Search Documents

By V. O. Tenorio, J. Puell

"Dump design is critical to effective mine planning in large scale open pit mines. Capital and haulage costs are considerable from early stages and through the life-of-mine as these dumps gradually become immense structures. Delivered mining rates, as well as certain spatial and physical constraints, provide a set of parameters of mathematical and economic relationship that creates opportunities for modeling and thus facilitates the measuring and optimization of ultimate dump design by using programming and empirical techniques while achieving economic objectives. This paper presents a methodology to optimize the ultimate dump design by minimizing its total dumping costs. The methodology consists of the formulation of a generalized model based on the relationship of the main dump parameters, followed by the use of linear programming to find the solution that minimizes the haulage total cost, and finally through a series of iterations, modifies the preliminary solution by projecting it to the topography and creating the ultimate dump design. A case study applied to a waste dump exemplifies this methodology. INTRODUCTION Open pit mine operations move large amounts of material on a daily basis from the shovel faces to the appropriate destination points. Hustrulid et al. identified three major destination places where the material receives downstream treatment after its delivery: mill processing, leaching dumps, and waste rock dumps [1]. The corresponding destination is given by a cut-off grade criteria, ore type, and the possibility of obtaining the maximum metal recovery. Dump leaching technologies have developed substantially since 1975 [2], and have enabled mining facilities to beneficiate low grade sulfide and oxide ores. As a consequence, the number of active dumps have increased since then and the entire mine configuration, which is limited in itself, has changed. The proper location, design, and construction of a mine dump must serve the safety, environmental and economic goals of the long-range mine plans. Therefore, an optimized use of the available surface area in the mine is highly desired."

Jan 1, 2018

By Antonio Segatori, Bjørn Holmedal, Kai Zhang, Trond Aukrust, Knut Marthinsen

"The visual appearance and mechanical properties of aluminium alloy extrusions are strongly dependent on the microstructure and texture of the extruded profiles, where the desired microstructure and texture may depend on the specific applications. In the present work, the evolution of deformation, as well as recrystallization textures during extrusion of AA6xxx aluminium alloys, have been experimentally and numerically investigated. Extrusion trials were performed in a laboratory extrusion set-up, which enabled immediate water-quenching of the profiles at the exit of the die, and thus the possibility to capture the deformation texture prior to post-extrusion recrystallization. The textures and their through-thickness variations were experimentally measured by the electron back-scatter diffraction technique (EBSD, and the deformation textures numerically modelled by coupling FEM flow simulations and crystal plasticity (CP) simulations. Different CP models as well as different choices of model parameters were employed and evaluated for texture predictions. With an appropriate choice of crystal plasticity model and model parameters, the deformation texture can mainly be predicted, although the accurate intensities are hard to reproduce. The corresponding recrystallization textures, either generated through spontaneous recrystallization of the extruded profiles or through post-extrusion annealing, are far more challenging to reproduce with available recrystallization models.INTRODUCTION Extrusion is a widely applied thermal-mechanical process to produce aluminium profiles. The properties of the profiles, for example mechanical, fatigue, fracture, corrosion as well surface appearance, are strongly dependent on the underlying microstructure and texture, and the requirements with respect to these aspects may vary with applications (Ralston et al., 2010; Dumoulin et al., 2012; Donati et al., 2013). Moreover, it is often a challenge to produce extrusions with a consistent and homogenous grain structure and texture along as well as through the cross section of the profiles. It is thus vital to understand and be able to predict (model) how different microstructures and textures are formed and how they evolve during and after extrusion, as basis for controlling the final appearance and properties of extruded profiles."

Jan 1, 2018

By P. Gao, J. W. Yu

"Pre-concentration is a necessary step for upgrading low-grade iron ores, and its aim is to remove gangue minerals for improving efficiency of downstream separation process. The most important pre-concentration technique for iron ores, including hematite, siderite and limonite, is magnetic separation based on the appreciable differences between the desired iron minerals and gangue minerals in magnetic susceptibility. In this paper, the separation efficiency of one-stage low-intensity magnetic roughing combined with two-stage high-gradient magnetic scavenging for the pre-concentration of a low-grade hematite from Donganshan was investigated. It is a BIF type of ore containing hematite, magnetite and a bit of siderite, and an average content of Fe is about 34.6%. The effects of grinding fineness and magnetic field intensity for scavenging I and II were studied and optimized. The results showed that a magnetic preconcentrate assaying 42.7% with a recovery of 95.4% was obtained under the conditions of ore grinding fineness of -74 µm 70%, magnetic field intensity of 300 mT and 800 mT for scavenging I and II, respectively. Over 20% of the feed was rejected as the final tailings assaying 6.4% Fe. Meanwhile, the XRD, iron chemical phase and SEM analyses of different stage products revealed that hematite, magnetite and siderite could be recovered successfully by magnetic separation. However, some ultra-fine hematite particles (-10 µm) were difficult to be captured by magnet, and lost in the final tailing, resulting in lower iron recovery.INTRODUCTION Donganshan iron ore belongs to sedimentary-metamorphic iron formation called banded iron formation (BIF), which is formed in the Precambrian with a layered structure composed of ore bodies (Shen, 2012). Such type of iron deposit contains various iron-bearing minerals like hematite, magnetite, and siderite, suggesting it may be amenable to pre-concentration with magnetic separation. The pre-concentration process is effectively applied in recovering hematite, magnetite and siderite from iron ore, due to its benefits of further upgrading iron ore and improving separation efficiency. The most important pre-concentration technique for iron ore is magnetic separation, including low-intensity magnetic separation and high-gradient magnetic separation, based on the fact that there are appreciable differences between the desired hematite, magnetite or siderite and the gangue minerals in magnetic susceptibility."

