Search Documents

By D. R. Wieland, H. T. Kennedy

The object of the work reported here was to determine the content of elemental sulfur in gaseous methane, carbon dioxide, hydrogen sulfide, and in mixtures of these gases, at pressures and temperatwes encountered in natural gas reservoirs. Sulfur content at equilibrium is reported for pure methane, carbon dioxide, hydrogen sulfide, and on three binary mixtures of each of the three pairs of gases at pressures of 1,000, 2,000, 3,000, 4,000, 5,000 and 6,000 psia and at temperatures of 150°, 200° and 250°F. In addition, the sulfur content of three ternary mixtures at the same temperatures and pressures are reported. The results indicate that the sulfur content is higher in the gases at higher temperatures and pressures. The content is highest in hydrogen sulfide, intermediate in carbon dioxide and lowest in methane. INTRODUCTION At ordinary pressures and temperatures, the concentration of a nonvolatile material, such as sulfur in a gas at equilibrium, is a function of the vapor pressure of the material and is independent of the nature of the gas. As the pressure and temperature increase, the gas assumes some of the properties of liquids, including the power to dissolve other liquids and solids, to an extent dependent on the nature of both the gas and the material dissolved. At equilibrium, the content of sulfur in the several gases considered here may thus be considered as solubilities which are fixed for a given composition of gas, temperature and pressure. The study of the solubility of elemental sulfur in gases is of interest because sulfur is sometimes present in reservoirs producing natural gas and must be present in the vapor phase. Upon reduction of pressure and temperature, the sulfur precipitates from solution in the reservoir and in the tubing and fittings. Due to the fact that the greatest pressure drop in the reservoir is around the wellbore, the volume of sulfur precipitated will be greatest in this locality and can cause a substantial reduction in the permeability of the formation in this area. As the natural gas flows up the tubing string, the pressure and temperature are further decreased, causing further sulfur precipitation. If the volume of free sulfur is large and remedial measures are not taken, complete plugging of the tubing can occur. Knowledge of the content of sulfur as a function of composition, temperature and pressure will enable the operator to determine what changes in pressure and/or temperature are necessary to keep the sulfur in solution. If the sulfur solubility is large and can be controlled, the operator may desire to produce the well at a high wellhead pressure and temperature and reclaim the sulfur at the surface. The high solubility of sulfur in hydrogen sulfide (5.6 per cent by weight at 5,000 psi and 200°F) suggests the feasibility of recovering sulfur by injecting this gas into sulfur-bearing reservoirs and expanding the produced gas to precipitate out the sulfur. The present project was designed to measure the solubility of sulfur in carbon dioxide, methane, hydrogen sulfide and mixtures of these three gases at various temperatures and pressures. These gases were the major constituents of the gas well where plugging by sulfur was encountered. A study of the published literature shows no data on the solubility of sulfur in any gas, although Hannay and Hogarth,' in 1880 reported that it was soluble in carbon disdlide above the critical temperature of carbon disulfide. EQUIPMENT AND PROCEDURE Fig. 1 shows the layout of equipment employed to bring gases to equilibrium with sulfur and to isolate the quantity of sulfur contained in a known volume of gas. Pure gases were measured in the charging bomb at known temperatures and pressures and displaced into the reservoir bomb to make up the desired mixtures. When equilibrium was achieved

