Search Documents

By F. C. Gibson

An electrical method for the continuous determination of propagation velocities in opaque, confined explosives, and propellants is described. A resistance element imbedded in the reactive material generates electrical signals that are displayed oscillographically and indicate the position and progress of a reactive zone associated with progress of a reactive zone associated with burning or detonation. The method is applicable to both solids and liquids.

Jan 1, 1963

By D. T. Novick, M. B. Bever, B. Roessler

Ordered and disordered specimens of the alloy CusAu were cold worked and then annealed at 2880, 310°, and 340°C, together with disordered unworked specimens. me resistivity decreased during annealing mainly as a result of ordering; the resistivity measurements suggest that in cold-worked specimens the growth of antiphase domains is impeded. The strength properties increased during annealing at 288 "C; in cold-worked specimens this increase was lo a level above that for cold-worked specimens which had not been annealed. X-ray diffraction showed that after annealing for a few hours at 288ºC, the long-range order increased to a constant value; additional annealing at 288ºC resulted in the growth of antiphase domains in which the degree of order was constant. Changes in peak breadth and particle size confirmed that in cold-worked specimens the major effects of cold work were not eliminated during annealing at 288 "C, although a slight recovery process occurred. When a specimen of the alloy Cu3Au is heated to a temperature below the critical temperature (388ºC), long-range ordering tends to occur in a specimen containing less than the equilibrium amount of order characteristic of that temperature Ideally, a specimen of Cu3Au contains no long-range order if it has been quenched from above the critical temperature. Long-range order is reduced by cold work. If cold-worked specimens are heated, restoration processes such as recovery and recrystallization may occur,

Jan 1, 1963

By Albert W. Deurbrouck

This report describes the preparation characteristics of the significant, presently producing coalbeds in Mercer County, W. Va. Approximately 650,000 tons of coal was produced in Mercer County, W. Va., in 1960, of which over 630,000 tons was cleaned in four preparation plants. In 1960 the Pocahontas Nos. 3, 6, and 11 coalbeds supplied 99.5 percent of the total coal mined in the county. Because the number of working mines In this county was small, only six samples were collected; four of which were of metallurgical quality as mined. The remaining two samples could be upgraded by washing at suitable specific gravities. Many of the samples taken were of metallurgical quality as mined; however, the float-and-sink analysis on these coals has been included to point out their amenability to the production of premium quality, special purpose coals. In general the coals were low-volatile bituminous in rank with low ash and sulfur contents.

Jan 1, 1963

By J. F. Pierce, S. M. Enterline

Since January 1959 a zinc refiner of novel design has been in operation at Blackwell, Okla., producing 99.995+ zinc from the output of the Blackwell horizontal retort smelter. The refiner is a continuously operated, pyro-metallurgical unit with principal dimensions horizonhl permitting one floor operation. It is very ruggedly constructed. Furthermore it is not subjected to deterioration from high concentrations of iron in the feed metal because the boiling units are separate from the rectification columns and constructed with silicon carbide brick arches through which the heat is transferred radiantly to the zinc. A zinc refiner of novel design has been in operation since January 1959 at the Blackwell, Okla. plant of the Blackwell Zinc Co., Inc., a wholly owned subsidiary of American Metal Climax, Inc. Developed by the company's technical and operating staffs, the new refiner produces special high-grade zinc (nominally 99.995+ pct Zn) from the prime western1 slab output of the Blackwell horizontal retort smelter. The refiner is a continuously operated, pyromet-allurgical, high-capacity unit employing fractional distillation to separate zinc from its impurities, consisting principally of lead, cadmium, and iron. In prime western slab, these elements may vary in concentration from 0.005 to 1.6 pct. Table I shows the impurities usually encountered in the Blackwell prime western metal fed to the refiner together with their boiling points and vapor pressures at 907oC. The commercial pyrometallurgical smelting processes for extracting zinc from ore include distillation from retorts and a limited degree of refining can be accomplished by redistillation in similar retorts. To achieve special high-grade purity, an impractical number of batch redistillations would be required, however, with an accompanying loss of much metal. A continuously operated and integrated unit is required in which fractional vaporization and condensation can take place in a large number of stages. The first commercial continuously operated unit was developed by the New Jersey Zinc Co.4 In the separation of any two substances the degree of separation is limited if a mixture exists having a constant boiling point. The Zn-cd5 and Zn-pb6 systems contain no constant boiling points and hence these metals may be separated to any degree of purity. Basically, the pyrometallurgical refining of zinc involves three steps: a) iron, copper, and other metals having no appreciable vapor pressures at 907ºC concentrate in the bath when the impure zinc is boiled, b) lead, bismuth, antimony, and other metals having boiling points above but closer to that of zinc are selectively condensed from the vapor boiled from the bath, and c) cadmium and other metals having lower boiling points than zinc are fractionally distilled by reboiling and subsequent condensation of the zinc from the vapor. The boiling and condensation of zinc must be conducted in vessels constructed of materials which are refractory at the temperature involved (907 ºC) and it is highly desirable that they also be resistant to attack by the various metals. This requirement dictates construction from relatively small, simply shaped pieces which limits the pressures which may be employed to avoid leakage through the numerous joints. Stresses induced must be limited essentially to compressive ones and suitable provision must be made to permit thermal expansion of the components in order to minimize these stresses. Where heat is to be added for boiling or removed for condensation, refractory material through which the heat flows must have a high thermal conductivity. Silicon carbide is highly conductive but is subject to attack by iron and is expensive compared to other commonly employed refractories. A hard, dense aluminous fireclay is well suited to contain these metals where high thermal conductivity is not required. Zinc will penetrate the pores of fireclay brick but only to a limited depth in an exterior wall and has little effect other than an increase in weight and conductivity. The design objectives of the Amax refiner were: a) to achieve a long life by heavy, rugged construction and by employing silicon carbide refractories only where required for heat conductivity and not in contact with liquids of high iron concentrations, b) to simplify operation, manning and control by essentially horizontal construction, and c) to obtain high capacity in a single unit. DESCRIPTION Flow of metal through the Amax refiner is shown diagrammatically in Fig. 1 and schematically in Fig. 2.

