Search Documents

By D. J. Bourne, G. E. Atwood

The new potash refinery of Duval Sulphur & Potash Co. produced its first tonnage of muriate of potash in November 1951. Full capacity was attained in early 1952. Excellent extraction efficiency is being obtained by the process, which is basically froth flotation. System temperature control is practiced and has proved to be of great metallurgical value through high potassium recovery and. low reagent cost. WHEN Duval Sulphur and Potash Co. recently entered the established potash industry, the vast amount of pioneer work essential in an entirely new endeavor was unnecessary. Thus it was possible to screen and assemble proved techniques into a highly efficient process based on the combined knowledge of the industry. It is hoped that the refinements Duval has added to these cumulative achievements will contribute to the rapid advance of the potash industry and related enterprises. The process selected utilizes as raw material syl-vinite ore typical of the Permian Basin. This ore is principally comprised of interlocked crystals of potassium chloride, about 40 pct, and sodium chloride. Also there is as much as 1 1/2 pct of dispersed clay slime which, because of its nature, highly complicates beneficiation of these ores. The refining method is basically flotation in which the mineral sylvite is floated away from the halite-clay gangue to produce a 60 pct K,O muriate of potash product for the plant-food trade. It departs from established practice in the use of an improved reagent scheme, developed by the company's technical staff, and in

Jan 1, 1954

By L. Himmel, R. F. Mehl, C. E. Birchenall

The rates of self-diffusion of iron in artifically prepared wustites of various compositions have been determined using the decrease in surface activity technique. Similar measurements are reported for artificial magnetites of nearly stoichiometric composition and for natural hematite single crystals. These data, together with appropriate thermodynamic data derived from the present study or from the literature, are used to calculate the rates of oxidation of iron and its oxides, taking as a basis the theoretical rate equations developed by Wagner. The calculations are compared with experimental rate constant data for these same reactions and are shown to provide essential confirmation for the Wagner theory. For the most part, the results are also consistent with the previously proposed transport mechanisms in the oxides of iron. WHEN a metal is exposed to an oxidizing atmosphere at elevated temperatures, a superficial oxide layer is formed which then thickens according to some characteristic rate law. Provided that the oxide layer is dense and continuous and does not present any paths for gaseous diffusion, continued growth must inevitably involve the migration of the reactants—either the metal or oxygen or both—through the lattice of the solid oxide. This is true whether the reaction rate is controlled by the diffusion process itself or by a slow step in a reaction at one of the interfaces. If the overall rate is limited by diffusion, and if the concentrations or thermodynamic activities of the reactants at the boundaries of the oxide layer are independent of time, the familiar parabolic rate law is observed. Under these conditions, Wagner1 has shown that the rate constant may be expressed in terms of the mobilities of the reacting components and the appropriate concentration or activity gradients which are established across the growing oxide layer. In presenting the phenomenological basis for the theory, Wagner has emphasized the role played by lattice defects in diffusion processes in oxides. The essential validity of this theory has been confirmed by experiment for a number of simple systems including the growth of Cu2O on copper.'-' One of the objectives of the present study has been to extend the Wagner approach to the more complex process of the oxidation of iron and its oxides, and particularly to wustite, which is normally the major constituent of the oxide scales formed on iron at temperatures above approximately 570°C. For this purpose the rates of self-diffusion of iron in w?stite, magnetite, and hematite have been measured by tracer techniques and the necessary thermodynamic data have been obtained from equilibrium studies involving the oxides and their atmospheres. These data have subsequently been used to test the underlying assumptions of the Wagner theory as well as the detailed mechanism of the scaling of iron previously proposed by Davies, Simnad, and Birchenall.5 Lengthy treatments of diffusion and conduction phenomena in ionic crystals have been published." * The latest, by Jost,8 also summarizes much of the existing experimental data. In general, however, the oxides of iron have not been considered specifically and hence a brief review of the available

