Search Documents

By Bruno Alves Resende

Em julho de 2010, a linha de Tiras a Quente da Usiminas, planta de Ipatinga, passou a operar com um novo sistema de controle para o laminador de acabamento. Assim, foi necessário atualizar o simulador offline de set up do Trem Acabador, utilizado frequentemente pelas áreas técnica e operacional. Para isso, toda a lógica de cálculo e formulações matemáticas do sistema online foram assimiladas e empregadas no novo simulador. Os resultados das simulações, quando comparados com os valores gerados pelo modelo online, mostraram-se bastante confiáveis. Sendo assim, conclui-se que o aplicativo desenvolvido está apto para ser utilizado como uma ferramenta de simulação offline do modelo de controle do Trem Acabador. Os benefícios potenciais do uso do simulador são: (i) aumento da produtividade por meio da redução de paradas da linha, (ii) melhoria da qualidade final do produto, (iii) redução do número de experimentos na produção e (iv) ajuste dos parâmetros dos modelos de controle. No presente trabalho são apresentadas e discutidas as características do desenvolvimento, da apresentação e da aplicação desse simulador.

Aug 17, 2017

By Mariana Carla Mendes Rodrigues

The present study deals with the effects of strain rate on the functional behavior of NiTi thin wires. The samples, in the austenitic condition at room temperature, were mechanically cycled 20 times by loading up to 6% strain followed by complete unloading, at 25°C. Four different quasi-static strain rates were assessed: 1x10-4, 1x10-3, 1x10-2 and 5x10-2s-1. The functional properties are described by means of critical stress to induce martensite, stress at maximum strain, energy dissipated per cycle and residual strain. The sensitivity of repeated cyclic deformation to strain rate is also analyzed in terms of phase stability. The results show that the fluctuation in the loading plateau, due to non-homogeneous transformation, increases with increasing strain rate. During cycling, it is observed that higher strain rates result in lower critical stress to induce martensite after the 5th cycle. However, the stress at maximum strain is higher at high strain rates, regardless the number of cycles. The accumulation of residual strain also increases with the strain rate due to the higher applied stress. During unloading, both the elastic deformation of stress-induced martensite and the reverse transformation seem to overlap at high strain rates. The dissipated energy behavior changes between the 1st and 20th cycle. No martensite is stabilized after training, but the intensity of the X-ray diffraction peaks of austenite increases with strain rate, as a result of stress relaxation.

Aug 17, 2017

By Douglas Glenn Stalheim

Production of structural hot strip coils in yield strengths up to 700 MPa and higher is increasing worldwide. In addition to requiring higher strengths, structural designs require good formability, toughness and weldability. Toughness and formability come from optimization of ductility properties while weldability comes from lower carbon equivalent alloy designs. The key to the production of optimized cost effective hot strip produced structural coils is to create the correct balance of a proper alloy/processing design to create as fine and uniformly distributed cross sectional grain size as possible. In addition to the creation of the fine/uniformly distributed cross sectional grain size, the correct microstructure needs to be created. In the higher yield strength grades, not only does the grain size/distribution play a role but a proper understanding and control of microalloying precipitation kinetics is required. This paper will present various examples of hot strip alloy designs to produce cost effective hot strip structural coil in yield strengths up to 700 MPa with good ductility and weldability. In addition, steelmaking/casting parameters will be discussed to assure successful production. Optimized reheating, rolling and cooling parameters of these alloy designs will be introduced in an accompanying paper.

Aug 17, 2017

By Yasser Ghobara

Phosphorus is a problematic impurity that has challenged steelmakers for decades. Steel producers have developed specific technologies to eliminate phosphorus prior to and during steelmaking. These process technologies reduce phosphorus to various degrees and increase the cost of making steel. The state-of-the art dephosphorization technologies are described and operating costs compared for each of the established technologies. Costs are discussed in terms of price penalties for high P iron ore and selling premiums for low P steel. From this, strategies to control P in a cost effective manner are described.