Jan 1, 1963

By E. A. Steigerwald

E. A. Steigerwald (Thompson Ramo Wooldridge, Inc.1— he authors' results clearly indicate that cracking can be produced by the hydrogen pressure developed during a charging operation. This type of cracking or blistering has also been observed in polycrystalline materials24"28 when the charging conditions are sufficiently severe and is often referred to as irreversible embrittlement since it cannot be removed by a baking treatment. There are additional data, however, which must be considered before a pressure theory can be generally employed to account for all failures which occur as a result of hydrogen. In many cases, hydrogen embrittlement in a tensile test or in delayed failures under static loads is a reversible phenomena which cannot be simply explained on the basis of preexisting cracks generated by the charging operation. It is this aspect of the problem which has prompted many investigators to seek mechanisms other than hydrogen pressure to explain their results.24'n728 Fig. 15 indicates an example where, under specific experimental circumstances, hydrogen embrittlement can occur at liquid nitrogen temperatures. In this case, which has been previously decribed,'' specimens were charged with varying quantities of hydrogen, immediately quenched, and tested in liquid nitrogen (-320°F). A companion set of identical specimens were charged, aged at 300°F to remove the hydrogen, and also tested at -320°F. When the current density was greater than lo-' amp per sq in., embrittlekent occurred in both sets of specimens, indicating that cracking had occurred during charging and the embrittlement, as in the case of Fe-Si single crystals, was irreversible. At current densities between approximately 103 and lo-' amp per sq in, the embrittlement was present only for those specimens which contained hydrogen during the testing sequence. The embrittlement was therefore reversible with respect to the aging and charging operations. Since extensive hydrogen movement would not be expected at -320°F, it is difficult to reconcile these data with a mechanism which requires pressure and pressure dependent growth of preexisting cracks. There are other features of hydrogen embrittlement such as the reversibility of the incubation time for delayed failure with respect to applied stressg0 and the influence of prestraining31 which are also difficult to explain using a pressure model. Any general mechanism of hydrogen embrittlement will have to consider the reversible aspects of the embrittlement data as well as the irreversible portion which has been clearly presented for the Fe-Si crystals and which is consistent with a pressure model. A. S. Tetelman and W. D. Robertson (authors' reply)—he authors agree with Dr. Steigerwald that a general mechanism of hydrogen embrittlement must be applicable in all cases where embrittlement occurs. Dr. Steigerwald's experiments were performed on an iron alloy which has an extremely complex microstructure, and therefore does not lend itself to the direct and detailed observations that can be made in Fe-Si. The change in the characteristics of cracks as a consequence of annealing at 300°F is not really known in detail but it is probable that stress-relaxation (blunting) occurs, dislocations produced near the crack tips will be pinned by carbon atoms, and hydrogen will be lost to the atmosphere. Any, or all of these effects of annealing will alter the ease with which a crack subsequently propagates under applied stress. A quantitative treatment of the problem must take these effects into account. Since diffusional processes are presumably eliminated at -320°F, the general mechanism proposed by Dr. Steigerwald's colleagues cannot be operative at this temperature. A detailed discussion of the general' inapplicability of this mechanism has been presented elsewhere. However, the data presented by Dr. Steigerwald in his discussion can be explained in terms of a pressure model. Crack propagation under internal pressure P and applied stress occurs when where is the total energy expended in creating new surface area and by plastic work at the crack tip. The total crack length increases with increasing current density, since we have shown that it systematically increases with hydrogen concentration and Dr. Steigerwald has shown that hydrogen concentration increases with current density. For large L (high current density) Eq. [I] can be satisfied even if P = 0 and the embrittlement process does not require the presence of hydrogen. Specimens charged at a lower current density will con-

