Search Documents

By M. D. Aldridge

This document reports the results of a two-year research effort aimed at improving communication systems used in coal mines. This work was conducted under a program whose original goal not only involved the development of practical and effective electronic systems for operational communications, but also for monitoring, at a central location, remote instruments at key positions in a mine. About half way through the originally proposed three year effort, the program was redirected to phase out the communication effort at the end of two years and to concentrate the program" resources on the investigation of new monitoring system concepts developed by this research. Thus, the work reported here is incomplete relative to the originally pro- posed program. However, the work was carried to the point of providing sufficient evidence to aid in the comparison of certain new communication concepts. For the concepts chosen for this study, the work was stopped short of hardware development and field testing, Several reports in the form of Master's theses and a Doctoral Dissertation have resulted from this research. They each report in considerable detail the results of several individual" contributions to this program. In preparing this report, an attempt has been made to provide a complete description of the significant results but with- out burdening the reader with the minute details. These more detailed reports are referenced heavily for the convenience of those interested. PRESENT COMMUNICATION METHODS Two types of communication systems are presently used In coal mines. They are: 1, Various forms of telephone systems, and 2. Carrier current radio systems using the trolley line as the interconnection circuit. Carrier current radio is used almost exclusively for control of rail trafflc by the dispatcher. Almost all other communication uses the telephone system, Telephone lines generally extend to areas where trolley lines are not present such as the outside offices and warehouse. Therefore the telephone system provides the primary means of voice communication. Telephones - Telephone systems employed in American coal mines fall into three categories. 1. Paging type telephone systems - these systems have individual stations which use battery powered transistor audio amplifiers to boost signal levels for normal communication. When in the page mode,

By J. R. Goode

Up to one half of neodymium and praseodymium production, key ingredients in permanent magnets, is produced illegally. About 60% of cobalt production, critical in lithium-ion batteries and other applications, comes from central African states, and much of it is produced illegally. Tantalum, important in modern electronics, is also primarily sourced from central Africa and, again, much of it illegally. Illegal mineral production, as exemplified here, is often used to fund armed conflict. Furthermore, it is typically conducted with scant regard for human rights and environmental protection. It also leads to depressed prices which in turn limits the possibility of legitimate producers entering the market. Systems of traceability and provenance, along with cooperative supply chain participants can limit the production of illegitimate material and thereby improve conditions in the countries of origin and reduce downward pressure on prices.

By W. R. Reed

Drilling with water has the potential to significantly reduce the respirable dust concentrations generated from small-diameter rotary drills when drilling blastholes on surface mining operations. However, water adverseky affects tri- cone drill bits commonly used in surface drilling operations, causing excessive wear and premature replacement. Consequently, dry drilling with a dust collector system has the most widespread use in the industry. Tests have been conducted by the National Institute of Occupational Safety and Health (NOSH), Pittsburgh Research Laboratory (PRL) on a newly designed device for smaller diameter drills that separates the water from the bailing air before it reaches the bit and thus provides the cost benefit of dry drilling while providing the benefit of wet drilling for dust suppression. The water that is delivered to the hole with the bailing air is separated from the air by a proprietary mechanical device that is encased in a drill sub (short section of drill rod/pipe) located immediately behind the cutting bit. A cascade cyclone and a real-time dust monitor were used to sample dust emissions from the holes. Dust concentrations and silica content were measured when drilling dry versus drilling wet. The tests show that drilling with this water separating sub can reduce both measured dust emissions from the boreholes and visible dust around the drill rig.

