Search Documents

By Ruixuan Zhang, Yan Li, Shusen Cheng

The measurement of raceway temperature in the blast furnace is a critical issue, which is very significant for judgment of, prediction and diagnosis of the racewa yburning state. This paper deals with mathematical models by Monte Carlo method to approximately simulate the radiation heat transfer in the race-way and establish matrix equations using CCD cameras, which are solved to obtain the three-dimensional temperature field. Due to the existence of fluctuation error, CCD camera measurement error and others,this is analyzed and random error is added in the measurement data to demonstrate the effectiveness and stability of the reconstructed temperature field. The results show that the reconstructed three-dimensional temperature field of the raceway is very close to the exact temperature.

Mar 1, 2017

By R. Padilla, I. Gonzalez, M. C. Ruiz, J. Salgado

The mining companies in Chile are increasingly using chloride salts and/or sea water in the sulfuric acid leaching of copper minerals. For this reason, the effect of chloride ions on the solvent extraction equilibria was investigated. Copper extraction isotherms were determined at 25 and 35 °C for aqueous solutions containing 6 g/l of Cu, 7 g/l of Fe, chloride ion concentrations of 0, 60 and 110 g/l, and a pH of 2.0. The organic phases were 20% v/v solutions of a ketoxime (LIX 84-IC) or a salicylaldoxime (LIX 860 N-IC). It was determined that the presence of chloride in the aqueous solution had a large negative effect on the extraction equilibria for both extractants, particularly the ketoxime. Therefore, as the chloride ion concentration increases, an efficient use of the extractant would become more difficult. An increase in the temperature from 25 to 35 °C positively affected the extraction equilibria for these extractants.

Mar 1, 2017

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Solange Kazue Utimura, Amilton Barbosa Botelho, Carlos Gonzalo Alvarez Rosario

In this study, the recycling of waste materials is interesting in the environmental aspect to reduce the amount of waste in land fill and attenuate the pollution of groundwater, air and soil due to the liberation of dangerous elements. Recycling materials is an important issue once it represents a potential source of valuable metals. Waste printed wired boards (PWBs) as a principal part of Waste Electrical and Electronic Equipment (WEEE) and it is a fast growing stream with complex composition. The composite materials from PWBs are ceramic, polymers and metals. Biohydrometallurgical route may offer possibilities to recycle PWBs from discarded computers with the order to recover copper. The extraction of copper from PWBs by bioleaching processeswas studied using a mixed culture of acidophilic bacteria fromacid mine drainage (AMD) and the bacteria Acidithiobacillus ferrooxidans (A. ferrooxidans). The bioleaching experiments were performed in shaker flasks at temperature 30 °C and 170 rpmwith 10% (v/v) inoculum and pulp density of 35 g/L. Themetals concentration was determined by energy dispersiveX-ray Fluorescence (XRF). The results showed that the maximum copper recovery from PWBs using A. ferrooxidans was approximately 89% and with a mixed culture of bacteria from AMD the copper recovery was 92%.

Mar 1, 2017

By Hong Li, Chenxiao Li, Wenwen Mao, Hua Lu

Directly charging limestone into slag in BOF is a newly emerging technique which broke through the traditional BOF slagging principle. It is necessary to study the decomposition behavior of limestone in converter slag during BOF steelmaking. FeOx, SiO2, MnOx and pre-melting slags were mixed with limestone according to different quality proportion to simulate the environment of limestone in converter slag. TG-DTA results indicated that slag with individual component, including FeOx, SiO2 and MnOx, all had obvious effects on reducing the decomposition temperature of limestone. Pre-melting slags with multiple components had further reducing effects than individual component. XRD results showed converter slag component would react with decomposition product of CaCO3 and generate solid solution or oxide, reducing the activity of CaO and the decomposition temperature of CaCO3.

