Search Documents

By R. L. Tobie, E. K. Staley

Because of high production demands at San Manuel mine (approximately 40,000 tpd) and the relatively narrow grade range of the orebody, no attempt is made by the company to mine selectively. The caving sequence is laid out to meet the production demands, and proceeds in a manner to induce the least amount of weight on extraction openings. Once an area is undercut, draw control procedures are applied uniformly until the area has been mined to depletion. The orebody, located 50 miles northeast of Tucsoil, Ariz., is a low-grade deposit of chalcopyrite disseminated throughout a structurally weak, highly fractured, strongly altered granitic host rock over- lain by several hundred feet of relatively competent andesitic conglomerate. When undercut, the granite ore caves readily into fragments which usually pass through the grizzly without either excessive breaking or an undue amount of secondary blasting.

Jan 6, 1967

By H. R. Spedden

As part of its broad program of educational assistance-including grants, fellowships, and scholarships -Kennecott Copper Corp. offers summer employment opportunities for college students at each of its operations. Originally, summer job programs were intended primarily to help students defray their educational expenses. But as the nation's economy expanded with increased production and a growing demand for well-trained engineers, summer employment became an important means to help qualify future professionals and fill industry's need for them. Both the employer and the student thus derive benefits from such training.

Jan 6, 1967

By A. T. Yu

From the very beginning when an ore body is blocked out, till the last ton of mineable ore is shipped to the smelter, consciously or not, a mining engineer is incessantly wrestling with the materials- handling problem. In the mine and the plants, over the haulage routes, and at the shipping terminals, his fundamental responsibility is to see that each ton of ore and/or waste is extracted, processed and moved easily and economically. Success or failure of many a mining enterprise often rests principally with the judicious and effective application of existant materials-handling technique or its innovation. Time and again, key innovations in practicing techniques have turned a losing venture into a successful and profitable one.

Jan 6, 1967

By M. J. Coolbaugh

Mining of potash more than 3000 ft beneath the water-bearing sediments in Saskatchewan presented the unique challenge of designing stable mine workings and assuring protection from overhead water in a material that was believed to flow plastically, but whose behavior as a plastic material was not sufficiently known. Under the stress conditions ordinarily encountered in mining most rocks behave as elastic materials; that is, they compress slightly under pressure, and rebound when the pressure is released. Salt and potash, however, are different. Even under the relatively low pressures encountered at shallow depths, these materials become slightly plastic and yield to stress by flowing.* The plastic properties become more pronounced at greater depth and pressure, and the question arises as to whether or not the plastic flow will be rapid enough and exert enough pressure to destroy underground structures or interrupt the mining process.

Jan 5, 1967

By A. J. Carlson, G. M. Marincel, M. L. Hovland, J. H. Healy

Research personnel of Erie Mining Co., a pioneer taconite mining firm on the Mesabi Range, have invented a new method to make an effective 325 mesh separation at high tonnage rates over stationary screens. The company regards this development as historically significant in that it represents the first successful method to commercially screen large tonnages of ore at fine sizes. Erie, which is now completing an expansion program at its plant site near Hoyt Lakes, Minn., has incorporated this screening method as part of that expansion. When completed, the concentration plant will produce 10.3 million tons of iron concentrate, all of which will have been efficiently screened at 325 mesh.

Jan 4, 1967

By G. Don Sullivan

Although the first application of strip mining dates back to 1866, the true origin of today's problem of land reclamation is found in World War II, when the yawning war machines demanded more, and faster fuel production. To meet the new wartime demands, the strip coal mining companies that had been producing coal for the normal needs of industry and commerce during peacetime worked to the full extent of their capacities but were unable to satisfy the voracious demand. To supplement the production of the established mining firms, a host of temporary, make-shift coal strip operations came into being-road contractors, ditchers and foundation excavators, earth movers of every type became strip coal operators. Unfortunately, many were of the here-today-gone-tomorrow category, and showed little concern for the condition of the land after mining. Likewise, the land owners of the mined properties (most of the land was on royalty lease or tonnage contract) showed little concern. Land owners realized from their acreages more income during the war years of coal production than could have been obtained in two or three lifetimes of conventional farming or other land uses. Most of these mined lands were sub-marginal with little productive promise. As a result the wartime stripping produced most of what are known today as "orphan banks" or "abandoned strip pits." It is of these that so much of the present day complaints about strip mine reclamation are being made.