Jan 1, 1954

By G. W. H. Norman

"The Indian Molybdenum deposit occurs in granite near the centre of Indian peninsula, Kewagama lake, in Preissac township, Abitibi county, Quebec, about 40 miles east of Noranda. Quartz veins containing molybdenite were discovered in the vicinity of the deposit in 1901 by J. F. E. Johnston of the Geological Survey of Canada. Innumerable trenches and a few pits were excavated during and prior to the first great war, but there was no production. During the second great war systematic drilling along a favourable zone disclosed by the earlier trenching outlined an orebody of 225,000 tons with a molybdenite content of 0.46 per cent.A 500 on mill was built in 1943, and 91,489 tons of ore underwent treatment, from which 699,568 lb . of molybdenite was recovered. The mill closed down early in 1944 when the wartime need for Canadian molybdenum production eased .GEOLOGYThe general geology in the vicinity of the deposit is shown in Fig. 1. The deposit lies at the north edge of a muscovite-biotite granite mass about 2 miles wide and several miles long. West of Kewagama lake this granite is cut by great swarms of quartz veins . The only other granite in the district known to contain similar swarms of quartz veins, and which similarly has become a source of mo!ybdenite, occurs 20 miles east in La Corne township. The non-molybdenite-bearing granites of the district are either more basic and contain frw dykes except aplite or are distinctly pegmatitic types and contain up to 50 per cent pegmatite dykes with molybdenite only here and there in small amount."

Jan 1, 1954

By J. W. Watkins

This report describes in detail methods of making corrosion tests and chemical analyses that have been used extensively and satisfactorily in a study of plants in which various surface, waters and brines are conditioned and used for water flooding, brine disposal, and reservoir-pressure maintenance in Kansas, Oklahoma, and North Texas. The tests and analyses described were designed and adapted for use in the field in determining the relative corrosive and plugging tendencies of waters from various sources conditioned by different methods. Although the described methods were developed and used in testing oil-field waters in the Midcontinent oil-producing area of the United States, these same methods should be equally applicable to testing oil-field or highly mineralized waters throughout the world. Many of the methods used have been discussed by the writer (1)2/ previously, and some of them have been used for similar work in other laboratories. Early in the development of the practice of the subsurface injection of brines for disposal and increasing the recovery of oil, it became evident that different methods of chemical treatment and conditioning equipment would have to be devised to sustain desired injection rates into water-input wells. These changes became necessary because the highly mineralized waters produced with petroleum from deep formations became chemically unstable when pumped to the surface, owing to loss of dissolved gases as pressure and temperature dropped to atmospheric and to the contact with atmospheric oxygen at the surface.

Jan 1, 1954

By John B. Gayle

A new, experimental coke oven was installed at the Southern Experiment Station, Tuscaloosa, Ala., in 1948. This oven, designated as the Tuscaloosa oven, features a 17-inch carbonizing chamber, globar heating elements, and silica-brick heating walls designed to simulate as closely as possible carbonizing conditions in commercial, slat-type coke ovens. Zoned heat-input arrangements maintain uniform temperatures over approximately 95 percent of the total flue area. The reasons for constructing an oven of this size, the details of the design, and the operating characteristics of the oven were given in an earlier publication.2/ This report presents the results obtained from the first series of carbonizing tests on Alabama coals with the new oven. Factors leading to the development of standardized operating and testing procedures and the results of crosscheck determinations with a commercial oven producing foundry coke are included also.

