Search Documents

By H. J. R. Way

THE work to be described was undertaken at various periods from 1937 to 1939 on the Busia gold field, in the eastern province of Uganda. It was decided to examine the possibility of reef prospection by the resistivity method, for it was not known how far the usually disintegrated nature of most reefs in the ubiquitous laterite near the surface would obscure indications obtained by resistivity traverses. The work at the commencement was therefore largely experimental, but the results obtained thereby were satisfactory, and a survey was started at the Government closed area at Amonikakine. With the limited time and resources at the writer's disposal, it was not possible to complete the survey to his satisfaction or to follow up exhaustively all the geophysical indications, but some of the results of the experimental work and the survey were of sufficient interest to be worth recording; in particular the relation between the width of reef, electrode separation and shape of the curve, and the interference effect of constant separation curves over zones of float are significant and useful. Three new veins were located, but only one contained sufficient gold to warrant detailed prospection. This was called the Geophysical reef, and was uncovered over a strike distance of 1140 ft., and there are indications that it extends over a distance of 1990 ft. These results and the recommendations consequent therefrom were embodied in a special report to the Uganda Geological Survey. HISTORY OF THE FIELD The Busia field is in the southeastern corner of Uganda near the Kenya-Uganda border, and is about 17 miles north of the northeastern corner of Lake Victoria. Gold was first discovered in the area in the stream beds by Davies1,2 in 1932. Subsequently numerous small alluvial claims were worked by prospectors and the area was prospected for reef by a company for periods varying from three to nine months, but was finally abandoned, as the results were considered unfavorable. Further prospecting by the Geological Survey in 1935-1936 under Davies3 and later under the writer4 uncovered three reefs with sufficient gold values to be of economic interest. These were finally taken over by a company known as Borderland Syndicate, which still owns the area, and from September 1937 to the end of 1941 about 13,000 oz. of gold was extracted from reefs of the area proved by the Geological Survey. Opencast mining operations are still proceeding (February 1943). The Amonikakine area lies to the immediate north of that of Borderland Syndicate. A certain amount of prospecting had been done when the writer started work there. As a result of his report, this area was taken over by another syndicate, but little further work was accomplished before it ceased operating because of difficulties of wartime working.

Jan 1, 1944

By J. A. Thompson, M. A. Mayers

In recent years, the problem of damage to coke-oven walls by expanding coal charges undergoing carbonization has engaged great attention on the part of research workers in this field, and has led to the development of many devices for estimating these pressures.l-14 Only in Russell's method" and in the Koppers ovens7 are conditions quite similar to those in commercial ovens. Tests even in these ovens are empirical because no information has been published to permit an evaluation of "scale effects." Owing to the relatively large wall area in these test ovens, the average wall pressure determined may be lower than that existing in localized areas. This factor may be compensated for in part by the testing of coal charged into the test oven at a bulk density that is as high as the highest that is believed to exist in commercial ovens. Both of these lacks might be filled by the development of an adequate gauge for the direct measurement of wall pressure exerted by the charge in commercial coke ovens in normal operation. Previous attempts to elaborate such instruments7,15 have resulted in units which, because they had to be water-cooled, probably produced changes in the conditions of carbonization, and which had to be removed from the oven before carbonization was complete, to avoid their destruction. Late in 1941 the Coal Research Laboratory undertook to develop such a gauge, in which gas pressure was balanced against the charge pressure and which thus would not require water cooling, on a suggestion made in 1937 by one of the present authors and William B. Warren, a former member of the Laboratory staff. The gauge heads themselves were to be simple and cheap enough so that they might be discarded after each run if seriously damaged. This would permit them to be left in place throughout the carbonizing period, when they could be pushed out with the coke. The basis of the design, of which the latest exemplification is shown in Fig. I, was that as the internal gas pressure within a flexible metal envelope was increased, the flexible wall would move away from a stop when the gas pressure just overbalanced the charge pressure. If the stop were an insulated electrical contact, the point of balance could be indicated by the breaking of an electric circuit. It was anticipated that, while the instrument must operate at high temperature, the presence of a strongly reducing atmosphere throughout the carbonizing period would so reduce the danger of scaling that mild steel could be used for the gauge. This expectation has been justified. Danger of attack on silica oven walls by the steel gauge body can be eliminated by cementing asbestos paper or an alundum or silica plate to the back of the gauge body. The gauge head itself has a relatively heavy mild-steel body, A, into which standard ¼-in. pipe B is screwed to conduct gas and electrical leads. The body is closed by a single bellows C, consisting of two annuli of 0.011-in. (o.a8-mm.) cold-rolled shim-steel spot-welded together at their outside edges. The lower one is

