Search Documents

By J. O. Brittain, E. P. Lautenschlager, F. Felberbauer

This investigation was undertaken to evaluate the effect of a dispersed phase in a iron upon the strain hardening and the stress dependency of dislocation velocity as inferred from the strain-rate sensitivitv. Experiments were made in a-iron specimens with controlled amounts of carbon and/or A12O3. They were tested at various temperatures between 195' and 373 'K under a variety of conditions oj-concentration, strain rate, and quench aging. The resulting yield strength, flow strength, and strain hardening increased with addition of Al2O3. The parameter m, measured from changes in strain rate, was xsed to describe the stress dependency of the dislocation velocity. m was found to increase with additions of A12O3, increasing carbon in solution, and with increasing temperature. When applied to a recent model for yielding based upon dislocation multiplication and velocity characteristics, the values of m alone did not successfully predict yielding for the materials of this investigalion, but had to be adjusted with a consideration of the number of unlocked dislocations nucleated heterogeneously at discontinuities or inclusions. The change of yield strength with Al2O3 Interpar-ticle spacing appeared to obey a theory of Orowan. EVER since the concept of dislocations has been introduced to explain plastic deformation in crystalline materials, the origin of dislocations and the source of the number of dislocations required to account for plastic deformation have been persistent questions. Ruling out the possibility of homogeneous nucleation,' Gilman2 drew attention to the various cases of heterogeneous nucleation as the source of dislocations, whereas Frank and Read3 introduced the Frank-Read source. However, Gil-man found that the Frank-Read sources did not play a dominant role in the deformation of LiF crystals, but that small precipitates are often, if not always, associated with the nucleation of dislocations. In LiF crystals, however, most of the dislocations arose through the multiplication of moving dislocations in a mechanism described by Koehler4 and Orowan,5 Thus, relatively few precipitates could account for a large number of dislocations. A similar observation of dislocation nucleation at inclusions of precipitates was made by Stein and LOW' on Si-Fe crystals. Their crystals contained

Jan 1, 1964

By C. H. Ma, J. S. Makris

This paper describes a modified X-ray diffraction microscope wzethod based on the general principles of Berg-Bawett's Method, Lang's Method, and Woosters1 Technique. This new method may be used for stationary or oscillatory photomacrographs, with both reflection and transmission techniques. In the stationary technique, a small point-source of a divergent X-ray beam of white radiation is used; in the oscillatory technique, a monochromatic divergent beam is employed. The chief advantages of the method described herein are that only approximate alignment of the Bragg angle -of-interest is needed during exposure, and that a large portion of a crystal-specimen surface can he irradiated. In recent years, the study of dislocations through X-ray diffraction microscope techniques has received considerable attention as concerns the per,fection of single crystals. Very promising results have appeared in the literature.'-' These techniques are very useful when the dislocation density of a crystal is near 105 per sq cm or lower. The principle of X-ray diffraction microscopy is based on the differential effect of X-ray primary extinction between the distorted parts and the perfect parts of a crystal. When an X-ray beam impinges on a set of planes of a crystal at the correct Bragg angle, diffraction of X-rays will occur with a 90-deg phase shift of the diffracted beam. This once-diffracted beam still forms the correct Bragg angle with the planes ahead of it, if the planes are not distorted. Thus, part of the strength of the once-diffracted beam is rediffracted and the beam continues to travel in the direction of the primary X-ray beam. This twice-diffracted beam not only takes away part of the strength of the once-diffracted beam, but also causes destructive interference with the primary beam because it now is exactly 180 deg out of phase with the primary beam. As the primary beam goes farther and farther into the crystal, its intensity is continuously weakened. Asa result, the ultimate X-ray diffraction power of a set of undistorted planes is largely extinguished. This phenomenon is called primary extinction.1,2'4 If the set of planes ahead of it is distorted, the once-diffracted beam will have less chance to be rediffracted, because it could not meet the exactly correct Bragg angle for rediffraction. If a part of the beam does rediffract, this twice-diffracted beam is not exactly 180 deg out of phase with the primary beam, and thus it causes less destructive interference. As a result, the registered X-ray diffraction power of the distorted part of a crystal appears stronger than that of the perfect part. Thus, point-by-point contrast of a diffraction image is theoretically possible from a crystal containing dislocations. Two most popular X-ray diffraction microscope techniques today are Berg-Barrett's Method and Lang's Method. Both of these techniques require a