Jan 1, 1963

By H. M. Thorne

Industrial shale-oil operations in North America and Europe predated the Drake discovery, but, since then, most have succumbed to competition from petroleum. However, the existence of enormous oil-shale resources in the Green River formation of Colorado, Utah and Wyoming [estimated at over a trillion bbl of shale oil in place] and the advancement of United States oil- shale technology by research and development programs of government and industry during the past 15 years point to a natural partnership of petroleum and oil shale to meet the accelerating energy demands of the future. The utilization of oil shale is not a question of limited petroleum supplies, but one of economics. Two factors are expected to improve the economic outlook for industrial shale oil production -- a rise in petroleum replacement cost and further advances in oil-shale technology.

Jan 1, 1963

By E. C. Nelson

An equation is derived for calculating approximately the solubility of nitrogen in an alloy steel over a temperature range from 1200" to 1900°C using data on the effects of alloys on the activity coefficient of nitrogen in iron at 1600°C. Calculated values are compared with experimental data. STUDIES involving the solubility of nitrogen in complex iron alloys have been aided by a system devised by Lanenberg for calculating the solubility of nitrogen in ternary and higher alloys of iron at 1600C using available data on the activity coefficient of nitrogen in binary alloys. Calculated nitrogen solubilities agree well with experimental determinations on complex alloys,' and the calculation procedure is useful when experimental data on specific alloys are not required. A method for extending calculations of nitrogen solubilities in alloy steels to temperatures other than 1600°C would be useful because of the paucity of experimental data in this area. Assumptions which must be made to permit this calculation introduce an element of approximation; however, the calculation is useful in cases where a large number of alloys and temperatures are under consideration, and the precision of experimental measurements is not required. The activity coefficient can be freed from the isothermal restriction of Langenberg's calculation if it is assumed that the solution is "regular". This is a reasonably good assumption for solutions of nitrogen in iron alloys, because usually they are dilute and the heat of solution is relatively small. The presence of large amounts of certain alloying elements would make this assumption less tenable.3 One of the properties of a regular solution is: when "f" is the activity coefficient of a solute and "T" is the temperature in OK. If the activity coefficients at temperatures T and T2 are denoted by subscripts 1 and 2 respectively: The activity coefficient of nitrogen in a complex alloy then can be calculated at any temperature from the sum of the effects of the other solutes on the activity coefficient of nitrogen at 1600°C. It will be convenient to incorporate this expression into an equation which will give directly the logarithm of the solubility of nitrogen at any temperature in the presence of alloys. Two constants, the solubility of nitrogen in pure iron at 1600 "C and the partial molar heat of solution of nitrogen in iron are required. The heat of solution value of 1400 cal at 1600 °C quoted by Kubaschewski and vans will be used. The accuracy of the calculation will suffer if the heat of solution should change materially with temperature. In the absence of experimental data on the temperature dependence of this quantity, it will be expedient to restrict the application of the calcula-

