Search Documents

By E. P. Carman

1. DAVENPORT, S. J. Bibliography of Bureau of Mines Publications Dealing With Health and Safety in the Mineral and Allied Industries, 1910--46. Tech. Paper 705, 1948, 154 pp. 30 cents. 2. FJELDNER, A. C., FISHER, P. L., AND POLLOCK, M. B. Bibliography of Bureau of Mines Investigations of Coal and Its Products, 1940 to 1945. Tech. Paper 698, 1947, 53 pp. 15 cents. 3. GOOD, J. E., ABREU, ALVARO, AND FRASER, THOMAS. The Coal Industry of Brazil. Part 1. General Economy, Production, and Marketing. Tech. Paper 713, 1949, 38 pp. 20 cents.

Jan 1, 1954

By J. F. Neill, O&apos

[The Cartersville mining district is in Bartow County, Ga., about 40 miles northwest of Atlanta. Barite, limonite, ocher, amber, hematite, and, manganese oxide ores have been produced from the strict since about 1840. In the search for a possible source of manganese ore, Bureau of Mines engineers made a preliminary study of the district from September 1950 to January 1951. During this study 139 deposits were examined, and many mineral exposures were sampled. Manganese mineralization occurs as fine oxide and concretionary pellets in residual clays, as fine oxides in umberous clay, in brown-iron deposits, and in a limited quantity in mud ponds and Jig-tailing piles. The future supply of ferrograde manganese ore from the district, using current mining and benefication methods, appears limited to the recovery of the hard manganese ores deposits. Rough estimates indicate a reserve of manganese-bearing clays of about 8,000,000 long tons. This type of deposit has been extensively exploited and the larger deposits mined out to depths of from 50 to 200 feet. The remainder of these deposits are low grade, are covered with deep layers of colluvium, or lie below the ground-water table. Any future production from this source will require systematic prospecting, improved concentration, and an increase in the price of concentrate.]

Jan 1, 1954

By J. W. Miller

This report deals with upgrading of the coal reserves of Raleigh County, VI. Va., to metallurgical standards. The data on samples herein correctly show the characteristics of the bed at the point where sampled and are used to indicate the general quality of the bed in the county. The principal results and conclusions are: 1. Raleigh County contains large reserves of high-quality, high-, medium-, and low-volatile coals. 2. The principal beds from which an increased amount of coal is expected to be mined in the future are: The Eagle, Powellton, No. 5 Block, Hernshaw, Fire Creek, and Pocahontas No.6.

Jan 1, 1954

By R. A. Halet

"The Malartic Gold Fields mine is a good example of the association of ore deposits with a major fault zone. It also exemplifies the control exerted by the physical and chemical character of the host rocks on the localization of orebodies.The mine is in Fourniere and Dubuisson townships, Abitibi county. It is 6 miles east of the town of Malartic, 9n the main highway and railway from Noranda to Val d'Or.The discovery of the mine is due largely to the enterprise of the late J. P. Norrie, who organized the present Company in 1935. The ground is entirely covered by overburden, but Mr. Norrie believed that the extension of the Cadillac-Malartic 'break', the principal ore-bearing structure of the district, would be found on this group of claims. This belief was supported by the discovery of gold-bearing float in the area, and was confirmed by a dip-needle survey and a few pilot diamond drill holes that showed that the favourable Malartic greenstone band passes through the centre of the property.In this way the most favourable area for prospecting was narrowed to a zone 2 ½ miles long by ½ mile wide underlain' by greenstone. The remainder of the property is underlain by sedimentary rocks, which, from experience elsewhere in the camp, were not considered as promising. However, as the entire surface is covered by deep overburden, the location of orebodies even within this more or less restricted area could be accomplished only by a long campaign of diamond drilling. Systematic diamond drilling began in 1936.The contacts of the greenstone band were considered to be the most promising places to begin the work, and the early drilling was concentrated on the south contact, because the orebody of the East Malartic mine, 4 miles to the west, had been discovered on this structure and it was reasonable to hope for a repetition of these conditions. Although the south contact was very thoroughly explored, with a certain amount of encouragement, the work did not prove the existence of deposits of ore grade, and attention was shifted to the north contact zone of the greenstone band. In this locality much more promising results were obtained, and a number of good orebodies were outlined."