Jan 1, 2018

By J. Fox, C. Allen, A. Greth, K. Kocsis

"It is the duty of the mine operator to ensure the mine environment is healthy and safe for the mine workers. For deep and hot underground mines, this requires maintaining adequate working temperatures by means of mitigating the heat load generated by strata, auto-compression, mining equipment, explosives, ground water, and human metabolism. The heat load is best reduced by minimizing the amount of heat transferred to the mine air from these sources and through the use of efficient ventilation with effective cooling systems. The heat emitted by mining equipment and vehicles contribute a significant proportion to the combined heat load of an underground mine. This is especially a problem for diesel equipment due to the fact that besides heat, a large amount of water vapor is produced, which increases the humidity in the production workings. Diesel engines have proven advantageous in recent history due to their high power output and reliability. However, as mines continue to become more mechanized and deeper the climatic problems introduced by elevated heat generation will continue to rise. With that, the issue of heat generated by diesel equipment must be addressed. The economic alternative for diesel engine equipment fleets in underground mines is the electric engine. Technological advances in battery technology, increased mechanical output and improved reliability have made the electric engine significantly more competitive in comparison to diesel engines. Because electric engines do not utilize internal combustion, the heat produced by them is significantly less than of the diesel engines. Battery powered mining equipment likewise eliminate diesel particulate matter (DPM) produced by diesel engines. Utilizing battery electric equipment in underground mines provides many advantages, such as: (a) reduced heat load, (b) healthier and safer environment for the mine workers, and (c) reduced mine operating costs due to lower ventilation requirements. This paper will highlight the health and cost benefits of using battery/electric fleets versus diesel fleets in deep and hot underground mines. The study analyzes simulations produced from thermodynamic ventilation models. Early simulations show significant cost reductions in terms of net present value (NPV) when comparing the air volume requirements for battery/electric equipment versus diesel powered equipment for the same production rate. INTRODUCTION The competitiveness of the world mineral market demands that mine operators continue to increase production and decrease costs as commodity prices fluctuate in often unplanned directions. This has forced underground mines to operate at deeper depths and to become more mechanized to remain competitive. Because of these changes, ventilation challenges have continued to increase as the mines combat an enlarged influx of contaminants such as heat and diesel particulate matter (DPM)."

Jan 1, 2018

By Peng Qian, Xiao Li, Guoyan Fu, Peiwei Han, Yongliang Wang, Shufeng Ye

"Arsenic removal from high arsenic gold concentrate is conducive to increase the mineral value and realize the mineral comprehensive utilization. This study investigated the alkaline pressure oxidation leaching (APOL) of an arsenical gold concentrate in lower temperature to separate the arsenic into filtrate. The effects of temperature, NaOH concentration, solid-liquid ratio, reaction pressure and stirring speed on the leaching efficiency were investigated, and the characteristics of the gold concentrate and leaching residues were evaluated using XRD and SEM analysis methods. The obtained results showed that by using lower temperature (<60?) it is possible to avoid the production of elemental sulfur during the leaching process, which is benefit for the oxidation of arsenopyrite; When the reaction was carried out under appropriate conditions, more than 98% of the arsenic will be extracted into the filtrate as the form of arsenate or thioarsenate. INTRODUCTION In recent years, there has been considerable interest in the recovery of gold from refractory arsenical gold ore. The arsenic in this kind of ore usually exists as the form of arsenopyrite, and the gold surrounded by arsenopyrite exists as the form of fine particles, which will give many difficulties to metallurgical work. When the content of arsenic in the gold ore is more than 0.5%, it will seriously penalize the smelting efficiency (Ruiz et al., 2014). So pretreatment of the refractory gold ore is necessary to obtain the largest economic value and environmental benefits (Balaz et al., 2000). The oxidation pretreatment processes mainly include roasting oxidation, pressure oxidation, chemical treatment and biological treatment (Ann et al., 1992; Kou and Chen, 2012; Tongamp et al., 2010; Fernandez et al., 1995; Lin and Zheng, 1996). Among them, the roasting oxidation and pressure oxidation are the more ordinary processes in industry. The roasting oxidation process is the mature and adaptable technology, but the production of waste gas containing sulfur and arsenic will pollute the environment. The pressure oxidation method possesses certain metallurgical and environmental advantages, and can efficiently decompose the mineral. According to the different solution media, the pretreatment can be divided into alkaline and acidic pressure leaching pretreatments (Papangelakis and Demopoulos, 1990; Hiskey and Sanchez, 1995). The acidic pressure oxidation method has been used in most smelting plants for high arsenic gold ore pretreatment, while the alkaline pressure oxidation is still not widely applied. Compared with the acidic pressure oxidation, the alkaline pressure oxidation can be realized under lower temperatures."

