Search Documents

By Farrel W. Lytle

An X-ray emission spectrographic method of analysis is presented for determining rare-earth elements in fractions obtained from bastnaesite ore. The method includes determination of yttrium, thorium, lanthanum, and the rare-earth elements in various complex mixtures. The analysis technique is based upon comparing the samples with synthetic standards approximating the composition of the samples. Working curves are plotted on an absolute-intensity basis, with no correction for back-ground. Examples of working curves and the analyses of typical rare-earth concentrates are included. The selection of spectral lines for the various sample matrices is discussed. A special technique is used for samples in which rapid hydration and carbonation occurred. By analyzing synthetic samples of known composition, the accuracy of the method was determined. The average error of analysis was about 3 percent of the amount present in the range from 5 to 100 percent and about 7 percent in the 0.2-to 5-percent range. A maximum of about 40 samples per day may be analyzed for 7 elements each.

Jan 1, 1957

By H. Hitchen

THE PURPOSE of this paper is to indicate the working capacity of different types of ropes for various engineering and mining duties. ROPE CONSTRUCTIONS There are approximately one hundred different designs of ropes in use today but, normally, only about ten are necessary for mining and engineering duties. The rest are designed for unusual equipments, or are different ways of combining wires of special shapes. Basically, the various designs of mining ropes consist of round, triangular, and oval strands, constructed with one or several layers of wire over a single wire, or a compound construction of sever.al wires. To suit different installations ropes are made with 3, 4, 5, or more of these types of strands over a central core, the ?co re itself being manufactured from either a fibrous material or a combination of steel wires. Nevertheless, in mining, the demand for 'locked coil rope', wl1ich may be considered as a single strand, is steadily increasing, especially for use on vertical shaft winding engines. So far as the locked coil rope is concerned, many constructions have been developed to suit different requirements, such as - in addition to winding ropes - aerial carrying Topes, shaft guide ropes and haulage ropes.

Jan 1, 1957

By H. D. Kessler, Joseph B. McAndrew

WHEN there is occasion to make structural use of metals at temperatures above 900°C (1652°F), the choice of alloys is severely limited, and those materials which meet special requirements as to density, strength, toughness, and resistance to creep, oxidation, or fatigue at such temperatures are at a premium. Any new type of high temperature alloy which is found to be outstanding with respect to several of these properties is therefore likely to find special applications for which it is uniquely advantageous as compared to other alloys. Such is the case with the 7 titanium-aluminum alloys. This y phase is an intermediate phase based on the composition TiAl, and extends from about 35.5 to 44.5 wt pct Al at temperatures up to 1000°C, above which the field broadens to include 60 pct A1 at 1340°C.' The alloys of principal interest have a narrow melting range, with 7 forming by the peri-tectic reaction, melt + ß=y at about 1460°C. Unlike most intermediate phases, the binary alloys containing titanium and aluminum in approximately equiatomic proportion possess low room temperature hardness,' in addition to which they have low density, good resistance to oxidation, and relatively high modulus of elasticity.' Unpublished work done at Armour Research Foundation showed

Jan 1, 1957

By H. E. Peterson

A study was undertaken by the Bureau of Mines to develop a simple, reliable test for field detection of selenium in rocks and soils. Two methods are described for qualitative detection of selenium, dependent upon its form of occurrence and the presence of interfering constituents in the sample. Both methods involve fusion of the sample in a test tube to form elemental selenium that will volatilize and condense as a red deposit on the cooler upper portion of the test tube. The methods are sensitive to 10 parts per million, (p.p.m.) equivalent to 0.001 percent, and can be made semiquantitative by using suitable standard samples. INTRODUCTION Although selenium is widely distributed in the United States, the known deposits are either so small or so low grade that they cannot be processed economically for selenium alone-4/ At present, commercial production is a byproduct of the smelting and refining of base-metal ores, particularly copper.5/ About 0.75 pound of selenium is recovered per ton of electrolytic copper, and small amounts are recovered by special treatment of assorted smelter dusts and fume products. Since selenium is a strategic metal in short supply, new sources are being sought by both Government and private interests.

