Search Documents

By R. B. Corbett

"INTRODUCTION Aluminum and manganese bronzes as a group, may be separated readily from other copper-base alloys by experienced sorters. However, separation of aluminum bronze from manganese bronze is generally a matter of guesswork, so that accurate separation presents a difficult salvage problem.Attempts at separation by the thermoelectric tester. 3/ which had proved successful in solving other sorting problems, showed in this instance that the desired separation was uncertain because of the wide range of composition allowable in each kind of bronze. If only one composition of each kind of bronze were used in industry, separation by the thermoelectric method probably would be simple. However; the variability in composition observed in commercial alloys is so great that the thermoelectric power of the one type frequently overlaps the range of values found for the other. As a result, specimens frequently are classified in the' wrong group.Separation of the two types of bronzes on the basis of measurements of magnetic properties on filings from the various samples also proved unsuccessful because the test results overlapped to such an extent that no clear-cut division could be obtained.Electrode potential measurements were made also on the aluminum and manganese bronzes in the hope of distinguishing between them. A drop of saturated potassium chloride solution was placed on the fresh surface of the metal and the tip of a calomel electrode introduced therein. The voltage generated was measured by connecting the electrode and the bronze part to a research-type potentiometer. Although the voltages generated by the manganese bronze parts were greater than those generated by the aluminum parts, the difference in the closest two sets of readings was not sufficient to warrant a good separation. When a concentrated potassium alum solution was used instead of the potassium chloride solution, a wider divergence of voltage was produced by the various bronzes, but unfortunately readings overlapped in several instances."

Nov 1, 1944

By Wilbert J. Huff, Raymond H. Moore

"Black powder is employed widely in peace and war. Its properties are therefore of considerable interest to many. The Bureau of Mines frequently is asked to furnish information on its use and safe handling in the mining and mineral industries in times of peace and is now engaged in studies of its application to the arts of war.Black powder has been the agent in many accidents - some very disastrous - and its handling and use are deemed very hazardous. The belief is widespread that the hazards are due principally to the ease with which the powder is ignited by a hot spark or flame in contradistinction to high explosives; these usually are ignited only with difficulty, and some burn incompl0tely and to a certain extent are self-extinguishing. Primary precautions, .therefore, should be taken to prevent the access of heat, spark, and flame.In black powder manufacturing operations a frequent source of disaster is the initiation of fires and explosions in the wheel mills in which the sulfur, charcoal, and nitrate are incorporated. Long experience has indicated that the wheel mill probably will fire if the powder is not kept moist enough; manufacturing supervision calls for the maintenance of a minimum moisture content, at least during the milling. Accidents occur elsewhere in the manufacturing line, and in an endeavor to minimize these, particularly those happening in corning mills, one of the writers suggested many years ago that a suitable humidity be maintained in other operations in the hope that it would serve protectively as in the wheel mill. The experience of one company for many years with this practice was favorable. It seemed desirable therefore, to explore the question experimentally."

Nov 1, 1944

By Thomas Jenning, C. M. Keithly

"INTRODUCTION This report is one of a series. 4. 5. 6/ concerned with presenting historical development, and operating data on secondary-recovery projects in various States to stimulate interest in sound secondary-recovery programs. Preceding reports in this series have dealt exclusively with descriptions of and results obtained by water flooding in three states, but no recent publication of comparable purpose describes gas-injection 7/ practices. The authors intend to present material relevant to the development and operation of gas-injection projects in Illinois, with particular emphasis on those producing from oil-bearing horizons that had been depleted to a point near the economic limit of operation by past oil-recovery methods.Most operators realize that the energy expended on the movement of fluids through gas-expansion- or gas-cap-type oil reservoirs to producing wells must be supplemented to attain maximum recovery of the oil present. Under favorable conditions, many operators choose to maintain oil-propulsive forces at or near their original magnitude by injecting extraneous fluids into a reservoir or recycling produced fluids early in the life of a field. More common, and less desirable, is the practice of replenishing these forces after primary producing methods become unprofitable. The lattes practice has been adopted in many stripper fields in Illinois and most of the oil-producing States during the last 40 years, but other old oil fields, and oil properties within those fields which were partly exploited by secondary--recovery methods, also may offer favorable opportunity for further development. To encourage and, aid operators in the development of gas-injection projects in the old oil fields of the United States, four projects have been described in detail in this report."