Jan 1, 1963

By C. E. Johnston

In December 1956, International Minerals & Chemical Corp. installed a rope-suspended belt haulage system in its Carlsbad, N. M., potash mine to complement the already existing rail transport arrangement. In this article the author describes when and where each system is used, the advantages and disadvantages of both, and future planning and proposed changes in haulage at IMC. The haulage system at the International Minerals & Chemical Corporation (IMC) potash mine near Carlsbad, N. M., reached a turning point in December 1956 with the introduction of rope-suspended belt haulage. In fact, IMC pioneered the use of this type of belt in the potash industry. Since that time belt conveyance has been employed as an extension of the rail system but not as a replacement of the main rail haulage. IMC's potash mine is located in the Permian Basin, approximately 20 miles east of Carlsbad in Eddy County, N. M. The 800, 850 and 900-ft levels have been exploited. From these levels over 60 million tons have been extracted. The two ore minerals are sylvite (KCl) and langbeinite (K2SO4. 2MgSO4). The principal gangue mineral is halite, with minor amounts of polyhalite, kainite and leonite. Langbeinite is mined on the 850-ft level and sylvite on the 900. The 800-ft level, with both langbeinite and sylvite mineralization, is idle. Mining heights vary from 54 in. to over 10 ft. A room and pillar mining system is used. Geologically, mining is done in the Salado salt formation. The U.S. Geological Survey has classified the 900-ft sylvite level as the first ore zone and the 850-ft langbeinite level as the fourth ore zone. Since the grade of sylvite is low, mineralization at the IMC mine is somewhat irregular and salt horses, are common. Selective mining and a flexible haulage

Jan 1, 1963

By Carl Rampacek

The conversion of dilute sulfur dioxide gas into sulfuric acid by autoxidation in mechanical cells of the flotation or gas absorber types was investigated. Bench-scale tests were made with sulfur dioxide-air mixtures to determine the influence of several factors on autoxidation of sulfur dioxide, using iron and manganese salts as catalysts. The laboratory investigation subsequently was extended to pilot plant acid-making tests, using a modified turbomixer gas absorber having a 12-inch-diameter impeller. Sulfur dioxide gas was produced for the tests by roasting pyrite in a fluidized-bed reactor. In the better tests, made with manganese sulfate as the catalyst, the equivalent of 1,000 pounds of anhydrous H2SO4 was produced per 24 hours as a 10-percent solution; power consumption was 0.2 kwhr per pound of equivalent anhydrous acid synthesized. The batch and continuous tests demonstrated the technical feasibility of producing dilute sulfuric acid by autoxidation of sulfur dioxide gas in mechanical cells when converting pyrite roaster or waste smelter gases.

Jan 1, 1963

By L Gill

The four basic types of electric motors -squirrel-cage, wound rotor, synchronous and D.C. -are de-scribed, with particular reference to speed-torque characteristics. The three classifications of squirrel-cage motors, C.E.M.A. B, C and D, are compared, and methods of selection for specific drives are outlined. Wound rotor and synchronous motors are covered from the viewpoint of construction details, methods of operation and control required. The application of these motors to crushers, conveyors and ball mills is described and reasons for their selection are given. The application of D.C. motors to haulage equipment and mine hoist drives is included, and the basic principles of a variable voltage drive are illustrated. Efforts have been made through-out to provide specific examples of motor selection, with particular reference to the mining industry. THIS paper will attempt to answer the question -"which motor should be used for a specific drive?" Although it is impossible to cover the complete subject of electric motor application here, we hope to give some idea of the types of motors available and why certain types are used on specific applications.

Jan 1, 1963

The first stage in the refining of lead blast furnace bullion is the removal of copper and is normally done as a batch process in open kettles.A number of attempts have been made to establish continuous processes operating in reverberatory type furnaces, but the growth of accretions in the furnace has always presented a serious problem.The Broken Hill Associated Smelters Pty. Ltd. (RH.A.S.) at Port Pirie have overcome this problem by constructing a reverberatory furnace and ancillary cooling system of a novel design.Although a number of mechanical and metallurgical problems still remain to be solved, it is claimed that a workable continuous copper drossing process has been established.INTRODUCTIONLead bullion emerging from the blast furnaces at Port Pirie is at a temperature of about 1100°C and contains, among other impurities, about 1 per cent of copper.The first stage of refining is the removal of this copper by a drossing operation and in the past this was done, batchwise, by allowing the bullion to cool back in 100 ton kettles.At about 700°C, copper dross begins to separate as a crust on the surface of the kettle and this separation was allowed to continue down to about 450°C when the crust was brokenup and skimmed manually using a long handled, balanced, spoon. The dross was then smelted in a reverberatory furnace to produce a saleable copper matte and separate out lead bullion, which was returned to the drossing kettles. The copper content of the drossed bullion was then further reduced by a sulphur treatment process.The drossing operations involved hard manual labour under arduous conditions and the pouring of hot bullion into...