Jan 1, 2018

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

Green pellet strength including drop number and green compression is highly depended on particles size and shape. The used grinding method, ball mill or high pressure grinding roll (HPGR), directly vary the particle size and shape. Considering mode of pellet crack, green pellet is composed of particle-binder-moisture system. Different type of forces existed in such a system to create a stable green pellet: solid particle interaction, magnetic, binding and cohesive forces in the interface of particle-moisture. The pellet failure can occur at solid-liquid interface and/or through liquid phase. Pellet crack occurs when crack passed through entirely the plane failure. In this research, the effect of particle size and shape of pellet feed on green pellet strength has been investigated. It was deduced that green pellet strength highly improved by increase of specific surface area. The drop number and green compression strength of pellets prepared by HPGR was higher than ball mill. It was found that the main reason responsible for this difference was the particle shape. Capillary force is responsible for part of pellet force and improves by decrease of particle size. Also more elongated shape of HPGR particles resulted in higher capillary force due to thinner interface layer between particles. The less circular shape of particles lead to improvement of capillary force as can be occurred for HPGR particles. The rougher shape of HPGR particles resulted in higher wettability of particles and better diffusion of water among particles. In fact the rougher particles means lower connection angle. Aspect ratio of particles was of great importance of crack growth because the required energy of pellet failure increases directly. The required energy for pellet failure increases by increment of particle aspect ratio. The relationship among crack failure force, roughness and aspect ratio has been modeled considering 3 shape descriptors.

Jan 1, 2018

By K. C. Corin, M. S. Manono, R. M. Manenzhe, J. G. Wiese

"Environmental concerns necessitate the recycling of process water within mining operations. Given that recycled water is chemically different from fresh water, and collectors are added such that they adsorb at the liquid-particle interface, changes in the aqueous phase are expected to affect collector adsorption. A Finnish nickel-copper ore was floated in synthetic plant waters of varying ionic strengths and plant waters obtained at Boliden Kevitsa Mine, with aerophine and sodium isopropyl xanthate as collectors. Of the tested waters, the copper thickener overflow was the least conducive to xanthate adsorption and valuable mineral recovery. The nickel thickener overflow, standard process water, and raw water were the most conducive to xanthate adsorption. For the raw water and nickel thickener overflow, increased adsorption correlated with increased valuable mineral recovery. Further, recycling xanthate retained in water affected the selectivity of the collector and hence the concentrate grades.INTRODUCTIONFlotation is a separation process that exploits the differences in the surface properties of the particles being separated. The efficiency of separation is dependent on the degree of hydrophobicity achieved by the particles meant to be floated, which are, in most cases, valuable minerals. The hydrophobicity is in turn dependent on the adsorption of the chosen collector onto the surfaces of the floated particles (Fuerstenau, 1984; Taggart and Hassialis, 1946). Empirical findings suggest that species dissolved in solution strongly influence collector adsorption and overall flotation response (Fuerstenau and Chander, 1986). Due to environmental concerns, it is becoming more pertinent for mining plants to recycle process water and hence limit the usage of potable water. There is an interest to ensure minimal discharge of plant water into the environment, as this water is typically polluted with process reagents that may render it toxic (Levay et al., 2001)."

Jan 1, 2018

By X. -G. Chen, K. Liu, N. Parson

"Precipitation-strengthening 6xxx alloys are widely used for building and construction and automobile industries due to their high strength, good weldability and corrosion resistance. However, their elevated-temperature properties (250–300°C) decrease rapidly due to the fast-coarsening of precipitates. On the other hand, dispersoid-hardening is one of the most efficient approaches to improve the elevated-temperature properties. Therefore, the evolution of dispersoids during heat treatment in Al-Mg-Si-Mn alloys was investigated in the present work. Various heat treatments with temperatures ranging from 300–500°Cfor up to 24 hours were performed. Electrical conductivity and microhardness were measured while optical and scanning electron microscopy combined with image analysis, were used to characterize the dispersoids. Special emphasis was placed on the evolution of the size and number density of the dispersoids under different heat treatment parameters. It was found that dispersoids started to precipitate at 350°Cfor 1 hour. Nucleation and growth were the main mechanisms at temperatures up to 400°Cwhile coarsening occurred at temperatures above 450°C. The quantitative results indicated that dispersoids precipitation reached the optimum condition after treatment at 400°Cfor 2–4 hours with a fine size and high number density, resulting in the highest hardness.INTRODUCTIONThe precipitation-hardening 6xxx aluminum alloys with major alloying elements of Mg and Si are one of the most widely used aluminum alloys for building and construction and automobile industries (Dinaharan & Murugan, 2012). In recent years, there have been increasing demands for aluminum structural components to be used at elevated temperatures (250–300°C) for different applications. However, the mechanical properties of 6xxx alloys at elevated temperature are typically reduced due to the rapid coarsening of precipitates at 250–300°C. It has been reported that the yield strength (YS) of AA6061 in the peak-aged condition drops from 276 MPa at room temperature to only 30 MPa at 315°C(Kaufman, 1999). Therefore, it is a key concern to improve the elevated-temperature properties of 6xxx alloys to expand their range of applications."

