Search Documents

By B. T., Colley

AS always when metallurgical operations are conducted within or close to agricultural and stock-raising regions, the question of damage due to fume and smoke presented itself when the Cerro de Pasco Copper Corporation's new smelter commenced to operate in La Oroya in 1922, For more than twenty years the Corporation had operated its old plant close to Cerro de Pasco without encountering difficulties from smoke claims, owing to the fact that it was in an open plain where more or less constant air currents carried and dissipated the smoke over large areas, affording ample dilution. But Oroya is in a deep canyon formed by four contributing valleys up and down which the smoke travels for long distances in a more or less concentrated form. Though the altitude of Oroya is more than 12,000 ft., and the surrounding country rises to much greater elevations, nevertheless there exists there a large and important stock-raising industry and also a considerable development in agriculture, consisting of the cultivation of potatoes, barley, etc.

Jan 1, 1945

By Howard C. Dunkle

Various factors can affect the quality of B1112 and B1113 steel as produced in a bessemer plant; among them: vessel-charging practice, blowing practice, ingot-pouring practice, ingot delivery-time practice, pit-heating practices, and ingot-rolling practice. Evaluation of the influence of ingot delivery time on quality has been chosen as the subject for this paper because this time is completely within the control of the operator, and on this particular factor there is a tremendous amount of information in the dusty archives of the average steel plant. In order to know how much improvement can be made and when attention should be directed to other factors that influence quality, in the continual struggle for improvement, the effect of ingot delivery time must be accurately evaluated. Once this is done, the importance of other variables can be accurately obtained, thus eliminating the necessity of resorting to opinions that are of doubtful value at best. In the study described herein, extensive use was made of the statistical card system as a method of determining the effect of ingot delivery time as a quality factor in bessemer screw-stock grades by simple direct correlation. The value of this statistical method as a means of accurately determining the influence of various factors has been amply demonstrated by Work1 for the bessemer process and by Hand and Gould2 and Fetters and Chipman3 for the open-hearth process. The quality records of 300,000 tons of bessemer screw-stock billets were used in this study of the effect of ingot delivery time on the rejections for breaks, pipe, check and seams. The reduction in the number of rejections for poor quality reduces the costs and increases the productivity per man-hour. The operator today, more than ever before, must know how to keep costs down, how to do it most quickly and in the best way, and how to obtain the highest quality in line with the ever increasing demands of the customer. It is necessary for him to know the individual relations and interrelations between various factors affecting the quality of the manufactured product if he is to produce material that will meet competitively the cost, performance, and quality demands of the trade. SIGNIFICANCE OF STEEL MANGANESE, MIXER SILICON AND STEEL SULPHUR AS QUALITY FACTORS In order to obtain the highest grade of material it is necessary to control many factors-not just one or two, as operators

Jan 1, 1945

By C. E. Sims, H. M. Banta, S. L. Hoyt

Over the past few years, metallic arc welding has been extended to steels of the hardenable type. As compared with other methods of fabrication, production has been facilitated, service performance frequently has been improved, and the overall results have been so favorable that engineers and production men have placed great emphasis on this application of welding. The metallurgist and welding engineer, however, have been confronted with new problems, since, for one reason, the harder steels are more apt to crack and special precautions must be taken if sound joints are to be procured. Some of the factors that are pertinent to this problem are metallurgical, and it is an object of this contribution to discuss steel manufacture and processing methods and to show how their control assists in reducing the hazard of cracking. By this time, the problem of cracking— specifically underbead cracking, or "hard cracks," or parent-metal cracks-—is well known, and a large amount of work has been published, both here and abroad, dealing with this subject.' The tests described are made under restraint to facilitate cracking and arc so designed that a semiquantitative, or at least a relative, value of the cracking tendency is obtained. As one would expect, it has been reported that the incidence of cracking increases with the carbon and alloy content of the steel. More specifically, the cracking tendency is said to increase with the hardenability of the steel, though it is now recognized that the situation is not so simple. The phenomenon itself, on the other hand, has been but loosely described, and it is in only broad generalizations that this cracking has been related to steel metallurgy. Thus, while it has been abundantly demonstrated that the hardenable aircraft steel, S.A.E. 4130, must tend to crack when are-welded, the problem still remains of why two lots of the same composition and the same hardenability can vary so greatly in cracking tendency, or what it is about the prior metallurgical history that so strongly affects the results. Further, while the efficacy of preheating and postheating in preventing cracking is recognized and utilized in production, the mechanism by which they function seems not to have been described. These points are thought to be significant in the production of steel for fabrication by metallic arc welding and, hence, of interest to mill and process metallurgists and welding engineers. Consequently, it is another object of this paper to discuss the mechanism of parent-metal cracking, including the influence of the condition of the steel and the control of cracking by manipulation of the time-temperature conditions during and after welding. A new method of rating the cracking tendency is also discussed, and the results of the test are related to steel composition and structure or prior history. The work to be described was the outgrowth of work in 1940-41 at Battelle Memorial Institutc on two projects, one