Jan 1, 1957

By Milton E. Wadsworth, W. Martin Fassell, William H. Dresher

A study of the rate of dissolution of molybdenite (MoS2) in alkaline solution was carried out under carefully controlled conditions. Effects of temperature, oxygen over-pressure, and KOH concentration were evaluated. Studies were made in the temperature range 100°C to 175°C and in the pressure range 0 to 700 psia of oxygen. Under these conditions molybdenite was found to leach according to a linear mechanism. Both oxygen over-pressure and KOH concentration were found to control the rate of leaching. The mechanism has been explained in terms of adsorption of oxygen at the molybdenite surface followed by configurational rearrangement of the adsorbed molecules. The hydroxyl ion dependency is believed to be diffusion-controlled. Laboratory batch studies have shown that molybdenite can be readily dissolved in alkaline solutions under moderate conditions of temperature and pressure. Commercial application of this process to the production of ferro-molybdenum and molybdenum chemicals is promising in view of the ease of dissolution of molybdenite and the relatively noncorrosive conditions involved in the process. HIGH temperature-high pressure techniques have long been used to great advantage in the organic chemical industry, the petroleum industry, and the paper industry. Only recently, however, have these methods been used to extract metals from their ores on a commercial scale. The Chemical Construction Corp., together with interested producers of nickel and cobalt, has done much to develop methods of producing nickel and cobalt powders by the use of high temperature-high pressure techniques.' The Howe Sound Co. is currently operating a plant near Salt Lake City in which the new Chemical Construction Corp. technique is applied to cobalt-arsenic sulfide concentrates. In this method the concentrates are leached in a dilute solution of sulfuric acid under air pressure at a high temperature. Near Edmonton, in Alberta, Canada, the Sherritt Gordon Co. is also using the new method in conjunction with its ammoniacal leach process.' National Lead Co., at Fredricktown, Mo., is operating a process similar to that of Howe Sound. In spite of the rapid growth of high temperature-high pressure hydrometallurgical processes, there has been very little work done on fundamental principles involved in this type of process. Conse- quently the literature lacks any significant data in this field. Oxidation of pyrite,3 phalerite,4 galena,5 and recently molybdenite" in alkaline solutions has been reported to some extent. This investigation was initiated, therefore, to broaden the application of high temperature-high pressure hydrometallurgy and also to contribute some insight into the basic mechanisms of oxidation in an aqueous medium under these conditions. In addition to the immediate consequences of these processes much valuable information remains to be learned about fundamental reactions when they are carried out at temperatures and pressures slightly higher than those normally encountered. Leaching of molybdenite by alkaline solutions under oxygen pressure has recently been reported in the Russian literature by E. S. Usataya,8 who found that leaching rate increased with an increase in the pH of the solution—the strongest effects being observed at a pH of 10—and also with an increase in temperature. Usataya also has reported the formation of a protective film on the surface of the molybdenite when the leaching solution was weakly alkaline, neutral, or acidic. He believes that this oxidation process explains the migration of Mo+ + in the oxidation zones of molybdenite ore deposits and the subsequent impoverishment of the ores. Equipment: The high temperature-high pressure reaction unit used in this work was especially designed for kinetic studies of this nature, emphasis being placed on accuracy of measurement and precision of control. As details of the unit's construction and operation have been discussed elsewhere,7 Only basic features and principles of operation will be discussed at this point.

Jan 1, 1957

By C. S. Matthews, H. C. Lefkovits

The performance of depletion-type reservoirs at the stage in which the gas is at such low pressure that gravity is essentially the sole driving force has been investigated both theoretically and by use of scaled models. A simple theory is developed which completely explains the scaled model experiments. It also agrees with some field data. When the range of production rates to be considered is less than 25, the theory predicts that the production rate decline curve for homogeneous reservoirs in which there is a free surface will be of the hyperbolic type with n = 2: The theory gives a physical significance to the parameter y. INTRODUCTION This investigation was undertaken to determine a method for prediction of performance of reservoirs where gravity is the sole driving agent. Depletion-type reservoirs fall into this category after the pressure has fallen to some low value. Some examples of this type are found at Healdton ('Oklahoma), Oklahoma City (Oklahoma), Midway-Sunset (California), and East Coalinga (California). Generally the production rate per unit thickness is quite low in such reservoirs, with the conse- quence that this stage is sometimes called the stripper stage. However, per well production rates may be of the order of 50 B/D because of the considerable sand thickness open in some of the reservoirs. In the past, predictions of behavior of such reservoirs have been based on empirical extrapolation of the rate of production to the economic limit. Difficulties arise when new wells are drilled in the field or when production is artificially curtailed, since in such cases the decline rate of individual wells or leases changes and no clear trend can be detected. It was hoped that the present study would lead to improved methods for evaluation of such reservoirs. The study was initiated by building a scaled model for a particular field and by running a number of experiments on this model. Later a simple theory was developed which explained the laboratory results completely. The theory led, as shown below, to a hyperbolic-type decline equation which had been used previously' in a completely empirical manner. THEORY The General Case The problem to be treated here is the following: We are given a homogeneous cylindrical porous reservoir with exterior radius r, wellbore radius r., and height h,, containing, from the bottom up to a height hit oil, some gas, and interstitial water (see Fig. 1 A). The portion of the reservoir between K, and h, is filled with gas at low pressure, with residual oil, and with interstitial water. If at a time t = 0, the level of the oil in the wellbore is lowered to a height h,, what is the production rate from the reservoir at a time to The configuration within the reservoir at some instant

Jan 1, 1957

By R. P. Carreker

GERMANIUM is a member of that group of ele-nents—carbon, silicon, germanium, and tin-— that are currently of particular interest because of their interesting electrical properties. Near room temperature these materials of diamond cubic crystal structure are characteristically brittle. However, there have been several recent reports that germanium is not brittle at elevated temperatures These observations may be summarized as follows: 1—Germanium single crystals were observed to creep in bending under a maximum fiber stress of 6 kg per mm&apos; (8500 psi) at 500°C and above.&apos; The creep curves were sigmoidal, with an induction period that decreased with increasing temperature. 2—Germanium crystal bars have been bent 90" about radii ten times the bar thickness at 550°C.&apos; 3—-Audible clicks were heard when l/4 in. thick crystals were bent drastically at 450" to 500°C. No microstructural evidence of mechanical twinning was observed 4—Slip lines have been observed in tensile specimens deformed at 600°C, and are coincident with (111) planes, the close-packed planes of the diamond cubic structure.] The slip direction has not been established. 5—A germanium crystal has been compressed approximately 20 pct along a <110> axis at 700°C." The results reported subsequently were obtained in exploratory experiments intended to indicate some aspects of the behavior of germanium single crystals when tested in simple tension. Specimen Preparation A single crystal bar of n-type germanium was used. It was of purity corresponding to a resistance range of 2 to 20 ohm-cm. Tensile specimens were prepared by cutting small rectangular bars