Nov 1, 1944

By M. A. Schellhardt, E. J. Dewees, R. Vincent Smith

"INTRODUCTION Abnormal material requirements of the nation at war impose an intensive demand upon many irreplaceable natural resources. Natural-3as reserves) for example, are being subjected at the present time to extensive depletion by large-scale withdrawals of gas to supply unprecedented demands for fuel and raw materials for the synthesis of strategic products. Fluids produced from many so-called gas-condensate type reservoirs have become an important source of hydrocarbons vital to the war effort.Development of gas-condensate type reservoirs in Arkansas, Louisiana, and Texas in recent years created many problems not common to ordinary gas-producing operations. Early in the development of condensate-type gas fields, general practices were evolved and applied to insure efficient re¬covery of the hydrocarbons existing in the gas phase under initial reservoir pressures and temperatures, put often the practices were predicted mainlyregardingupon generalized theory regarding the behavior of the fluids and were not always the most efficient, because field and laboratory procedure for testing these hydrocarbons had not progressed as rapidly or as far as field development. Specific information regarding the composition and properties of fluids ultimately recoverable from many gas-condensate reservoirs, especially, is lacking."

Oct 1, 1944

By C. W. Elder

"INTRODUCTION This report describes a method of horizontal drilling in an oil-producing formation underlying a 400-acre, approximately square plot of land in the Franklin Heavy oil field in Sugar Creek Township, Venango County, Pa. The method, which was developed on two previous projects in Ohio, 3/ consists of sinking a shaft to the bottom of a shallow oil sand and drilling holes in a general horizontal plane outward from the chamber in a pattern similar to that of the spokes of a wheel. The project was undertaken by the Venango Development Corporation in an attempt to find an efficient method of recovering oil from partly depleted sand formations.The Venango Development Corporation is composed of the following oil-producing and oil-refining companies and individuals: South Penn Oil Co., Forest Oil Corporation, Kendall Refining Co., Minard Run Oil Co., Quaker State Oil Refining Co., The Pennzoil Co., Alliance Oil Corpo¬ration, United Refining Co., Franklin Creek Refining Corporation, Canfield Oil Co., Pennsylvania Refining Co., Page Oil Co., Freedom Oil Co., D. W. and D. S. Grant, and J. P. Herrick, C. M. Davison and N. V. V. Franchot. Engineering features of the project were supervised by a committee off three engineers A. J. Saxe, chairman, W. M. Shoemaker, and C. N. Pfohl, who supervised the excavation of the shaft and the drilling of the first two holes by alternately spending a week at a. time at the project. The drilling method was under patent license from Leo Ranney, who served as technical advisor to the Venango Development Corporation; in addition, he furnished the design for the shaft and work chamber."

Sep 1, 1944

By Louis H. Berkelhamer

"INTRODUCTION In the present war, with increasing demands on foundrymen for speedy production of sound castings, the role of sand in foundries has paramount importance.Foundry sands include both molding sands and core sands. Molding sands are those used in making molds, whereas core sands include those used for ""cores"" that fill the parts of the mold intended to be openings or hollow spaces in the casting. Core sands are, as a general rule, relatively coarse-grained as compared to molding sands. Coarse-grained sands, however, are required in making molds for large castings.Owing to the intimate relationship between properties of the sand and casting defects, it is necessary (for most efficient foundry work) to keep a close check on the molding sands used and to properly select and prepare a sand for a specific job. A mold is essentially an unfired refractory composed to meet specific requirements as to strength, permeability, and resiliency. Good green strength is important in preparing and handling the mold. Low dry and hot strengths contribute to cutting and washing, whereas high strengths cause difficult shake-out, with subsequent loss of sand. When molten metal is poured into the mold: a dried skin is attained, and gases from moisture and combustibles are driven off. Excessive moisture necessary for the proper working of a sand, as well as poor venting due to low permeability, are factors responsible for producing such defects as blows and pinholing. The skin of the mold, upon contact with molten metal, first expands and later contracts; these conditions are favorable for producing scab defects. Contact with the molten metal sometimes causes the skin of the mold to sinter or fuse and may produce a sand burn on the casting. Then again, the mold may develop excessive hot strength rapidly, thereby causing a cracked casting. Experienced foundrymen can other such relationships, too numerous to be included here."