Jan 3, 1967

By H. William Ahrenholz

The coal industry had another prosperous year in 1966. Since the turn of the decade, production has been climbing at an average rate of 6% per annum. Although the fast pace slackened somewhat, 1966 production showed a gain of almost 3 % over that of 1965. An impressive record can be drawn from the fact that output per man-day in 1966 was more than twice that of the early 1950's, and more than three times that of the early 1940's. And even though man-power requirements lessened, those men retained by the industry worked longer hours and benefited through higher hourly pay rates. However, cost to the customer increased a little. Such statements can only be made for a healthy industry -one that is constantly improving its efficiency. Coal currently provides more than 25% of the total U.S. energy output. About 50% of all U.S.- mined bituminous coal goes directly to the electric utility market. It should be noted that, now, well over one trillion kwh of electricity is generated annually. Dependence of the giant electric utility industry on coal is based on economy and an abundant, dependable supply of this fuel.

Jan 2, 1967

By Gill Montgomery

At this moment in the history of the world, the all- pervading and universally most important fact is that the world population is beginning to outgrow its food supply, and the United States has suddenly lost its ability to give away huge food surplus to any nation in the world with a food shortage problem. This, of course, means that, all of a sudden, our government must completely reverse its former bureaucratic stance regarding crop controls and agricultural price supports, to out-right incentives to increase farm production and bring more idle land into food-growing use.

Jan 2, 1967

By R. L. Mauger, P. E. Damon

Potassium-argon dating of the late Mesozoic and Cenozoic intermediate to acidic plutons and volcanic rocks of Arizona and northern Sonora demonstrates the existence of two distinct magmatic episodes. The earlier episode begins in late Campanian time and dies out before the middle Eocene. Following a quiescent period in middle and late Eocene time, magmatism increases in Oligocene time, becomes most intense at the Oligocene-Miocene boundary and dies out as the Pliocene is approached. Pliocene magmatism is primarily confined to extrusion of post-orogenic basalts. The late Mesozoic-early Cenozoic magmatic pulse is essentially confined within the limits of the classical Laramide orogeny (Laramie through Wasatch time). The mid-Tertiary pulse is contemporaneous with the mid-Tertiary Basin and Range orogeny. The Laramide provides an excellent specific example of Umbgrove's concept of the pulse of the earth and in general his concept appears to be meaningful. Copper porphyry mineralization is time-congruent with Laramide magmatism and there seems to be no doubt as to the existence of a genetic relationship between the two phenomena. Two origins are tenable: direct accumulation of the copper sulfides in the copper porphyry liquid magmatic environment; or, introduction of the mineral constituents entirely from a larger source magma when the host rock is already crystalline. Transgression and regression of the epicontinental seas provide an excellent indicator of orogeny and epeirogeny. There was an overall transgression of the epicontinental seas from early Triassic time through the Turonian epoch in early late-Cretaceous time. Thereafter, there is a relatively continuous regression of the seas until the present time. Both the earlier transgressive episode and the later retreat are intermpted by temporary but distinct reversals. These interruptions can be correlated with classical orogenies. There are six distinct orogenies so indicated in the Mesozoic-Cenozoic eras. These occur at approximately 35 to 40 m.y. intervals. The regression of the epicontinental seas following the Turonian epoch was contemporaneous with the deepening of the Pacific ocean basin over the Darwin Rise. As the Darwin Rise was collapsing the East Pacific Rise was being elevated. The Western United States, situated on the eastern flank of the East Pacific Rise, was upwarped and tilted toward the east. Epeirogeny is the primary consequence of processes that operate on a global scale. Orogeny is an exothennic process that is limited in space and is treated here as a secondary consequence of epeirogenic-initiated warping. The off-campus buildings of the University of Arizona Geochronology Laboratories rest on the volcanic rocks of Tumamoc Hill. From this hill, the observer may obtain a beautiful view of typical Basin and Range topography. The city of Tucson lies below, contained within the broad Santa Cruz basin and surrounded on all sides by characteristic NW-SE trending ranges towering as much as 7000 ft above the valley floor. Since the senior author arrived in Tucson eight years ago, a great deal more has been learned about the geochronology of this and neighboring basins and ranges. For example, the volcanic rocks underlying the laboratory at Tumamoc Hill were shown on the state geologic map as Quaternary basalt. A student of the senior author has demonstrated that the so-called basalts are in fact alkali-andesites (Halva, 1961), and we now know that these alkali-andesites or doreites (Mielke, 1965) are of early Miocene age rather than Quaternary age (Bikerman and Damon, 1965). Is it any wonder then that geologists disagree on the nature and time of Basin and Range volcanism, plutonism and tec-tonism? The plain fact is that few definitive Cenozoic fossil sites were available upon which to base a chronology and geologists were forced to guess the ages of rocks in order to achieve the semblance of a time classification. We have now made considerable progress in developing a K-Ar chronology for the volcanic and plutonic rocks of the Basin and Range (Bikerman, 1965; Damon and Bikerman, 1965; Damon et al, 1964 and 1965; Mauger et al, 1965). It is the purpose of this paper to point out the main features of this chronology and to discuss the relationship of magma-tism to orogeny-epeirogeny during post-Turonian time. We will also discuss probable relationships during

