Search Documents

By F. E. Steigert, A. H. Geisler

THE permanent magnet alloy comol, which contains 17 pct Mo, 12 pct Co, balance Fe, exhibits a precipitation reaction analogous to that at the iron end of the binary Fe-Mo system. The equilibrium precipitate, (P,), has a structure isomorphous with Fe,Mo, which is rhombohedra1 with parameters a = 8.97A and a = 3038.6&apos; according to the work of Arnfelt and Westgren.&apos; In the ternary alloy the parameters are a = 8.87A and a = 31°0.5&apos;. Oscillating crystal patterns of a single matrix crystal, M, in which P, was precipitated by slow cooling from 1300°C, showed that the orientation relationship of the two lattices is as follows: (110)P3 // (110)* (111)p3 // (110)m There are crystallites of P, in 12 different orientations in a single crystal of the parent solid solution. Microscopic examination shows that the crystallites are generally plate-like with their lateral dimensions parallel to (110) matrix planes. When precipitation in a supersaturated alloy quenched from 1300°C progressed isothermally at temperatures between 600" to 800°C, the evolution of the P, structure could be traced. Diffuse diffraction effects in Laue patterns provided early evidence of the precipitation process. Analyses of these by a previously described technique2 showed that they corresponded to rod-like elements parallel to <110> matrix directions in reciprocal space. With further aging to promote growth of the precipitate, the rod-like elements contracted to points in reciprocal space for normal Bragg reflection from the precipitate as shown by the left diagram in Fig. 1. Thus the diffuse scattering was attributed to the small thickness of the plate-like particles which was inadequate for sharp diffraction. When the precipitate particles were first thick enough to give normal diffraction their structure was different from that of the equilibrium precipitate, P,. The first structure, P1, presumably is a coherent transition struc-

Jan 1, 1952

By N. J. Grant, W. R. Opie

THE amount of hydrogen that will dissolve in lead has been considered negligible. However, a limited number of measurements made recently using apparatus built for determining hydrogen solubility in aluminum alloys&apos; indicate that liquid lead will hold a small but appreciable amount of hydrogen in solution. The apparatus used was similar to that developed by Sieverts.&apos; This consists of a bulb to hold the molten metal, a gas burette for introducing a measured quantity of gas into the bulb and a manometer for measuring the gas pressure in the bulb. Measurements are made by introducing enough of an insoluble gas (helium) to fill the system at a given temperature and pressure, thereby determining the hot volume of the bulb. This gas then is pumped out and hydrogen is introduced until the same pressure is reached, the metal being maintained at the same temperature while in contact with each gas. The difference between the volumes corrected for pressure is then the hydrogen solubility. A more detailed account of the procedure can be found in refs. 1 and 2. The lead was melted in an alundum crucible by induction heating to provide uniform temperature and an important stirring effect. The metal was the purest obtainable, 99.999 + , prepared especially by the research department of the American Smelting and Refining Co. Measurements were made by approaching the equilibrium value from high and low temperatures during the constant pressure runs, and from high and low pressures when the temperature was held constant. Thus a number of measurements were made on each of two large samples which weighed 336 and 398 g. The gases were purified as .described in ref. 1. The effect of temperature on the solubility was studied with the pressure held constant at 760 mm of Hg. To show the effect of pressure, solubility measurements were taken at two constant temperatures, 600" and 900°C. Results The effect of temperature on hydrogen solubility is shown in Fig. 1. The curve representing the data is parabolic, as are plots of hydrogen solubility vs. temperature for other metals and alloys (aluminum,&apos; copper," and iron,& for example). Fig. 2 shows the relationship that exists when the solubility is

Jan 1, 1952

By W. B. Dingle

"IntroductionMANY PAPERS presented on developments in the Canadian Petroleum Industry •during the past few years have commenced with this general sentence: ""The past year has been a record •one for the oil industry in Canada, with new records being set in nearly all phases •of exploration and development ,activity"". This sentence applies equally well to 1951. It is not possible to outline all the details of the broken records in exploration, development, and production but general comparisons can be made. There are several significant developments that have stolen the spotlight during 1951, some of which were foreseen in 1950 and some which were not. Among the high-lights were the following:(1) The greatly •expanded activity in the search for gas, which was touched off by the new Alberta regulations covering gas leases and reservations.(2) The discovery of commercial oil production in the Williston basin of North Dakota and Manitoba, which will have far reaching effects on Canadian oil.(3) The greatly increased activity in northern Alberta, northwestern British Columbia, the southern Northwest Territories, Saskatchewan, and Manitoba.(4) The new discoveries in the general central Alberta area.(5) The granting •of a permit for an oil pipeline to the Pacific coast.(6) The arrival of Western Canadian crude in central Ontario.(7) The number of new refineries completed, commenced, or proposed.(8) The present •and proposed expansion in the petrochemical industry.Most of the remarks made on various exploration and development •activities will refer to Western Canada operations, primarily because the greatest •activity and the most significant developments have been there. Eastern Canada exploration and development operations were at a slightly higher level than in 1950."

