Search Documents

By M. Muskat R. D. Wyckoff

The phenomenon called "water-coning" is that, observed in many oil wells, in which bottom water gradually and frequently sudderlly displaces a part or all of the oil production when a certain rather critical production rate from the well is exceeded. To follow in detail the process of the formation of a water cone as it breaks through the oil zone and enters the well bore is a problem so complex as to make a theoretical analysis practically impossible. However, an analytical treatment of the flow system before the water has broken through and during the time that it lies statically beneath the oil zone with an elevated or "coned" surface can be carried through under certain approximations. To present an analysis which shows the essential characteristics of the coning mechanism is the purpose of the present discussion. Physical Basis of Theory and Meaning of Approximations As will always be true for flow systems where true water-coning is at all possible, the water will be supposed to lie beneath the oil zone because of its density contrast with respect to the oil. In fact, tinder the usual field conditions, when the pay horizon is reasonably homogeneous, the water most frequently enters the well through the lower zones, but even when it enters from intermediate zones it may, in the later life of the well, displace the bottom layers of oil, thus resulting in a system wherein the oil is effectively floating on the water.

Jan 1, 1935

By S. J. Schofield

INTRODUCTION ONE of the greatest and most interesting problems of economic geology is to discover criteria bearing on the persistence of ore in depth. It is a question which is very much to the fore in connection with many of our important mines in British Columbia, and, as is to be expected, it is a most controversial one. The present paper, summarizing the views of the writers concerning the possibilities, in some of the mining districts of the Province, for the persistence of commercial ore to greater depths than have been, or are at present, mined, is offered as a basis for a general discussion on the subject and to call attention to the need for renewed study and research on the problem. Sooner or later-at some depth or other-individual ore-shoots become impoverished and bottom. In many mines where this has happened, either at the same or at a lower horizon, another ore-shoot, which had no surface outcrop, has been encountered and has continued downward until it, in turn, has pinched out. The Kolar (Mysore, India) gold field, for instance, presents interesting examples of this recurrence of ore-shoots at depth (1). For many years these mines have been under the management of Messrs. John Taylor and Sons. On more than one occasion they have persisted in sinking or drifting on barren quartz or along a narrow fracture for many hundreds of feet before values were again encountered. Their earliest experiment in such bold development took place at a depth comparable to that at which most mines in British Columbia are considered to be bottomed. In the past, is has been concluded that the ores in British Columbian mines do not go below approximately 2,000 feet, and to that depth only in a few instances. Consideration of the depth to which ores have been mined in the Province appears to support this view. The figures shown in the accompaning table have been gathered from various sources and are approximate.

Jan 1, 1935

Mining officials, as well as members of the Bureau of Mines staff, in their efforts to make mining safer are confronted from time to time pith complicated problems concerning solution of which there is a diversity of opinion. To reduce these differences of opinion as much as possible and to obtain a generally acceptable decision on any mine-safety question, the Director of the U.S. Bureau of Mines established the Mine Safety Board on June 1, 1924- *** to consider questions arising within any divisions of the Bureau that require a definition of tie Bureaus s collective opinion as to safety practices, safety devices, or safety methods for underground operations or open-pit mining. The approved2/decisions shall form the basis of teaching and policy for the Bureau.

Jan 1, 1935

By Albert McIntosh

One of the most interesting as well as important factors connected with the petroleum industry is the consumption of motor fuel. A few years ago we always spoke of "gasoline," but when natural gasoline and benzol became more important it seemed desirable to include all of these products in the petroleum statistics and so there was adopted the term "motor fuel," which embraces these three products in their entirety. Gasoline always included all stove and motor gasolines, high-grade naphthas, cleaning naphthas, solvents, varnishmakers' and painters' naphtha and gas-machine gasoline. "Motor fuel" includes all of these products also; therefore, technically the term "motor fuel" is incorrect, but as the total quantity of these non-motor naphthas is small their inclusion does not distort the results to any appreciable extent. When the Federal Oil Conservation Board appointed its first semiannual forecasting committee early in 1930 to project the demand for gasoline and crude oil into the year 1930, it was necessary for that committee to formulate a method of forecasting. It adopted the system in use by some of the oil companies at that time, of using automobiles and per-car consumption. Six months later the American Petroleum Institute also formed a committee for forecasting, which adopted the committee principle of asking each member to produce his own forecast of demand by any method he thought best and to give a full explanation to the committee. The result of the latter method was to get the benefit of as many different methods of forecasting demand as there were members. The writer does not recall any two members ever using exactly the same method. By studying the different forecasts and their methods, there evolved a composite opinion, which was presented to the industry as the committee's estimate. The same method has been followed by the American Petroleum Institute or Planning and Coordination Committee ever since.