By A. Lubinski, W. D. Greenfield

Bumper subs are currently used in offshore operations to permit a constant weight to be carried on the bit while drilling, regardless of the vertical motion imparted to the drill pipe by drilling vessel heave. As shown in this paper. the vertical motion of the lower end of the drill pipe (the bumper sub end) may be appreciably greater than the vessel heave. Therefore, the necessary stroke of bumper .rubs for successful operation is greater than thought in fie past. Also, there is an appreciable tendency of the drill pipe to buckle above the unbalanced type of bumper sub. Thus, more drill collars than previously used should be carried above unbalanced bumper subs to keep drill pipe straight. INTRODUCTION Drilling bumper subs are placed in the drilling string for various reasons. This paper is concerned with their use only as an expansion and contraction joint while drilling from a floating rig. In this application the bumper subs are normally located just above the drill collars and their function is to allow the driller to maintain accurate weight control on the bit regardless of up-and-down movement of the drilling vessel. This paper analyzes the effects of bumper subs on the drilling string and presents recommendations for their future use. When subjected to vertical oscillations, the drilling string behaves like a long, distributed system of mass and spring. The magnitude of vertical motion at the bumper sub is always greater than the heave of the drilling vessel due to the dynamic reponse of the drilling string. The ratio of these motions increases with the length of the drilling string, and may reach values of 1.5 or even 2 with strings 16,000 ft long. Thus, the total travel required in bumper subs can be considerably more than the motion of the drilling vessel. Lack of knowledge of this fact could have contributed to problems previously experienced with bumper subs. This fact can also lead to fatigue problems in the drilling string for very deep wells. Satisfactory operation should be obtainable whether hy-draulically balanced or unbalanced bumper subs are used in the drilling string. Theoretically, the balanced sub is preferable since its use does not require placing drill collars above the bumper sub to prevent drill-pipe buckling, an inherent characteristic of the unbalanced bumper sub. The current method of calculating weight of drill collars required to prevent helical buckling of drill pipe above unbalanced bumper subs is erroneous. Placing drill collars above the sub to prevent drill-pipe buckling has the same effect on dynamic response as increasing the length of the drilling string by an equal weight of drill pipe. Thus, total travel required in the subs is increased. Means for calculating the correct weight, which is much greater than previously thought, are given in this paper. BALANCED VS UNBALANCED BUMPER SUBS A drilling bumper sub is essentially a telescopic joint capable of transmitting torque at every position of its stroke. Thus, it allows the operator to isolate the weight of the drilling string from the weight of the drill collars above the bit. This permits the driller on a floating rig to maintain accurate control over the weight on bit — a control that is unaffected by vertical motion, due to wave and tide action of the drilling vessel. UNBALANCED BUMPER SUBS The unbalanced bumper sub is simply a splined tele~copic joint (Fig. I). Ordinarily, this arrangement will operate satisfactorily, but the presence of drilling fluid under pressure results in a pressure force that acts downward on the drill collars and bit, tending to open or extend the bumper sub. This downward force is equal to the pressure drop across the bit times the area indicated by diameter d2 in Fig. 1. Denoting this force by Fd, and the pressure drop across the bit by ?p yields Fb = (p/4)d22(?P) .........(1) There is also an upward-directed force given by Fu = (p/4) d22-d21)(?p) .......(2) which puts the drill pipe immediately above the bumper sub in compression, resulting in helical buckling. However, buckling is actually more severe than expected in that buckling occurs as if the compression were equal to Fd, rather than to Fu. This surprising phenomenon is well known as far as tubing is concerned;1-3 but, in contrast with the case of tubing, this force may shorten drill pipe only a few inches. Thus, this cannot explain the operating difficulties that sometimes have been encountered. However, having the drill pipe in compression and helically buckled is contrary to current practice; therefore, drill collars whose weight in mud is equal to the force Fd should be added above the bumper sub. Since the value of Fd depends on the pressure drop across the bit, the

By Donald J. Olson

The North 27th St. ISS Extension tunnel will, under present plans, be the last constructed section of Milwaukee Metropolitan Sewerage District?s (MMSD?s) existing deep tunnel system. The 6.5 m (21 ft) finished diameter tunnel is approximately 3,260 m (10,590 ft) long and is located in NE Milwaukee County. When disputes over the pro-cesses to be used in owner-directed pre-excavation grouting in rock threatened the completion date stipulated between MMSD and the State of Wisconsin, the MMSD and J.F. Shea, the contractor, entered into a unique agreement. Shea accepted responsibility for all shaft and tunnel grouting and water control during the project in exchange for settlement of claims related to grout quantities and perceived delays. This significantly reduced risk for the MMSD and helped ensure the stipulated completion of the project.