Jan 1, 1963

By G. S. Tint, M. Herman, V. V. Damiano

Dislocation arrays and substructures were studied in cadmium doped zinc crystals using a newly devised etching technique. Cadmium precipitates delineating the dislocations were revealed by etching a surface closely parallel to the (0001) slip plane. Cinephotomicrography of the continuous etching process revealed the three-dimensional aspects of dislocations in the bulk crystal. Dislocation etch patterns were studied in both deformed and annealed crystals after suitable aging at room temperature. The effect of annealing was evidenced by a rearrangement of the dislocations into low-angle boundaries and hexagonal networks. ETCH pit techniques have been used extensively to study dislocations in both deformed and annealed bulk metal crystals. Ideally one hopes to obtain a one-to-one correspondence between the etch pits and the points of emergence of the dislocations at the surface. One then attempts to deduce the way in which dislocations are arranged in the bulk crystal from the arrangement of etch pits on the surface. It is clear that one can obtain only limited information of the dislocation configurations inside the crystal from etch pit studies of single surfaces. Considerably more information is obtained if one is able to follow the course of the dislocations through the crystal using progressive etching technique. Techniques of this sort were used by Gilmanl to study dislocations on the slip planes of NaCl crystals and by Damiano and Tint2 to study dislocation arrangement in zinc crystals grown from the melt. The present paper makes use of a technique first described by Tint and Damiano3 to observe and continuously record the dislocation structures which appear while a crystal surface was being progressively etched. Studies were made on cleaved (0001) surfaces to reveal the dislocations along their length on the surface closely parallel to the slip plane. The technique for revealing segments of dislocations along their length by etching is well known. Wilsdorf and Kuhlmann-wilsdorf4 revealed disloca- tions along their length in aluminum containing a few percent copper, when precipitates segregated along the dislocations. The technique was used by Low and Guard5 to study dislocation configurations on the slip plane in Fe-Si alloys containing carbon. In the present work the technique was applied to zinc containing cadmium since it was shown by Gil-man6 that a cadmium-rich phase could be made to precipitate from supersaturated solutions along dislocations in zinc. Segments of dislocations delineated by the precipitates were revealed by etching a surface prepared by cleaving the crystal. The three-dimensional nature of dislocations and substructures was thus studied from the cinephotomicro-graphic record of the continuous etching process. EXPERIMENTAL Single crystals of zinc containing the order of 0.1 pct Cd were prepared by slowly lowering a graphite crucible containing the melt through a temperature gradient of 15°C per cm at a rate of 1.5 X 10-3 cm per sec. "As grown" crystals were aged for periods of 1 month at room temperature, then cleaved in liquid nitrogen, and etched according to the procedure used by Gilman.' The etchant containing 32 g of CrO3, 6 g of hydrated Na2SO3 in 100 ml of water behaved as a chemical polish for zinc and etch pits were produced at the site of precipitates or inclusions. After the precipitates or inclusions were removed from the surface, the etch pits left behind were eventually polished smooth. This behavior enabled one to continuously observe the surface while the specimen was immersed in the etchant. Best results were obtained when the specimen surface was vertical and the reaction products of polishing were continuously removed by gravitational convection. Some crystals were heavily deformed in excess of 25 pct strain, others were lightly deformed the order of a few pct by compression such that the deformation occurred essentially by basal glide. Some crystals were etched immediately after deformation, others were allowed to age at room temperature for several weeks prior to etching. Heavily deformed crystals were annealed at various temperatures and etched on the cleavage plane immediately after annealing, others were allowed to age at room temperature for several weeks prior to etching. The etched structures of deformed and annealed structures were studied. Similar experiments were conducted on 99.9999 pct pure zone refined Tadanac zinc crystals which

Jan 1, 1963

By P. A. Wasson

The investigation described in this publication was conducted by the Bureau of Mines to determine the effectiveness of the anionic silica flotation method on goethitic iron-bearing materials from the Cuyuna Range, Minn. Samples used in this investigation were a composite of drill core from 13 holes, and 3 samples from lean ore stockpiles. These samples are believed to be typical of the mineralization occurring in an area with a potential reserve of several million tans of submarginal iron ore. Results from batch tests showed that the iron-bearing minerals could be effectively concentrated by flotation removal of the siliceous gangue. The drill hole composite yielded laboratory flotation concentrates from locked tests containing 56.8 percent Fe and 6.1 percent silica, with an accompanying iron unit recovery of 94.2 percent. Concentrates containing 52.4 to 53.7 percent Fe also were produced from the lean ore stockpile materials; corresponging iron recoveries ranged from 71 to 79 percent in the batch tests, with the possibility remaining for additional recovery of iron from the middlings.

