Search Documents

By Lucia Vieira

Kelvin probe force microscopy (KPFM) can be used to monitor electrostatic charges on the surfaces of materials. In this paper, we describe the use of KPFM to evaluate the electrostatic effect induced by silver nanoparticles incorporated as clusters in diamond-like carbon (DLC) films, before and after scratching. The results are compared to those obtained for DLC films without silver nanoparticles. Raman spectroscopy was used to identify the DLC signature, and energy dispersive X-ray spectroscopy (EDX) was used to confirm the presence of silver in the film. The morphology of the DLC film containing silver was investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The findings suggest that the incorporation of silver nanoparticles in amorphous materials could offer new options for electrostatic energy storage on the surfaces of these materials.

Jul 31, 2018

By Claudio José Martins da Silva

A planta siderúrgica da TKCSA possui em seu sistema de distribuição de gás dois flares (bleeders) que possuem funções distintas durante o regime normal de operação. O flare 2 é responsável por queimar o gás de alto forno de baixo poder calorífico, gerado no início do processo de partida do alto-forno até que o gás atinja as características adequadas para o aproveitamento e ser direcionado para o gasômetro. Já o flare 1 trabalha em conjunto com o gasômetro no processo de controle de pressão e vazão excedente de gás, quando da redução intempestiva de consumo de gás de alto forno. O presente trabalho apresenta a solução implantada pela TKCSA para garantir, sob quaisquer condições de fornecimento de energia elétrica, a operação dos equipamentos elétricos e de todo o sistema de automação e controle operacional dos flares. Podemos dizer que a operação do flares torna-se autônoma e relação ao sistema elétrico e sistema de automação e controle da distribuição de gás de alto forno. O sistema implantado promoveu uma elevação na segurança operacional dos flares, já que, a autonomia operacional impede o apagamento da chama eliminado a possibilidade de lançamento de gás cru na atmosfera.

Jul 31, 2018

By Cermets

Ti(C,N)-based cermets offer good high temperature strength, perfect chemical stability, excellent wear resistance, and relativly better machinability. In the present work, the tribological behaviors of Ti(C,N)/SiC sliding pairs lubricated in water and seawater were evaluated using a ball-on-disk tribometer. The experimental results show that a relatively low friction coefficient (about 0.025) can be obtained when lubricated with artificial seawater at the sliding speed of 200 mm/s, while the date is about 0.2 in purified water. The wear surface profiles and the lubricants collected after running-in process for the high/low friction conditions were compared. In addition, the effect of salt molar concentration of the lubricant on the Ti(C,N)/SiC friction properties was investigated. It was found that the smooth and flat surface is the premise to gain the low friction. At the same time, the proper concentration of silica colloid, which is affected by the salt ions, is also an essential one. Moreover, the high sliding speed (200 mm/s) is beneficial to achieve low friction.

Jul 31, 2018

By Jesús A. Carlos Cornelio

Since their discovery in 1991 Carbon nanotubes (CNTs) have attracted much interest due to their remarkable mechanical, thermal, electrical, chemical and optical properties. In connection with their mechanical properties, CNTs have been studied in various forms for tribological applications including their use as lubricant additives for oil and water. In this paper the tribological properties of CNTs (SWCNTs and MWCNTs) when used as lubricant additives are studied under rolling-sliding conditions in a twin-disc testing machine. The tests were performed using 5% of creepage and pressures of 0.8 GPa and 1.1 GPa. Used functionalized nanotubes were modified with carboxylic acid ultrasonically dispersed at different concentrations (0.01, 0.05%). The results indicated that the presence of carbon nanotubes leads to a decrease in both friction coefficient and wear rate for both systems studied (oil and water).