Jan 1, 1944

By L. P. Davidson

The new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, 111., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the , equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment snd recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching period, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutid'ns can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—either as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" BC. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1944

By F. W. Jessen, F. W. Rols-Hausen

It is the purpose of this paper to present data on brines occurring in the Frio formation of the Texas Gulf Coast, and to show how their composition varies, (1) with depth below the surface, (2) with depth below the top of the formation, and (3) along the approximate strike. The brines vary in chloride content from 3,180 to 73,000 p.p.m., though the average salinity of the salt waters is shown to vary with total depth; the concentration being 35,000 to 40,000 p.p.m. at 3500 to 5500 ft., slightly less than 50,000 p.p.m. chloride at 5500 to 6500 ft. and average 38,000 to 40,000 below 6500 feet. From the analyses available, it appears that the highest concentration of salts occurs in the upper 300 ft. of the formation, while lower salinity is found with increasing depth below this point. The salt waters from wells in Starr County show less concentration of dissolved salts than in any other group of wells farther north along the strike. In all, 116 analyses from 63 fields and 14 wildcats, from depths ranging from 1300 to 11,400 ft. below the surface and from z to 3240 ft. below the top of the Frio, are recorded. Introduction Brines have been studied for many Years in an attempt to solve some of the geologic and production problems associated with the production of oil and gas. One practical application of study of . water analyses is the correlation of waters occurring above, in, or below the producing sand in the same field or throughout the same formation. The Frio formation, the series of sands and shales occurring below the Marginulina zone and above the Vicksburg, is one of the major oil and gas-producing formations in the Texas Gulf Coast. Fossils are rare or absent in the upper Frio throughout most of the area. When available, cuttings and cores, and electric logs were used to determine the top of the Frio. A change in lithology was used to determine this point in most of the wells, and fossils were used in some of the deep wells. It is realized that a change in lithology is not perfect for correlation purposes over long distances and some of the trends may be influenced by the inability to differentiate between the nonfossiliferous Marginulina zone and the Frio. It underlies virtually all the area shown on the accompanying map (Fig. I). Although it is not productive in the updip facies, it has been explored to a limited degree below I2,000 ft. Further more, toward the coast line future drilling to deeper depths should encounter this formation. Although thousands of wells have penetrated or drilled entirely through the formation, very few water samples have been secured from the many sands occurring in this formation and analyzed. Previous Investigation No previous published study has been made of the chemical composition and concentration of waters from the Frio formation. However, one water analysis

Jan 1, 1944

By James K. Stanley

Preferred orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.' In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurnical -literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanicai properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important information, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational understanding of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required—it is only necessary to punch or machine a I-in. disk of the sheet material and insert it into the testing device.