Jan 1, 1963

By John F. Elliott, Martin Weinstein

The solubility of hydrogen in liquid Pure iron and in a number of liquid binary iron alloys has been measured in a Sieverts'-type apparatus. Sieverts' law is obeyed in all alloys studied UP to 1 atm Pressure H2. The alloying elements, Al, B, C, Co, Cu, Ge, P, S, and Sn, decrease the solubility while Cb, Cr, Mn, and Ni increase it. ALTHOUGH the importance of hydrogen in steel-making has long been recognized, there has been, until recently, very little information in the literature on the effect of alloying elements on the solubility of hydrogen in iron. There is also disagreement on the solubility of the gas in liquid pure iron. Because of the earlier work in this laboratory,1,2 with the Sieverts method to determine the solubility of nitrogen in liquid iron alloys, it was decided to apply the equipment and procedure to hydrogen. The literature that is pertinent to this study (Ftefs. 1 through 15) will be discussed later when the results of this investigation are considered rather than at this point to avoid repetition. The reaction under study is:

Jan 1, 1963

By J. W. Downey, J. B. Darby, L. J. Norton

THE only previous investigation of the phase equilibria in the Ta-Pd system was reported by Greenfield and Beck.1 Their work (actually a portion of a much broader survey) was limited to the composition range 50 to 75 at. pct Ta and to a single temperature, 1000°C. The results indicated that no intermediate phases were present at this temperature. They pointed out that this was an unexpected result in view of the fact that niobium, which belongs to the same group in the periodic table as tantalum and has essentially the same atomic size, forms a o phase with palladium.' Also, tantalum in combination with rhodium,' iridium,' or platinum' stabilizes the s phase. By analogy, the Ta-Pd system would also be expected to contain a s phase. The present investigation was therefore undertaken to explore more fully the phase relationships in this system. Alloys were prepared by arc melting on a water-cooled copper hearth in an argon-helium atmosphere. The purity of the starting materials was greater than 99.9 pct. The weight losses on melting were less than 1 pct and therefore the alloys were not analyzed chemically. Specimens were wrapped in molybdenum foil, encapsulated in quartz capsules under a vacuum of at least 1 x 10-5 mm of Hg, annealed as indicated in Table I, and water quenched. Optical and X-ray metallography were used for identifying the phases present in the annealed and quenched alloys. The alloys were resistant to attack by several acids; however, a sodium cyanide electroetch and an immersion etch containing 1 part HF, 1 part HNO3, 2 parts H2SO4, and 5 parts H2O by volume were found satisfactory. The X-ray diffraction patterns were taken with a Straumanis-type Debye-Scherrer camera and filtered copper or chromium radiation. A summary of the phases found in this investigation is presented in Table I. No attempt was made to determine the composition limits of the various phases. The present results indicate that this system consists of two terminal solid solutions separated by at least four intermediate phases at the approximate compositions Ta3Pd, -TaPd, TaPd,, and TaPd3. The Ta-rich solid solution, containing less than 10 at. pct Pd at 1150°C, is in equilibrium with a o phase which is stable in the vicinity of 25 at. pct Pd. The latter phase is also in equilibrium with a bct phase at the equiatomic composition. At high temperatures it appears that the Pd-rich solid solution extends to at least 66.6 at. pct Pd and is in equilibrium with the bct phase. When annealed at 900°C, a sample containing 66.6 at. pct Pd transformed to an unidentified phase designated as X. An X-ray diffraction pattern of this phase contained sharp low-angle lines while the high-angle lines were characteristically diffuse. The observed d-spacings and relative intensities for lines in the low-angle region are presented in Table 11. In the vicinity of 70 at. pct Pd an intermediate phase having the TiA13-type structure is formed. It is stable to at least 1100°C, and presumably dissolves congruently into the ter-