Jul 31, 2018

By Priscilla Pessin Coppo

The prevention of dental enamel wear has particular relevance for preventive and restorative purposes in dentistry. The wear damage can increase due to salivary disorders and/or parafunction (bruxism); antagonists incisal surfaces become flat and coincident. This study aims to investigate the wear behavior and the related mechanisms in sliding pairs of conformal incisal enamel, with similar values of hardness and fracture toughness, with different applied normal loads and lubricated conditions. Bovine incisors, under pin on flat configuration, were tested in two lubrication condition (dry or with natural saliva) and two applied normal loads (8 and 16 N). The worn surfaces were investigated by 3D profilometry and SEM. The analysis of worn surfaces indicated mechanisms of brittle fracture, but with different severities. Under a normal load of 16 N and dry condition, wear is controlled by a brittle process: microcracking with flake-like wear particles, which results in high friction coefficient (> 0.85), wear rate and wear volume. On the other hand, under a normal load of 8 N and natural saliva, wear took place in the interprismatic region, with consequent exposure of prisms and fracture in localized regions. In this case, the friction coefficient was 16% lower and the wear volume was one order of magnitude lower. Under 8 N and natural saliva, the wear was greater than in the dry condition, probably due to tribochemical reactions.

Jul 31, 2018

By Caio Luca Joppert

O objetivo do trabalho foi estudar a possibilidade de ajustar as características do biogás produzido a partir da fermentação de vinhaça de modo a torná-lo intercambiável com o Gás Natural (GN), ou um GN substituto (GNS) com características que permitam introduzi-lo na rede de distribuição. São considerados aspectos normativos e técnicos associados à composição química e comportamento durante processo de combustão visando o atendimento aos requisitos normativos estabelecidos para o GN. O trabalho considera a vinhaça, rejeito da produção de etanol a partir da cana-de-açúcar, como fonte para produção do biogás em razão da grande disponibilidade deste resíduo do setor sucroalcooleiro. O Estado de São Paulo (ESP) é tratado com destaque, uma vez que este concentra a maior parte da produção do setor sucroalcooleiro no Brasil. Cálculos de razões de mistura tratada com gases de ajuste foram realizados para verificação das proporções necessárias que viabilizam a utilização da mistura como GNS, tendo como referência especificações da ANP. Os resultados do estudo indicam que a alternativa de geração e beneficiamento de biogás da vinhaça é uma opção tecnicamente viável de conversão de fração considerável deste resíduo do setor sucroalcooleiro em gás com características similares ao GN. Ademais, a alternativa proporciona a valoração do conteúdo orgânico do resíduo, com redução da contaminação dos solos no processo de reaproveitamento dos nutrientes nos processos de fertirrigação.

Jul 31, 2018

By Hugo M. Checo

Friction-reducing textures for lubricated mechanisms have received much attention since the advent of microtexturing techniques. In this work we consider the piston ring/liner contact, numerically simulating the rings as they slide against a textured liner. This situation has not been sufficiently analyzed because its numerical complexity is much greater than that of texturing the rings. Further, we consider the actual typical geometries of oil-control, wiper and compression rings, under realistic loads and velocities. The results show the possibility of friction reduction when the texture on the liner is properly designed, identifying starvation alleviation as a crucial intervening mechanism.

Jul 31, 2018

By Dyego Monteiro de Souza

This study compares the wear resistance of specimens lubricated with biofluids or mineral oil. Tribological studies were performed by ball-cratering test. In these tests were used as lubricants epoxidized soybean oil, castor oil and mineral oil. The specimens used were untreated and nitrided AISI 4140, while a steel ball AISI 52100 was used as a counterbody. In order to analyze the results obtained, the worn volume was calculated and the characterization of the crater, after the test, was made using optical microscopy and SEM. Wettability was also measured for the different surface condition and lubricants. As expected both specimens showed a smaller volume worn when lubricated with mineral oil due to inherent properties of this type of lubricant. Among the vegetable oils studied, the castor oil showed a better performance in the lubrication of the specimens untreated while on the nitrided specimen have shown less wear when lubricated with epoxidized soybean oil, indicating a difference in the efficiency of oils, as lubricants, depending on the surface conditions of the mechanical components.