By Jiakai Zhang

Many postconsumer electrical and electronic equipment wastes contain a considerable amount of rare earth elements (REEs); however, the current level of REE recycling from them is limited (<1%). Neodymium–iron–boron (NdFeB) magnets, used at both small- and large-scale, from computer hard disk drives and small tools to wind turbines and cars, are a good example of such waste materials that contain high content of neodymium (Nd) and dysprosium (Dy). These elements are considered critical metals because they are the main building block of emerging green technologies that will allow for GHG emission reductions. Because demand for these green products is increasing around the world, the demand for REEs is increasing quickly, putting their supply at risk in the near future. Thus, it is critical to develop efficient, robust, and cost-effective processes to recycle these elements from this class of electronic waste materials. Here, we performed a thorough characterization of a N52–NdFeB magnet to identify its composition, crystal structure, and morphology. Furthermore, we developed an efficient hydrometallurgical process to extract Nd and Dy with high efficiency (more than 95%).

By W. S. Ayres

By D. Gregurek

In non-ferrous metal furnaces the installed magnesia-chromite refractory lining is exposed to several stresses, rather complex in their interaction. Therefore, a detailed investigation and understanding of wear mechanisms through “post mortem studies” is an important prerequisite for refractory producer. Additionally, in order to determine the most suitable refractory products and to improve the lining life of refractories, practical corrosion testing with processing slags is performed. For this purpose the test-facilities, such as induction furnace, rotary kiln but also cup test and drip slag test, allow the best possible understanding of chemothermal brick wear on pilot scale. Prior to testing a complete mineralogical investigation, thermo-chemical calculation via FactSageTM of the slag was carried out. Based on such research results, combined with specific process knowledge RHI Magnesita can recommend appropriate brick lining solutions for non-ferrous metal furnaces.

By B. Wilhelmi, W. H. Somerton

Simultaneous measurement of pore and elastic properties of socks under a wide range of triaxial stress conditions may be made with equipment and methods developed in this paper. Tests were run on three outcrop sandstones at several confining pressures and axial stresses up to approximately 80 percent of failure stress. The greater reduction in porosities and permeabilities occurred in the hydrostatic loading portion of the stress cycle, but substantial reductions in both properties did occur upon application of deviator (triaxial) stress. Triaxial elastic moduli were calculated from strain gauge measurements. Both Young&apos;s moduli and shear moduli were found to increase with increasing confining pressure. Poisson&apos;s ratios increased with axial stress but showed no consistent change with confining pressure. Only very general relations were observed between pore and elastic properties. The lesser decrease in porosity and permeability at higher stress values is related to increase in rigidity of rocks at higher stresses. INTRODUCTION Many investigators have studied the effects of hydrostatic stress on the properties and behavior of rocks. A few have studied the effects of triaxial stress fields on individual physical properties of rocks. To our knowledge no one has measured simultaneously pore and elastic properties of rocks under a wide range of triaxial stress conditions. This is the purpose of this work. Rocks exist in the subsurface under what Jaegerl refers to as "polyaxial" stress conditions (all principal stresses unequal). When two of the three principal stresses are equal, this is referred to as triaxial loading. The triaxial method of loading is most commonly used in modern testing work because experimental difficulties in measuring physical properties of rocks are greatly reduced over polyaxial testing. Although triaxial loading may not reproduce subsurface conditions precisely, subsurface stress conditions are never known precisely anyway. Triaxial testing would seem to be more realistic than testing under hydrostatic loading (all principal stresses equal) for application of results to subsurface problems. The objectives of this work were threefold: (1) to develop methods of measuring simultaneously pore and elastic properties of rocks under triaxial stress conditions, (2) to determine whether changes in these properties are of sufficient magnitude to be considered in subsurface calculations and (3) to attempt to relate changes in pore properties and elastic properties since they will have been measured at the same time under identical loading conditions. REVIEW OF EARLIER WORK PORE PROPERTIES Several investigators have studied the effects of stress on the physical properties of rocks. Fatt and Davis2 showed the reduction of permeability of rock with hydrostatic loading. McLatchie et al.3 and Knutson and Bohor4 related permeability reduction to compessibility of reservoir rock, again under hydrostatic loading. Wble,5 and later Redmond,6 evaluated the effects of applied radial pressure on conductivity, porosity and permeability of sandstones. In this latter work, no axial stress was applied. Dobrynin7 reviewed much of the previous work done . on the effects of overburden pressure on physical properties of rocks. He concluded that changes in physical properties are controlled to a large extent by pore compressibility of the rock. Several sets of curves developed from empirical relations are presented. These curves permit estimation of change of properties with net overburden pressure, knowing the pore compressibility and porosity of the rock. Net overburden pressure is defined as (Pe - 0.85 Pi ) where Pe is the