Jan 1, 1952

By W. M. Goodwin

"IntroductionIN THE preceding paper we have learned about Canada's resources of metallurgical coal. There is an adequate amount in Nova Scotia, a very large reserve on the eastern flank of the Rocky mountains, and a strictly limited supply on the Pacific coast. Added to these is an unknown quantity of coking coal in the Peace River district, at present rather isolated but possibly capable of industrial development in the future.The chief use of metallurgical coal is to make iron and steel. For this, an adequate supply of iron ore is required. So we should now scan the Canadian supply of iron ore, the possibility of its increasing use at home, and the probable markets abroad.Trade in iron ore tends to be international, as is the case with many other raw materials. The present tendency with iron and steel, in contrast, is to keep its manufacture within national boundaries, and there is no evidence that this will change much in the years to come. We should keep these two points clearly in mind when considering the disposal of iron ore from Canadian mines. We should remember, also, that the modern blast furnace and steel plant has such a large output that a correspondingly large population, reasonably compact, is needed to consume its products.Large Ore Supply in East, Small in WestCanada has now four major iron ore fields, well situated to serve adequately the eastern half of the country. Wabana .and Labrador are well placed to serve overseas markets and plants on the eastern seaboard and eastern interior of the United States and Canada."

Jan 1, 1952

By Julian Glasser, Arthur Fleischer

THIS country was faced with the possible necessity of utilizing nonbauxitic ores for producing aluminum during World War 11. Construction of four experimental plants to treat such ores by four different processes was authorized1-4 including one at Salt Lake City, for the conversion of Marysvale alunite to metal-grade alumina and potassium sulphate by the Kalunite process.&apos; An aluminum reduction plant in Tacoma, Wash., with a capacity of 50 tons of aluminum per day, was constructed to handle the Kalunite alumina produced at the Salt Lake City plant. The alumina and aluminum plants were Defense Plant Corp. projects operated by Kalunite, Inc. and Olin Industries, Inc., respectively. Kalunite alumina differs from Bayer alumina in several respects, particularly in that the former contains potash instead of soda. The presence of potassium in the alumina feed to the cryolite bath was stated by aluminum technologists to be undesirable under the usual operating conditions of aluminum furnaces. In 1940, about 20 tons of Kalunite alumina produced in the Kalunite pilot plant, were reduced electrolytically in a 10,000 amp furnace at Battelle Memorial Institute and at the aluminum reduction plant at Neuhausen, Switzerland. These relatively small scale tests indicated that satisfactory commercial aluminum could be produced in a practical manner. The Tacoma plant reduced about 2,500,000 lb of Kalunite alumina to produce more than 1,200,000 lb of aluminum, in accordance with the accepted gractice for reducing Bayer alumina. It was desired to determine whether commercial aluminum could be produced on a large scale and to establish the technological differences in commercial reduction practice between Kalunite and Bayer alumina. In the course of collecting data, the effects of the abnormal chemical composition and physical properties of Kalunite alumina were observed wherever possible. Tacoma Reduction Plant The reduction plant had two pot lines, each with 120 cells in series, operated at approximately 32,000 amp. Each cell was provided with a single rectangular Soederberg continuous anode, with side-pin electrical contacts. Each cell was hooded and ventilated through a stack connected to 14 other cells, with 25,000 cfm blower. When the plant started operation in 1942, all of the cathode linings were of block construction. Rebuilt cells were of rammed paste construction.

Jan 1, 1952

By N. E. Hanna

To be authorized for use in coal mines, explosives and blasting devices must pass certain safety tests prescribed in schedule 1F,3/ on the basis of extensive practical and theoretical research by the Explosives Testing Station of the Federal Bureau of Mines. An explosive or blasting device that passes these tests is placed on the active permissible list. As this list is constantly revised, it has been the practice of the Bureau of Mines periodically to publish the names of explosives and blasting devices that have been added to the active list, as well as those that have been transferred to the inactive list; changes in brand names also are reported. This circular covers all permissibles including additions, transfers, and changes made between December 31, 1945,4/ and December 31, 1951.