By A. A. Venghiattis

A rational approach to the selection of the appropriate perforator to use in each specific zone of an oil well is presented. The criteria presently in use for this choice bear little resemblance with actual down-hole condilions. These environmental conditions affect the elastic properties of rocks. One of these elastic properties, acoustic velocity, is suggested as the leading parameter to adopt for the choice of a perforator because, being currently measured in the natural location of the formation, it takes into account all of the effects of compaction, saturation, temperature, etc., which are overlooked in the laboratory. Equations and curves in relation with this suggestion are given to allow the prediction of the depth of perforation of bullets and shaped charges when an acoustic log has been run in the zone to be perforated. INTRODUCTION When an oil company has to decide on the perforator to choose for a completion job, I wonder if it is really understood that, to date, there is no rational way of selecting the right perforator on the basis of what it will do down-hole. This situation stems from the fact that the many varieties of existing perforators, bullets or shaped charges, are promoted on the basis of their performance in the laboratory, but very little is said on how this performance will be affected by subsurface conditions such as the combination of high overburden pressure and high temperature, for example. The purpose of this paper is to show the limitations of the existing ways of evaluating the performance of perforators, to show that performances obtained in laboratories cannot be extended to down-hole conditions because the elastic properties of rocks are affected by these conditions and, finally, to suggest and justify the use of the acoustic velocity of rocks, as the parameter to utilize for the anticipation of the performance of a perforator in true down-hole environment. EVALUATING THE PERFORMANCE OF A PERFORATOR It is natural, of course, to judge the performance of a perforator from the size of the hole it makes in a predetermined target. Considering that the ultimate target for an oilwell perforator is the oil-bearing formation preceded in most cases by a layer of cement and by the wall of a steel casing, the difficulties begin with the choice of an adequate experimental target material. For obvious reasons of convenience, the first choice that came to the mind of perforator designers was mild steel. This is a reasonable choice for the comparison of two perforators in first approximation. Mild steel is commercially available in a rather consistent state and quality, and is comparatively inexpensive. The trouble with mild steel is that it represents a yardstick very much contracted; minute variations in depth of penetration or hole diameter and shape may be significant though difficult to measure. The penetration of projectiles in steel being a function of the Brinell hardness of the steel (Gabeaud, O'Neill, Grun-wood, Poboril, et al), it is often difficult to decide whether to attribute a small difference in penetration to a variation on the target hardness or to an actual variation on the efficiency of the projectile. Another target material which has been widely used for testing the efficiency of bullets or shaped charges in an effort to represent a formation—a mineral target as opposed to an all-steel target—is cement cast in steel containers. This type of target, although offering a larger scale for measuring penetrations, proved so unreliable because of its poor repeatability that it had to be abandoned by most designers. The drawbacks of these target materials, and particularly their complete lack of similarity with an oil-bearing formation, became so evident that a more realistic target arrangement was sought until a tacit agreement was reached between customers and designers of oilwell perforators on a testing target of the type shown on Fig. 1. This became almost a necessity about seven years ago because of the introduction of a new parameter in the evaluation of the efficiency of a perforator, the well flow index (WFI). The WFI is the ratio (under predetermined and constant conditions of ambiance, pressure and temperature) of the permeability to a ceitain grade of kerosene of the target core (usually Berea sandstone) after verforation. to its vermeabilitv before perforation. The value of this index ;or the present state if the perforation technique varies from 0 to 2.5, the good perforators presently available rating somewhere around 2.0 and the poor ones around 0.8, There is no doubt that, to date, the WFI type of test is by far the most significant one for comparing perforators. It is obvious that a demonstration of a perforator

By William Gleason

Despite a global slowdown in most mining sectors, Caterpillar, the world?s largest mining equipment maker continues to forge ahead with new, and improved offerings to the global mining industry. On Nov. 10, as part of its Loading and Hauling Mining Focus Session at its Tinaja Hills proving grounds south of Tucson, AZ, Caterpillar unveiled to customers and media its two latest mining products, the 994K wheel loader and 6020B hydraulic shovel. The Caterpillar 994K wheel loader builds on a nearly 25-year history of the 994 model but with one noticeable difference ? the 994K is bigger ? much bigger. Weighing in at 239,142 kg (527,218 lb) the 994 K is up to 20 percent larger and comes with up to 30 percent increase in payload capacity. This behemoth of a machine is currently being tested at Caterpillar?s Tucson Proving Grounds, Anglo Gold Ashanti?s Cripple Creek and Victor gold mine in Colorado and Taseko?s Gibraltor copper and molybdenum mine in British Columbia, Canada.

Pillars with width to height ratios of less than 1.0 are frequently created in underground hard rock mines. The strength of slender pillars can be estimated using empirically developed equations. However, the equations can provide variable results when the width-to-height ratios approach 0.5. This paper investigates some of the issues affecting pillar strength at low width-to-height ratios in hard brittle rock. The investigation includes an evaluation of empirical pillar strength data presented in the literature and observations of pillar performance in underground limestone mines in the eastern United States, supplemented by numerical modeling in which failure processes and sensitivity of slender pillars to variations in rock mass properties are evaluated. The results showed that the strength of slender pillars is more variable than that of wider pillars. The numerical model results demonstrated the increasing role of brittle rock failure in slender pillar strength. The absence of confinement in slender pillars can result in a fully brittle failure process, while wider pillars fail in a combined brittle and shearing mode. The onset of spalling in slender pillars occurs at or near the ultimate strength, while this is not the case for wider pillars. Slender pillars are shown to be more sensitive to the presence of discontinuities than wider pillars, which can partly explain the increased variability of slender pillar strength. Two examples are presented, which illustrate failure initiation by brittle spalling and the sensitivity of slender pillars to the presence of discontinuities.