Jan 1, 1945

By B. M. Larsen

Attempting to review the fundamental aspects of segregation in steel ingots of all types in a paper of reasonable length, we encounter two difficulties: (I) the fact that a large number of different physical and chemical effects are involved, and (2) rather incomplete and confusing evidence on certain aspects of detail and mechanism in the freezing process in which the segregation effect is involved. The best solution seemed to be to link together most of the underlying factors into a simplified theoretical picture that appears to the writer to explain most of the observed data, in the hope that this will serve as a reasonably good target for discussion and criticism. Segregation effects, especially in steel ingots or castings, are often divided into " microscopic" and "macroscopic," depending on whether the variations in concentration of solutes or dissolved elements in the iron occur as: (I) a periodic variation over the small distances between the nuclei and the surfaces of the primary grains, or (2) as a larger scale effect involving concentration gradients over distances of the order of several inches, more or less. The reason for this somewhat artificial division is, of course, that it is only the macroscopic scale effect that has much practical importance. About the only effect of practical importance that results from microscopic segregation is the banded structure often left in rolled sections, and even this is relatively harmless in most cases. However, the causes of microscopic segregation also untlerly the larger scale effect, so we must first consider matters such as the formation and growth of crystal nuclei, selective freezing and diffusion, and others that are fundamental to all sepregation effects. Undercooling and Nuclei Formation It is probable that although the degree of undercooling is small in iron, as in metals in general, a certain amount of it takes place, and also that the number of crystal nuclei increases very rapidly with increased undercooling below the liquidus temperature. In practical terms this means that the nuclei number illcreases very rapidly with increased cooling or freezing rate, thus being dependent on the rate of heat flow out from the zone of crystallization. Temperature Gradients and Heat Dissipation during Freezing Each pound of steel evolves about 100 B.t.u. when freezing. In addition to this, the temperature gradient in the solidified portion (required to dissipate the heat as freezing progresses into the axis) necessitates a loss of heat required to cool the solid metal below its freezing range, which is equivalent to an amount of not so much less in magnitude. In a 5-ton ingot, the total would include about one million B.t.u. for freezing alone and about 0.4 to 0.5 million B.t.u. for the gradient, up to the end of the freezing period. Thus the rate of freezing depends primarily on the rate of heat dissipation. In the ordinary ingot shapes, the axial rate of growth of the solid

