Search Documents

By LINDSAY BOTTOMER, Tassos Grammatikopoulos, Massoud Aghamirian, MARK FEDIKOW

A master composite (Master Comp) sample was prepared from three pegmatite zones from the Zoro Dyke D1 for mineralogical analysis and heavy liquid separation (HLS). The mineralogical examination was conducted on a subsample that was crushed to approximately P80 = 600 μm. The sample consists of spodumene (10.5 percent), quartz (29.3 percent), plagioclase (29.0 percent), K-feldspars (21.3 percent), micas (5.1 percent), tourmaline (2.9 percent) and Fe-Mn-phosphates (0.1 percent). Liberation of spodumene (88 percent) and gangue minerals, including quartz (89 percent), feldspars (94 percent) and micas (83 percent), is very good at this P80 . The average lithium (Li) concentration is 3.7 percent in spodumene, 2,196 ppm in micas, 1,001 ppm in tourmaline and 115 ppm in K-feldspars. Spodumene accounts for 96 percent of the total Li in the sample. The mineralogical data indicate the potential to recover spodumene by flotation with minimal Li losses due to other Li carriers. The HLS was conducted on a subsample that was crushed to smaller than 6.4 mm, with the smaller than 600 µm fraction removed from this test. The HLS results indicate it is possible to produce a high-grade lithium concentrate, with close to 6 percent Li2O, after the rejection of iron silicates with magnetic separation.

By Felipe Calizaya, Sekhar Bhattacharyya

Noise-induced hearing loss (NIHL) is prevalent in mechanized underground mines. Federal regulations are often not complied with effectively. Miners are also prone to ignoring administrative guidelines and/or personal protective equipment for hearing conservation. As a result, quality of life among experienced miners plummets while occupational risks increase at workplaces. This research focused on auxiliary fans used in underground mines. These fans work at high rotational speed and generate extremely high levels of noise in close proximity to miners. Silencers used are often of little effect due to poor maintenance. A new silencer is tried in the laboratory with the objective of easy maintenance and resulting reduction of noise exposure for miners.

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector, which has an important place in terms of raw material and energy supply, is referred as a sector with one of the highest fatal accidents in comparison with other sectors. In this century, where occupational health and safety awareness has increased, it is important to review the past accident statistics and to determine the current deficiencies by using the information in the inventory. In this study, the Malmquist total factor productivity index (MPI) has been utilized to investigate the changes in the work accidents occurring in the Western Lignite Corporation (Turkey), where underground and surface production methods are applied, and to determine the measures to be taken. According to the results obtained, both the decrease in production amount and the increase in the number of accidents caused inefficiencies during the period in concern due to the expected 10-year economic life of the mechanized system operating in the underground production panel that came to an end in 2007 and the flooding took place in early 2017. Compared with the underground operations, it has been determined that production can be carried out at the appropriate scale despite the heavy working conditions encountered due to the changing climatic conditions and the progress of production in the surface operations.

By Joel Lööw, Jan Johansson, Lena Abrahamsson

In this study, we try to illustrate what new technology can mean for the individual miner. We formulate the notion of Mining 4.0, where we attempt to create an image of how the future might look from a miner’s perspective and how mining companies might navigate their way to a future that works for all miners. 

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By Yuanhong Qi, KUN CUI, Tao Fu, XUNFU WANG, Yingyi Zhang, Jie Wang, Junmao Qie

Indonesia is the world’s largest supplier of nickel ore, with its nickel laterite resources mainly distributed in the Moluccas and Sulawesi regions. However, there is scant research on the mineralogical characteristics of nickel laterite deposited in southeast Sulawesi, Indonesia. This study aims to investigate the mineral phase structure, chemical analysis, thermal properties and element distribution characteristics of the middle and lower part of the rotten rock zone located in the southeast Sulawesi ophiolite belt.

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Red mud has been reported as a potential resource for lithium. To investigate the leaching behavior of lithium, a lithium-rich red mud was neutralized with hydrochloric or oxalic acid and then leached with acetic acid. When red mud was neutralized using dilute hydrochloric acid, about 58 to 60 percent of lithium was leached with 25 percent acetic acid at 95 °C for 60 min, while more than 95 percent of sodium and 85 percent of calcium were dissolved in the leachate solution. When oxalic acid was used to neutralize red mud prior to acetic acid leaching, lower lithium leaching efficiencies of about 42 to 47 percent were observed. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the same conditions. In this study, 25 percent (v/v) of acetic acid at 85 °C for 60 min was demonstrated to be the optimum conditions for lithium extraction from oxalic acid-neutralized red mud using acetic acid. The results are useful and of interest for lithium recovery and purification from red mud.

