Search Documents

By G. T. Pruitt, T. L. Irby, P. B. Crawford, H. Ferrell

In water flooding peripheral, center-to-edge, line-drive or water-encroachment patterns the question has arisen, "when should a producing well be converted to a water-injection well?". It is realized that, if the producing well is shut in when water breakthrough occurs, some oil could be left in an unswept area. Yet, operation to high water-oil ratios may require processing much additional water. If a well is shut in, "where should the allowable be transferred?". A review of the literature indicates that very few data are available to the engineer to assist him in answering these questions. It is the purpose of this paper to present information which may be of value in selecting the flooding technique and the injection and producing wells and in scheduling injection and production rates. Certain phases of these problems can be studied in the laboratory. The Potentiometric model is well suited for studying many waterflooding problems. This model assumes that steady-state flow exists, that the mobility ratio is equal to one and that gravitational effects are neglected.'-' The three-phase sand model also has been recognized as an effective means for studying certain reservoir problems. Both models were used in making the study reported here. This paper discusses seven cases utilizing various waterflooding techniques. Data for the first five cases were obtained on the potentiometric model. Data for Cases VI and VII were obtained by constructing and flooding an unconsolidated sand pack (a three-fluid-phase system) and by determining the swept area and cumulative oil recovery for various types of operations. APPARATUS AND PROCEDURE The potentiometric model reservoir was 30 in. long X 10 in. wide by about 1/2 in. deep. Four wells were equally spaced in a line array along the lateral center line. (See Fig. 1.) Well No. 1 initially was an injection well for each of the patterns reported. The cases studied with the potentiometric model and sand model are described herein. The laboratory sand model reservoir was a 30- 10-in. rectangular Lucite vessel packed with sand to a depth of about 0.65 in. Four wells were equally spaced in a line array along the lateral center line. The reservoir material was an unconsolidated sand into which the reservoir fluids were mixed to yield fluid saturations of 55 per cent oil, 25 per cent water and 20 per cent gas. The water was added to the sand and the material mixed, after which the oil was added. Kerosene and water, the fluids used, gave a viscosity ratio of 1.64:1. In packing the reservoir, care was taken to assure constant fluid saturations and constant porosities. A new mixture was prepared for each run. During water flooding, a colored water was injected by a constant rate pump. The injection rate was 1.1 B/D/ft of sand thickness. For this series of tests, each of the producing wells was open to the atmosphere and, as in the potentiometric model study, Well No. 1 initially was an injection well for each of the patterns. KESULTS OF POTENTIOMETKIC MODEL STUDlES Two cases (Cases I and 11) involving equal pressure injections were studied, with the following results. Case Water injection was initiated at Well No. 1; the producing wells (Nos. 2, 3 and 4) were operated at constant and equal bottom-hole pressures. When water broke through at Well No. 2 and achieved the selected water-oil ratio, Well 2 was converted to a water injection well, resulting in two injection and two producing wells. The injection pressures at Wells 1 and 2 were maintained equal and constant; pressures at the producing wells were held equal, but they were lower than those at the injecting wells. A similar process was repeated when water broke through at Well No. 3. The flood was terminated when

By Sayan Sarkar

HAMR (Hydrogen Assisted Magnesiothermic Reduction) process is a promising alternative route of titanium production, which is convenient due to reduction at relatively lower temperatures below 750 °C and usage of cost-efficient TiO2 as the starting material. A crucial step involved in this process requires the Mg reduction of TiO2 subjected to H2 atmosphere which produces porous TiH2 along with residual magnesium impurities. Before the final heat treatment and deoxygenation steps for consolidation of the Ti powder, leaching plays a significant role in the removal of Mg impurities. In this report, we present a systematic study on the role of acid concentration (HCl), temperature and the kinetics of MgO dissolution. In addition, we also report the controlling mechanism during kinetics of MgO dissolution in acid. This parametric study will provide a platform to ensure very low Mg content that meets with ASTM standards during production of Ti in the HAMR process.