Jan 1, 1954

By J. J. Gilman

The data presented indicate that the critical shear stress and strain-hardening Thedatapresentedrate of a zinc monocrystal depend on the orientation of its slip direction with respect to its external boundaries. The tendency of a crystal to form deformation bands also depends on its shape. THE plastic behavior of pairs of zinc monocrystals in which both members of the respective pairs had the same orientation with respect to the longitudinal axis, but each had different orientations with respect to their rectangular external shapes, were compared in this investigation. The purpose of the investigation was to see what influence the shape or surface of a zinc crystal has on its mechanical properties. In a previous investigation of triangular zinc monocrystals,1 anomalous axial twisting was observed which seemed to be related to the triangular shape of the crystals. Wolff,' in 400°C tensile tests of rectangular rock-salt crystals bounded by cubic cleavage planes, found that, of the four equivalent slip systems, the two with the "shorter" slip directions yielded and produced slip lines at lower stresses than the other two. This observation and the work of Dommerich³ as formulated by Smekal4 as a "new slip condition" for rock-salt: "among two or more slip systems permitted by the shear stress law, with reference to the formation of visible slip lines by large individual glides, that slip system is preferred which has the shortest effective slip direction." More recently, Wu and Smoluchowski5 reported essentially the same effect for ribbon-like (20x2x0.2 mm) aluminum crystals at room temperature. Experimental Chemically pure zinc (99.999 pct Zn), purchased from the New Jersey Zinc Co., was the raw material. Glass envelopes, containing graphite molds and zinc, were evacuated while hot enough to outgas the graphite but not melt the zinc. At a vacuum of about 0.2 micron the envelopes were sealed off and then lowered through a furnace at 1 in. per hr so as to melt and resolidify the zinc and produce mono-crystals. One-half of one of the molds is shown in Fig. la. Each mold consisted of four pieces from a cylindrical graphite rod that was split longitudinally and transversely at its midpoints. Rectangular milled grooves 0.050 in. deep and % in. wide formed the mold cavity when the split halves were assembled with twisted wires. Fig. lb shows the specimen shape obtained when the top and bottom mold-halves were rotated 90" with respect to each other. Good fits prevented leakage and excess zinc was necessary to provide enough liquid head to fill the mold completely. In removing soft crystals from the molds it was impossible to avoid small amounts of bending. However, manipulations were carried out whenever possible with the crystals protected by grooved brass blocks. All specimens were annealed prior to testing. From the top and bottom sections of each crystal, X-ray specimens and tensile specimens 7 to 8 cm long were sawed. The tensile specimens were annealed inside evacuated tubes for 1 hr at 375°C. Next the crystals were cleaned and polished by 2-min dips in a solution of 22 pct chromic acid, 74 pct water, 2.5 pct sulphuric acid, and 1.5 pct glacial acetic acid.' Cleaning was followed by a 10-sec dip in a 10 pct caustic solution, then washed in water and alcohol, and dried. This treatment results in a bright surface covered by an invisible oxide film. The testing grips were a slotted type with set screws and were supported in a V-block during the mounting operations in order to avoid bending the crystals. A schematic diagram of the recording tensile-testing machine is shown in Fig. 2. The machine has been described elsewhere.' The head speed was 0.3 mm per sec for all tests. The crystal orientations were determined by the Greninger X-ray back-reflection method with an estimated accuracy of 1. Description of Crystal Geometry A schematic picture of a rectangular zinc mono-crystal is shown in Fig. 3. ABD designates the front edge of a basal plane (0001) of the crystal, the only active slip plane for zinc at room temperature. Of the three possible (2110) slip directions, the active one is indicated by an arrow. Cartesian coordinates are taken parallel to the specimen edges. The normal, n, to the basal plane (n is parallel to the hexagonal axis) has the direction cosines a, ß and ?. X0 = 90 — y is the angle between the longitudinal axis and

Jan 1, 1954

1. The following recommendations should apply to all mines, tunnels and underground quarries, but to opencast quarries only in so far as persons can be exposed to dust injurious to health. General In the present state of knowledge, all duets liberated in mining, tunneling and quarrying operations should be considered potentially injurious to health if breathed in sufficient quantity; dusts containing free silica should be considered specially injurious to health, the injurious particles being below 7 microns in diameter.