Jan 1, 1954

The lignite deposits of the United States represent a huge potential source of fuel for power generation. It has been estimated that lignite constitutes about 24 percent of the remaining National reserves of solid fuel on a tonnage basis and about 15 percent of the reserves on a B.t.u. basis. (See sec. 3, part 1.) The major portion of these reserves is in North Dakota. Lignite has been used locally for domestic heating since the first settlers burned it at forts and fur-trading posts as early as 1855. Some of the first studies of the use of lignite in steam boilers were conducted by the Federal Bureau of Mines from 1910 to 1920 (15, 19) 1/ However, the commercial utilization of lignite as fuel for producing power developed slowly. Not until about 1925 was any really successful lignite industrial fuel-blaming equipment developed. Since then the commercial use of lignite as a fuel for producing power has been increasing steadily.

Jan 1, 1954

By Leroy E. Schulze

A review of development and a reevaluation of uses of the hydraulic air compressor are suggested by the constant changes in technology, which frequently make an old art valuable in solving current problems. Contacts with research workers in various branches of engineering indicate that this older method of producing compressed air may not be familiar to some or that its salient features might be useful in solving problems involving uses of compressed air. Briefly, a hydraulic air compressor may be described as an inverted siphon, consisting of an intake head where water and air are mingled, followed by a gravity-fall tube in which air is intimately mixed with the water and is compressed as the water pressure increases during the fall down the tube, then a separating, or stilling, chamber in which air bubbles rise to the surface of the water and collect in the upper portion of the chamber at a pressure equal to the weterhead maintained by the height of water in the discharge leg of the circuit. The water, which now contains only the fraction of air that has gone into solution, passes out of the separating chamber and rises up the discharge leg to the surface, which is, of course, at some suitable distance below the level of the intake. Present-day applications include (1) utilizing low hydraulic heads, which otherwise have little commercial values; (2) utilizing low hydraulic heads in reclamation work to supply compressed air, or in some instances to produce a small suction, for air-lift pumping (or for operation of air motors), with minimum attendance and without need for electric power; (3) utilizing medium heads, as at dam and lock installations, to produce compressed air for pneumatic operation of airlifts, gates, valves, and rubber gate seals; (4) utilizing underground waters, as in mines, to produce compressed air for general mine use; (5) using this method of isothermal compression of air in combination with standard compressors wherever hydraulic head is available, thereby securing the advantages of low-temperature intake to the mechanical compressors and reduction of moisture content below that of atmospheric air; (6) development of large air supply at pressures up to 150 p.s.i.g., which, after performing work in reciprocating or centrifugal expansion cylinders, is available at temperatures approximating -50° F. Possibilities in freezing and reheating should be mentioned which may prove economical for obtaining uniformly dry air for process work, wind-tunnel tests, or large air-conditioning installations, such as ventilation of underwater traffic tunnels, and may be economic for supply of supercharged air to gas-turbine plants.

Jan 1, 1954

By Edward P. Barrett

SPONGE IRON has been defined as the metallic product formed by the reduction (removal of combined oxygen) of iron ore or other iron oxides at temperatures below the fusion point of iron. This product probably derived the name "sponge iron" from its porous nature. When the reduction proceeds at slightly higher temperatures and the particles of metal weld together or finally even melt to yield pellets or balls that lack the porosity and low-density characteristic of sponge iron, the product might more correctly be called "direct iron."

Jan 1, 1954

By Alfred L. Ransome

The plan to develop a standard system of names and definitions of regions and districts in Alaska was borne of the need for a tool to use in statistical and economic studies of the mineral industry of the Territory. The purpose of this report is to present to the mineral industry, and to those individuals interested in the mineral or allied industries in Alaska, the system used by the Bureau of Mines in connection with its legal function of collecting and disseminating mineral statistics. It is hoped that the specific descriptions given will result in a more complete understanding of what is meant by the regional and district names that appear in publications of the Bureau of Mines relative to the mineral industry of the Territory. Problem of Standardization of Names and Definitions The question might be asked, does the naming and defining of regions and districts in Alaska present a problem relative to the establishment of a standard? Is it necessary to establish a standard?