Jan 1, 2018

By X. -G. Chen, J. Qin, K. Liu, D. Racine

"Understanding the thermo-mechanical fatigue (TMF) behavior of materials plays a significant role in the safety design of critical components used in aerospace and automotive industries, such as engine blocks and cylinder heads, which undergo the cyclic change of temperature and stress. However, the cyclic changes of temperature, stress and strain make it difficult using the traditional testing methods to accurately simulate the TMF process. In the present work, the Gleeble® 3800 system was successfully applied to develop a reliable procedure to measure the TMF behavior of aluminum alloys. The modified setup together with the new designed program allows the Gleeble system to precisely simulate the cyclic profiles of temperature and mechanical strain. The novel procedure includes the calibration and verification of the TMF setup to ensure the test validity with Young’s modulus measurement, multi-cycle measurement of the thermal strain and zero stress adjustment followed by online monitoring the TMF cycles. The results of the TMF testing of an AA6061 alloy under cyclic temperatures (60–300°C) and various strain amplitudes (0.2–0.6%) were demonstrated. Its TMF behavior was characterized by the typical hysteresis loops and cyclic stress-strain response.INTRODUCTION The thermo-mechanical fatigue (TMF) behaviour becomes increasing important to evaluate the elevated-temperature properties of materials used as the critical components in automotive and aerospace industries, such as the gas turbines (Hu, Shi & Yang, 2016; Moverare, 2007; Segersäll et al., 2015) and engine blocks (Grieb, Christ & Plege, 2010; Javidani & Larouche, 2014). During the cycles of start-up and shutdown of the engines, these components undergo a complex change of loading. Meanwhile, a dramatic temperature gradient exists on the components due to the cooling system. Therefore, the cyclic changes of load and temperature can give rise to the TMF and may limit the use life of such components (Hu, Shi & Yang, 2016; Javidani & Larouche, 2014; Moverare, 2007). Hence, performing the TMF tests to precisely simulate the cyclic changes of load and temperature to understand the TMF behaviours of materials is playing a significant role in the safety design of these components. For TMF tests, two principal types of cycles are generally employed, including the in-phase (IP) cycle where the load and temperature are at the same phase (i.e. maximum load at highest temperature) and out-of-phase (OP) cycle where the maximum load is applied at minimum temperature (Kliemt, 2012; Miller, 2014). The most significant damage mechanisms in engine components are reported to be OP TMF cycles (Javidani & Larouche, 2014; Kliemt, 2012)."

Jan 1, 2018

By D. B. Mazzinghy, L. C. de R. Machado, H. Delboni, M. G. Bergerman

"The use of vertical stirred mills in the mining industry has increased remarkably over the past few decades, as a result of growing requirement for finer ore grinding. This equipment delivers higher energy efficiency in fine grinding operations when compared to conventional tubular mills. Methods for designing vertical stirred mills involve operational experience, pilot plants and bench tests. An important issue is that these tests require, at a laboratory scale, at least 10–20 kg of material, depending on its density, which is not available in many cases, particularly in the early stages of greenfield projects. For the regrind of flotation concentrates, several bench scale flotation cycles are required to generate such a sample. This paper describes the development of a laboratory jar mill test using a 6”x8” jar – smaller than that commonly used – based on the overall specific energy method, which requires significantly less mass compared with existing tests. The proposed test has proven to be more practical than tests normally used, requiring about a quarter of the mass, and also shows good adherence to industrial results for the studied iron ore processing plant. INTRODUCTION A significant demand for finer grinding has been noticed over the past few decades in several mining projects to achieve the mineral liberation required for the concentration of valuable minerals. However, the finer the product size, the greater the grinding energy consumption, resulting in an overall increase in operating costs, which may reach or even exceed 50% of the mineral processing cost (VIEIRA, PERES, 2013; DANIEL, LEWIS-GREY, 2011). Comminution technology can have a major impact on subsequent ore concentration stages (DANIEL, LEWIS-GREY, 2011; MARSDEN, 2009; NAPIER-MUNN, 2012; PEASE et al., 2010), which further strengthens the importance of proper technology and equipment selection. Adequate grinding circuit selection and design is thus a key aspect associated with mining projects."