Sep 1, 1944

By Sam S. Taylor

"INTRODUCTION This report deals with a comparatively simple application of some of the engineering principles involved in the evaluation, installation, and operation of air- or gas-injection projects and well-clean-out and repair methods to increase the producing rates of oil wells in partly depleted pools during the war. The methods suggested for developing gas-injection projects take into consideration that in general no new wells will be drilled because of wartime restrictions of equipment and manpower and that only existing wells and second-hand machinery will be used. Because air will be employed as the injection medium in secondary-recovery operations where natural gas is scarce and expensive, the disadvantages and hazards accompanying, its use are discussed. Engineering techniques recognized as best modern practice are discussed in relation to the effect of simple air-injection development of properties on postwar operations and Probable ultimate recovery of oil. The report is an introduction to where, when, why, and how an air-injection project should be installed and operated; it is not intended to be an engineering manual for technical guidance in the selection, development, and operation of simulative methods of oil recovery.The report is intended mainly for these thousands of operators in the Appalachian region owning a few wells prodding small quantities or oil daily. Many such operators are anxious to increase their production rates by simulative means and to rehabilitate their wells so that they will produce more oil to help win the war but, in general, are unfamiliar with secondary-recovery operations and cannot afford to hire technical assistance."

Sep 1, 1944

By Frank D. Lamb, Lloyg H. Baning

"The crushed-stone industry has long been troubled with the problem of producing a more or less cubical product for use as concrete aggregate. Its seriousness varies widely for each producer, depending upon the character of the rock employed for raw material and the ultimate use of the crushed stone. For many construction uses, such as the macadam or bituminous-concrete- type road, flat pieces are not objectionable and may even be preferable to more cubical rock. However, most specifications for concrete require that the stone must be reasonably free from flat and elongated pieces.The rigid specifications set by many contractors have resulted in the rejection of coarse aggregate that, except for the presence of an excessive amount of flat and elongated pieces, would be entirely acceptable. In many instances, if an efficient, economical method of removing flat and elongated pieces were available, local producers could meet the requirements of the contractor and thus eliminate the necessity for importing more cubical material.A brief investigation of the problem of removal of flat and elongated pieces from crushed aggregate, carried out at the Eastern Experiment Station of the Bureau of Mines, indicated that it is mechanically possible to remove flat pieces from crushed rock.TEST EQUIPMENTA number of mechanical devices are used by the coal industry for separating slate from coal; these depend upon the difference in shape of the crushed slate as compared with the coal. Such devices as shutter screens, spiral separators, and the Norman picker would be suitable for removing flat pieces from crushed rock in the same manner as they are used by the coal industry. None of these devices was immediately available for testing purposes, so an attempt was made to construct a simple device that could be used in commercial operations."

Sep 1, 1944

By K. K. Kelley

"INTRODUCTION The Bureau of Mines nitrogen peroxide process (2) 3/ for extracting manganese from low-grade ores is essentially a two-stage process involving the reversible reactionMnO2 + 2NO2 + 6H2O = Mn (NO3)2 . 6H2O (1).At lower temperatures this reaction proceeds to the rigth and affords a means of dissolving manganece and separating it from unreacted ore. At higher temperatures the reaction proceeds to the left and manganese dioxide is recovered and nitrogen peroxide regenerated for recycling. Evidently, therefore, the energy required for decomposition of manganous nitrate is a matter of practical importance. Similar information for certain other nitrates also is desirable beceuse the nitration step of the process produces appreciable amounts of nitrates of other metals, such as iron, aluminum, magnesium, calcium, and barium, some of which are not broken down in the evaporation and decomposition steps. Thus, a portion of the nitrogen peroxide is not directly available for recycling. Whether or not it is feasible to recover nitrogen peroxide locked in the more-stable nitrates depends partly on the energy required and the conditions necessary for their decomposition.To supply information bearing directly on these subjects, several researches were undertaken at the Pacific Experiment Station: (a) Heats of formation (24, 25, 26) of nitrates of manganese, magnesium, calcium, barium, and aluminum were measured at 298.2° K:; (b) low-temperature specific heats (23), in the range 51° to 298.2° K,, and entropies of nitrates of magnesium, calcium, barium, and aluminumm were determined; and (c) heat contents (21) above 298.2° K. of the nitrates of manganese, magnesium, calcium., and barium were measured. The results of these studies, when correlated by thermodymamic methods, permit evaluation, at any temperature of interest, of the energies required to decomposethe nitrates and furnish information concerning the equilibrium pressure temperature relationships."