Jan 1, 1945

By W. D. Brown

Newell1 has shown that hydrogen is removed from steel in a vacuum at a temperature of 500° to 900° C. within 136 hr. Holm and Thompson2 also state that, especially when the hydrogen is high, the results obtained by extraction at 800°C. agree with those obtained by vacuum fusion. In this laboratory, an apparatus was designed (Oct. 1940) and used wherein the piece of steel was heated at 100°F. in a Torricellian vacuum (Fig. I). This vacuum was produced by raising and lowering a "leveling bottle or bulb" containing mercury. Extensive tests were made with this apparatus. The weakness of the procedure was the possibility of leakage of air into the tube around the rubber stopper at the bottom. The present plan is to raise and lower the mercury by applying vacuum from a mechanical pump, to the top of the tube and then to a bottle of mercury in which the bottom of the tube is immersed. The Apparatus The extraction is made in a Pyrex tube A, I in. i.d. It is drawn down at the top at N and an 8-mm. i.d. tube is welded on it. To this a Pyrex stopcock E, 4-mm. bore, is welded. The tube between N and E is preferably 8 in. long and is graduated in milliliters. The total length of A to the stopcock is 28 inches. Heat is supplied by a split-tube furnace. 0 in. long by 6 in. in diameter, hinged on the side. A short pyrometer couple P is inserted through the walls of the furnace. In use this is standardized by comparison with a standard couple in a I-in. tube, just opposite this short couple. In the I-in. tube A a glass rod R, flattened at one end, supports the sample S and the length of R is so adjusted that the sample is in proper place. (It may float in the mercury.) The tube A is inserted in a large rubber stopper to fit the bottle B and extends nearly to the bottom. It is so placed that the handle of the stopcock faces the operator. In this stopper also is a short tube D bent at right angles for the application of vacuum. Also in this stopper is an 8-mm. tube C reaching nearly to the bottom; this is bent so as to miss the heater and again bent to bring it in line with and as near as possible to the upper and reduced part of tube A. On this tube C is welded a 4-mm.-bore stopcock H. In order that the two tubes may be as near as possible, the handle of stopcock H faces the back, or is the reverse of stopcock E. The total height of II above the bottom is 28 in. As explained later, this is the pressure-measuring tube C. The bottle B is about half full of mercury. The mercury must cover the ends of A and C by about I in. when they are evacuated. By tees T and rubber tubing RT the tubes A, C and D, the latter through the three-way stopcock M, are connected to the vacuum pump. A sheet of asbestos at K prevents the stopcocks E and H from becoming so hot that they leak. A good grade of vacuum lubricant prevents leakage of E and H. In order to measure the pressure of the

Jan 1, 1945

By J. K. Stanley

It has been known for many years that the magnetic properties of a ferromagnetic material are very sensitive to internal strain. Any structure-sensitive property such as ferromagnetism, which is a function of the regularity of the atomic arrangement, and discontinuities such as grain boundaries must show deviations from an equilibrium state when the regularity of the lattice is disturbed. Experience has shown that such distortions have a marked effect on the magnetic properties of a ferromagnetic material. The purpose of this paper is to show the feasibility of using magnetic methods in detecting internal strains. More specifically, it will be shown how such properties as permeability, rema-nence, and coercive force change on cold-working of aluminum iron and how these magnetic properties change during the annealing below the recrystallization temperatures. This work was conducted for two reasons. One was the desire to see in what manner strains are relieved in aluminum iron at low temperatures—a subject of practical importance in soft magnetic materials—and the other was the feeling that a study of cold-working and strain relief might shed some light onour understandingof what takes place in the deformation of metals. Definition of Terms It is necessary to define the terminology used in this Paper because magnetic nomenclature is usually unfamiliar to the metallurgist, and certain other terms, such as recovery, have been used ambiguously by metallurgists and others. Magnetic terms are best explained by reference to the common hysteresis loop of ferromagnetic materials (Fig. I). In Fig. 1 the coordinates are magnetic induction, B, (ordinate) and magnetizing force, H. (abscissa). The c.g.s. unit for the magnetic induction is the gauss, the number of flux lines per square centimeter, and the unit for the magnetizing force is the oersted, the number of lines of force per centimeter in air or vacuum. If one starts with a completely demagnetized specimen and magnetizes it, a typical virgin magnetization curve beginning at the origin is obtained. This curve is also the locus of tips of a family of smaller hysteresis loops. From this curve it is to be noted that the induction is not proportional to the magnetizing force, and that it appears to approach a limiting induction called the saturation value, and does so for values of H of 1000 oersteds. The ratio of the magnetic induction (gauss) to the magnetizing force (oersteds) is called permeability, . Thus u= B/H and if the magnetizing force H (oersteds) is specified as ro or 100 oersteds, the permeability is written as or l00 This is the accepted notation, and will be used in this paper. The values of permeability for H = 10 or I00 are chosen as indices for 106