Aug 17, 2017

By João Paulo Meneguelli Campos

O objetivo deste trabalho foi validar o modelo proposto por Kasuya et al para prever as durezas máximas da zona termicamente afetada (ZTA) em juntas soldadas de um aço com médio teor de carbono através de ensaios empíricos. Para isto, se faz necessário o cálculo da energia de soldagem, quando foram testados modelos apresentados por Marques e Modenesi e também o modelo proposto por Perdigão. As juntas soldadas foram produzidas usando chapas de aço SAE 1045 com espessura de 12,7 mm como material base, chanfro de 70º e arame sólido do tipo ER70S-6. Para mudar as condições de resfriamento das juntas soldadas, foram testadas variações nos parâmetros de soldagem, tais como: energia de soldagem, taxa de resfriamento e temperaturas de pré-aquecimento e interpasses. Foram feitos experimentos com e sem pré-aquecimento e testados pós-aquecimento e alívio de tensões. As amostras da zona fundida e da ZTA tiveram as durezas medidas e foram analisadas por meio de microscopia eletrônica de varredura. Em linhas gerais, os resultados empíricos para a dureza na ZTA seguem a mesma tendência prevista pelo modelo de Kasuya et al, mas observam-se desvios na proporcionalidade validando a equação parcialmente para o material estudado. Também foi possível constatar que para o cálculo da energia de soldagem são adequados os modelos propostos por Perdigão e Marques e Modenesi.

Aug 17, 2017

By Ismar Antônio Sardinha

Usually outer straight steel tubes are used to blow supersonic oxygen into LD converters (BOF) to make liquid steel, although conical tubes are used too. Inner tube for oxygen blow and intermediary tube for water IN and water OUT are normally straight steel tubes. Present paper shows the influence of outer tube shape and metal used to in lance cooling and, consequently, a skull retention on lance surface. There are two parameters more important related to lance cooling: velocity of water out and the total lance cooling by addition of thermal conductivity of outer tube metal to it. For this comparison outer tubes are made of carbon steel or copper, and can be straight or conical. As related to velocity of water OUT, outer straight tubes have bigger efficiency than conical tubes. As related to total lance cooling, outer tube metal made of copper has much bigger efficiency than steel because of its thermal conductivity 7 to 12 times more depending on work temperature. The lance cooling has much bigger efficiency for the patented SKULLS3® technology with no skulls on the lance and no skulls into the mouth of LD converters (BOF).

Aug 17, 2017

By Maísa Villela Freire

Refratários MgO-C encontram-se entre os mais adequados para o uso na linha de escória de panelas para aço líquido. Seu comportamento, nesta aplicação, depende de fatores termodinâmicos e cinéticos. Métodos de cálculo termodinâmico para avaliar o potencial de degradação de refratários MgO-C por escórias e pela atmosfera são revistos brevemente. Tais métodos envolvem, em geral, premissas importantes sobre a quantidade de materiais envolvidos. Para avaliar um método mais simples, foram escolhidos dois tijolos MgO-C e duas escórias típicas do processo da CSN. Estes tijolos e escórias foram caraterizados, neste trabalho. O método apresentado consiste na realização de cálculos de equilíbrio em que a principal variável é a fração de escória em uma mistura hipotética com o refratário. Para a composição do refratário foram empregadas (a) composição média e (b) composição da matriz do tijolo. Os resultados indicam que é possível realizar previsões iniciais quanto à reatividade do refratário e determinada escória de forma simples. Os cálculos, evidentemente, não substituem testes cinéticos e testes em escala industrial, em vista da complexidade dos sistemas em questão.

Aug 17, 2017

By Camila Luzia Lira Duarte

O processo de pelotização utiliza o combustível sólido com intuito de gerar energia térmica que será transferida para a pelota de forma a alcançar uma queima uniforme. Na usina de Vargem Grande normalmente o antracito é utilizado como combustível sólido. Com objetivo de testar diferentes fontes de combustível sólido, um teste industrial de com coque breeze substituindo o antracito foi realizado. Como o coque breeze possui menor teor de matéria volátil, cinzas ei maior teor de carbono fixo, o consumo de gás natural no forno pôde ser reduzido. Além disto, o coque breeze apresentou um perfil de combustão mais favorável à qualidade da pelota resultando em ganho nos resultados de compressão. Dessa forma, a viabilidade econômica e operacional da substituição do antracito pelo coque breeze foi positiva.

