Search Documents

By R. L. Slobod, C. Gatlin

This .study defines the basic mechanism of the mis-cible displacerrzent of oil and writer from porous Medici by various water-driven alcohol .slugs. Three distinct alcohol slug processes were .studied. Considerable data concerning the quanity of alcohol required for oil recovery were also obtained. All data were obtained in a 1-in. diameter, 100-ft long, unconsolidated core. The porosity of this system was 35 per cent. and the permeability was approxitrlately 4 darcies. Total core pore volume wax 5,716 cc. All displacements were conducted at a constant injection rate of 5 to 6 cc//min, which corresponds to a frontal advance of 5 ro 6 ft/hr. The first portion of this paper is concerned with 111 use of one alcohol—isopropyl—a\. the slug material. Isopropyl alcohol (IPA) is completely miscible with both oil rind water; however, miscibility of the threc-component systems, oil-water-IPA, requires a relutively. high concentration of IPA. Hence, the displocement is not of the misoible type unless the IPA concentration is maintained above some critical value. A slug of IPA equal to only 13.5 per cent of the pore volume was jound to be sufficient to obtain complete recover?, of residua1 naphtha. In later studies two distinct process variations were developed. The firsr of these utilized methyl alcohol (MA) and IPA as slug materials. It was shown that methyl alcohol may he substituted for IPA at the front and rear of the slug with no loss of oil recovery. A .slug of 4 per cent MA-4 per cent IPA-4 per cent MA was sufficient for complere oil recovery. Because MA is considerably cheaper than IPA, this represents an important step toward economic application. A .second process variation used normal butyl alcohol (nBA) and MA as the composite slug, the nBA segnzent being injected first. This technique requires the smallest total slug size (approximately 10 per cent) of all processes studied. The high cost of nBA, however, precludes commercial application. It is possible that this basic process, subject to changes of alcohol type, may lead to a commrercicil process. INTRODUCTION Within the last 10 years, considerable study has been devoted to the general mechanics of miscible phase dis- placements in porous media. These studies have. in general, dealt with two-component displacernent. All reported field trials to date have been modified gas drives of one type or another. These utilize either lean gas at high pressure, rich gas at lower pressure or an LPG slug. The irreducible water content of the reservoir remains immobile during these processes. Although these techniques hold great promise. certain drawbacks do exist. Poor areal sweep efficiency, inherent in any displacement having a highly unfavorable mobility ratio, is one disadvantage. Furthermore, the miscibility of all processes which use gas is dependent on pressure. These pressure limitations may prohibit application to shallow reservoirs. There are also many areas where large quantities of LPG and natural gas are not readily available. These factors emphasize the need for improved techniques. The alcohol slug process is also a miscible-phase displacement process. It differs from the previously mentioned two-component techniques, however, in that both the reservoir oil and water are displaced by the slug. This behavior is a consequence of the miscibility of certain oil-water-alcohol systems. In the simplest case, a relatively small volume (slug) of an alcohol (such as isopropyl) is injected into the system. Water is then used to drive the slug through the medium. Thus. three components—-alcohol. oil and connate water-—exist at the front side of the slug. Miscibility is obtained at some alcohol concentration, this being dependent on the solubility of the particular system. Miscibility is maintained within the slug until the alcohol concentration falls below that value required to maintain miscibility. When miscibility is lost, the process reverts to a water flood. Certain inherent benefits of this technique are apparent. High pressures are not necessary to obtain miscibility in these liquid systems. Furthermore, water is a more desirable driving agent than gas because of the improved mobility ratio and the attendant improvement in areal sweep efficiency. The main disadvantage is, of course, the relatively high cost of alcohols. The use of an alcohol slug to recover reservoir oil is not a new idea." ' However, this process has received only limited study, presumably due to the lack of industrial interest caused by the seemingly prohibitive cost of alcohols. The main purpose of this study was to investigate the mechanism of the displacement of oil and water by various alcohol slugs and to develop process modifications aimed toward possible commercial application.