Jan 1, 1954

By J. E. Gill

"The name 'Canadian Shield' is used for a vast area; largely in northeastern; Canada; underlain by Precambrian rocks. The part in Canada has an area; of about 1; 790; 000 square miles. Extensions in Greenland; Labrador; Newfoundland; and the United States bring the total area to around 2; 800; 000; square miles. The boundaries of the Canadian part are shown in Fig. 1.; At its margins; the Precambrian rocks can be seen at many places to; extend beneath a cover of flat-lying Palxozoic or later sediments. Information; from borings in the Plains and natural exposures in mountain-built belts; show that similar rocks form a large part of the continental platform. The; Shield; therefore; is a large exposure of what may be regarded as the foundation; of the continent."

Jan 1, 1954

By N. J. Grant, I. S. Servi, A. Chaudhuri

IN a recent paper by Servi and Grant,' it was illustrated that the slip band spacing and stress based on creep test data were related by the equation: d =1/ where d is the spacing in millimeters and v is the stress in psi, based on a more complete equation proposed by Orowan. It was shown further,' that for a. given grain size, the slip band spacing became larger with decreasing stress (and was independent of temperature), until such time that the slip band spacing becomes greater than about one-half the grain diam- eter. When this occurred, the mechanism of deformation in creep of 2s aluminum at high temperature changed from slip to grain boundary deformation (sliding). Additional metallographic evidence is now available which confirms this in a most interesting fashion.

Jan 1, 1954

By E. A. Jones

THE Southeast Missouri division of the St. Joseph Lead Co. normally hauls and hoists over 5 million tons of lead ore each year. This ore is mined in the stopes and headings of 20 mines, hauled to a main line system, see above, and transported up to 6.4 miles to ore-hoisting shafts. Average haulage distance is 2.16 miles. A few years ago a distinguished mining engineer visiting this area for the first time remarked, "You do not have a mining problem; yours is a haulage problem." Its relative importance may be gaged by the fact that mine haulage represents about 25 pct of the total cost of mining ore, the most costly single underground operation. The Southeast Missouri lead belt is a mining district located about 65 miles south of St. Louis. This district is roughly 6 miles wide and 10 miles long. The ore horizon lies about 400 ft below the surface where most of the ore is mined from flat-lying beds of dolomitic limestone. This paper deals with the central part of the district, namely, that portion which contains a group of interconnected mines all in a central haulage system, serving four hoisting shafts. The two major hoisting operations are carried out at Federal No. 17 shaft and Leadwood No. 12 shaft. No. 17 accounted for about 70 pct of the ore hoisted in the district during 1950, averaging about 14,000 tons per operating day. The underground dumping and skip-pocket system at this shaft is similar to those of the other shafts except that it has two rotary dumps. The other ore-hoisting shafts have only one. It might be mentioned that waste rock is hoisted at still other shafts, hauled off, and dumped on the surface by trucks. The hoisting shafts are on a connected system of about 200 miles of underground 24-in. gage main line railroad. There is also the Bonne Terre system, with its own ore-hoisting shaft, which consists of 13.5 miles of 24-in. gage main line, located in the extreme north portion of the lead belt area. Smaller outlying mines such as Doe Run No. 12 and Hayden Creek operate on trackless or shuttle car haulage. In addition to the system of main line haulage, each contributing mine group has its own extensive system of stope or heading railroad. Trackless mining is making considerable headway in the Lead-wood and Desloge mines. Here the shovel loads into a shuttle car which in turn dumps into mine cars spotted on the main line track system. When the merits of underground haulage and surface transportation are compared, it must be remembered that in early days there were many individual