Jan 1, 1964

By I. R. Kramer

The apparent activation energy, U, JOY plastic deformation of aluminium, copper, and gold single crystals and polycrystalline aluminum was found to he dependent upon surface condition. At low strains, the value for U for aluminum single crystals was 4200 cal per mole ; however, this value decreased to 920 cal per mole when the specimens were polished during the test at a rate of 50 X 10-5 win-1 The activated volume also was found to increase with the rate of metal removal. That the surface plays an important role in plastic-deformation processes has been adequately demonstrated.1-4 Of particular interest at this time are the observations4 that the creep rate of single crystals of fee metals is increased markedly when specimens are polished during the deformation process. These observations were interpreted in terms of a dislocation debris layer at the surface regions of the crystal. This layer, which appears to be a region containing a high concentration of dislocations or segments of dislocations, not only will impede the egress of dislocations on the primary slip system, but will also provide a barrier against which dislocations may pile up. By this means, a stress which opposes the motion of dislocations will be generated. It is considered that this stress must be taken into account in any theory which describes the plastic-deformation process. Although a detailed dislocation model cannot be given at this time, it may be stated that the stresses opposing the motion of dislocations arise from the dislocations in the debris layer, Ts, and ti due to the resistance to motion imposed by internal obstacles such as Lomer-Cottrell barriers, subgrain and grain boundaries, forest dislocations, and so forth, as well as the resistance due to the presence of jogs on dislocations and the interaction of the stress fields of dislocations, and so forth. In essence, we have added an additional term, ts, to the usual form of the equation T = Ta- Tb, where Tb is the back stress due to the various types of obstacles which impede the motion of dislocation. Accordingly, the net stress, t, acting on a dislocation may be written as where Ta is the applied shear stress. For deformation which occurs by a thermally activated process5,8 ?=Ae-u/kT = A e(u,-VT)/kT [2] and U = Uo- Vt PI where U = activation energy for plastic flow, y = shear strain rate, Uo = activated energy for plastic deformation in the absence of stress and depends upon the particular deformation process, V = activated volume, k = Boltzmann constant, T = temperature, OK, and A = frequency factor. From Eqs. [I] and [3], U = Uo- V(Ta - Ti - TS) [4] and it is seen that if Ts decreases, the activation energy, U, must decrease if V remains constant. However, as will be shown, V is a function of the surface conditions. In their work on aluminum, Lytton and coworkers7 reported that at low strains the activation energy was 3400 cal per mole and at high strains it was 28,000 cal per mole. The lower value was interpreted in terms of the energy necessary to overcome the Peierls force, while the higher value was associated with the energy necessary for dislocations to move by a cross-slip process. It will be shown that the lower activation energy is associated with the surface debris layer rather than with the Peierls force. EXPERIMENTAL PROCEDURE Single crystals having a nominal cross section of 1/8 in. and a 3-in. gage length were prepared by a modified Bridgman technique using a multiple-cavity graphite mold. The initial purity of the metals was 99.997, 99.999, and 99.999 pet for aluminum, copper, and gold, respectively. The orientation of the specimens is given in Fig. 1. The measurement of the activation energy as a