Jan 1, 1944

By W. D, D. W. Mounce, W. M. Rust

The almost universal acceptance of electrical logging by the petroleum industry calls for a critical examination of the physical bases of the common methods. This is particularly needed for the natural potential log. The conventional explanations are based on the phenomena of electrofiltration and electro-osmosis. However, experimental data show that they fail to give a basis that is quantitatively sound. Moreover, they lead to interpretations of details of electrical logs that are erroneous. It was found experimentally that when a plug of shale is placed in a chain of dissimilar electrolytes, a current flow results. Experiments on oil-well cores and fluids similar to those existing in wells show that potentials are set up which are in reasonable agreement with those encountered in electrical logging. Doubtless other sources of potential are important but this explanation not only accounts for much of the potential but also clarifies some fairly familiar examples of misinterpretations. Introduction The extraordinary value of electrical well logging as a tool for petroleum engineers and geologists is now so uni- versally recognized that it is not necessary to point out the ways in which it can be useful. It is sufficient to mention only the saving that has resulted from the elimination of much coring that would have been necessary under former practices and the considerable additions to reserves resulting from the discovery of sands missed in coring. Paradoxically, the very remarkable success that has resulted from the application of electrical logging to correlation and completion problems has cost some of its most consistent users dearly.' The fact that some operators have placed unwarranted faith in erroneous interpretations of electrical logs does not reduce the value of the logs. It should, however, make one pause long enough to ask why experienced users should be misled. The answer to this question is not hard to find. In nearly every case, the fault has been oversimplification. This is illustrated very aptly by the familiar interpretation and theory of the natural potential log. Recording and Interpreting Logs The natural potential log is extremely simple to record precisely enough for all present-day uses. One needs only an electrode, a cable to lower the electrode through the drilling mud, a recording meter and a surface ground connection. The electrode can be elaborate but need not be. A simple brass rod 2 in, in diameter and 2 or 3 in. long is quite satisfactory. The cable need not be particularly well insulated, nor need it have a very low resistance. The recorder can be a vacuum-tube 1 References are at the end of the paper.

Jan 1, 1944

By Robert F. Mehl

Jan 1, 1944

By Robert W. Metcalf

Corundum, natural alumina, or aluminum oxide (A1203) is the hardest mineral known except diamond. Theoretical composition is Al 52.9 percent and 0 17.1 percent, but it always contains small quantities of impurities, chiefly silica, iron, and lime. The melting point of corundum is above 1950° C., and it is insoluble in the strongest acids. Its hardness (9 on the Mohs scale) varies slightly according to purity, and its specific Gravity ranges from 3.95 to 4.10, 4 being a fair average. The index of refraction is 1.760 to 1.768 and its streak is white. Luster is adamantine to Vitreous, come specimens pearly, and color varies widely from white, gray, pink, and blue to black, brown, or bronze. Gem varieties are transparent or translucent, and of more brilliant coloring - red, blue, yellow, purple, or green. Corundum occurs in opaque massive or block structure with parting planes little developed or only roughly delineated and in granular form as minute crystals or small, irregular grains interspersed throughout the contact zones of schists and gneisses.

Jan 1, 1944

By Oliver C. Ralston

Fluorescence is of growing interest to the mineral industry because certain minerals may be detected thereby and because, as shown in figure 1,4/ many minerals (natural or synthetic) are needed in tubes and lamps. The use of fluorescent lighting is expanding, and large numbers of lamps of many sizes and shapes are being made and used in works, factories, stores, offices, homes, and in photography. Fluorescent tubes, as distinguished from clear tubes filled with neon, argon, or other rare gases through which a current of electricity passes, fluoresce owing to specially, selected and prepared minerals placed in the tubes. Luminous chemicals and paints also contain special minerals and are used in similar applications; therefore, these also will be considered in this report. Although the quantity of minerals (in tons) that are used for fluorescent purposes is small, and probably will continue to be so, this use is significant because it exemplifies a requirement for "pure" minerals in which a trace of contaminant as" minute" as one part in ten million may distinguish between the acceptance or rejection of a particular material. This extreme purity makes synthetic minerals almost essential, and natural mineral's are now little used.