Jan 1, 2018

By P. V. Malyarov

"This paper examines the grinding and wear processes in drum mills. A summary of the industry’s long-term experience with the proposed linings is presented. A method is proposed for assessing the efficiency of the grinding energy distribution between the successive stages. A case study is presented of grinding energy redistribution at Talnakh Concentrator by replacing spiral classifiers with a drum-type hydraulic screen. The problems of the kinetics of grinding processes in ball mills and semi-autogenous (SAG) mills are examined. It is demonstrated that in ball mills the feed particles are disintegrated by triaxial compression in the mill zones where discrete slippage of the charge occurs at major force interactions between the layers. Mechanism underlying increases in the specific energy consumption in grinding circuits based on SAG mills is shown.The problem of improving the throughput and reducing the specific energy consumption in mineral feed grinding is highly relevant because of the significant energy intensity. Up to 80% of the consumed energy is used to disintegrate ore fed into the drum mill. At all development stages of the drum mill grinding theory, the researchers have paid a great deal of attention to studying the patterns of the charge motion and the kinetics of the feed particles disintegration processes. In [1], it was shown that, due to the slippage between the charge layers being lifted, drum mills at concentrator plants operate in a mixed cascade and waterfall mode. A feature of the mixed mode is the toe zone, where the charge contacts the lining and the transition to a circular path takes place. Studies of the charge motion in the toe zone made it possible to develop a method for designing cross-sectional profiles of lining plates [2] for ball mill drums. The method is based on the principle of interaction between the balls and the lining, where the non-working rear surfaces follow the relative motion path of the balls before impacting the lining, while the working surfaces are orthogonal to the rear ones. Lining with the proposed profile provides contact with the charge and slippage-free transition to a circular path. This ensures an longer service life of the lining, a reduction in specific energy consumption, and an increase in the mill’s feed rate. The proposed method is applicable when designing lining plates of various materials. Steel liners with the proposed profile have been successfully operated [3] for more than 40 years at a number of projects in the industry."

Jan 1, 2018

By H. Staton, N. Michaelson

"INTRODUCTION Lundin Mining’s Eagle Operation, located in Marquette County, upper Michigan consists of a mine and concentrator that process a Ni-Cu-(PGE) ore. The mine itself is an underground operation and the ore is trucked from the Eagle mine site 66 miles to the Humboldt mill where both nickel and copper concentrates are produced. Operations began in 2014 and continued with an average production of approximately 23,000 tonnes of Ni and 20,000 tonnes of Cu per year for the first three years of operation. The Humboldt Mill, currently operated by Lundin Mining, processes the nickel/copper ore from Eagle Mine and performs the concentration through several stages of flotation. Originally built in 1954, the Humboldt Mill began operations as an Iron Ore processing facility, and was converted to a gold processing plant during the 1980s. Various groups owned the site after closure of the gold operation. Eagle purchased the Mill in 2008 and invested more than $280 million to clean up historic mine waste and refurbish the plant (see flowsheet in APPENDIX). This paper will overview the ramp-up of the operation, and discuss some specific areas that went well and some that could have gone better during the design phase. HIGH LEVEL DESIGN CRITERIA Coarse ore arrives from the mine and is stored in a building with a capacity of 10,000 tonnes. Ore is crushed in three stages to a final product size of 100% Passing 12mm. Crushed ore is conveyed to the mass flow fine ore bins, which have a live capacity of 3000 tonnes. Crushed ore is fed to two parallel 900 HP ball mills, charged with 3” high chrome grinding media, and ground, in closed circuit with hydrocyclones, to a p80 of 110 microns in the flotation feed. Soda ash is added to the mills based on process water hardness. Cyclone overflow passes to the bulk conditioner where Sodium Isopropyl Xanthate (SIPX) and Methyl Isobutyl Carbinol (MIBC) are added. The slurry is pumped to the rougher bank for bulk flotation. Rougher concentrate is fed to a 500HP vertically stirred regrind mill and is ground to a p80 of 50 microns, using 5/8” high chrome balls. Rougher tailings report to the tailings thickener. The regrind cyclone overflow is sent to the single stage cleaner bank followed by two scavenger banks. The cleaner concentrate is pumped to the copper-nickel separation circuit. Cleaner tailings report to the tailings thickener. In the copper-nickel separation circuit, the pH is raised to 11.5 and a copper concentrate is recovered from the bulk cleaner concentrate in two stages, namely the copper roughers and the copper cleaner columns. The concentrate from the copper flotation columns is the final copper concentrate. The tailings from the columns return to the head of the copper-nickel separation. The nickel concentrate is the copper rougher tailings stream."