By L. F. Elkins

Water coming into wells with bottom water present in the Fosterton field, when their oil recovery was only 0.1 to 1.5 per cent of oil in place below the lowest perforation, confirms lack of shale barriers to vertical flow which also are not apparent in cores and electric logy. Low contrast of vertical and horizontal permeability, high mobility ratio betweerz oil and water zone and pos.rible rate effects due to gravity Combine to prevent easy analysis of water invasion pattern and efficiency by analogy or intuition. Theoretical analysis of performance including these factors using a new direct nurnerical .solution of potential distribution in a network led to unanticapted indications that water would under-run the entire oil reservoir with low volumetric coverage if supplied through natural influx or peripheral water injecfion below the oil-water contact. An unusual pattern of water injection is to he adopted in this recently unitized pool to provide more uniform water flooding in that two-thirds of the oil reservoir not underlain by bottom wafer. INTRODUCTION The Fosterton field, Southwestern Saskatchewan, Canada, was discovered in Jan., 1952. It produces at a depth of 3,100 ft from a pinch-out of the Roseray sand at the Lower Cretaceous-Jurassic unconformity. The field, covering 2,500 acres, contains 54 wells on 40-acre spacing. Development was essentially complete in June, 1954, but significant production did not start until May, 1955, when a pipeline outlet became available. Within one year rapid in- creases in gas-oil ratio and early encroachment of water created operating problems in the down-structure eastern half of the field and raised serious questions about reservoir performance and ultimate recovery. This paper describes the unusual behavior of water encroachment—on both well and reservoir bases—and the analyses made to interpret it. The field was unitized July 1, 1958, for water flooding. A somewhat unconventional

By M. Felsenthal

Engineers are frequently faced with the problem of having to predict oil recovery from a solution gas drive reservoir in the early life of a field. This is often the time when actual laboratory or field-derived gas-oil permeability (kg/k0) data are not yet available. Although excellent collections of k0/k0 data for various types of rocks may be found in the literature,1,2,3 a need exists for a more detailed correlation of k0/k0 data with core properties such as porosity, permeability, clay content or pore-size distribution. It is the purpose of this article to present this type of correlation for sandstone material. The correlation is based on laboratory tests performed on over 300 core samples from 19 reservoirs in the United States and Canada. EXPERIMENTAL Cores were analyzed by routine procedures, using samples of conventional size (7/8-in. diameter, 7/8-in long) cut parallel to the bedding planes. Air permeability was measured at 1.67 atm mean pressure in a Hassler-type apparatus. Porosity was determined with the aid of a Ruska bulk volume meter and a Boyle's Law rock volume meter, An evaporation method' was used to evaluate irreducible water saturations. Core samples were saturated with 25,000 ppm NaCl brine. The brine was reduced to the irreducible saturation, and the remainder of the pore space was filled with kerosene. This was followed by multiphase flow tests using the so-called "dispersed feed" technique.5 n this technique, gas and oil (kerosene and kerosene-saturated air) were dispersed with the aid of a porous Alun-durn feed head, the face of which contained a waffle-shaped system of Lucite-lined grooves. Oil entered the back side of the feed head and emerged at the raised areas of the front face. Gas was introduced directly into the system of grooves at the front face. The gas-oil mixture then entered the test core which was kept in capillary contact with the feed head. Permeabilities were determined from rate and pressure measurements and saturations from weights. All determinations were performed at equilibrium or steady-state conditions. Pore-size distributions were determined on selected samples by a mercury injection technique.6 GENERAL CORRELATIVE TRENDS When examining data from a given reservoir, it was noted that k0/k0 vs saturation curves became generally less steep as specific air permeability increased, a development that has a favorable effect on oil displacement efficiency by solution gas drive. This trend has also been reported by others in the literature.' An effect of porosity on k0/k0 data was also noted. This effect was not generally discernible in a study of relative permeability data for a given reservoir but became apparent when data for sandstone reservoirs of similar lithology but differing average porosity were compared. For instance, in a comparison of argillaceous and/or calcareous sandstones from 11 reservoirs ranging in average porosities from 14 to 28 per cent, a definite trend was noted, indicating that for a given permeability k0/k0 curves became less favorable (i.e., steeper) as porosity increased. A similar trend was observed for a group of comparatively clean sandstones from five reservoirs ranging in average porosities from 15 to 21 per cent. For a given permeability and porosity, comparatively clean sandstones gave more favorable k0/k0 curves than argillaceous and/or calcareous sandstone or chert reservoirs. The laboratory studies also showed that least favorable k0/k0 curves were exhibited by shaly sandstone, conglomerate, and sandstone containing carbon inclusions. Table 1 lists the various source reservoirs classified by lithology types. To facilitate a correlation of k0/k0 data with core characteristcis, it was found expedient to work with