By Christiana Mystrioti

Greece is the only EU country with extensive nickel laterite deposits. Since the 1960s, the Greek laterites are treated for ferronickel production via a pyrometallurgical route, which involves pre-reduction of the ore in rotary kilns and reduction smelting in electric arc furnaces. Due to the rising cost of energy and the decreasing grade of mined laterites, the pyrometallurgical treatment is economically marginal. For this reason, alternative treatment processes are currently under investigation. Potential applicability of hydrometallurgical treatment, using either H2SO4 or HCl, under atmospheric pressure conditions, for Ni and Co extraction from two low grade laterite ores, was examined in the present work. The two samples were selected to represent the different mineralogical composition of the saprolitic and limonitic ore deposits of the Greek laterites. The investigated parameters were temperature (65–90 °C), acid concentration (1–4 N) and solid to liquid ratio (10–30% w/v). The results indicated that HCl was more efficient than H2SO4 for the treatment of the saprolitic ore; Ni and Co extractions were very high for both elements, up to 98% and 96% respectively, while H2SO4 could leach efficiently Ni, up to 100%, but extracted only 34% of Co. Hydrochloric acid was also more efficient for the treatment of the limonitic ore, with Ni and Co extractions up to 98.3% and 87.6% respectively. With H2SO4 the maximum extractions were 71.3% for Ni and 52.1% for Co.

By Bien Ferrer

In most smelting operations, there is a strong incentive to improve safety, reduce downtime and extend the campaigns of furnaces and related equipment. An asset management strategy that is based on information, rather than simple throughput metrics and intuition, can be developed to improve uptime and unlock value currently unrealized at existing smelters. Advances in digital technology, including data analysis, modelling and monitoring for hot pyro-metallurgical vessels, make it possible to assess the current condition of an asset, as well as to make more informed projections about its future condition, using on-line and historical data. This would allow practices around asset management to be more proactive and less reactive, with the end-result of optimized uptime. ‘Digital Asset Management’ describes a concept in which digital technology is used to support an asset management strategy and accelerate decision-making by providing information on what, why and how an asset should be designed, operated or maintained. With the overall goals of effective resource utilization, optimized operations, capital efficiency and social acceptance, Smelter 4.0 is a program of holistic improvement and is underpinned by the effective use of data to drive decisions. This paper focuses on Asset Reliability, which is one of the improvement pillars of Smelter 4.0, and introduces a methodology that is aimed at closing the gap between recorded data and evidence-based decision-making through Digital Asset Management.

By Wynand Erasmus, Terry A. Jones

The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals. The KCJ has been successfully employed in mineral sands applications in Australia for approximately 12 years. More recently, the KCJ has been tested and installed on zircon tailings dump retreatment projects in Australia and the USA, while being considered for similar projects in RSA, and is about to be installed in zircon tailings processing duties in India and Africa and in a tin removal duty in a rutile circuit in Australia. Extensive test work has been carried out on these applications and some typical performance data is presented in this paper. Information is also provided on the principles of operation of the KCJ and on the keys to a successful KCJ installation.

By Rodney Clary

Building on work completed in earlier papers, the current paper presents a techno-economic evaluation of two recently demonstrated technologies for treatment of arsenic containing refractory gold concentrates. Using defined project parameters and inputs, the authors compare capital and operating cost estimates for pressure oxidation (POx), and the Albion Process™. The paper incorporates data now publicly available from the Albion Process™ plant, which has operated at the GeoProMining Gold (GPM Gold) project in Armenia since 2014, as well as recent POx circuits.