By Gregory M. Rumbaugh, Todd Kostecki, Christopher Mark

From 2015 to 2021, five massive pillar collapses occurred at four underground stone mines in the eastern United States. These events resulted in powerful airblasts that damaged mine infrastructure and mobile equipment, seriously injured miners, and disrupted underground travelways. Each of these pillar collapses propagated through the overlying strata, causing a subsidence basin on the surface. Pillar collapses are particularly hazardous for miners because they can occur with little warning and can affect miners that are far from the pillar collapse area. The following case studies show that certain factors may increase the likelihood of a pillar collapse. For instance, each of the five events involved the collapse of at least twelve benched pillars with width-to-height ratios (w/h) of 0.8 or less. This study elaborates on

By CEM SENSOGUT, OZER OREN, YASAR KASAP

The mining sector, which is important in terms of raw-material and energy supply, is seen as a sector with high number of fatal accidents compared to other sectors. In this century of heightened occupational health and safety awareness, it is important to review past accident statistics and analyze current deficiencies using the information in inventory. Although there are many studies assessing occupational accidents occurring in the mining sector, there are few studies using the nonparametric linear programming method. There are many input and output parameters related to occupational health and safety. Nonparametric linear programming method has been found to be useful because it provides simultaneous evaluation of these input-output parameters, does not require functional form in the analyses and provides guidance on the improvement needed by the related parameter. However, this method analyzes data using a single period of time and does not take into account any changes in efficiency over time. In the literature, there is no study in which the change of occupational accidents occurring in mining and even other sectors over time is examined and the Malmquist total factor productivity index (MPI) is used. Within the scope of the present study, the aim was to examine the change of occupational accidents occurring in Western Lignite Corp. in Turkey, where underground and surface production methods are applied, between 2005 and 2018. It is the first time MPI is used to examine the change of occupational accidents over time. The DEAP 2.1 computer program written by Coelli [1] was used in the solution of the models [2].

By P. L. Crouse, S. J. Lubbe, M. J. Kabangu

A selective extraction and separation of zirconium by solvent extraction with 1-octanol is proposed. The process is based on the dissolution of the metal basic carbonates in hydrochloric acid in the presence of potassium fluoride, using 1-octanol as extractant. The effect of several process parameters, including hydrochloric acid and potassium fluoride concentrations, reaction time, and phase ratio between the aqueous and the organic phase was investigated. Zirconium is enriched in the organic phase. The best extraction and separation results were obtained with the basic carbonate dissolved in 10% hydrochloric acid and 1.5 M potassium fluoride. The optimum reaction time was 15 min with an organic to aqueous phase ratio of 2:1. Based on the selectivity of zirconium over hafnium in the organic phase, a McCabe-Thiele diagram was constructed. A near complete stripping of zirconium from the organic phase was achieved using a 3 M sulphuric acid solution. Additional studies are required in order to determine the reaction mechanism and the chemical speciation of the current investigation.

By Mohammad Ranjbar, Zahra Manafi, FAZAELIPOOR MOHAMMAD HASSAN, HAMGHAVANDI MOHAMMAD RANJBAR, Mahin Schaffie

Bioleaching has an increasingly important place among available mining technologies as biological processes have emerged as alternatives for metal recovery, especially for metals like gold and copper. An important disadvantage of bioleaching is the slow reaction rates, with microbial attack times often lasting weeks. Therefore, applicable research is required to improve these rates. From previous research, copper bioleaching has been divided into two specific regimes: (1) surface reaction controlling step and (2) mix of surface reaction and diffusion controlling steps. The presented model, which includes the effects of both these regimes, predicted the results of copper bioleaching recovery with good accuracy.

By Jonathan Baggett, Nino Ripepi, Amin Abbasi, Richard Bishop, Juan Monsalve, John Hole

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karst voids are complex and challenging ground-control risks. Traditional methods of predicting karst void locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features as reported by Li et al. (J Rock Mechan Geotech Eng:232–242, 2010) and Hassan et al. (Procedia Chem 19:737–742, 2016). Ground-penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in conductivity and dielectric permittivity between limestone and open karst cavities causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries; however, there is a lack of published research on underground mining GPR applications as reported by Zhao et al. (2015a; Geophys J Int:62–71, 2015b) and Eskelinen and Pellinen (Constr Build Mater:888–898, 2018). The purpose of this work is to demonstrate the use of GPR in an underground stone mine and to discuss the importance of karst void detection ahead of mining.

By A. ALLANORE, OLIVEIRA M. DE, D. CICERI, D. P. CHEN

The alkaline hydrothermal processing of K-feldspar rocks in an autoclave can be a pathway to synthesize a potassium fertilizer for tropical soils that is potentially cheaper and more efficient than traditional potash (KCl). When K-feldspar undergoes hydrothermal alteration in the presence of calcium oxide (CaO), it generates a complex mixture of calcium-aluminum-silicate-hydrate (CASH) minerals that incorporate K atoms stochastically in their structure. These atoms are subsequently released, as shown in a test-tube leaching test, indicating a possible uptake by crops. The relationship between the processing temperature and time in the autoclave for the hydrothermal reaction and the resulting mineralogy and elemental release are only partially understood and are investigated in this study. Elucidating that relationship is the key requisite for subsequent techno-economic analysis, and ultimately for the development of a fertilizer that can be considered as a feasible alternative to KCl.

