Search Documents

By W. A. Cole, E. L. Derby, J. F. Wolff

Exploration of Lake Superior iron ores is done principally by drilling. The soft iron ores are churn drilled and the harder ores are diamond drilled. The churn drill used is the Mesabi type and its operation should be described as "water jetting." The drill rods are washed down by the combination action of the water jetting from the bit at the lower end of the rods and the churning motion given the line of rods. The water, which is forced down through the rods, comes up between the wash rods and the casing, bringing the choppings to the surface. It is caught in three or more barrels, each of which has a stoppered hole 8-10 in. from the bottom. These barrels are successively filled, allowed to settle, and drained to the hole, until the desired depth is drilled. The sediment from each barrel is transferred to a settling tub in which it is allowed to settle; the water is then drawn off and the wet sample is collected and dried. The number of barrels used depends on the character of the ore. For example, when drilling sandy ores, all the wash water is caught and settled for the proper length of time without refilling any of the barrels. Thus, the sediment held below the stoppered hole in any one barrel is not disturbed. The casing is kept as near the bottom of the hole as practicable to prevent the caving of the hole from jeopardizing the sample. While the casing is being driven down and the hole is being washed clean after casing, the return water is not run into the sample barrels. In exploratory work in the harder formations, where the diamond drill is used, the sample comprises both core and cuttings. The care given in handling and preserving the core depends on the importance that may be attached to certain characteristic strata in different formations. The following instructions for the care of core samples are issued by the Ogle-bay Norton Co. for diamond drill work done for them on the Gogebic Range of Michigan:

Jan 1, 1925

By C. H. Green

Recently two papers on the structure of eutectics were read before thc British Institute of Metals, one by F. L. Bradyl and the other by A. Portevin. 2 In the preparation of photomicrographs of laboratory specimens as illustrations for student work, and in connection with various researches, the writer has been working along the same line for some time and, therefore, was much interested in the results given, especially those of Portevin. He has correlated the information on the subject and has outlined a broad scientific basis for future work along this line. It is largely with the idea of adding something by way of illustration to the work already done that this paper is written. The eutectic is generally understood to mean the alloy having the lowest melting point of any alloy of the system, and in which the melt becomes supersaturated with reference to the two or more phases which separate out simultaneously or alternately. From the surface pattern, the eutectic means a structure with no primary crystals. It is not always easy to get the exact eutectic composition in making any alloy; in fact, a slight range in composition may be expected and some of the coarser particles may be richer in either of the composing metals. Even when chemical analysis shows the right composition, differences in density of the pure metals may cause segregation, or supercooling resulting from different crystallizing properties may give a surface pattern the appearance of being on one side of the eutectic point. However, the alloys on either side of the eutectic composition, showing primary crystals of one of the phases and the effect of the proeutectic form on the surface pattern of the eutectic make a very interesting study, which is slightly touched upon in this paper. The phases, or microconstituents, of a eutectic may be pure metals (Pb-Sb, Tl-Au), solid solutions (Cd-Zn), a pure metal and a solid solution (Ag-Sn), or a pure metal or solid solution with an intermetallic compound (Sb-Mg, Sb-Cu, As-Cu, Bi-Te, etc.).

Jan 1, 1925

By Fulton B. Flick

The micrography and macrography of aluminum and its alloys present certain difficulties. Many of the difficulties attendant on the micrography have been removed by methods developed during the past few years, notably those of E. H. Dix, Jr.1 The development of grain size in aluminum and its alloys may be equally troublesome, yet comparatively little detailed attention appears to have been given to it. Satisfactory reagents are available for the development of such structurcs in ferrous and most non-ferrous metals, but those applied to aluminum and its alloys, i. e., alcoholic or aqueous solutions of sodium hydroxide or hydrofluoric acid are not entirely satisfactory. Hanson and Arch-butt,2 in speaking of these two reagents, state that "These two reagents give fairly satisfactory results, but they sometimes produce badly tarnished surfaces from which the surface deposit is difficult to remove." It has been our experience that neither of these reagents is to be entirely relied on for developing structures suitable for study or photography. This means that when the etch fails to produce satisfactory results the specimen must be repolished, through the 000-paper at least, and then etched with another reagent. This procedure entails a considerable loss of time, and the final results may not be all that might be desired. However, the reagent to be described, although not a panacea for all etching troubles, has improved results so markedly that it is felt that it & worth offering as a grain-size etch generally applicable to aluminum and aluminum alloys. Czochralski3 in 1915 mentioned the application of a solution of 10 to 20 c. c. concentrated hydrofluoric acid in 100 c. c. absolute alcohol, etching in this reagent being followed by dipping in concentrated hydrochloric acid soliltion.