By Yun Li

An innovative lead recycling process from scrap lead-acid battery paste is presented. The novelty in the process is avoiding SO2 generation and emission by using reductive sulfur-fixing technique. Iron-bearing secondary wastes produced from metallurgical industry were utilized as sulfur-fixing agent to capture sulfur in the form of FeS (s) instead of generation of SO2 (g). Na2CO3 molten salt was added to the smelting system to speed the reactions and improve valuable metals’ recovery and sulfur-fixation efficiency. Furthermore, this process can simultaneously co-treat various lead and iron-bearing wastes. At the same time, some precious metals, such as Au and Ag, contained in iron-bearing wastes can be recovered. The feasibility and reliability of this process was investigated thermodynamically and experimentally with the help of HSC 9.0 database and XRD and SEM-EDS analysis. A possible reaction mechanism and path in PbSO4–Fe2O3–Na2CO3–C smelting system was also clarified.

By F. W. Jessen, N. Mungan

The plastic flow characteristics of clay water suspensions were first recognized by Binghaml in 1916 and further studied by Ambrose and Loomis' in 1931-1932. Many physical and chemical properties of clay suspensions are deeply influenced by particle size distribution as well as by the exchange cation. Separation of a number of fractions is particularly helpful in making a detailed study of a suspension. A limited amount of work has been conducted on the effects of particle size on specific properties of mud drilling fluids. A knowledge of particle size distribution is essential for a better understanding of fundamental properties of clay suspensions, particularly viscosity and gel strength. The purpose of this investigation was to study the effect of particle size on the viscosity and gel properties of clay suspensions and to determine any changes in mineral composition accompanying variation in size. EXPERIMENTAL PROCEDURE Numerous methods may be used to fractionate a poly-dispersed clay suspension into nearly mono-dispersed systems. Particles larger than 44 micron (325-mesh) may be obtained by wet screening. For sizes from 44 to 1 micron, the fractionation may be accomplished by sedimentation, elutriation plus microscopy,' or turbidimetry.6 When dealing with systems which contain a major portion of particles below l-mi-cron size, slit ultramicroscopy,7 centrifuge methods of Svedberg,5 eams,9 and McBain,l0 and X-ray methods" may be employed. The Sharples super centrifuge has been proved suitable for the economical separation of suspended particles of submicron range.12,13,14 Three-hundred and forty-five gal of 1 per cent by weight Aquagel suspension was mixed in a high-speed 5-gallon mud mixer and the suspension was allowed to stand in 5-gal glass bottles for 30 days to assure full hydration. All particles larger than 44 microns were removed by wet screening. Five fractions in the range of 44 to 1 micron were obtained by sedimentation. The Sharples super centrifuge method described by Hauser and Reed.13 Norton and Speil,14 Ha user and Lynn,15 and Hauser and Schachman,10 as employed to yield five fractions of submicron size. A super centrifuge operation chart prepared by Fancher, Oliphant, and Houssierre12 was used to determine operating conditions for the desired particle ranges. The clay suspension, after removal of all material above 1-micron size, was centrifuged. During rotation of the bowl, the particles were deposited on a thin plastic liner which fit closely inside the bowl. After passing 5 gal of suspension through the centrifuge, the liner was removed and the particles on the liner were scraped off, remixed and recentrifuged. This was repeated five times. Thus, Fractions H, I, K, and L were obtained. The finest fraction, M, remained in an approximately 0.4 per cent suspension. Water was evaporated under reduced pressure from this suspension to yield the finest particles. Results of the fractionation are included in Table 1. In order to achieve proper orientation and humidity conditions for X-ray diffraction analysis, the following procedure was employed. The dilute suspensions were placed on glass slides and allowed to dry at room temperature. This was repeated several times. Previous to measurement each sample first was placed in a water desiccator for half an hour and then allowed to stand for 15 minutes at room temperature. thus yielding an equilibrium condition of about 52 per cent relative humidity. The relative humidity of the room in which the X-ray diffraction was carried out was maintained at approximately 50 per cent so that there was no change in the spacings during the X-ray examination. Samples