Jan 1, 1963

By A. H. Daane, W. J. Wunderlin, B. J. Beaudry

The solid solubility of holmium in copper, silver, and gold, determined using metallographic techniques, was found to be a maximum of 0.06, 2.4, and 3.2 wt pct, respectively, nt the eutectic temperatures. The temperatures of these eutectic horizontals, determined by differential thermal analysis, were found to be 868", 787", and 778"C, respectively. The first compound on the silver-rich side of the Ag-Ho system was found to be A&Ho2. In a study by Gold et al.,' on the effect of small amounts of soluble impurities on the electrical resistance and thermoelectrical properties of copper, traces of iron were shown to have drastic effects on the thermoelectric power due to the magnetic scattering of the conduction electrons. Since little is known about the state of the iron ion when dissolved in copper, Gold had hoped to repeat these experiments using certain rare earths as the magnetic scattering centers; because of the tightly bound 4f electrons it is not expected that their spectroscopic state would be affected by alloying. In such an experiment the sole role of the trace rare-earth impurity would be to magnetically scatter the copper conduction electrons without producing appreciable distortions in the otherwise pure copper matrix. Since holmium was chosen for such a study because of its high magnetic moment, it was necessary to establish precisely its solid solubility in copper. The study was extended to include the solvents silver and gold, so that an evaluation of the data using classical solubility parameters could be made. No previously reported work on the systems of holmium with copper, silver, or gold was found in the literature. Information on the solubility of other rare earths in these three metals is also very meager. The solubility limit of yttrium in copper was reported as less than 1 wt pct2 and the solubility of praseodymium in gold as 0.35 wt pct,3 while no references were found on solubility studies of rare earths in silver. EXPERIMENTAL Materials. The materials used in this investigation were distilled holmium prepared in this Laboratory, OFHC* copper, electrorefined silver (99.9 *OFHC = oxygen-free high conductivity. pct), and gold with the analyses given in Table I. Sample Preparation. Samples weighing 1 to 2 g were prepared by arc-melting the components together on a water-cooled copper plate under purified argon atmosphere. The samples, turned and remelted at least five times to ensure homogeneity, showed weight changes of less than 0.1 wt pct after melting. Samples containing less than 0.7 wt pct Ho were prepared by diluting 1 to 2 wt pct Ho alloys with the pure solvent, while samples with concentrations greater than 0.7 wt pct Ho were prepared directly from the metals. The samples were wrapped in tantalum foil, sealed in outgassed Vycor tubing under helium, annealed at the desired temperature for at least 24 hr, and then quenched by shattering the Vycor tube in cold water. Metallographic Methods. Standard mechanical polishing methods were used in preparing the silver and gold alloys for examination, while the copper alloys were electropolished using a 40 pct solution

Jan 1, 1963

By C. L. Coldren

Recently there has been much discussion of the use of pipelines for the long-distance transportation of solids. Many have come to recognize the economies inherent in pipeline transportation. The widespread movement of oil and gas at astonishingly low costs - a gallon of oil moves from Montana to New York for less than that for the delivery of a postcard - has spurred others to sturdy this mode of transportation. Most interested people are aware of the inherent advantages of pipelines - continuity and reliability of operations - low manpower requirements per ton mile - moderate capital costs per ton mile - low maintenance costs per ton mile - low operating costs per ton mile.

Jan 1, 1963

By Robert Stefanko

The importance of underground stress instrumentation cannot be minimized. It was Lord Kelvin who said that unless you can assign a number to a quantity,, you know very little about it. Most engineers will agree although this kind of statement is resented by our friends in non-technical fields. Mining is undergoing a revolution from art to science. But how can mining methods be optimized if there is no way of measuring the effectiveness of a given mining method? Do we know how effective a' support is unless we can determine its reaction to the mine structure? How do we assess the need for modifications to existing systems and supports, and how do we measure the effectiveness of such changes? Cut and try techniques are too wasteful of time and energy, and rarely provide solutions to a given problem. The purpose of underground stress instrumentation is to provide answers to some of the above questions -- answers that cannot be obtained otherwise This does not mean that laboratory studies are not valuable -on the contrary. Laboratory and underground studies supplement one another. Rock mechanics had its conception with the study of stresses in homogeneous, isotropic, and elastic models subjected to various force systems. These analyses were valuable inasmuch as they pinpointed possible sources of trouble due to stress concentrations. If the results observed underground did not always agree with the experimental analysis, it was not an indictment of the latter. More probably, the discrepancy could be attributed to the lack of similitude between model and prototype. The more nearly one can simulate underground conditions in a model, the more apt one is to produce results which correlate well-with underground observations. It is impossible to completely simulate underground conditions because all of the significant design parameters have not been recognized and evaluated. What better way can one evaluate these parameters than by underground stress instrumentation?