Sep 1, 1944

By Carlton E. Brown

In 1935 , Brown and Yant / described a microprojector ( microscopic arrangement for projecting images on a screen ) for use in counting and measuring the size of dust particles in Owens - jet dust - counter and simila dry samples of dust collected from the air . In 1938 Brown and others , described a modification of this microprojector that could be used also in counting dust in impinger samples . Microprojectors of this second type have been set up by many mining companies and others and have been made commercially available . Hamly and Pullen5/ described a modification of this microprojector for use in making rapid comparative estimates on konimeter samples and other determinations . This report contains information on still another modification named the "midget microprojector " because of its small size .

Sep 1, 1944

By D. B. Taliaferro, Thomas Jennings, C. M. Keithly

"INTRODUCTION This report describes the methods of development and operation and gives the results of controlled water injection into oil sands in Illinois. It is the third of a group relating to water-flooding operations in various States; previous reports have covered projects in Oklahome 5/ and Kansas.6/ Systmatic water flooding has been in progress, in these States, for more 10 years. In Illinois the Tide Water Associated Oil Co. has been injesting water into one or two wells on each of five leases in the Robinson Acknowledgments This study was made under the general supervision of R. A. Cattell, chief engineer, and H. C. Fowler, assistant chief engineer, Petroleum and Natural Gas Division, Bureau of Mines, Washington, D. C., and N. A. C. Smith, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.The cooperation of the operators who are conducting water-flooding projects and who have made this report possible by furnishing data on their operations is gratefully acknowledged. The writers are grateful also to the following members of the Bureau of Mines for assistance in preparation and criticism of the manuscript: C. J. Wilhelm, Franklin, Pa.; and Gustav Wade, R. E. Heithecker, and Peter Grandone, Bartlesville, Okla. The illustrations were prepared by Helen Cramer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla."

Aug 1, 1944

By J. A. Woolf, A. P. Towne

"INTRODUCTION A considerable part of the metallurgical work of the Precious Metals Section comprises ore-testing experiments on ores selected as representative of various mining districts on areas. Projects authorized by the Bureau and assigned to the Precious Metals Section generally include only those ores or tailings in which the precious metals are the main valuable constituents; however, there are also included ores that contain strategic or critical metals in addition to the precious metals. The recovery of strategic and critical minerals is the most important phase of the treatment of this latter class of ores. However, if a considerable percentage of the precious-metal content of such ores can be recovered without complicating the flow sheet too much, it may be possible to treat an ore for the recovery of strategic or critical metals that could not otherwise be treated at a profit.Standard testing procedure involving cyanidation, amalgamation, gravity concentration, and flotation, or a combination of these methods, is employed in the greater part of this work. However, as the complexity of the ores furnished for this work has increased, it has been necessary to include special applications of standard procedures in many instances, Standard methods of conducting tests and the purposes of the work as a whole have been discussed in previous reports 4/ of ore-testing studies. In the present report, whenever it has been necessary to apply some special phase of standard treatment, this has boon explained in detail in that particular section of the report."

Aug 1, 1944

By M. A. Schellhardt

"INTRODUCTION The augmented demands for natural gas in many parts of the United States as a result of war have increased the need for information regarding the producing characteristics of natural-gas and gas-condensate-type wells capable of delivering large volumes of gas, as such information is important to the formulation of conservative and efficient operative and recovery practices.,For many years, the capacity of natural-gas wells to produce gas has received studied consideration by Bureau of Mines' engineers, and three reports 3/ on gaging gas-well capacities have been published. In Report of Investigations 2929, Pierce and Rawlins point out that for accurate gaging, the actual pressures at the face of the sand in the well and the relationship between such pressures and the rates of flow of gas through the sand must be determined. Their report describes a method of attacking the problem of determining the actual pressures at the sand by means of observations of pressures and volumes at the wellhead.In Report of Investigations 2930, Pierce and Rawlins explain how the fundamental relation"