By Charles R. Stewart, William W. Owens

Reservoir performance predictions based on laboratory core test data assume that fluid flow is laminar for the laboratory test. A study has been made to determine the validity of this assumption for laboratory tests on various types of porosity found in producing limestone formation. Data are presented which show that turbulence and slippage can occur during laboratory tests on hetero-geneous-type porosity limestones, thus causing serious errors in measured single-phase permeabilities and two-phase relative permeability characteristics. In single-phase flow tests it is possible to eliminate turbulence and correct for slippage or to eliminate both factors by controlling test conditions. It is not always possible to control test conditions and thereby eliminate turbulence and slippage in two-phase .flow tests. A correction method is presented which can be used to calculate the true two-phase laminar flow relative permeability characteristic even though furbulence and slippage exist. .INTRODUCTION It is customary to make use of Darcy's law and modifications of this law, together with laboratory data on formation core samples to predict the performance of producing reservoirs. Such predictions are based on an assumption that fluid flow is in the laminar or streamline region for the laboratory test. It was the purpose of this inves- tigation to determine the extent to which turbulent flow may occur in laboratory fluid flow tests on hetero-geneous porosity limestones. Considering that turbulent flow conditions might exist in some laboratory fluid flow tests, additional emphasis was placed on the development of a method to correct for turbulence when laminar flow conditions could not be attained. FLUID FLOW CONCEPTS FOR POROUS MEDIA The Influence of Pore Geometry on Fluid Flow One of the more important factors influencing fluid flow in porous media is the geometry of the pore space which includes such characteristics of the pores as size, shape, distribution, roughness, uniformity, etc. In general, oil- and gas-producing formations can be divided into two broad types on the basis of pore geometry. One has been called sandstone-type porosity media, which is characterized by a small range in pore size, uniformity in shape of the pores, smooth pore surfaces and a regular and uniform distribution of pores. The other type has been called heterogeneous porosity media and is usually limited to the dolomites and limestones. This type is characterized by a wide variation in the size, shape, and distribution of the pores and rough, irregular pore surfaces. It is therefore apparent that conditions are much more favorable for turbulent flow* in heterogeneous-type porosity media than in sandstone-type porosity media. Interrelationship Between Turbulence and Gas Slippage In studying the problem of turbulent flow in laboratory tests on porous media, it is necessary to be aware of the interrelationship between slippage and turbulence for gas flow. As a result of slippage or the Klinken-berg effecta, apparent perrneabilities to gas are greater than the true value because there is no stationary layer of gas in contact with the walls of the flow channels. Gas slippage decreases as the mean free path of the gas molecules decreases. Since the mean free path of any gas decreases with increasing density, increases in static pressure result in lower apparent gas permeabilities. However, a reduction in gas permeability can also be due to turbulence. Therefore, in studying only turbulent flow in porous media, it is necessary to hold gas density, and slippage, constant or to reduce slippage to a negligible value by operating at high static pressures. Presentation of Laminar and Turbulent Flow Data A graphical relationship between permeability and a pseudo-Reynolds number, N,, will be used to show the two types of fluid flow, i.e., laminar and turbulent. The usual graphical method for such a description has been the use of friction factor-Reynolds number charts4. On such a logarithmic diagram, the laminar region appears as a straight line having a slope of 45 degrees. As the friction factor decreases and the Reynolds number increases, the turbulent region is reached and appears as a deviation from the 45-degree slope line. However, in petroleum engineering literature resistance of por-

By Sebastiaan Peelman

NdFeB permanent magnets are the best available magnets used in many technology applications. However, at their end-of-life (EoL) most of magnets and the contained REEs are lost during the recycling of the bulk metals. The REEs are classified as the most critical raw materials in the European Union, and recycling of REEs from EoL products will reduce their criticality and contribute to the sustainability of REE. Various technological routes have been reported, but most of the methods are effective for highly concentrated magnets or magnet scrap, which is greatly dependent on expensive pre-dismantling processes. This paper presents various innovative metallurgical solutions to the effective REE recovery from current industrial practice for WEEE recycling, including the ferrous scrap from WEEE shredder products and shredder residues from computer hard disk drives. Both hydrometallurgical and combined hydro- and pyrometallurgical REE recovery routes are developed after demagnetization and physical upgrading.

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publications Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. LAYOUT AND STYLE Orthodox sequence Title and author's name, with author's degrees, titles, position. Synopsis, including a brief statement of conclusions. Index, only if paper is long and involved. Introduction. Development of the main substance. Conclusions, in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors &, Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler. H. W. & F. G. The King's English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory \matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. If there is any problem in producing formulae accurately by typewriter they should be inserted by handwriting in ink in the copy forwarded by authors. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol %is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systeme International d'Unites (S.L) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramms metre per second per second (kg m/s2). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, n, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standard symbols as laid down in British Standard 1219C should be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and there. fore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .' . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publication of technical notes taking up to three pages (maximum 3 000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute as a body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there IS full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organizations as well as to the Institute.