Jan 1, 1952

By R. J. Hundhausen

The Shamrock copper-nickel mine in Jackson County, Oreg., was formerly a part of the Chisholm mercury property. In 1948 new owners advanced the old workings 40 feet to reveal encouraging widths of copper-nickel sulfide, ore on the Shamrock claim. When the owner&apos;s funds became exhausted, the Bureau of Mines carried on the development in 1949-50, completing 1,650 feet of bulldozing trenching, 396 feet of drifting, and 3,419 feet of diamond drilling. The Bureau&apos;s trenching disclosed a separate surface deposit 600 feet south of the mine deposit. This and the previously known deposit subsequently were diamond-drilled. The underground deposit has a known length of 100 feet, a dip length of. 100 feet and a width varying from 1 to 25 feet. The surface deposit is 200 feet long, 200 feet deep, and 5 to 38 feet wide. Neither deposit has been entirely delimited by development to date.

Jan 1, 1952

By L. E. Djingheuzian

Introduction For many years the immense deposits of bituminous sands of northern Alberta have been attracting the attention of our governments, engineers and .scientists ( 6). Undoubtedly these bituminous sands represent one of the greatest potential resources of liquid fuels in the world. However, their commercial development has been retarded by the complexities of the technological problem and by the economic factors involved in the processing of the sands. The technological problem has been attacked from several angles ( 2, 3, 1, 11), and cold water separation of bitumen is one of them. To the ore dressing engineer, the cold water process is of utmost importance since, by the use of standard ore dressing machinery, it accomplishes most efficiently and economically the separation of bitumen from bituminous sands. The significance of using ore dressing equipment was especially enhanced by the fact that the scientific principles which underlie the design of standard machines were demonstrated in the cold water separation process with an extraordinary clarity. This greatly facilitated the analysing of limitations and advantages of different machines during-the pilot plant investigations and helped to complete the investigations practically in the allotted time.

Jan 1, 1952

By Orville R. Lyons

CENTRIFUGAL force has been utilized for the dewatering of fine coal for over 50 years by means of machines commonly called centrifugal dryers. In any centrifuge the coal and water are subjected to a spinning action which usually inctedtocreases in intensity as the coal progresses through the machine. This spinning action, or the centrifugal force that it induces, tears water away from coal particles and produces a dewatered coal. The effectiveness of the dewatering action for any particular machine is governed by the size-consist of the coal and the centrifugal force imparted to the water on the coal. Four makes of centrifuge are currently being used to dewater fine bituminous coal in the United States. These include the vertical, basket-screen C.M.I. (Centrifugal and Mechanical Industries) Carpenter, Reineveld, and the horizontal solid-bowl Bird. The C.M.I. and Reineveld centrifuges are similar in construction and are variations of the Elmore centrifuge, varying principally in the slope of the basket, operating speed, size of perforations in the basket, and diameter of the basket. The same operating description suffices for both. These centrifuges are made up of two rotating elements, an outside conical screen frame and an inside solid cone which carries spiral pusher blades. The screen frame is supported by a hollow shaft, and the solid cone by a spindle shaft passing through the hollow shaft. Both the screen frame and the solid cone rotate at high speeds; the solid cone, with its scraping flights, rotating somewhat more slowly than the screen. The wet coal enters the machine at the top, falls on the cone, and is thrown against the screen by centrifugal force. The coal slides down the screen until it meets the upper end of the flights, where it is moved slowly along the flights until discharged at the bottom. The elfluent passes through the sieve basket or screen and discharges into a launder. The Carpenter centrifuge consists of a conical rotating element with a vertical axis, built up of three rows of perforated stainless-steel plates or stainless-steel wedge-wire or round-wire sections cut and rolled to conform to the surface of the cone. Wet material is delivered to a conical hopper inside the centrifuge casing and is distributed in a thin, even layer over the inner surface of the cone by a disk mounted on the rotor shaft. Impacting of the coal against the screen and the centrifugal force exerted as the material moves downwards creates a dewatering effect. The moisture is forced through the coal bed and then through the perforated plates of the basket, collecting in a circular trough built into the centrifuge. The effluent is conducted from the trough through the centrifuge casing by outlet pipes. The dewatered coal is discharged over the inside bottom edge of the rotor. The Bird centrifuge consists of a tank or truncated conical shell, which is revolved at the desired speed by means of a drive sheave. A screw conveyor rotates inside the cone or bowl at a slightly lower speed in the same direction of rotation. The feed entrance, in the center of the large end of the truncated cone, is high enough to allow formation of a pool of slurry. Adjustable effluent-discharge ports are located in the large end of the bowl so the level of the liquid can be regulated. The solids are moved forward by the screw conveyor as fast as deposited and carried above the level of the pool for an interval before leaving the bowl. In the past these four makes of centrifuge could be compared only by indirect means. The author published a rough comparison method in 1949&apos; but