Jan 1, 1944

By P. W. Bridgman

FLOW and fracture are admittedly complicated phenomena of which we are yet only partially masters. There is not even universal agreement as to the details of the language best adapted merely to describe the phenomena, to say nothing of any theory. Certain points of view, however, are widely held, and there are certain general expectations as to what sort of procedures will prove permissible. A complete description of any situation involving fracture would demand a complete history of all the variables in the control of the experimenter. The experimenter endeavors so to choose his independent variables that they are adequate to determine completely the situation in the sense that when an experiment is repeated on the same initial material and with the independent variables running through the same sequence, all the other measurable properties of the system will also run through the same course. It is, I think, the universal conviction that when we are dealing with phenomena of flow and fracture, the most important of the necessary variables are the external forces acting on the various parts of the body; when the force history repeats, with certain obvious restrictions such as that temperature must be constant and non- mechanical forces, such as magnetic field, must be small enough to be ineffective, then the history of all measurable properties will repeat; in particular the alteration of geometrical shape due to flow will run through the same course, and when fracture comes, the character of the fracture will be reproduced. Complete mastery of merely the descriptive aspects of flow and fracture would demand the ability to predict the entire course of flow and complete characterization of the final fracture for every possible combination of forces, varying in time in all possible ways, when applied to bodies of all possible shapes. This full situation is obviously of prohibitive complexity. The first stage in reduction to manage- able simplicity is to resolve the total situation into the sum of contributions made by small elements. Our thesis is that if each of the elements is adequately characterized, the behavior of the whole system is fixed. The element is usually taken of a simple geometrical shape, suggested by the mathematics best adapted to the particular situation. The forces acting across the faces of the elements are ultimately determined by the forces acting across the free faces of the whole system. The detailed process of finding the precise forces on the faces of all the elements in terms of the external forces involves the use of a special mathematical invention, the stress, a constructional quantity consisting of six components. The stress at any point in the body is determined by both the external force system and by the physical properties of the body at all points; quite different stresses prevail at the interior of bodies of the same shape under the same external forces in the elastic and plastic ranges. The forces on the faces of any element are, however, uniquely determined by the stress system at the element. Our fundamental thesis

Jan 1, 1944

By Alfred H. Bell, Charles W. Carter

In 1943, Illinois produced 82,256,000 bbl. of oil, or 5.5 per cent of the total for the United States, and ranked sixth in the nation in oil production. This represents a decline of 23 per cent from 1942, when the total Illinois production was 106,ggo,o~~ bbl. and Illinois ranked fifth. The daily average production for 1943 was approximately 225,000 bbl. Daily averages by months were as follows: Jan......... 238,000 July......... 218,000 Feb......... 240,000 Aug......... 216,000 Mar......... 237,qoo Sept........ 220,ooo Apr......... 230,000 Oct......... 220,000 May....... 221,000 Nov......... 223,000 June......; . 222,000 Dec......... z18,ooo This shows that most of the decline during the year took place between March and May, and that for the last eight months of 1943 production has been essentially steady. This means that there has been enough production from new wells drilled to balance the natural decline of the Older wells. The trends of drilling and production are shown in Fig. I and Table 3.

Jan 1, 1944

By Kenneth G. Skinner

Diatomite, also known as diatomaceous earth, diatomaceous silica, kieselguhr, and moler, has been used extensively for many years, but only during the past two decades has it become an important industrial mineral. United States sales for 1.936-38 totaled almost 280,010 tons,7 but relatively little (with the exception of that sold by an Oregon company affiliated with a larger California company) was sold by Pacific Northwest producers. In attempting to develop some of the many Pacific Northwest diatomite deposits, these producers have been handicapped by lack of published technical information regarding processing methods and the suitability of different deposits for specific uses. To determine some of the physical and chemical properties of known Pacific Northwest diatomites, the present investigation was started in 1938 by the Bureau of Mines in cooperation with the College of Mines, University of Washington. Figure 1 shows the location of deposits sampled. Because most relatively pure diatomites can be used as concrete admixtures or as inert fillers in rubber, paints, and plastics, this investigation concentrated upon determining some filter-aid characteristics and their relationship to other physical properties. A filter-aid is a powdered material that, when added to solutions to be filtered, improves flow rate, filtrate clarity, or both. Some chemical analyses also were made.