Jan 1, 1925

By K. W. Fritzsche

The prosperity of any nation depends, to a large extent, on its natural resources such as oil, coal, 'metal, timber, waterpower, and fertile soil. Each one of these resources forms the basis of a huge industry. The mining and smelting industry ranks among the first since it paves the way for a number of other industries. The mines and smelters provide a market for electric power, coal, timber, and agricultural products: other industries in turn provide a market for metals and non-metals. The real pioneering, however, is done by the prospector who goes into the wilderness to search for the ores from which the metals are to be extracted for the use of men. Prospecting is an interesting and fascinating occupation. There are many difficulties and hardships in the way but the lure of gold and the vision of finding an outcrop that may develop into a large bank account, within a reasonably short time, will urge the prospector forward. Thus, on the outskirts of this northern hemisphere hundreds of prospectors are searching and toiling and of whom nothing is known or heard until they reach civilization and announce a new discovery. Then a mad rush takes place and everybody who can afford to go will take a gamblers chance and plant stakes in the neighbourhood of the new discovery, or wherever an outcrop of mineralized rock can be found, with the hope of winning a fortune.

Jan 1, 1925

By Jacob W. Young

A casual reading of the geological literature extant to-day would give one the impression that carbon is an element which by some chance or another always existed at or near the surface of the earth, and was never of a magmatic origin. The carbonaceous matter in shales is said to be of vegetal derivation; petroleum is stated to have been derived from vegetable matter or from marine animal bodies; if carbon or bituminous matter is found in igneous rocks or associated with metallic ores, the statement is made that deeply buried carbonaceous sedimentaries were undoubtedly the source from which such carbon or bituminous matter was derived. This, I do not consider a reasonable or common sense view of the matter. Carbon is one of the elements of which the earth is composed. In the table giving the periodicity of the elements it comes sixth in the order of increasing atomic weights. It is an element formed like all the rest were formed, and must be as common to the interior of the earth as the rest of the eighty-odd elements so far discovered. The spectroscopic analysis of light from the sun, and the stars, shows the presence of carbon in the sun and in the colder stars. Thus with carbon, an element, found throughout the universe as well as on the earth, it is entirely reasonable to consider it as present in the interior of the earth with the other elements. Such being the case, the magmatic origin for the various forms of carbon in rocks and ores is a rational and logical conclusion. If but a small fraction of thought and effort was made along these lines, which is made in fostering the idea of the organic origin of the carbon found in the earth's crust, untold advances in this phase of geological science would result.

Jan 1, 1925

By C. C. Griggs

From its inception, a limestone quarry or mine should be under the direction of a capable engineer. Before it becomes a reality, he should outlinc the future results, plan the most economical methods for moving the materials and the most efficient equipment, and pilot the undertaking along the narrow pathway of success, avoiding the pitfalls of uneconomical production and the precipitous walls of scanty profits. Inspection of successful limestone properties shows that all have had difficult engineering problems, the solution of which have required keen engineering ability. In approaching a subject of this nature, it is logical to follow the progress of the limestone operation from its inception to the end, as reflecting the engineering required. There are four major divisions: Investigation, equipment, development, and operation. Investigation On the reliability of the engineer's estimates and the soundness of his judgment depend the success or failure of the enterprise. When one visits a prosperous concern, realizes that the limestone is of a constant chemical composition, sees the mechanical devices installed, and watches the output leave the plant in trains of railroad cars or fleets of vessels, he may overlook the fact that in the remote past this great creation was born in some man's brain and evolved through competent engineering. Many factors must be considered before a promoter could procure the money necessary to launch such an enterprise, for a conservative banker will only recommend a successful producer while the promoter must provide funds on his own and his engineer's judgment. An engineering investigation must be made preliminary to expenditure for actual operation, which, for a limestone deposit, would' naturally embrace such subjects as : ' Readily available. 1. Tonnage available........ Possibly available. Chemical analysis.