Aug 1, 1944

By C. J. Cohen, L. A. Dahners

"SUMMARYA method has been developed for surveying, drill holes without lowering into the hole any surveying equipment other than an etch tube. The orientation of the rods at the collar of the hole is maintained as the etch tube is lowered. The attitude of the etch ellipse in depth with respect to the rod orientation at the collar can then be observed. This relationship permits the bearing of the hole in depth to he calculated. The rod orientation is maintained during the lowering by means of a pair of alinement clamps. One clamp is fastened to the top of each rod as the rod is coupled and is removed when the alinement has been transferred to the other clamp at the top of the next succeeding rod. A particular advantage of this survey technique is that surveys can be readily made in magnetic country rock.PRINCIPLE OF THE TECHNIQUEAn axial lamina of the column of drill roes is the lamina in which one fiber would be the centerline of the rods. In the new survey technique, the rods are fed into the hole in such a manner that the axial lamina of each successive rod maintains its position at the collar of the hole. In depth, as the rods bend in following the drill hole, the axial laminae also bend. The lamina that was originally vertical will, in general, be tilted away from the vertical. The trace of this lamina is marked on the glass etch tube before the tube is lowered in the hole. The axial lamina that becomes vertical at the survey station is recognized as that axial lamina which contains the long axis of the etch ellipse. The angle between the lamina originally vertical and the lamina vertical at the survey station is thus measurable. When the vertical axial lamina at one survey station has been determined by the etch ellipse at that station, angle R between this lamina and the vertical axial lamina at the next survey station becomes measurable also. By moans of angle R, and dip angles D1 and D2 at the two stations, the change in bearing (z) of the drill hole between the two stations can be calculated."

Aug 1, 1944

By W. W. Adams, T. D. Lawrence

"Despite the manpower shortage and other difficulties of operation in war time, the National Safety Competition of 1943 for the promotion of safety in the mineral industries of the United States was notable for having a larger enrollment of mines and quarries than in any other year except 1941 and 1942 since the yearly safety contests were inaugurated in 1925. The competition was also notable for having a larger number of man-hours represented by the competing companies than in any previous contest except that of 1942. The ratio of accidents and days of disability resulting from accidents to the number of man-hours of work performed was more favorable than in 1942; the accident-frequency rate was lower and therefore better than in 13 of the 19 years during which the annual safety competitions have been conducted, and the accident-severity rate was better than in 16 of the 19 years.The National Safety Competition is a yearly safety contest conducted by the Bureau of Mines, United States Department of the Interior. Companies that win first place in their respective group in the contest are awarded a bronze trophy, ""The Sentinels of Safety,"" which is provided by THE EXPLOSIVES ENGINEER magazine. Competing companies are segregated into six groups: Underground bituminous-coal mines, underground anthracite mines (in Pennsylvania), underground metal mines, underground nonmetallic-mineral mines, open-cut mines (without regard to kind of mineral produced), and open quarries (without regard to kind of stone produced). The bronze trophies are retained by the six winning companies for 1 year and are then transferred to the winners of the succeeding year's contest. On the pedestal of each trophy is engraved the names of the winners of the trophy. With the award of the trophies for 1943, therefore, the pedestal of each trophy bears the names of 19 winners."

Aug 1, 1944

By Louis H. Berkelhamer

"INTRODUCTION ""Free silica"" includes all free forms of silicon dioxide, such as quartz, chalcedony, tridymite, cristbbalite, opal, diatomaceous earth, and lechatelierite. The term, has been used rather loosely however, as synonymous with quartz, as quartz is the most abundant form of free silica. ""Combined silica,"" on the other hand, has been reserved to denote silica combined with other elements as silicates.Improvements in methods for the determination of free silica, and quartz in particular, have been the subject of considerable interest during the past decade, owing mainly to the accented and increased knowledge concerning quartz as a causative factor in silicosis. Analysis for quartz, however, is of importance in many other fields, including the determination of quartz in ceramic raw materials, such as feldspar and clay; the evaluation of a beneficiation procedure by the ore dresser, such as in the concentration of iron ore; control studies of a manufactured product, such as silica brick; and routine analysis of rock, mineral, and ore samples by chemists and petrographers."

Jul 1, 1944

By Will H. Coghill, G. Dale Cole

"INTRODUCTION This paper describes a method for the rational sorting of particles by means of a laboratory batch jig. Its purpose is to show that a material can be reliably appraised for gravity concentration without the drudgery of sink-float fractionations.Development of the batch- jig method of testing was incidental to a study of the Birmingham, Ala., red-iron ores now being conducted by the Bureau of Mines in cooperation with the University of Alabama and the ore-producing companies.APPLICATIONOres and coal are commonly tested for their gravity-concentration characteristics by specific-gravity dissections in heavy liquids. The heavy liquid most commonly used for coal is zinc chloride and for ores they are benzene, carbon tetrachloride, acetylene tetrabromide, methylene iodide, and thallium malonate formate. The last is poisonous and corrosive to the skin but is essential for separations in the 3.3 to 4.4 specific gravity range. The last two of these liquids are expensive, and several of them are hard to obtain now.Although it is not suggested that heavy-liquid dissections be eliminated entirely, sometimes a more reliable evaluation of coal and ore can be obtained by other and more simple means. For example, sink-float data were unsatisfactory as a guide to commercial gravity concentration of a red-iron ore because they did not take into account the difference in particle shape of the hematite and gangue and the differences in true and apparent specific gravity of the hematite grains, some of which were porous. For this ore, the batch-jig method of testing herein discussed proved advantageous. Not Only did the batch-jig data give a truer picture of the concentration problem, but only about one-tenth the time of the conventional sink-float tests was required."