Mar 1, 2017

By Bingguo Liu, PENG LIU, Haigang Dong, Jinhui Peng, Libo Zhang

Parameters of technique to decarburize from spent petrochemical catalysts via microwave oxidation roasting were investigated. Decarburization process was performed on a microwave heating system. The results showed that the decarburization percentage of spent petrochemical catalysts was significantly affected by roasting temperature and sample thickness in the range studied. The decarburization percentage was 99.5% in microwave fields under the optimized conditions, roasting temperature 600 °C, roasting time 40 min and sample thickness 2 cm respectively. The residuum after microwave decarburization was characterized by field emission scanning electron microscopy (FE-SEM) which showed that the deposit carbon had been removed effectively.

Mar 1, 2017

By Dachun Liu, Lei Shi, Yongnian Dai, Bin Yang, Yang Tian, Tao Qu

The carbonthermal reduction of high Mg–Si nickel laterite was studied under vacuum. The effects of adding calcium oxide and the reducing agent on the reduction of silicon in residue were studied at pressures of 10–200 Pa and different temperatures, with varying proportions of carbon and CaO. The analysis of the residue was performed using X-ray diffraction and chemical composition analysis. The results show the following: At 1350 °C with a C/O ratio of 1.5:1, the recovery of Si reached a maximum 71.09%. Under these conditions, Si exists mainly in the forms of Fe3Si, Fe2Si, FeSi and SiC. The recovery of Si was above 80% when the temperature was 1450 °C, the C/O ratio 1:1, and 15% addition of CaO. When CaO addition was 22.61%, all of the solid phase was Ca2SiO4.

Mar 1, 2017

By N. Bat, N. Sarantsatsral

Blasthole sampling practices were investigated at the Erdenet copper and molybdenum mine in Mongolia to address grade reconciliation issues. The goal of the study was to determine if the particle size distribution (PSD) of blasthole cuttings was accurately reflected in the samples. The study additionally examined if the measured grade was related to the particle size of samples. Using a sector sampler specifically designed to collect samples for the study, six large samples were collected from three blocks following a specialized protocol. Each sample was split into nine size fractions, ranging from larger than 12 mm to smaller than 63 µm. Copper and molybdenum grades were determined for each of the size fractions. For comparison, nine samples were collected from the same blocks following the standard mine sampling protocol. These samples were also split into the same nine size fractions. As with the other samples, grades were determined for each of the size fractions. The results showed that the PSD in the samples collected following the standard operating procedure varied significantly from sample to sample. This variation was much lower for the samples collected following the specialized protocol. Loss of fines was also indicated in the standard mine sampling process. These observations suggest that the standard sampling protocol did not consistently capture the PSD. The copper and molybdenum grades increased as particle size decreased, regardless of the sampling protocol used. This observation underscores the importance of the PSD of a sample being representative of the true PSD. Given the low number of samples in the study, it is not a strong conclusion that the standard sampling protocol captures the PSD inconsistently. However, it could be taken as a caution. On the other hand, the grade versus PSD relationship is more certain, given that it was observed regardless of the sampling method used.

Feb 1, 2017

By R. E. Vivas, J. A. Villa

"Located in the state of Colima, Peña Colorada is one of the largest iron ore operations in Mexico. The project is owned in equal parts by ArcelorMittal and Ternium. Though boasting a production capacity of 4.1 Mt/a (4.5 million stpy) of concentrate per year, Peña Colorada is faced with declining ore grades. In order to respond to this situation, Peña Colorada had to expand production even further. This expansion created various challenges that were overcome by the adoption and application of new technology. Examples of these technological innovations are discussed in detail in this article and include improvements in geo-modeling, mine planning, and mine operations. The successful implementation of these technologies paid for itself many times over, and has led to significant improvements in production and performance, while lowering the operating costs and reducing the variance between planning and execution.Project overviewPeña Colorada is a mining company that produces about 30 percent of the iron ore in Mexico. This project generates about 1,200 direct jobs and 3,000 indirect jobs, making a significant contribution to the local economy. Similarly, Peña Colorada invests in its local communities through numerous educational programs, scholarships, university agreements, social development, environmental agreements, etc. Peña Colorada’s operations consist of an open pit mine located in Minatitlán and a pellet plant located in the port city of Manzanillo, as shown in Fig. 1. Technological innovationsMost mining projects around the world typically follow the logic of “mining the next best ore.” Consequently, head grades tend to decline over the life of the mine. In the case of Peña Colorada, a decline in head grade combined with a decline in iron ore prices forced the operation to adapt to a new business environment and adopt new technologies to face these challenges. However, the first step along this process was to increase the confidence and reliability of the resource model. This task involved additional drillhole campaigns coupled with more detailed modeling techniques. Once the block model was completed, new optimization studies and production schedules were evaluated with new optimization tools that improved many aspects of the mine plan. The Peña Colorada block model has undergone 3 expansions to reflect additional information not available in the past. The model has expanded to the East and Southwest. The latest model expansion increased the total number of benches to 98 as a result of positive exploration results. Similarly, new geotechnical studies were prepared, which provided new guidelines for pit slope design, and new technology was implemented to monitor ground movement and slope stability. Two sectional block model views in Hexagon Mining’s MineSight 3D, along with the pit designs and geologic solids are shown in Fig. 2."