Jan 1, 1964

By R. Wild, F. A. Wright

When a blast furnace has a certain defined burden and is operated under fixed conditions of blast temperature, etc., the fuel efficiency is determined by the extent to which the reducing gases can remove oxygen from the burden in the furnace stack. This is determined by two distinct factors: 1) The uniformity of gas-solid contact, and 2) The ease with which oxygen can be removed from individual pieces of burden. This latter is often called burden reducibility. When burdens were poorly prepared the first factor was by far the most important and a study of the reducibility of individual lumps was of rather academic interest. In recent years good burden preparation with emphasis on uniformly sized material has led to greatly improved gas distribution in the stack, and thus the second factor has become much more important and there has been a marked increase in interest in methods of measuring reducibility. This paper explores the Linder method of measuring such reducibility. The measurement of reducibility of burden materials must be carried out under conditions duplicating, as nearly as possible, those of the blast furnace stack. This is very difficult since the blast furnace process is a counter-current one, and thus the initial conditions encountered by the solid (gas temperature, composition, etc.) are the result of heat and mass transfer occurring lower down the stack. Any method of burden testing which does not take this into account is, at least to some extent, based on arbitrary assumptions. In an attempt to study blast furnace reactions under non-arbitrary conditions BISRA adopted the SCICE technique as a method of investigation. This technique has been used with a measure of success.' The SCICE technique, however, was found to be too slow for use as a routine test for burden materials and it was decided to construct additional equipment for burden testing. A test was required which would: 1) Be as realistic as possible. 2) Be quick and easy to operate. 3) Give some indication of the breakdown likely to take place during reduction in addition to a reducibility index. After a critical assessment of the reducibility tests which have been proposed it was decided to adopt the Linder test equipment and procedure as a basis for burden testing. THE LINDER TEST APPARATUS AND PROCEDURE The apparatus which was constructed (Fig. 1) was the same as that described by Linder2 except for minor changes in design. Linder also laid down a test procedure which he had derived from the results of investigations on Swedish blast furnaces. The variations of temperature and gas composition during the test were defined; these are shown diagram-matically in Fig. 2. BISRA's intention was to use the standard temperature and gas composition programmes for testing a variety of burden materials and also to investigate the influence of different programmes on standard burden materials, making use of information from the SCICE apparatus wherever this is possible. Up to the present, effort has been concentrated on the first part of the programme, and work on the second part has only just commenced. For each test 200 g of coke and 500 g of burden material were used. Linder had recommended that the coke and burden material should be between 1 and 1 1/2 in. and this was adhered to in early experiments on ores and sinters. Since the eventual aim of this work was to relate the test results to blast furnace operation, it was decided to carry out subsequent experiments using burden material in the size range used in the blast furnace, as far as this was possible. If the main interest was, for example, a comparison of the products resulting from different methods of agglomeration, then there would be advantages in using burden materials as close as possible to a standard size. After the charge had been placed in the reaction tube and this had been connected to the gas supply, rotation of the reaction tube at 30 rpm was started and the reduction programme was commenced, the gas temperature and composition being manually controlled according to the programme shown in Fig. 2. After the reduction test the charge was cooled in a nitrogen atmosphere. It was then removed from the reaction tube, the coke and burden separated, and the extent of burden breakdown assessed by screening it at 10 and 30 mesh. The extent of reduction was then

Jan 1, 1964

By Walter Kawa

Bureau of Mines research on the hydrogenation of coal has been concerned with developing processes that could be used to supplement the Nation's petroleum and natural gas resources. Motor fuel was produced in a subsidized coal hydrogenation industry in Europe prior to 1945, but the process used is still not economical and other methods of producing liquid and gaseous fuels from coal are being investigated. As an aid to the planning of coal hydrogenation research, a literature survey was made of processes or methods of hydrogenating coal that differ from the subsidized or conventional process. This report contains a bibliography of unconventional methods of hydrogenating coal and a brief discussion of the economics of the conventional method. A general discussion of unconventional methods is included, and the advantages and disadvantages are pointed out where possible. The survey supplements a previous Bureau of Mines survey3 and a comprehensive review published in 1930.4

Jan 1, 1964

By B. S. Graves

Deep well disposal of selected industrial wastes has been proved feasible and acceptable in the New Orleans area by several industries including Shell Oil Company's Norco Refinery and Chemical Plant where three of the six successful disposal wells in this area are operating. Well design and procedures for restoration of capacity are based, in most cases, on the principles of brine injection developed by oil producers in South Louisiana. Geological formations in the Gulf Coast area are suited to this type of injection because receiving strata are porous, isolated from sources of potable water and their water is compatible with the liquid wastes to be injected. This method of disposal is a simple, complete and economical solution to the problems presented by certain hard to treat wastes.