By Frank E. Chase, John L. Ellenberger, Christopher Mark

The nature of competition in the coal market tends to deplete the most favorable coal reserves first, and forces subsequent development of mines in more extreme ground conditions such as those associated with multiple-seam mining. In fact, 70% of the United States coal reserves are in multiple-seam situations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop mine design algorithms that will result in safer multiple seam mines. This paper presents an overview of multiple seam issues in the central Appalachian coalfields. To date, more than 50 case histories have been analyzed from 20 operating mines in Eastern KY, Western VA, and Southern WV. Each case history is classified according to the degree of multiple-seam interaction, ranging from no apparent interaction to severe interaction with direct impacts on mine safety and resource recovery. The case histories are also examined with regard to amount and geologic characteristics of interburden and overburden, and design stability factors. The sequence of mining has also been found to be critical when the lower seam is fully-extracted. This paper compares current case histories to traditional rules of thumb. In addition two situations were modeled using LaModel software. LaModel has been upgraded to import pillar grids and topographic data from AutoCAD files. The cases presented demonstrate vertical stress capabilities of LaModel.

By Mike Dry

Conventionally, lithium-bearing brines are processed via solar evaporation, chemical purification, and either electrolysis to lithium hydroxide or precipitation of lithium carbonate. Lithium-ion battery technology and electric vehicles are forecast to greatly increase the demand for lithium, but not all lithium-bearing brines are amenable to the conventional extraction process and new approaches are being developed. The chemistry associated with conventional lithium extraction is outlined and two new approaches are discussed.

By V. Blet

Rare earth elements (REE) are regarded today as highly critical raw materials but currently lack suitable recycling processes. A combined hydro- and pyrometallurgical process aimed at REE recovery from used NdFeB permanent magnets was recently developed by the CEA. The process integrates the physico-chemical treatment of magnets, followed by a solvent extraction step for the recovery and intra-REE separation using a selective extractant. A subsequent pyrometallurgical treatment via molten chloride salt electrolysis allowed the isolation of pure Dy metal. Technical-economic assessment and life-cycle analysis were also conducted. Following this first successful demonstration, a new project aimed at the recovery of REE from end-of-life nickel-metal-hydride batteries is currently being developed in association with industrial and academic partners. The project aims at evaluating from an experimental and economic perspective different processes converging at the production of value-added products such as cermet materials for catalytic applications, purified REO concentrates, or metallic alloys.