By G. R. Countryman, G. H. Thomas, I. Fatt

Procedures are described for scaling up turbulent friction pressure drops of inelastic fluids and laminar friction pressure drops of inelastic/elastic fluids in circular ducts. The laminar scale-up calculation method does not require the use of arbitrarily defined flow models, and can be performed directly from laminar capillary viscometry data, or by means of a numerical solution of the integral equation for Poiseuille flow, inputing true shear rate-shearing stress data from other simple shearing experiments. e.g. Couette and plane Poiseuille flows. The turbulent scale up procedure, based on the Dodge-Metzner correlation for inelastic fluids, requires evaluating the characteristic rheological parameters at the existing wall stress under laminar flow conditions. Since the wall stress is the quantity sought in a pipe flow scale-up problem, a trial-and-err or solution is indicated, and therefore a calculation method has been developed and programmed for a medium-size magnetic-drum-memory digital computer. Laminar flow data from other somces may also be adapted to this turbulent scale-upmetbod for inelastic fluids. Comparisons between predicted and experimentally observed friction losses for generalized Reynolds numbers ranging from 3 — 32.000 indicate an error band width of less than 10 per cent in circular tubes ranging in size from 0.5 to 1.89 in. in diameter. INTRODUCTION Considerable effort has been devoted to the problem of establishing an accurate procedure for predicting the laminar and turbulent flow behavior of non-Newtonian materials in pipes from data obtained with small scale laboratory or pilot plant equipment, as evidenced by the variety of reviews on the subject.1-3 Although there does not appear to be a universally accepted scale-up method for laminar flow, the various methods currently employed can be divided into two principal categories depending upon whether a functional relationship between shear rate and shearing stress is assumed, or whether a generalized correlation is adopted. The methods of Hedstrom4 and of Weltmann are typical of the first category, while the generalized correlation of Metzner and Reed6 illustrates the second category. Under appropriate conditions either approach yields a reasonably satisfactory description of laminar flow behavior. In contrast, the prediction of non-Newtonian transitional and turbulent friction losses is much more complex. For example, certain types of materials have been observed to sustain laminar flow at much higher flow rates than Newtonian liquids. When turbulence does develop, the level of agitation is damped to such an extent that the friction factor is lower than that of the original low viscosity Newtonian medium. Extremely broad transition regions and "diameter effects" have also been noted in the turbulent flow of certain chemically complex materials.' Aside from the latter complications, which are attributed in part to viscoelasticity, the existence of a variety of scale-up procedures for predicting transitional and turbulent friction losses is due principally to the chioce of viscosity parameter used in the definition of the Reynolds number. In contrast, Dodge and Metzner have demonstrated that the friction factorReynolds number relationship for inelastic fluids can be satisfactorily generalized provided the fluid property parameters are evaluated at the existing wall shearing stress.* However, the quantity usually sought in a pipe flow scale-up problem is the wall stress, and hence a trial-and-error procedure is required when dealing with non-power law materials. In this report we discuss two calculation methods: (1) for determining the wall stress, and hence the friction pressure drop, for inelastic fluids under conditions of turbulent flow by means of an iterative procedure, and (2) for predicting laminar friction pressure drops without recourse to arbitrarily defined flow models.

By K. A. Slagle, D. K. Smith

weight obtained. Additives used in conjunction with salt in these slurries have included silica flour, calcium ligno-sulfonate and cellulose retarders, granular lost-circulation materials, bentonite and selected low-water-loss additives that are not significantly deteriorated by the presence of the chloride ion. In some other areas of South Texas, the salt-saturated slurries have been used quite extensively for improvement of the flow properties of slurries and attainment of better circulation characteristics at lower displacement rates. Concurrently with this property, the protection of shales and shaly sands is also realized, as well as useful retardation of the slurry. Resultant superior cementing jobs have been indicated by both communication tests and acoustic logs for bonding to pipe and formation.' In one section of Louisiana, a major oil company has been using salt-saturated API Class A cement with calcium lignosulfonate retarder for cementing through the Miocene at 9,000 to 10,000 ft. This is another of the situations where interbedding of sands and shales exists, creating difficulty in maintaining formation competency when a fresh-water slurry contacts the clay minerals of the formation. Further work has also been done in the shaly Miocene formation at 13,000 to 15,000 ft where fairly close water or gas contacts are encountered. Indications thus far are that better segregation of these various fluids is obtained by use of the saturated salt slurries because of their improved formation bonding characteristics. In addition to the properties of salt in this situation, attainment of turbulent flow at minimum displacement rates has also been accomplished by use of an additive to help provide exceptional dispersion and viscosity reduction of the slurry. Another oil company was encountering considerable expense in completing wells in Southwestern Louisiana due to extensive block squeeze requirements for effective separation of zones. A very effective mud program was being used to minimize washout in the shale sections and, apparently, a nearly gauge-size hole was being obtained. However, primary cementing results with fresh-water slurries were generally poor. On a few occasions when slurry was actually circulated to the surface, large pieces of shale formation were brought out of the hole with the slurry, indicating a severely water-sensitive, sloughing formation. Inhibition of shale heaving was being accomvlished in the drilling program, and immediately indone ipon circulation of the fresh-water slurry even though it contained a low-fluid-loss additive to reduce filtrate damage in the sands. The subsequent change to salt-saturated slurry yielded 11 successful primary cement jobs out of 12, compared to the previous success ratio of practically zero. Since these were deep, high-temperature wells in the range of 13,000 ft with high-pressure zones necessitating 17.5-lb/gal fluid densities, the slurry used was API Class E cement, silica flour, weight material, retarder, salt saturation (which also reduced the amount of weight material) and maintenance of low fluid loss by use of a salt-compatible additive. Other salt slurries have been used to a limited extent in this same general area for similar problems at depths ranging from 5,000 to 17,000 ft. In the shallower wells, the cement has usually been API Class A where the salt functions as a retarder, and in the deeper wells API Class E cement is used with the additional salt advantage being its increased slurry weight and inability to dissolve salt stringers. A considerable number of squeeze jobs have also been done on older wells using the salt-saturated slurries with very good results. MID-CONTINENT In North Texas, salt-water slurries have been used for cementing the Woodbine sand, Strawn sand, KMA sand and Pettit lime. Shales surrounding these formations have created the same difficulty in obtaining separation of producing zones that has been the problem in other areas. Depths in this area range from 3,400 ft for the Strawn to 7,400 ft for the Woodbine, and concentration of salt has varied accordingly. In the deeper wells, where retardation is desired, saturated salt-water cement is used; for the shallower wells, in order to provide shorter waiting-on-cement times, the amount of salt has been 18 per cent by weight of the mixing water. Results have been excellent with no reported failures on any of the salt cement jobs; where acoustic bond logs have indicated indifferent bonds previously, they are indicating very good bonding for the salt slurries. In Oklahoma various shales of Pennsylvanian age exhibit a high degree of sloughing in the presence of fresh water, causing severe washouts above and below sand formations which it is desired to isolate. This situation exists to some degree in practically all parts of Oklahoma and includes formations of other ages such as the Wood-ford shale. For the past few years, salt-saturated cements and displacement rates as high as practical have been used as a remedy for this problem, with very good results. The Layton and Bartlesville formations are two examples of shaly sands where saturated slurries have been helpful. In one area where five wells were drilled through this type of problem shale without obtaining a satisfactory primary cement job, a change was made to salt-saturated cement preceded by a suitable chemical wash for the drilling mud involved. Acoustic bond logging indicated excellent bonding, and final completion bore out this result by being trouble-free. This type of slurry has also been used extensively on squeeze jobs where shales have been heaving around the producing formations. Predominantly, the basic slurry has been either API Class A cement or a pozzolan cement—although, as deeper wells are being drilled, the use of salt in Class E cement is also increasing. Salt cement in West Texas has been used primarily to help prevent channeling through the shales around the Delaware sand, Queens dolomite and Hope lime. Many of the shaly and dirty sands of this area are sensitive to the filtrate from a fresh-water cement. Salt at 16 to 18 per cent by weight of mixing water has been added to centent, and has been effective in controlling formation damage and communication between zones in these formations. Use of these lower salt concentrations is dictated in this area by the relatively low formation temperatures where retardation of the slurry would create unduly long waiting-on-cement times. Also, quite a bit of cementing has been done in this area using salt concentrations in the accelerating range— that is, 2 to 5 per cent by weight of water. Specifically, these concentrations have been used in coiljunction with high percentages of gel to overcome the retarding effect of the calcium lignosulfonate dispersant, although there are probably several shales where these concentrations could provide some degree of formation stability. On several occasions, the salt has also been used to lower the critical velocity or rate for turbulence with the slurry, particularly in the pozzolan cements. On wells in the Hope lime, it has usually been necessary to squeeze the shale above and below the lime to get a water-free completion. Use of salt-saturated slurries has largely eliminated this