Jan 1, 1954

R. W. Balluffi (Atomic Energy Div., Sylvania Electric Products Inc., Bayside, N. Y.)—Since porosity is known to form in the copper side of Cu-Ni couples during diffusion24,25 it is of importance to consider this factor in interpreting the large variations of chemical diffusivity with copper concentration reported for this system. The presence of porosity may affect the measurement of D in two ways: 1—density changes in the couple invalidate the usual solutions of the diffusion equation, and 2—the pores may act as short-circuiting paths when transport through the vapor or along internal surfaces is appreciable or else as open circuits when these effects are small. The error produced by the first effect may be estimated by a graphical analysis. Fig. 8 shows the porosity generated in the copper side of the Kirkendall interface of a pure nickel vs pure copper couple after diffusion for 350 hr at 1040°C in hydrogen. In Fig. 9 the actual diffusion curve which would be obtained by the usual slicing technique is shown as a solid line drawn to the same scale (from the data of da Silva and Mehl"). The amounts of porosity (obtained by lineal analysis) and of nickel are graphically represented by the hatched areas. The standard solutions of the diffusion equation are valid only when all volume elements of unit length and unit cross section contain equal numbers of atoms." It is possible to correct the experimental curve to satisfy this condition by shrinking the couple in the direction of diffusion in such a way as to eliminate the porosity.* The corrected diffusion curve obtained after

Jan 1, 1954

By D. S. Kingery

This study describes five fatal accidents so unusual in occurrence that the chain of circumstances bringing them about may never be duplicated. The intent of this publication is to illustrate that everyone working underground is subjected, at all times, to definite inherent mining hazards and that safety devices, though provided, often are ineffective or not used. It is hoped that a study of these fatal accidents in bituminous-coal mines will show workers and safety engineers that nothing can be taken for granted. Safety planning with continuous study can prevent these unusual accidents as well as the routine recurring types, which cause the majority of coal-mining injuries. The treacherous, fatalistic philosophy that "it can't happen to me" or that "when my time's up I'll get it regardless of what I do," still prevails among individuals and even safety engineers. The individual or safety man who believes in luck as applied to safety should not read any further, since this study was written for the sincere, safety-minded individual who accepts the prevention of all accidents as a challenge to his knowledge, initiative, persuasiveness, and salesmanship.

Jan 1, 1954

By Robert A. Brown

"The O'Brien mine is in the west-central part of Cadillac township along the Cadillac 'break', which extends for 7,500 feet from west to east across the property.The ground was staked in 1924 by A. Dumont and W. Hermeston, prospecting for M. J. O'Brien, Limited. The first vein discovered is that now known as No. 1. The No. 4 vein was later exposed on the surface; the other veins known to be present were revealed by underground work and diamond drilling carried out both from the surface and underground.The mine is developed from three vertical shafts: No .. 2 extending from the surface to 2,000 feet; No. 3 from the surface to 1,500 feet; and No. 4 from 2,000 to 3,000 feet. There is on the property a mill of about 200 tons a day capacity, the usual shops, and a townsite housing about forty-five families. Gold production to the end of September, 1944, amounted to 295,824 fine oz. from ore having an average grade of 0.505 oz. a ton. In addition, the mill recovered 3,237 tons of arsenic trioxide having a purity of 83 per cent As2O3.GENERAL GEOLOGYThe four main groups of rocks of the Cadillac area- the Cadillac, Blake River, Kewagama or Pontiac, and Malartic- are found within the boundaries of the property. However, as these rocks have been fully described in · various government reports (1,2,3,4,5,6) and all the known orebodies occur within one group- the Blake River-a detailed description of the geology will be dispensed with here. The known ore deposits lie south of the Cadillac 'break' in a group of rocks that includes 'greenstones', greywackes, conglomerate, porphyries, and a rock of gabbroic composition that may be intrusive. Both flows and tuffs can be recognized in the 'greenstones'. The two bands of porphyry that trend easterly across most of the property have been considered by some observers to be dyke rocks and by others to be flows. Certain evidence points to their being dykes that were intruded as sills considerably prior to the emplacement of the gold-bearing veins, but the possibility of flow origin cannot be fully rejected. North of the talc-chlorite-carbonate schist zone forming the 'break' the rocks are conglomerate and greywacke with iron formation, in which there are no known veins of ore grade. Within the schist zone are minor acid and basic intrusives. The general trend of both bedding and schistosity is a few degrees south of east. The dip is generally vertica1 or steep to the south."