Jul 31, 2018

By Angelo dos Reis Magalhães

Brazilian companies have adopted in recent years new management practices to remain competitive. Specialized consulting in asset management progressively creates or adapts new techniques in order to increase availability and reduce manufacturing costs, maximizing profits. New engineering concepts were acquired and implemented by executives in all business segments. Techniques, such as FMEA, RCM, LCC, Pas 55, Reliability studies by Monte Carlo simulations, among others, have become increasingly recognized as important tools to enhance managerial performance. Besides these techniques, this study suggests the importance of adequate structuring of a lubrication program, as a critical success factor for the reliability of any asset. Through a case study developed with a company in the mining sector, this work proposes the development of a master plan for lubrication based on three pillars: People, Equipment and Management system. Practices and care with lubricants, hydraulic fluids and coolant, until its point of application, shall be evaluated to ensure a correct contamination control and a high level of assets availability. This discussion sheds light onto other benefits of this process, including occupational health and safety; ergonomics; environment and sustainability.

Jul 31, 2018

By Lionel Loïc Limol

Polymeric materials, such as polyurethanes and rubbers, are widely used in the mining industry because of their moderate cost and excellent mechanical properties. Such polymers have been used mainly in transportation (conveyor belt systems and pipes coatings) and screening, for their appreciable abrasion wear resistance. Studies revealed the complex influence of test parameters, such as grit size and applied normal load, on the abrasion wear process for polymers. In this study, the abrasive wear behavior of several polyurethanes and rubbers were investigated at room temperature according to a rotary drum abrasion method (DIN 53516). Wear tests were carried out at 26 cm/s test speed and load value of 5 N and 10 N. Corundum paper grit varying from 60 to 400 mesh were used as an abrasive surface. After each test the mass loss of the pin was recorded and the wear rates were calculated from wear volume. The wear surfaces were investigated by scanning electron microscopy.

Jul 31, 2018

By Gustavo Borges Tiboni

The erosive wear caused by the impact of solid particles against a surface is a tribological phenomenon present in many segments of the industry, such as transportation, aerospace, mining, power generation, among others. The most usual method to set the wear rate is by measuring the mass loss of the material. In order to apply one technique with potential to determine the rate of erosion wear, this study developed a dedicated equipment and conducted preliminary erosion tests monitored by non-destructive testing known as acoustic emission technique (AE). This can be defined as a technique able to detect mechanical waves generated by the release of elastic energy accumulated in the material. Erosion tests were performed in order to evaluate the ability of equipment to collect data from AE and to correlate these data with the wear of the samples. Samples of low carbon steel eroded by the impact of angular aluminum oxide particles suspended in air at three different velocities: 45, 57 and 67 m/s. The impact angle between the particles and the sample was set at 30 degrees and the test temperature at approximately 20°C. The wear rate has changed with the velocity in accordance with the kinetic energy of the particles and the AE parameter RMS showed sensitivity to the variation of particle impact velocity and to the wear of the sample eroded. The rate of AE signals collected over time correlated with the flow of particles striking the sample, and with the parameters of energy, rise time and duration of the signal.

Jul 31, 2018

By Augusto César Barrios Tamayo

The high temperature erosion of Thermal Barrier Coatings (TBCs) is one of the main factors that define the lifespan in gas turbine components as it is considered the second source of failure of hot path components in power and propulsion turbine operation. The worn Top Coat (TC) surface in components such as first stage turbine blades affects the turbine efficiency due to energy losses and the increment in heat transfer to substrate. The first part of this work consists in describing a HTE test facility developed to emulate the damage conditions found in a number of components of gas turbines; in this testing machine, the samples were exposed to combustion gases moving at velocities close to 1.5 Mach and temperatures of 1100°C. The second part consists in the characterization of liners and first stage turbine blades of a GE7FA gas turbine used for power generation. The last part deal whit correlation of the features of TC’s worn surfaces with the erosion conditions and the dominant degradation mechanisms between test samples and turbine components were compared.