By J. B. Campbell, V. V. Valleroy, B. T. Willman, L. W. Powers

A steam drive of heavy oil was field tested in a shallow, low oil-saturation formation near Deerfield, Mo. The pilot was conducted in the Warner formation, a sandstone containing an 18' API oil having 1,000-cp viscosity at the 60F origind reservoir temperature. The formation war at a depth of 160 ft. Steam was injected into nine input wells arranged in an array of inverted five-spot patterns. In the completely confined center pattern, 14 temperature observation wells were installed to obtain thermal data and observe test progress. Late in the test, slugs of ammonia were injected to trace the flow paths of injected fluids. From the test area about 7,000 bbl of oil were produced. Data were obtained on areal and vertical temperature distribution, steam front advance, reservoir fluid movement and terminal saturations. This field test of a steam drive (I) demonstrated the feasibility of the method, (2) confirmed that the low residual oil saturations observed in the laboratory are obtained in the steam-swept region in the field and (3) provided recovery and conformance data for one set of field conditions. INTRODUCTION The Deerfield steam drive pilot test was conducted in a shallow sandstone containing 1,000-cp oil. The venture was undertaken cooperatively by the research and production departments of Carter Oil Co., which organizations have since been consolidated into Esso Production Research Co. and Humble Oil & Refining Co.. respectively. The production department was interested in steam injection at Deerfield because it appeared to be the most promising method of commercially producing this heavy oil deposit. The research department was interested in applying the new recovery method and in evaluating its performance in the field. At the time the test was begun, the initial oil saturation was not well known. Subsequent air coring and early pilot results confirmed that there was too little oil in place for profitable commercial exploitation by steam. Pilot termination at that time, however, would have been premature for evaluating field performance of the process, and the tert was continued to obtain additional data on steam injection as a recovery method. The test was located in Vernon County, Mo., about 10 miles north of the town of Deerfield and only a few miles from the Kansas border. The pilot site was selected as typical of the area. The location represented neither the highest nor the lowest oil saturation region in the acreage under lease in 1954. The steam drive was conducted in the Warner sandstone of Lower Pennsylvanian age. At the test site the top of the Warner occurs at about 160 ft subsurface and the formation is a fine- to medium-grained micaceous sandstone that dips gently to the northwest at the rate of 12 to 15 ft/ mile. A cross-section and permeability profile of the test location are shown in Fig. 1. At the pilot location the average total thickness of the Warner formation is about 43 ft, but the effective thickness for steam drive is 26 ft. Two distinct types of hydrocarbon saturation are apparent. The lower portion of the total sand, averaging about 17 ft thick, contains a very heavy asphaltic material that will not flow under the influence of a steam drive. This bottom interval, referred to as a dead oil residue, was not considered as part of the net sand undergoing steam exploitation. The initial formation and fluid properties of the upper 26 ft in the test area are summarized in Table 1, and variation of oil viscosity with temperature is shown in Fig. 2. Imbibition tests on preserved core samples taken at the end of the pilot test showed that the Warner sandstone was then neutral or slightly water-wet. Initially, the reservoir may have been strongly water-wet as indicated by low relative permeability to water during both water injection testing and early steam injection. PRIOR HISTORY Initial production tests of wells at the pilot site produced water with only a faint show of oil. No gas was produced except at Well 7-W in the pilot area and at another well about 1/3 mile northeast of the pilot. Prior to the start of the steam drive, a two-well water injection test and a two-well air injection test were conducted. No oil was produced by either. Water was pumped into Well I-W in the northeast corner of the pilot area with simultaneous production from Well 1 (Fig. 3). The air-injection tat was run at input Well 9-W and its offset, Well 2, in the southwest corner. Air and water injectivities were about the same when corrected for viscosity and pressure differences.

