so many occasions, the work which has been done by so many genuine, intent, honest people working in this field, and this is this unknown factor, this hidden factor of political opportunism, which has so often played a very important part in pneumoconiosis compensation. "How many of us have seen the grubby, grasping fingers of power-mad demagogues, and I can name them for you - but I won't - and also the blatant vote-catching of certain politicians interfering in this field. How, at the end of all that, the poor scientist, the poor dedicated man in the Mines' Department, who has to write the law of compensation, can operate, I do not know. "From this picture the ordinary layman recoils in horror. Among the casualties in this particular war, which has been fought over so many years, I am perfectly certain, are some of the criteria of certification, especially in '56/,57, when that extraordinary condition, known as 'pulmonary disability' was introduced. I am sure there were casualties then, in the criteria of certification. "Nevertheless, this paper is a worthy addition to the long list of scientific work done on this so-important

By Dalene Joalet Steenkamp

Excavation of industrial-scale furnaces allows for the systematic study of reaction sequences by identifying the different reaction zones within the furnace. In 2013, Transalloys excavated a 48 MVA submerged arc furnace that was used for silicomanganese production using the ore-based route. The excavation method was reported elsewhere as was observations made in terms of refractory wear and modes of electrical energy dissipation prior to excavation. The paper presented here, reports on the process reaction zones observed during the excavation and subsequent phase chemical analyses of a number of process samples obtained during the excavation. The zones identified were a loose burden zone, a dry coke-bed zone, a wet coke-bed zone, a hard build-up zone, and an alloy zone. The results are compared to observations made in the excavation of an industrial-scale SAF and a pilot-scale SAF in Norway. The presence of the hard build-up zone below one of the electrodes and absence of a slag zone below all three electrodes are unique features of the SAF excavated at Transalloys.

By G. A. Christie

This paper presents a vision system capable of providing an accurate estimate for the volume of stockpiles using 2D images. By imaging a stockpile from multiple viewpoints with a two-camera system, a 3D point cloud of known scale is generated using image-based 3D reconstructions. With a small amount of user interaction, the points that correspond to the surface of the stockpile are extracted and used to measure the volume. The hardware required for the two-camera system is light enough to be carried by a small unmanned aircraft and is a cheaper alternative to LiDAR while still being competitive in terms of accuracy. When testing the volume measurement algorithm on a stockpile of known volume, the measured output was found to have less than a 3% error from the ground truth.

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

By E. R. Darby

When bronze is melted in open-flame furnaces a considerable amount of slag is formed during the melting operation. This slag may be incidental to the melting practice or it may be formed intentionally by slag-forming constituents added to the furnace charge to provide a covering for the melted metal When this slag is removed from the furnace, it contains, in addition to the free metal carried with it by the skimming operation, a considerable amount of metal as oxide either combined or mechanically mixed with it. By the usual crushing and washing methods this metallic oxide generally goes to the tailings pile, so diluted by other foundry waste that its recovery is economically impossible. If this furnace slag is not inixed with other foundry waste, practically all of the metal oxide as well as the free metal may be recovered by some form of smelting operation. The first side of the problem to be considered is the amount of slag produced. It may not be true that the majority of foundries have no record of the amount of slag made, but it is certainly true that a very great many either have no record or pay little attention to it. Usually the collection of furnace slag for one normal week's run will be sufficient to determine the advisability of its being handled in a different manner from the crushing and concentrating generally employed. If a large representative sample of the accumulation is crushed and concentrated and the recovery compared with the results of a careful assay, it will be found that a large percentage of the total metal content was lost in the washing process. The percentage of loss will be greater than the metallic oxide content, as some free metal in extremely fine particles always is carried away in grains of slag. From such a comparison, it may be determined whether or not the slag should be melted, sold or treated as before. An example of an actual test of this kind is given below. In a foundry melting 50,000 to 80,000 Ib. of bronze per day, a week's accumulation of furnace slag and ladle skimmings amounted to 16,500 1b.—over three times as much as the foundry superintendent estimated before the accumulation was made. Two tons of this material was taken as representative of the lot. This was ground through a thoroughly cleaned ball-mill and concentrated over a Wilfley table. The