Jan 1, 1925

By R. W. Bowers

In order to hoist the ore according to grades, stope samples are taken. Three equidistant grooves are picked across the breast at right angles to the dip of the ore, the part removed being caught in the hand and then put into a small bag. When there is broken ore in the breast, the lines are continued down the pile and a small amount taken at intervals of the length of the sampler's pick handle. The quantity of sample from each breast will be between 2 and 3 Ib. If there are two grades of ore, bessemer and non-bessemer, there are two sets of brass checks for each chute, each check stamped with the number of the chute; one set of checks has the word "bessemer" and the other "non-bessemer." Before any ore is removed from the chutes, it is the duty of one man to see that the proper set of checks is at each chute in the mine. As each motor car is loaded, a check is attached to it. When the train reaches the shaft, the sample man removes the check on the first car, notes the grade, and directs the motorman to spot it over the proper pocket. The check is then hung on a hook with the number corresponding to the chute from which the ore came. The sample man throws a short rope with a knot in the end over the car and at the point where the knot falls a standard scoopful is taken. This is placed in a large bag that hangs directly under the hook containing the checks for that particular chute. These chute samples represent a check on the grading of the various contracts and by counting the tags a check is obtained on the miner's tally of the ore going into each chute; the total of the checks represents the hoist. During the stocking season, a standard scoopful is taken from each top tram car. This sample is taken in the same way as the chute samples at the plats underground. Top-of-car Samples These samples are taken by using a rope, preferably a clothesline, knotted each 18 in. of its length, and a hammer and a scoop. The standard scoop measures 31/2 by 21/4 by 11/4 in. and holds about 1/2 Ib. of ore. The rope, as applied to the usual railroad cars at the mine, is knotted into fifteen sections. It is placed diagonally over the car from

Jan 1, 1925

"The largest variety of asphalt and related bitumen deposits in this country is found in Utah. Utah is one of the few places in the world where the hydrocarbon minerals, gilsonite or uintaite, wurtzilite (trade name elaterite) and ozokerite are produced. These bitumens occur in an area embracing nearly 10,000 square miles in eastern Utah near the Colorado line. This area is largely in the western part of the Uintah basin. The bitumens are in the Tertiary horizon in the various divisions of the Eocene series.Gilsonite is an asphaltite derived from petroleum, wurtzilite is an asphaltic pyrobitu¬men derived from petroleum, and ozokerite is a native mineral wax resulting from the met-amorphosis of paraffinaceous petroleum.Gilsonite is produced by the Gilson Asphaltum Company, a subsidiary of the Bar¬ber Asphalt Company, at Watson, Utah. A narrow guage railroad, seventy miles in length and with a 7 1/2 percent grade over the Book Cliffs on Baxter Pass, was constructed by the company from the Denver & Rio Grande Western railroad main line in order to open up the gilsonite deposits. The veins range from narrow upward to 18 feet in width. The Rainbow vein at the present wokings is eight feet wide, vertical, and has sandstone walls. This vein has been opened up for a distance of about three miles and in some places four hundred feet deep. Forty men usually are employed with a production of eighty tons per day."

Jan 1, 1925

By Edward C. Jeffrey

The use of coke in metallurgy, to any important degree, dates from the middle of the 18th century. Its utilization came most opportunely for European civilization. The forests of Europe, except in the most remote and inaccessible regions, had been largely fed, in the form of charcoal, into the smelting furnaces. For a hundred years—the middle of the 17th to the middle of the 18th century—there .was a stationary condition of population corresponding to the exhaustion of European forests. This situation, which was particularly evident in Great Britain, was due to the fact that the forests had been depleted and the practical utilization of coke had not begun. The coking industry is essential for our metallurgical industries, which in turn are basal to healthy economic progress. But coke is of great importance, not only on its own account, but for its byproducts, which enter fundamentally into all the arts of peace and war. The dyestuff industry and the manufacture of explosives are intimately connected with one another, as was shown by the recent war. The subject of coking coal, therefore, is well worthy the serious attention both of practical industry and the scientific investigator. The most valuable coking coals, from the metallurgical standpoint, are derived from the coals of highest ranks. Coals, for example, that have a carbon ratio of from 70 to 80 per cent. yield the most valuable coke for the blast furnace. The difficulty of investigating these coals, however, is great, for they are rather friable and delicate and possess a high carbon content, which makes them difficult to manipulate. They present, on account of their high carbon content, a considerable degree of opacity when examined, in thin sections, under the microscope. The tenderness of structure and blackness of such high-grade coking coals as those of Connellsville and the Pocahontas region make them extremely difficult to investigate. Two of my colleagues, who are taking part in this discussion, will describe the valuable results that have been reached by studying coal by the methods of the mineralogist. Doctor White and Doctor Thiessen have studied the structure of coal as determined from thin sections that