Jan 1, 1957

By J. W. Marx

A method is given for predicting the complete gravity drainage characteristics of arbitrarily long columns from centrifuge drainage measurements on reconstituted core samples. Oil residuals corresponding to hundreds of years of normal gravity depletion can be obtained in a few hours on the centrifuge. The gravity flow rate at any stage of the depletion process may be determined from the time correlation derived, and experimentally checked, in this study. INTRODUCTION Apart from the original observations of Muskat et al1, research publications2,3,4 on the subject of gravity drainage have been largely concerned with establishing in detail the saturation, S as a function of the height, z, in a draining column at any given time, t. Some form of numerical integration must be employed to obtain production rates and cumulative production even when S(z, t) is known. Furthermore, the relevant experimental work has been concentrated on drainage of a single wetting liquid from unconsolidated media. Since oil production usually concerns the drainage of a partially wetting liquid from consolidated media, in the presence of connate water, and since it is unlikely that sufficient information exists to establish S(z, t) in detail for any natural reservoir, the published research work appears to be, at best, only qualitatively applicable to production problems. With this in mind, the present study was undertaken by the writer. Experiments were planned whose results would have two advantages over existing measurements: 1. Observations were to be made on specific reservoir rock, reconstituted with formation water and formation oil. This would reduce their generality, from the research viewpoint, but increase their utility for production purposes. 2. The measurements were to be self-integrating, i.e., the phenomena were to be described and interpreted in terms of cumulative results. THEORETICAL DEVELOPMENT It was commonly known that centrifuging a liquid bearing porous medium increases the drainage rates and minimizes capillary end effects. The specific problem lay in selecting an acceleration, a, such that the mean residual saturation of a model cylinder was equal to the residual saturation of an arbitrarily long prototype column when the latter was drained by earth gravity alone. The physical conditions required to permit a valid scaling of model drainage time, tm with prototype drainage time, t, may be stated as follows: (a) At t = tm = O, So = Smo; (b) At t = tm? 8 Sr. = Smr.; (c) For all intermediate values of t and dS/dt=dsm/dtm whenever S = Sm; (d) S(z) = Sm(z) = a constant when t = tm = 0. 1 Here S = T I S(z)dz, where h is the length of the « Jo cylindrical column being drained and the subscripts S,Sm, and refer to model, initial, and residual systems, respectively. The first three conditions mean, simply, that an 3 vs t plot will be numerically identical with an S, vs t, plot,

Jan 1, 1957

AMONG the features that make Inspiration of outstanding A interest, particularly to the engineer, is the fact that at various times it has used, as a major method of production, three more or less distinct methods of mining and three distinct methods of treating its ores. The following chronology is of interest : Major Mining Methods: 1915-194 7 Underground block-caving, exclusively 1948-1952 Underground block-caving and opencut mining 1953-1954 Underground block-caving, opencut mining, and "glory-hole caved-block transfer" mining 1955 on Opencut mining and "glory-hole caved-block transfer" mining. Major Ore Treatment Methods: 1915-1925 Flotation concentration exclusively 1926-1930 Flotation concentration and ferric sulphate leaching 1931-1955 Ferric sulphate leaching (the so-called "Dual Process" was used for eleven months in 1937 when demand for copper was phenomenal; and the "leach-float" process was used for 24 months in 1942-44 as an expedient to help meet war demands for copper). 1956 on "Dual Process" combining a sulphuric acid leach followed by fine grinding and flotation of the residue from the leaching vats.

Jan 1, 1957

IN CIRCLES where mining men are wont to fraternize, a statement often heard is: "Yes, I spent six (or two, or ten, or thirty) years down at &apos;Chuqui.&apos; " This means Chuquicamata, the site in Chile of what in all probability is the world&apos;s largest deposit of copper ore. One hears similar remarks regarding Braden and Andes, and, in fact, regarding a score of other big mines in South America, Africa, and elsewhere, but Chuqui seems to lead the others as the locale of engineers who have done a stint in foreign countries. One reason probably is that it is the Anaconda Company&apos;s premier foreign operation. Because of its unusual size and the diversity of its operations a great many men are needed. It is a sort of training school for young engineers; but, also, Anaconda has sent down a great many mature members of its big organization for special assignments like metallurgical research or plant construction. Chuquicamata is about 150 miles northeast of Antofagasta, at an elevation of 9,500 ft. It is in an almost rainless desert country where the wind (it is alleged by some) blows most of the time. However, the copper mining entrepreneurs have done their best to make up for what nature has neglected to do in creating a pleasant environment for the people who operate the mines. These include about 160 "foreigners" of whom 86 are from the United States, most of them accompanied by their families. There are 165 Chileans on the staff. Comforts, conveniences, and many luxuries are provided to offset in some measure the disagreeable features of the climate. Nevertheless, as I have implied, engineers at Chuqui generally jump at the chance to become "alumni" when opportunity offers. At the same time, they appear to take pride in their alma mater.