Jan 1, 1952

By A. E. Powers, J. F. Libsch

THE simultaneous influence of time and temperature upon the tempering process in steel is well known. Hollomon and Jaffe¹ have expressed the effect of time and temperature upon the progress of tempering by a single parameter, T (c + log t); where T is the absolute temperature; t, the tempering time; and c, a constant characteristic of the steel and treatment. It was found that when hardness data for plain carbon and low alloy steels were plotted vs. this parameter, a master tempering curve was obtained which satisfied all the data for a given steel and a given hardening treatment. Roberts, Grobe, and Moersch² successfully applied the tempering parameter to various tool steels, including high speed steel for tempering times ranging from 6 min to 100 hr. The influence of tempering time and temperature upon the physical properties of high speed steel has also been extensively investigated.&apos;" Recently, the use of induction heating for very rapid tempering treatments has received attention. The authors% have shown that tempering treatments of only a few seconds duration may be successfully applied to plain carbon and low alloy steel. However, the influence of such short tempering treatments in high speed steel has not been explored. Since high speed steel is a highly alloyed steel exhibiting physical reactions during tempering that are often relatively slow and large in magnitude, it is an interesting steel for the study of tempering reactions. It was the purpose of the present investigation, therefore, to study the early progress of reactions leading to secondary hardness in high speed steel, type 6-5-4-2, and to determine if induction-tempering treatments of a few seconds duration are able to produce results equal to those of more conventional long-time tempering cycles. Experimental Details The chemical compositions for two different heats of W-Mo high speed steel used in this study are given in Table I. Table II summarizes the heat treatment given various groups of specimens cut 21/2 in. long and centerless ground to ¼ in. diam. Hardening treatments consisted of preheating to 1600°F (870°C) for V2 hr and then oil quenching from 2250°F (1230°C). Heat I was subjected to the high temperature in a salt bath for 3 min, while specimens of heat II were austenitized in a carbon-block muffle furnace for 10 min. Specimens of series E were immediately refrigerated to — 318°F (— 195°C) in liquid nitrogen following the hardening treatment to transform the major portion of the retained aus-tenite. Specimens of series F and G were subzero cooled to — 100°F (-75°C) in a dry ice-alcohol mixture. Induction tempering was performed with a Lepel high frequency converter operating at a frequency of approximately 300,000 cycles per sec. Heating cycles were controlled and recorded for each specimen using a chromel-alumel thermocouple, percussion welded to the surface of the specimen, and a modified high speed instrument with a timer previously used and described.&apos; Temperature oscillation of the specimens, while being held at the tempering temperature, was ± 15°F (8°C). Tempering Treatments: After hardening, specimens were tempered between 900" and 1500°F (480" and 815°C) to study the progress of retained austenite decomposition and secondary hardening. The specimens tempered in salt for 1 hr (series C, G, and I) were considered to represent conventional treatment and are used for comparison with rapid tempering treatments. Several induction-tempering cycles were employed: 1—flash tempering, i.e., induction heating to the tempering temperature and immediately cooling (series A, E, and F); 2—induction heating for 60 sec at temperature (series B); and 3—double-induction tempering by two successive heating and cooling cycles (series D). All specimens tempered by induction were heated at an initial rate of 450°F (250°C) per sec except those of series E, which were heated at an initial rate of 1300 °F

Jan 1, 1952

[1.1. The provisions of this code are minimum provisions and are designed to minimize hazards to life and property in and about underground coal mines where electrical equipment and circuits installed used. They indicate the Steps necessary in the selection, installation, operation, inspection, and maintenance of electrical equipment and circuits to obtain proper safeguards in reducing electric shock, fire, explosion and other hazards. Surface as well as underground installations were considered in formulating the code and, unless otherwise stated, each provision applies equal to both underground and surface installations. This code does not apply to buildings and installations not directly connected with mining operations, nor does apply to strip-mining operations.]