Jan 1, 1954

By J. H. Douglas, A. F. Matheson

"The Hard Rock is the most easterly producing mine in the Little Long Lac area. The Company was formed in 1934 to develop a surface showing of gold in quartz made by a prospector, W. W. Smith, in 1931. Although some ore was eventually produced from this discovery, the principal orebody, hidden below 10 feet of muskeg, was found about 1,000 feet to the north by exploratory diamond drilling early in 1938 from the No. 2 shaft workings at the 250-foot level.Production started in 1938 and to January 1, 1947, 201,000 oz. gold had been obtained from 1,165,282 tons of ore mined and 869,397 tons milled. Of this ore about 15 per cent came from the development and mining of the original orebodies discovered at the surface. The remainder came from the ore found by the underground diamond drilling done in 1938. Of the latter ore, the Company estimated, at January 1st, 1947, only 140,000 tons remained. The orebody, therefore, contained approximately 1,100,000 tons.OREBODIES AND GENERAL GEOLOGYThe orebodies of the Hard Rock mine are of two main types: the quartz ore of the south and No. 1 shaft zones, and the sulphide ore of the north zone. The quartz ore consists of white quartz veins mineralized with sparse, fine, light-coloured pyrite, or, less commonly, nests of coarse, crystalline, light pyrite. A little tourmaline, scheelite, pyrrhotite, chalcopyrite, arsenopyrite, and native gold are also present. Native gold occurs in a few places in quartz veins in exceedingly rich cemcentrations, apparently where there are large, light-coloured, pyrite crystals of imperfect form. The ore of the north zone is massive pyrite with arsenopyrite and in places pyrrhotite. Many short irregular quartz veins, from a few inches to 2 feet in width, are also present, but the quartz forms a very small percentage of the whole. The veins may be flat to vertical, and sulphides on one or both sides replace the host rocks. The gold is closely associated with the sulphides . The quartz is commonly barren except where it contains sulphides or along the borders of the sulphide ore zone where native gold is not uncommon in quartz stringers."

Jan 1, 1954

By T. H. Adair

"IntroductionCONTINUOUS casting of ferrous and non-ferrous metals is not a new innovation. Patents describing machines for continuous casting are on file as far back as the year 1842. In the middle of the last century, Sir Henry Bessemer conceived and built a continuous casting• machine for the production of mild steel sheet.The production of billets and slabs of both non-ferrous and ferrous metals is being carried out by the continuous method on a fairly large scale on this continent and abroad. At present, the volume of production of •copper and aluminum and their alloys in billet and slab form is much greater than the continuous casting of steel products. The new installation of a continuous casting unit at Atlas Steels, Limited, is designed primarily for the casting of alloy steel billets and slabs.As an introduction to the art of continuous .casting of metals, it is interesting to examine a few of the many devices which have been developed. As previously mentioned, Sir Henry Bessemer constructed a machine for the direct casting of mild steel sheet. His discoveries and ideas of continuously casting steel formed the foundation for the work of other pioneers in this field, all of whom have contributed to the improvement of this art through the ensuing years. The machines which will be selected for examination are those of Bessemer, Poland-Lindner, Williams, Ennor, and Junghans. The last unit to be discussed will be a modification of the Junghans machine recently installed at Atlas Steels."

