Search Documents

By W. H. Tomlinson

One of the more important functions of the Federal Bureau of Mines is conservation of the life and health of employees of the mineral and allied industries. Since its very beginning the Bureau has encouraged competition between mine rescue and first-aid teams as a means of stimulating interest in safety and accident-prevention work. In addition to sponsoring competition on a national and international scale during the past 45 years, the Bureau has also assisted State mining departments, mining companies, and mining organizations in holding State, district, company, and other local meets. This assistance includes providing instructors to train teams, judges, and other contest officials. The Bureau has also furnished problems and outlines for working them, judges I discount sheets (scorecards), contest rules, and problem judges. In fact, Bureau representatives participate in nearly all State, district, and company contests and have bad complete charge of some contests.

Jan 1, 1956

By E. W. Cawthorne, R. I. Jaffee, C. M. Craighead

SOLUTION of a solid metal or alloy in a molten metal bath is used daily in melting operations, extractive metallurgical processes, and in brazing. It is generally recognized that temperature, time, agitation, and the composition of the solute metal and the solvent bath all affect solution rate. However, there is little information available in the literature on the kinetics of the process or the relative effect that these variables have on solution rate. In connection with an aluminum brazing study, data on the solution of aluminum in an A1-Si* bath to promote rapid solidification. The chemical analyses were made on drillings taken from the cast plates. The results of this work are listed in Table I. The thermal-analysis data were obtained on 200 gram samples cooled at approximately 1.5" per min. A calibrated chromel-alumel couple was used. The thermal arrests were recorded autographically on a General Electric photoelectric potentiometer recorder. The instrument was calibrated to 22.5 pct. The thermal emf was bucked with a Leeds and Northrup semiprecision potentiometer so that 1 mv represented the full scale of the GE recorder. Referring to Table I, it will be noted that the analytical results tend to be lower than the intended compositions by about 0.3 pct Si in the higher ranges. In view of the known difficulties in obtaining accurate silicon determinations by wet analysis when the silicon content is high and in view of the care that was employed in weighing and preparing the alloys, the intended compositions are believed to be more accurate than the analyses. Furthermore, when the thermal-arrest data are plotted against the intended compositions, a smooth curve is obtained, as shown in Fig. 1. This is not the case when the data are plotted against the analytical results. It will be noted from Table I that the 12.5 pct Si alloy (melt 4) showed a primary arrest at 577.6"C and the eutectic at 576.l°C. The metallographic examination of this chill-cast plate sample showed a small amount of primary silicon. These results, Fig. 1, place the eutectic at slightly less than 12.5 pct Si and are in rather good agreement with the unpublished Hanford data. In all of the subsequent work, the composition of the A1-Si dipping baths was determined by thermal analysis (spread between the primary arrest and the eutectic temperature) employing 12.5 pct Si and 577.2 °C as the composition and temperature of the eutectic. Material Preparation and Selection of the Techniques: At the beginning of this work, it was anticipated that, owing to oxide film present on the surface of the aluminum, difficulty would be encountered in obtaining rapid uniform wetting of aluminum specimens dipped in the A1-Si bath. The following etchants were investigated as possible methods of providing a thin uniform oxide film on the specimen surface: 1—phosphoric acid (H³O4), 2—fluoboric acid (HBFI), 3—sodium hydroxide (NaOH), and 4—hydrofluoric acid (HF). Tests with sheet .specimens (2x½x0.06 in.) of 2s aluminum prepared with these etchants indicated that the fast uniform wetting required for this work could not be obtained if any oxide film existed on the specimen surface. Tests were then conducted by dipping similar specimens etched in 5 pct NaOH and given a thin

Jan 1, 1956

By A. Brown

IN INTRODUCING the subject of rock pressures, it may safely be assumed that mining men are only too familiar with the physical effects of strata stresses that accompany the extraction of minerals. It may be further assumed that they have, as individuals, arrived at certain conclusions regarding their nature, based upon years spent in observing such phenomena and in learning how to continue mining in spite of them. Such hardly won experience forms the core of what is often referred to as 'pit sense'. This essential type of knowledge is not ?based on theoretical considerations, nor can it be found in text books. It is highly individualistic in nature and almost impossible to pass on from one generation to another in terms of precise rules for guidance. It is this aspect of individual judgment based on practical experience that has led to the significant phrase The Art of Mining.