Jan 1, 2018

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

"The morphology of pellet feed is known to influence several properties of iron ore pellets, including drop number, compression strength and reduction properties. The effect of grinding method on the particle size, specific surface area and particle shape of an iron ore concentrate has been studied. Grinding methods considered were ball mill and high pressure grinding rolls (HPGR). 5 different samples (Blaine= 1800, 1900, 2000, 2100 and 2200 cm2g-1) were used to compare the size, shape and specific surface of particles for each grinding methods. Particle size was meticulously examined by sieve analysis, laser sizing and image analysis. In samples ground by ball mill, it has been observed that the fraction of particles <10µm increases from 39% to 46% as the Blaine number increases from 1800 to 2200 cm2g-1. For HPGR samples, corresponding figures are 41% and 49% respectively. It is evident that for samples ground by HPGR, the fraction of fine particles is higher than that of those ground in the ball mill. To measure the specific surface area of particles, Blaine and BET were used. A higher real surface area was observed from HPGR treatment in comparison to ball mill grinding, provided by a higher porosity, cracks, roughness and new surfaces. Shape factor of particles was determined using three descriptors: circularity, roughness, and aspect ratio. It was also observed that particles produced by HPGR were more elongated, less circular, and rougher than those processed by the ball mill. 1. INTRODUCTION Particle size and shape are important parameters that can significantly affect mineral processing plants and pelletizing plant performances (Brozek and Surowiak, 2007). It has also been proposed that green pellet quality is directly related to the amount of fine particles in a pelletizing plant (Dwarapudi et al., 2008; Umadevi et al., 2008; Gul et al, 2014; Van der Meer, 2015). Particle size distribution and specific surface area (SSA) are also key factors that can control the quality of green and fired pellets. Processing circuits generally reduce the fines fraction to lower than the required specific surface area (SSA). It is therefore necessary to regrind concentrates to produce suitable pellet feed for further treatment in the balling and firing steps [1, 2]. Two main methods are used for re-grinding of concentrate; high pressure grinding rolls (HPGR) and ball mill. Given the different forces used to reduce size in these methods, it is expected the shape of particles will be different (Pourghahramani and Forssberg, 2005)."

Jan 1, 2018

By Duong Huu Hoang, Nathalie Kupka, Urs A. Peuker, Martin Rudolph

"The froth ability, froth stability and the froth structure are strong influences in flotation process i.e. on water recovery, bubble size, entrainment of gangue particle, flotation rate constants, grade and recovery. The labscale flotation of rich apatite ore with a high mass pull leads to significant changes in pulp and froth properties over time. The froth stability decreases with increasing the flotation time. These changes can be related to different solid contents, reagent concentration, froth heights and bubble size distributions. This study presents the results from froth studies and discussions on the particle size of fully liberated silicates and degree of entrainment based on automated mineralogy size-by-size analysis. The change of entrainment in a rich apatite ore batch flotation with time will describe more precisely by measuring froth properties using a Dynamic Foam Analyzer. It is concluded that the degree of entrainment is not only dependent on particle size but also the pulp density due to its effect on particle settling and also froth properties in varying resistance to particle drainage. Furthermore, entrainment models are applied to predict the effect of size, flotation time on entrainmentINTRODUCTIONFroth flotation belongs to the group of heterocoagulation separation techniques. Froth flotation is classically divided into two active zones, the pulp zone (where particle collection occurs) and the froth zone. A schematics drawing of the interaction between both zones is plotted in Figure 18 (Yianatos and Contreras, 2010). In froth flotation, the collision probability in the collection zone is governed by the physics of the process or hydrodynamics (Wills and Finch, 2016). The true flotation event in the pulp occurs when the hydrophobic valuable mineral particles collide with bubbles and formation of a stable particle-bubble aggregates moving upwards against gravity to the froth phase (Yianatos et al., 2009)."

Jan 1, 2018

By G. Dodbiba, T. Fujita, M. Kawata, S. Yamasaki, K. Mitsuhashi, J. Ponou, Y. Iwazaki, T. Atarashi

"The grade of copper ore and concentrate is recently decreasing and it will continues decrease further in the future. The effective liberation treatment for low grade copper ore and the removal of arsenic from copper concentrate is becoming even more important. In this work, the magnetic separation of copper concentrate by heat treatment and the flotation of low grade copper ore by microwave irradiation was studied. The heat treatment of copper minerals in the air atmosphere, the magnetization of most copper minerals increases and especially the magnetization of chalcopyrite shows the largest magnetization, after being heated at 500 oC. The wet HGMS of copper concentrate has been studied and the results have then been compared with the ones when calcined concentrate was used instead. The microwave treatment before ball milling increased the degree of liberation up to 100%, especially when compared with the case when only ball mill was applied to the as-received ore. The flotation of ground copper ore after microwave irradiation showed that the grade copper minerals such as chalcosite and bornite in froth part is much larger than that of tailing part.INTRODUCTION The copper has been used many kind of technological fields and will be more important for the future technology. The global copper production from mine is predicted as shown in Figure 1 (Northey, S. 2014). The copper production peak will be appeared in 2030 and the demand peaks in 2040. In the future the recycling of stocked copper and copper alloy will be necessary to satisfy the demand (Yoshimura, A. 2018). Changes in the grade of copper in copper concentrate, exported from several countries are shown in Figure 2. The copper grade in copper concentrate after mineral processing is gradually decreases every year and it is less than 30% nowadays. On the other hand, the copper ore grade change and prediction are shown in Figure 3. The grade of copper ore is also decreasing to less than 1% in 2010 (Northey, S. 2014). In the future the copper grade gradually decreases, reaching to less than 0.5% in 2080 and the energy to produce the copper metal will increase. The effective liberation treatment for low grade copper ore and the removal of arsenic from copper minerals become more important, nowadays. The microwave irradiation of copper ore for the liberation, energy etc. has been reported by several researchers (for example, Batchelor, A.R. 2017). The magnetization change of copper ore by heating has been reported to remove the arsenic (Sawada, M 2015). In this report, the magnetic separation of copper concentrate by heat treatment and the flotation of copper concentrate by microwave irradiation are discussed after the characteristics of secondary copper minerals are investigated by these treatments."