By SHANTAE LEE, ELAHEH TALEBI, Frank A. Drews, ROGERS W. PRATT

Fatigue is a relatively well-investigated topic in the surface transportation industry with a research focus on sleep deprivation and disruption. This paper examines fatigue in mining operations. While mine operators are using or currently introducing technology to monitor fatigue, there is little work that focuses on the operators’ experience of fatigue and the acceptance of fatigue-monitoring technology. Focus groups were conducted to investigate these topics. The results of this research suggest that current fatigue-monitoring systems lack validity, reliability and user acceptance. Overall, these results emphasize the importance of a socio-technical systems perspective to guide interventions aiming at improving miner health and safety.

By K. V. Raj, C. A. Berry, A. T. Weakley, A. L. Miller, P. R. Griffiths, D. A. Parks

Diesel particulate matter (DPM) has been classified as a carcinogen to humans by the International Agency for Research on Cancer. As a result of its potential carcinogenic nature, DPM exposure is regulated by the Mine Safety and Health Administration. Currently, diesel emissions in the workplace are monitored by collecting the aerosol onto filters, which are then sent to a laboratory for thermal-optical analysis using the NIOSH method 5040. This process can take days or even weeks, and workers can potentially be exposed to excessive levels of DPM before the problem is identified. Moreover, the delay involved in getting the loaded filter to the lab inevitably means the loss of some of the more volatile organic carbon. To remedy this delay, researchers from the National Institute for Occupational Safety and Health are seeking to develop a field-portable, real-time method for measuring elemental and organic carbons in DPM aerosols. In the current study, the use of mid-infrared spectrometry was investigated. It is believed that mid-infrared spectroscopy is more suitable for use in a real-time field-portable device than thermo-optical analysis methods. This article presents a method for measuring organic carbon (OC) and elemental carbon (EC) in DPM for a broad range of OC/EC ratios. The method has been successfully applied to laboratory-generated and mine samples.

By MAURICE SUNKPAL, Taghi Sherizadeh, ELAHEH TALEBI, PEDRAM ROGHANCHI

Excessive heat exposure is among the health and safety hazards for mine workers. The nature of the underground climate makes it a convenient avenue for heat generation and accumulation from several heat sources, including autocompression, equipment and heat from strata. This study investigates the effects of clothing insulation and acclimation on the thermal comfort of mine workers exposed to heat in underground working environments. Several clothing ensembles were considered to analyze the effect of the thermal resistance of clothing on the workers’ thermal comfort. To investigate the impact of clothing insulation, the thermal comfort limit of an underground miner was calculated in the form of maximum allowable exposure time for an eight-hour shift.

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

Manufacturers have improved various stirred mill types to be well adapted to fine and ultrafine grinding applications. These stirred mills, which are operated in wet or dry conditions, may be classified as horizontal — such as AHM-horizontal agitated media mill, IsaMill and Drais mill — or vertical — such as tower mill, Vertimill, Maxmill, Stirred Media Detritor and ATR vertical agitated media mill. The main difference between vertical and horizontal structures is in their operational variations. Additionally, the scaling-up of mills is also an important parameter for selecting the suitable orientation [1]. The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch-type stirred mill. The experimental results were evaluated using stress intensity analysis. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1 × 10−3 to 5 × 10−3 Nm at 750 and 1,500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value.

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

This study investigates the changes in seismic velocity of rockmass before and after three major seismic events to determine any potential identifiable precursory velocity changes associated with these events. Induced stress measurement is one of the challenging tasks in deep underground mining, with extreme impacts on the safety and stability of the mine. This study used p-wave passive seismic tomography to image the velocity redistribution within a rockmass, which can indicate induced stress level changes in the rockmass and detect the velocity changes that might precede a major seismic event or a rockburst. The ultimate goal of this research focus is to develop another tool for the deep-mining community that will help to increase safety and efficiency. For this purpose, the hypothesis of conventional mechanics, which implies induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs, is evaluated. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring; however, the p-wave velocity did increase in the closest “zone center” for two of the three events. 

By Kwangmin Kim, Taehee Lee, Minkyu Kim, JUNHYEOK PARK

Mine tailings storage facilities (TSFs) can be a significant source of fine, respirable dust. About 25 percent of the mass fraction of tailings from a hard-rock mine consists of particles of a respirable size (smaller than 10 μm) [1]. This dust poses concerns, especially for nearby communities, because of its detrimental impact on respiratory health. Respirable tailings dust, primarily composed of quartz or free silica (SiO2), may cause silicosis, chronic pulmonary disease, bronchitis, collagen vascular diseases, and chronic granulomatous infections [2]. 

By PETER ROBINSON, KEVIN BARBER, OLIVER WHATNALL

The investigation and uptake of filtered tailings continues to grow around the world, but cost and scalability are deterrents for mining companies. Filtration technology that is currently in use is unable to meet the needs of many operations and projects that would otherwise adopt filtered tailings. For tailings to reach the desired moisture content for dry stacking, the majority of processes require pressure filtration, with significant upfront and ongoing maintenance costs. Given the comparative lower costs associated with low-pressure Viper vacuum belt filtration, this technology has the potential to alleviate dependency on high-pressure applications and make efficient dewatering and handling of tailings a more economic and sustainable solution.