Feb 1, 2017

By A. Noble

"Froth flotation circuits are widely used throughout the mineral processing industry for the concentration of fine particles. It had been estimated that nearly 2 Gt (2.2 billion st) of ores are treated globally each year using this versatile separation process (Fuerstenau, 1999). Due to the high feed tonnage, a large economic incentive exists for flotation plant operators to optimize the performance of this critical processing circuit. Prior to the 1950s, the optimization of flotation circuits primarily involved the manual adjustment of operating variables based on visual observation and sporadic sampling (Lynch, Harbort and Nelson, 2010). During the next several decades, however, the advent of improved on-line instrumentation coupled with the rapid development of high-speed microprocessors allowed the industry to develop more advanced control systems that could quickly adjust operational parameters in response to disturbances in ore characteristics and plant flows. These early online controls typically involved feedback loops designed to stabilize cell performance through the automatic manipulation of process variables such as pulp levels, gas rates and chemical dosages. The set-points for these controllers were often set by plant operators based on one or more operator objectives, such as maximizing throughput, recovery or grade. More recently, these regulatory controllers have been interfaced with high-level data display and management systems that provide operators with the ability to better optimize flotation plant performance based on mathematical models and rule-based algorithms (Greet, 2010).While tremendous strides have been made during the past several decades, even the most modern flotation plants are still faced with the long-standing question: “What are we trying to optimize?” From an operator perspective, some common responses include “Maximize tonnage of saleable concentrate” or “Maximize metals recovery at a customer-specified market grade.” These replies may or may not reflect those of management, who often focus on economic goals such as “Maximize profits for each operational unit” or “Maximize rate of return for all corporate assets.” Unfortunately, these high-level objective statements do not always translate well into practice due to the disconnect between plant operating protocols and product value. Attempts have been made by industry to overcome this issue using various types of optimization routines such as linear programming or other optimization engines. While this approach does have some merit, these blind routines require considerable input data and interpretational expertise and provide little or no fundamental insight that can be used to drive improvements in concentrator performance."

Feb 1, 2017

"Iron ore is the source of primary iron for the world’s iron and steel industries. Its production can be reported as crude ore, usable ore or iron content of ore. Historically, the U.S. Geological Survey (USGS) used reported crude ore production from China in tabulations of world iron ore production while other countries have typically reported their production in terms of usable iron ore. When China’s crude ore production was tabulated with usable ore production from other countries, world iron ore production totals have been overestimated by 10 percent to a high of content and may include products such as concentrates, direct-shipping ore, pellets, and sinter.• Iron content, also referred to as metal content or grade, denotes the amount of elemental iron in the crude or usable ore.BackgroundIron ores consumed in the steel industry typically require an iron content greater than 58 percent before being considered commercially usable. Iron ores that are not commercially usable must undergo beneficiation to raise the iron content. Approximately 98 percent of the world’s usable iron ore production is consumed in blast furnaces to make pig iron, which is further processed to make steel.High-grade iron ore mines can supply usable iron ore, known as direct-shipping ore, to blast furnaces, with minimal physical processing and no beneficiation. With direct-shipping ore, the reported production for crude ore and usable ore are the same. Ore from low-grade deposits must undergo beneficiation to increase the iron content before it can be used by the steel industry. In this instance, the mined material is called crude ore and post-beneficiation concentrates are called usable ore; the amount produced will be less than the crude ore amount. With the notable exceptions of countries such as Australia and Brazil, most of the world’s iron ore deposits are low-grade and require beneficiation."