Aug 17, 2017

By Jéssica Dornelas Silva

Diferentes mecanismos podem atuar e governar a deformação plástica de uma liga metálica. Estes mecanismos são fortemente dependentes de características como composição química, estrutura cristalina e energia de falha de empilhamento. Com o objetivo de se avaliar o comportamento do aço inoxidável duplex UNS S32304 quando submetido a esforços trativos e considerando a importância desta informação durante a conformação mecânica, este trabalho estudou a influência da taxa de deformação sobre as principais propriedades mecânicas medidas no ensaio de tração. Para a realização deste estudo, corpos de prova de tração foram usinados a partir de chapas do referido aço laminado a frio com espessura final de 2,5mm. Cada conjunto de 3 corpos de prova foi submetido às taxas de deformação de 7x10-4 s-1, 7x10-3 s-1 e 4x10-2 s-1. Por meio da análise dos resultados, observou-se uma diminuição na ductilidade e um aumento no limite de escoamento com o aumento da taxa de deformação. Entretanto, o limite de resistência não variou de forma significativa nas diferentes taxas estudadas.

Aug 17, 2017

By Theodore James Kurela

Analysis of adverse technical issues has traditionally relied on a snapshot of the state of the operation complemented with both the melt shop’s archived data and eyewitness accounts of adverse events. The GrafTech ArchiTech System is helping EAF shops solve problems faster by combining continuous analysis of information with statistically based alerts of process deviations. After one year of system implementation, a number of cases have been detected and communicated to melt shops worldwide. The objective of this paper is to examine a few of these cases; the early detection, statistical analysis, deviation reporting and the resulting countermeasures implemented.

Aug 17, 2017

By Breno Totti Maia

In the present paper, a new energy balance equation was developed, considering the slag phase, in order to define the effects of jet penetration and determine a new value for the factor K. The factor K measure the resistance to momentum transference between exit nozzle and metallic bath. The experiments were performed based on the same conditions of the article used as a comparison. The results showed the same behavior between the experiments and it was possible to determine a new value for the factor K, which changed from the unit order for the metal phase system to hundredths order for the metal and slag phase systems. These results are considered unprecedented.

Aug 17, 2017

By Cristiano José Scheuer

Experiments were carried out aiming to study the influence of micro-abrasive wear test variables and plasma treatment parameters, on the tribological characteristics of low-temperature plasma carburized AISI 420 steel. The first part of this study was conducted in order to evaluate the influence of abrasive particle size, normal load and counter body rotation speed on carburized sample wear behavior; and the second part was conducted in order to evaluate the treatment temperature and time effect on carburized samples wear behavior. Plasma carburizing treatments were performed at 8 and 12 h, for temperatures ranging from 350 to 500°C; and at constant temperatures of 400°C for times between 12 to 48h, and for 450°C for times of 4 to 16h. Micro-abrasive wear test were performed by mean of a calowear ball-cratering equipment using a polished ball of AISI 52100 steel rotating at 80, 120 and 160 rpm, for sliding distances from 2.6 to 104.2 m. Alumina abrasive particles with sizes of 0.05, 0.3 and 1.0 ?m were employed. The normal loads applied on this study were 0.1, 0.3 and 0.5 N. Carburized sample was characterized by mean of OM, XRD and hardness measurements. Worn crater characteristics were evaluated by confocal laser microscopy. Results showed that the transient wear regime prevails along the outer layer length (composed by Fe3C and ?’C), and the steady-state wear stabilizes in the diffusion layer region (composed by ?’C). It was verified that the wear rate and wear coefficient decreases with treatment temperature in the range of 350–450°C and increase for 500°C. It was also verified that the wear rate and wear coefficient decreases with treatment time in the range of 12–36 h (for 400°C cycle) and 4–12 h (for 450°C cycle), and increase for larger treatment times due the chromium carbide precipitation. It was also found that the wear coefficient increases with the increase of abrasive particle size, and decrease with the increase in counter body rotation speed and normal load. Lastly, the analysis of the worn craters indicates the occurrence of grooving and micro-rolling abrasion wear mechanisms.