Jan 1, 1954

By J. R. Kastler

It becomes my pleasant duty to call the meeting to order. This is our fiftieth regular meeting. And the session we are opening today, I am sure: will be as interesting and informative as those in the past. These gatherings present a fruitful opportunity for an exchange of experiences and ideas that will aid all of us in our work in the various segments within the coal industry. Walter Johnson and his Program Committee have arranged a wonderful program for us; Walter, due to his standing in the industry and his large acquaintanceship with the leaders of the industry, has really gone to town in bringing outstanding speakers and personalities to deliberate with us in our proceedings. A lot of things have happened since we last met; in the operating end, and in safety we have made marvellous headway, but we have slipped badly in the marketing end. However, I am sure the messages and discussion you will hear will point out ways and means of overcoming at least some of our difficulties. Before we get on with the program, I want to thank our hard working Secretary, Fred Whiteside, who, by the way, is a charter member of the Institute and has attended every one of the fifty meetings we have held; and the various committees who have been meeting for the past several months and who have arranged this fine program you are to hear. I hope all of you enjoy the convention; the business as well as the social sessions.

Jan 1, 1954

By V. J. Lynch, A. L. Peyton

"INTRODUCTION AND SUMMARYThe Brewer mine, near Jefferson, Chesterfield County, S.C., was originally operated as a gold mines as late as 1890 this mine was reported to have been one of the large gold producers in the southeast,Occurrence of topaz on the Brewer property was not reported until 1935, when it was discovered by Pardee and Parks. 3/ of the Federal Geological Survey while they were investigating gold deposits in the Piedmont province.During the 1940's the Chemical Engineering Branch of the Tennessee Valley Authority and the Electrotecbnical Laboratory of the Bureau of Mines at Norris, Tenn., investigated topaz from the Brewer mine to determine the possibilities of its use as mullite and for the production of calcium fluoride.From July 1950 through. April 1951 the Bureau of Mines conducted a diamond-drilling project at the Brewer mine to determine the grade and extent of the topaz deposits. Ten diamond-drill holes, totaling 2,344 feet, were completed, and 231 analyses of core samples were made during the course of the project.This report presents factual data relating only to the diamond-drilling project, The placer deposits on the Brewer property were previously investigated by the Federal Geological Survey 4/."

Aug 1, 1953

By J. R. Thoenen, B. H. Clemmons, A. H. Reed

"INTRODUCTION AND SUMMARYOverall red-ore reserves in the Birmingham, Ala., area were estimated in 1910 by E. F. Burchard 4/. Since then mining has progressed into areas classed by Burchard as ""unavailable for exploitation"" under conditions existing at that time. This is understandable when it is considered that red iron ore was valued at $1.19 a gross ton at the mine in Birmingham in 19102/ and by 1948 had risen 300 percent; 6/ that skips had replaced cars in slope haulage; that mechanical loading and rubber-tired haulage had replaced hand loading and mule or locomotive haulage; and that other more efficient mining methods had been introduced. Intensive study during the intervening 40 years has been given to ways and means for upgrading the low-grade ores in the area and combining or blending them with raw red and brown ores for improved blast-furnace feed.It is reasonable to expect that future progress in mining efficiency and increased knowledge of the beneficiation characteristics of marginal ores will permit extraction of red-iron minerals now considered uneconomic.The Bureau of Mines has undertaken to restudy iron-ore reserves of the Birmingham area to determine what tonnage and grades of mineral are present; what is necessary to make them amenable to mining; what further advancement is possible in beneficia¬tion methods; and where increased production may be obtained in the area if and when required. This study has been underway for the past 2 years, but research into the beneficiation of marginal ores has been in progress at the Southern Experiment Station for the past 30 years. Many results of that research have been adopted in commercial practice in the area. Other results have not been published but are pre¬sented here in condensed form as an important factor in assessing marginal deposits with respect to their importance as ore reserves.An interim discussion of the salient features of past history and progress, as well as the data developed during the years of research in beneficiation at this station and the present field investigation, will make for a better understanding of the present position as well as be useful in evaluating future potentialities. Discussion in this paper is confined to the main Birmingham Basin area, which contains the largest concentration of hematite ores in the district."