Jul 31, 2018

By Diego Berti Salvaro

The morphology, dimensions and chemical composition of tribolayers strongly depend on the pressures and temperatures acting on the contact. They are formed by reactions between the surfaces in contact with each other as well as with the atmosphere, lubricants and possible contaminants. In this paper the influence of test time (180, 500, 1000 and 2500 h) into the formation and characteristics of tribolayers in pairs DLC-stainless steel tested under refrigerant gas R134a atmosphere without presence of lubricating oil was analyzed. The characterization was performed using scanning electron microscopy, energy dispersive spectroscopy (SEM-EDS) (morphology and chemical composition) and white light interferometry (dimensions). The tribolayers thicknesses ranged from 100 to 500 nm and they were composed by elements originated from mutual transfers between the tribological pairs as well as oxides, being more pronounced on the stainless steel surface. The results show that the tribolayers are chemically stable (maintained the same composition over time) and the thickness remained stable after a thousand hours of testing.

Jul 31, 2018

By Humberto Tronconi Coelho

The use of friction dampers are wide proposed for a variety of mechanical systems for which it is not possible to apply viscoelastic materials, fluid based dampers or others viscous dampers. An important example is the application of friction dampers in aircraft engines to reduce the blades vibration amplitudes. In most cases, friction dampers have been studied in a passive way, however, a significant improvement can be achieved by controlling the normal force in the contact region. The aim of this paper is to study four control strategies for friction dampers based on three different hysteresis cycles. The first control strategy maximizes the energy removal in each harmonic oscillation cycle, by calculating the optimum normal force based on the last displacement peak. The second control strategy combines the first one with the maximum energy removal strategy used in the smart spring devices. Finally, is presented the strategy which homogenously modulates the friction force. Numerical studies were performed with these four strategies defining the performance metrics. The best control strategy was applied experimentally. The experimental test rig was fully identified and its parameters were used for numerical simulations. The obtained results have shown the good performance for the friction damper and selected strategy, also, the agreement between numerical and experimental results.

Jul 31, 2018

By Samuel de Lima Silva

A Comissão Interna de Conservação de Energia (CICE) atuou com uma série de ações para aprimorar a rotina de trabalho com finalidade da redução do consumo específico de gás natural na Unidade de Juiz de Fora da Votorantim Metais Zinco. As principais ações adotadas foram o desligamento de um dos queimadores da Caldeira Aalborg, e regulação do outro para 50%, utilizando o primeiro apenas quando necessário; estudo de melhorias na operação da Planta Polimetálicos, visando a redução de consumo pelo queimador do forno; melhoria no acompanhamento de consumo diário, tanto na chegada de gás quanto na caldeira; levantamento dos pontos de vazamento de vapor e contratação externa para adequação. Como resultado dessa série de ações tomadas, obtivemos uma redução de 17% no consumo específico de gás natural da planta.

Jul 31, 2018

By Nicolás Ariel Zabala

During the make-up and break-out of the connections, threaded joints are exposed to intense mechanical and tribological solicitations. The connection performance is influenced by its geometry, material properties, surface treatments and thread compound. The aim of this work is to evaluate and characterize the tribological behavior of different thread compounds applied on manganese phosphated carbon steel under low speed and high pressure sliding contact. Four thread compounds were evaluated: one containing lead, zinc and graphite; other lead-free, containing copper and finally, the last two lead-free and containing non-metallic solids. The tribological behavior was analyzed by a block-on-ring tribotest. During the test, load varied linearly between 250 N and 7000 N; loading and unloading lasted 14 sec and were performed in opposite directions of rotation to simulate the make-up and break-out operations. Friction force and load as a function of time were registered. Upon completion of the test, wear surfaces were analyzed by SEM, optical microscopy and energy dispersive spectroscopy. The obtained results show that the lead and zinc containing thread compound displayed the best behavior, showing a wear reduction of approximately 20%. These results are in line with previously known oilfield experience. Average COF values around 0.15 were measured and no significant differences between dopes were observed; indicating that the wear behavior was influenced by the additive package.