Jan 1, 1925

By Heihachi Kamura

In this research, the proper temperature for the reduction of iron ores by carbon monoxide was determined. Also, the difference of the rate of reduction on the sizes of ore under four mesh per linear inch was estimated, but no evidence could be found. Rates of reduction on the seven kinds of ore were compared with the results of the experiment, showing a close relation between reducibility and density of ore. Finally, the maximum size of ore that can be reduced in applicable length of time was determined. The author thinks that the process of production of steel may be replaced by low-temperature reduction of iron ores some time in the future. THE reduction of iron oxide, such as Fe203, to iron in the blast furnace is performed principally by carbon monoxide, but partly by solid carbon by the two following reactions: Fe203 + 3CO = 2Fe + 3CO2 2Fe203 + 3C = 4Fe + 3CO2 It is known that reduction by carbon monoxide takes place at a much lower temperature than reduction by carbon and that the reducing action of carbon monoxide progresses to the inside of the ore in lump form by gaseous diffusion. In the reduction by carbon, however, the reducing action takes place only at the contact surface of the ore and carbon, so that the more complete the reduction by carbon monoxide, the more efficient is the operation. However, the reduction does not progress as shown in the foregoing formula, because carbon dioxide acts oxidizingly on the metallic iron to such a degree that when the gaseous composition reaches a certain proportion of carbon dioxide to carbon monoxide, the reduction practically stops, even though the gases are moving slowly through the heated ore. The proportions of carbon monoxide and carbon dioxide in the gas depend on the kind of iron oxide and the temperature of reduction, also the duration of time in the reaction. The longer the time of the reaction, the higher the proportion of carbon dioxide obtained in the gas, but finally it will attain to a condition of equilibrium.

Jan 1, 1925

By D. Harrington

During the past few years, there has been a trend toward the use of rock-dusting, rather than relying on humidifying, or the use of water, to limit or prevent explosions in the coal mines of the United States. This is partly because British coal mines have adopted rock-dusting and, at least in a sense, have condemned the use of water. Moreover, during the past few years, particularly in the latter part of 1922 and in 1923 and 1924, several explosions with heavy loss of life occurred in coal mines of the United States that were known to have more or less extended sprinkling, or humidifying, systems. The sentiment created by these disasters quickly caused a distrust of explosion-prevention methods requiring use of water and simultaneously caused more or less of a stampede into rock-dusting. Much of the wholesale condemnation of watering methods was without adequate knowledge, or at least without adequate consideration, of local conditions in each case, and rock-dusting was adopted largely without sufficient knowledge of how to rock dust safely or correctly. However, mines that had been using watering methods and had suffered these recent serious disasters (notably Dolomite, Dawson, and Castle Gate) instead of abandoning the use of water when operations were resumed after the disaster, greatly extended their watering systems. At the same time they took other precautions as to electricity, ventilation, blasting, etc., and supplemented the watering system with rock-dusting where the latter was likely to be the more effective. The trend toward rock-dusting during the past year or two (succeeding the recent mine disasters) is very similar to the rapid movement toward watering, or humidifying, methods, about 1910 to 1912, after a series of disastrous mine explosions. The Phelps-Dodge Corpn., which operates a large property at Daw-son, N. M., after an explosion in its No. 1 mine in February, 1923, decided that it is dangerous to have all its "explosion-prevention eggs in one basket" and so adopted what may now be termed the Western coalmine explosion-prevention system, in which both rock-dusting and watering are used, supplemented by other up-to-date mining methods and practices; such as exclusive use of modern electric safety lamps, with magnetically locked flame safety lamps for testing purposes; use of