Feb 1, 2017

By Chee Theng

"Keep calm and carry on mining. That has long been the conventional wisdom in the mining industry, a largely cyclical one that has weathered roller-coaster booms and busts. But in the years from 2002 to 2016, an unprecedented steep rise in commodities prices that lasted a decade and then took a sharp turn downward had made it hard for gold and silver miners to stay the course.“The last 15 years highlighted some of the structural and inherent challenges that our industry has, from product price uncertainty to long lead times to the capital intensity of our business,” said Mitchell Krebs, president and chief executive officer of Coeur Mining, who was the luncheon speaker at the American Exploration & Mining Association’s 122nd Annual Meeting held Dec. 5-9, 2016, in Reno, NV.Looking back, Krebs said, “We were given this enormous gift of a commodities super cycle, and the industry kind of blew the opportunity.” While gold prices rose 319 percent and silver prices rose more than 200 percent over the 2002 to 2016 period, the XAU index of 30 gold and silver mining companies’ stock prices went up by only 20 percent.Entering 2016, precious-metals prices have made a comeback, with gold rallying strongly from a six-year low at the start of the year. This time, the industry is ready. Companies are leaner and meaner, with lower costs, reduced debt and an increased focus on higher grades and quality ounces. Although opportunities were missed in the past, the industry has got its act together and is now well positioned to take advantage of a price upswing and even to show profits when prices fall, as they did in August 2016, pushed down by a strong dollar."

Feb 1, 2017

By Chee Theng

"In 2013, Coeur Mining had more than $55 million in general and administrative (G&A) costs and less than $100 million in cash flow. This year, its G&A costs stand at $30 million, down by more than 40 percent, its all-in sustaining costs have shrunk by more than 30 percent, and its cash flow is above $200 million. To realize this, the company aggressively reduced both its corporate overhead cost and operating cost and repaid more than $300 million in debt.The more robust balance sheet meant the precious-metals producer was well positioned to reap the rewards of an upsurge in commodity prices in the early part of 2016. Its stock price soared from $1.75 in January to $15.98 in August. Although the stock price has since dropped to around $9 due to a stronger dollar and a more hawkish Federal Reserve that recently raised U.S. interest rates, shifting the opportunity-cost argument away from buying gold and silver, Coeur remains attractive to analysts in light of its prudent spending and improved fundamentals.Focus on balanced portfolioCoeur is the largest primary silver producer and one of the largest gold-producing companies in the United States and one of the largest silver companies in the world. Incorporated in 1928, the U.S.-listed company has a total of five operations: three in the United States, one in Mexico and one in Bolivia. About two-thirds of its revenue comes from the United States.The company is conscientious about having a balanced portfolio, so no single mine accounts for more than about 30 percent of its business. Being in three different jurisdictions provides further diversification, and its revenue split of about 60 percent from gold and 40 percent from silver gives it some metals mix. This year, it expects to produce about 466 t (15 million oz) of silver and 10.3 t (330,000 oz) of gold."