Jul 1, 1953

By J. L. Eakin, J. P. Powell

"The increased costs of exploration and drilling of new oil fields and the continued success of water flooding in nearly depleted oil fields have created a demand for information on the results obtained from individual projects. The Bureau of Mines has published several reports concerning water-flood activity in the Midcontinent area and at the request of the industry has continued to collect and disseminate this information. This report was written in response to these requests. It describes in detail the water-flooding projects in Anderson, Franklin, Linn, and Miami Counties, Kans., and includes methods of water treating and the results obtained. The production histories of each county and many water-flood projects are shown graphically from the date of the first development. Maps of most of the major projects, showing their status as of January 1, 1953 are presented also.The practice of injecting water to stimulate oil production was legalized in Kansas in 1935, and the first water-flooding project authorized in this four-county area was initiated by the Texas Co. in December 1935 in Linn County. Forty-nine projects2/ initiated in the area to January 1953 are estimated to have recovered approximately 10 million barrels of oil that would not have been produced by methods used previously. About 7,900 productive acres had been, or are, flooded by these projects, and approximately 136 million barrels of water had been injected.These four counties in the eastern Kansas shallow production area3/ were an important factor in the early history of the Kansas oil and gas industry. This position has been maintained from the very beginning through the early period of vacuum and air injection and into the era of water flooding. The location of the area and the relative position of the four counties and water-flooding areas in each are shown in figure 1.The first drilling for oil in this area in 1860 resulted from investigations of the existence, and use by the Indians, of so-called tar or oil springs. The first wells drilled were nonproductive, and the impending Civil War caused the search for oil to be discontinued. In 1884 a few shallow oil wells were drilled near Paola, and completion of several gas wells near that city led to subsequent drilling of an oil well, which was completed in June 1885, having an initial flow of 10 barrels of oil daily.In 1904 the original Paola gas field became a good oil-producing field. In 1905 the Rantoul field in Franklin and Miami Counties was opened; and drilling activity spread throughout the adjoining area, resulting in development of several shallow oil pools in Linn and Anderson Counties. The first ""shoestring"" pool in eastern Kansas to produce oil was probably the Paola or Pressonville shoestring, which was discovered in 1917. The rate of oil production from the area declined until 1919, when the Centerville shoestring pool was discovered. Discovery of the Colony gas field in 1921 was followed within a few months by drilling of the Garnett and Garnett and bush City shoestring pools. The Schermerhorn pool (now part of the Centerville field) s discovered in 1927, and the Kincaid shoestring pool was first drilled in 1931. The oil-production histories of the individual counties are discussed separately."