Aug 17, 2017

By Alberto Pesamosca

The present work analyzes the latest results achieved in scrap based EAFs in terms of application of chemical energy, starting from the observation that the general trend is a reduction of oxygen utilization. Consequently a review is needed about criteria for evaluation of melting process efficiency and equipment design. If from one side the maximization of productivity remains one of the major goals, from the other side some aspects of present market situation, included price of raw materials, are requiring the maximization of process yield. Based on achieved performance figures of selected plants and theoretical considerations, the effect of chemical energy input intensity is analyzed focusing on transformation cost, productivity and total energy input. The effect of present practices with lower oxygen utilization is considered also in terms of global CO2 emissions. Finally, the latest Danieli concepts and technological tools for optimization of chemical input are presented.

Aug 17, 2017

By Silvio de Carvalho Sabença

Um forno a arco elétrico é um tipo de forno industrial que usa uma corrente elétrica alternada para produzir calor. Estes equipamentos servem como uma alternativa para os altos fornos tradicionais, e desempenham um papel importante na produção de aço. Em um forno de arco elétrico, a corrente elétrica passa através dos eletrodos de grafite, do aço e de outros metais, o que resulta na produção de aço de modo mais rápido e eficiente. A queda de tensão no arco é, praticamente, proporcional à distância entre o eletrodo e a carga. O eletrodo corresponde ao polo positivo (+) e a carga o negativo (-). Em corrente alternada os pólos, positivo e negativo, trocam de posição a cada meio ciclo da tensão de rede. Sob condições de arco, forma-se, no eletrodo e na carga, uma finíssima camada altamente ionizada devida a uma altíssima concentração do campo elétrico nestas zonas. No forno o arco se extingue quando a corrente se anula e reacende, quando a tensão volta a crescer. Devido a constantes quebra de eletrodo foi montado o grupo de trabalho com objetivo de reduzir o consumo dos eletrodos, otimização do consumo de energia, redução do Power On, aumento da potência média e redução nas quebras de eletrodos. Esta implantação foi extremamente importante pois o mesmo está garantindo a continuidade operacional, de forma segura e confiável, de um dos equipamentos mais importantes para a produção de aço na Usina.

Aug 17, 2017

By Robin Schott

The blast furnace process is the most important process to produce pig iron. The necessary process energy is mainly covered by coke. But the production of coke is connected with CO2-emissions and high costs. A significant measure to reduce the coke rate and with it the CO2-emissions plus costs is pulverized coal injection (PCI) through the tuyeres into the blast furnace. A further increase to substitute coke by coal can be achieved by using the Oxycoal+ technology. This article compares and shows the cost effectiveness and the decrease of CO2-emissions with the help of simplified energy balances for the only coke operation of the blast furnace, the operation using pulverized coal injection and the operation using the Oxycoal+ technology.

Aug 17, 2017

By Glaydson Simões dos Reisr

Micropore organosilicas (MOs) were synthesized using methyl-phenyl-polysiloxane as precursor. The MOs were characterized using several analytical and functional techniques. The materials were assigned as micropores materials, with specific surface area up to 642 m2 g-1 and yield up to 72.55%. The adsorbents have hydrophobic surfaces and were used for removal of diclofenac from aqueous solutions. The adsorption kinetic and isothermal data were well described by the general order and Sips models, respectively. Diclofenac exhibited a better affinity than NM and the mechanism of adsorption suggested that hydrophobic groups play a key role in the adsorption process.