Jan 1, 1956

By R. A. Beall

This paper summarizes the development of a furnace for producing titanium castings. The general problem is outlined and chronological details are given on the construction and operation of four different casting furnaces, all utilizing consumable-electrode arc heating and water-cooled copper crucibles. Of the two methods of pouring, the tilt-pour technique has been more satisfactory than bottom tapping. Mold design, electrode fabrication, and deep-pool production are discussed. INTRODUCTION In the early summer of 1953 the Bureau of Mines was contacted by the Department of the Army through Watertown Arsenal to explore the possibility of conducting research on casting titanium metal. The objective of the program was "to develop a technique for producing formed castings of titanium metal not less than 40 pounds in weight and without introduction of deleterious contamination."

Jan 1, 1956

By J. J. Hoeppner

Accurate determination of moisture in coals of various ranks has long been a subject of intensive investigation. Excellent reviews of methods developed over many years are given by Brown (9)4/ and, with experimental comparisons, by Goodman, Gomez, and Parry (11). As pointed out in these and other writings, one of the principal difficulties in assigning absolute merit to one or another procedure is the multiplicity of conditions under which water may exist in coal and the difficulties involved in obtaining sharp separation and distinction between these classes. Gauger (10) states: Water recoverable from coal is obtained from the following sources: (1) Decomposition of organic molecules (sometimes called combined water), (2) surface adsorbed water, (3) capillary condensed water, (4) dissolved water, and (5) water of hydration of inorganic constituents of the coal.

Jan 1, 1956

By P. D. S. St. Pierre

IN REGENT YEARS, blast furnace operators have found it necessary to improve their technology in order to handle increasingly low-grade feed and yet satisfy the demands for greater tonnages of metal. Studies have been made covering several aspects of the problem, and in this connection the slags produced in the iron-making process have been critically examined with a view to discovering the slag with the optimum properties for a given operation. A good slag should combine, as far as possible, the properties listed in Table I. Unfortunately, some of these desirable properties are incompatible. For example, the advantage of the small ?bulk of a low-flux slag is offset by its low desulphurization potential and high viscosity. Similarly, a very fluid slag increases refractory wear. It will be seen, then, that a balance must he struck between these conflicting requirements. In the .present paper only the melting relationships of blast furnace slag ?compositions will be considered in detail. In interpreting the data herein presented, the optimum property requirements listed in Table 1 must strictly be borne in mind. It should also be noted that the discussion presented here always relates to calcined fluxes, since this facilitates reference to the final slag composition. Thus, in making calculations pertaining to the ?burdening of the furnace, due allowance should ?be made for the fact that the fluxes are added as carbonates.

Jan 1, 1956

By C. S. Matthews, W. R. Strickler, M. Prats

To gain an insight into the deviations from normal behavior caused by dip. a mathematical study has been made of single-fluid five-spot floods in dipping reservoirs for flooding techniques likely to be employed in such cases. Streamline patterns and sweep eficiencies are computed for a number of different cases, and the results, where possible, are presented in graphical form. An increase in sweep efficiency can be obtained by moving the central injection well updip, and the opti~num position is found for several cases. The applicnhility of the results is discussed. INTRODUCTION Because of the growing importance of water flooding in California and in other locations where large angles of dip are quite common, it is important to know at least some of the effects of dip on the performance characteristics of water floods in such instances. In the past, only reservoirs having relatively mild dips have been wateflooded. Consequently, little is known today as to the effect of dip on the performance characteristics of a flooding operation from the point of view of field experience; and because of the complexity of the problem, little, if anything, has been done on the problem from the point of view of theory. There are two distinct aspects of the role played by gravity in a flooding operation. The first is that of the preferential segregation of the reservoir fluids at the time when the flood is to commence. The second is the role that it may play in affecting the performance of the reservoir during the course of the flooding operation. In this paper the reservoir is assumed to be filled with only one fluid, so that there is no preferential segregation of reservoir fluids at the commencement of the flood. Moreover, the injected and in-place fluids are assumed to have the same characteristics, so that in effect we consider only a single-fluid problem. Single-fluid results have been used as a guide in the past for predicting and interpreting the behavior of regular five-spot floods in horizontal reservoirs. It is thought that single-fluid results might likewise be used for five-spot patterns in dipping reservoirs as a norm to which the effects of the multifluid problems might he referred.* In confining our attention to the single-fluid case, we therefore do not consider the preferential segregation of injected water in the oil bank, or of the oil bank in the unflooded zone. Instead we consider the deviation from the behavior of a horizontal five-spot which is caused by use of flooding techniques (i.e., the flow potential pattern at injection and production wells) likely to be employed during flooding operations in dipping reservoirs. In other words, we consider effects which are caused by the pattern of injection and production well pressures which we choose to apply. Performance characteristics are given for the five-spot spacing pattern as a function of two parameters; one is the ratio of gravity head to potential difference bctwccn the high updip injection well and the low downdip producer of the same five-spot, denoted by Rg; the second is the orientation of the five-spot pat-