Jan 1, 1952

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory state of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which are useful for predicting machine performance and give, acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary in commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed&apos; in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted. In its first form, as stated by P. R. Rittinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include .the concept of surface energy; in this form it was precisely stated by A. M. Gaudin2 as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended. According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps, 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported&apos; that support the theory in its first form by indicating that the new surface produced in. different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work" done on. the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading since it does not follow the regular breakage pattern of most materials but is relatively harder to grind at the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory&apos; is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr/log 2.5 The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in. reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-1.5 If a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The&apos;evaluation in terms of kw-hr per net ton of 200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of -200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned, with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1952

By F. W. Schremp, V. L. Johnson

This paper discusses the results obtained from high temperature, high pressure filter loss studies in which field samples of clay-water, emulsion, and oil base fluids were used. High temperature, high pressure tests of some premium priced emrilsion and oil base drilling fluids show filter loss peculiarities that are not predicted by standard API tests. It is recommended that high temperature, high pressure filter loss tests be used to evaluate the performance of such fluids. Apparatus is described which proved to be satisfactory for evaluating filter loss behavior over a wide range of temperatures and pressures. INTRODUCTION The petroleum industry spends large sums of money each year on chemical treating agents for lowering filter loss and on premium-priced low filter loss drilling fluids. While it is an accepted fact that low filter loss is advantageous during drilling operations, it is questionable whether the present standard method of determining filter loss gives a reliable indication of the loss to he expected under bottom hole conditions. The purpose of this paper is to show that high temperature. high pressure filter loss tests Should be used to evaluate filter loss behavior of fluids for deep drilling. Concern over possible effects of filter loss on oil well drilling and well productivity dates back to the early 1920&apos;s. During the years 1922 to 1924, filtration studies were reported by Knapp,&apos; Anderson2 and Kirwan." These studies were the first to be reported in the literature on this subject. No further information was published on the subject until 1932 when Rubel&apos; presented a paper in which he discussed the effect of drilling fluids on oil well productivity. In 1935. .Jones and Babson constructed the first laboratory tester designed to study the effects of temperature and pressure on the filter loss behavior of clay-water drilling fluids. In a discussion of their investigations, Jones and Babsons stated, "Performance characteristics of a mud can he evaluated with considerable reliability by a single test at 2,000 psi and 200°F. Exact correlation between the results of performance test5 made under these conditions and the behavior of muds in actual drilling operations is of course impossible." Jones arid Babson apparently were well aware that at best laboratory tests can give only qualitative answers to the question of what is the actual behavior of a drilling fluid when subjected to deep drilling conditions. Jones&apos; presented a paper in 1937 in which he described a static filter loss tester to be used for routine filter loss tests. This instrument subsequently was adopted as the standard APl filter loss tester. In 1938, Larsen7 developed a relationship between filtrate volume and filtrate time that is in general acceptance today. Larsen was cognizant of the danger of estimating bottom hole behavior from filter loss measurements at room temperature. He tried to predict the effect of temperature on filter loss by relating temperature effects through the temperature dependence of filtrate viscosity. This was undoubtedly an over-sirriplification of the temperature dependence of drilling fluid filter loss. In 1940, Byck" published a summary of experimental results of filter loss tests made on six representative California clsy-water drilling fluids. He concluded that "no existing method will permit even an approximate determination of the filtration rate at high temperature from data at room temperature. It is necessary to measure filtration at the temperature actually anticipated in the well, or to make a sufficient number of tests at various lower temperatures so that a small extrapolation of these data to the anticipated well temperature may be applied." Byck&apos;s findings were presuma1)ly well accepted and recognized by drilling Fluid technologists, and yet, they did not lead to wide adoption of high temperature drilling fluid filtration equipment. This is evidenced by the fact that no addition information has appeared in print on the subject since 194). Study of Byck&apos;s data shows that there was a useful consistency in them. The fluids did not show predictable losses at high temperatures, but they did line up at high temperatures in approximately the same order that they lined up at low temperatures. That is, if a fluid appeared to be a good fluid with relatively low loss at low temperatures, it would also be a good fluid with relatively low loss at high temperatures. In the last decade. the above situation has changed. The drilling fluid art is markedly different from what it was. The outstanding change, as far as the present discussion is concerned, has been the adoption of wholly new types of drilling fluids. Oil base and emulsion drilling fluids have come in to wide use. It is, therefore, necessary- to re-examine previously satisfactory generalizations to see if they are still valid. It turns out. as might have been expected. that Byck&apos;s explicit generalization. already quoted, is still true. Filter losses at high temperatures cannot be predicted from filter losses at low temperatures. However, no further generalizations are valid now. Fluids of different chemical types show different general behaviors. No longer do the fluids line up approximately the same at high temperatures as they do at low temperatures. They may line up entirely differently. Special fluids exhibiting very low loss at low temperatures may have losses as high as those of ordinary clay-water fluids at high temperatures. This fact is highly significant, because premium prices are being paid for the special fluids.