By L. T. Stanley

A method is described whereby the behavior of the front is approximated when gas is injected into a thick reservoir having reasonably homogeneous properties. The method is applied to the Abqaiq field of Saudi Arabia. The producing member is the Arab-D, a high-permeability calcarenite which has no continuous betlding planes. Field performance indicates the injected gas to be partially miscible with the reservoir oil because gas volume factors experienced are lower than those predicted by the gas law. Eqlrilibril~m calculations confirnz ihis and also show that the volume factor may vary appreciably, depending on the relative quantities of oil and gas in contact in the reservoir; consequently, volutnetric balances are made for the purpose of determining the behavior of the gas volume factor during injection history. The effect of gravity segregation on position and shape of the gas front is approximated by dividing the producing section into three zones vertically and tracing the movement of the average interface in each zone, with counterflow of oil and gas taking place betweell zones behind the front. This results in a gas front that advances more rapidly along the top of [he formation than along the base, producing an "umbrella" effect in cross section that becomes more pronounced as the front progresses. The calculations cover the gas-injection period of Abqaiq field history through 1958, and the position of the gas front is plotted at one-year intervals. Finally, some comparisotls between the calcrlated fronial position and the gas-oil contact as Measured by neutron logs are made. INTRODUCTION Fig. 1 is a structure contour map of the Abqaiq field. For analytical purpcses, the field has been divided into two areas designated A and B, as shown on the map. Gas injection into Area A was begun in early 1954 into two wells located near the crest of the structure on the north-south axis of the anticline. During the period covered by this paper, the average injection rate has been 122 MMscf/D with a maximum sustained rate of 160 MMscf/D. The reservoir pressure has been maintained at 2,450 psig since start of gas injection. The reservoir originally was undersaturated but, prior to pressure maintenance, the pressure was drawn below the bubble point in most of the Area A section, creating an in-place free-gas saturation of 8 per cent at the crest of the structure. The average critical gas saturation is 13 per cent established by laboratcry core tests. That the entire reservoir remained below critical gas saturation prior to gas injection is borne out by the fact that none of the crestal wells have exhibited high gas-oil ratios during production history. The Area A reservoir is a carbonate section about 200-ft thick having average porosity and permeability of the order of 22 per cent and 500 md, respectively. The productive horizon is the Arab-D member of Jurassic age and is encountered at an average depth of

By Isaac A. Zlochower

A number of ignition incidents involving mining and farm equipment have illustrated the surprising danger of drilling, cutting, or otherwise penetrating sealed compartments or frames that are filled with metal scrap for ballast. The presence of chemically-reactive metals (or electrochemically-active pairs), such as zinc in galvanized steel, can produce hydrogen from moisture in the steel scrap, and the resulting pressure, due to the internally-generated hydrogen, can produce an easily-ignited gas jet when the sealed component is penetrated.

This paper on the relation of Granite and Sedimentary Contacts to Victorian Mining will, it is hoped, be of interest to members of the Institute.The broad fact that gold often occurs' at or near the junction of granite with sedimentary silurian or metamorphic rocks has been noted by some Victorian geologists, miners, and prospectors; but the fuq practical value -of the fact does not seem to have been fully realised by prospectors. Glancing at the Geological" Map of Victoria, one can see that many of our goldfields 'are situated at or near the junction of granite with Palceozoic sedimentary formations, and that some of our alluvial fields are on granite. Many prospectors are possessed of this knowledge but when prospecting a contact locality, they would be just as likely to confine their search for auriferous matrices to spots a quarter of a mile on the sedimentary side, as on the actual contact line of two formations.