By Frederick C. Trutt, Jeffery L. Kohler, Joseph Sottile

Twenty-five years ago, the former U.S. Bureau of Mines funded a research project aimed at developing the enabling technology for incipient failure prediction in electric power system components as a means of reducing the injuries and fatalities that sometimes occur when equipment malfunctions. Over the ensuing years, interest in this has waxed and waned, but recently interest has been growing for both civilian and military applications. This paper addresses the level of turn-to-turn insulation deterioration that can be resolved using an on-line monitoring technique. The detection of turn-to-turn defects is especially important because they are believed to represent the beginning stage of most motor winding failures.

By J. A. Putnam, A. D. K. Laird

In laboratory research on the behavior of oil, gas and water in porous materials, no direct method has been devised to measure saturation without disturbing the flow. Indirect methods involving various forms of radiation have been developed for measuring one or two components. The X-ray absorption method for two components has been described previously1-3. The possibility of three component measurement has also been mentioned1. Since two component measurement still requires considerable care to insure accuracy, the fact that three components can be measured satisfactorily is not generally appreciated. The fraction of the energy of an X-ray beam of one wavelength transmitted through a material is given by the transmission factor. in which 1 is the beam&apos;s path length through the fluid. p is the fluid density, and 1,. is its mass absorption coefficient. Eq. 1 implies that all parts of the beam pass through equal amounts of the fluid. Practical applications are, therefore, limited to systems in which the fluid is distributed so that I varies negligibly over the cross-section of the beam. Typical variations of the transmission factor with X-ray tube potential arc shown in Fig. 2 from which experimental points have been omitted for clarity. The X-ray absorption of low pressure gases in a core is practically zero so it cannot he distinguished from that a vacuum by instruments that will differentiate between liquids. The transmission factor of a gas in a core is. therefore, unity. Consequently, the saturation of only one gaseous component can be found. If two fluids completely fill a core, their two saturations add to unity and, therefore, only one value of the transmission factor, T, is needed to determine both of them. When two liquids do not completely fill the core, their saturations do not add to unity and transmission factors at two wavelengths must be measured. At one of these wavelengths, 7 for one liquid must be different from T or the other liquid. The change of T for one liquid us the wavelength is changed between the two values must be different from the corresponding change of T in the other liquid. The two values of fluid saturation will also give that of the gas because the three saturations must add to unity. In Fig. 2 it can be seen that there are many large differences of T between various oil solutions and water solutions at any one potential, and between potentials for any one solution. Consequently, conditions for optimum accuracy of measurement of the saturations of a gas and two liquids can be chosen. Once the operating potentials have been selected, however. it is more convenient to cross plot the data from Fig. 2 on transmission factor-solution concentration coordinates for the chosen potentials, as shown in Fig. 3. Fig. 3 was used to plan the experimental procedure for Core N-38-1. Since the voltage control at 45 kv was good, the slopes of the curves in Fig. 2 at this potential would cause little error. At low potentials, however, the voltage control was not good, so 33 kv was chosen because the small slopes of the curves made voltage control less critical. The lowest strength beam that could be measured reasonably at 33 kv corresponded to a minimum T factor of 0.385. Fig. 3 shows that both 4.80 weight per cent of cadmium chloride in water and 24.0 per cent of iodobenzene in crystal oil had this T value, and, consequently, were indistinguishable to the X-rays at 33 kv. Thus, at 33 kv, the liquid saturation was given by the same curve regardless of the relative amounts of oil and water solutions present. This simple calibration curve from which the gas and liquid saturation can be read, is shown in Fig. 4. Fig. 3 also shows that at 45 kv, T for the aqueous solution is 0.610. and that T for the oil solution is 0.220. These values were transferred to Fig. 4 to give the triangular calibration plot from which the brine and oil saturations can be found, after the gas saturation has been determined at 33 kv.