Jan 1, 1957

By D. T. Goettge, E. L. Robinson

The phase changes occurring in low carbon steel during hot strip mill rolling are shown to be metallurgically significant when related to commonly used temperature control points, particularly finishing and coiling temperatures. In combination, these temperatures are shown to have an important influence on the level and uniformity of hardness, grain size, and carbide characteristics of the finished hot and cold rolled sheets. PRODUCTION of wide flat-rolled products ordinarily requires a number of operations in sequence to prepare the material for shipment to the customer. Most products are tailor-made for specific end uses, with each operation contributing certain properties to the finished material. Since the characteristics imparted to the semifinished product by a given step in processing carry through to the finished product in varying degrees, it is important that the intermediate stages of production of flat-rolled strip be carried out with the same care which characterizes the last or finishing operations. The step of hot strip mill rolling is common to the production of all of the various types of flat-rolled product; therefore, the hot strip rolling is an especially important point at which to recognize and control those variables which have an effect on the surface characteristics and metallurgical properties of the finished product and which influence the ease of conducting subsequent operations. Orders entered at a producing mill usually show an end use or describe an article or part into which the ordered product is to be fabricated. Applying his experience as to the properties necessary in a finished sheet to suit the end use and to perform successfully in the fabrication involved, the metallurgist selects a steel of suitable composition and deoxidation practice, and slabs of appropriate dimensions are produced for rolling on the hot strip mill. At this stage of processing, the metallurgist faces the problem of controlling hot strip mill practice in the light of his diagnosis of the properties necessary to meet the end use, paying due attention to the accompanying problem of producing a strip which can meet processing requirements on subsequent units in the mill. It is the purpose of this paper to describe some of the factors which he must consider in solving these problems and to indicate some of the principles which guide him. Equipment, Physical Requirements of the Strip, and Temperature Measurement The metallurgist must, of course, be familiar with the physical layout of the mill, the temperature-measuring equipment available, and the physical requirements of the hot strip product before he can apply his metallurgical knowledge to the problem; hence, the first section will consist of a brief discussion of these matters. The usual hot strip mill consists of reheating furnaces, five or six roughing stands including a scale-breaker, holding table, and second scalebreaker, six-stand finishing mill, runout table with spray cooling facilities, and coilers. A schematic diagram of a typical layout is shown in Fig. 1. Slab temperatures are primarily a function of heating time and furnace temperatures, while mill speeds, spray practice, drafting practice, available water pressure, temperature of the cooling water, cross sectional dimensions of the strip, coil size, and equipment limitations, either singly or in combination, determine what rolling temperatures are practical on a given hot strip mill unit. Thus, it is possible that a set of temperatures which can be utilized successfully on one mill cannot be used on another. However, adjustments in temperatures and rolling practice can usually be made to develop the desired metallurgical properties. In addition to the metallurgical properties developed through proper temperature control, the hot strip mill must also provide strip with certain physical attributes which may be summarized as follows: Strip Cross Section—The strip contour should conform to a section which will give the best results in the cold reduction operation. This is generally recognized as a strip with 0.001 to 0.003 in. crown or shoulder-to-shoulder convexity depending on width, and freedom from concave, flat, or wedge-shaped cross sections which cause metal buildup in cold reduction. Excessive drop off in thickness at the edges can also be very detrimental in cold reducing to light gages. Gage, Width, and Camber—All of these must be controlled. For example, rundown or increasing thickness from the front to the back of the coil results in nonuniformity in the thickness of hot-rolled sheet product and in added difficulty with gage and welds in cold reduction. Similarly, excessive width variation is the cause of guide trouble and excessive edge scrap at later stages of processing, while excessive camber is the source of a variety of processing troubles. Type of Oxide—Product intended for pickling should have a predominance of the type of oxide most easily removable in sulfuric acid. It is generally recognized that this type is obtained by use of maximum table cooling water and cold coiling

Jan 1, 1957

By J. P. Zannaras

Referring to the article by R. J. Charles and P. L. de Bruyn, let us assume that W = weight of glass bar; P = weight of hammer; e = total deformation; K = unit of deformation; K = potential stress energy; E = modulus of elasticity; L = length of the bar; 7 = coefficient of inertia; h = height, ft; V = velocity, fps; and a = cross section area. The portion of kinetic energy which is effective in producing stress energy in a fixed bar struck horizontally is given by the formula" 1 + 1/3 W/P K =1+1/3w/p/(1+1/2w/p)2 P.V2/2g = Ph where 1 + 1/3 W/P ? (1 + 3W/P/(1=1/2w/p)2 [8] Putting e e = W/P =------------ From the above equation it can be seen that the maximum transfer of kinetic energy to stress energy is when e = 0 or W/P = 0 which indicates that the weight of the hammer must be very large as compared with the weight of the impacted rod. Eq. 8 diametrically opposes the conclusions reached by the authors of this article. In fact, if their suggestions were followed to the extreme when e = co when P = 0, there would be no transfer of kinetic energy to stress energy at all, as 7, becomes zero. Eq. 8 presumes that the velocity with which the stress is propagated through the bar is infinite, whereas the authors claim that the compression waves reflected are reaching the struck end of the bar prior to the complete transfer of the kinetic energy to cause such modification of the conditions there as to make them reach the reverse conclusions demonstrated by the above formula. That such interference exists is unquestionably demonstrated by the authors and others. However, if my observations are correct, such interference for this specific experiment and also for practical comminu- tion is insignificant, and the conclusions of the authors are in error and must be reversed to comply with Eq. 8. Eq. 5, w. = AE 2/2, given by the authors on page 51, is derived from the following equation (Eq. 9): K = 1/2Pe, where P = Sa, S = ?E, e = EL, and L = 1. The above formula, Eq. 9, cannot be applied in this case. This formula is applicable for static loads where the load increases from zero up to its final value, P, in such a way that the deformation at different instants is proportional to the loads acting at those instants and actually represents the area of a right triangle in the strain load diagram of base e and height P. The typical photographs shown in Figs. 3 and 4 represent the familiar strain load diagrams, and since the line of the wave marks the existence and intensity of the strain with the unquestionable conclusion that such strain has been caused by the action of a load acting continuously all along the wave until it reached the horizontal axis, the work stored at this point is represented by the area under the wave line and the horizontal axis and not by the area of the fictitious triangle given by the authors. Then if this is correct, even visual estimation of these areas at gage stations given in the typical photographs of Figs. 3 and 4 suffice to contradict the authors&apos; calculation given in Figs. 6a and 6b and Figs. 7a and 7b. The typical photographs presented by Charles and de Bruyn show a considerable variation of the intensity of the strain at different stations but very small variation of areas which actually represent the stress energy at the corresponding stations. And, apparently, by squaring the small quantities, the authors magnified their error tenfold. J. M. Frankland&apos;s paperV iscusses the relative strain intensity and not the total energy for different types of impact loading. He states in his paper, "The reader is explicitly warned not to confuse the results in this report with those obtained when the load is applied by a blow as from a hammer. In this case the peak load rises to very large but mostly unknown values. The accompanying large deflections and stresses are the result of high values of P, not of the dynamic load factor n. According to Frankland "the dynamic load factor" is the numerical maximum of the response factor. It therefore appears that the authors followed the same procedure in obtaining the relative strain energy ab-