Jan 1, 1964

By Charles R. Boardman

Recent underground nuclear tests in tuff, alluvium, salt, and granite have yielded data essential to the evaluation of mining applications of contained nuclear detonations. The data indicate that for these media the cavity radius is predictable within ±20% without regard to the properties of the rock in the immediate shot environment. Properties of the chimney of broken rock resulting from collapse of the cavity, on the other hand, are found to be related to the properties of the rock and its preshot structural weaknesses. Seismic effects and radioactivity distribution are sufficiently documented to serve as a basis for predicting the safety conditions associated with detonations for a variety of yields.

Jan 1, 1964

Cominco began investigations about ten years ago relative to noise abatement in underground operations. As a result of intensive research, this study has advanced so that the practice now has wide application. Automotive mufflers are used on vane-type blasthole diamond drills. Exhaust hoses are attached to longhole percussion drills. Hand-held drills, such as airlegs and stopers, are equipped with mufflers which are either part of the drill, as received from the manufacturer, or are light rubber de-vices developed, fabricated and installed by Cominco. Ear defenders are in general use. The paper reviews details of practices employed, and assesses the success achieved. Noise is generally associated with some of the basic equipment used in mining. About ten years ago, in order to improve on this situation. The Consolidated Mining and Smelting Company of Canada Limited began investigations relative to noise abatement in its underground operations. As a result of intensive research, this study has advanced to the point

Jan 1, 1964

By H. L. Lovell

The growing production of fly ash with the many attendant problems of economics, disposal and potential uses suggests an urgent need to consider those properties which are basic in its beneficiation. Fly ash is extremely variable and heterogeneous in all respects except its fine size. Because of its production in huge quantities, it becomes significant as a potential raw material. Detailed data are presented describing particle size and shape, density distribution and magnetic characteristics. The major components include combustible residuals, magnetite and silicates. These data are discussed in terms of beneficiation processes and uses, The results of air classification to produce a uniformly fine-sized low combustible product are encouraging. It is proposed that major increases in the future use of fly ash, must involve some form of beneficiation. Both the coal producing industries and the consuming utilities would benefit from increased utilization.