Feb 1, 2017

"When boring a tunnel, homogeneous hard rock is the exception rather than the rule. While contractors can set goals such as meters per month and performance incentives, it is also prudent to plan for difficult ground. A properly designed tunnel boring machine (TBM) can tackle fault zones, water inflows, squeezing ground, or whatever the risk may be. The alternative is not a good one: modifying the machine in the tunnel after bad ground is encountered. Not only does this result in increased downtime, but it also needlessly exposes the crew to the tunnel conditions. In the worst case scenario, the entire operation grinds to a halt.However, an accurate GBR cannot always be obtained, particularly for mountainous, high cover tunnels in remote locations. And even with a thorough GBR, unforeseen geological events can occur. What can be done in these situations? Difficult Ground Solutions (DGS) is ground investigation system with a suite of options that can be added to a shielded hard rock machine or dual-mode, Crossover machine to better enable advance when conditions are unknown or difficult conditions are anticipated.DGS consists of a set of integrated features tailored to a specific project’s geology. The main components of the system allow for ground investigation ahead of the TBM, increased monitoring and methods to keep a machine shield from becoming stuck.In fault zones and squeezing groundIf fault zones or squeezing ground are known or suspected, or if there is even a possibility of encountering them, this can greatly affect the TBM operation. Shielded machines protect the crew from the surrounding rock, and they can bore and line a tunnel efficiently, but in fault zones and converging material their shields can be their downfall. Avoiding a stuck machine is paramount to project success. DGS employs several features to avoid the problem of a machine becoming stuck. The first of these is multi-speed cutterhead drives. These drives effectively give the machine multiple modes of operation—high speed, low torque for hard rock, and low speed, high torque for difficult ground. Designing a machine with high-torque, continuous boring capabilities allows that machine’s cutterhead to restart with break-out torque in difficult ground. The net effect is that the machine can keep boring in the event of a face collapse and can bore through fault zones and running ground where the potential for cutterhead jamming exists. Going one step further, multi-speed gearboxes give the machine the ideal earth pressure balance- (EPB-) type torque if larger sections of soft ground are anticipated.Secondly, TBMs can get through squeezing ground and faults using Continuous Shield Advance. This design utilizes a stepped shield configuration — where each successive shield is slightly smaller in diameter — to avoid becoming stuck in converging ground. External shield lubrication is an added insurance against becoming stuck, using a series of radial ports that can pump Bentonite into the annular space to act as a lubricant in squeezing material.As a last effort, if a machine has already become stuck the TBM can utilize augmented, or “super” thrust. Additional thrust jacks can be added to supply an extra boost in a short stroke, generating enough force to break loose a trapped shield."

Jan 12, 2017

By Kim B. Shedd, Erin A. McCullough, Donald I. Bleiwas

"The earliest known use of cobalt was to make blue glass in Mesopotamia before 2000 B.C.E. Since then, innovations across many diverse industrial sectors transformed cobalt into an essential commodity for contemporary society. The physical and chemical properties of the element cobalt and its alloys and compounds make them indispensable for a variety of applications, including aircraft engines, hybrid electric vehicles, machine tools, missile guidance systems, petroleum refining and smartphones. As a major industrialized nation, the United States is a leading consumer of cobalt and cobalt-containing products. However, with few exceptions, U.S. cobaltcontaining ore deposits are of low cobalt grade. Historically, U.S. cobalt mine and refinery output have not met domestic cobalt demand. As a result, U.S. cobalt chemical and alloy producers need to procure most of their cobalt from the international market, which can become susceptible to supply risk.The 1978 Cobalt Crisis illustrates supply risk. At that time, the Democratic Republic of the Congo (DRC) (then known as Zaire) was the world’s leading producer of mined and refined cobalt. An insurgent invasion of the country’s copper-cobalt mining region during a period of high cobalt demand and low producer inventories caused a temporary supply shortage in the international market. The monthly average cobalt spot price increased from $18/ kg ($8/lb) before the crisis to $99/kg ($45/lb) seven months later. The high price and concern about potential disruptions in supply prompted manufacturers to reduce or substitute for cobalt where possible, and encouraged increased recovery of cobalt from scrap. The DRC has regained its position as the leading producer of mined cobalt globally and continues to be characterized by high governance risks (U.S. Central Intelligence Agency, 2015; World Bank, undated). This article will present current and historical world cobalt production trends, which can help inform discussion about the variety of international supply chain risks consequential to its trade."