By H. S. Price, R. L. Reed, J. E. Warren

The behavior of the reverse-combustion process in a linear adiabatic system is theoretically investigated by means of an idealized physical model. T his model is described by a pair of non-linear equations involving heat and mass transfer which are coupled by a concentration-dependent reaction-rate function of the Ar-rhenius type. The differential equations governing the quasi steady-state temperature and concentration distributions are approximately solved by using either physical or mathematical simplifications. It is shown that the reverse -combustion process can be mechanistically described by simple physical models whose behavior equations can be solved formally. It is further demonstrated that the derived reverse-combustion equations can be solved numerically within the error limits for the experimental data. The theoretically predicted peak temperature-flux-velocity relationship exhibits reasonable agreement with experimental data obtained from Athabasca tar sand. The principal contribution of this work lies in its usefulness as a starting point for developing a more comprehensive theory. A description of the vaporization-coking process must be obtained; then, the theory must be extended to three dimensions to include geometrical effects and heat losses. INTRODUCTION In another paper,'" he physical processes visualized as occurring during reverse combustion have been described. In this paper, the extent to which an elementary theory can account for experimental observations is determined. Theoretical results that can be used to estimate some of the behavior characteristics of importance to this process are also presented. Since it is not possible to include all the features of the combustion mechanism of which we are currently aware, the mathematical formulation refers to the highly idealized system developed herein. This simplified physical model is based on the simultaneous transfer of mass and heat accompanied by a chemical reaction: it is described mathematically by a pair of coupled, nonlinear differential equations. Similar sets of equations have been studied extensively in the field of flame propagation; an excellent review of these investigations has been published by Evans.1 FORMULATION OF THE PROBLEM It will be recalled that the experiments are performed with a thin-walled cylindrical tube that is uniformly packed with sand and oil. The system is maintained substantially adiabatic by means of heat supplied externally in such a way that the radial temperature gradient in any plane normal to the axis of the tube approaches zero. Initially, the tube is at ambient temperature, except at one end where it is rapidly heated to a predetermined temperature. When the prescribed temperature is achieved, air is caused to flow into the cold end of the tube. As the oxygen in the air stream contacts the hot oil, a localized exothermic reaction takes place. The generated heat is conducted and convected away from the reaction zone so that definite temperature and concentration profiles are rapidly established and move uniformly in a direction opposite to that of the air flow (Fig. 1). As a consequence of this mode of oxidation, all of the oxygen in the air is consumed; then, the remaining nitrogen and the gaseous combustion products sweep out all vaporized hydrocarbons and leave an immobile hydrocarbon-coke on the sand.

By A. L. Hinde, A. A. Bradley, P. J. Lloyd

The results of slow crushing tests in a stiff testing machine for both small and large step reductions of particle size are given. The energy consumption required to produce a given weight of minus 74 um material was determined when both single-crystal quartz and Witwatersrand reef were crushed. For comparison the two materials tested were also comminuted in a ball mill under optimum conditions. There are indications that slow crushing under stiff conditions is the most efficient method of breakage that can be devised. The comparison with ball milling results thus yields a value for the efficiency of ball milling of approximately 80 per cent. These results confirm that the best current estimates of milling efficiency, which are based on the free boundary surface energy of the material being milled, are probably too low by at least one order of magnitude.

By T. W. Beck

The National Institute for Occupational Safety and Health (NIOSH) conducratory and field tests to evaluate the effectiveness of dust collector bags for reducing dust liberation and operator exposure from a roof bolter’s dust collection system. The laboratory tests evaluated the bag’s effectiveness to contain dust and the effect on canister filter loading in both a bag and bagless condition. The dust emissions from the collector’s exhaust were also measured in each condition during laboratory testing and show that nearly 100% of the test dust fed into the collector was captured by the dust bags. Loading and pressure drop on the dust collector’s canister filter is greatly decreased when using the bags, enabling longer periods of drilling without filter removal/cleaning. The field results showed that, even though dust standards were met, respirable dust in exhausted emissions was reduced around the bolter. Laboratory and field results show that benefits from use of the bags are realized in all areas of operator exposure.

By A. J. S. Benade, A. J. A. Heyns, N. B. Strydom

The maximum oxygen intakes of samples of about 30 Bantu, weighing less than 50 kg from different tribal groups (Zulu, Xhosa, Sotho and Shangaan) were measured on a treadmill. The mean maximum oxygen intake of the 164 men was 2,12 litresjmin and only 18 men (11 per cent of the sample) had maximum oxygen intakes of 2,5 litres/min or above (the minimum requirement for such tasks as shovelling rocks and tramming it). The samples of the different tribes differ in age, but when the age effect is taken into account then there were no significant differences between tribes in maximum oxygen intakes. An incidental finding was that both age and body weight correlated significantly with the maximum oxygen intakes of these underweight subjects. Not one of the subjects who weighed less than 45 kg or who was older than 40 years had maximum oxygen intakes high enough to permit their being able to do strenuous work underground. It is clear therefore that Bantu who weigh less than 45 kg or are older than 40 years should not be employed on such strenuous tasks as shovelling rock and tramming it.