Jan 1, 1967

By Ernest A. Curth

The Bureau of Mines studied pressure changes in coal pillars by using encapsulated hydraulic pressure cells to measure relative changes in stress developed during mining. The data indicate that (1) abutment stresses were detected when the pillar line is within 42 to 100 feet, (2) vertical pressure increases as coal is mined in the pillars, (3) at first pressure is higher at the edge of the pillar than in the core, but as mining progresses, the higher pressure is measured in the core of the stump, and (4) in the two instances where lateral pressures were measured, they remained lower than the vertical pressures during pillar extraction. The data also indicate that the mean vertical pressure increase, 6P, in a pillar is roughly related to the percent of pillar extracted, A, by the empirical parabolic equation

Jan 1, 1967

By G. T. Hahn, C. N. Reid, A. Gilbert

An evaluation is made of the possible cautsal relationship between twinning and fracture in molybdenum. For both single and poly crystalline material no instance of twin-induced fracture was observed. Instead brittle fracture was found to be slip-induced at heterogeneities. For single-crystal material, the yield stvess in compression and the fracture stvess in tensiow obey a similar angular- relationship which follows approximately a 1/cos2 ? law. where 0 is the angle between the specimen axis and the nearest (100) plane. This sittlilarity between yield and fracture behavior casts doubt on the interpretations made previoltsly that a 1/cos2? relationship supports a critical normal fracture stress criterion. SINCE fracture in brittle materials takes place at stresses an order of magnitude lower than the theoretical strength of the lattice, it must be postulated that some stress-concentrating effect is operative during the fracture-initiation process. Several mechanisms have been proposed whereby the necessary stress concentrations could be produced. The well-known Cottrell mechanism1 describes a dislocation interaction which can lead to the formation of an incipient cleavage crack on a cleavage plane, and both zener2 and stroh3 have discussed models which predict the stress concentration at the intersection of a slip band with a grain boundary. When twinning occurs twin/twin intersections and twin/grain boundary intersections represent another possible means of fracture initiation. Although still controversial, the concept of twin-induced fracture is supported by a weighty mass of evidence, which has been reviewed in a recent paper.4 This investigation was conducted in order to assess the extent to which the brittleness of molybdenum can be ascribed to this cause. Emphasis was placed on seeking direct metallographic evidence for twin-induced fracture such as arrangements of twins located at the fracture origin. EXPERIMENTAL PROGRAM Materials. The experimental materials are described inTable I. From the chemical analyses and estimates of the amounts of interstitials likely to be retained in solution,5 it is concluded that all were mul-tiphased systems. X-ray diffraction experiments6 showed no evidence of preferred orientation in the polycrystalline materials. Single crystals were grown from Molybdenum X and Y using the floating-zone technique,' in a vacuum of better than 3 x 10-5 Torr. However difficulties were experienced with Molybdenum X due to violent gas evolution from the molten zone, and additional crystals (Crystals 3 to 6) were produced by annealing for 5 1/2 hr at 2300°C under a vacuum of 10-4 Torr. Techniques. A series of tension, compression, and bend tests was conducted. Tension tests were used to demonstrate brittle behavior, to measure brittle-fracture stresses, and to provide fractured specimens for metallographic inspection. Compression tests were employed in order to obtain some ductility and a measure of the yield stress. Furthermore, it was considered that compression loading would permit the study of crack nucleation in the absence of propagation. The bend tests were conducted to facilitate identification of the fracture origin, which would be expected to be at, or near, the tensile surface of the sample. Tests were carried out at temperatures between 78" and 298°K attained by means of a liquid-nitrogen evaporator of modified Wessel design.' Specimens were fashioned by mechanical grinding, and, prior to heat treatment, were electropolished at 10 v in a 3:l mixture of ethyl alcohol and sulfuric acid, using a stainless-steel cathode. Except where noted, a strain rate of 4 pct per min was used. All specimens had a gage section 0.75 in. long; diameters of 0.10 and 0.20 in. were adopted for the tension and compression specimens, respectively, the former of single shoulder design, the ends being gripped in split collets with a conical bearing surface. In the bend test, electropolished specimens measuring 0.080 by 0.25 by 1.25 in. were deformed at 78°K by four-point loading. The bending device had spans of 1 in. between the outer and 4 in between the inner fulcra; it was stressed between the compression anvils of the Instron machine at a constant deflection rate. EXPERIMENTAL RESULTS Polycrystals. Tension and Compression Tcsls. It is apparent from Fig. 1(a) that above 170°K fracture of Molybdenum X takes place at stresses equal to or greater than the compressive yield stress whereas