Jan 1, 1935

By Maurice A. Roche

Introduction Most of the Flin Flon ore-body, like many others in northern Canada, was covered by water. The original discovery was made where the ore-body outcropped on a strip of land jutting out into Flin Flon lake. The outcrop could be traced for a distance of 600 feet across the strip of land, but disappeared under the lake on both sides of the peninsula. Following the discovery or location of the property, in 1915, and subsequent to its examination by the H.P. Whitney interests in 1925, an extensive diamond-drilling programme was completed, which proved the existence of an ore-body at least 2,600 feet long and 900 feet deep. In plan, the central part of the ore-body at surface attains an overall width of about 450 feet; including waste horses, and gradually becoming narrower to the south. To the north, it stretches out as a much narrower tongue. The main body is a solid sulphide ore containing gold, silver, copper, and zinc. Adjacent to, and on the footwall side of, the solid sulphide ore-body, there are considerable widths of talcy disseminated copper ore, particularly in the upper 300 feet of the deposit, where the maximum widths occur. The ore-body occurs in a greenstone area, the rock being quite hard on the hanging-wall side, with the footwall schisted, talcy, and much softer. The greater part of the ore-body was overlain by 12 to 15 feet of water and from 15 to 90 feet of mud and clay, this material requiring eventual removal, regardless of the system of mining adopted. The total of mud and clay overburden was estimated at 1,000,000 tons. After considerable study, it was decided to mine the upper 300 feet of the ore-body by open-pit methods; the balance of the ore to be recovered by underground mining . The present paper gives an account of the methods adopted in both operations, and of the problems encountered.

Jan 1, 1935

By Nagel, Theodore

USE of oxygen in metallurgical operations was investigated by a committee of unusually able engineers more than ten years ago. A record of their work appeared under the title "The Use of Oxygen or Oxygenated Air in Metallurgical and Allied Processes," Serial 2502, Report of Investigations, U. S. Bureau of Mines. Shortly thereafter the A.I.M.E. published "Use of Oxygenated Air in Metallurgical Operations," based on a symposium at the New York meeting, February 1, 924. Quoting from the Bureau of Mines report In view of the many recent developments in oxygen manufacture, and considering the increasing cost and decreasing quality of our raw materials, the Bureau of Mines has taken the matter of the application of oxygen or oxygenated air to the metallurgical centers for consideration and has appointed an advisory committee to study the problem.

Jan 1, 1935

By Donald Cummings

CERTAIN dusts are dangerous when inhaled, but most hazardous of all dusts are quartz or other forms of pure crystalline silica. The inhalation of dusts containing silica in combination with other elements gives rise to changes in the lung which differ from those produced by pure silica. As a generality, silicates are less dangerous than pure crystalline silica and vary greatly among themselves in harmfulness. Repeated analyses have shown that approximately 70 per cent of the total number of particles involved in any dust-producing operation are below 1 to 2 microns in diameter. (A micron is. approximately 1/25,000 in.) Similar studies of dusts recovered from silicotic lungs post mortem have demonstrated essentially the same size frequency distribu-tion, except that the upper limit of size retained in the air sacs is approxi-mately 10 microns. Experiments carried on by Gardner and the author have further demonstrated that greater changes were produced by a fixed weight of very fine quartz particles (2 to 3 microns and smaller) than by the same weight of slightly larger particles (8 to 10 microns). Any attempt to control a dust hazard should therefore be directed toward the removal from the working atmosphere of particles less than 10 microns in size, and particularly those below 3 microns. All industrial hygienists agree on this matter, but there remains considerable dispute as to the lower limit of particle size capable of causing injury. It has been gen-erally conceded, however, that particles of harmful dusts smaller than ¼ to ½ micron are not essentially concerned in the development of pulmonary fibrosis. This opinion is partly substantiated by the existence of large numbers of these small particles in practically all atmospheres that are, not associated with any known hazard. Such particles are so small that they have very little mass, fail to settle even in quiet air, and probably are not easily retained in the lung. Until further research proves that they are involved in the dangers provoked by the inhalation of certain dusts, engineers will generally agree that it is better to dis-regard them.