Jun 1, 1953

By Vernon C. Davis

"SUMMARY AND CONCLUSIONSIn initial attempts to mine taconite by conventional open-pit methods, the material tended to break into tabular blocks that were too large to be handled by conventional shovel dippers and were unsatisfactory in an ordinary crusher feed. A great amount of secondary blasting was necessary, which added considerably to the cost of mining.The Bureau of Mines and others are engaged in studies designed to contribute to the solution of taconite-mining problems. These studies concern problems related to drilling techniques and patterns, types and methods of use of explosives, and other factors relative to effecting maximum fragmentation at minimum cost.This report is concerned with study of the application of shaped charges in drill holes, the effectiveness of shaped charges as compared to capped charges in secondary blasting, and the merits of different drilling patterns and methods of detonation of conventional-explosive charges.Fragmentation of taconite at or near the surface is controlled or strongly influenced by joint and bedding planes. Since all tests in this study were made in a jointed and bedded area, a definite conclusion as to the relative effect of a shaped charge in a drill hole, as compared to a conventional charge at greater depths and tighter ground, is precluded. However, application of shaped charges in primary blasting of taconite appears to be of no advantage.In secondary blasting of taconite, conventional, capped charges produced better breakage than shaped charges of the designs tested.Based on the results of conventional blasting practice in horizontal-, inclined-, and vertical-hole tests, no better fragmentation is obtained from blasting either horizontal or inclined holes, compared to vertical holes.Holes drilled in staggered parallel rows that intersect both series of joint planes at the greatest possible angle, give maximum breakage compared to rows parallel to one of the series of joint planes.Methods of detonation made little difference in breakage; but the millidelay caps produced the best conditions for moving the broken rocks."

Jun 1, 1953

By L. A. Panek, A. J. Barry, John A. McCormick

"INTRODUCTION During recent years, roof bolting has become widely accepted as a systematic method of supporting both coal- and metal-mine roofs. Today, over 2 million roof bolts are installed monthly. Most of the information on bolt installation procedure reported to date (1,2,3,4,5,6) 3/ has been obtained by trial and error by individual groups or operators. To insure good roof control, experience and field tests have indicated that roof bolts should be installed immediately after the exposure of new roof, and they should be preloaded enough to minimize sag of the roof over the opening. The question of the proper initial preload for roof bolts is under study, although it is a general practice to impose an initial load on a bolt of approximately 10,000 pounds. This created a problem of measuring bolt loads at installations in underground mines, which was partly solved by using a commercial-type torque wrench; a device that permits a direct reading of the torque applied to the nut on a roof-bolt assembly from which the corresponding load can be determined by referring to specifications furnished by the manufacturers. However, considerable apprehension was expressed regarding the accuracy of this measuring procedure because of variations in the manufacture of roof-bolting materials and the degree of care exercised in making bolt installations. In the process of loading a bolt, only a small part of the effort is expended in producing strain in the bolt - the larger part of the effort is used in overcoming frictional effects in the nut-bolt-washer assembly. These frictional effects are subject to many factors, such as condition of threads, type of lubrication, if any, the finish on the nut and bearing plate, and the alinement of the bearing plate on the bolt. The object of this investigation was to determine the accuracy with which the load developed in a slotted-type roof bolt installed in a conventional manner in shale or sandstone roof rock can be determined from the torque applied to the nut.This report is the first of a series relating to basic research in roof bolting in underground mines. A future report will cover results obtained using expansion-type bolts under similar conditions. Other reports will consider the efficiency of bolt anchorages, the long period stability of bolts, and the design of safe and efficient roof-bolting systems."

May 1, 1953

By Manuel Gomez, V. F. Parry, John B. Goodman

"INTRODUCTION The need for an accurate and precise analytical method for determining moisture in coals of high water content has been recognized by the coal industry as well as the fuel technologist. Interest in this particular phase of coal technology extends back to the early work of German investigators on the brown coals of Central Europe. Studies by these workers led to the establishment of a direct immiscible liquid-distillation method 4/ as the accepted moisture determining technique in European laboratories. Direct moisture determining methods, those methods that utilize various techniques to drive off the water from a given sample of coal and either collect the water in a calibrated receiver or selectively trap the water driven off in a suitable absorber, have found little favor in the United States. They have been treated merely as research tools.5/ The problem of moisture determination in low-rank coals of the United States has not been given much consideration because such coals contribute only about 2 percent of the total United States production. With renewed activity in low-temperature carbonization and with the growth of interest in coal and coal-tar hydrogenation, the American coals of lover rank containing 20 to 40 percent bed moisture will be subjected to extensive investigation. If the low-rank coals of the United States are to be accurately appraised, the need for qualitative and quantitative analytical proceeded becomes more pronounced. These coals, especially the lignites of Texas and North Dakota, are highly susceptible to oxidation, a process that proceeds to a greater or less extort when low-rank, high-moisture coals are treated by oven-drying methods. The extent of this atmospheric oxidation has been described and evaluated by numerous workers. 7/In many respects, the problem of moisture determination in low-rank coals, those found in the United States and the high-moisture coals of Central Europe, is similar. Conversely, the problem of moisture determination assumes a different aspect when the coals of the eastern and the middle-west sections of the United States are considered. Present methods, the loss in weight gravimetic-type procedures, serve adequately to test these low-moisture coals. The determination of moisture in coals containing 20 to 40 percent water should be approached from a direct method rather than from an indirect gravimetic-type procedure because of the oxidative tendencies of these coals and the demonstratrated inability of a loss-in-weight technique to remove all the water in a given sample of coal."