Jan 1, 1954

By R. C. Troxell, S. C. Sun

EFFORTS to obtain definite quantitative data when employing the currently used bubble pick-up method1,2 as a pre-flotation investigation tool led to the adoption of the magnifying mirror method and the microscopic method modifications. Quantitative data obtained by these two methods were converted into bubble pick-up indices and bubble pick-up coefficients. Rough correlations were established between the calculated indices and the results of contact angle testing as well as actual flotation under the same conditions. The basic steps of the magnifying mirror method are as follows: 1—mixing 200 ml distilled water, sized and cleaned mineral particles of approximately 0.5 g, pH regulator, and flotation reagents in a glass beaker; 2—swirling the mineral particles to the center of the beaker to leave a clear circumference; 3—pressing an air bubble against the mineral particles for about 1 sec, and then moving the mineralized air bubble to the clear part of the beaker; and 4—dropping all the attached mineral particles of the air bubble by tapping the bubble holder, and counting the number of the dropped particles by looking at the magnified image in the mirror positioned beneath the beaker. This method is impractical for mineral particles which are transparent in water or finer than 200 mesh. The microscopic method is essentially similar to the above described magnifying mirror method, with the exception that the mineralized air bubble was drawn up into the bubble holder and subsequently discharged onto an externally placed watch glass, where the number of pick-up particles was counted with the aid of a microscope or hand lens. Drying was necessary when the discharged liquid interfered with the counting. The results of the bubble pick-up tests can be simply expressed in the form of the actual count. However, this can be misleading because the number of pick-up particles varies not only with the size of bubble but also with the size of particles. This short-coming is largely remedied by the use of the bubble pick-up index. as calculated from the following equation: PI = (pn/p) 100 [1] in which PI and pn are respectively the pick-up index and the number of pick-up particles under any test conditions, and p is the maximum number of pick-up particles of the same mineral under optimum flotation conditions, with the same size holder and particle. The bubble pick-up coefficient is a term coined to denote the difference between the bubble pick-up index of mineral particles in a liquid and that of the same mineral-liquid mixture plus a chemical reagent at the same pH value. For example, the difference between the pick-up index of a naturally floatable bituminous coal in a solution of water and kerosene and that of the same coal in water alone is a bubble pick-up coefficient. Compared with the contact angle method, the quantitative bubble pick-up method is inferior in accuracy but superior in sensitivity. Other advantages of the bubble pick-up method are that the apparatus can be easily assembled, the mineral sample is conventionally prepared, and the test procedure is relatively simple. References S. R. B. Cooke: The Flotation of Quartz Using Calcium Ion As Activator, Trans. AIME (1949) 184, p. 306. 'G. A. Last and M. A. Cook: Theory of Collector-Depressant Equilibrium at Mineral Surfaces. Paper presented at St. Louis Meeting, AIME (February, 1951).

Jan 1, 1954

By Robert H. Merrill

This report contains a summary of the various studies made to determine the structural design of the production mine area of the Oil-Shale mine, Rifle, Colo. Prior to this investigation, it had been determined from a study of the geology, the structure of the deposit, and mining costs that the deposit should be mined by open stoping. The problem remained to determine the maximum safe roof span, the optimum extraction ratio, and the size of the pillars. These factors were determined from a study of the geologic structure of the deposit, the physical properties of the oil shale, and the magnitude and distribution of the stress around proposed underground openings. The latter was determined from both theoretical calculations and model studies. Safe roof spans, pillar sizes, pillar contours, and optimum extraction ratios were calculated from elastic theory and the physical properties of the mine rock. Safe roof spans, pillar sizes; and time effects were determined by Wright and Bucky by testing mine models in a centrifuge. The models were made from rock specimens taken from the proposed mine roof and pillars. The results from both studies agreed.

Jan 1, 1954

By F. Y. Grepe

"THE MOST common type of mine hoist is, as is very well known, that in which the a.c. wound rotor motor is the driving medium. The reasons for the use of the wound rotor motor are, of course, economic. This type of equipment has, during the years, proved to be very reliable and reasonably satisfactory. It is, in fact, still being installed and in some places where a very hard and exacting duty cycle is demanded. As an example, a 600 h.p. 2,300-volt job was recently installed at the Caledonia mine (1) at Glace Bay. This is a vertical. hoist in a shaft only 175 feet deep but it is, nevertheless, working hard bringing coal to the surface and in making a trip at a speed somewhat better than every 20 seconds.The control equipment for such installations usually consists of a pair of primary reversing contactors which are interlocked both mechanically and electrically, together with some form of secondary controller. This, in the case of small hoists, can be a drum controller and metallic resistors or, in the case of larger hoists, a magnetic contactor panel and metallic resistors or, alternatively, can be one of the various forms of liquid rheostats which are available. The liquid rheostats, if of the dipper type, may be manually operated or it may be operated by some form of servo motor mechanism. In the weir type of liquid controller, the electrolite is, of course, pumped in and out of the rheostat."