Jan 1, 1964

By R. S. Kinasevich, D. D. Crabtree, D. W. Fuerstenau, T. P. Meloy, A. L. Mular

This paper presents details of the concept that size reduction in comminution machines takes place by three mechanisms; namely impact, abrasion, and chipping grinding. Experimental evidence is presented to show that each of these comminution mechanisms produces particles of a characteristic size distribution. The actual product from a comminution device has been postulated to be the result of a composite of these three types of mechanisms. Composite curves are demonstrated for a material following the Gaudin-Schuhmann, Gaudin-Meloy, and Rosin-Rammler size distributions. About forty years ago, Gaudin1 showed that grinding may be considered a combination of impact and attrition. Since that time, major efforts have been devoted to studies, both experimental and theoretical, of impact and compression fracture, while attrition has been almost wholly neglected, at least quantitatively. A significant attempt to distinguish between attrition and impact grinding is the work of Tanaka2 in Japan. By means of an instrumented abrasion grinder and a drop weight device, he determined coefficients relating the increase in surface area of various materials to the energy expended by the two methods of comminution. He showed that physical properties of a material determine its response to attrition and impact grinding. By extending his ideas to ball milling, he concluded that to a large extent the basic comminution process in a ball mill is due to the impact of falling media. Because Tanaka used a mass of particles in his drop weight device, however, he did not obtain pure impact size reduction. The purpose of this paper is to define basic mechanisms of size reduction, to verify that each has a characteristic and meaningful distribution curve, and to show how a combination of these mechanisms results in a size distribution very like that produced by grinding mills. DEFINITION OF COMMINUTION MECHANISMS The product from a grinding device will be considered to be the sum of the contributions resulting from the action of three basic mechanisms of size reduction which operate in a ball and rod mill. These are impact grinding and two forms of attrition, namely abrasion grinding and chipping grinding. Each is defined below. Impact Grinding: If a straight line is obtained when the cumulative weight fraction finer than a given size is plotted on log-log paper as a function of that size, the slope of the line is defined as the distribution modulus. A number of investigators 3,4,5 have shown that impact fracture of single specimens of different composition and shape results in a distribution of daughter particles that exhibit a distribution modulus of unity. This has also been true for materials broken in slow compression. Moreover, under slow compression or impact fracture conditions, theoretical distribution equations6*' which approximate the Gaudin-Schuhmann distribution when the distribution modulus is close to unity agree reasonably well with the experimentally obtained products. If one now considers a comminution process where many impact or compression fracture events are taking place, then any rational summation of the individual events yields, in the finer size range, a Gaudin-Schuhmann distribution whose distribution modulus is also unity. If the size distribution of the product from a mill has a distribution modulus of unity, it is implied that particles are fractured in a manner which results in a comminution event having a distribution like that obtained for the breakage of single specimens. These impact events would occur when a particle is smashed between balls or between a ball and the mill liner. Attrition, on the other hand, is that form of grinding which cannot be called impact grinding, and comprises both abrasion and chipping grinding. Abrasion Grinding: Abrasion is a form of surface wear resulting when particles rub against each other or against balls or the mill liner of a tumbling mill, somewhat like a piece of wood being rubbed over a piece of sandpaper. The surface wears at a more or

Jan 1, 1964

By C. A. Hollingsworth

The Deep Leg Flotation Cell was developed to solve a problem which confronted the Smith-Douglass Company on moving from one mining area to another. Poor recovery and, to some extent, inferior concentrate grade were encountered in the silica flota¬tion circuit. This was believed due to the softness of the phosphate which caused it to form slime. In view of the urgency of the matter, the problem was attacked from two angles. The first involved the development of a flotation cell which would not create slime and the second, a new or improved reagent for floating silica from phosphate rock which would be less sensitive to slime than reagents currently in use.

Jan 1, 1964

By Evan Adams

The Ireland Mine is located some seven miles South of Moundsville West Virginia, along the bank of the Ohio River. We are mining the Pittsburgh #8 seam. This seam is approximately 60" in thickness, and is immediately overlain by some 10 feet of a conglommerate material. The roof is difficult to control, due to the fact that it frequently is composed of substances not hard enough to be held together with 6-foot roof bolts. In many cases, we must use 10-foot roof bolts, in order to get bolt anchorage in the limestone above the conglommerate. Due to the elasticity of the limestone and its tendency to bend rather than to break, we have been unable to maintain a pillar line. Thus, we have found it necessary to mine by the room and pillar system. Belt haulage is used on room entries to automatic loading stations, thence into 15-ton mine cars, controlled at the loading point by car spotters. The maximum belt length is 2,000 feet. Rail haulage to the slope-bottom dump is by 27- and 50-ton locomotives. The mine produces coal two shifts per day, with 7 production crews on each shift. Mine and machinery maintenance is performed on the Midnight shift. We handle an average of 660 tons per machine shift.