Jan 1, 1957

By W. O. Philbrook, L. D. Kirkbride

IN the normal operation of the iron blast furnace, reduction of the iron oxides is accomplished almost entirely above the tuyeres.&apos; Blast furnace slags usually contain less than 0.5 pct FeO, although higher values may occur with abnormal operation. There is reason to conjecture, however, that incompletely reduced ore may sometimes reach the hearth and enter the slag as a result of heavy slips or, perhaps, even from cores of excessively large lumps of a charge material of poor reducibility. The possibility of reoxidation of iron droplets falling in front of the tuyeres has been considered by several writers. It would be of interest, to know how rapidly iron oxides reaching the slag for any of these reasons could be reduced by reaction with coke or with the high carbon liquid iron in the hearth. In comparison with the hundreds of papers that have appeared on various aspects of the reduction of solid iron oxides by gases and in the presence of several forms of carbon, little work has been published on the reductioin of liquid oxides or slags. Dancey measured rates of reaction of the pure liquid oxides, both FeO and Fe,O,, with molten iron containing about 4.3 pct C. The oxide was dropped into the cup formed in the upper surface of the iron by rotating the crucible and melt. Under these conditions, reduction of either FeO or Fe,O., was completed in less than 10 sec. The present study was concerned with the reduction of FeO from blast furnace-type slags containing less than 5 pct FeO and melted over carbon-saturated iron in stationary graphite crucibles. The results were considerably different from those found by Dancey, as will be discussed later. Although this work is of interest in relation to hearth reactions in the blast furnace, interpretations must be made with caution because the experimental conditions do not duplicate those within a furnace and may not even lead to the same reaction mechanism. The authors were motivated in undertaking this work by an additional interest—the part played by FeO reduction in the mechanism of de-sulphurization of iron by slags under similar experimental conditions. Derge, Philbrook, and Goldman eveloped detailed experimental evidence to support a three-step mechanism for desulphurization like that originally proposed by Holbrook and Joseph&apos; (These reactions are written in molecular form for convenience, but this is not intended to imply the existence of molecules of FeS in the bulk metal phase nor to deny the likelihood of ionic reactions in the slag.) Earlier work by Chang and Goldman" had shown that the overall reaction follows first-order kinetics with respect to sulphur and that the rate of reaction is proportional to the slag-metal interface area, which observations have been confirmed by subsequent work. Later studiese,&apos; have established the influence of al.loying elements on the first and last steps of the reaction. This paper reports a study of step 3 alone, uncomplicated by the simultaneous process of sulphur transfer. Apparatus and Procedure The experiments were made in a conventional high frequency induction furnace powered by a 35 kva Hg spark gap converter. The graphite crucibles used for most of the runs were 14 cm (5.5 in.) deep and 4.8 cm (1.9 in.) ID with 0.75 cm (0.3 in.) wall. An insulating cover with a small opening for withdrawing samples was used to minimize heat loss and infiltration of air into the furnace. The crucible was charged with 300 g of carbon-saturated iron and either 65 or 100 g of prefused slag analyzing 38.0 pct SiO,, 15.4 pct A10 and 47.1 pct CaO. To obtain the cleanest possible interface at the start of the reaction, the metal and slag were brought to temperature together to prevent the rejection of kish graphite that would have been caused by the chilling effect of a large addition of cold slag to carbon-saturated iron. After temperature control had been established, the desired amount of iron oxide was added in the form of a prefused slag of composition 73.6 pct FeO, 7.7 pct AWX and 19.0 pct SiOl. This slag addition was observed to be molten in somewhat less than 1 min, and a very vigorous reaction proceeded for 1 to 2 min after its introduction. Zero time was taken as 2 min after the ferrous silicate slag addition. Slag samples weighing about 0.5 g each were taken periodically by a copper chill sampler." The weight of the initial slag was large relative to the weight of samples removed, so that the slag weight never varied by more than 5 pct during any run. Temperature was measured by a calibrated W/Mo thermocouple immersed in the metal, with a graphite tip cemented over the fused silica protection tube to prevent attack by slag and metal. After some difficulties with uncertain temperatures during the first two runs, the practice adopted to position the thermocouple for reproducible results was to lower the protection tube to touch the bottom of the crucible and then raise it 0.5 cm. The apparent temperature gradient between the bottom of the crucible and the top of the slag was found to be 15°C (27°F). but much of this spread was probably the result of inadequate immersion of the protection tube to off-set conduction losses along the graphite tip when the thermocouple was inserted only into the slag. The temperature of the bath was controlled within 25°C (9°F) during a run.