By V. S. Tuman

In the first part of this paper, an estimate is made of the magnitude and extent of the thermal stresses which result from mud circulation. Our study is made for the period of relaxation, i.e., when the drilling operations are terminated and mud circulation is discontinued. In the second part, we have shown how the thermal stress can affect the wave propagation. An example is worked out for a Carbondale sandstone (Illinois basin). It is concluded that, in extreme cases when differential temperature is about 100°F, the travel time will be affected by about 2 microsec/ft. For more refined permeability studies, such corrections would be desirable. MAGNITUDE AND EXTENT OF THERMAL STRESSES RESULTING FROM MUD CIRCULATION When geological beds are penetrated by boreholes, it is observed that the formation temperatures increase with depth; however, the temperature profile varies considerably from place to place. During drilling operations, mud pumped from a pit at atmospheric temperature absorbs heat from the lower beds. As a result, the drilling fluid returning to the surface is at a higher temperature than the surrounding beds. The temperature gradient in a well depends on the rate of mud circulation and other factors; normally, this temperature gradient is smaller than the natural gradient in the formations. (See Fig. 1.) The temperature difference between the mud column and the surrounding beds gives rise to therma1 stresses (which are also important in the phenomenon of fracturing), and it is expected that they will affect the transit time of the sonic front in velocity logging.1 It is evident chat beds near the surface will undergo various cycles and will have a complicated dynamical and thermal-stress history. A limestone bed which is just penetrated will act as a source of heat, warming up the cold mud pumped down a few minutes earlier from the surface pit. The same limestone bed a week later will act as a sink, absorbing heat from the drilling mud which has already warmed up sufficiently to be at a higher temperature than the bed in question. No doubt a large section of the hole will undergo a heat treatment, which will make the calculation of the exact magnitude of the thermal stresses very difficult. In the solution of wellbore thermal equation, it is assumed that the rock around the wellbore is elastic and isotropic, and that the system is radially symmetrical. A complete dynamical solution of the thermal stresses set up at different horizons during the drilling operations would require a comprehensive history of the mud circulation, the surface temperature of the pit and the number of hours in which mud was not circulated. CONDUCTION OF HEAT AND THERMAL EQUATION OF STATE

By T. K. Perkins, L. E. Bartlett

Values of rock surface energy (i. e. energy required to form a unit area of new surface) are useful for interpretation of drilling and fracturing phenonema This paper describes the adaptation of a cleavage technique (splitting of large rocks under controlled conditions) for measuring surface energies. Values of surface energy obtained at room temperature and at low crack extension rates are reported for a variety of sandstones and limestones. Elastic moduli, tensile strengths and compressive strengths of the samples are also reported. The values of Young's moduli (measured in bending) are relatively low, probably because of the low stress levels imposed. Measured values of surface energy me generally higher than anticipated and probably reflect inelastic yielding near the extending tip of the crack. INTRODUCTION The technology of petroleum production includes many operations such as drilling and fracturing, which involve rock breakage. One of the fundamental properties of a rock needed to fully explain breaking and fracturing phenomena is the surface energy (i. e. the energy required to form a unit area of new surface). In this paper we describe an adaptation of the cleavage method (splitting of the rock under controlled conditions) to utilize large rock samples. Application of the theory of elastic cantilever beams and the Griffith concept of mechanical stability permits the calculation of surface energies from simple measurements. Values of surface energies obtained at room temperature on dry samples and at low crack extension rates are reported for a variety of sandstones and limestones. Measured values of Young's Moduli, compressive strengths and tensile strengths are also reported for the rocks. THE EXPERIMENTAL METHOD Equipment designed to cleave large rock samples is shown on Fig. 1. This equipment consists essentially of two steel blocks cemented to a rock sample and forced apart with a steel rod. A ball joint and a pivot prevent bending stresses in the rod. A differential thread arrangement permits the rod to advance only 0.012 in./revolution of the driving nut. The axial force in the rod is measured with type FA-50-12 Baldwin Lima Hamilton strain gauges and a BLH type 20 strain gauge reader. Separation of the blocks is measured with a Starrett 656617 dial gauge. The massive nature and design of the equipment minimize the amount of elastic energy stored in the steel parts as the stress in the rod is increased. This will permit the rock to split under controlled conditions as will become clear later. Fig. 2 shows a sketch of the rock sample during cleavage. Guide slots are cut longitudinally along the rock sample as suggested by Berry.1 An initiating slot is also cut across the top of the block to a depth of 1 to 2 in. During cleavage, elastic energy is stored in the flexed beams of rock of length C. If the length of steel rod L is held constant and the crack extends in length, then the elastic potential energy stored in the rock decreases. However, surface energy must be supplied as the crack extends in length. Griffith6 has proposed the following criteria for mechanical stability. The crack will extend as long as the potential energy available is greater than the surface energy required. However, the crack will stop extending when the change in potential energy with change in crack length is just equal to the change in surface energy with change in crack length. See Eq. 1.