By O. D. Gaither

This paper is an analytical study of the flow of fluids through small vertical conduits. Small conduits are defined as 11/4-in. nominal diameter tubing size and smaller, and approximately twice this area for annular conduits (i.e., 1- X 21/2-in. annulus and smaller). Experimental data are presented for the 1-X2-in. and 11/4- X 2%-in. annuli, and the I-in. and 11/4-in. tubing, since these represent the small conduit sizes and configurations generally encountered in oilfield applications. Data have been gathered for these conduits for single-phase water, single-phase gas and two-phase water-gas mixtures, with particular emphasis on high gas-liquid ratios. Water rates in excess of 2,000 BID and gas rates in excess of 2.5 MMcf/D, and two-phase flow ratios in between these two, represent the scope of the data gathered. Existing equations have been applied to predict flowing pressures and compared with experimental data. New correlations have been developed. INTRODUCTION The increased economic pressure on the domestic oil industry in the United States has constantly required the use of new techniques and equipment designed to reduce the cost of finding and producing oil and gas. Since tangible items are most readily apparent in economic analysis, the advent of lower-cost well completions was inevitable. One of the methods used to reduce costs which has received widespread attention is the slim-hole completion technique where tubing is used as the well casing and in which small conduits are used for tubing if necessary. Small conduits, defined by Kirkpatrick1 as "11/4-in. diameter nominal tubing and smaller for tubing flow and less than twice the 11/4-in. diameter nominal tubing internal flow area for annulus flow", have also found widespread usage as siphon strings for de-watering gas wells and as "kill" strings in deep high-pressure oil and gas wells. The growing use of small-diameter tubing has resulted in an increased need for development of improved methods to measure or predict flowing bottom-hole pressures since the physical dimensions generally preclude the use of subsurface-recording pressure gauges. Even in the cases where small bombs are available, the relatively high velocities encountered at nominal flow rates make it necessary to use excessive weight bars or special hold-down devices. Attempts to use recognized correlations to accurately predict flowing or gas-lift performance in wells equipped with small conduits have been generally unsuccessful. Insufficient field data were available to allow the development of a correlation on this basis, and an experimental approach was applied in an attempt to obtain a workable relation. The experimental approach used to obtain the data presented in this paper was actually a compromise between a field installation and a laboratory study. A test well 1,000 ft in length was used to obtain flow data on single-phase liquid, single-phase gas and two-phase water-gas flowing mixtures. Liquid rates up to 2,200 B/D and gas rates up to 3 MMcf/D were used in the single-phase flow studies. Two-phase flow rates from 100 to 600 B/D with gas-liquid ratios from 500 to 8,000 cu ft/bbl were recorded. Experimental data were obtained for single- and two-phase flow through 1-in and 11/4-in. nominal tubing, and through the annuli between 1- and 2-in. and 11/4- and 2%-in. nominal tubing strings. Experimental results for the two-phase flow are compared to the Poettmann-Carpenter correlation2 which is widely used as a comparative standard for development of multiphase flow predictions in flowing and gas-lift wells. Correlations developed by Tek,3 Baxendell and Thomas" were also investigated. The experimental data recorded herein fell in between the two flow regimes as defined by Ros," and this correlation also failed to yield satisfactory results. The fact that existing correlations failed to confirm the experimental data led to the need for development of a new correlation. Although a two-phase flow study was the primary objective of this investigation, data were also recorded for single-phase flow of water and gas, and constants were developed relating to pipe roughness and equivalent diameters for annular flow. These single-phase studies assisted materially in the development of certain of the two-phase flow results. Considerable previous work has been published which presented relationship of surface measurements to bottom-hole condition. The works of Buthod and Whiteley,6 Jones,&apos; Poettmannb and the Texas Railroad Commission" are classic examples of the successful use of mathematical relationships which allow acceptable predictions of subsurface pressures, when gas is the flowing fluid. Darcy and others have derived relationships which may be used with minor modifications to predict subsurface flowing conditions in injection and water-supply wells. As previously stated, the application of the single-phase flow relationships