Jan 1, 1935

By Emory Kemler

The problem of determining the most desirable operating conditions of an oil-well pumping unit or rig front, the selection of the proper material and size of sucker rods, and the design of a pumping unit require that sucker-rod loads be known with a reasonable degree of accuracy. The segregation of rig losses, the proper selection and operation of prime mover and reduction unit, and the analysis of the operation of subsurface equipment require a knowledge of polished-rod horsepower. The investigation of such problems as the instantaneous stresses set up in a pull-rod line or backside crank installation when the well is suddenly hooked on, a study of such problems as the effect of anchoring the tubing on rod load, tubing stresses and rod horsepower, and an analysis of the effect of subsurface equipment on rod loads make it necessary to have a dynamometer that is rugged, which can follow the sudden changes in load without any lag or damping effect, which will record the load in its true position with respect to polished-rod movement, and which will give a card large enough to allow the desired effects to be measured accurately. The inadequacy of the spring or fluid-pressure type of dynamometers has been covered in detail1. The data given show that dynamometers of the spring or fluid-pressure type exert a damping action on the peak loads and the inertia and friction of their load-indicating mechanism introduces a phase lag in recording the load. A dynamometer of that type will not give the load in the correct amount and will not record it in its true position with respect to stroke or time. New Type of Dynamometer Fig. 1 shows a magnetic strain-gage type of dynamometer, to be described in this paper. The strain gage A is used for measuring the load in the polished rod, a washer B and knife edge C take care of initial misalignment and reduce bending in the compression tube of the strain gage. The complete instrument can be transported in the carrying case E.

Jan 1, 1935

By S. P. Lowe

Introduction In the following pages a general description is presented of the concentrator and cyanide plant of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, together with some account of the steps which have led to the adoption of the present practice. For an account of the preliminary test-work and pilot-mill operation, the reader is referred to a recent paper by R. E. Phelan on the History of Flin Flon Mine up to Construction (1). Additional notes may be found in a paper which the writer presented at the Annual Meeting of the Institute in 1930 (2). The first ore was crushed in the present plant on July 1st, 1930, and the first ball-mill was started one month later, on August 1st. Since that time, production has been continuous with the exception of one month lost during a strike in the summer of 1934. There have been no major changes in equipment or methods of treatment since the present plant was built, but many minor changes have contributed to the improvement in results obtained and to the increase in capacity to the large tonnage now being milled. The accompanying flow-sheets indicate the equipment used in the several plants, with the average life and repair cost. As originally built, the concentrator was to treat 3,000 tons per day, but the capacity has been increased to 4,400 tons. The methods adopted to make possible this increase in tonnage will be referred to below. It was the intention to produce two classes of ore: (1) a heavy sulphide, and (2) a disseminated ore. The mill was consequently divided into two sections, each adapted for most efficient treatment of one particular type of ore. However, it was soon found that it would be impossible to mine the two classes of ore separately, so it was decided to treat open-pit ore, which varies greatly in character, in the sulphide section, and underground ore, which is fairly constant, in the disseminated section. This segregation is still maintained.

Jan 1, 1935

By G. F. Cross

INTRODUCTION THE electrical system associated with the mining development of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, may be conveniently divided into three main parts, namely, the Island Falls power plant, the transmission line, and the distribution systems at the mine and metallurgical plants. For a description of the Island Falls power plant and the transmission line, the reader is referred to the paper, to be presented at this meeting, by R. W. Davis and M.F. Huffaker (1). The transmission line and sectionalizing combinations are shown diagrammatically in Figure 1. The present paper deals with the distribution systems at the Flin Flon mine and metallurgical plants. THE FLIN FLON DISTRIBUTION SYSTEM In the high-tension sub-station at Flin Flon, each incoming 110 kv. line is provided with manually operated, gang-type disconnecting switches. Each line is connected to Canadian General Electric type F.H.K. 39-60B-F.2 T.P.S.T. 110 kv. 400 amp. oil circuit breakers, each provided with M.K.4 centrifugal motor-operated closing mechanism. Gang-type disconnecting switches are installed on each side of incoming line breakers, and a complete ring bus system is formed through station tie breaker, which is' further provided with gang-type disconnecting switches on either side. The?bus tie breaker is of Canadian Westinghouse design, type G.22B, 110 kv., 400-amp., solenoid-operated. All three breakers are provided with bushing-type current transformers, and the two line breakers are further equipped with bushing-type potential devices. Oxide film lightning arresters (121 kv.) are installed on each incoming line and are located outside the station. Each line is further provided with interlocked gang-operated ground disconnecting switches. All disconnecting switches are mechanically connected to auxiliary switches, which provide pilot service to indicating lamps in the remote-control room, located in a separate building.