Jan 1, 1964

By D. A. Kraai, S. Floreen

The effect of 1 to 50 ppm S on the ductility of nickel at 800° to 1400°F was studied. Results at each temperature showed a decrease in the reduction of area from approximately 95 to 5 pet over the sulfur range studied. Ductility varied with grain size, but only to a minor extent relative to the sulfiw effect. The effects of sulfur were completely offset by the addition of small amounts of magnesium. The results indicate that the "hot-short" loss in ductility is not an inherent property of nickel. Some possible mechanisms which cause the loss in ductility are described. MANY metals or alloys that normally possess high ductility exhibit a ductility loss at intermediate temperatures. This loss in ductility is often called "hot-shortness". Numerous examples of this phenomenon have been reported in the literature. Much of this work has been reviewed by McLean1 and by Rhines and Wray.2 To date there is no fully satisfactory explanation of the cause of this intermediate-temperature hot-shortness. It is generally recognized that impurities, and particularly impurities that form low-melting phases, can cause embrittlement. Examples of hot-shortness have been reported, however, where there were no obvious impurities present which would lower the ductility. Thus there has been some basis for believing that hot-shortness is an inherent property, and that even the purest metal would display a hot-short loss in ductility. This latter hypothesis was recently put forward by Rhines and wray2 based on studies of nickel and nickel alloys. In the discussion of this paper, however, Guard noted that high-purity nickel showed no hot-shortness.3 Thus there is reason to doubt whether pure nickel, or by inference any other pure metal, will inherently exhibit hot-shortness. The present work was initiated to determine the extent to which hot ductility was sensitive to very small amounts of an impurity element. If it could be demonstrated that hot-shortness could be induced by only minor amounts of an impurity, then it might be argued that hot-shortness in general is an impurity effect, and not a fundamental property of pure metals. The particular impurity studied was sulfur in nickel. The deleterious effects of sulfur are well- known. It is also well-known, and will be shown below, that additions of magnesium will render sulfur innocuous. When no such refining agents are added, however, the Ni-S system is a very useful one for studying the influence of small amounts of impurities. EXPERIMENTAL PROCEDURE Two heats containing -24 ppm S were vacuum-melted and small amounts of magnesium were then added under an argon atmosphere. These alloys were used to show the effectiveness of the normal magnesium treatment in overcoming the influence of sulfur. A second series of alloys with a sulfur range of 1 to 50 ppm was then prepared by vacuum melting nickel in alumina crucibles. No elements, such as magnesium, which tend to combine with sulfur were added. The higher sulfur contents were attained by adding nickel sulfide. Lower sulfur contents were prepared using a method in which the melt was oxidized under vacuum to produce the reaction S + 2O = SO2 These heats were subsequently deoxidized with carbon. Ten- to twenty-pound ingots were cast of all of the alloys studied. The compositions are given in Table I. The ingots were forged and hot-rolled to 3/4-in. bar. They were then annealed at either 2000" or 1600°F to produce different grain sizes. One-quarter-in.-diam tensile specimens were machined from the bars. These were tested at 800°, 1000o, 1200°, and 1400°F. The specimens were held at temperature approximately 45 min before testing. The strain rates were 0.005 min-1 to yielding, and 0.05 min-' after yielding. No extensometers or gage marks were placed on the specimens because the higher sulfur heats tended to fracture at the knife-edge indentations or gage marks. The properties measured were ultimate tensile strength and reduction of area. The analytical technique for determining sulfur at low levels was that developed by Burke and Davis.4 They reported a standard deviation of 1 ppm at an average sulfur level of 4 ppm in NBS standards. A standard deviation of 3 ppm is probably more realistic for the alloys used in this investigation considering the possibility of some segregation in the ingots. RESULTS A summary of the tensile results is given in Table I. As shown in the table, both heats to which

Jan 1, 1964

This paper outlines the position and capabilities of Western Canada's bituminous coal industry, and indicates the increasing importance of Japan as an export market. The use of coal in Japan is reviewed, especially as regards future trends, and an appraisal is made of Canadian coal in comparison with domestic Japanese coal and imports from other countries. The importance of maintaining a solid nucleous within the Canadian bituminous coal industry is emphasized. I N RECENT years, Japan has emerged as a valuable market for Canadian exports. The first major product exported in volume to Japan was wheat, which has become very successfully established in Japanese markets. Following this, iron ore gradually found a market in Japan, with exports usually based on long-term contracts. This iron ore was produced entirely in British Columbia In 1958, the Western Canadian bituminous coal industry -jointly with the Dominion Coal Board -sent an official mission to Japan to investigate the