Jan 1, 1944

By Gerald Edmunds

The liquidus line on the phase diagram for temperature versus composition of a binary alloy system, representing the boundary between the homogeneous melt and the heterogeneous melt plus solid, besides showing the minimum casting temperature, is useful in determining eutectic compositions and the presence of phase changes such as peritectic transformations and intermetallic compound formation. The liquidus often is determined by the cooling curves of thermal analysis, but supercooling frequently occurs, so that the temperature values are low. An alternative method, the one employed here, consists of determining the composition of samples of the melts from heterogeneous alloys that are at equilibrium. With meticulous attention to fundamentals, this method is capable of yielding values limited in precision only by the temperature control and measurement and analyses. Apparatus By starting, on the one hand, with a supersaturated solution and allowing the excess solute to precipitate, and on the other hand with an undersaturated solution and allowing more of the solute to be dissolved, both processes being carried out at the same temperature, equilibrium may be said to have been approached from both directions; that is, from above and from below. If the analyses show the solutions to contain the same fraction of solute when equilibrium has been approached from above and from below, one is assured that equilibrium has been reached in both determinations. In order to carry out such determinations, it is necessary to have equipment for obtaining and maintaining the proper temperatures; for holding the melt, measuring its temperature, and stirring, sampling and analyzing it. The present work required temperatures from 420° to 900°C. The equipment consisted of: A furnace, which was a vertical alundum tube, 13/4-in. diameter inside and 18 in. long, wound with Nichrome resistance wire, surrounded by a 3-in. i.d. alundum tube wound for 5 in. of length near each end, for compensation of end losses. This muffle was contained in an iron shell with Transite end plates, the intervening space being packed with Sil-O-Cel. The outside dimensions of the furnace were 12 in. in diameter by 181/2 in. in height. Heating current was supplied by three independent variable-voltage transformers (Variac), one connected to each end compensator winding and manually controlled, and one connected to the main winding through a series resistance of 5 ohms. This resistance was short-circuited for

Jan 1, 1944

By T. S. Spicer, C. C. Wright, R. G. Bowman

In recent years considerable publicity has been given to the problem of atmospheric pollution by fuel-burning equipment. Legislation has been stimulated and smoke ordinances have been enacted, the provisions of which show a definite trend toward stricter control of the emissions not only from the stacks of industrial fuel users but also from the chimneys of domestic consumers. As a result of war conditions, some slackening in the enforcement of these ordinances may be noted, but this is only a temporary expediency caused by the changes necessary in the distribution of the nation's fuel supplies and difficulties in securing the necessary equipment. Previous trends may be expected to continue in the postwar period. Largely because of the consumer demand for automatic heat, but partly because of the legislation against smoke emission, there has been a marked increase in the use of domestic underfeed stokers with the past decade. When correctly adjusted and operated, these units reduce the smoke emission materially, so that even the high-volatile bituminous coals may be burned with little or no emission of objectionable smoke. Unfortunately, however, the use of the domestic underfeed stoker introduces another problem; namely, fly-ash. Production of Fly-ash The term "fly-ash" is a misnomer, since the fly material is generally a mixture of small carbonaceous particles varying from green coal to coke, and inorganic particles ranging from fluffy ash to small particles of fused clinker. For want of a more comprehensive name, however, the term fly-ash is used throughout this paper to include all the fly material. Even with hand-fired furnaces a certain amount of fly-ash is produced, which necessitates periodic cleaning of the boiler flues or furnace radiator, the smoke pipe, and occasionally the chimney itself. With stoker operations the amount of fly-ash is increased many fold, because of the higher velocity of air travel through the fuel bed. Frequently the amount of this fly-ash attains such proportions as to constitute a definite nuisance to the householder and his neighbors and distracts very materially from the otherwise automatic or semi-automatic performance of the stoker. Virtually all the boilers and hot-air