Jan 1, 1957

By Stuart S. Forbes

Changes and additions made to the Canadian Copper Refiners Ltd. electrolytic refinery between 1949 and 1955 are reviewed. The effect of high current density on current efficiency and section work is discussed. OPERATING and physical changes which have been made to the electrolytic tank house of Canadian Copper Refiners Ltd. suggest a review of present conditions. Previous papers1 a have described the general arrangement. Since then, expansion, closer anode spacing, and higher current densities have increased annual cathode capacity from 112,000 to 182,000 tons. A recent extension to the tank house, begun in the spring of 1954 and completed in August 1955, was undertaken to handle the monthly production of about 3,000 tons of anodes from Gasp6 Copper Mines. The anticipation of these additional receipts and large stocks of unrefined copper caused by the increase in custom smelting at Noranda made it necessary to increase production without immediately available additional cell capacity. Accordingly, from December 1954 through March 1955, the tank house was operated successfully at a current density of 24.0 amp per sq ft. Again, as of September 1955, one of the two tank house circuits is being operated at this high density. Although other refineries may operate at current densities higher than 24 amp per sq ft, none is doing so with anodes which contain silver and gold content as high as those being refined at Canadian Copper Refiners Ltd. General Arrangement The original building consisted of two parallel bays, each 660 ft long and 60 ft wide, with a 24 ft pump bay extending along the west side of the building. A previous expansion, completed in 1939, was to the west of the original building and consisted of two 60 ft parallel bays 240 ft long. The length of these two bays was extended in 1954 to 540 ft, adding one stripper and 12 commercial sections to No. 2 electrical circuit. Space is still available for an additional six commercial sections and one stripper section. Construction on these seven sections started in September 1955, and will be completed early in 1956. The tank house capacity will then be 206,000 tons of cathodes per year. In the two tank houses there is a total of 900 cells distributed as follows—commercial, 468; stripper, 36; total, 504 in the No. 1 tank house (No. 1 circuit): commercial, 360; stripper, 36; total, 396 in the No. 2 tank house (No. 2 circuit). Section arrangement consists of nine cells to a tier and two tiers or 18 cells to a section. Anodes, weighing 620 lb each, are cast with a Baltimore groove and are refined by the multiple system. Solution enters each cell through a bottom inlet at one end and overflows at the top of the opposite end. Rate of solution flow through the cells is controlled by valves at each section to 4.5 gpm. Electrical power to the tank house is now provided by nine 675 kw motor generator sets. Each set consists of a 135-12 v 5000 amp dc generator, driven by a 980 hp 2300 v synchronous motor. When No. 1 circuit is operated at 22,000 amp, five sets, at 4400 amp each, are connected in parallel. As the maximum allowable current on No. 2 electrical circuit has recently been set at 18,000 amp, only four sets are connected in parallel on No. 2 circuit. A tenth set, now being installed, will be reserved as a spare, for use in either circuit as required. Recent Changes In 1949, the annual capacity of the tank house was increased from 112,000 to 132,000 tons by closing the

Jan 1, 1957

By R. D. Burlingame, T. L. Joseph, Gust Bitsianes

DESPITE almost fifty years of commercial practice, the sintering of iron ore has received little fundamental study. Much of the theoretical work1-&apos;has dealt with the constitution of sinter produced under widely varying conditions. While these studies have broadened our knowledge of the changes that occur in the sintering zone and in the freshly formed sinter during the early stages of cooling, they provide little insight into the changes that precede the formation of sinter. These preliminary changes merit study as a part of the overall process. Hessle. working with beds of Swedish magnetite concentrates, was one of the first investigators to study the sintering process in its entirety. On the basis of temperatures observed at various levels of the bed during sintering, he postulated a number of distinct reaction zones to account for the chemical changes leading to the formation of sinter. A more direct method of attack is that of arresting the sintering zone after it has progressed part way through the bed. A study of a vertical cross section through such a quenched bed provides direct information on the changes taking place at various levels. This method was used by McBriar et al.&apos; to show that several well-defined zones of chemical change existed within beds that were typical of British sintering practice. The same general method of attack was developed independently in the present investigation to study partially sintered beds typical of American practice. Experimental Sintering Equipment The sintering operation was carried out on an experimental scale with the equipment shown in Fig. 1. The refractory-walled sintering chamber A was 11 in. deep and averaged 9 in. in diameter. Air was introduced through a tapered flow section B, which contained the orifice C for accurate metering of the incoming air. This section was located directly above the square ignition housing D, which in turn rested upon the sintering chamber A. The bed was ignited with burner E. The required suction for the operation was furnished by a fan F, which had an air capacity of 500 cfm (stp). Hot exhaust gases from the sintering chamber were cleaned in the dustcatcher G before entering the exhaust fan. In the study of partially sintered beds, it was essential to find some technique for removing the entire charge from the sintering pot without disarranging the unsintered bottom portion. This problem was finally solved by sintering the charge in a removable basket, which snugly fitted the sintering chamber. This basket was constructed of two thicknesses of window screen and was lined with a 3/16-in. layer of asbestos paper. The bottom of the basket consisted of two thicknesses of wire screen, which were fastened to the basket wall. For high fuel mixtures, additional insulation was provided by a somewhat thicker layer of asbestos cement. Preparation of Partially Sintered Mixtures The moist feed was carefully placed in the sintering basket, to prevent segregation of the particles, which varied widely in size and composition. A thermocouple was placed in the center of the basket with the hot junction halfway down, and the mixture was evenly distributed around it. During ignition and throughout the sintering of the upper half of the bed, the hot junction temperature increased very little. When the sintering zone reached the halfway point, as indicated by the sudden increase in the hot junction temperature, the charge was quenched. During quenching the suction was turned off and the orifice was tightly stoppered to prevent further influx of air. At the same time, nitrogen was admitted to the sintering chamber through the orifice tap. As soon as the nitrogen had displaced the air and products of combustion, the charge was removed from the sintering pot for immediate dissection. It is impossible to preserve the exact zone structure of the bed at the instant that combustion is arrested unless the downward transmission of heat is also immediately stopped. Fortunately, heat transfer is very slow in beds containing a stationary fluid, especially if the particle size is small. It follows that the minimum quantity of nitrogen should be used to displace the air and that static conditions be established as soon as possible. A very steep temperature gradient across the combustion zone for some time after the quench was evidence of in-