Jan 1, 1956

By Irving Hartmann

Modern mechanized mining with high-speed machines, multiple-entry systems, multiple blasting, high-velocity air currents, and rapid haulage has brought many economic benefits and has on the whole enhanced safety in the coal-mining industry. It has, however, also introduced some added hazards, the control of which requires concerted effort and ingenuity. Mechanized mining has greatly increased the production and dissemination of fine coal seam or in mine entries. Use of high-speed machines has increased the probability of formation of incendive sparks, which are produced by frictional contact between moving metals and certain mineral substances in the coal seam or in the adjoining rock strata. In gassy seams rapid extraction of coal has increased the rate of gas evolution. These facts have made more urgent the need of preventing the ignition of coal dust and the development of widespread mine explosions. The ignition hazard can be controlled best by eliminating all potential igniting sources and by careful attention to ventilation designed to prevent accumulation of gas capable of triggering a coal-dust explosion. Frictional spark ignition by mining machines and suggested safeguards are discussed in a recent publication. Extensive research and long experience have shown conclusively that the propagation of coal-dust flames can be arrested and the development of widespread explosions prevented by properly applied, generalized rock dusting.

Jan 1, 1956

By R. G. Travis

1. Reserve estimates have been made for eight coal beds in Monongalia County, W. Va., but only the Pittsburgh, Sewickley, and Upper Freeport beds are important at this time. The Pittsburgh, Sewickley, Waynesburg, and Upper Freeport beds contain the largest recoverable reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 3,526 million tons as of January 1, 1954. Of this total, 3,294 mil-lion tons is in beds 28 inches and more thick. Areas in each bed except the Pittsburgh were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By L. D. Jaffe

From the limited experimental data in the literature, preliminary values were derived for the thermal diffusivity of titanium alloys and for the quenching severity of various mediums used in heat treating them. The thermal diffusivity, under quenching conditions, was found to be approximately 0.006 sq in. per sec. The quenching severity H for brine is approximately 8, for water 4, for oil 0.9, for air 0.08, and for argon 0.02 in. -' The quenching severity of the Jominy-Boegehold end quench water jet against titanium alloys appeared effectively infinite. Using these results, graphs were prepared showing ideal round sizes and Jominy positions having cooled conditions equivalent to those at the center and surface of titanium alloy rounds, plates, and sheets quenched in various media. THE importance of proper quenching of steel parts has long been recognized, and much quantitative work has been done on the subject. Recently, it has become evident that for titanium alloys, too, the rate of cooling from high temperature is important in obtaining high strength and hardness. Maximum hardness and strength may not be attained in the as-quenched condition but rather after a subsequent tempering or aging treatment. Nevertheless, if cooling from temperatures near the ß transus is too slow, for the hardenability of the alloy used, a soft a-ß structure will be produced which will not harden on subsequent aging.'-" The quenching of parts of practical interest can usually be approximated by simple shapes, such as cylinders (rounds) and plates (or sheets) of various thickness and combinations of these. A standard that has been used extensively for comparison purposes is the center of an ideal round: a cylinder quenched in a medium that instantly cools its surface to room temperature." For steel, considerable practical use has been made of the Jominy-Boegehold end quench hardenability specimen,".' and its value for titanium alloys is becoming evident. It therefore appeared worthwhile to attempt comparison of cooling conditions in titanium alloy rounds and plates of various sizes quenched in various media with cooling conditions in ideal round and Jominy quenches. These comparisons are based upon measurements reported in the literature. Quenching Severity of Jominy Water Jet and of Brine As one starting point, there were available the data of Phillips and Tobin8 for positions on a Jominy specimen having the same hardness as the centers of round bars of various size quenched in 5 pct NaOH brine, shown in Table I. The Jominy speci- men is a round bar, normally 1 in. diam and 4 in. long, quenched by a water jet at one end and air cooled on the other surfaces.' After quenching, hardness is measured vs distance from the quenched end on longitudinal flats ground 0.015 to 0.10 in. deep. The data of Table I were based on a subsized specimen of 3/4 in. diam. Since the positions tested are close to the jet quenched end, cooling there may be taken as due solely to the jet, and air cooling can be neglected. These positions are then equivalent to various locations near one surface of an 8 in. plate jet quenched on both sides. Assuming that the thermal diffusivity is constant and that Newton's law of cooling holds, temperature vs time curves at corresponding positions in Jominy specimen and round bar then may be calculated for various assumed quenching severities of the water jet and of the brine. Cooling curves are generally taken to be metallurgically equivalent when they show the same time to reach a temperature halfway between the initial (heat treating) temperature and the final (quenching medium) temperature.5 On this basis, using Russell's tables,9 upplemented by heat flow tables derived in similar fashion by the author for positions near the surface of severely quenched plates, it was found that the experimentally observed equivalence, Table I, was best matched if the quenching severity H of the Jominy water jet was taken as infinite (H = co). This means that the jet quenched surface should be considered as instantly cooled to the temperature of the water