Jan 1, 1954

By H. C. Cooke

"This paper has reference in a general way to the region extending from the north shore of lake Buron to the northern limit of the elliptical-shaped area generally known as the Sudbury Basin, and more especially to the district lying south of the Basin (Fig. 3). Attention is concentrated mainly on the structure of the district and, as space does not permit of much geological description, it is assumed that the reader has some knowledge of the general geology. The accompanying table outlines the sequence of the rock formations according to the most recent available information; for further details the interested reader may consult the publications of the various authors mentioned in the paper.STRUCTURE OF THE SEDIMENTARY ROCKS SOUTH OF THE SUDBURY IRRUPTIVEThe rocks south of the Sudbury irruptive, excluding certain intrusives, are, in order from north to south:(1) A band of basic lavas.(2) A band of well-bedded greywackes and quartzites, long termed the McKim greywacke.(3) The Copper Cliff formation, with McKim greywacke' both to the north and south.(4) The Ramsay Lake conglomerate.(5) A thick quartzite formation.All these rocks strike approximately east-northeast, dip steeply south, and generally face south, though there are local exceptions."

Jan 1, 1954

By N. E. Hanna

[Testing explosives for safe use in coal miner ran boon an important factor in preventing mine explosions. In the United States, explosives that have been approved by the Bureau of Mines are called permissible explosives. A purvey of the history of coal mining since permissibility testing welt, instituted some 4 years ago shown that there is no record of a coal-mime explosion caused by permissible explosives when used in a manner prescribed by the Bureau. To maintain the appropriate standards of quality, the Bureau of Mines conducts a series of examinations and tenth on samples of explosives collected in the field. In what is considered the most crucial test, teat 1, the explosives An fired from a steel cannon into a gallery atmosphere containing a mixture of natural gas and air, In another important test, test 4, the explosives charge to fired into a mixture of natural gas, air, and coal diet. To satisfy the permissibility requirements, the explosive must undergo throe gallery teats without igniting gas or coal duet. Other tests also are required for permissibility, but they do not come within the scope of the present paper, which studies the factors affecting the incendivity of explosives when fired into methane, air, and/or coal-dust mixtures. It in believed that a better understanding of the factors will contribute to the development of safer explosives.]

Jan 1, 1954

By B. S. W. Buffam

"The property of Moneta Porcupine Mines, Limited, consists of a group of eight claims in Tisdale township, Ontario. It includes part of the townsite of the town of Timmins, and adjoins the west boundaries of the Hollin_ger Consolidated and Mace properties. The Moneta property was first staked in 1909, about a year after the first discovery of gold in the Porcupine camp. In 1910 the Moneta Company was incorporated and some preliminary exploratory work performed by Nova Scotia Mines of Cobalt. In 1912 English interests advanced $90,000 for diamond drilling and underground work. One drill hole gave high assays, but apparently the records were poorly kept or the cores were interchanged. As a consequence, when underground exploration was undertaken in 1923 it was directed south rather than west and no ore was found . In 1924 about 5,000 feet of diamond drilling was done in the southern part of the property, but without intersecting ore.In 1931 W. E. Segsworth assumed the direction of the property. Diamond drilling commenced on August 18, 1936. The first hole intersected 9.9 feet of ore averaging 1.23 oz. gold a ton. Underground work was started early in 1937. A mill was erected in the autumn and the first gold brick was poured January 29, 1938.The Moneta mill began operation on January 2, 1938, and the following table gives a summary of the production to June 30, 1943, when the mill was closed."