Jan 1, 1957

By J. B. Gayle

A 1/2-ton experimental coke oven was installed ac the Bureau of Mines Southern Experiment Station, Tuscaloosa, Ala., in 1948. Designated as the Tuscaloosa oven, this unit features a 17-inch carbonizing chamber, globar heating elements, and silica-brick walls designed to simulate as closely as possible the carbonizing conditions for commercial slot-type ovens. Because of the small force exerted on the oven walls in most tests conducted to date (probably owing to the practice of charging coals and blends at a moisture content approximating that normal to commercial plants operating in this district), little information has been obtained about expansion properties. Two sole-heated ovens have therefore been constructed and used as supplementary equipment for determining the expansion properties of coals tested in the Tuscaloosa oven. The reasons for constructing the Tuscaloosa oven, the details of design, the operating, characteristics of the oven and the reproducibility of results have been discussed in previous publications. 3 4 5/ The present report deals with the effects of substituting various high- and low-volatile coals for components of a selected base blend carbonized under conditions similar to those normally used for producing foundry coke. Results of tests of 11 coals and 14 blends indicate that several blends tested rave cokes having physical properties very similar to those produced from the reference blend.

Jan 1, 1957

By R. A. Generes, H. C. H. Darley

Laboratory tests showed that at elevated temperatures a reaction takes place between all metal hydroxides and clay muds, which results in a thickening or solidifying of the mud, the extent of which depends on the nature of the ingredients. Calcium hydroxide gave the strongest solidification whereas barium hydroxide only caused a mild thickening, indicating that the use of barium hydroxide muds instead of lime muds would be a good way of preventing high-temperature solidification. It was found possible to prepare barium mud in the laboratory with caustic soda and a thinner in the same manner as lime muds, and these barium muds had the same or better toleration of high solids content, resistance to salt contamination, and low gel strengths as the corresponding lime muds. Three field trials have been made with barium mud. The principal difficulty encountered was in determining the correct proportions of the tourly treatments required to maintain low gel strengths. A satisfactory systern was finally developed, and low gels were maintained throughout the third test. The wells on which the trials were made were not carried deep enough to test the resistance to solidification adequately, but oven tests at 350°F were made periodically and no tendency to solidification was noted except immediately after severe cernent contamination had introduced excessive amounts of calcium into the system. Although barium hydroxide costs considerably more than lime, the total mud costs were as low, and on the last well significantly lower, than the average cost of lime mud wells drilled in the vicinity. INTRODUCTION The advantages of repressing dispersion and hydra-tion of clay cuttings carried in the mud, particularly when drilling through thick clay formations, are well recognized. This repression is generally achieved by the use of lime, and lime muds have in consequence the desirable characteristics of high toleration of solids, low thixotropy, and good resistance to contamination. They have, however, the disadvantage of high-temperature solidification. This phenomenon has been described in detail by Gray et al, who have shown that it is the result of a chemical reaction between the hydroxides and the clay minerals. The work described in this paper was undertaken to find a substitute for lime which would not cause this solidification. LABORATORY EXPERlMENTS The principal positive requirement for a substitute for lime is that it should repress the hydration and dispersion of clay. It is well known that monovalent cations promote hydration while polyvalent cations repress it. Therefore, a few representative polyvalent salts and hydroxides were tested to determine whether they could be used as substitutes for lime. Their efficiency at repressing hydration and dispersion was measured by means of the clay-volume test. It has been shown elsewhere&apos; that this test is a good measure of degree of dispersion of clay in suspension and that hydration accompanies and correlates with dispersion, so that measuring one measures the other. The test is made by centrifuging a 1:100 mixture of mud and 1-N NaCl and observing the volume of sediment—the greater the volume, the greater the dispersion. The tendency to caux solidification was measured by heating the muds in pressure vessels for 16 hours at 150°F and 370°F. An approximate quantitative