Jul 1, 1944

By Peter Grandone

"INTRODUCTION The injection of water into partly depleted-oil-bearing formations as a means of supplying additional energy to flow oil wells now is recognized by the petroleum industry as an effective method of increasing the recovery of oil. The benefits to be derived from water-flooding oil sands were discovered accidentally more than 4o years ago, when oil producers in the Pennsylvania and western New York fields observed suustantial increases, in oil-production rates when water leaked past corroded casings of old wells into producing sands. This observation prompted some operators purposely to perforate or slit the casings opposite the producing formation in some of their wells to permit water to enter the formation. However, as many operators viewed the practice with skepticism and considered it to be in violation of oil-conservation principles,- systematic water-flooding was not initiated until the Pennsylvania legislature, in 1921, enacted a law authorizing water-flooding of oil sands in that State.Although water-flooding has been practiced in a haphazard manner for more than 25 years in Chautauqua and Montgomery Counties, Kansas, planned or systematic water-flooding in that State had its inception in 1935, when the legislature, following the example of Pennsylvania, also passed a lava/ authorizing water-flooding. The early operations and, to some extent, those still, practiced in the Chautauqua-Montgomery area consisted in raising or perforating the casing to allow water from upper strata to gravitate into underlying oil-producing formations. The extent to which this type of water-flooding affected petroleum production in the old stripper area of eastern Kansas is not known, but it is known to have increased oil production ap¬preciably from many leases.Following enactment of the law permitting water-flooding in Kansas, three operators inaugurated, in that same year, three organized flooding projects in three different counties of the southeastern part of the State. The first organized project on record was that of the York State Oil Co. in the Seeley pool, Greenwood County. On this project, the injection was started on May 15, 1935, into the Bartlesville sandstone at a top depth of 1940 feet."

Jul 1, 1944

By L. J. E. Hofer

"INTRODUCTION This paper is riot to be considered a complete survey of data on carbides; it is only an attempt to correlate the more reliable of the existing data of interest in connection with the Fischer-Tropsch synthesis, and its purpose is to guide future experiment and thought.A general review of the literature on the Fischer-Tropsch synthesis will be published in the near future as a chapter by H. H. Storch for a book entitled, ""The Chemical Utilization of Coal,"" edited by H. H. Lowry. This chapter covers the literature up to l9). It is planned to bring the review up to date in a comprehensive bulletin on Synthetic Liquid Fuel Processes to be completed during the next year. ACKNOWLEDGEMENTSThe author discussed the significance of the data with several members of the Physical Chemistry and Hydrogenation Section.THE PREPARATION OF CARBIDES OF IRON, COBALT, AND NICKELThe reaction of carbon monoxide with Fischer-Tropsch metals was first studied in a quanitaive way by Bahr and his coworkers. The contents of their first papers, 3/ 4/ 5/ which deal with the action of carbon monoxide on nickel, cobalt, and iron, will be described in the following paragraphs, together with the pertinent results of other investigators."

Jul 1, 1944

By Louis H. Berkelhamer

"INTRODUCTION The method of differential thermal analysis suggested by Le Chatelier (1)1 in 1887 has recently emerged as an outstanding means of studying the constitution of various substances, particularly clays, soils, and miscellaneous hydrous materials (2). The literature ably discusses the applications and results obtained but has paid too little attention to specific details of construction of the apparatus. Knowledge of the apparatus is of importance to the experienced research man as is extremely useful to the novice v ho ventures into this field of analysis. Further, it is generally acknowledged that the variations in design and conditions of operation are one of the essential causes for differences in characteristic temperatures as reported by various investigators. A step forward in the elimination of such differences is the publication of the details of construction and operation of a simple and inexpensive apparatus that has proved useful at the southern Experiment station of the Bureau of Mines, where it was used in cooperation with the University of Alabama, Tuscaloosa, Ala."

Jul 1, 1944