By Davey Bickford, Johan Hawinkel

Blasting and the use of civil explosives are a critical step in the mining process. Good decisions provide significant downstream benefits and create a safe and sustainable working environment, while poor decision making and judgement can have catastrophic consequences on workers safety, critical infrastructure or the security of the general public. An ever-tightening regulatory framework increasingly exposes manufacturers, transport companies and mining companies to the consequences of breaches resulting from erroneous or ill-informed decisions. In this context, new capabilities are required providing all actors in the explosive supply chain with tools to make better informed decisions allowing the individual to own up to his or her decision. Additionally, the traditional risk-control approach in the explosive supply chain up until usage and waste elimination, through administrative control procedures and processes, is becoming increasingly inadequate. In this era of digitalisation and automation, technology will play a pivotal role in ensuring safety and security in storage, transport and usage of civil explosives using the latest advances in electronics, communication technology and information technology. This paper explores the journey through time of technology in the civil explosives market to provide testing, measurement, analysis and control tools. This ultimately leads to better decision-making, ensures full accountability of the decision maker and uses the same technology to review decisions for process improvement, in the settlement of disputes or for the investigation of incidents. Additionally, the paper discusses the application and integration of electronic and digital technology in explosives and initiation systems as engineering controls for blasting associated risks. Finally, this paper reviews two practical cases of technology integration for risk management and improved decision making; the use of integrated GPS technology in initiation systems as an engineering control in the blast evacuation process and the use of RFID technology in explosive tracking from cradle to grave.

By William Gleason

During the past five years, mining operations have had access to press technology for piping and joint fittings that can save owners a significant amount of time when installing or replacing pipes by eliminating the need for welding or threading. Viega, with North American headquarters in Wichita, KA, entered the mining sector in 2009, adding to its already expanding industrial sector. Since then, the company?s global engineering department has paid considerable attention to its industrial division, bringing its expertise in plumbing solutions for residential and commercial buildings to the mining and mineral extraction industry. ?We have a lot of applications in the mining industry.?We have a lot of applications in the mining industry throughout the United States, Canada and Mexico and continue to expand in the mining industry,? Tom Shields, Viega?s director for industrial accounts explained. ?Since we made the decision to increase our presence in the industrial markets, we have been aggressive and more than 240 applications have been approved by our engineering department in Germany.? Getting approval from Viega?s engineering department is no small feat. During a tour of the manufacturing facilities in Ennest and Großheringen, Germany, Mining Engineering, as well as a select few other publications and clients, were shown Viega?s manufacturing process. At the Ennest facility, hundreds of millions of fittings are produced, and each one is inspected mechanically and with a laser at the end of the production line. With four production facilities in Germany and one in the United States, Viega is able to ship to anywhere in the world. The company distributes everything from fittings to stainless steel pipe.