Aug 17, 2017

By Konrad Krimpelstätter

The need for more effective and flexible roll-gap lubrication technologies in hot and cold rolling mills is steadily increasing due to ever-greater requirements placed on the rolling process and the final products. In particular, the rolling of high-strength steels poses enormous demands for both the rolling mill and the coolant/lubricant to be used. The presented paper focuses on two innovative technologies for highly efficient roll-gap lubrication for hot and cold rolling, which were developed utilizing extensive knowledge and expertise about the tribological interactions in the roll-gap. The advanced work-roll lubrication package (A-WRL) for hot rolling and ESP mills is using specially designed mixer-nozzle units to mix the water/oil emulsion very close to the nozzles to minimize the risk for contamination and clogging. The nozzles are quickly exchangeable and are optimized to ensure uniform lubricant distribution, high plateout efficiency and minimum oil consumption. This eco-friendly solution does not require any chemical additives or cleaning agents and significantly reduces electrical energy consumption and work-roll wear. The roll cooling system on mill entry and exit side remains switched-on, which is of vital importance especially for highperformance hot strip mills. Minimum Quantity Lubrication MQL® represents a new generation of roll-gap lubrication technologies for cold rolling, which applies minimum amounts of pure rolling oil finely atomized with pressurized air directly onto the work roll surface. This allows controlling the oil film thickness depending on actual process and product parameters, providing increased lubrication flexibility, significant improvement of strip surface cleanliness through reduction of strip wear. MQL® was successfully installed and tested on two industrial tandem cold rolling mills in Europe. Advanced WRL and MQL® represent Primetals’ latest technologies that feature a robust and reliable system comprising standardized interfaces and flexible communication options. Both packages can easily be integrated into existing or new hot strip mills, ESP lines or cold mills.

Aug 17, 2017

By Patrick Tassot

Increased worldwide highly competition in steel market imposes innovative measure for the steelmaker targeting cost reduction and climate-friendly steelmaking process in order to have the ability to withstand the pressure of the market. At the same time the demand for high purity and highest quality steels continues to grow from year to year, especially in the sector automotive in transportation of oil and gas, in the construction Industry and in the manufacture of heavy plate. As they allow producers to be up to the requirements while allowing expanding their product mix, new secondary metallurgical treatments have become a must additionally to standard equipment elements of steel plants modern. Most of these treatments occurs in the steel ladle increasing the pressure to ensure a reliable and as possible neutral reactor. Intelligent solutions for refractory lining ladles should integrate better adaptation to the operational process parameters and the high reliability/availability at the best cost/performance. This challenge has conducted Refratechnik to develop new concepts to overcome the frontier between shaped and unshaped materials and that’s what will be covered in this paper.

Aug 17, 2017

By Thomas Schanz

Current steel market conditions require small investments only to lower operational cost. SMS Concast has developed new products which optimize continuous casting process cost for long product steel production. This paper describes a selection of three products. All three systems are patented (patent pending for CONDRIVE). CONSAFE, a non-radioactive mould level measurement system for reliable mould level measuring on open stream casting CCM’s; CONSTIR-MWS, an improved control software for electromagnetic stirrers which lowers energy cost by 35%; CONDRIVE, a brand new oscillation drive system which provides the features of a hydraulic oscillator, however with a cost efficient electric drive.

Aug 17, 2017

By Milson de Andrade Júnior

A Central Termoelétrica número 2 (CTE#2) possui três caldeiras de alta pressão que utilizam principalmente os combustíveis residuais dos processos siderúrgicos, com destaque para o gás de alto-forno (GAF), o qual está disponível em grande volume e com baixo custo. Como o GAF possui baixo valor calorífico, ele é enriquecido em duas misturadoras com gás de aciaria (GLD) e na ausência ou limitação deste, com gás natural (GN). A partir de 2014, devido a problemas com o gasômetro de GLD, passou-se a utilizar o GN com frequência para fazer o enriquecimento do GAF, o que gerava significativo impacto no custo do vapor devido o alto custo do GN. O sistema de injeção de GN nas misturadoras era controlado de forma manual e praticamente não acompanhava as variações no poder calorífico (PCI) do GAF. Percebeu-se que seria possível implementar um sistema de controle para as injeções que levasse em consideração o PCI do GAF, reduzindo o consumo de GN quando o PCI estivesse mais alto e aumentando o consumo quando o PCI estivesse mais baixo. Após a implementação deste sistema houve uma significativa redução no consumo médio de gás natural para enriquecimento do gás de alto-forno na CTE#2.

Aug 17, 2017