Jul 31, 2018

By Ronaldo Câmara Cozza

Iron aluminide alloy; Ball-cratering wear testing; Rolling abrasion; Wear volume; Coefficient of friction

Jul 31, 2018

By Kenneth Holmnerg

About 100 million terajoule is used annually worldwide to overcome friction and that is one fifth of all energy produced. The largest quantities of energy are used by industry (29%) and in transportation (27%). Based on our recent studies on energy use in passenger cars, trucks and buses, we concluded that it is possible to save as much as 17.5% of the energy use in road transports in the short term (5-9 years) by effective implementation of new tribological solutions. This equals to annual energy savings of 11.6 exajoules, fuel savings of 330 billion liters and reduction in CO2 emission by 860 million tonnes. In a paper mill, 15-25% of the energy used is spent to overcome friction. The electrical energy used by a paper machine is distributed as 32% to overcome friction, 36% for the paper production and mass transportation, and 32% is other losses. In paper machines, 11% of the total energy used to overcome friction can be saved by the implementation of new tribological technologies. This would result in electrical energy savings worldwide of 130,000 terajoule, economic cost savings of 2 billion euros and CO2 emission reduction of 11 million tonnes annually. An overview of the total energy saving potential by improved tribology in transportation and industry is presented.

Jul 31, 2018

By Eleir Mundim Bortoleto

A finite element modeling approach was developed to study adhesion phenomena during the unidirectional contact between a two-dimensional plane-strain square and a flat slab. Surfaces were metallic or ceramic, different pairs of materials were analyzed and their adhesion was considered by means of a FORTRAN subroutine (DLOAD), which was connected with commercial finite element code Abaqus and provided surface attractive forces based on the Lennard-Jones interatomic potential. Adhesive loads were considered both during approximation and separation of the surfaces. During the separation step, material transfer between surfaces, due to adhesion, was modeled by means of damage initiation and propagation at the flat slab. The parameters considered in the simulations were normal load, chemical affinity and system size and the different conditions were analyzed by comparison of the interaction forces during approach and withdrawal. This work also presents detailed descriptions of: (i) the evolution of energy dissipation due to adhesion hysteresis, (ii) the formation-growth-breakage of adhesive junctions and (iii) the evolution of stress distribution during the process. Results have indicated that chemical affinity between the bodies in contact is more relevant for adhesion than the applied load. Besides, smaller asperities are less prone to promote adhesive wear, but they may be subjected to high stress concentration effects.

Jul 31, 2018

By Qingwen Dai

The Marangoni effect is an important phenomenon where a surface tension gradient drives liquid towards high surface tension regions. Temperature gradient, evaporation, disparity of viscosity, and surface roughness and topography are all significant factors that can affect this thermo-capillary migration. The purpose of this study was to investigate the influence of micro-groove patterns on the migration of paraffin oil, and obtain a well-designed texture of micro-grooves to prevent the thermo-capillary migration. Patterns of micro-grooves with differing orientations and geometric parameters were fabricated on the surface of SUS 316 stainless steel substrates. Experiments on the migration behavior with different viscosities of paraffin oils were carried out various temperature gradients. The experimental phenomena indicated that the surface with the micro-grooves perpendicular or parallel to the temperature gradient have a strong impact on the migration performance of paraffin oil. Micro-grooves perpendicular to the temperature gradient exhibited extraordinary slower migration velocity than that of the parallel one. Width and depth of micro-grooves had an obvious influence on the behavior of temperature-driven migration and detail discussions on the effects of these geometric parameters were carried out.

Jul 31, 2018