Jan 1, 1925

By Frederic H. Lahee

The purpose of this paper is to demonstrate the similarity of the oil-producing structures in the Mexial fault zone, and to show how the apparently very irregular well logs in these fields may be use? for the practical interpretation of subsurface conditions. The Mexia oil field, in Limestone County, Tex. (Fig. 1) is closely associated with a fault that trends about 30" east of north and has a displacement of between 200 and 400 ft., with downthrow on the west. Minor slips accompany this major fault, some being roughly parallel to the main break while others are transverse to it. These faults belong to the so-called Mexia fault zone, a belt of fracturing that has been traced in its characteristic features southward to near Kosse, 15 miles south of Groesbeck, in southern Limestone County, and northward at least as far as the Trinity River at the eastern border of Navarro County, and possibly as far north as Hunt and Hopkins counties.2 The Balcones fauil zone, from 30 to 40 miles west of the Mexia fault zone, differs from the latter in that its principal displacement is a downthrow on the east. In this respect, it is exactly the opposite of the Mexia displacement. Between these two zones of major faulting lies a great down-dropped block, or graben, which is broken by numerous minor faults. Oil Fields Associated with Mexia Fault Zone When speaking of oil fields associated with the Mexia fault zone, we refer only to those now producing from the Woodbine sand. In this category belong the Mexia, Currie, Old Richland or Seay-Cranfill, Powell, and New Richland fields, named in the order of their discovery (see Fig. 1). Subsequent development may prove that the gas found in the Boyd Oil Co.'s Connor well, north of Kerens, is coming from another pool in the same fault zone.

Jan 1, 1925

By Carl R. Davis, J. L. Willey, S. E. T. Ewing

The first tube-mill on the Rand was put into operation in May. 1904, at the Glen Deep Mine. From that time onwards, tube-mills were added to various plants, although little was known regarding the capacity of a given tube-mill when working on banket ore. Within a few years, however, the so-called standard size (length of shell, 22 ft. 0 in.; diameter, 5 ft. 6 in.) was generally used until the last year or two. Practically the only exceptions were about 30 tube-mills having a length of 16 ft. and a diameter of 6 ft., and a few open-end mills of the roller-supported type. Most of the information obtained during the last 15 years has been obtained with mills of the standard dimensions. The adoption of the tube-mill as an accessory to the stamp mill was rapid; and where 3 tube-mills were working on the Rand at the end of 1904, 244 were in use seven years later.' By 1910, good practice provided 1 tube-mill for 20 stamps of 2000-lb. falling weight. The horsepower of the motors driving the tube-mills had increased from 80 to 100 and then to 125 at this date. Broadly speaking, current practice at that date aimed at a ha1 product of which 60 per cent. was suitable for sand treatment and 40 per cent. for slime. The sand grading was +60 mesh, 6 per cent.; +90 mesh, 25 per cent.; — 90 mesh, 69 per cent.; and the slime grading +200 mesh, 2 per cent.; —200 mesh, 98 per cent. It was recognized comparatively early that the tonnage of — 90-mesh product produced by a tube-mill per 24 hr. was a convenient measure of

Jan 1, 1925

TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen:-To a Board of Directors keeping in as close touch with all of the affairs under their care as do the Directors of the A. I. M. E., through their monthly meetings, a report of the year's progress is almost superfluous. ' To the members who read the monthly reports of the Board Meetings and of the various activities of the Institute as published each month, a yearly report cannot carry much fresh information; yet for both it may be well, as is the custom, to glance over the field of our activities during the past year, and to make an estimate for the year to come. The beginning of 1924 was not propitious for the members of the mining profession, though tonnage production for 1923 had been high and the gross value higher than for several years. The margin of profit had been narrow, prospecting and development were limited, and many of our members were unemployed or were working in other industries. Toward the end of the year, higher metal prices were in sight. Old-time optimism began to grow, and it now brightens the outlook for 1925. An excellent barometer of the prosperity of the industry, and that of the Institute, for they go hand in hand, is the work of our Employment Bureau. During the past few months, the percentage of our members for whom openings have been found has been increasing to a marked extent, and many members who had fallen in arrears are placing themselves in good standing. The number of new members joining has remained about as it was in 1922 and 1923. The Directors have reason to congratulate themselves on the interest maintained during a dull period, for it is not humanly possible to take a keen interest in the technology of an industry when our hands and minds are not actively engaged in it Now, with a much brighter outlook, we can look forward to a year of increasing prosperity for the industry and for the Institute.