By T. D. Mueller

Many investigators have used the response of the "dimensionless aquifer" to a unit pressure drop or a unit fluid-withdrawal volume to calculate the performance of an aquifer in supplying water influx to an oil reservoir. In the past, these response functions have been calculated with the aid of the Laplace transform. With the advent of ultra highspeed digital computers, it becomes practical to solve for the response functions with finite-difference techniques. The computer method also permits extension of the dimensionless-aquifer concept to include the nonhomogeneous aquifer wherein the permeability and other properties vary as a function of the space co-ordinates. This paper gives results of calculating the response functions for a series of nonhomogeneous aquifers. Response functions are presented for both linear and radial aquifers whose thickness, permeability-viscosity ratio and porosity-compressibility vary. These functions are new and should prove useful to the petroleum engineer in analyzing the behavior of nonbomogeneous aquifers. Results are presented in the form of charts that can be easily used by the field engineer. INTRODUCTION Aquifers which surround many oil and gas reservoirs have the ability to supply water influx to such reservoirs as oil and gas are withdrawn. This water influx, called natural water drive, provides one of the most effective driving mechanisms for the production of oil and gas. In producing a reservoir, therefore, it behooves one to make the maximum use of natural water drive. To achieve the maximum use, the reservoir engineer must be able to predict the performance of an aquifer under a variety of production schemes that may be proposed for the reservoir. Unfortunately, the physical properties which dictate aquifer behavior often are known only within limits. Seldom do wells penetrate the porous strata of the aquifer. Even when they do, quantitative information regarding porosity, permeability and water compressibility is seldom available. It is known, however, that the water efflux from most aquifer systems is governed by a single, relatively simple, linear, partial differential equation. Also, the general physical location of the aquifer boundaries often are known. A technique originall proposed by Hurst1 and van Everdingen and Hurst2 has been found useful in analyzing reservoirs in this situation. The idea was later expanded by van Everdingen, Timmerman and McMahan3 to include the mathematical technique of least-squares fitting. This latter method will be referred to as the VTM method. The basic assumptions of the VTM method include the following. 1. The location of the physical boundaries of the aquifer are known. 2. The flow conditions at these physical bound-daries are also known. 3. The aquifer is homogeneous; e.g., thickness, permeability, water compressibility and porosity are constant throughout. In the VTM method, a material balance is made on the fluids entering and leaving the reservoir. In the balance equations, the water-influx term is represented as the product of the water influx from an arbitrarily-selected, dimensionless aquifer system times an unknown conversion number. This balance can be formed as many times as there are data points in the history of the reservoir. Each time, the conversion number can be evaluated. If the reservoir engineer has picked the correct dimensionless aquifer to represent the real aquifer, the conversion number remains constant for all balances that have been made over the history period. If such a situation occurs, the reservoir engineer can then predict the performance of the reservoir for any type of production scheme by using the function associated with that particular dimensionless system and the derived conversion number. These functions will be referred to as the response function of the aquifer. If the aquifer is nonhomogeneous (e.g., if the porosity, permeability, thickness, porosity, or