By Oswald J. Heinrich

The great improvement which have been made in late years in the different systems and instruments used to perforate the crust of the earth for purposes of testing and exploring for mineral resources or for other reasons, by means of bore-holes of greater or less diameter and to greater or less depths, are manifold. It may therefore be of interest to make an impartial comparison of them, or of such as are most commonly used. Being well aware of the difficulties which are encountered in such a task, a reasonable allowance most be made in such a comparison. It is a rare instance when even two decidedly different systems or instruments have been used in the same locality, penetrating identically the same strata to the same depth. The diameter of a borehole as well as its greater or less depth must also be considered in regard to its cost per foot, etc. But for practical purposes, for exploration at least, we may assert this rule: Any bore-hole, of whatever diameter, which allows the means of examining the strata most carefully and completely, will be sufficient for this purpose, but that one which will do it most economically and in the least space of time, must be considered the best for it. It will, therefore, partially depend upon circumstances, what system, in spite of other superiorities, may be the best in each case, and the following remarks may aid in deciding this question. To make the attempt here to review all that has been published upon the different systems and means of boring would be out of place. Reference can be had to the able publications treating upon this subject. A difference in this respect exists in regard to the use of the hollow rods in connection with the diamond drill, used for that purpose. The great future, which appears to be evident for this instrument, will be warrant enough for any one, who has had the opportunity to test it, to give his experience to the public. Only in this way can we bring this system to such perfection, as it seems to deserve and

The general standard of engineering in South Africa will, it is believed, reach new heights after the establishment of the S.A. Council for Professional Engineers (SACPE) in February, 1969. The Council is being created to establish standards for professional engineers in this country and ensure that the quality of engineering is maintained at a high level. In terms of the Act of Parliament under which the new Council will operate, all consulting engineers will have to be registered if they wish to remain in private practice. While engineers who are not in private practice cannot be compelled to register, it will be in their interests to do so, according to a statement issued by Mr M. R. Gericke, chairman of a Shadow Council which is at present preparing for registration and drafting the requirements for registration. Registration is seen as an important move towards maintaining the quality of engineering in South Africa. Engineers will be encouraged to strive for professional status by gaining the necessary qualifications and the varied range of experience required by the Council before registration. All work done by registered professional engineers will have to conform to certain minimum standards. A spokesman for the Council has urged all engineers to ensure that they apply for registration when the Act comes into force in February. The Council is also anxious to gain the co-operation of employers in ensuring that the holders of professional engineering posts will be registered. Full information regarding registration will be sent to engineers throughout South Africa early this year, and announcements will appear in the press.

By L. K. Nemeth, H. T. Kennedy

The investigation presented in this paper was performd to develop a relationship between the dewpoint pressure of a hydrocarbon reservoir fluid and its composition, temperature and characteristics of the heptanes-plus fraction. This is part of an over-all program to develop correlations for the essential properties of reservoir fluids with the composition, temperature and pressure. In all, 579 dewpoint pressures, determined experimentally on 480 different condensate systems along with their compositions and temperatures, were obtained from the literature and from previously unpublished sources. Compositions were expressed in terms of mol fractions of methane through heptanes-plus, nitrogen, carbon dioxide and hydrogen sulfide, and the molecular weight and specific gravity of the heptanes-plus fraction. Distribution of the samples assured a good representation of most of the major oil-producing areas in the world. A multiple regression analysis program written for the IBhl 7094 digital computer was used to compare numerous equations and to calculate their coefficients. The final equation containing 11 coefficients resulted in an average absolute deviation of 7.4 percent for all the samples. Segregation of data on the basis of one or more variables did not materially improve the results. The correlation developed is useful in predicting the dewpoint pressure of condensate reservoir fluids from variables normally measured in the laboratory. INTRODUCTION In any discussion of the dewpoint of hydrocarbon mixtures, it should be noted that there are two kinds of dewpoints which must be distinguished. The first type, or normal dewpoint, usually occurs at low pressures as dry gas is compressed to the point where liquid first forms. The second type, sometimes called the retrograde dewpoint, occurs when a gas mixture containing heavy hydrocarbons in solution is depressured until a liquid is formed. The first type, as applied to condensate mixtures, would normally be below atmospheric pressure and would be of no interest in reservoir performance. The second type is of great significance in interpreting reservoir behavior and is the property referred to throughout this paper. Laboratory measurement of dewpoints is laborious, expensive and subject to many errors, and it is desirable to find a reasonably accurate method to predict dewpoint pressures from the composition and other readily available properties normally measured on the fluids. A possible method of calculating dewpoint pressures would be to employ a set of equilibrium ratios (K-values). 1 However, the K-values themselves depend on composition as well as temperature and pressure; presently their use adds nothing to the accuracy of predicting dewpoints. If future correlations provide a significantly better method of estimating K-values for heavy hydrocarbons, they may be of greater use. REVIEW OF LITERATURE In 1944, Olds, Sage and Lacey 2 studied the behavior of fluids from the Paloma field. Properties of seven mixtures were studied at temperatures ranging from 100 to 250 F and at pressures up to 5,000 psia. From the information obtained, the influence of composition and temperature upon the dewpoint was determined. It was found that removal of the intermediate molecular weight components from the mixture resulted in considerable increases in the dewpoint pressures. Results indicated that the effect of changes in temperature was relatively minor when compared with the effect of modifying the mixture by removing the intermediate components. Thus, removal of propane and butanes resulted in an increase in dewpoint pressure more than 10 times greater than a change in temperature from 100 to 250 F. The authors stated that althouah