Jan 1, 1956

By J. C. Barrett

Bureau of Mines research on the arc welding characteristics of titanium was initiated in 1948. Little was known about the art except that the easily contaminated metal required more protection from the atmosphere during welding than most other metals. Chambers were designed and built within which titanium could be welded with adequate inert gas protection. Welds were made and their properties studied, and prototype items were made successfully. This report, presenting a resume of the titanium arc-welding experiments undertaken by the Bureau of Mines, demonstrates that the process is successful if conducted under proper conditions and describes the welding of prototypes. INTRODUCTION The Bureau of Mines' first report on methods of joining titanium covered the subject of spot welding,4/ outlining the conditions necessary for producing spot welds in ductile titanium consolidated by powder metallurgy methods and describing the characteristics of such welds. This report embraces the field of fusion weld-ing of titanium and traces the development of suitable methods and equipment for producing such welds.

Jan 1, 1956

By Lloyd Williams

1. The investigation shows that the Coal Creek has been the most productive, bed in Campbell County and contains the largest recoverable reserves of coal. The Pewee, Red Ash, and Jullico have been relatively productive beds and contain appreciable recoverable reserves of coal. The Blue Gem also has been productive in the past, but available information indicates that most of the remaining coal is Less than 28 inches thick. The Big Mary has relatively large reserves over 28 inches thick, but the coal is high in ash and sulfur. Thick partings in the Windrock bed have discouraged mining in that bed. The Poplar Creek and Rex beds generally are below drainage, and large areas have been excluded from the reserve estimate, Reserves in the Walnut Mountain bed will be difficult to mine due to the irregu¬lar thickness and lack of continuity of the bed. Estimated coal reserves are- small in the remaining five beds. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-Foot of coal in place, are estimated to be 398 million tons as of January 1, 1953, o? this total, 267 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, these should be added to the total estimated reserves.

Jan 1, 1956

By Oliver Bowles

From remote antiquity stone has been employed for structural, ornamental, and memorial purposes. It was, and still is, so used because of its availability in innumerable localities and its architectural adaptability, dignity, substantiality, and durability. The principal varieties of stone used are granite, marble, limestone, sandstone, and slate. This report deals with granite. OCCURRENCE AND CHARACTER OF GRANITE Granites usually have been classed as igneous rocks derived from molten masses or magmas, but there is wide evidence that the origin of some granites may be attributed to regional metamorphism of preexisting rocks, rearrangement and recrystallization taking place without a liquid or molten stage. In any event granitization is a slow, deep-seated process.

Jan 1, 1956

By A. J. Barry

To determine the torque-load relationship for SIB-inch (nominal)-diameter roof bolts, the Bureau of Mines tested 5 makes of expansion shells and 2 types of bolts (regular and high-strength) in 2 sandstone and 2 shale mine roofs. Unused flat-steel bearing plates in as-received condition were used in these tests. The relationship between torque and load was found to be approximately 50 pounds of load per foot-pound of torque for both the regular and high-strength bolts. This relationship is valid up to 130 foot-pounds for the regular bolts and up to 175 foot-pounds for the high-strength bolts. A torque of 130 foot-pounds on a regular bolt will produce a load of 6,150 ± 1,910 pounds 90 percent of the time, and a torque of 175 foot-pounds on a high-strength bolt will produce 8,050 ± 2,750 pounds 90 percent of the time. Above these values, the torque-load relationship tends to be erratic due to binding between the bolt and plug threads. Binding causes excessive torque to be expended in producing torsion in the bolt rather than tension. This torsion adversely affects the yield load of the bolt. Therefore, the installed torques should not exceed the 130-and l75-foot-pound values. A statistical analysis of the data showed that the torque-load relationship was not significantly affected by the type of bolt or expansion shell unit but might have been affected by the type of rock.