By Lon D. Santis

This paper presents data and theorem to calculate the risk of experiencing undesirable lightning related events while blasting or while engaged in other lightning sensitive activities. The paper provides an overview of lightning hazards in blasting operations and a brief history of lightning related blasting accidents. Lightning continues to be the primary cause of premature initiations of explosives in mining, on average, over two such incidents are reported to the Mine Safety and Health Administration (MSHA) each year. The energy contained in lightning discharges and how this energy sets off explosives in mining is presented. Three categories of lightning warning methods: public media, lightning detectors, and atmospheric electrostatic field measurement are discussed. The remainder of the paper presents recently acquired data on the spatial characteristics of lightning development. This data is used to estimate the risk assumed by blasters under certain conditions. Risk estimations are made for electric and nonelectric blasting if persons are evacuated when cloud-to-ground (c-g) lightning approaches within a certain distance. For example, about 0.6% of all c-g lightning strikes have no other c-g lightning strikes within 25 miles in the previous 30 minutes. The paper shows that a typical blaster using nonelectric initiation in a high lightning density area with a 100% accurate lightning detector set to alarm at 25 miles would have a lightning caused unplanned detonation every 14,000 years

By Jafar Safarian

Bauxite is the main raw material used for the production of alumina (Al2O3) through the well-known commercial Bayer process. This process has significant challenges such as limitation in using low-grade bauxites as they contain significant amounts of impurities such as Fe, Si, Ti. The Bayer process residue, which is known as red mud, is also a global environmental challenge due to huge amount of this low value residue production. An alternative sustainable process with high potential to solve these problems and produce valuable and consumable by-products is a pyrometallurgical-hydrometallurgical process in which the low-grade bauxite ore is treated through a smelting-reduction process, yielding iron alloys and a calcium-aluminate slag. Alumina is then produced from the slag by hydrometallurgical treatment. In the present work, the reduction of pellets produced from different bauxite ores by hydrogen is studied and it is shown that complete iron oxides reduction is possible. Further smelting and smelting-aluminothermic reduction of the reduced pellets show that iron and silicon ferroalloys can be produced, in addition to a proper slag for alumina extraction.

By C. P. Lawhon, J. P. Simpson, W. M. Evans

Data obtained under controlled test conditions using a microbit drilling machine showed that oil emulsified in water muds may either increase or decrease the drilling rate, depending upon drilling conditions. A low-viscosity oil such as diesel fuel can give drilling rates in limestone almost equal to that of water. Data obtained for water emulsified in oil muds showed little decrease in the drilling rate in water-saturated cores as the water percentage of the mud was increased above the 5- to 10-percent range. Changes in drilling rate were found to be dependent upon the oil or water concentration of the mud and upon the type of formation drilled. Changes in static filtration on paper (API filtrate) did not correlate with filtration while the mud was circulated across rock. INTRODUCTION Oil additions to water muds have been reported to increase drilling rates, provide hole stability and improve filtration control. Eckel' showed that water-base emulsion muds used in the West Texas area increased drilling rate with increasing oil concentration up to 15 percent oil by volume, but drilling rate decreased at a concentration of 20 percent by volume. Based on laboratory tests using water muds to drill shale, Cunningham and Goins' reported that drilling rates increased and tendency for the bit to ballup decreased with the addition of oil. Percentage increase in drilling rate varied with the particular formation. They showed oil additions to improve drilling rates ap proximately 75 percent in Vicksburg shale and as much as 150 percent in Miocene shale. Each investigation showed an optimum oil content for the particular formation. Most data that indicated improved filtration control due to oil additions were based on static API Eltrates through paper rather than dynamic filtration through permeable rocks. Some types of dynamic test give a better representation of filtration down-hole while drilling and might be more likely to show some correlation with drilling rate. Static filtration would be important, of course, in relation to hole stability and formation damage. This laboratory's drilling tests, conducted on water-raturated Berea sandstone, indicated that improvements in drilling rate were not evident with increasing oil concentration in water-base muds. Investigation also showed similarity between oil-emulsion (water-in-oil) muds and water-emulsion (oil-in-water) muds while drilling these formations. In Lueders limestone high concentration of water-in-oil muds and high concentration of oil-in-water muds provided the same relative drilling rates. In Berea sandstone there was a large reduction in relative drilling rate with both the oil and water muds that contained low percentages of emulsified fluid. Dynamic filtration rates of water muds on rock did not always decrease with increasing oil percentages even though the static API filtration rates on paper did decrease. Data observed in laboratory drilling of limestone and sandstone indicate that improvements in field drilling operations when water- or oil-emulsion muds are wed may not be the result of increased drilling rates but of improved hole conditions. In some cases, actual drilling rates might be slower but improved hole conditions will result in less total time on the hole. DEFINITIONS Mud pressure—Pressure of drilling fluid as measured after leaving the drilling chamber. This is considered as the approximate mud pressure just past the bit and at the face of the formation. Terrastatic pressure—Pressure representing weight of overburden. Formation pressure—Pressure of formation fluid as measured at outlet of drilling chamber. This is considered as approximate pressure of fluid in the pores of the formation. Differential pressure—Difference between the mud pressure and formation pressure. Relative drilling rate, percent—Drilling rate with experimental fluid divided by drilling rate with water times 100 equals percent. LABORATORY EQUiPMENT AND TESTING PROCEDURES The drilling equipment has been described in previous publications The microbit drill is a closed system (capacity, approximately 7 gal) that can be pressurized to 15.000 psi and heated to 500F. Main components are a drilling chamber, filter-heater, rotary-drive and variable-speed cir-