Jan 1, 1945

Shortly after Denny, Robson, and Irwin published their first paper in 1937, on the prevention of silicosis by metallic aluminium, experiments were begun on the practical application of the discovery.It was thought at that time that aluminium powder, to be effective in aluminium therapy, would have to be intimately admixed with siliceous dust at the latter's source. There followed several years of experimental work underground, during which the application of aluminium powder was tested in:(1) Speakers on machine columns, vibrated by drills.(2) Vials placed in drill holes to be blasted.(3) Both homogeneous and heterogeneous mixture with explosives.(4) Packages with tamping.(5) Compressed-air lines.(6) Special compressed-air ejectors for use while drilling and after blasting.(7) The discharge of ventilation fans.(8) The filters of respirators.It was concluded from this research that any adequate method of introducing aluminium powder into a mine atmosphere would require too much extra gear, supervision, and aluminium p;wder, and would interfere unduly with underground routine.Later, animal experiments by Denny, Robson, and Irwin2 showed that aluminium powder provided effective therapy when inhaled independent of silica dust. Therefore, some means of surface treatment was deemed more practical.APPARATUS USED IN THE DEVELOPMENT OF ALUMINIUM PROPHYLAXIS SAMPLINGA basic requirement was a method of sampling to assess accurately the particle-size concentrations of dispersed aluminium powder. Konimetry, though regularly practised at McIrityre, was inadequate for the research in mind. On the other hand, the efficiency of the thermal precipitator was recognized as being very high. Accordingly, the latter instrument was chosen as best suited to our needs. Through the courtesy of the Ontario...

Jan 1, 1945

By S. G., Lasky

IT seems to be in the nature of concepts that they have many meanings, and that the meaning best reflecting the primary interests of a person tends to be accepted by him as the normal meaning of the concept. The concept of ore reserves is no exception, for there is no unanimity of meaning among the several groups of us who are interested in ore reserves, nor even among the individuals of a single group. The groups most interested in ore reserves would seem to include at least the mining industry, perhaps State taxing agencies, and the Federal Government in all its diversified activities, and I would include also the citizenry at large or at least that part of it that consciously thinks about problems-of national welfare. To each of these, and to different individuals within them, the term reserves represents something different, and the farther away the individual or group gets from physical contact with the ore, the more abstract does his or its concept become. It is something different to the policy maker from what it is to the fact-finder or to the miner.

Jan 1, 1945

By George H. Found

During recent years considerable interest has been focused on the energy-absorption characteristics of metal when it is cyclically stressed in vibration. The most familiar manifestation of this phenomenon, which is called the "damping capacity" or "internal friction" 06 a material, is involved in the dissipation of mechanical energy of vibration, which otherwise would build up to stress levels where the problems of noise and fatigue are involved. In addition to its engineering importance in structures, the damping behavior of metals, particularly at low stress amplitudes, has also been used as a unique metallurgical research tool with which to provide sensitive means for indicating certain structural changes within metals. Important contributions toward understanding the energy-dissipating -mecha-nisms that are responsible for internal friction in metals have been made in the last few years. The information is not yet sufficiently extensive, however, to provide a useful metallurgical concept describing exactly how the structure affects the internal friction, or to encourage more general use of this technique among metallurgists. Three fundamental mechanisms have been proposed, as a result of recent experi- mental investigations, to account for the internal friction in nonferrous metals in low-stress amplitude tests. These include damping due to internal thermal currents that are created and flow in metal because of differential vibratory stress effects,' damping due to localized inelastic stress relaxation at inhomogeneities within the meta1,2,3 and damping related to plastic flow of a localized type for which an explanation has been sought in terms of the dislocation theory.' How each of these mechanisms functions as a result of structural changes in the metal is, in general, not well understood because of insufficient experimental data for which the controlling variables ham been segregated and because of uncertainties in regard to the nature of the structural changes themselves. In several investigations the effects of cold-working on the internal friction of polycrystalline brass and aluminum have been described. As reported by Köster and Rosenthal,5 and by Förster and Breitfield,6 there is an initial large increase in the damping when the metal is worked. The initial high value is not stable, but declines rapidly, at first, in a hyperbolic manner. About Ioo hr. after straining, a stable value is reached of magnitude proportional to the amount of strain.' In Fig. I is shown the relationship found by Zener and his collaborators between the internal friction due to cold-working of alpha brass and the amount of cold-working.8 Several investigators have made internal-friction measurements on worked poly-