Jan 1, 1956

By A. O. Dufresne

WITHOUT transportation, mining would be quite impossible. Any person familiar with the operation of a mine knows full well that from the minute ore is blasted, it is kept moving until it reaches the treatment plant. In the mill, by means of conveyors and elevators, the ore is brought from receiving bins to one machine after another until finally its valuable mineral is separated from the gangue. The finished product must then be shipped -either by boat, rail, or motor trucks to industrial centres, where it undergoes further treatment and transformation into finished commercial goods. Everybody appreciates that the winning of an or-e includes, amongst various operations, the moving of large quantities of material of generally low value. Transportation, therefore, must be considered One of the most important factors in the economics of mining. My assignment, this afternoon, is not to treat of that phase of transportation as it directly affects mining operations, but rather to consider some of the aspects of overland transportation and its influence in bringing about the development of mining camps in Canada. I shall take the liberty of rapidly surveying conditions facing prospectors, mine developers and operators from the time a region is still in a pre-pioneering stage until such time as a mine starts shipping its concentrates.

Jan 1, 1956

By Ralph V. Higgins

The present methods of appraising the long-range performance of oil reservoirs are based upon physical properties of the crude oil and the permeability of the reservoir rock. By means of these methods the performance of a reservoir may be estimated throughout its entire life. Before these methods were used, the future performance was estimated mostly by extrapolating pressure-decline curves -a method that is satisfactory for extrapolating only for a short period into the future. One factor that affects satisfactory long-range prediction of reservoir performance is the extent to which small changes in the physical properties of the oil and differences in the choices of relative permeability influence the calculated oil recovery. Selection of the physical properties of the samples to represent those of the oil and rock for the entire reservoir is difficult. This report is concerned with the error in calculated recoveries that may result from these inherent difficulties.

Jan 1, 1956

By R. R. McLellan

The Brown Derby pegmatites are in Gunnison County, Colo., about 18 miles east of Gunnison. Approximately 860 tons of lepidolite concentrates, with smaller amounts of microlite and beryl, was produced from 3 dikes of the Brown Derby group from 1943 through 1947. No mining was done from 1948 until December 1950, when production of lepidolite and beryl was resumed by the Poston Mining & Milling Co. Mining was intermittent during 1951 and 1952. The dikes were mapped and studied by the Federal Geological Survey during the field seasons of 1942 to 1944, and in May 1950 the Bureau of Mines initiated a diamond-drilling project to test the three dikes for lepidolite and beryl. After being recessed twice, the project was terminated indefinitely July 1951. Seven drill holes were completed for a total of 1,841.6 feet of drilling.

Jan 1, 1956

By Manuel Gomez

A lignite from Milam County, Tex., has been oxidized by air at temperatures from about 27° to 300° C. for varying lengths of time. The oxidized coal was carbonized at 500° C. in a laboratory assay unit, and the products of carbonization were measured and analyzed. The data presented suggest that, as lignite is progressively oxidized, tar yields are decreased and gas yields are increased in a ratio approximating 1:1. It is surmised that tar-yielding structures in the nonoxidized coal produce gas, principally, when the coal is oxidized. Char-yielding structures of the nonoxidized coal give rise to additional water of decomposition after oxidation and pyrolysis. As lignite is subjected to greater oxidation, the gaseous product evolved on pyrolysis becomes almost entirely carbon dioxide. Tar yields decrease with an increased degree of oxidation, so that the reduction in tar yield may be used as a qualitative measure of oxidation. Pilot-plant drying and carbonization, where air is used as the transport gas and where some air is included in the drying and carbonizing gases, induces some oxidation of the coal particle. The short residence time in a fluidized system with reference to the oxidation environment limits the oxidation.

Jan 1, 1956

By E. G. Erspamer

Laboratory investigations were made by the Bureau of Mines on ore containing the sulfides of both mercury and antimony to develop a method or methods for the economic recovery of mercury metal and the concurrent recovery of antimony as metal or salts,. If standard mercury-recovery techniques are applied to such ores, the antimony content interferes with the effective production of mercury metal; further-more, the antimony is lost. This report presents the results of tests on a sample of cinnabar-stibnite ore from the Red Devil mine near Sleitmute, Alaska. Red Devil ore was chosen for the investigation because it is purported to be typical of ores of the Kuskokwim River area, which, in their aggregate, constitute large potential reserves of mercury and antimony. Studies included petrographic, spectrographic, and chemical analyses, gravity-separation tests, bulk flotation of mercury and antimony sulfides, differential flotation, leaching, and furnacing of crude ore and of flotation concentrate.