Jan 1, 1967

By William D. Klopp, Joseph R. Stephens

ThE phenomenon of high ductility associated with a phase transformation, termed super plasticity, has been reported for a number of alloy systems. Abnormally high ductility has been observed during tensile testing of cast eutectic alloys of Pb-Sn and Mg-cu.1 Brasses of Cu-37 at. pct Zn and Cu-40 at. pct Zn elongate up to 180 pct when tested near their transformation temperature.' Enhanced ductility was also observed in Cu-47 at. pct Zn tested near the order-disorder transformation temperature. The most remarkable super-plastic effect reported to date is for the eutectoid alloy A1-60 at. pct Zn, where elongations up to 1000 pct have been reported.3 underwood4 has recently summarized the conditions that normally accompany the superplastic effect which are: 1) a phase transformation or allotropic change or order-disorder transformation; 2) an externally applied stress; 3) presence of an interface between two phases; and 4) a metastable structural condition. In addition, higher ductility is observed when the specimen is tested at slow deformation rates rather than under impact. The purpose of this note is to present evidence of the superplastic effect in a Cr-30 at. pct Co alloy. In addition, low-temperature bend ductility data are given for the alloy in the quenched, metastable, single-phased condition and in the slow-cooled, two-phased, near-equilibrium condition. Sixty-gram alloy ingots were prepared by noncon-sumable arc melting of iodide chromium and electron-beam-melted cobalt. These were cast into rectangular ingots and fabricated to 0.035-in. sheet by rolling at 2300°F. Attempts to roll at slightly lower temperatures invariably resulted in severe cracking, apparently due to presence of the brittle a phase below the transformation temperature of 2230°F. Tensile specimens with a 0.25 by 1.0 in. reduced section were cut from the sheet by electrical discharge machining. The specimens were heated at 2400°F for 1/2 hr to obtain a recrystallized, bcc, single-phased structure. Temperature of the specimens was subsequently raised or lowered to the desired test temperature and held for 10 min prior to testing at a crosshead speed of 0.01 in. per min. Fig. 1 shows the chromium-rich side of the Cr-Co phase diagram.6 The alloy composition investigated is near the point of maximum solubility of cobalt in chromium, and the alloy is two-phased when in equilibrium at temperatures below 2230°F. The results of tensile tests conducted at temperatures indicated by X's in Fig. 1 are summarized in Figs. 2, 3, and 4. Tensile elongations shown in Fig. 2 increase from 11 pct at 1900°F to a maximum of 160 pct at 2250°F. The elongation then decreases to 44 pct as the test temperature is further increased to 2600°F. The proximity of the temperature of highest elongation and the solvus temperature suggests that a superplastic effect is present in Cr + 30 at. pct Co similar to that observed for other alloys that show anomalous ductility. The variation of upper yield stress with temperature is shown in Fig. 3. A small peak in yield stress occurs at 2250"F, coincident with the maximum in