By D. Donald Downey

Pilot Testing Ion Exchange Resin (IEX) can go from very simple beaker testing to complicated column testing. Space velocities, regenerant quantities, loading capacities, ion leakage, are all terms that get accumulated together to prove or disprove a resin’s (or resins’) ability to load a single ion (or specific set of ions). Not getting all the resin’s operating parameters correct will disqualify (or at least skew) the results. Laboratory tests for capacity, moisture content, bead size, metals fouling, etc.—what does it all mean? At last count, there were over twenty-five separate ion exchange resin tests (analyses) that were available to end users. Standard testing procedures identify the resin properties but more specific procedures can be used to identify problems with equipment operation. Then, there are the costs to consider; simple cation resin testing (moisture content, total capacity and bead integrity) is in the $200/sample range. However, add to this Chatillon, Russian Ball Mill Test, HIAC particle size, metals and % regeneration test procedures and the lab work can increase to over $1000/sample. In this paper, the author will explain the “must-do” pilot and test procedures and why they are important and the key to understanding how resin performs ion exchange.

By O. Norman Lotter

There are many scales of innovation in the pursuit of concentrator performance improvement, including paradigm change, inventive change and incremental change. All are important, but the last is low risk, low cost and has a relatively high probability of success, given the right metallurgical skills. Seeking continuous improvement is also essential to ensure that performance does not decline over time due to ore type changes, personnel changes, equipment wear and other factors. When properly implemented, these small gains offer a very high rate of return for the project cost because they are made from marginal, not total, operating costs of the plant. To be effective this approach requires plant trials that use designed structure and appropriate statistics to test the observed differences arising from the old and new process treatments, be they a change in flotation reagent, in grind, pulp density, etc. However the pursuit of small but financially significant performance gains is often regarded as fruitless because of the range of variance in plant data, and the consequent difficulty of ‘proving’ that a benefit has been achieved. Opportunity for improvement is thus sometimes relegated to the realm of the impossible, or at best, treated with skepticism. Operations managers prefer to look for the larger gains, which are easier to demonstrate and prove. Unfortunately, these are seldom to be found; rather, a large gain can be more easily made by executing a series of small recovery improvements that are together equivalent to the ephemeral single large gain. In this paper we advocate a policy of continuing improvement driven by rigorous performance testing protocols and a formal ‘risk analysis’ approach to judging the efficacy of changes implemented in the plant. Following these simple procedures allows rational decisions to be made on the basis of quantifying risk and reward. In particular we consider the choice of hurdle rate for decision-making which best balances risk and reward. It is shown through case studies from actual industrial practice that this approach is practical and delivers significant financial value to the operation.

By F. N. Kissell

The machine-mounted continuous respirable dust monitor (MMCRDM) is a fixed-location area sampling device developed for possible use at the working face of an underground coal mine. This device, based on proprietary technology known as the tapered element oscillating microbalance, has evolved over the past eight years through a cooperative effort of the former Bureau of Mines, MSHA, and the Rupprecht & Patashnick Company in Albany, NY. The capability to measure respirable coal mine dust levels on a continuous basis, rather than depending solely on periodic samples obtained from the traditional coal mine dust samplers, has been a goal in the mining industry for nearly two decades. Recently, an extensive series of laboratory and underground tests was conducted by NIOSH with the cooperation of MSHA and coal operators to test the performance of the MMCRDM In preliminary laboratory testing, the MMCRDM seemed to work well. However, in every underground test, when compared to reference samplers placed close to the inlet, the MMCRDM failed to meet the 25% accuracy criterion specified in the contract under which it was developed. Two reasons explain this failure: First, in most tests the bias (the relative discrepancy between the average MMCRDM concentration and the average reference sampler concentration) was too great. Second, the variability of the samplers used for reference comparison was too large. Finally, the underground testing of the MMCRDMs showed that they are quite unreliable at this stage of development. In the majority of mine tests, no more than 10 shifts of data were taken before the MMCRDM failed to function properly. Major breakdowns, requiring the return of the MMCRDM to the factory for repairs, occurred on average every 28 days. To be considered mine-worthy, MMCRDM reliability must be substantially improved. KEYWORDS Dust, coal dust, dust instrumentation, dust sampling, dust monitoring, black lung, pneumoconiosis