Jan 1, 1952

By H. DeWitt Smith

THE disastrous effect of two major wars on foreign economic health is giving American capital opportunities which might have not otherwise developed. At a time when discovery of major orebodies in the United States awaits fuller application of new geophysical tools and technical methods, U. S. investors must seek other fields where investment may be put to work. The unsettling effects of war have made it almost impossible for foreign nationals to develop mineral wealth, permitting Americans to enter at a time when U. S. mining, with a few exceptions, is in the process of expanding known orebodies and developing only a few new ones. Available capital, however, is not the only pre- requisite for entering the foreign mineral development field. The capital must be able to work in favorable economic atmosphere, a condition not easily satisfied in a world constantly in a state of political and social flux. In many countries, the political theory changes as often as the wind direction in March. Thus, the political stability of the form of government is of prime importance to the investor. In addition, a balanced budget and a moderate tax structure are important. Because in making foreign investment it is inevitable that one will have dealings with government officials, it is basic that they must be of high integrity. In countries filling the requirements, it will usually be found that the economic initiative of the individual is respected. Newmont Mining Corp.&apos;s three major investments in the last 15 years have been in Canada and the

Jan 1, 1952

By A. P. Svenningsen

IN the early stages of design it was not considered necessary that separate crushing plants be built for the new sulphide concentrator and smelter until sometime in the future. The plan was to use the existing crushing facilities for both oxide and sulphide ore. A few additions were contemplated for the existing plants, such as increased bin capacity, and possibly two new secondary crushing units. The more the problem was studied and discussed with the plant operators, the more it became evident that it was complex. It involved the classification of different kinds of ore from the open pit mine -sulphide, oxide and mixed-and how best to separate them so that each kind of ore was given the proper processing and treatment. It also involved the problem of keeping the different ores from being contaminated in bins, hoppers and chutes. Added to these, transportation became complicated and would involve additional handling and loading of ore from crushing plants to conveyors, to bins, and finally to railroad cars which were to be hauled to the concentrator and dumped into the fine ore bin. General In the early part of 1951 it was decided that the concentrator be constructed with ten grinding units instead of seven as originally authorized. The smelter was to be increased proportionally and naturally also the overall tonnages of ore to be handled by the new sulphide plant. Due to this increase in plant capacity and the larger tonnages involved, the difficulties which would arise by using the existing crushing plants were increased to a point where it became evident that the building of new crushing plants for sulphide ore exclusively was technically, as well as economically, advantageous. Authorization was, therefore, given by the company to construct new crushing plants to handle 30,000 tons of ore per day, and capable of reducing the run-of-open-pit ore to the proper size feed for the 10x14-ft rod mills in the concentrator. The ore, mined in the open pit, sometimes comes in pieces as large as 6 to 7 ft diam. The rod mills may call for ore crushed to 3/4 in. The large .size of ore delivered from the open pit determined that a 60-in. gyratory crusher be used as primary breaker. Such a crusher will have a capacity considerably in excess of 30,000 tons per day. The crusher will be a single discharge unit driven by a 500-hp electric motor through a tear coupling and a floating shaft. This type of drive has proven successful at a number of other crusher installations which our company has operating in the United States, Mexico and South America. The tear coupling will protect both the crusher and motor against damage in case of overload. No new features are incorporated in the design of the crusher itself, except that the, discharge chute is made the full width of the crusher with parallel sides instead of the usual converging sides. This change in detail should eliminate, a feature which has been a bottleneck in some of the operating plants and has caused loss of production due to ore hanging up and blocking the chute. The secondary crushing plants will have three 7-ft standard Symons cone crushers and six 7-ft short head Symons crushers. Between the primary and secondary crushing plants a coarse ore bin will be constructed with a nominal draw-off capacity of 30,000 tons of ore. The standard Symons and the short head Symons will be in separate buildings. All the crushing plants and the coarse ore bin are interconnected with conveyor belts for transporting the ore to the crushers at the tonnage rate desired. The final product of the new crushing plants is produced by the short head crushers. It will be delivered onto a conveyor belt leading to the top of the fines ore bin in the concentrator. A separate conveyor belt running the full length of the fines ore bin and provided with a movable tripper of rugged design will discharge the sulphide ore into the bin. The concentrator bin is planned and designed so that the installation of this additional conveyor will not interfere with the operation of the two railroad tracks on which crushed ore is brought from the existing oxide plant. Thus when completed the bin can be filled simultaneously by ore from the new crushing plant and by ore from the existing leaching plant.