Jan 1, 1967

By James A. Wasson

This report analyzes the petroleum-production potential of the basal Greenbrier dolomite zone, Sycamore-Millstone field, Sherman District, Calhoun County, W. Va., through the application of certain secondary-recovery methods. The well logs obtained and the core recovered from a well in this formation permitted an evaluation of the productive capability of the reservoir, Approximately 120,000 stb of oil may be produced from a 20-acre five-spot unit at breakthrough if the property is waterflooded. At an assumed limiting producing gas-oil ratio of 20)000 sef/stb, approximately 69,000 stb of oil should be recovered by low-pressure gas drive.

Jan 1, 1967

By J. M. Singer

This study was undertaken to obtain some fundamental information about hazardous mixtures of coal dust and methane (firedamp) likely to occur in mines. Fuel concentration limits for ignition of mixtures of coal dust, methane, and air have been determined by a hot-gas ignition method. The limiting concentration of each of the two fuels was usually less than that corresponding to its lean flammability limit in air. The lean limits of flammability of coal dust vary with the type and size of the dust; in this study coal dust concentrations were less than 80 mg/liter. Ignition jets were turbulent pulses (emerging from a channel of 0.5 cm diam) resulting from explosions of stoichiometric mixtures of methane, oxygen, and nitrogen, Temperatures of the ignition jets were varied by changing the oxygen index (OI) = O2/(02 + Nj2) of the primary methane-oxygen-nitrogen mixture (adiabatic flame temperatures from 2,000° to 3,000° K). The objectives of the study were to establish quantitative relations between concentrations of each fuel at ignition limits of hybrid mixtures and to study the mechanism of ignition of these hybrid mixtures by hot turbulent gases, Empirical equations were fitted to concentrations for four coals, namely) Pittsburgh Seam (sizes A, B, and C), Sewell No.2 Seam, pocahontas No.3 Seam, and anthracite. Equivalences of coal dust to methane were computed from these equations; equivalence being defined as -Ac/Am, where c is the coal dust concentration and m is the methane concentration, each in milligrams per liter of air. It was found that the equivalence increases as the temperature of the hot-gas jet decreases. In general, the equivalence is also an inverse function of volatile content of the coal and a direct function of the particle size, However, volatile con-tent in itself is not a sufficient correlating variable, nor is the specific surface area of the coal dust.