By David J. Hatem

Tunnels and underground projects are inherently more risky than vertical projects, which typically utilize more conventional design and construction approaches and are undertaken in the context of relatively ascertained and defined conditions. On tunnel and under-ground projects, there are a host of special risk factors, including unknowns and uncertainties as to the physical and behavioral characteristics of the ground, the inextricable interdependence and necessary interaction of design decisions and construction means and methods with those ground conditions as well as the manner in which risks are allocated among project participants for un-anticipated subsurface conditions. Public-private partnerships (PPP) projects, in their own respects (and independent of any major subsurface component), pose significant risk for all private sector participants. The main driver of owners to procure projects using PPP is financial, as often all, or substantially all, of the design and construction risk are transferred to the private sector consortium, including the design-build (D-B) team. For a concerning number of those public owners, that risk transfer regime includes rather onerous and aggressive contractual terms that allocate to the private sector participants substantially all risks associated with the encountering of unanticipated subsurface conditions. These aggressive risk allocation provisions, while directly impacting project participants upstream of the consulting engineer, have an indirect and corresponding risk intensifying effect upon consulting engineer professional liability exposure. There are many factors that result in increased professional liability exposure for consulting engineers involved in PPP projects. The more prominent and prevalent of those factors fall into the following categories:

By N. C. J. Ros

The paper deals with pressure gradients occurring in flowing and gas-lift wells, a knowledge of which can be applied to the determination of optimum flow-string dimensions and to the design of gas-lift installations. The study is based on a pressure-balance equation for the pressure gradient. It appears that a pressure-gradient correlation of general validity must essentially consist of two parts-—one part being a correlation for liquid hold-up and the other part being one for wall friction. Dimensional analysis indicates that both liquid hold-up and wall friction are related to nine dimensionless groups. It is shown that in the field of interest only four groups are really important. On the basis of these four groups a restricted experimental program could be selected that nevertheless covered practically all conditions encountered in oil wells. This experimental program has been carried out in a laboratory installation. Three essentially different flow regimes were found. The pressure gradients in these regious are presented in the form of a set of correlations. Comparison of these correlations with a few available oilfield data showed excellent agreement. INTRODUCTION Prediction of the pressure drop in the flow string of a well is a widely known problem in oilfield practice. Accurate data on the pressure gradient of a simultaneous flow of gas and liquid in a vertical pipe are especially useful for the determination of optimum flow-string dimensions. It is well known that with moderate gas and liquid flows such a vertical string acts as a "negative restriction". The pressure drop decreases (1) when the throughput through a given pipe increases, and (2) when at a given throughput the cross-sectional area is decreased. The reason is that, with increasing velocities, the flow becomes more agitated so that the gas slips relatively more slowly through the liquid. With the resulting increase in gas content in the string, the static head decreases. When the area becomes very small, however, the high velocities entail great wall friction, which causes an increase in pressure drop. For a given flow, therefore, minimal pressure drop is obtained by using a certain cross section. This means that, in principle, each well can be provided with an optimum flow string for minimum pressure drop and, hence, maximum possible production rate. The procedure for the selection of the optimum string has been discussed by Gilbert.' A necessary tool in the procedure, however, is accurate knowledge of the pressure gradient to be expected for various values of the governing variables. Another application of pressure-gradient data lies in the field of gas-lift practice: they provide a means of determining the optimum gas-injection rate, optimum injection pressure and optimum injection depth. Much work has already been done in the study of the pressure gradient of vertical gas-liquid flow. Poett-mann and Carpenter2 presented a pressure-gradient correlation based on measurements in wells. This correlation has been found to provide accurate predictions in high-pressure wells and in high-production wells for flow through both tubing and annuli.2-5 However, when their method is checked on low pressure-low production wells or on wells with viscous crudes, serious discrepancies are found. As we shall see in the next section, this is due to the fact that their correlation factor, representing all irreversible energy losses, is given as a function of only one correlation group. Some important variables, such as gas-liquid ratio and liquid viscosity, are not incorporated in this group so that their specific effects are not accounted for. To study also the mechanism of vertical gas-liquid flow outside the ranges covered by the Poettmann-Carpenter publication and extensions, a laboratory investigation has been carried out. This study is founded on a pressure-gradient equation that is based on a pressure balance. To reduce the number of test runs required, a dimensional analysis has been carried out, followed by a selection of relevant dimensionless groups. These groups guided a subsequent experimental study, and with their aid the experimental program could be minimized while still covering the majority of the situations encountered in oilfield practice. In this paper the choice of a formula for the pressure gradient is discussed first. This is followed by a brief description of the experimental setup. Subsequently, the dimensional analysis is discussed and the relevant dimensionless groups are selected, resulting in the experimental program required. The general relationships of pressure gradient and liquid hold-up are then described; various flow patterns and a certain flow instability (so-called "heading") are discussed and a set of correlations is presented which shows a good agreement with the measurements and a few available field

By C. S. Griffith

Lithium Australia NL (ASX:LIT) and ANSTO Minerals have been working together since 2015 on the development of halide accelerated leaching for the extraction of lithium from lithium-bearing micas, spodumene and clays. This technology has been termed SiLeach® process. The driving force behind development of the SiLeach® process, initially, was to develop a hydrometallurgical process to extract lithium from micas and spodumene without the need for the energy intensive, high temperature processing conventionally applied to lithium extraction. This driving force remains today and continues to hold promise in realising the value of previously under-utilised lithium resources. A comprehensive understanding of the technology and its applicability to the processing of micas and spodumene currently exists, and the flowsheet has been rigorously piloted. Production of battery grade lithium carbonate has been demonstrate