By W. Hurst

What is entailed here is the extension of the sinzplified material balance formulas to encompass interference between oil fields. As previously reported, the ex-plicitness as so revealed for the cunzulative pressure drop as a function of all factors contributing to its change in the material balance equation, is now transcribed through the inter-conzmunicating aquifer to effect an increased pressure drop on an adjoining field by interference. Such is performed by mathematical analyses and the application of the Laplace transformations. What is accomplished is that the reiteration problems previously associated with interference studies are nullified, since volumetric changes for the fluids in situ are automatically adjusted by the explicitness so expressed, and what pertains to the superposition principle applies only to the impeded water drive upon a su.bject field, which is likewise incorporated in the over-all pressure drop that results. The mathematics treats with the rigorous solution of the problem, as well as with methods easily amenable to numerical interpretation by the practicing engineer. In all cases, however, what is deduced for areal extents, reveal interference between wells when time becomes large that further substantiate the analyses. Probably of equal significance, all variables and for/nation characteristics are accounted for. This applies to the differences in PVT analyses that occur from field to field and the physical parameters associated with the lithology of the reservoirs. The latter is deduced from a rigorous interpretation of the unsteady-state flow problem for sands of different permeabilities in series. Thus, what purports to be a trial-and-error calculation to include variations in sand conditions within the intercommunicating aquifer to define water drive has little importance compared to the designation of such paranzeters at the reservoir to constitute the essential criteria. INTRODUCTION In a recent publication, the reader has been introduced to the simplified material balance formulas,' It has been shown that the complexities formerly associated for identifying and determining reservoir pressure in the material balance relationship can be resolved by treating with the Laplace transformations, the inversion of which reveals pressure as an explicit function of all factors contributing to its change. For an under saturated oil reservoir, this constitutes an integrated effect from the inception of production; and for a saturated oil reservoir, such represents a survey traverse. However, what is most important, for the first time we are able to express the pressure change in a reservoir directly to the oil, gas and water produced, and to the physical parameters of the formation, in the same manner that reservoir pressure has served in the past to define well interference — which opens up this avenue of endeavor for investigating interference between oil fields. The occurrence of interference is by virtue of the juxtaposition of two or more oil reservoirs producing in the same aquifer. Thus, in any one field, the extended production so incurred creates a pressure lowering in the field, as well as in the aquifer, which can now be transcribed by these simplified material balance formulas to the adjoining reservoir to observe the increased pressure change so induced. These effects are retroactive from field to field, to reveal a pressure drop far in excess of normal depletion to evidence the interference pattern that can result. Such is the purpose for the present undertaking — to develop the mathematical physics treating with this phenomenon of interference between oil fields, employing the simplified material balance formulas. Since Ref. 1 often will be referred to in the text, it is identified as "The Simplification", in the same connotation that another paper has been referred to as the "Laplace Trans-formation. However, the amount of material to be covered in these passages is substantial; therefore, the total emphasis will be placed upon developing these fundamental ideas treating with interference rather than attempting to offer work curves, which always can be prepared. For the practical application of these simplified material balance formulas that form the framework of the present development, the reader will find a comprehensive treatment in the Appendix of Ref. 1, illustrating a factual field example. In essence, what is proposed by this presentation is to make available to the practicing engineer a simplified means to treat with interference between oil fields, independent of the complex machine computations that have attended such undertakings in the past. As the problem unfolds, a common pattern will be discernible, whereby the many reiteration processes that previously required computing devices are eliminated.

By R. Karl Zipf, Christopher Mark

Highwall mining continues to grow in importance as a coal production method from U.S. surface mines. It may account for as much as 4% of the total U.S. coal production, according to one recent estimate. Analysis of Mine Safety and Health Administration (MSHA) accident and injury statistics shows that, overall, highwall mining has maintained an admirable safety record. Its fatality and injury rates are comparable to those for other surface mining methods, and are significantly lower than those for underground mining. No mining method is risk free, however. Highwall mining injuries have been associated with handling materials, slips and falls, machinery, powered haulage, and other types of incidents. But perhaps the greatest risk, to both personnel and equipment, is from ground control. The two most significant ground control hazards are rock falls from the highwall and equipment entrapment underground. Highwall Stability Ensuring highwall stability through proper ground control engineering is of paramount importance to safe highwall mining operations. The only fatality to occur during the last five years at a highwall mining operation was due to highwall collapse. There have also been numerous near-misses, several of which have involved extensive damage to equipment. In the central Appalachians, where the majority of highwall mining occurs in the U.S., hillseams are the most prominent geologic structures that affect highwall stability. Hillseams (or mountain cracks) are near vertical fractures in the rock that are formed in response to natural weathering and erosion of hillsides. They extend hundreds of feet down from the surface. They typically run parallel to the hillside, but they can also extend across narrow points or ridge lines. The hazard arises when rock slabs that form along the hillseams detach and fall away from the highwall face (See Figure 1). [ ] Unfortunately, it is impossible to control the location of hillseams or reliably detect their presence within a highwall. There are, however, a number of measures that can be taken to minimize the risk of failure associated with hillseams: Planning-Most operators choose to skip those areas of the highwall where a prominent hillseam daylights (See Figure 2). Existence of such areas is known for several weeks in advance of highwall mining; therefore, planning engineers can adjust the layout of highwall mining panels to locate barrier pillars within areas of questionable highwall stability. [ ] Inspection and monitoring-Daily inspection of the benches above the active highwall mining area is a prudent precautionary measure. A crack in a bench immediately above a highwall miner is shown in Figure 3. Simple displacement monitors may be useful for detecting movement along cracks that may precede a significant life-threatening failure. New tools, such as slope monitoring radar, may also prove useful in detecting motion of the rock slopes above active highwall mining operations. Good blasting practice-Most surface coal miners in the central Appalachians use pre-splitting and the familiar halfbarrels are routinely seen throughout the pits. Shorter delays along the face and longer delays between rows can direct more of the blast force parallel to the face, potentially doing less damage to the wall rock. In addition to pre-splitting, decreasing the burden, spacing and charge weight in drill holes close to the highwall will also decrease damage to the wall rock. Decreasing the highwall slope angle-Decreasing the highwall slope angle from 90° (vertical) to 70°-80°, especially in areas of known hillseam concentration, could eliminate the hillseam hazard (See Figure 4). Angled highwalls are routinely employed in many Midwestern surface mines and in some