Jan 1, 1967

By P. Datta, L. L. Handy

For a wetting phase displacing a nonwetting phase from a porous medium the distribution of the residual fluid may depend on displacement conditions. Although this subject has been debated in the literature, only a few experiments have been cited to support the various conclusions. Experimental results presented in this paper show that fluid distributions are dependent on imbibition pmcedures. Results agree qualitatively with predictions from the pore doublet model. If the rate of water imbibition is restricted, the nonwetting phase is trapped preferentially in .the larger pores as expected. But if the rate of water imbibition is unrestricted, trapping occurs somewhat more in the smaller pores. These conclusions were deduced primarily from relative permeability measurements. INTRODUCTION Relative permeabilities are known to depend on the saturation history of the porous medium. For either continuously increasing or continuously decreasing wetting phase saturations, however, they have normally been assumed to be single-valued functions of saturation. Severat investigators have compared relative permeabilities measured by different methods and have reported acceptable agreement.1-5 Studies of simple models of the displacement process suggest that the distribution of residual fluids can be influenced by the displacement method. If this is so, relative permeabilities also should depend on the method of displacement. These predictions have not been supported by experimental data. The object of this paper is to investigate experimentally some of the predictions of these model studies. The particular question of importance is whether steady-state and unsteady-state methods should be expected to give the same values of relative permeability. Much of the reported data showing agreement between steady-state and unsteady-state methods have been obtained on un consolidated sand. Johnson, Bossler and Naumann, however, compared steady-state and unsteady-state results for Weiler sandstone and found no significant differences.5 Levine made a detailed study of pressure and saturation distributions for a laboratory waterflood in a consolidated system but made no attempt to calculate performance from steady-state relative permeability data Bail and Marsden in a somewhat similar set of experiments did attempt a comparison of observations with predictions but the results were inconclusive.7 Excluding gravity, two forces affect the distribution of wetting and nonwetting phases during an unsteady-state, immiscible displacement: viscous and capillary forces. If relative permeabilities are indeed the same when measured by steady- or unsteady-state methods, the fluid distributions at the same fluid saturations must be similar for both methods. Furthermore, the implication is that the relation between capillary and viscous forces is the same for both methods insofar as the effect on microscopic fluid distributions is concerned. Unsteady-state displacements are normally run at high rates to maximize the ratio of the viscous to capillary forces. The objective is to reduce the effect of capillary forces on macroscopic fluid distributions. For floods in which the phase which wets the porous medium displaces the nonwetting phase, capillary forces compete with viscous forces in determining fluid distributions.8 The residual nonwetting phase is discontinuous. Competitive aspects of viscous and capillary forces and the resulting effect on water-oil distribution in porous media have been illustrated in an elementary way using a pore doublet model. This model and predictions from it have been discussed at considerable length by Rose and Witherspoon, Rose and Cleary and by Moore and Slobod.9-13 Rose and Witherspoon show that so long as water invades the model at a rate equal to or greater than the free imbibition rate, the water will move through the larger capillary of a doublet first and trap oil in the smaller capillary. On the other hand, if a negative pressure is applied to the water

Jan 1, 1967

By F. X. Tartaron

Behavior of hard-burned quicklime was compared with that of soft-burned quicklime in an oxygen converter utilizing oxygen blowing in a rotating cylindrical vessel, set at a 30° to 60° angle to the horizontal and operated at a predetermined speed of rotation. Four pairs of tests were made) each comparing hard lime with soft lime. Three of the pairs differed from one another in the quantity of lime employed) and the fourth differed in blowing time, All four pairs showed an increase in yield when soft lime was used. Three of the pairs revealed that the ratio of the oxygen consumed with soft lime to the oxygen consumed with hard lime was the same as the ratio of metal yield with soft lime to the metal yield with hard lime. The fourth pair contained an error and could not be included. Finally, a close inverse relation was found between the combined iron in the slag and the combined lime in the slag, which can be expressed by the equation pct Fe = 52.67 -0,906 (pct CaO).

Jan 1, 1967

By George A. Colligan, John M. Lo

Electrical resistivity as a function of temperature was investigated in undercooled gallium and under-cooled Ga-In alloy of eutectic compositian to examine structural changes in undercooled melts. A continuous linear extension of the resistivity was determined for 99.999 pct pure gallium when undercooled below the stable Ga(l)-liquid, and the metastable Gafl)-liquid equilibria. In icndercooled Ga-In, a significant continuous negative departure from linear resistivity behavior was observed below the eutectic temperature. All resistivity measurements were made by the four-point probe technique. ThE temperature range for investigations into the physical properties of liquids before freezing has been greatly extended with the undercooling of massive melts of pure metals and alloys. Experimental determinations of thermal and transport properties and diffraction patterns in undercooled systems should throw further light on the structural behavior of liquids. Many measurements showing prefreezing anomalies in viscosity1'5 have been regarded677 as evidence for structural groupings in the liquid state. However, the majority of viscosity results,~)~-~~ conforming to the law 17 =A exp(~/RT), do not support theories of atomic aggregation. For the system Cd-Sb, which exhibits a metastable solid phase, Fisher and Phillipsg reported that, in undercooled alloys, the activation energies for viscous flow below the stable liquidus are much higher than those above it. Similarly, Miller et a1." observed a doubling of the activation energies for electrical conductivity in undercooled Cd-ib alloys. These effects were suggested as indicative of atomic association and clustering in the liquids at lower temperatures. With the recent establishment of metastable phases in pure gallium22 and its alloys,23 attempts were made during this investigation to undercool bulk samples and to determine the temperature dependence of electrical resistivitv. Pure gallium, when undercooled below -17°C at atmospheric pressure, can crystallize to either a stable Ga(1) phase (mp, 29.78"C) or a metastable phase identi-