Jan 1, 1945

By T. S. Washburn

Deoxidation is one of the most complex metallurgical operations in the basic open-hearth process. The necessity for deoxidation arises from the fact that the refining operations that precede it require the oxidation of the steel bath. when the refining is completed and the desired composition of the bath has been obtained with respect to the elements subject to control by 'oxidation. there is usually an excess of oxygen present in the bath from the standpoint of the amount desired in the finished steel. The objectives of deoxidation are to control the amount and type of oxides and, although not directly ilnp1it.d by the term or always considered as a Part of the process, to control the amounts of gases such as hydrogen or nitrogen that will be present in the finished steel. There are other aspects to be consideretl in connection with deoxidizing procedures. In addition to the primary objectives of oxide and gas control. the composition of the steel is affected by the elements introduced during the deoxidizing process. Factors in furnace operations are likewise involved, such as slag composition, temperature control. arid heat time. .ill of these should be considered in establishing the most satisfactory deoxidizing procedure for each grade of steel. The purpose of this paper is to outline the objectives of deoxidation as related to steel characteristics, and to summarize the factors in furnace practice and the economic aspects to be considered in connection with deoxidation procedures. Objectives of Deoxidation The primary objectives of deoxidation are the formation and elimination of oxides. The amount of oxygen present in the bath prior to deoxidation is an important factor, since it is the basis of any deoxidation procedure. The oxygen content of the bath is primarily a function of the carbon content, although it is affected also by the temperature, the oxidation of the slag, and transient conditions within the furnace. The relation of oxygen to carbon in the bath is shown in Table I. Table I shows that under actual operating conditions, the amount of oxygen present in the bath is higher than the theoretical amount. This relation would be expected, since the bath is in a state of metastablc equilibrium during the period that the carbon is being eliminated. The most important feature demonstrated by this table, however, is the rapid increase

Jan 1, 1945

By J. O. Mack, J. B. Russell

In recent years, solders containing 20 per cent tin with no bismuth or cadmium have been developed by a few companies, and personnel have been properly instructed in their use. In addition, since the tin shortage, a number of solders containing less than 10 per cent Sn, and some with no tin, are being used in special applications; however, a solder of this type has yet to be developed that is satisfactory for general use. Table i.—Composition Ranges Prescribed for a Commercial Substitute Solder Element Per Cent Tin............................ 18.0-20.0 Bismuth (maximum)a............ 0. 80 Silver.......................... O. 10-1. 25 Bismuth plus silver (minimum).... 0. 85 Antimony (maximum)............ o. 50 copper (maximum),,,,,,,,..,,,, 0. I3 Other elements, each (maximum)6 0.03 Lead........................... balance a When silver is present in excess of I per cent, the Bi content shall be 0.50 per cent or over. b Total not to exceed 0.10 per cent. The Purpose of this investigation was to develop an alloy containing a maximum of 15 per cent tin, with no cadmium or bismuth, having solder properties equivalent to or better than those of substitute solders now specified containing 18 to 20 per cent tin (Table I), or even approaching the properties of the standard 40 to 60 tin-lead solder. The wartime restriction of bismuth and cadmium, elements that have beneficial effects on fluidity, solidification range and strength, makes it increasingly difficult to develop a general-purpose solder containing a maximum of 15 per cent tin. In the course of this investigation, 11 elements were used in various combinations with the basic I5-85 tin-lead alloy. These elements were antimony, silver, copper, indium, thallium, lithium, calcium, barium, potassium, sodium and arsenic. In all, 116 low-tin solders were investigated, with the idea of developing a solder that will give satisfactory working properties, specifically in regard to "wetting" of copper, brass and iron, solidification range, capillarity and shear strength of a soldered joint. The relative importance of these various properties plays an important role in the search for substitute solders, since it is almost impossible to retain all of the desired qualities of a high-tin solder and still make drastic changes in the alloy composition. Because of the expected uses of a general-purpose solder, it is necessary that it have properties, especially in regard to wet-tability, that will enable it to be used on the metals in common use. Basic Considerations The maximum liquidus temperature of a solder is determined by the particular application involved and the temperature that can be obtained by the source of heat. If a soldering iron is used, it must not only