Jan 1, 1954

By D. J. Carney, E. C. Rudolphy

IT has been demonstrated that inclusion size, distribution, and composition affect the machin-ability of resulphurized steels. Merchant and Zlatinl concluded that large sulphide inclusions aided machining by forming a (lubricating) coating on the tool face. Boulger et al.² and Van Vlack³ noted that the size, distribution, and composition of the inclusions in the steel affected the machinability. Steel specimens containing large globular sulphide inclusions usually exhibited excellent cutting properties, while machinability was adversely affected by the presence of numbers of oxide-type inclusions. Consequently a thorough knowledge of all the factors which affect the inclusions in the final product is desirable. Since almost all the inclusions have their origin in liquid steel, it was necessary to begin a study of inclusions in free-machining steels by studying the inclusions and chemical segregation in the as-cast ingot. Very little information is available on the size, distribution, shape, and composition of inclusions in large, capped, free-machining steel ingots, particularly the B1113 grade. Gregory and Whiteley4 made a general study of the inclusions in a small, high sulphur, free-machining steel ingot. Also, numerous authors have described the solidification and segregation characteristics of the four basic types of steel ingots, namely, rimmed, capped,7 semikilled,7,8 and killed7,9,10 ingots. Most of these studies were made with plain carbon or low alloy, low sulphur steel. It was desirable to study not only the ingot but also the change in size, shape, and number of inclusions on rolling an ingot to a bloom and thence to a billet. This procedure was followed and it is hoped that this study may serve the dual purpose of adding to the general knowledge of ingot solidification as well as contributing to the knowledge of the size, shape, distribution, and composition of inclusions from the ingot to the billet in a high sulphur, free-machining steel. Procedure A 12.000-lb 23x35x75 in. slab ingot of the B1113 grade was cast, sectioned, and studied both macro-scopically and microscopically. An adjacent ingot from the same heat and of the same size was rolled to a 77/8x77/8 in. bloom and thence to a 21/2x21/2 in. billet. These various bloom and billet sections were also sectioned and studied macroscopically and microscopically. Sectioning the Ingot: The ingot herein described was obtained from the United States Steel Corp.'s South Works Bessemer Blow No. 0193, a B1113 mechanically capped heat. The 23x35 in. ingot (No. 2) was teemed according to normal procedures and after stripping and transportation to the rolling mill was not placed in the soaking pit but allowed to air cool in an upright position. When completely solidified, the ingot was cut into sections by means of a powder scarfing torch and further sectioned by saw cutting as indicated in Fig. 1. Cut No. 2 (1x10x12 in.) from sections A through H was cleaned thoroughly, macroetched in a solution of 50-50 water and hot muriatic acid and used to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 23-in. ingot dimension. Cuts No. 5 and 3 (lx81/2xl0 in. each) from sections A through H were treated in a similar manner to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 35-in. ingot dimension. The composite macrograph of these horizontal ingot sections, which shows a vertical section of the ingot from top to bottom, is shown in Fig. 2. It should be noted that sections No. 2 are normal to sections 5 and 3 in the composite. Drillings for chemical analyses were obtained from selected positions within the above-mentioned ingot sections as noted in Fig. 3. The oxygen content was determined by the vacuum-fusion method. Samples for microscopic examination were cut from

Jan 1, 1954

By W. Graham

"IntroductionEFFLORESCENCE is herein considered to be any deposit of salts on the surface of a masonry structure that is brought from within or through the structure by capillarity and deposited by evaporation. Usually, efflorescence is white although green, yellow, and brown efflorescence is sometimes observed.The common white efflorescence almost always consists of sulphates of the alkali and alkaline earth metals and calcium carbonate, although sodium chloride is frequently present in structures erected near the sea shore.The first and most obvious result of the presence of soluble salts in masonry is the unsightly accumulation of these salts on the surface. This is particularly noticeable early in its life and is frequently fugitive ( 1), as much of the salt is soluble and is gradually washed away by rain. This removal can usually be facilitated by scrubbing; the structure with dilute hydrochloric acid.A more serious effect is the continuous accumulation of soluble salts as a result of ingress of sulphur acids in rain water or water from the ground. This may eventually cause spalling and disintegration by crystallization of salts in the pores of brick and mortar. An example of this type of failure, resulting from the crystallization of calcium sulphate, is discussed by Hardesty (2). Butterworth (3) describes similar failure resulting from •crystallization of magnesium sulphate."

Jan 1, 1954