May 1, 1953

By W. H. Ode, W. A. Selvig

"INTR0DUCTIONAccording to the Standard Specifications for Classification of Coals by Rank of the American Society for Testing Materials (A.S.T.M. Designation: D388-38).1/ high-volatile bituminous coals, subbituminous coals, and lignites are classified on the basis of calorific values on the ""moist"", mineral-matter-free basis. The moist basis refers to coal containing its natural bed moisture but not including visible water on the surface of the coal. It is assumed that the natural bed moisture of coal in the ground represents the moisture-holding capacity of the coal when in equilibrium with air at approximately 100 percent relative humidity. This moisture is sometimes referred to as inherent moisture as opposed to extraneous moisture, which wets the surface of the coal.To simplify procedures for determining the moisture-holding capacity of coal it is assumed, for all practical purposes that the moisture content of coal when brought to a standard condition of moisture equilibrium in an atmosphere of 97 percent relative humidity and 300 C. represents the bed moisture of the coal. The A.3.T.M. specifications provide that this condition of moisture equilibrium shall be obtained by bringing the coal to a standard condition of moisture equilibrium at 300 C. in a vacuum desiccator containing a saturated solution of potassium sulfate (97 percent relative humidity) according to the procedure proposed by Stanfield and Gilbart. 4/ No mention is made in the specifications for bringing partly air-dried samples to their natural bed moisture condition probably because of the hysteresis effect that has been noted by various investigators. 5/ In this connection it has been found from sorption studies that the adsorption and desorption curves for lignite are not entirely reversible. The hysteresis effect has been explained by some investigators as resulting from shrinkage of the lignite during drying, which causes a collapse of some of the capillaries, so the dried lignite cannot take up as much water as it held originally."

Apr 1, 1953

By Wing G. Agnew, Paul L. Russell

"INTRODUCTION During the past few years, the development of millisecond-delay electric blasting caps has made possible a more flexible control over timing the firing of individual charges in blasting, The use of these caps has proved especially productive in quarry blasting and in numerous construction operations, but their use in underground mining is developing more slowly, although in some cases, as the solution to a difficult breaking problem, they have been well-received. When used in metal-mine drifts, the general objection is that the broken rock is thrown too far. In nearly all cases, however, use of millisecond-delay caps results in better fragmentation of the rock and a lower powder consumption per ton of rock broken.Prom 1949 to 1952, several series of experiments were conducted at the Mount Weather, Va., Experimental mine in conjunction with driving a 6- by 10-toot ventilation raise. 3/4/ The raise-round experiments in this 238-foot shaft, using millisecond-delay electric blasting caps in various drill-round patterns, are the subject of this report.SUMMARY AND CONCLUSIONSAll rounds discussed in this report were drilled in the hard rock (epidosite and greenstone) of the ventilation raise at Mount Weather Experimental mine (figs. 1 and 2). The drill-round patterns varied from 28- to 32 holes and from a V-cut design to one having no cut boles at all. With the exception of the first two rounds, all blasting was done with millisecond-delay electric blasting caps. In all rounds 60-percent ammonia gelatin dynamite was used and holes were stemmed with two cartridges of sand stemming."

Apr 1, 1953