Jan 12, 2017

By S. E. Vanderslice, J. A. Hummer

"The results of laboratory evaluations were used to compare the potential of two alternative, biomass-derived fuels as a control strategy to reduce the exposure of underground miners to aerosols and gases emitted by diesel-powered equipment. The effects of fatty acid methyl ester (FAME) biodiesel and hydrotreated vegetable oil renewable diesel (HVORD) on criteria aerosol and gaseous emissions from an older-technology, naturally aspirated, mechanically controlled engine equipped with a diesel oxidation catalytic converter were compared with those of widely used petroleum-derived, ultralow-sulfur diesels (ULSDs). The emissions were characterized for four selected steady-state conditions. When fueled with FAME biodiesel and HVORD, the engine emitted less aerosols by total particulate mass, total carbon mass, elemental carbon mass and total number than when it was fueled with ULSDs. Compared with ULSDs, FAME biodiesel and HVORD produced aerosols that were characterized by single modal distributions, smaller count median diameters, and lower total and peak concentrations. For the majority of test cases, FAME biodiesel and HVORD favorably affected nitric oxide (NO) and adversely affected nitrogen dioxide (NO2) generation. Therefore, the use of these alternative fuels appears to be a viable tool for the underground mining industry to address the issues related to emissions from diesel engines, and to transition toward more universal solutions provided by advanced engines with integrated exhaust aftertreatment technologies. IntroductionDiesel engines have been the workhorses of modern society for industrial and transportation enterprises. Diesel engines of all generations are extensively used in a variety of light-, medium- and heavy-duty applications in underground mining operations around the world. Fuels obtained from various sources and with wide-ranging chemistries have been combusted in diesel engines. However, the bulk of the currently used fuel can still be traced to nonrenewable petroleum sources. The petroleum-derived diesel fuels are primarily made up of saturated acyclic hydrocarbons (parafins or alkanes), aromatic hydrocarbons (arenes or aryl hydrocarbon), and unsaturated hydrocarbons with double bonds (olefins and alkenes). Improvements in the quality of petroleum-based diesel fuels was identified in federal regulations as an important piece in resolving the puzzle of diesel engine emissions (Environmental Protection Agency, 2001, 2004). The reduction of U.S. diesel fuel sulfur content below 15 ppm had the effect of lowering sulfate emissions and enabling the development and implementation of catalyzed emissions control technology across a wide spectrum of applications."

Jan 12, 2017

By Bjorn Olsson

"Heavy impact. High frequency hammering. Extreme abrasion. Building on the experience of owning and operating its own mines, Ovako has developed a deep knowledge of how vital the right steel properties are in withstanding the extreme loads encountered in every part of the drill string. That is why Ovako’s product development process is focused on understanding the specific load cases and manufacturing operations associated with rock tools.The punishing conditions of percussive drilling can push the limits of most materials. And heavy mechanical loads are only the beginning. Highimpact energies at high frequency are a major source of fatigue. High temperatures result from impact energy losses. And abrasive, erosive and adhesive wear are constant risks. Handling any of these varying demands at a single point along the drill string is difficult enough — which makes optimizing for the entire drilling system an extremely complex challenge. Engineering for specific loadsOvako has specialized over many decades in analyzing the dominant loads for each of the parts and components used in rock tools, and testing for individual applications in its laboratories. The most critical fatigue properties are controlled through the steel metallurgy, and supported by performance measurements through extensive rotating bending fatigue (RBF) testing, along with special methods that combine impact load with various wear loads. The result is a fit-for-purpose steel with tightly controlled performance properties, making it possible for customers to precalculate the expected life time of their components for highly automated and repetitive processes Tailoring steels for the processing route.The same levels of control and predictability must be carried through to the customer’s own manufacturing processes. By ensuring minimal variations in chemical composition, everything from heat treatment and welding to automated machining can be carried out with high consistency. With precisely controlled material properties based on an existing processing route and exact load case, customers are able to minimize their total tool production costs while ensuring optimal performance for their end products. Development of Hybrid SteelBuilding on this experience in the mining industry, Ovako has developed a new steel family, known as Hybrid Steel, designed to meet the demands of high-stress, elevatedtemperature applications where mechanical and fatigue strength are critical. Traditionally, steels for these applications are produced by expensive small-batch processes. Hybrid Steel, however, enables high volume production at a competitive cost.The world of steel has traditionally been divided into clearly separated categories of tool steel, stainless steel and lower alloy engineering steel. Hybrid Steel is now challenging that division, offering attractive properties from all three categories."