By Sean Gallagher, William S. Marras, Alan S. Litsky, Deborah Burr

This paper describes a comparison of the fatigue failure responses of older versus younger lumbar spine cadaver motion segment specimens. These specimens were repeatedly subjected to loads simulating those experienced by the spine in lifting a 9 kg load in different torso flexion postures (0, 22.5, and 45 degrees of flexion). An older sample of 36 motion segments (average age 81 years + 8 SD) is compared with a younger sample of 18 motion segments (average age: 47 years + 9 SD) with respect to the number of cycles to failure and results of survival analyses evaluating the effects of flexion and bone mineral content with and without the younger data set. Compared to the older sample of spines, the younger sample exhibited many more cycles to fatigue failure in all the torso flexion conditions (10020 versus 8267 average cycles to failure in 0 degrees flexion, 7124 versus 3262 in 22.5 degrees flexion, and 3229 versus 263 cycles to failure in 45 degrees flexion). The increased cycles to failure in young specimens is likely due to the increased bone mineral content (BMC) in younger motion segments (30.7 g + 11.1 g per motion segment versus 27.8 + 9.4 g). Cox regression analyses modeling both flexion effects and BMC indicate that betas are similar when just older spines are modeled and when younger specimens are included in the analysis. Betas for survival analysis models with and without younger specimens generally show little change for flexion (2.716 versus 2.756 for 22.5 degrees [0 degrees referent], 3.926 versus 3.380 for 45 degrees [0 degrees referent]). Bone mineral content shows a similar protective effect in both models (Betas: -0.127 versus -0.087). Overall, comparison of the models indicate that risk ratios are similar for 22.5 degrees flexion, slightly increased for 45 degrees flexion and slightly more protective influence predicted for BMC in the combined sample versus the older sample alone.