Jan 1, 1964

OF the many categories into which scientific knowledge has been arbitrarily 'divided, the one that has proved most. applicable in our attempts to gain an insight into the details of steelmaking processes is physical chemistry. To the young metallurgist who has only recently survived a college course in this subject, the application of its principles to reactions in liquid steel should not be difficult. The many excellent textbooks of physical chemistry provide ample material on the principles of this subject for the student of steelmaking processes. It is the purpose of this chapter to provide a concise review of the principles of physical chemistry that have proved useful in studies of steelmaking and at the same time to present some of the data that are essential to the application of physical chemistry to reactions at high temperatures. Certain parts of physical chemistry require rather formidable mathematics for their complete development, but in the main those applications in which we are here interested can be expressed in fairly simple terms. Many of the equations are logarithmic, and we shall use the symbols In X and log X to represent, respectively the natural and the common logarithm of X. The two are related-by In X = 2.303 log X. Logarithms may, be read from a good slide rule with sufficient accuracy for our purposes. In a few spots a knowledge of the calculus will be helpful. MATTER Innumerable forms of matter may, be recognized, and these may be converted by chemical processes into others, as ore, coke, and air are converted into iron, slag, and gas.. Whenever such a change occurs there is a corresponding change in the amount of energy associated with the matter. The process may require an input of energy, as in the electrolytic production of aluminum, or it may result in an output of energy, as in the combustion of fuel. The basic laws of the conservation of matter and of energy tell us that we cannot change the total amount of matter or the total amour t of energy.. When the fuel pile is used up, we realize that it has simply been converted into other forms of matter; .i.e., ash

Jan 1, 1964

THE purpose of this chapter is to present a general outline of the basic open-hearth process for the benefit of students, practicing open-hearth operators, and metallurgists who wish to review the subject. The discussion is limited to a description of the sequence and purpose of the operations, illustrated by data and examples. Subsequent chapters deal with more detailed and fundamental studies of the subject. The function of the basic open-hearth furnace is to convert various types of ferrous material into finished steel of given com- position and quality. In comparison with other steelmaking methods, the basic open-hearth process is one of the most versa- tile, both from the standpoint of the raw materials that can be used and the types of steel that can be produced. The process can be considered as a sequence involving melting, refining, and deoxidation. With some types of liquid-metal charges, the melting stage is not present, but refining and deoxidation in varying degrees are fundamental features of the process. GENERAL DISCUSSION OF BASIC OPEN-HEARTH PROCESS The first consideration in open-hearth practice is the type of charge on which the operation is based. This consists of three components-fluxing, oxidizing, and metallic materials. Fluxes. In the basic process the fluxing material is primarily lime, added in the form of either limestone (CaC03) or burnt lime (CaO) . This is supplemented by magnesia (MgO) and lime from the furnace bottom and banks. The function of these fluxes is to form a slag with the silica (SiO2) , manganese oxide (MnO), iron oxides (FeO and Fe203), and phosphorus oxide (P205) that are produced by the oxidation of varying amounts of the silicon, manganese, iron, and phosphorus in the charge during melting and refining. The slag, composed of the basic fluxes and the neutral and acid oxides, floats on top of the steel bath when the charge is melted. The composition of this slag depends on the amount of each slag-forming element present in the charge and on the extent of oxidation of these elements during the course

Jan 1, 1964

By J B. Maughan

Gas and oil seeps have been known in Quebec for more than one hundred years. These occur in three main areas which contain sedimentary rocks with a total thickness estimated to vary from 6,000 to 20,000 feet. The strata in these areas are similar in many respects to those in producing areas of southwestern Ontario and the Appalachian basin, and the prospects for finding and developing commercial reserves of oil and gas in Quebec would therefore also appear to be favourable. Little of the exploratory drilling to date has been con-ducted in a systematic manner, and most of the drilling has utilized improper or inadequate equipment. Many wells have also failed to adequately test and fully evaluate the principal zones of interest. Relatively high drilling costs have hindered systematic exploration; however, with improved portable equipment, it is expected that future wells can be drilled with greater efficiency and at less cost. Most of the mineral rights in Quebec are held by the Provincial Government, and acreage can still be leased in large blocks on favourable terms.