Jan 1, 1925

By Heihachi Kamura

The reduction of iron oxide, such as Fe203, to iron in the blast furnace is performed principally by carbon monoxide, but partly by solid carbon by the two following reactions: Fe2O3 + 3CO = 2Fe 4- 3CO2 2Fe2O3 + 3C = 4Fe + 3CO2 It is known that reduction by carbon monoxide takes place at a much lower temperature than reduction by carbon and that the reducing action of earbon monoxide progresses to the inside of the ore in lump form by gaseous diffusion. In the reduction by carbon, however, the reducing action takes place only at the contact surface of the ore and carbon, so that the more complete the reduction by carbon monoxide, the more efficient is the operation. However, the reduction does not progress as shown in the foregoing equation, because carbon dioxide acts oxidizingly on the metallic iron to such a degree that when the gaseous composition reaches a certain proportion of carbon dioxide to carbon monoxide, the reduction practically stops, even though the gases are moving slowly through the heated ore. The proportions of carbon monoxide and carbon dioxide in the gas depend on the kind of iron oxide and the temperature of reduction, also on the duration of time in the reaction. The longer the time of the reaction, the higher the proportion of carbon dioxide obtained in the gas, but finally it will attain to a condition of equilibrium. Chemical Equilibrium of Iron, Oxygen, and Carbon Investigations concerning the equilibrium between iron, oxygen, and carbon have been carried out by E. Baur and A. Glaessner,1 who deter-

Jan 1, 1925

By E. J. Quinn, M. F. Fogler

In a recent paper, Rawdon and Mutchlerl gave some exceptionally interesting results on the Brinell and scratch hardness of severely cold-worked metals. In their work, they found that, on continued cold rolling, the metal hardened up to a particular point and then reversed and became softer; this was true for both Brinell and scratch hardness values. The generally reported behavior2 of metals, with respect to Brinell tests on cold-worked material, is that the metals harden up to a certain point and then, on further cold rolling, no change in Brinell hardness occurs. Jeffries and Archer3 state that there is little difference between the scratch hardness of annealed and cold-worked metals; the work of Faust and Tammann4 also indicated no difference between the hardness of annealed and cold-worked copper. Rawdon and Mutchler found, when they plotted the reduction ratio (initial thickness divided by thickness after rolling) against the hardness value for the cold-rolled material, that the hardness number increased up to a reduction ratio of about 3 and then decreased and became even smaller than that for the annealed metal. This behavior was reported for both scratch and Brinell hardness; Figs. 1 and 2 show their results for Brinell hardness on the metals for which they published data. This is an exceptionally interesting phenomenon, if it occurs under all conditions of rolling, and would have an important bearing on the practice of cold

Jan 1, 1925

By W. H. Schacht

The operations of the Copper Range Co. are located in the Michigan copper district at the southern end of the Keweenaw Peninsula, 8 miles southwest of Hough ton (the center of the district). All the producing mines are situated in a long narrow zone paralleling the peninsula and occupying the central portion. This zone is about 25 miles long and 3 to 4 miles wide. The important mines, in their order from northeast to southwest, are, Mohawk, Ahmeek, Allouez, North Kearsarge, Wolverine, South Kearsarge, Centennial, Calumet & Hecla, Osceola, Franklin, Quincy, Isle Royale, Baltic, Trimountain, and Champion; the last three are operated by the Copper Range Co. The existence of copper deposits in this district became known soon after the discovery of America. Many references by early explorers show that copper was found in the possession of many of the American Indians that inhabited the Great Lakes region. There is abundant evidence that exploration of these copper deposits extended into prehistoric times; and some indication that the American Indians carried on operations shortly before the advent of white men. An account of the finding of primitive mining appears in the Government publications of 1850-51 by Foster and Whitney. Although earlier expeditions by white men had been made to the Keweenaw peninsula, an attempt to commercialize the district was not made until after 1765, when Alex. Henry, a British subject, searched the shores of Lake Superior for mineral treasure. His first expedition took him to the Ontonagon River, where he found the famous mass of copper now on exhibition at Washington. In 1771, he started operations along this river with a crew financed by English capital; but after much difficulty and only meager success he found only detached masses while in search for a major deposit. There is no record of any cxploration from 1774 to 1820. In 1838, Dr. Douglas Houghton was appointed state geologist. Prior to that time he had made several visits to this region; and was the first white man to find