Jan 1, 1956

By E. W. Stewart, G. P. Conard, J. F. Libsch

The effects of several additives upon the reduction characteristics of hydrogen-reduced ferrous formate are described. The various additives inhibit sintering of the reduced iron particles by apparently different mechanisms. The magnetic properties of the low density compacts produced from the resulting ultra-fine iron powders were improved markedly. THE permanent magnetic characteristics of ultra-fine iron powder prepared by various means have been a subject of considerable interest and experimentation in the past few years. When such particles are small enough to show single domain behavior, they possess' 1—permanent saturation magnetization, and 2—high coercive force. In the absence of domain boundaries, the only magnetization changes in a particle occur through spin rotation which is opposed by relatively large anisotropy forces. With decreasing particle size, the coercive force tends to increase to a maximum and then decrease because of the instability in magnetization associated with thermal fluctuations. Kittel' has calculated the critical diameter at which a spherical particle of iron can no longer sustain domain boundaries or walls to be approximately 1.5x10-' cm. Stoner and Wohlfarthr in England and Neel4,6 in France have shown from purely theoretical calculations that the high coercive force expected from single domain particles is dependent upon crystal anisotropy, shape anisotropy, or strain anisotropy contributions. Further work by Weil, Bertaut,' and many others has contributed much to the understanding of fine particle theory. Neel and Meikeljohn" have demonstrated that a decrease in particle size below a critical value of approximately 160A leads to a quite rapid decrease in coercive force because of the prevention of stable magnetization by thermal agitation. Lih1, working with powders prepared by the reduction of formate and oxalate salts of iron, has shown the marked influence of powder purity upon magnetic properties. Maximum coercive force was obtained in powders of approximately 65 pct metallic iron content while the maximum energy product, (BxH) occurred in powders of 85 pct metallic iron content. Careful consideration of the preceding theoretical considerations and experimental results has led to the manufacture of permanent magnets from ultra-fine ferromagnetic powders by powder metallurgy techniques. Such work has been done by Dean and Davis," the Ugine Co. of France, and Kopelman." The aforementioned work of Kopelman and the Ugine Co. was concerned somewhat with the effect of various additives upon the properties of hydrogen-reduced ferrous formate. Virtually no work, however, has been published on the effects of additives on the reduction rates of metal formates, although unpublished work by Ananthanarayanan16 howed promise of improved energy product in ultra-fine iron compacts prepared by the hydrogen reduction of a coprecipitated mixture of magnesium and ferrous formate. After consideration of the preceding information, it was hoped that a better balance between the metallic iron content and particle size of the reduced iron powder could be accomplished by a prevention of the attendant sintering of the partially reduced iron powder during the reduction reaction. It appeared possible that magnesium oxide might interpose a mechanical barrier between adjacent iron particles and prevent their sintering together, while metallic cadmium and metallic tin would interpose a liquid barrier which might accomplish the same purpose. The degree to which these materials were effective in accomplishing the foregoing objective and the experimental details associated with the work are reported in the following sections of this paper. Experimental Procedure Preparation of Formate and Oxide Mixtures: To obtain ferrous formate of reproducible reduction characteristics, a slight modification' was made in the technique of Fraioli and Rhoda." A supersaturated solution of ferrous formate was mixed with an equal volume of 95 pct ethyl alcohol and the formate crystals precipitated by stirring and screened to —325 mesh. These crystals were in the shape of elongated hexagons, approximately 4x10 micron in dimension. Various preparations of such ferrous formate, designated as lot 111, were reduced for 2 hr, yielding ultra-fine iron particles of exceedingly reproducible size, metallic iron content, and magnetic properties. The magnesium and cadmium formates were prepared by the reaction of dilute formic acid with their respective carbonates, while the tin formate was prepared by the reaction of dilute formic acid with stannous hydroxide. To evaluate the effect of metallic formate additives in intimate mixture with the ferrous formate, varying amounts of magnesium, cadmium, and tin formates were coprecipitated with the latter. The designations of these materials and their chemical compositions are given in Table I. Due to the differing solubilities of the various formates in aqueous media,

Jan 1, 1956