Jan 1, 1957

By H. W. Mossman

Three aspects of magnetite smelting are discussed. The first is the working out of equilibrium conditions for eliminating sulfur. The second is the influence of magnetite solubility on the difficulty of tapping the reverb matte. The third is an approximation of the equilibrium conditions in the reverb gases which govern whether magnetite is mode or reduced in the reverb slag by these gases and by any iron sulfide in the slag. MAGNETITE has had a varied history in the Hurley Smelter since its start in 1939. Magnetite determinations on the smelter products are made regularly only on the monthly composite samples. Variations on the monthly averages are shown in Table I. Magnetite which drops from the slag and matte in the reverb has some slight bottom buildup which comes and goes, but no substantial accumulation from this source has been found at the end of a normal nine months&apos; furnace campaign. However, there has been some low grade magnetite bearing material mixed with considerable A1,0,, which has slid down from the bottom of the sloping flue between the reverberatory furnace and the waste heat boilers. This accretion has required drilling and blasting near the skimming end of the furnace. The magnetite has interfered with tapping at times. When the smelter was first started, tapping trouble from magnetite was extremely severe. Increasing the reverberatory furnace temperature by putting in an air preheater and a Dutch oven has helped greatly, although there still is occasional tapping trouble. When the present series of physical chemistry articles on copper smelting started coming out in 1950, they were read with interest, but no immediate application was seen for them. Results of some laboratory work in 1952 aroused a much stronger interest in this physical chemistry. A series of melts was made on some converter slags, which had magnetite in very large grain sizes, with the object of reducing the grain sizes in the slag, as it was known that it was easier to handle in the reverb in that condition. Anything done in the tests greatly reduced the grain sizes—even in the controls, where nothing was done except melt the slag and cast it. There was more magnetite in the slags after the tests than before, and with wide variations. There were no obvious reasons lor much of what happened in these tests. Much of the base material published in English in this field was made available for study. Recalculations were made on many of the type problems, and part of the data was reduced to local temperatures and compositions. Explanations were found for what happened in the 1952 series of tests on converter slags, and the same principles turned out to be a description of much of what magnetite does in the reverb. This article is to present the results of that study, from the viewpoint of applying the technical material in definite numerical form to the operating conditions in both the converters and the reverberatory furnaces at the Hurley smelter. Table I. Magnetite Variations on Monthly Averages, 1939 to 1955 Pet Magnetite Lowest Highest Average Converter slag 13.6 43.3 25.4 Roverb slaa 2.7 20.9 8.7 Matte 28 15.9 98 In general it was found that magnetite is made or reduced in both the converters and the rever-beratory furnace, depending on variations of temperature, matte composition, and reverb gas composition occurring in ordinary plant operation. Within reasonable limits, the field conditions for formation or reduction can be predicted, and probably can be set up and maintained. Converter conditions affecting magnetite formation can be put into numerical values better than for the reverb from purely technical calculations. The converter can be operated so as to keep the magnetite in the slag down to between 12 and 14 pct and still give satisfactory life for the converter brick. This depends upon having converter flux available which will make a slag with a good separation without raising the temperature too high. In the Hurley reverb and others with similar conditions, it is likely that a compromise of conditions will give a reasonably good control of combustion and still keep the magnetite from building up on the bottom. This discussion consists of three main parts. The first is the working out of the equilibrium conditions in the converter for determining in which direction the reaction 3 Fe,,O, (s) + FeS (1) F? 10 FeO (1) + SO, will go under actual converter operating conditions. The second deals with the influence of the solubility of magnetite in the slag and matte in the reverb on the difficulty of tapping matte. The third is an approximation of the equilibrium conditions in the

Jan 1, 1957

By Robert G. Nisle

In conducting a pressure build-up test on an oil well, it is often necessary to shut-in the well for a short time prior to initiation of the test. The effect of such a short tern shut-in on the resulting pressure build-up curve is derived. The derivation is based on the Kelvin point-source solution and is a straight forward extension of the fundarnental theory. The magnitude of the effect is evaluatecl and illustrated by an example. It is shown that if the production subsequent to the short term shut-in is at least 10 times the duration of the shrct-in, the effect will he less than 10 per cent. INTRODUCTION It often happens that before a pressure build-up test can be made an additional valve must be mounted on the wellhead, or on arrival at the well, it might be learned that the well had been shut-in several hours the previous day because of a shortage of tankage. In such cases the question is How will such an interruption of production affect the results of a pressure buildup test This work explains how to take account of such a short term shut-in in order that the test can proceed without further delay. The solution presented here makes use of the Kelvin point-source solution used by Horne1 in his treatment of the pressure build-up in wells. Use is also made of the super-position theorem. MATHEMATICAL DERIVATION The well is assumed to have been in production at a constant rate for a relatively long time (several days or more). It is then shut-in for a short time, after which it is again placed in production at the previous constant rate. It continues to produce at this rate until shut-in for a pressure build-up test. The Kelvin point-source solution is expressed by Eq. 1. The sequence of production rates is listed in Table I. TABLE 1 — SEQUENCE OF PRODUCTION RATES Time interval Production Rate At time AT the pressure will be the resultant of the sequence of production rates shown in Table 1. An expression for the super-posed effects may be derived from this table. (Effect of + q for T + ? T) + (Effect of - q for T + ?T-t,) + (Effect of + q for T + ? T - t,) + (Effect of - q for ? T) = Resultant........(2) The desired result is obtained by substituting the effect defined by Eq. 1 for the terms in Eq. 2. The result is Eq. 3. When the logarithmic approximation is made for the exponential integrals and the terms collected the result is Eq. 4. Let T — t2 = T = flowing time following short term shut-in t2 — t1 = 6 = duration of short term shut-in Then T - t1 = r + 6 Substitution of these quantities in Eq. 4 gives p(rw ?T) = P,, -When d<<t - AT then d—&apos;-, T— approaches 1. r + AT In this case the effect of the short term shut-in may be ignored. In order to get some idea of the numerical magnitudes involved take the worst possible case, when AT = 0, that is at shut-in. If the error is made less than some maximum acceptable value at this time, it will be less than the maximum for all subsequent times. d + r Let the difference between the value of y-— and 1 be less than 0.1. Then —6+r — 1 < 0.1 S < O.l T Therefore, if the flowing time following a short term shut-in is at least 10 times the duration of the short term shut-in, the error introduced by ignoring the short term shut-in will not exceed 10 per cent of T+AT A T

Jan 1, 1957

By R. V. Lundquist

Aeration in water slurries and controlled drying of manganous hydroxide produced from dithionate leaching of Artillery Peak manganese ores from Arizona were investigated by the Bureau of Mines at its Electrometallurgical Experiment Station, Boulder City, Nev., to determine whether a simple process could be developed for converting this product into a battery-grade manganese dioxide. The properties of manganese dioxide prepared by the thermal decomposition of manganous nitrate were investigated also. Manganese dioxide suitable for use in batteries was not obtained from the dithionate leach product, but some of the factors controlling its oxidation were isolated. Aging of manganous hydroxide was of major importance in retarding its oxidation by aeration. Sodium hydroxide and sodium silicate promoted oxidation by drying. Optimum quantities were about 0.85 mol of sodium hydroxide and 0.2 mol of sodium silicate per mol of manganese, and drying temperatures of 200° C. produced yields of manganese dioxide up to 90 percent of the manganese present. Higher temperatures and concentrations of reagents carried oxidation of manganese beyond its tetravalent state.

Jan 1, 1957