Jan 1, 1952

By T. W. Wlodek

"AbstractThe results of research into the fatigue properties of SAE 1080 carbon steel and nickel-chromium-molylbdenum steel for mining drill rods are analysed and described in detail.The effect of water corrosion on the fatigue strength of drill rods of these two steels in the as-rolled condition has ,been investigated and the beneficial influence of shot-peening on their dry and water-corrosion fatigue strengths determined by employing the method developed previously (1).Eight S-N curves for as-rolled and shot-peened mining drill rods under both dry and water corrosion conditions have been derived and their shape and relative position are discussed. The main features relating to field performance of the drill rods are analysed.Purpose of Research and Outline of ProgrammeDRILLING holes in rock and ore by means of drill rods attached to a pneumatic drill is a basic procedure required in mining operations. Detonation of explosives placed in these holes is at present the only practical method of breaking down the rock and ore.A drilling rod is supported by its bit end in the drilled rock. Its shank end, fixed in the drilling machine, transmits impact energy to the cutting edges of the bit. On the field performance of the drill rod depend a number of basic mining operations such as sinking, drifting, and stoping. The drill rod is there-fore regarded as one of the most important tools used in the mining industry."

Jan 1, 1952

By Henry Schwellenbach

LABOR shortages, rising wages, and changes in moisture and fines content of the ore necessitated a review of the flowsheet at Warren Foundry & Pipe Co&apos;s. Mt. Hope, N. J. Mines Div. This plant had been designed prior to World War II, and started operations in January 1945. When this operation was designed there was an oversupply of labor in the area, wages were at a reasonable level, the run-of-mine ore was low in moisture, and there was a limited amount of fines. These factors all favored use of hand picking for cleaning rougher lump concentrate. Since that time, many changes have occurred. The proximity of defense industries and large military installations, has created one of the most acute labor shortages in the country. This labor shortage together with present wage levels, and the increase in moisture and fines in the ore created several problems. The increase in moisture and fines may be attributed to changed mining methods, the extensive use of sprays, and the opening of new mining areas bringing an increase in ground water. [ ] Two problems were presented by the increase in moisture and fines. The first was that lump ore arrived at the open hearth in an unacceptable condition, due to the segregation enroute of the large amount of fines that had adhered to the lumps. The second problem was that high magnetite content fines coated the large lumps, making it difficult for pickers to distinguish middling by other than the relative weight. [ ]

Jan 1, 1952

By R. F. Stevens

A laboratory method for examining crude shale oil is described. The method uses only about 500 ml. of sample and a limited number of analytical determinations. Results provide information on the general characteristics and composition of an oil and serve as a basis for comparing different oils. However, the method does not provide for direct estimates of yields of commercial products. Analyses of 10 oils produced in the United States by different methods of retorting and of 10 shale oils from commercial-scale operations in 6 foreign countries are given. The shale-oil-analysis method presented in this paper is based on and employs the same equipment as the Bureau of Mines routine method for analyzing crude petroleum. As shale oil contains groups of compounds not generally found in petroleum, several modifications of the petroleum method that might increase its suitability for application to shale oil were investigated. The modifications included in the present method take into account the apparent poor heat stability of shale oil and the presence of large quantities of olefins and nitrogen compounds.