Jan 1, 1945

By G. R. Gohn, S. M. Arnold

The results of stress-corrosion tests upon several non-ferrous sheet metals are presented in this paper. The metals include tough pitch copper, five binary brasses, two leaded brasses, one copper-silicon alloy, two tin bronzes, and two nickel-silver alloys. The tests indicate that for most of these sheet metals, externally applied bending stresses below the yield point (0.01 per cent offset) do not result in stress-corrosion cracking as determined by the A.S.T.M. Tentative Method of Mercurous Nitrate Test for Copper and Copper Alloys (B 154-41T).~ Only in the cases of low brass, high brass and medium leaded brass, all cold-worked 4 B & S numbers hard, was any corrosion cracking observed below the yield strength, and in all cases such failures occurred at stresses above the proportional limit for these materials. However, when some of the same materials which showed no evidence of stress-corrosion cracking at stresses below the yield strength, are stressed beyond the yield point, stress- corrosion cracking is quite apt to occur. Since experience has shown that some of these materials, particularly the brasses, are susceptible to stress-corrosion cracking under service conditions, these tests would indicate that, besides externally applied stress and corrosion, plastic deformation in addition to that resulting from the original cold working of the material is also required to produce conditions conducive to stress- corrosion cracking.

Jan 1, 1945

By B. M. Larsen, K. Heindlhofer

Jan 1, 1945

By W. W. Adams

The first full year of the second World War for the United States presented a picture of the metal-and nonmetal-mining 4 industry which, without proper analysis and explanation, would convey a distorted view of achievements during 1942, especially because employment at gold and silver (lode and placer) mines-the largest group-declined to such an extent that the over-all totals for the country were reduced even though increases were made at mines producing copper, lead-zinc, iron, miscellaneous metals, and non-metals. A complete panorama of the metal-and nonmetal-mining industry, exclusive of coal mining, reveals a decrease in the number of men employed, the man-hours of employment, and the accident-frequency rates. Were the gold and silver (lode and placer) mines to be considered as a separate category; it would be seen that the number of men employed at all the other groups of mines increased appreciably over 1941. These other increases must be considered important, since these mines produced the vital war minerals that made valuable contributions to the military successes of the United States and its Allies during the year. A separate analysis of each of the various groups of mines may be found elsewhere in this bulletin. For the purpose of maintaining continuity in this series of bulletins, however, the discussion in this introduction will be confined to the entire metal-and nonmetal-mining industry (excluding coal mining, for which a separate bulletin, No. 462, has been published).

Jan 1, 1945

By A. C. Fieldner

The past full year of war has increased greatly the demand for virtually all kinds of fuel, and the Bureau of Mines research and service facilities have been extended to meet these unprecedented requirements. Liquid fuels, such as aviation and motor gasolines, are fundamental to modern warfare. Bituminous coal and anthracite are needed, not only to servo the expanded industrial program for which coal normally is used but also to replace natural gas, wherever possible, and fuel oil in the Eastern States, New England, and the Pacific Northwest. Railroad transportation with energy derived from coal is replacing much of the motor-vehicle transportation that has been stopped or curtailed to conserve rubber. Pulverized coal hoe been sound to be a satisfactory and cheaper substitute for fuel oil in metallurgical heating furnaces. Celloidal fuel - a mixture of coal dust and oil - may offer a partial substitution for curtain coal-burning equipment. Several industrial experiments have been made with this type of fuel. The expansion of the steel industry in connection with the war program has required a corresponding increase in the production of metallurgical coke and its associated byproducts - light oil, tar, ammonium sulfate, and surplus gas. If the war is of long duration and new reserves of petroleum are not discovered, wartime trends from fuel oil to coal probably will not be reversed.

Jan 1, 1945

By Sidney H. Haughton

WHEN the white pioneers of the eighteenth and nineteenth centuries advanced from the coastal settlements of southern Africa into the interior of the subcontinent, they found it inhabited, more or less sparsely, by brown or black peoples mainly of pastoral habits but equipped with a fighting spirit and certain fighting weapons. Some of the tribes were smiths, others were miners and metallurgists; all used fuel, either industrially or domestically. Some of that fuel was wood, some cattle dung, and in some places the natives mined outcrop coal. Coal was first discovered by Europeans in Natal about 1840. After proper deliberation and after allowing due time for a consideration of all the implications, the Natal Government decided in 1881 (40 years after) to import an English expert to investigate and report on the discovery. Things then moved rapidly, and in what to a geologist is the remarkably short space of eight years, Natal collieries were producing at the rate of nearly 30,000 long tons per annum or 100 long tons per working day!