Jan 1, 1935

By Francis M. Rice

Before the world-wide depression, the primary purpose of most blast-furnace operators was to produce a maximum tonnage of pig iron per day for each furnace in blast. Some attention was paid to the conservation of labor and raw materials, but the idea was well established that low-cost pig iron was attainable only when each furnace was producing a high tonnage. After the depression had set in, the picture changed considerably. Each blast-furnace operator was forced to run his plant in a manner that best fitted the economical set-up of his company. A great deal of thought was expended on the different methods of operation, always with the idea of making each product in a way that would best serve his company financially. Because of this abnormal condition, the blast-furnace man was compelled to indulge in various practices of which many had been believed to be next to impossible up to that time. The ultimate purpose of these innovations was either one or a combination of the following: 1. To produce only enough pig iron for immediate consumption at a minimum cost. 2. To produce gas for boiler or mill use to supplant some higher priced fuel. 3. To consume the coke produced at the coke plant, which was often viewed as a byproduct. 4. To protect the cash position of the company. These conditions were met by diverse methods, some of which were: 1. Slow or decreased wind. In some instances the blast blown was held as low as 25 per cent of the normal volume. 2. Intermittent operation, in which the furnaces were shut down or "fanned" at frequent intervals.

Jan 1, 1935

By Edmund S. Leaver

The selection of a process for treating a gold ore is governed primarily by the characteristics of the ore under consideration. The form in which the gold occurs, its mode of association with other minerals, and the size and surface condition of the gold particles are important factors which influence materially the choice of procedure for recovering gold. A knowledge of these characteristics may be obtained by microscopic and chemical methods combined with experimental testing. Cyanidation and amalgamation, either alone or in conjunction with flotation and gravity methods, are peculiarly adapted to the treatment of gold ores, especially those of relatively low grade. Gold alloys readily with mercury provided both present clean surfaces. The presence of oils and grease, antimony and arsenic minerals, or soluble sulphides have a harmful effect. Very small, flaky particles of gold frequently are lost in amalgamation because of noncontact with the mercury. Fine gold in pyrite, or gold having rusty or contaminated surfaces, is often lost for the same reason. Grinding or some form of abrasion sometimes removes surface films of iron oxide or substances of a similar nature, and alkalies or other chemicals are used to remove grease. Gold is readily soluble in cyanide solution, and this method of treatment is particularly effective in the recovery of gold from the tailings resulting from other types of concentration procedure. Cyanide solutions must contact the gold to insure recovery, and the porosity of the ore treated and the fineness of grinding required are important governing factors. The use of lime in cyanidation is necessary to protect the cyanide, to precipitate undesirable substances, and to settle slimes. Certain substances in ores are harmful in cyanidation; chief among them are those that combine with cyanide, forming cyanides, and carbon which precipitates gold from solution. Arsenic and antimony are also harmful if present in sufficient quantity. These and other difficulties encountered in cyaniding certain ores often are overcome by roasting prior to leaching. Zinc dust is used almost universally for precipitating precious metals from cyanide solutions. The refining and melting of the product may be accomplished by oxidizing the zinc before melting it in graphite pots with fluxes, although sulphuric acid is now used largely to remove the zinc before melting. Straight cyanidation practice is being replaced by flotation as a major process, followed by cyanide leaching of the tailings, but amalgamation is still needed as a primary process for the recovery of coarse gold before either flotation or cyanidation.