Jan 1, 1944

By W. M. Peirce

Commencing in 1922, each year a lecture has been presented to the Institute of Metals Division at this February meeting. The range of subjects has been very- broad. Some speakers have dealt with the most advanced work in the very heart of the science of physical metallurgy. Others have stimulated our imaginations by discussing the most recent progress in related fields of science. Others have told us of the latest art, which is at any moment of greater practical importance than the latest science, of metals. I feel that this broad precedent in the choice of subjects will justify my choosing to talk about some of the prosaic details of how, during the last generation, industry has effectively organized research to accelerate progress in our own and all other fields of science and related art. A number of years ago I visited one of this country's well-known research laboratories and had the pleasure of chatting for a few minutes with its equally well-known director. Being particularly interested at the time in the organization problems connected with industrial research, I broached that subject. My host stated in effect that he didn't believe in organized research. He was, of course, resorting to a rhetorical hyperbole. to pain: out the danger of overorganization which can so easily drift into regimentation and destroy individual initiative. Actually nearly all of us, much as we cherish our personal freedom of action, believe in organization because the history of progress in every field of human activity has been a history of men learning to work together, to cooperate, to create an efficient division of labor. We use organization to achieve this coordination. At the same time our form of organization must not stifle individual initiative or it will prove a deterrent rather than an aid to accomplishment. Research, too, must be organized for greatest achievement but especial skill and care are perhaps needed to avoid stifling the initiative of the individual workers. I have, of course, followed with keen interest and much benefit the vast amount . that has been said and written on this subject in the past twenty years but I still find new stimulation in discussions with my good friends working in this field. It is my hope that this discussion may serve a like purpose. It would be ungracious not to make due acknowledgment to the many able contributors to this particular phase of human progress, but their very number and the great volume of their writing makes it impossible to trace to any one individual a particular significant and valuable idea. I shall content myself therefore with this general acknowledgment and with acknowledgment of the specific debt that every research man owes to those who have so ably kept before the public, and in particular before industrial executives, the place of research in the modern scheme of things' Because of the legitimate publicity thus given to research, the day is past when any

Jan 1, 1944

By A. L. Marshall, F. J. Norton

The object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate, of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. Apparatus and Technique The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system , will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 1800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by unscrewing the lower nut, and the new

Jan 1, 1944

By C. L. Mantell

When considered from the viewpoint of world annual output, tin is one of the rarest metals. Its annual production is exceeded by that of iron, copper, lead, zinc. aluminum, magnesium; probably by that of the ferroalloys of manganese, chromium, and silicon, and possibly by the world production of sodium; while it exceeds only the output of such common metals as nickel, antimony, mercury, tungsten, molybdenum, silver, gold and the precious metals. Cassiterite, or tinstone, until the second World War was the only mineral that was an important source of tin. This mineral is frequently called "tin ore." The use of the term should be restricted to the ore containing the mineral, and not, in addition, to the concentrates of the mineral obtained from the ore or from stanniferous alluvial deposits. There is a general misuse of the term "tin ore" in the Malay Peninsula and adjacent localities, particularly where most of the mineral is obtained from secondary stanniferous deposits. The term "cassit-erite" is exclusively used in mineralogical, geological, and other scientific writings; it is unfortunate that it is not mole frequently used when referring to the occurrence of the mineral on an economic scale. Ores "Tinstone" js a very convenient old English term deserving a more frequent use. Tinstone is a dioxide of tin, or stannic oxide. When chemically Pure, as in the very rare transparent variety, it has a metallic content of 78.6 per cent tin. Frequently, however, the crystals and grains contain appreciable amounts of impurities, chiefly iron and tantalum. The impurities here referred to are those actually in the mineral itself. Tinstone usually has a deep brown or black color with an adamantine luster. Several other colored varieties are known, among them red ruby tin, yellow rosin tin, and yellow wax tin. the names jn each case being descriptive of the mineral's appearance. Ainalite is a variety of cassiterite con-taining almost g per cent of tantalum pentoxide. Sparable tin, tooth tin, and needle tin, as a result of their acute dite-tragonal pyramidal crystalline form, re-ceive their names from their crystallo-graphic appearance. Wood tin is a compact variety of cassiterite composed of radiating fibers resembling dry wood. Toad's-eye tin is a similar variety on a smaller scale in which the fibers appear to resemble the eye of a toad. Stream tin is water-worn tin-stone. Float tin is sometimes employed to describe the cassiterite occurring in soil derived from the weathered surface of a mineralized area. Stannite is an ore of tin of lesser impor-tance than cassiterite. It is a sulphide of tin, copper, and iron, sometimes known as tin pyrites or bell-metal ore. Its chemical com-position is sometimes expressed by the for-mula Cu,S.FeS.SnSz with zinc usually present in varying quantities. The tin con-tent varies from 22 to 27 per cent and there is about 29 per cent of copper, 13 per cent of iron, and 30 Per cent of sulphur.