Jan 12, 2017

By Mikael Ramström, Mark Board, Clayr Alexander, Wes Johnson

"The Coeur d’Alene mining district in northern Idaho was first discovered more than 130 years ago and has been the most prolific silver producer in the United States. The Lucky Friday Mine of Hecla Mining Co. (Fig. 1) is the oldest (76 years) and deepest mine in the district, producing approximately 725 t/day (800 stpd) from narrow, vertical lead-zinc-silver veins. Cut-and-fill stoping is currently employed at depths to about 2.3 km (7,500 ft) below ground surface, making it one of the three deepest mines in the western hemisphere. The #4 Shaft, a winze collared at approximately 1.8 km (5,900 ft) below surface and extending to a depth of nearly 2.9 km (9,600 ft), was recently completed to exploit the high-grade 30 Vein, whose resource has been identified to at least 3 km (9,700 ft) in depth.As with other deep mines worldwide, a number of challenging engineering issues occur, including: high in situ rock stress, squeezing ground, seismicity, high in situ rock temperature that requires refrigeration, diesel equipment that generates diesel particulate matter (DPM) requiring high ventilation airflow rates and long travel times for worker transport to mining areas.This article describes the methods that Hecla Mining Co. has employed during the past 50 years to combat these issues, with emphasis on the current efforts to implement continuous, mechanical mining with automated or teleremote operation and to introduce electric and battery-powered equipment to minimize refrigeration and ventilation requirements for the removal of DPMs.Geology and in situ stressThe host rock mass is an extremely thick sedimentary sequence (the Belt Series) that has been tilted vertically by mountain building. The rock mass in the current section of the mine consists of weak, heavily foliated argillites and stronger, bedded silty-argillites termed siltite. The vertical veins (80° to 85° dip) are parallel to the foliation with an approximate width of around 3 m (10 ft). There are two regional, vertical faults that parallel the vein; one forming the hangingwall of the orebody and one approximately 90 m (300 ft) in the footwall. Additionally, there are several thin, rough northdipping faults that occur in the footwall of the vein which terminate on the major vertical faults.Both the argillite and vein package rock have moderate strength, with uniaxial compressive strength averaging about 100 MPa (14,700 psi with a range from about 70 to 125 MPa), and are moderately abrasive, with CERCHAR abrasivity index of 2 to 3. The major in situ stress is horizontal and oriented in a northwest direction with magnitude about 1.5 times the vertical stress. Consequently, the Lucky Friday stress magnitude at depth is analogous to significantly deeper South African gold operations."

Jan 12, 2017

By J. Sidhom, W. Fourie

"As the mining industry continues to face difficult challenges the need to persistently focus on productivity and utilization of labor and equipment costs will intensify. With these challenges in mind, Komatsu is helping to bring mining performance and analytics to the next level.By evaluating underground haulage, a significant component of the room and pillar mining value stream, variables have been identified and sensitivities have been performed to show opportunities to balance and streamline throughput. As a result of applying operational excellence tools to the mining environment, Komatsu is seeking to optimize mining performances by limiting waste, simplifying the process, increasing productivity and machine utilization, as well as removing workers from harm’s way.These days it’s not enough to work harder; mines have to work smarter. Improving efficiency, reducing costs, increasing safety: these are no longer nice to haves, they are must haves.Starting with the best products and the right people is a first step, but then what? How do mines take their operations from average to being a top performer? By using operational excellence principles aimed at eliminating waste, simplifying processes, automating where possible and removing people from harm’s way.The fundamentals of operational excellence (OpEx) are based upon the process of define, measure, analyze, improve and control (DMAIC). DMAIC is an improvement cycle that helps with, for example, haulage optimization by: defining the issues and problems in the process as well as the areas of improvement; measuring and collecting mining operational data by time study and equipment monitoring system; analyzing through sensitivities and production modelling to determine root causes and then improving the performance and controlling the operation.Komatsu uses OpEx or lean principles inside its organization to drive efficiency, but it also helps its customers employ them to achieve new levels of productivity and safety.These same principles can be applied in most situations to streamline processes, improve operations and deliver value."