Jan 1, 2018

By Daniel Johansson, Markus Danielsson, Håkan Schunnesson

In sublevel caving, blasted material flows gravitationally into the drawpoint from above in a periodical manner. This type of flow behavior entails muck pile conditions that are variable along the course of extraction. The effect of this variability on the LHD (Load-Haul-Dump) operation in terms of loading efficiency and ability to undermine the blasted ring is not fully understood as of today. This paper presents results from a field test in LKABs Malmberget mine in Sweden, where the influence of fragmentation on the loading operation has been studied in detail. Drawpoint filming was conducted for extraction of two rings equivalent of roughly 10000 metric tons (~9842 long tons) of material each. The analysis includes fragmentation measurements, muck pile classification, and general estimations in terms of loadability. Further, an evaluation of LHD machines from two different manufacturers was conducted to identify and highlight differences. The results show that fragmentation, muck pile compactness, and flow characteristics are all interdependent. Flow disturbances and the subsequent loading of compacted fine material in the back of the ring have been identified as the main reason for occurring problems and prolonged digging times. However, the ability to sufficiently undermine the blasted ring has been identified to primarily depend on digging depth which is only observed to be high during flow disturbances. An absence of flow disturbances seem to promote high loading efficiency but simultaneously limit the maximum digging depth. A mid-range particle size distribution with a low amount of fines has proven beneficial for overall loading efficiency. The various LHDs employed showed significant variations in terms of ability to handle difficult loading situations (e.g. compactness, boulders, etc.).

Jan 1, 2018

By L. Alagha, F. Schott, M. B. Haya, Z. Xiao, K. C. Monyake

"Froth flotation is a process in which valuable minerals are separated from gangue minerals on the basis of surface wettabilities. It is a universally accepted process for the beneficiation of coal. The large amount of coal fines that have been generated from both mining and beneficiation processes has been reported as a chronic problem to both fine coal preparation and utilization as these fines contain a high amount of ash forming minerals. The current study investigated the potential application of Synthetic Bio-compatible Polymers as slime depressants in fine coal flotation for the possibility to enhance the combustible recovery and ash rejection. Raw coal samples containing 21% of ash-forming minerals were crushed, grinded and floated in the presence of Chitosan polymer. Flotation tests were carried out in D-12 Denver flotation cell with 1-Liter capacity. Flotation outcomes were studied as a function of polymer concentration. Box-Behnken factorial method was used for experimental design. Second order response functions were produced for ash% and combustible recovery. The results obtained from this study demonstrated positive influence of chitosan polymer on ash% and combustible recovery. Ash % was decreased by 3.32 % while an increase of 48.15 % in combustible recovery was observed when chitosan was introduced in the flotation process. INTRODUCTION Froth flotation is a widely used method of separating minerals by utilizing the difference between surface wettabilities [1], [2].Modern mechanized mining and ore handling operations produce large amounts of coal fines which in the past were not processed but discarded as waste[3]. Even though flotation is the best method of beneficiation for coal, it can be challenging in case of fine coals. In fine coals, slime coatings of colloidal mineral matter exist on the coal surface. These coatings render the coal hydrophilic, hence reducing flotation efficiency and recovery. Of late, different researches have been using biodegradable polymers to determine their feasibility in enhancing fine coal flotation efficiency[4].Naturally occurring and synthetic polymers, for example, polyacrylamide-based polymers, have been widely used in flotation as multifunctional reagents[5],[6],[7]. Hybrid polyacrylamide polymer has been successfully used as a depressant for ash forming minerals in fine coal flotation[3]. Recently, chitosan has been successfully used in flocculating quartz particles to produce faster settling rates of fine tailings [4]."

Jan 1, 2018

By J. E. Nesset

The past 50 years have been a golden era, not just for the CMP but also for the development and success of Canadian technologies in the field of mineral processing. The CMP has played a critical role of technology transfer agent, and the success of these technologies is also linked to the success of the CMP itself. The presentation will cover, in brief, the growth of the CMP from its origins as the Canadian Gold Metallurgists in 1964, with some 39 attendees, to the present day when the annual meeting sees 500 and more from a dozen countries. Also covered will be selected technology success stories from the 50th anniversary volume to be given to all delegates ‘Canadian Contributions to Mineral Processing Technology 1968-2018’. The volume itself highlights some 40 technologies that have been divided into five categories; process water treatment and minesite environment, technology innovations, innovations in operations, technology providers and university contributions. Some international perspectives will also be shared.