By J. Downie, H. A. Kendall, G. H. F. Gardner

Some cases of the motion of two miscible fluids in uniform linear models are discussed. There is no bulk flow through the models, and the convection currents are caused solely by density gradients. Horizontal, vertical and inclined positions of the models are treated separately. Analytical formulas for the motion of a narrow transition zone between the fluids are obtained and compared with measurements, and the limitations are discussed. Observations of the ultimate stabilizing effect of diffusion on the motion me compared with the theory. It is shown that fluid motion in an inclined model with a constant rate of bulk flow can be directly deduced from the cases discussed, provided the viscosity ratio is small. INTRODUCTION In some reservoirs, convection currents caused by variations in the fluid densities may be significant. For practical purposes it may be desirable either to minimize the effect, particularly in miscible displacement, or to maximize the effect as in some schemes for the production of heavy crude oils by combustion. Experiments by Craig, et al,l have shown the effectiveness of gravity in reducing the efficiency of a miscible displacement when the mixed zone between the displacing and displaced fluids is narrow compared with the height of the system. The presence of a board transition zone from one fluid to the other has been shown by Perkins, et al,2 to nullify considerably the influence of a difference in density. Indeed, the theoretical discussion given by Perrine3 has shown that when the transition zone exceeds a certain critical length the efficiency approaches 100 per cent. Many additional results 495 have been published on miscible and immiscible displacements which show the importance of density difference and also mobility ratio. The aim of the present paper is to discuss some cases of gravity segregation of miscible fluids in linear models such as are often used in the laboratory to evaluate recovery processes, and to supply additional experimental evidence in support of the conclusions. An attempt is made to calculate simply the magnitude of the fluid motion caused by density pdients and mobility ratios, and to quantify the modifications in the fluid motion produced by the combined effect of molecular and convective dispersion. However, it should be pointed out that the uniform permeability of the models and the use of only a single pair of fluids (whereas several pairs of fluids may be employed in a recovery scheme) severely restricts direct conclusions about natural reservoirs. For conciseness, the motion generated by density gradients is emphasized for the case of no bulk flow through the models. This is not a drastic limitation because, as shown in Appendix A, a fluid motion with a constant bulk flow through any linear model is equivalent to a fluid motion with no bulk flow in the same model inclined at a different angle to the horizontal, provided only that the density is a linear function of the viscosity of the fluid mixture. HORIZONTAL MODEL In this case the model is assumed to have a rectangular cross-section with a horizontal breadth b, vertical height and a great length L. Throughout.the paper it will be assumed that x-axis points along the length, the y-axis along the width and the z-axis along the height. Thus, in the present case the x, y plane is horizontal. Initially, the transition zone between the fluids is assumed to be thin and parallel to the y, z plane. An example of this situation in a practical problem arises in a scheme for using air for cushion gas in the storage of fuel gas in aquifers. 6 With the passage of time the denser fluid sinks and spreads along the bottom of the model while the lighter fluid rises. The interface extends from the top plane of the model to the bottom. Experiments have shown that for practical purposes this interface may be treated as a plane surface at all times. The surface is significantly curved, however, for viscosity ratios greater than about 10. Other complications arise with large viscosity ratios because of the nonlinear dependence of the viscosity on the composition of the mixture, so that the simple results given here are restricted to fairly low viscosity ratios.

By S. C. Miller, R. D. Carter, H. G. Riley

A merhod based on theoretical considerations is presented for estimating srabilized performance of gas wells from data obtained from short-term flow tests. Calculated results are presented for II gas wells evaluated with four-to five-hour flow tests. For seven wells on which comparison war available, satisfactory agreement between measured and calculated performance was obfained. Although the final results are favorable, diflerences in flow capacity k,h obtained from flow tests conducted at different rates were observed. This inconsistency did not seriously affect the calculated results in the test wells. INTRODUCTION In order to negotiate the sale of gas from newly drilled gas wells and to plan otherwise for the orderly exploitation of gas reserves, it is necessary to predict the long-term withdrawal rates physically possible for each well. Since low permeability gas wells do not stabilize except after a lengthy period of flow, the operator is unable, without wasting large amounts of gas, to measure directly the stabilized performance prior to contracting for sale of the gas and connecting the well to a pipeline. This problem is not new, but is one which has recently received considerable attention because of the rising importance of natural gas in the economy and new emphasis on the development of gas reserves. Thus, a method is needed for estimating stabilized performance from information obtained from short-flow tests in which stabilized flow is not attained. Such short tests would be suitable for wells not connected to a pipeline since the tests require only small amounts of time, labor and production of gas. Other requirements of such a method are short calculation time and use of a model of the gas well and its reservoir drainage area which is as consistent as possible with present theoretical, experimental and field knowledge. The method presented herein was developed in an effort to meet these requirements. It has been named the "two-Row method". In addition to the section on the evelopment and description of the method, a description of field application of the method and a discussion of well test results are in- cluded. Finally, there is a section on an additional consideration prompted by some of the test results. The Appendix contains certain details of the derivation of the two-flow method and a sample calculation for Test Well 1. MATHEMATICAL DEVELOPMENT AND DESCRIPTION OF THE METHOD The method is based upon the following assumptions: (1) The system can be described as a finite cylindrical gas reservoir produced by a single cylindrical well located at the center of the reservoir. Flow is strictly radial. (2) Flow obeys Darcy's law except very near the well where a quadratic flow law is assumed. (3) The system is also characterized by a laminar flow skin factor. The use of a quadratic or turbulent flow term is more fully justified in Refs. 1 and 2. When such a system is opened at the wellbore to constant rate flow from an initial condition of uniform pressure distribution, the radius or drainage quickly passes through the non-Darcy flow and "skin effect" region imrnediately surrounding the well. After the drainage radius or "transient" has passed beyond this region and before it reaches the external boundary, drawdown can be expressed by'." After the drainage radius reaches the external boundary, stabilized flow exists and drawdown is given by'," Eqs. 1 and 2 form the basis for the method. The validity of these equations will now be examined in the light of some well test data previously available. It has been found by actual measurements on gas wells that the relationship between drawdown and flow rate, that is the performance curve, is closely approximated by' Eq. 3 is a straight line on log-log graph paper. Eq. 2 and, for any lixed value of time, Eq. 1 plot as a curve which is slightly concave upward on log-log graph

By N. T. Lowe, R. E. Miller

When two pieces of heavy equipment interact, jolting and jarring can occur. During haulage truck loading for example, there is a chance that the operator of one or both pieces of the equipment will experience jolting and jarring. Additionally, a jolt can occur when an off highway equipment operator drives over a road defect or inadvertently strikes a berm. Aside from the operators, there is seldom anyone else that witnesses the interaction and can accurately describe the extent of the jolting. This makes it difficult for health and safety managers to address jolting and jarring. The devices and software described in this paper constitute a method for installing “black boxes” called Shox Boxes onboard equipment that already have a GPS system onboard. The resulting configuration provides an objective assessment of jolting and a chance to determine the root causes of it. The Shox Box system reviews data in real time, onboard the vehicles, 24 hrs a day, and sends pertinent information via radio to a central database. The data generated shows whether jolts are above or below a supervisor defined target value for the equipment and the tasks being performed. This allows health and safety personnel to demonstrate safe operation of heavy equipment and recommend proactive actions to maintain jolting within a reasonable range.