Jan 1, 1935

Jan 1, 1935

By C. G. Williams

IN preparing this paper on Canadian mine taxation, there has been no attempt to detail the requirements of the various taxing bodies; but rather to consider the matter from the standpoint of its underlying principles and give a general idea of the methods adopted. I have added an Appendix setting forth the principal features of the various Acts, which should be used for general reference only, since new rulings alter minor details from time to time. In current legislation, many important points are left to the discretion of the Ministers and their deputies. We are, indeed, fortunate in having in Canada an able and conscientious body of permanent officials, who bring a sense of justice and courtesy to their work which is most commendable, and which has done much to simplify the working out of general problems. The production of metals may rightly be deemed a form of manufacture, but differs from the average manufacturing business in three important respects: (1) In its early stages, it is wholly speculative, since it is impossible to make any definite appraisal of value or possibilities. (2) The principal asset of any mine, i.e., the ore in the ground, is a wasting asset, and is irreplaceable. (3) Any additional burden by way of taxation cannot be passed on to the public but must be borne entirely by the producer. Having regard to the first of these differences, it is apparent that, since the risk of loss is great, the reward in case of success must be correspondingly great. This fact seems to be constantly overlooked by those who regard the all too few outstanding successes in Canadian mining history as fit prey for predatory legislation. As an illustration of the speculative nature of early mining development, let us consider the Province of Ontario-and I take this illustration simply because I am more familiar with conditions there, and not because I believe it differs greatly from any other province. From 1907 to 1933, 165,243 claims were staked and recorded, from which 43 mines were developed which paid one or more dividends. There was, of course, some duplication through re-staking; also, on some claims very little work was done, and most mines have more than one claim. But, since staking and recording cost real money and effort, each of these claims must have been considered to have had merit.

Jan 1, 1935

By Paul R. Martin, R. B. Kelly

The area comprising what is geographically termed "Central Texas" was somewhat less active in 1934 than in 1933. The year saw the completion of 182 dry holes and only 74 producing wells. Bexar, Williamson and Bastrop counties, with active fields such as Yturri-Southton, Byersville, North Dale and Cedar Creek contributed a majority of the new oil wells. Hilbig, in Bastrop County, 1933's most important discovery in the district, saw no development during the current year. New fields opened in 1934 were Byersville, a serpentine intrusion in Williamson County, and Manda, producing from similar material in Travis County. Like most of the other serpentine plugs, neither gives promise of covering a very large area. Other active counties were Bexar, Bastrop and Caldwell, although successful operations in each of them were limited to the old fields. The location of producing fields is shown on Fig. 1. New Fields Byersvil1e.—Late in 1933, Fritz Fuchs completed Zeischang No. 1, eight miles south of Taylor, Williamson County, for an initial production of 25 bbl. per day. The oil is 37" B6. A.P.I. gravity and is from Serpentine formation at approximately 900 ft. Additional drilling was carried on in 1934, and at the end of the year 18 producing wells had been completed, proving about 200 acres. Manda.—The Manda field, or Kimbro field as it is termed by some, received its first production Sept. 10, 1934, when the Humble Oil & Refining Co. completed No. 1 C. J. Peterson as an 8-bbl. oil well. The new field is near Littig, in eastern Travis County, and is about 15 miles northeast of Austin. Production is found in serpentine formation between 650 and 750 ft. The same company's No. 1 Buck Christian, second well in the field, flowed 190 bbl. per day through a ?-in choke. Although only a small area has been definitely proven it is expected that present drilling will provide extensions in several directions.

Jan 1, 1935

By A. S. Baillie

THE subject of taxes appears to engage our attention altogether too lightly. At least it would seem that, notwithstanding the increase in the cost of government, and its concomitant increased taxation, little constructive work is being done with a view to solving the problem of increased taxes. I believe that the inattention of the public generally to the subject of increased taxation is due largely to the fact that shareholders are not advised of the amount of taxes paid by industry. Were companies to advise their shareholders the amount of monies paid or payable out of each year's earnings for taxes in one form or another, and were such amounts compared with the amounts available for distribution to shareholders, the effect would be a general demand for more equitable taxation methods. While I am not unmindful of the burdens and inequities in taxation confronting industry generally, I believe that the mining industry in this Province does not fully appreciate the burden represented by the costs of taxation. My reason for this belief is based partly upon1the fact that no serious effort has so far been made to devise some means By which the mining industry in British Columbia might protect itself against the ever-increasing burden of taxation. In addition to this fact the widely diverse nature of mining in British Columbia makes the accumulation of comparable data a problem which, so far as I can ascertain, has never been attempted in a manner which would be authoritative. It should not be necessary to cite the effects of this burden upon any one mining company or upon any branch of the mining industry, such as coal mining, placer mining, base-metal mining, or the precious-metal mines. In my opinion, the operation of our mines by large corporations is conducive to the payment of taxes with much less protest than would be the case were the taxes being taken out of the earnings of just a few partners or a very few shareholders. We appear to be too unmindful of the taxes, paid by mining companies, of a kind that are not so prominently brought to our attention as are the taxes which are calculated upon the taxable income of the company at the end of its fiscal year. British Columbian mining companies pay many other taxes besides those which are calculated upon taxable income. Among these are school taxes, property taxes, gasoline taxes, mineral taxes, coal royalty, to say nothing of fuel-oil tax, sales tax, and excise taxes.