By J. J. Arps

n approach to the study of the electrical properlies of drilling muds, their cakes and their filtrates was made by treating the drilling fluid as a porous medium. Lluring this study it was found that the weight pararneter was omitted from previous investigations on electrical properties. Patnode in 1949 made a similar approach to ,his investigation. His work showed that there was a variation of resistivity relationships with per cent Puid present in a given suspension. This present study ex-tends Patnode's investigation to one in terms of the solids fraction of the drilling fluids. Previous investigations were made on low weight muds where the effect of the rolids fraction was obscured. The following equationr were fitted to data taken from 94 field muds and 47 laboratory muds (see Tables I and 2). The parameter, C, is a complex function of the solidr content, or mud weight, of a drilling fluid. It was also found that for all drilling muds examined. A nomograph is presented combining Eqs. I and 2. INTRODUCTION It is generally recognized that the materials present in drilling muds affect the relationship between mud filtrate and mud resistivities. However, most electric log interpretations proceed with the assumption that the mud resistivity and temperature are the only important parameters needed to obtain a filtrate resistivity or a mud cake resistivity. Lamont1 suggests that only average relationships exist between mud cake, mud filtrate and mud resistivities. He indicates that there is limited accuracy when these intercorrelated factors are used since no other measure-able variable is apparent. A previous paper by Patnode indicates that drilling fluids may be considered to be a system of fluids in solid particles which may be correlated electrically in a manner similar to rock solids. 1 he equation for the resistivity factor. F = (per cent fluid) is satisfied for a given clay type in water, but the value of m varies as different materials are used in the water. The resistivity factor is not constant for a given amount of clay. As is suspected it varies as the solids fraction conducts electrical current. Since both weighting material and clay solids are present in commonly used drilling fluids, it is expected that both materials contribute to the variation of the m factor in Eq. 3. An extension of Patnode's work is presented in this paper to show some of the interrelations which exist between the resistivities of mud cake, mud filtrate and mud. Use of these data enable a more accurate calculation of mud filtrate and mud cake resistivities if only the mud resistivity and weight are measured. EXPERIMENTAL The measurements of mud weight, fluid and solids resistivity, alkalinity, and chloride content of mud samples were made in this research. Mud samples representing drilling fluids from 94 Louisiana and Texas wells (Table 1) and 47 laboratory-constructed systems (Table 2) were used in the experimentation. The measurements of the mud properties were made both in the field and in the laboratory. The tests on the properties of weight, alkalinity and chloride ion were standard tests as described by API specifications. The resistivity measuring devices were constructed in the laboratory for this study. For details on the resistivity equipment see Fig. 1. The fluid cell

USBM Contract H0133045 consists of the design, build and test of 50 waveform generators. The waveform generator is a small ULF transmitter operating in the 1 to 3 KHz frequency range for the purpose of locating trapped miners during a mine disaster. This contract provided for the design, test, and building of 50 waveform generators using a discrete component construction with an option of using hybrid construction techniques within 105 days after the effective date of the contract. Because of large quantity economic considerations, this option was not initiated. Two engineering models were designed, constructed and tested and 50 final production units were fabricated using discrete construction. Complete documentation is supplied under a separate package which includes final schematics, parts list, layout information, equipment specification, production test procedures and qualification test procedures. Ten units have been delivered to the USBM. The remaining 40 units are being retained for packaging under contract H0242010 Transmitter Package and Receivers. A great deal of experience has been gained as a result of this contract. A final discrete potted printed circuit configuration has been arrived at that is now ready for field testing. After field testing, any desired changes should be incorporated into a final design. However, as a result of the current experience gained building and testing the production units, this printed circuit package together with potting procedure could be improved to reduce future costs. For example, the printed circuit board could be increased in size by 0.125 to 0.2 inches and all components could be mounted directly to the board eliminating costly hand stacking of components. The new printed

By Yan Zeng

Lithium metal silicates (Li2MSiO4, M = Fe or Mn) composed of abundant and non-toxic elements are important cathode materials for Li-ion batteries (LIB). In contrast to solid-state or sol-gel methods, hydrothermal synthesis conducted in pressure reactors is a favorable processing route as it provides the potential for scalable production and is environmentally benign. However, the key is to control the precipitation reaction to obtain powders with desired properties to meet battery specifications. Through a systematic study, we have found that Li2MSiO4 with tunable size from 300 nm to 1.5 μm can be produced by adjusting precursor concentrations, temperature, and reaction time. Under optimum conditions, high purity Li2MSiO4 with minimum defects were successfully produced and examined as an LIB cathode. The use of complexing agents promoted the formation of unique hollow particles via the self-assembling of elongated crystals. A four-step formation mechanism is proposed based on extensive characterizations with XRD, HR-TEM, SEM, and Mössbauer spectroscopy.