Jan 1, 1964

By B. S. Tani, R. V. Schablaske, M. G. Chasanov

MEASUREMENTS of the solubility of scandium in liquid cadmium from 349" to 606°C by Chasanov, Hunt, Johnson, and eder' led to the isolation and characterization of the intermetallic compound ScCQ. The solid phase found in equilibrium with a saturated solution of scandium in liquid cadmium above 422°C is ScCQ. The equilibrium solid phase below this temperature has not as yet been characterized. Hexagonal needles of ScCG were isolated from a 5 wt pct Sc alloy which had been ice-quenched from 500°C. Free cadmium was leached away from the intermetallic with saturated ammonium nitrate solution. The concentration of cadmium in successive leaches was followed polarographically and the leaching process was terminated when the rate of cadmium dissolution decreased markedly. Chemical analysis of the intermetallic thus isolated is as follows: 11.5 wt pct Sc and 88.3 wt pct Cd. The composition of ScCQ is 11.8 wt pct Sc and 88.2 wt pct Cd. X-ray diffraction powder photographs of ScCds taken in a 114.6-mm Debye-Scherrer camera with CuKa, radiation can be indexed on the basis of a hexagonal nit cell. Lattice coonstants are a. = 6.330 ± 0.001A to 6.324 i 0.001A and co = 4.853 i 0.001A. The a0 has a slight range with the lower value seemingly associated with the cadmium-rich terminus of the phase. With eight atoms in the unit cell the calculated intermetallic density is 7.54 g per cu cm; the density as determined by a liquid-displacement method is 7.7 g per cu cm. Powder-diffraction data for ScCQ are recorded in Table I. Stoichiometry, symmetry, unit-cell dimensions, and the number of atoms per unit cell indicate the MgsCd (D019) type structure for ScCQ; space group is D,&-P6,/mmc. Atomic coordinates are:

Jan 1, 1964

The use of coal as a fuel causes air, pollution in; a number of different forms, and in nearly all stages of its, handling, preparation, storage, use and-disposal of its residue. First let us consider the handling of coal. As shipped, particularly to large utilities, it is run-of-mine bituminous made up of large chunks as well as pulverized particles. Because it 'is in an open car or barge, it is subject to the action o winds and the small particles may be blown around adding to the-particulate load in the atmosphere. Mien un¬loaded from the barge or car, there is again an opportunity for the wind to blow the fine particles around. All of us I am sure have seen a barge at the dock of a utility plant being unloaded by a clamshell bucket. This, after grabbing its load from the barge, lifts it some 60 or 70 feet and, then drops it on a conveyor, which carries the coal to a storage area.

Jan 1, 1964

OPEN-HEARTH refractories are not merely an accessory to the furnace. They are the furnace, to all intents and purposes. The steel work of the main structure is merely an open frame which helps to support the refractories ; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a rod protected by refractory sleeve bricks. The liquid is sometimes sent through an additional refractory- lined tundish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a nonconducting "hot top." This series, from runner and ladle to hot top, inclusive, is often referred to collectively as the "pouring-pit refractories." REFRACTORY RAW MATERIALS The raw materials available are best classified into basic and acid types. The principal basic raw materials are magnesite, dolomite, and chrome ore. The principal acid materials are silica in various natural forms, and fireclay. Magnesite. Austria was the principal source of magnesite (MgCO3) until recent years, when the Province of Quebec, in Canada, and the states of Nevada and Washington became important sources for the American steel industry. More recently these natural sources have been supplemented by the so-called "sea-water magnesite"-which is the name somewhat incorrectly given to magnesium hydroxide obtained as one of the products

Jan 1, 1964