Jan 1, 1944

By F. Keller, A. H. Geisler

Some of the important changes that take place in the structure of aluminum alloys are largely submicroscopic in character. This is especially true of the changes that accompany age-hardening and recrystallization. Although improved metallographic practices have been helpful in indicating some of these changes indirectly, results are limited by the resolving power of optical microscope lenses. The electron microscope, however, provides a new and important means for investigating the fine structure of metals in a range not possible heretofore. It is anticipated that this microscope will yield new and useful information to metallurgists when suitable techniques are developed to utilize its very high resolving power. Several unique methods have been devised to permit the examination of the structure of opaque samples by the electron microscope. These are all based on the principle of producing a very thin film that represents the prepared surface of the opaque metal sample, which can be examined in the transmission microscope; however, the available methods fall into three categories, depending on the manner in which the film is obtained. With the oxide-film method developed by Mahl3-17 a very thin surface layer of the metallographic sample is converted into oxide by a thermal, chemical or anodic treatment. After removal from the metal sample by one of the special techniques described by Evans,19 this oxide film is examined in the electron microscope, and is found to portray the structure of the original metal surface. Films formed on aluminum,8,17 nickel,7 iron 3,8,9 and a nickel-beryllium alloy" by heating; films formed on iron 8.9 by chemical action; and films formed on aluminum3-16 by anodic oxidation, have been examined. The other two are more recent methods developed principally in this country; they consist in making the thin film in the form of a mold or replica of the surface contour of an etched sample. With the negative replica method the thin film is made directly on the sample; with the positive replica method it is made on a negative reproduction of the sample. With both methods, variations in the contour of the metal sample, caused mainly by etching, produce variations in the thickness of the surface replica. Because of the direct dependence of the amount of scattering of the illuminating electrons upon the thickness of the film penetrated, only the variations in thickness of the replica are responsible for tones in the electron image. Negative replicas are made by forming a thin film of some suitable material directly on the polished and etched metal sample, and derive their name from the fact that after removal from the sample they have the high and low points in the sample reversed, as shown in Fig. I. Nega-