By R. L. Robinson, P. DeFrank, R. F. Hatfield

Production equal to or greater than open-hole completions is possible through perforated completions if the flow paths throughout the perforations are free of obstructions.' Previous investigations have indicated that, in some cases, maximum productivity is not obtained due to plugging of the perforations with debris from the wellbore fluid and/or debris from the perforating process. Control of wellbore fluid and proper well completion techniques are very important in the elimination of perforation plugging.' Selection of properly designed perforating equipment also is quite important for maximum well productivity. Studies made with the use of the perforation flow laboratory, in which perforating tests are run under simulated well conditions, have shown that perforation plugging occasionally occurs. Plugs in perforations result from various causes. One of the contributors to plugging that can be controlled by the perforating device is the slug or carrot resulting from jet perforating. This condition has undergone extensive study, and previous developments have resulted in a decrease in carrot size—but not in complete elimination. It was felt that, if a method of completely eliminating the carrot could be found (with charge performance equal or better than previously obtained), a significant contribution would have been made. Such a charge has been developed and is reviewed in this paper. THEORETICAL CONSIDERATIONS OF CARROT ELIMINATION There are several popular theories of how a shaped charge jet is formed."," One of these is the hydrodynamic theory, wherein the liner is treated as a fluid under the impact of the explosive forces. Another is the spalling theory, where the interaction of shock waves in the liner causes small particles to be torn from the inner surface of the liner and projected at high velocity toward a common focal line to form the jet. It is not unreasonable to assume that both of these theories may be partially correct. For purposes of our discussion, it is simpler to use the second theory. Generally speaking, when a plate of metal is attacked by an explosive shock pulse, the pulse is transmitted through the metal at high velocity, as shown in Fig. 1(A). Pressures at the shock front may be 6 X 10' psi or higher. This shock wave (a compression wave) upon striking a free surface, Fig. 1(B), is partially reflected back as a tension wave. The interaction of the tension wave with the decaying compression wave causes a stress concentration in the metal; when this stress becomes great enough, a failure occurs and a small particle flies off and is projected away from the metal surface, as shown in Fig. 1(C). A new free surface is then presented to the shocks; the process repeats itself until there is no longer enough energy to cause failure, leaving a portion of the metal relativcly untouched. See Fig. 1(D). To apply this theory to a perforating shaped charge, consider the flat plate to be folded into a somewhat conical shape, with a column of explosive placed in intimate contact with the cone (Fig. 2). An explosive initiator detonates the charge, creating a shock wave

By John S. Alexander

By Pertti Koukkari

The novel Jarogain process combines treatment of the jarosite residue of zinc manufacturing and processing of arc furnace dust from steelmaking to a holistic recovery technology. The new hydrometallurgical approach is targeted to recover the major constituents (Fe, Zn, Pb) as well as valuable components such as Ag, Au, In and Ga from the jarosite-dust mixture as reusable concentrates. The fractionation process proposed by VTT and Aalto University takes advantage of jarosite being readily fine powder and directly available for wet chemical processing. Jarogain process provides an energy efficient opportunity for jarosite utilization as value added products. The experimental proof-of-concept of key stages of the process will be outlined with a comparison of available pyrometallurgical treatments of jarosite waste. The techno-economical assessment is based on estimated investment and variable production cost using the discounted cash flow (DCF) analysis.

By I. Fatt

The chromalographic effect refers to the separation of constituents in a moving fluid phase which occurs when the phase is passed over a stationary phase, either solid or liquid, or large areal extent. In performing chemical analyses, the large surface contact areal is provided in the case of gas-solid chromatography by-passing the gas over a porous solid and for gas-liquid chronla tog rap hy by-passing the gas over a porous solid which has been coated with a nonvolatile liquid. The porous medium is usually placed in a cylindrical tube, although it may be a relatively flat sheet as in paper chroma-tography. According to one theory,' the separation results from the difference in time spent by various components in the stationary phahe. A gaseous component which is conlpletely insoluble in the stationary phase, or is not adsorbed on the solid, proceeds unimpeded through the column. The versatility and power of the various types of chromatogruphy for the analysis of complex mixtures are evident from their widespread use in performing chemical analyses and from the large number of symposia, books, and papers devoted to the subject in recent years. Associated developments are the application of chromatography to the determination of heats of solution, heats of adsorption, solubilities orK-values, etc. Gas-liquicl chromatography analyses may be characterized by the manner in which the samples are introduced and displaced from the column'. The three techniques used are known as (1) frontal analysis, (3) displacement analysis, and (3) elution analysis. The frontal analysis is performed by displacing an inert gas from the column by a continuous stream of the sample. As indicated in Fig. l(A), all but the first fraction leaving the column represent mixtures rather than pure components. The displacement analysis is conducted by filling the column with a sample, then displacing it with a more strongly adsorbed or absorbed vapor. The resulting chro-matogram is illustrated by Fig. 1(B). Finally, in the elution analysis a small sample of the mixture to be analyzed is introduced as a "plug" into a Rowing stream of carrier gas to give an elution-type chromato-gram. Fig. l(C). The three techniques may be used to provide models to which Row patterns in other physical situations may be compared. PURPOSE OF THE INVESTIGATION The purpose of this investigation was to determine whether natural reservoir rocks, when coated with crude oil, provided sufficient surface areas to give rise to a chromato-graphic separation of light hydrocarbon constituents. The tests were conducted with the light hydrocar-bons in the gaseous state. SANDS TESTED Two sands of widely different permeabilities have been studied: (1) Ventura core (16 md), and (2) Torpedo sandstone core (578 md).Table 1 gives a description of the cores that were tested. With the exception of one frontal-type flow arrangement which was performed on Core 3, the tests were of theelution-type in which a methane-propane mixture was eluted through the core by means of helium. The Ventura core, when impregnated with a weathered crude from the same field, became so impermeable to gas flow that it was necessary to conduct the tests on the granulated cores (Cores 2 and 3).