By Alper Turan

The use of aggregate pier foundation systems has become widespread as the engineering practice moves towards cost-effective ground improvement solutions that provide accelerated construction schedules. Increased bearing capacity, effective settlement control and potential for liquefaction mitigation are commonly acknowledged benefits of aggregate piers. This paper studies the mechanisms by which aggregate piers interact with each other and with the surrounding ground when excited by seismic loads. A particular emphasis was placed on the response of a raft foundation supported on a site improved using aggregate piers. Three-dimensional nonlinear finite element analyses were conducted using commercial software package, ABAQUS. Non-linear soil behaviour is modelled using a three-dimensional total stress-based bounding surface plasticity model, which is able to simulate stiffness degradation and damping increase in the soil. The soil stratigraphy considered in this study was a 30 m deep soil deposit that comprised a very stiff base layer and a shallow soft surficial clay layer. Ricker Wavelet time histories with different frequency contents are used as the excitation force in the analyses. Various area replacement ratios (ARR) for aggregate piers are studied for a square plan layout. The results presented in this study are considered to be of interest to researchers and designers in evaluating the seismic ground response of the sites improved using aggregate piers.

By T. A. Larssen

The efficiency in production of manganese ferroalloys is dependent on the gaseous reduction of the higher manganese oxides in the ores used as raw materials. The materials, descending in the furnace, will meet the furnace gas that contains significant amounts of CO(g) and reduce in subsequent steps, the last step being reduction of Mn3O4 to MnO. This step may to varying extent occur at temperatures exceeding 800 °C, i.e. in the active region of the Boudouard reaction. The gas reduction of Assmang and Comilog manganese ores were investigated in CO-CO2-atmosphere at temperatures up to 1000 °C. It was seen that decreasing ore size correlates to a lower reduction temperature and increasing reduction rate. Similar effect was observed with increasing CO-content in the gas atmosphere. Further, it was found that Comilog ore obtained a complete prereduction at 600 °C, whereas reduction of Assmang ore was not complete at 800 °C for the majority of the experiments.

By I. O. Otunniyi

The natural hydrophobic response flotation method for beneficiation of printed circuit board comminution fines (PCB CF) still requires many studies to further basic understanding of the process and the flotation traits that the PCB CF presents. Varying particle size distribution (PSD) and water recovery under the scheme show that higher mass pull, obtained at the finer PSD, gave lower water recovery but higher value loss. The reverse also holds: the least mass pull at the coarsest PSD used, -106 + 75 µm, gave the highest water recovery per unit mass pull with the highest reverse recovery. This is unlike what obtains in primary resources processing, where higher water recovery is often with increased fines entrainment. The reverse recovery loss here is, therefore, more due to entrapment with the heavy mass pull characteristic of the method than to the entrainment of value with water. Other peculiarities of the system observed are discussed, with the goal of improving the performance of the process, and broadening the general knowledge of flotation systems.