Jan 1, 1945

By R. S. Dean

REQUIREMENTS for war materials have led to large scale experimentation upon metallurgical innovations. It is of interest to inquire what this may contribute of permanent value to our existing technology, as innovations adopted during war are apt to be discarded promptly at its end. This is because utilization of substandard ores usually requires a new technology for ore treatment, and a new use-pattern for employment of the products. Thus two very different problems are involved: first, devising a process; then, adopting its products by industry, with readjustments of the use-pattern if necessary. A new process may be as good or better than an old one, but the readjustments required for use of its products may prevent its general adoption if this implies scrapping existing plants and investing much additional capital. Metallurgical innovations are of three kinds: I. The use of substandard material in processes already established; 2. The grading-up of substandard material to render it more suitable for established processes; 3. The adjustment of technology and use-pattern to the raw materials that we have.

Jan 1, 1945

By George H. Hanna

THE importance of the Donets coal field (the Donbas) to the national economy of the Soviet Union is well known. Great as was the significance of this tremendous deposit of coal in prewar days it is destined to become an even greater factor in the economic life of the country now that the tremendous havoc wrought by the Germans is being remedied. Since the war began, new coal fields have been extended; for example output of the Moscow and Karaganda (Kazakhstan) fields has become considerably larger while new mines are producing coal in several parts of Uzbekistan and Kirghizia. The huge West Siberian coal field, the Kuznetsk Basin, is producing more coal than ever before to supply the industries of that region and of the Urals. But so great has been the development of industry to meet war needs, especially in those districts of the Soviet Union that lie to the East of the Urals, that the coal obtained, eked out by such locally-won fuels as peat and wood, is still barely sufficient to meet industrial requirements. The main burden of the coal supply for the restored industries of the West, therefore, will fall on the Donbas.

Jan 1, 1945

By J. A. Retty

HOLLINGER CONSOLIDATED GOLD MINES LTD., through two subsidiary companies, has the exclusive right to prospect in two contiguous areas in central Labrador. This paper presents the results of the mineral exploration that has been conducted in these areas to date. One of the subsidiaries of Hollinger. the Labrador Mining and Exploration Co. Ltd., under an agreement with the Newfoundland Commission of Government, holds an area of approximately 20,000 sq.mi., which comprises the western portion of Newfoundland-Labrador and includes the upper basins of the Hamilton and Naskaupi Rivers. (The main area of the deposits so far discovered may be located on a map at about 67° west longitude and 55° north latitude.) The other subsidiary of Hollinger, Hollinger North Shore Exploration Co. Ltd., has licensed from the Province of Quebec an area of approximately 3900 sq.mi. lying directly north of the Newfoundland-controlled area at the headwaters of the George, Whale, and Swampy Bay Rivers. The M. A. Hanna Co., large iron-ore operators of the Lake Superior region, are participating in the project. With the exception of the years 1940 and 1941, field work has been conducted in the Newfoundland area since 1936, and in the Quebec area since 1939. Hollinger assumed the management in 1942. The field base is at Hollinger Lake, some 300 miles north of the tidewater base at Seven Islands, Quebec, which, in turn, is just west of the mouth of the Moisie River, on the Gulf of St. Lawrence. Air transportation is used exclusively to service the operation.

Jan 1, 1945

By Francis M. Walters

IN spite of the war and the preoccupation of many physical metallurgists with work on secret or confidential problems, definite progress was made during 1944 in our understanding of the behavior of steel and of the effect of alloying elements. During the first two years of the war there was much concern over the possible unavailability of certain alloying elements; this period saw the development of the N.E. (National Emergency) steels. However, the measures taken eased the alloy situation and currently, highly practical problems under study are the graphitization of low-carbon steel and weld-cracking, while investigations of more theoretical interest have concerned hardenability, isothermal reactions, the effect of hydrogen and the interpretation of the notched-bar impact test.

Jan 1, 1945