By I. Peerawattuk

Growing demand for Li-based battery technologies is leading to an unprecedented growth in the lithium industry. Although innovation in battery technologies has pushed lithium into the spotlight, lithium was not always known for its application in batteries. The primary use of lithium—prior to the introduction of commercial lithium-ion batteries in the early 2000s—was in the ceramics, glass, grease, and the medical industry. Before being converted into usable forms, lithium products must be upgraded from the raw material. Processes for recovering lithium may involve: thermal treatment, water leaching, solar evaporation, ion exchange, carbonation, and electrodialysis. Presented, is a historical review of lithium applications and the different techniques of converting lithium-rich minerals and brines into usable products with additional discussion on future lithium extraction processes.

By Weng Fu

In this study, Resin-in-Pulp (RIP) technology is used to separate Pb from a chalcopyrite slurry. Solvent-impregnated resin, Lewatit® VP OC 1026, which contains di(2-ethylhexyl) phosphoric acid (D2EHPA) in a macroporous polystyrene matrix was used, as the functional group exhibits selectivity for Pb over Cu. Adsorption pH, kinetics, as well as resin and CuSO4 concentrations were investigated. The results show that the kinetics of Pb and Cu loading are fast, reaching the adsorption equilibrium within 30 min. The equilibrium pH of 2 was chosen as optimum for operation in order to achieve a high Pb extraction rate and extent as well as selectivity for Pb over Cu. High Cu(II) concentration in solution results in Pb(II) requiring a larger amount of resin for the same degree of extraction. Regeneration and reuse tests show that the loss of adsorption capacity happens in the 1st and 2nd cycles and then the adsorption capacity stabilises for the 3rd cycle.

By J. Schmidl

In non-ferrous metallurgy the service life of refractory materials typically ranges from several weeks up to three years or more and is strongly dependent on operating conditions. To support our customers with the most viable refractory solution for their needs RHI Magnesita follows a structured approach of thermo-chemical calculations, experimental evaluation from lab scale up to industrial field tests and post-mortem analysis of used refractory materials. This paper will give an overview of the RHI Magnesita refractory selection process and the most recent developments of the experimental setup for the so called HF-IF test. This is a dynamic corrosion test that allows to determine fundamental properties of different refractory material types under process conditions subjected with respective customers process materials. The HF-IF experimental procedure is an excellent tool to simulate refractory wear in industrial processes, diminishing risks associated with plant trials and support decision making to choose the optimal refractory solution for the customer.

By C. Liliane Carvalho

In the current study, bio-oxidation tests were carried out in shaking flasks with a flotation concentrate containing the sulphides pyrite, arsenopyrite and gudmidite. The tests were performed with mesophilic microorganisms (At. ferrooxidans) at 30 °C and also with the moderate thermophile S. thermosulfidooxidans, at 50 °C. The effects of (i) previous adaptation of the microorganisms to the concentrate, (ii) ferrous iron concentration and (iii) pulp density (2%, 4% and 6% (w/v)) on the dissolution of the sulphide were studied through arsenic extractions. S. thermosulfidooxidans was more sensitive to the pulp density in comparison to At. ferrooxidans as a reduction in sulphide oxidation was observed with the increase in the solid content to 6%. Therefore, the mesophilic strain was selected for further work, which comprised a rolling bottle experiment at 10% solids. After 40 days of bio-oxidation, the solid material was subjected to cyanidation, which revealed 85% gold extraction as compared to 21% from the original concentrate. The antimony sulphide grains in the bio-oxidized product showed similarity to what was observed in the original sample, suggesting such particles were not susceptible to the bio-oxidation process.