Jan 1, 1963

By H S. Ellis

Flow studies have been conducted on nickel-water suspensions in a 1in.-diam., 42-ft.-long transparent lab-oratory pipeline at concentrations of up to 25 per cent, by volume, and slurry velocities of up to 15 ft/sec. The average size of the nickel powder was approximately 150 mesh (106J.L). Three flow regime were noted. At the highest velocities, i.e., above 10 ft/;sec., where the concentration distribution through the vertical diameter was most uniform, pressure gradients could be correlated with the Durand-Condolios equation (7,8). An intermediate region, i.e., from 7 ft/sec. to10 ft/sec., could be distinguished, the lower velocity limit being that at which nickel particles began to deposit. This region was also marked by decreasing pressure gradients, for a given concentration, as the velocity was reduced. The upper velocity limit in this region was also uniquely defined in that the friction factor for any nickel concentration was the same as that for water. In the third regime, below about 7 ft/sec

Jan 1, 1963

By John Henderson

FOR some time now the most commonly accepted description of liquid silicate structure has been the "discrete ion" theory, proposed originally by Bockris and owe.' This theory is that when certain metal oxides and silica are melted together, the continuous three dimensional silica lattice is broken down into large anionic groups, such as sheets, chains, and rings, to form a liquid containing these complex anions and simple cations. Each composition is characterized by "an equilibrium mixture of two or more of the discrete ions",' and increasing metal oxide content causes a decrease in ion size. The implication is, and this implication has received tacit approval from subsequent workers, that these anions are rigid structures and that once formed they are quite stable. The discrete ion theory has been found to fit the results of the great majority of structural studies, but in a few areas it is not entirely satisfactory. For example it does not explain clearly the effect of temperature on melt structure,3 nor does it allow for free oxygen ions over wide composition ranges, the occurrence of which has been postulated to explain sulfur4 and water5 solubility in liquid silicates. In lime-silica-alumina melts the discrete ion theory is even less satisfactory, and in particular the apparent difference in the mechanism of transport of calcium in electrical conduction8 and self-diffusion,' and the mechanism of the self-diffusion of oxygen8 are very difficult to explain on this basis. By looking at melt structure in a slightly different way, however, a model emerges that does not pose these problems. It has been suggested5" that at each composition in a liquid silicate, there is a distribution of anion sizes; thus the dominant anionic species might be Si3,O9 but as well as these anions the melt may contain say sis0:i anions. Decreasing silica content and increasing temperature are said9 to reduce the size of the dominant species. Taking this concept further, it is now suggested that these complexes are not the rigid, stable entities originally envisaged, but rather that they exist on a time-average basis. In this way large groups are continually decaying to smaller groups and small groups reforming to larger groups. The most complete transport data 8-10 available are for a melt containing 40 wt pct CaO, 40 wt pct SiO2, and 20 wt pct Al2O3. Recalculating this composition in terms of ion fractions and bearing in mind the relative sizes of the constituent ions, Table I, it seems reasonable to regard this liquid as almost close packed oxygens, containing the other ions interstitially, in which regions of local order exist. On this basis, all oxygen positions are equivalent and, since an oxygen is always adjacent to other oxygens, its diffusion occurs by successive small movements, in a cooperative manner, in accord with modern liquid theories." Silicon diffusion is much less favorable, firstly because there are fewer positions into which it can move and secondly, because it has the rather rigid restriction that it always tends to be co-ordinated with four oxygens. Silicon self-diffusion is therefore probably best regarded as being effected by the decay and reformation of anionic groups or, in other words, by the redistribution of regions of local order. Calcium self-diffusion should occur more readily than silicon, because its co-ordination requirements are not as stringent, but not as readily as oxygen, because there are fewer positions into which it can move. There is the further restriction that electrical neutrality must be maintained, hence calcium diffusion should be regarded as the process providing for electrical neutrality in the redistribution of regions of local order. That is, silicon and calcium self-diffusion occur, basically, by the same process. Aluminum self-diffusivity should be somewhere between calcium and silicon because, for reasons discussed elsewhere,' part of the aluminum is equivalent to calcium and part equivalent to silicon. Consider now self-diffusion as a rate process. The simplest equation is: D = Do exp (-E/RT) [I] This equation can be restated in much more explicit forms but neither the accuracy of the available data, nor the present state of knowledge of rate theory as applied to liquids justifies any degree of sophistication. Nevertheless the terms of Eq. [I] do have significance;12 Do is related, however loose this relationship may be, to the frequency with which reacting species are in favorable positions to diffuse, and E is an indication of the energy barrier that must be overcome to allow diffusion to proceed. For the 40 wt pct CaO, 40 wt pct SiO2, 20 wt pct Al2O3, melt, the apparent activation energies for self-diffusion of calcium, silicon, and aluminum are not significantly different from 70 kcal per mole of diffusate,' in agreement with the postulate that these elements diffuse by the same process. For oxygen self-diffusion E is about 85 kcal per mole,' again in agreement with the idea that oxygen is transported,

Jan 1, 1963