Jan 1, 1967

By A. Z. Dimitroff

Immediate detection of methane buildup or of sudden liberation of large quantities of methane in the face area is essential to avert disasters in coal mines. Proper timely detection and handling of methane have always presented problems in extremely gassy mines, and these problems have been magnified by present accelerated mining methods. Strict rules and regulations have been established by coal-mining companies, States, and the Federal Government, which provide for periodic inspections for methane in face areas when electrical equipment is working. Other provisions require the operator' to shut down electrical face equipment and change or adjust ventilation when more than 1.0 percent of methane is detected. Nevertheless, human failure to detect such conditions has been responsible for numerous ignitions arid explosions Recognizing this fact, Marling J. Ankeny, former Director of the Bureau of Mines, proposed in 1958 the development of an automatic methane-monitoring device. He envisioned such a device as being entirely dependable, capable of giving a warning when a predetermined concentration of methane in air is reached, and capable of deenergizing the equipment and rendering it inoperative when a dangerous concentration of methane is present in the air. Such a device has been developed by the Bureau of Mines Health and Safety Research and Testing Center in Pittsburgh, Pa.

Jan 1, 1967

By George A. Komadina

Pima Mining Company has recently completed their expansion tripling the plant capacity to 18,000 tons per day and now is in the process off expanding to 30,000 tons per day with completion scheduled for the summer of 1967. This paper briefly discusses the additions to the mining department and support areas with a more detailed report on the complete new crushing plant and additions to the concentrator. The crushing plant includes a 54-inch gyratory crusher, three 7-foot standard and seven 7-foot short head crushers along with necessary screens, feeders, and conveyor belts to produce a minus 1/2-inch rod mill feed. The concentrator consists of ten milling sections, each containing one 10-foot by 16-foot rod and two 10.5-foot by 13-foot ball mills, classification is done with cyclones. Pulp from each section is floated in 50 cells of 66-inch Fagergren flotation machines to produce a rougher concentrate which is cleaned in six stages of Denver cleaners to produce a final concentrate The various mill products are thickened with disposal made in conventional manner. Plant instrumentation is discussed in the paper.

Jan 1, 1967

By Jack L. Henry

The monocarbide region of the ternary system U-C-O has been investigated at 1,700° C as the first phase of a more extensive study of a portion of the four-component system U-C-O-N. An area bounded by the following compositional limits in atomic percent was studied: U, 44 to 55; C, 30 to 60; 0, 0.2 to 20. Compacts composed of mixtures of uranium, graphite, and uranium dioxide powders were sintered at 1,700° C under an equilibrium pressure of carbon monoxide to produce uranium oxycarbide specimens having a variety of compositions. Sintered specimens were evaluated by X-ray, chemical analysis, and ceramographic techniques. Solid-solution boundaries and phase relations have been established, and the effects of composition on the lattice parameter as well as the decomposition pressure have been investigated. Oxygen can be substituted for carbon in stoichiometric uranium monocarbide to the extent of about 17 atomic percent at 1,700° C. The composition range of the oxycarbide solid solution extends from about 48 to 51 atomic percent uranium in the low oxygen region. Above 10 atomic percent oxygen the composition range narrows to less than 1 atomic percent uranium. Carbon monoxide exists as a gaseous phase in equilibrium with all compositions which contain oxygen. Five separate phase fields were found bounding the solid-solution area. Other phases within this portion of the system include uranium, uranium dioxide, uranium dicarbide, and uranium sesquicarbide. Decomposition pressures of oxycarbide compositions at 1,700° C have been found to vary from a few microns for stoichiometric and uranium-rich compositions to 35 torr for carbon-oxygen-rich specimens. Lattice parameters were found to depend upon the U to C + 0 ratio as well upon the extent of substitution of oxygen into the stoichiometric monocarbide lattice.

Jan 1, 1967