Jan 12, 2017

By William Gleason

"On April 4, 2017, the largest earth-pressure-balance tunnel boring machine (TBM) ever built finally completed its 2.7-km (1.7-mile) journey beneath Seattle, WA, nearly four years after it began boring the SR-99 tunnel that will eventually replace Seattle’s Alaskan Way Viaduct.By now, readers of this publication are familiar with the ordeal that began on Dec. 6, 2016, when the machine overheated and shut down. Until that point, the TBM, named Bertha, had grabbed headlines for being the largest in the world with a 17-m (57.6-ft) diameter face. But after the incident that stopped the progress, the headlines suddenly stopped focusing on the engineering marvel of the tunnel project and began asking what went wrong. Just 300 m (1,000 ft) into the tunneling journey the machine was stuck, unable to move forward and impossible to retract.The project’s contractors, Seattle Tunnel Partners,(STP JV) – a design-build consortium comprised of Dragados - USA, Tutor Perini, say a 20-cm (8-in.) steel well-casing buried in the path of the machine caused the problems that halted the TBM. The Washington State Department of Transportation (WSDOT) disagrees, and the issue over who ultimately pays for the repairs is now with the courts.Eventually, engineers determined the best way to get Bertha back to work was to dig a 36-m (120-ft), deep concrete lined shaft pit in front of the machine and lift the 1.8-kt (2,000-st) cutterhead out for repairs. The repairs took two years but eventually the machine resumed mining in January 2016. In April 2017, the TBM finished building the tunnel, breaking through at the tunnel’s north end near Seattle’s Space Needle, with little to no ground surface movement measured on the entire alignment.While the cause of the TBM breakdown and who should pay for repairs was debated above ground, the work below ground continued. David Sowers, deputy program administrator, engineering and program management with WSDOT, told Mining Engineering during the 2017 Cutting Edge Conference in Seattle that in addition to the technical marvel that the tunnel became, the fact the parties involved were able to work through the unprecedented challenge is a great example of how to overcome challenges on massive projects."

Jan 12, 2017

By David Crouthamel, Raymond Henn

"The need to fill the void space or annulus created between an excavated tunnel or shaft and the final lining system has long been a requirement in underground construction. Most of those types of voids are created as a result of employing the two pass tunneling lining method. Filling of this void is called backfilling. For many years the materials used as backfill were primarily reinforced and non-reinforced concrete, sanded grout, neat cement grout, or blown-in sand/pea gravel. However, in the past 20 years the use of cellular grouts/cellular concrete as the backfill material has greatly increased. Most cellular grout is made of a mixture of water, Portland cement (with or without the addition of fly ash), a foaming agent and admixtures such as a water-reducer or superplasticizer.It is the authors’ preference to use the term cellular grout as opposed to cellular concrete since by ACI Concrete Terminology an ACI Standard (ACI CT 13), concrete contains aggregates. Normally cellular grout does not contain sand (finite aggregate), but almost never contain course aggregates.The authors believe there are several reasons for this increased use of cellular grout as backfill, such as:• The increase utilization of the various trenchless tunneling methods. Tunnels constructed using trenchless method tend to be smaller in size, excavated diameter or cross sectional area. Making man-entry for placing backfill from inside the secondary liner, utilizing pre-installed grout posts, more difficult if not impossible. It is these workspace restrictions that are the drivers as to when to utilize grout ports installed during the pipe/liner fabrication versus grout delivery pipes installed within the void/annulus space.• The ability of cellular backfills to be pumped and flow longer distances.• The unit weight of cellular grouts can be controlled by mix design and generally can range from 560 Kg/m3 (35 lbs/CF) to 1040 Kg/m3 (65 lbs/CF)."

Jan 12, 2017