By Jean-François Boulanger

The production of rare earth elements from ore usually consists of three steps; the separation of a concentrate of REE bearing minerals; the cracking of the REE minerals to liberate the REE into an aqueous solution and separation of REE into individual elements. This paper describes the results of laboratory tests conducted on a carbonate-rich REE ore containing bastnaesite and monazite. The tests cover the whole processing sequence of beneficiation, preparation of the REE solution using a caustic leach followed by acid leach to break monazite and bastnaesite and liberate REE into an aqueous solution and the partial separation of the REE using solvent extraction. Details on the product quality and process performances (recovery and impurities removal) are given for each studied step. The paper also discusses the economic advantage of separating the REE rather than producing a mixed REO product to be sold to a refinery for REE separation. A mini-pilot plant version of the process is currently planned.

By C. S. Matthews, G. L. Stegemeier

In one field in South Texas, approximately 72 per cent of the pressure build-up results show a characteris-i.rtic "hump" (i.e., the pressure builds up and then falls off) which makes interpretation by. standard methods impossible Correlation of size and time of hump with formation permeability. well productivitv index, and method of completion led to the tentativc, conclusion that the humps were caused by segregation of gas and oil in the wellbore after closing-in"'. This conclusion was confirmed by performance of simple laboratory bubble-rise experiments, by theoretical bubble-rise time calculations, and by a detailed calculation of PVT behavior in the well of a particular well Oil which accurate Surface and bottom-hole pressure measure-ments were untile. The hump behavior has since been found to occur in many other fields. The cause, however, is not the mine in all cases. In some of these the hump is trace-ahie to leaks in the tnbing which allow influx from the annulus after closing-in. In other cases the hump is traceable to leaks in the device separating pay horizons in dually completed wells. It is concluded that the recording of both surface and bottom-hole pressures is desirable in wells which show an anomalous build-up behavior. A number of field examples is discussed where use of both sets of measurements enables the cause for anomalous behavior to he found, (and a reasonable interpreation of bottom-hole pressure to be made. INTRODUCTION Theoretically the pressure build-up in an infinite reser-voir should be a linear function of In [(t + at)/nere t is the production time and At a the closed-in time. Some of the variations from this behavior arc well known, such as the curved portion immediately after shut-in which results from after-production and skin effect, and the flattened end portion which results from boundary effects in a limited reservoir. The effect of stratified producing zones and irregular geometrical drainage patterns may also contribute unusual characteristics to build-ups. However, the effect of still another phenomenon—that of movement of fluids within the wellbore—has been neglected in most build-up studies to date. Fluid movements within the wellbore after shut-in occur as a result of after-production, packer failures, leaks in the casing or tubing, or buoyancy of the gas phase when both gas and liquid are present in the well. Each of these movements can influence the pressure build-up, sometimes sufficiently to negate use of the data for computing permeability or stabilized build-up pressure. Examples of each of these phenomena are discussed below. FIELD OBSERVATIONS ON HUMP BUILD-UPS In approximately 75 per cent of the wells in a medium-sized field in South Texas the pressure build-up curves rise to 3 maximum and then decline to what appears to be a stabilized reservoir pressure as shown in Fig. I. Similar behavior has also been observed in wells in other fields in Texas and Louisian:,. Because of the possibility of such behavior being a mechanical failure of the pressure bomb. the bombs were run in tanden into one well which had been known to exhibit this behavior. When both bombs recorded identical curves with the characteristic hump, it was inferred that the unusual build-up is a result of well or forma-

By J. A. Organiscak

This paper examines methods for limiting occupational silica exposures for roof bolting personnel in underground coal mining. A canopy air curtain and an air tube were evaluated as means to provide filtered air over the breathing zone of these personnel. Laboratory testing showed that dust reductions beneath the air curtain and air tube approached 60 percent and 40 percent, respectively, with low interference air velocities. The data also showed that dust reductions were highest for positions closest to the device and that these levels decreased with distance. This paper also evaluates a metal rake, a flexible insert, and a rigid insert for cleaning the roof bolter dust collector box. Less dust was produced when using the rigid insert. Surprisingly, the flexible insert was sometimes no better than scraping or raking the dust onto the mine floor. However, little dust got on the coveralls when using either of the inserts.