Jan 1, 1935

By A. B. Hooker

[Permissible electric cap lamps represent a workable balance between the amount of light needed and the various limiting conditions, such as the weight the miner can carry conveniently, cost of the lamp, including upkeep, and adequacy or practicability of the lamp as regards safety, mechanical strength, and general performance. Other things being equal, the coot desirable lamp is one that gives the greatest amount of useful light. Conversely, with a given amount of light the most desirable lamp is one that its the most efficient respecting weight, cost, and performance.]

Jan 1, 1935

By J. E. Ryan

General Description Due to the extreme cold weather experienced in Flin Flon during the winter months, thought and precaution were necessary in the design of the plant buildings. The machine shop, carpenter shop, drill shop, and coal plant buildings are similar in the building materials used in their construction. They are sided with two-inch shiplap, insulated with celotex and asbestos paper, and covered with corrugated iron on all side-walls. Roofing consists of 2 by 4 lumber on edge, laminated, and further covered by celotex and three-ply roofing. These buildings are heated by means of unit heaters. The heaters are primarily steam-heated radiators, through which the air of the buildings is circulated by electrically-driven fans. Our machine shop is located to the east of, but central to, the main operating buildings of the mine and plant, and is so connected by a net work of tracks as to be able to serve all portions of the entire plant conveniently. The building is divided into two bays, the main bay 53 ft. by 340 ft., and the east bay 24 ft. by 340 ft. The shop office and drafting room, a two-story annex 24 ft. by 30 ft., is located on the west side of the shop. The arrangement within the shop is such as to house conveniently the several departments, namely, heavy machine tool section, repair floor section, boiler shop heavy tool and floor section, blacksmith heavy tool and forge section, tool room, electric welding rooms, stock room, tin and copper shop, and electrical parts and armature winding and repair shop (see Figure 1). All the heavy tools, the repair floor section, and railway tracks are so located in the large open bay as to be fully serviced by an electrically operated 15-ton bridge crane, with a span of 50 feet and a travel the full length of the shop. A standard-gauge railway track, branched off the main line, penetrates the full depth of the building. This track lies along the extreme east side of the main bay, allowing easy entrance and movement of rolling stock and heavy machinery, loaded on standard flat-cars, to the repair floors in the main bay. Eight jib cranes, affixed to building columns, further facilitate the heavy repair work throughout the various shop divisions. Our light and heavy machine tools are standard equipment, not unlike tools used in mine, mill, and railway shops.

Jan 1, 1935

By G. D. Tranter

THE importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the -pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint .of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth .history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By F. B. Plummer

THE practice of introducing acid into oil wells to increase production of oil and gas has been in use since 1894, when it was first used in the Pennsylvania. oil fields30.? It is only since 1928 that it has been used to any extent in the Mid-Continent18. The process has proved successful in increasing production, at least temporarily, in depleted oil fields where the producing formation is highly calcareous and where water drive is not too pronounced. In the Zwolle field in Louisiana, where the producing horizon is a chalk, increases of 100 per cent have been recorded25. In north-central Texas, where the oil is produced from the Marble Falls limestone, equally pronounced increases have resulted3. The production also in some fields yielding oil from quartz sand cemented with calcite has been benefited. The evidence of actual increase in total recovery of oil, however, has been questioned by some engineers18. It has been pointed out that the results of the treatment of a well in a new district, where the process has never been tried out, can never be predicted with certainty, since other factors besides percentage of calcareous content: of the oil sand play a large part in determining the success of the method. Numerous articles have been published on acid treatment and on the effects of acid on limestone1-35, yet very little has been written con-cerning experimental work on the actual effect, of acid on capillary pores and larger oil-coated voids of oil sands. This is due partly to difficulties in duplicating field conditions in a laboratory and partly to the fact that the process has been carried out largely by contracting companies that have been unwilling to publish details of their results for fear of loss of business to competitors. The authors, using equipment developed to measure the radial permeability of oil-sand cores29, have developed a method of investigating the results of acid treatment which has enabled

Jan 1, 1935