Jan 1, 1952

By V. T. Stringfield, H. H. Cooper

ONE of the earliest investigations of ground water in Florida was made in 1513 when Ponce de Leon arrived at St. Augustine in search of the Fountain of Youth. The history of the development of the water resources of the State shows that the large artesian reservoir that underlies Florida was discovered in the latter part of the last century. Part of that history is given by L. C. Johnson&apos; who states that the first successful artesian well in Florida was drilled at St. Augustine between 1880 and 1882. After the City of Jacksonville failed to obtain a flow of artesian water at a depth of nearly 400 ft and abandoned the drilling, R. N. Ellis, City Engineer, and L. C. Johnson, using Johnson&apos;s knowledge of the geologic structure of the artesian reservoir, estimated correctly that artesian water could be obtained at a depth of about 500 ft. Thus began the development of the large artesian system in the northeastern part of the State. In 1908, the Florida Geological Survey issued its first report on the ground water of central Florida. More recent reports give the results of investigations that have been in progress in cooperation between the Florida Geological Survey and the U. S. Geological Survey since 1930. As a result, the ground-water geology and hydrology of Florida are now so well known that ground-water problems such as confronted early investigators no longer exist. However, new problems arise and new discoveries are made as the demand for more ground water increases with the development of the State. Water-Bearing Formations Descriptions of the geologic formations and a map showing their distribution at the surface are given in a recent report by Cooke.&apos; The geologic formations that yield the ground-water supplies in Florida represent only a small part (about 1000 ft) of the total thickness of the sedimentary rocks (more than 15,000 ft) that underlie Florida. The water-bearing rocks that yield fresh water include more than two dozen formations that range in age from Eocene to recent. The Eocene formations, which consist chiefly of limestone, are the oldest and the deepest of the formations in Florida that yield fresh water to wells. In 1944, on the basis of a study of the foraminifera, the Applins -ivided the limestone of Eocene age into six formations, which are as follows, from top to bottom: Age or group Formation Jackson Ocala limestone icAvon Park limestone Claiborne -j Tallahassee limestone aLake City limestone Wilcox Salt Mountain limestone xOldsmar limestone The Ocala limestone and the underlying formations of Claiborne age, along with some of the overlying limestone of Oligocene and Miocene age, constitute the principal source of water in Florida and southeastern Georgia and generally may be regarded as forming one artesian aquifer or water-bearing unit. This aquifer is referred to in this paper as the Floridan aquifer, a name proposed by Parker.&apos; In part of Seminole County alone more than 1000 flowing wells yield water from the Floridan aquifer. A yield of 6500 gpm, or about 9.5 million gal per day, by natural flow from a well penetrating the aquifer at Jacksonville, Florida, was observed in 1942. A yield of about 7000 gpm by natural flow was reported for a well 1390 ft deep at St. Augustine in 1887. The largest yield reported from a pumped well penetrating the aquifer is 7500 gpm, or about 10.5 million gal per day. The aquifer is also the source of some of the large springs, such as Silver Springs, whose discharge, according to measurements made by the U. S. Geological Survey, has ranged from 526 to 1350 sec-ft, or from 340 to 872 million gal per day. The top of the Ocala limestone, as represented by contours in Fig. 1, indicates in a general way the geologic structure of the formations that comprise the Floridan aquifer. The Ocala is at or near the surface in the areas represented by shading in the northwestern part of the peninsula and also in an area in western Florida adjacent to Alabama and

Jan 1, 1952

By Howard E. McKinney

A high-pressure wellhead lubricator has been developed to facilitate telemetering electrical measurements from subsurface reservoirs to the surface with the well under normal flowing conditions. The field unit in use at the present time employs a 5/16-in diameter, single-conductor armored cable and is to be used in wells with surface pressures up to 5,000 psi. It has a pressure sealing element that maintains a continuous and absolute seal around the cable as it enters or leaves the tubing at speeds up to 175 ft per minute. A cable injecting device is used which obviates sinker bars or weight sections on the instrument. INTRODUCTION The development of instruments for securing physical measurements in pressure wells has been confined in the past to those instrument which would operate on a wire line and record the necessary measurements in the downhole instrument itself, or those which would operate on an electric cable in a well with the surface pressure killed by the use of weighted fluids or by the use of tubing plugs. In one case the accuracy of the measurements is questionable, and in the other the range of application is very limited. Considerable work has been done by other interests to provide effective means to accomplish the necessary telemetering. The U. S. Bureau of Mines developed a wellhead lubricator prior to 1947 which permitted a 5/16-in diameter single-conductor cable to be lowered into a well with a surface pressure of approximately 500 psi. This unit was used successfully in a number of tests in Oklahoma. A company which tests wells has recently offered on a service basis a wellhead lubricator with a 3/16-in diameter cable that reportedly operates up to 2,500 psi surface pressures. Each of the above operates on a staging principle to effect a seal. In both of these units some leakage of well fluid occurs when the cable is moved. SPECIFICATIONS FOR DESIGN In order to provide the maximum flexibility in its use, the following parameters were established for the design of our high-pressure wellhead lubricator: L An absolute well fluid seal up to 5,000 psi surface pressures. 2. Means for raising and lowering the instrument at speeds of at least 100 ft per minute. 3. Provision for the instrument to enter and leave the well without disturbing the well flow or the reservoir conditions. 4. A cable large enough to provide suitable electrical characteristics and suitable mechanical properties. 5. A method of operation that will not damage the well in any way. The present high-pressure wellhead lubricator field unit fulfills the above requirements. DESCRIPTION OF THE UNIT AND ITS OPERATION The cable selected for this use is the standard Amergraph 1H2 as manufactured by the American Steel and Wire Co. This particular cable is normally used by the Halliburton Oil Well Cementing Co. in their conventional well logging operations. Although the cable presents a noncircular cross-section (Fig. l), its diameter is very consistent; lor example, maximum diameter is 0.325 in., minimum diameter 0.314 in. This [actor permits the use of the sealing element, as later described. Early in the development of the high-pressure wellhead lubricator it was apparent that we could not effect a direct gas seal around a moving 1H2 cable. This becomes evident when an examination of the cable cross-section is made. The voids between the strands of the outer armor provide natural channels lor the flow and escape in large quantities of a low-viscosity fluid such as gas. However, it is relatively simple to

Jan 1, 1952