Jan 1, 2018

By Guanghua Ai, Xiong Huang, Huashan Yan, Ting Li, Tingsheng Qiu

"Cyanide tailings of gold and silver concentrates contain considerable quantities of copper-lead-zinc sulfide minerals that can be recovered. However, the strong inhibition effect of cyanide often makes it difficult to recover these sulfide minerals effectively. In this research, a sample of cyanide tailings was investigated based on the principles of process mineralogy; activating flotation tests were carried out for the target minerals in the tailings, and the activation mechanism of the activator and its influence on the target minerals were investigated by Fourier transform infrared spectroscopy (FTIR). Mixed flotation of copper and zinc was carried out using QJ-01, a combined agent containing sulfite, as the activator of copper and zinc minerals, and ammonium dibutyl dithiophosphate (ADD) and butyl xanthate (BX) as the combined collector. Copper concentrate was obtained from the mixed concentrate by using a combined inhibitor of sodium sulfide and zinc sulfate to inhibit the zinc mineral. Zinc concentrate was extracted from the copper tailings by using copper sulfate as the activator and BX as the collector. The flotation test yielded copper concentrate with a grade of 22.56% and recovery of 76.96%, and zinc concentrate with a grade of 42.56% and recovery of 82.29%, which shows that comprehensive recovery of the sulfide minerals – copper and zinc –from the cyanide tailings was realized. The FTIR analysis showed that CN- was chemisorbed on the surface of chalcopyrite and sphalerite following cyanide treatment, while the combined activator QJ-01 containing sulfite reduced CN- into SCN- and weakened the complexing ability of CN- with metal ions on the mineral surface, thus achieving a good activation effect on chalcopyrite and sphalerite. The results of this study can provide practical guidance in increasing the resource utilization ratio of cyanide tailings in gold mines, and thus contribute to alleviating environmental problems caused by stockpiling cyanide tailings. INTRODUCTION Cyanidation, the most widely used technology for extraction of gold, has several advantages such as high recovery, process maturity, low cost, etc. According to available data, the annual discharge of cyanide tailings from China's gold mines exceeds 20 million tons (Li et al., 2011). Lower grades of exploitable gold ore entail increased discharge of cyanide tailings. Huge quantities of cyanide tailings are regarded as waste and stored, resulting in significant wastage of land resources. Moreover, residual beneficiation reagents, cyanide ions, and heavy metal ions in cyanide tailings cause severe pollution of water and land (Laitos et al., 2013; Donato et al., 2007; Mudder and Botz, 2004). In addition, cyanide tailings often contain valuable elements such as gold, silver, copper, lead, zinc, sulfur, and iron, which, if not recycled, would result in considerable wastage of resources. Hence, it is imperative to study the reduction and safety of cyanide tailings, and the mineral resources present in them."

Jan 1, 2018

By Vincent A. Scovazzo

"The most significant study on the effects of longwall mining on gas and oil well integrity was completed by a consortium of coal and shale gas industry participants. A field study was conducted in 2013 and 2014 and is referred to by its location on Well Pad NV-35. The experiment site was located at the CONSOL Enlow Fork Mine in Washington County, Pennsylvania.The experiment was completed to verify John T. Boyd Company (BOYD) calculations and studies completed under contract by for the Pennsylvania Department of Environmental Protection Gas Well Pillar Study Update. The findings of the original study were presented by BOYD at the 32nd Conference, while numerical analysis of the Well Pad NV-35 field study was presented by Dr. Su at the 35th Conference.This paper addresses the findings of the experiment and how it confirmed the conclusions of the original study.INTRODUCTIONA field study was conducted in 2013 and 2014 by a consortium of coal and shale gas industry members to test the effects of longwall-induced ground movement on the stability and integrity of wells drilled through a gateroad abutment pillar. The project was initiated to test initial John T. Boyd Company (BOYD) findings of the Gas Well Pillar Study Update (Scovazzo and Moran, 2014), completed for Pennsylvania Department of Environmental Protection, Bureau of Oil and Gas Management (PDEP). Background and initial findings on this project were presented at the 32nd Conference (Scovazzo and Moran, 2012). The field work and numerical analysis were spearheaded by CONSOL Energy, Inc. (CONSOL) with participation by Chevron, EQT, Noble Energy, Range Resources, Marcellus Shale Coalition, and the Pennsylvania Coal Alliance.Dr. Wen H. Su of CONSOL was the leader of the field experiment with input from the participants. Dr. Su also completed numerical analysis of the results and model casing deformation. Analytical results were presented by Dr. Su at the 35th Conference (Su, 2017)."

Jan 1, 2018