Jan 1, 1925

NAME "Utah" is derived from the name of the Indian tribe, variously spelled "Yuta," "Ute," "Youta." "Uta." "Eutaw," and finally "Utah." It means "in the tops of the mountains," or "on the heights." The state emblem is the "Beehive," typical of industry. State nickname is "Beehive State." AREA Utah is the tenth state in area. It contains 84.990 square miles, of which 2.806 miles are water. When admitted as a territory in 1850. Utah included all the area from the east line of California to the summit of the Rocky Mountains between the 37th and 42nd parallels, which embraced practically all of the present state of Nevada, all of western Colorado, part of Idaho and part of Wyoming, in addition to the present area of Utah.

Jan 1, 1925

By W. T. Thom

In previous classifications of coal, it has been customary to regard moisture eliminated from coal samples between 20 and 100 C. as extraneous matter, rather than as a constituent part of the coal. It seems, however, that the physical character and use properties of the low-rank coals are directly related to the amount of such moisture present, and recent chemical work has shown' that such coals contain unstable groupings which decompose between 20 C. and temperatures somewhat above 100" C., with the splitting off of moisture. According to this view, the moisture eliminated from air-dried coal below boiling point is similar in all essential respects to moisture eliminated above 100" C., and is produced by analogous reactions; and inasmuch as the moisture given off above 100" C. has always been treated as a constituent of the volatile matter of coal, it would seem that consistent usage would include as a part of the volatile matter all moisture present as an essential component of the coal as it occurs in nature. As a matter of experience, it seems clear that the general physical and chemical characteristics of the low-rank coals are largely determined by or related to the moisture, whether chemically or physically combined, present in air-dried coal; it is also demonstrable by trial that the low-rank coals cannot be satisfactorily classified on a purely chemical basis by using the moisture free form of analysis. The low-rank coals of the western United States include numerous well-defined types, many of which were referred to in a classification proposed by Ashley,2 in which the physical and use properties of the coals were made the primary basis for their systematic grouping. When testing this classification by replotting analyses of these type coals according to the Seyler scheme of classification,3 a satisfactory parallelism between use properties and chemical constitution of the dry coal was found among

Jan 1, 1925

By C. P. McCormack

The Cuyuna manganiferous iron ores can be a principal source of manganese for the iron and steel industry in the United States, provided metallurgical methods as a whole are adjusted so as to use run-of-mine ore. The use of manganese in steelmaking is growing. Increasing amounts of impurities in raw materials call for more manganese, a constant cheap supply of which is wanted. There are few deposits of ore in the United States carrying over 35 per cent. manganese that can be mined and marketed at a profit in normal times. We are largely dependent on foreign ores. The small domestic deposits should rightly be held in reserve for an emergency, such as a war, when importation might cease. Even the production from lean ores, concentrated it may be, might not carry us through a protracted stringency. The Cuyuna district is, therefore, during normal times capable of supplying a large total of manganese. The ores are iron ores containing 5 to 25 per cent. of manganese with the inverse range of 52 to 28 per cent, of iron. The manganese costs no more per unit in the ore than the iron, because cost of mining, largely by open-pit methods, is not affected by the manganese content. The manganese units should, perhaps, command a higher price, but as their value is contingent on metallurgical practice, a higher price may be justified only when a shortage in manganese occurs. Manganiferous iron ores can never entirely supplant straight manganese ores though methods are employed that will permit them to do so partly. For the manufacture of ferromanganese, ores carrying above 42 per cent. manganese are needed. Ores with manganese running between 20 and 42 per cent. are used for making spiegeleisen. But established practice in certain plants, based on the admixture of manganiferous iron ores to straight iron ores has greatly lessened the consumption of high-priced, scarce, manganese alloys with good results. The substitution of manganiferous ores for ferro and spiegel affects the manufacture of basic iron and its conversion into basic open-hearth

Jan 1, 1925