Jan 1, 1944

By J. D. Price, G. V. Woody

Many producers of by-product coke have spent considerable time and given considerable thought to the use of a substitute for low-volatile coal as an admixture with high-volatile coking coal for charging high-temperature by-product coke ovens. Generally speaking, there are two principal reasons for this, one being occasioned by the lack, in certain localities, of low-volatile coal delivered at a cost sufficiently low to permit its use, and another being the desirability of finding a substitute product with a delivered cost lower than the cost of the low-volatile coal. It was for the first of these reasons that the Colorado Fuel and Iron Corporation was particularly interested in this subject. This paper deals with the experimental work and the results obtained by that company in producing and using low-temperature char. Overcoming Defects in Coke from Colorado Coals Colorado coking coals are all of the high-volatile type and were all laid down during the Cretaceous period, which makes them something like 80 million or so years younger, geologically, than eastern coals. They behave, when coked alone, something like the Pittsburgh-seam coals. They make a very brittle, highly cross-fractured, fingery coke of fair shatter value but quite low in resistance to abrasion. Mixed with a low-volatile coking coal such as Poca- hontas or certain Oklahoma coals, they make a coke that is equal to virtually any of the eastern cokes. The inferior quality of Colorado coke has long been recognized, and a considerable amount of time, effort and money has been spent upon investigations of means for improving its physical properties. While it has been found that some improvement in quality of coke can be secured by the adjustment and control of such variables as pulverization, moisture content, oven temperature and bulk density of charge, and through the addition of certain inert materials such as pulverized coke breeze, pitch, high-volatile noncoking or semicoking coal, the benefits so gained have been comparatively small. There are no low or medium-volatile coking coals available within a reasonable freight-cost distance. Therefore a substitute for low-vol-atile coal was developed through low-tem-perature carbonization—or, more correctly speaking, through the partial devolatiliza-tion—of high-volatile coals. The blending of this lower volatile char with the high-volatile coking coal distinctly improves the quality of coke made from Colorado coal. There is nothing especially new about this idea. In 1908 a Japanese patent was taken out by Kotaro Shimomura, whose claim was: The method of making a nonfingery coke out of bituminous coals, without using natural coals of low-volatile matter; according to which a certain coal is heated at a temperature between about 300°C. and about 600°C. so as to leave about 15 to 25 per cent volatile matter in the coal; this coal is mixed with the

Jan 1, 1944

By David H. Davis, John Griffen

Much of the ground to be covered by this paper was ably covered by a paper presented by Messrs. Morrow and Jordan1 before a joint meeting of the Iron and Steel Section of the Engineers Society of West-ern Pennsylvania and the A.I.M.E. Pitts-burgh Section at Pittsburgh in the spring of 1940. As that paper was not published, the present authors have availed them-selves of Mr. Morrow's kind permission to use information given therein. Similar figures for the latest years available have been added to many statistics originally presented. It is unfortunate that Mr. Jordan's death removes his stimulating guidance and help, which the authors would have welcomed and have found invaluable in the past. One interested in the Pittsburgh seam should not fail to read the exhaustive and authoritative paper by Eavenson2 presented in 1938. As Allegheny, Fayette, Greene, Washington, and Westmoreland Counties contain practically all the reserves and furnish nearly all of the production from the Pittsburgh seam in Pennsylvania at the present time, this area only is intended when reference is made to the Pittsburgh seam in Pennsylvania. On much of the seam in Greene and Washington Counties, which contain a large proportion of the total reserves, insufficient data are available to determine the detailed characteristics of the seam with any degree of finality. It is hoped that the data presented here will fairly well indicate the probable characteristics. Economic Importance of the Pittsburgh Seam The Pittsburgh seam in Pennsylvania is of primary importance as a coal resource, not only because of its substantial reserves but because it contributes such a large proportion of the coal used in the country and an even larger proportion of that used in the manufacture of coke. Mr. Ashley3 placed the estimated recoverable reserves (1935) of the Pittsburgh coal bed in Pennsylvania at 7,500,000,000 tons.* Although a considerable portion of this tonnage is not now suitable for coking coal, because of its high sulphur content, undoubtedly the supply of coking coal will last for many years and that not suitable for coking will furnish industry with an ample supply of energy. In attempting to assess the contribution of the Pittsburgh seam to total coal production and to that of coal used in making coke, one finds that the statistics published annually by the U. S. Bureau of Mines, Minerals Yearbook, do not give tonnages classified as to seams but only as to districts or states and counties. However, it happens that, at present and during much of the

Jan 1, 1944